diff options
Diffstat (limited to 'qemu/roms/u-boot/board/freescale/mpc8568mds')
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc8568mds/Makefile | 13 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc8568mds/bcsr.c | 61 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc8568mds/bcsr.h | 93 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc8568mds/ddr.c | 56 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc8568mds/law.c | 41 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc8568mds/mpc8568mds.c | 354 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc8568mds/tlb.c | 84 |
7 files changed, 702 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/freescale/mpc8568mds/Makefile b/qemu/roms/u-boot/board/freescale/mpc8568mds/Makefile new file mode 100644 index 000000000..612fb5154 --- /dev/null +++ b/qemu/roms/u-boot/board/freescale/mpc8568mds/Makefile @@ -0,0 +1,13 @@ +# +# Copyright 2004-2007 Freescale Semiconductor. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += mpc8568mds.o +obj-y += bcsr.o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/qemu/roms/u-boot/board/freescale/mpc8568mds/bcsr.c b/qemu/roms/u-boot/board/freescale/mpc8568mds/bcsr.c new file mode 100644 index 000000000..4a6105cb1 --- /dev/null +++ b/qemu/roms/u-boot/board/freescale/mpc8568mds/bcsr.c @@ -0,0 +1,61 @@ +/* + * Copyright 2007 Freescale Semiconductor. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> + +#include "bcsr.h" + +void enable_8568mds_duart(void) +{ + volatile uint* duart_mux = (uint *)(CONFIG_SYS_CCSRBAR + 0xe0060); + volatile uint* devices = (uint *)(CONFIG_SYS_CCSRBAR + 0xe0070); + volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR); + + *duart_mux = 0x80000000; /* Set the mux to Duart on PMUXCR */ + *devices = 0; /* Enable all peripheral devices */ + bcsr[5] |= 0x01; /* Enable Duart in BCSR*/ +} + +void enable_8568mds_flash_write(void) +{ + volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR); + + bcsr[9] |= 0x01; +} + +void disable_8568mds_flash_write(void) +{ + volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR); + + bcsr[9] &= ~(0x01); +} + +void enable_8568mds_qe_mdio(void) +{ + u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR); + + bcsr[7] |= 0x01; +} + +#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2) +void reset_8568mds_uccs(void) +{ + volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR); + + /* Turn off UCC1 & UCC2 */ + out_8(&bcsr[8], in_8(&bcsr[8]) & ~BCSR_UCC1_GETH_EN); + out_8(&bcsr[9], in_8(&bcsr[9]) & ~BCSR_UCC2_GETH_EN); + + /* Mode is RGMII, all bits clear */ + out_8(&bcsr[11], in_8(&bcsr[11]) & ~(BCSR_UCC1_MODE_MSK | + BCSR_UCC2_MODE_MSK)); + + /* Turn UCC1 & UCC2 on */ + out_8(&bcsr[8], in_8(&bcsr[8]) | BCSR_UCC1_GETH_EN); + out_8(&bcsr[9], in_8(&bcsr[9]) | BCSR_UCC2_GETH_EN); +} +#endif diff --git a/qemu/roms/u-boot/board/freescale/mpc8568mds/bcsr.h b/qemu/roms/u-boot/board/freescale/mpc8568mds/bcsr.h new file mode 100644 index 000000000..215534e6c --- /dev/null +++ b/qemu/roms/u-boot/board/freescale/mpc8568mds/bcsr.h @@ -0,0 +1,93 @@ +/* + * Copyright 2007 Freescale Semiconductor. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __BCSR_H_ +#define __BCSR_H_ + +#include <common.h> + +/* BCSR Bit definitions + * BCSR 0 * + 0:3 ccb sys pll + 4:6 cfg core pll + 7 cfg boot seq + + * BCSR 1 * + 0:2 cfg rom lock + 3:5 cfg host agent + 6 PCI IO + 7 cfg RIO size + + * BCSR 2 * + 0:4 QE PLL + 5 QE clock + 6 cfg PCI arbiter + + * BCSR 3 * + 0 TSEC1 reduce + 1 TSEC2 reduce + 2:3 TSEC1 protocol + 4:5 TSEC2 protocol + 6 PHY1 slave + 7 PHY2 slave + + * BCSR 4 * + 4 clock enable + 5 boot EPROM + 6 GETH transactive reset + 7 BRD write potect + + * BCSR 5 * + 1:3 Leds 1-3 + 4 UPC1 enable + 5 UPC2 enable + 6 UPC2 pos + 7 RS232 enable + + * BCSR 6 * + 0 CFG ver 0 + 1 CFG ver 1 + 6 Register config led + 7 Power on reset + + * BCSR 7 * + 2 board host mode indication + 5 enable TSEC1 PHY + 6 enable TSEC2 PHY + + * BCSR 8 * + 0 UCC GETH1 enable + 1 UCC GMII enable + 3 UCC TBI enable + 5 UCC MII enable + 7 Real time clock reset + + * BCSR 9 * + 0 UCC2 GETH enable + 1 UCC2 GMII enable + 3 UCC2 TBI enable + 5 UCC2 MII enable + 6 Ready only - indicate flash ready after burning + 7 Flash write protect +*/ + +#define BCSR_UCC1_GETH_EN (0x1 << 7) +#define BCSR_UCC2_GETH_EN (0x1 << 7) +#define BCSR_UCC1_MODE_MSK (0x3 << 4) +#define BCSR_UCC2_MODE_MSK (0x3 << 0) + +/*BCSR Utils functions*/ + +void enable_8568mds_duart(void); +void enable_8568mds_flash_write(void); +void disable_8568mds_flash_write(void); +void enable_8568mds_qe_mdio(void); + +#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2) +void reset_8568mds_uccs(void); +#endif + +#endif /* __BCSR_H_ */ diff --git a/qemu/roms/u-boot/board/freescale/mpc8568mds/ddr.c b/qemu/roms/u-boot/board/freescale/mpc8568mds/ddr.c new file mode 100644 index 000000000..6db92ef2d --- /dev/null +++ b/qemu/roms/u-boot/board/freescale/mpc8568mds/ddr.c @@ -0,0 +1,56 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> + +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + /* + * Factors to consider for clock adjust: + * - number of chips on bus + * - position of slot + * - DDR1 vs. DDR2? + * - ??? + * + * This needs to be determined on a board-by-board basis. + * 0110 3/4 cycle late + * 0111 7/8 cycle late + */ + popts->clk_adjust = 6; + + /* + * Factors to consider for CPO: + * - frequency + * - ddr1 vs. ddr2 + */ + popts->cpo_override = 10; + + /* + * Factors to consider for write data delay: + * - number of DIMMs + * + * 1 = 1/4 clock delay + * 2 = 1/2 clock delay + * 3 = 3/4 clock delay + * 4 = 1 clock delay + * 5 = 5/4 clock delay + * 6 = 3/2 clock delay + */ + popts->write_data_delay = 3; + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/qemu/roms/u-boot/board/freescale/mpc8568mds/law.c b/qemu/roms/u-boot/board/freescale/mpc8568mds/law.c new file mode 100644 index 000000000..ae0696611 --- /dev/null +++ b/qemu/roms/u-boot/board/freescale/mpc8568mds/law.c @@ -0,0 +1,41 @@ +/* + * Copyright 2008, 2010-2011 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * LAW(Local Access Window) configuration: + * + *0) 0x0000_0000 0x7fff_ffff DDR 2G + *1) 0x8000_0000 0x9fff_ffff PCI1 MEM 512MB + *2) 0xa000_0000 0xbfff_ffff PCIe MEM 512MB + *-) 0xe000_0000 0xe00f_ffff CCSR 1M + *3) 0xe200_0000 0xe27f_ffff PCI1 I/O 8M + *4) 0xe280_0000 0xe2ff_ffff PCIe I/O 8M + *5) 0xc000_0000 0xdfff_ffff SRIO 512MB + *6.a) 0xf000_0000 0xf3ff_ffff SDRAM 64MB + *6.b) 0xf800_0000 0xf800_7fff BCSR 32KB + *6.c) 0xf800_8000 0xf800_ffff PIB (CS4) 32KB + *6.d) 0xf801_0000 0xf801_7fff PIB (CS5) 32KB + *6.e) 0xfe00_0000 0xffff_ffff Flash 32MB + * + *Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + * + */ + +struct law_entry law_table[] = { + /* LBC window - maps 256M. That's SDRAM, BCSR, PIBs, and Flash */ + SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/qemu/roms/u-boot/board/freescale/mpc8568mds/mpc8568mds.c b/qemu/roms/u-boot/board/freescale/mpc8568mds/mpc8568mds.c new file mode 100644 index 000000000..a8fdcb5f9 --- /dev/null +++ b/qemu/roms/u-boot/board/freescale/mpc8568mds/mpc8568mds.c @@ -0,0 +1,354 @@ +/* + * Copyright 2007,2009-2011 Freescale Semiconductor, Inc. + * + * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <pci.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <fsl_ddr_sdram.h> +#include <asm/fsl_serdes.h> +#include <spd_sdram.h> +#include <i2c.h> +#include <ioports.h> +#include <libfdt.h> +#include <fdt_support.h> + +#include "bcsr.h" + +const qe_iop_conf_t qe_iop_conf_tab[] = { + /* GETH1 */ + {4, 10, 1, 0, 2}, /* TxD0 */ + {4, 9, 1, 0, 2}, /* TxD1 */ + {4, 8, 1, 0, 2}, /* TxD2 */ + {4, 7, 1, 0, 2}, /* TxD3 */ + {4, 23, 1, 0, 2}, /* TxD4 */ + {4, 22, 1, 0, 2}, /* TxD5 */ + {4, 21, 1, 0, 2}, /* TxD6 */ + {4, 20, 1, 0, 2}, /* TxD7 */ + {4, 15, 2, 0, 2}, /* RxD0 */ + {4, 14, 2, 0, 2}, /* RxD1 */ + {4, 13, 2, 0, 2}, /* RxD2 */ + {4, 12, 2, 0, 2}, /* RxD3 */ + {4, 29, 2, 0, 2}, /* RxD4 */ + {4, 28, 2, 0, 2}, /* RxD5 */ + {4, 27, 2, 0, 2}, /* RxD6 */ + {4, 26, 2, 0, 2}, /* RxD7 */ + {4, 11, 1, 0, 2}, /* TX_EN */ + {4, 24, 1, 0, 2}, /* TX_ER */ + {4, 16, 2, 0, 2}, /* RX_DV */ + {4, 30, 2, 0, 2}, /* RX_ER */ + {4, 17, 2, 0, 2}, /* RX_CLK */ + {4, 19, 1, 0, 2}, /* GTX_CLK */ + {1, 31, 2, 0, 3}, /* GTX125 */ + + /* GETH2 */ + {5, 10, 1, 0, 2}, /* TxD0 */ + {5, 9, 1, 0, 2}, /* TxD1 */ + {5, 8, 1, 0, 2}, /* TxD2 */ + {5, 7, 1, 0, 2}, /* TxD3 */ + {5, 23, 1, 0, 2}, /* TxD4 */ + {5, 22, 1, 0, 2}, /* TxD5 */ + {5, 21, 1, 0, 2}, /* TxD6 */ + {5, 20, 1, 0, 2}, /* TxD7 */ + {5, 15, 2, 0, 2}, /* RxD0 */ + {5, 14, 2, 0, 2}, /* RxD1 */ + {5, 13, 2, 0, 2}, /* RxD2 */ + {5, 12, 2, 0, 2}, /* RxD3 */ + {5, 29, 2, 0, 2}, /* RxD4 */ + {5, 28, 2, 0, 2}, /* RxD5 */ + {5, 27, 2, 0, 3}, /* RxD6 */ + {5, 26, 2, 0, 2}, /* RxD7 */ + {5, 11, 1, 0, 2}, /* TX_EN */ + {5, 24, 1, 0, 2}, /* TX_ER */ + {5, 16, 2, 0, 2}, /* RX_DV */ + {5, 30, 2, 0, 2}, /* RX_ER */ + {5, 17, 2, 0, 2}, /* RX_CLK */ + {5, 19, 1, 0, 2}, /* GTX_CLK */ + {1, 31, 2, 0, 3}, /* GTX125 */ + {4, 6, 3, 0, 2}, /* MDIO */ + {4, 5, 1, 0, 2}, /* MDC */ + + /* UART1 */ + {2, 0, 1, 0, 2}, /* UART_SOUT1 */ + {2, 1, 1, 0, 2}, /* UART_RTS1 */ + {2, 2, 2, 0, 2}, /* UART_CTS1 */ + {2, 3, 2, 0, 2}, /* UART_SIN1 */ + + {0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */ +}; + +void local_bus_init(void); + +int board_early_init_f (void) +{ + /* + * Initialize local bus. + */ + local_bus_init (); + + enable_8568mds_duart(); + enable_8568mds_flash_write(); +#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2) + reset_8568mds_uccs(); +#endif +#if defined(CONFIG_QE) && !defined(CONFIG_eTSEC_MDIO_BUS) + enable_8568mds_qe_mdio(); +#endif + +#ifdef CONFIG_SYS_I2C2_OFFSET + /* Enable I2C2_SCL and I2C2_SDA */ + volatile struct par_io *port_c; + port_c = (struct par_io*)(CONFIG_SYS_IMMR + 0xe0140); + port_c->cpdir2 |= 0x0f000000; + port_c->cppar2 &= ~0x0f000000; + port_c->cppar2 |= 0x0a000000; +#endif + + return 0; +} + +int checkboard (void) +{ + printf ("Board: 8568 MDS\n"); + + return 0; +} + +/* + * Initialize Local Bus + */ +void +local_bus_init(void) +{ + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; + + uint clkdiv; + sys_info_t sysinfo; + + get_sys_info(&sysinfo); + clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; + + gur->lbiuiplldcr1 = 0x00078080; + if (clkdiv == 16) { + gur->lbiuiplldcr0 = 0x7c0f1bf0; + } else if (clkdiv == 8) { + gur->lbiuiplldcr0 = 0x6c0f1bf0; + } else if (clkdiv == 4) { + gur->lbiuiplldcr0 = 0x5c0f1bf0; + } + + lbc->lcrr |= 0x00030000; + + asm("sync;isync;msync"); +} + +/* + * Initialize SDRAM memory on the Local Bus. + */ +void lbc_sdram_init(void) +{ +#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM) + + uint idx; + volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; + uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE; + uint lsdmr_common; + + puts("LBC SDRAM: "); + print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, + "\n "); + + /* + * Setup SDRAM Base and Option Registers + */ + set_lbc_or(2, CONFIG_SYS_OR2_PRELIM); + set_lbc_br(2, CONFIG_SYS_BR2_PRELIM); + asm("msync"); + + lbc->lbcr = CONFIG_SYS_LBC_LBCR; + asm("msync"); + + lbc->lsrt = CONFIG_SYS_LBC_LSRT; + lbc->mrtpr = CONFIG_SYS_LBC_MRTPR; + asm("msync"); + + /* + * MPC8568 uses "new" 15-16 style addressing. + */ + lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON; + lsdmr_common |= LSDMR_BSMA1516; + + /* + * Issue PRECHARGE ALL command. + */ + lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + + /* + * Issue 8 AUTO REFRESH commands. + */ + for (idx = 0; idx < 8; idx++) { + lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + } + + /* + * Issue 8 MODE-set command. + */ + lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + + /* + * Issue NORMAL OP command. + */ + lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(200); /* Overkill. Must wait > 200 bus cycles */ + +#endif /* enable SDRAM init */ +} + +#if defined(CONFIG_PCI) +#ifndef CONFIG_PCI_PNP +static struct pci_config_table pci_mpc8568mds_config_table[] = { + { + PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, + pci_cfgfunc_config_device, + {PCI_ENET0_IOADDR, + PCI_ENET0_MEMADDR, + PCI_COMMON_MEMORY | PCI_COMMAND_MASTER} + }, + {} +}; +#endif + +static struct pci_controller pci1_hose; +#endif /* CONFIG_PCI */ + +/* + * pib_init() -- Initialize the PCA9555 IO expander on the PIB board + */ +void +pib_init(void) +{ + u8 val8, orig_i2c_bus; + /* + * Assign PIB PMC2/3 to PCI bus + */ + + /*switch temporarily to I2C bus #2 */ + orig_i2c_bus = i2c_get_bus_num(); + i2c_set_bus_num(1); + + val8 = 0x00; + i2c_write(0x23, 0x6, 1, &val8, 1); + i2c_write(0x23, 0x7, 1, &val8, 1); + val8 = 0xff; + i2c_write(0x23, 0x2, 1, &val8, 1); + i2c_write(0x23, 0x3, 1, &val8, 1); + + val8 = 0x00; + i2c_write(0x26, 0x6, 1, &val8, 1); + val8 = 0x34; + i2c_write(0x26, 0x7, 1, &val8, 1); + val8 = 0xf9; + i2c_write(0x26, 0x2, 1, &val8, 1); + val8 = 0xff; + i2c_write(0x26, 0x3, 1, &val8, 1); + + val8 = 0x00; + i2c_write(0x27, 0x6, 1, &val8, 1); + i2c_write(0x27, 0x7, 1, &val8, 1); + val8 = 0xff; + i2c_write(0x27, 0x2, 1, &val8, 1); + val8 = 0xef; + i2c_write(0x27, 0x3, 1, &val8, 1); + + asm("eieio"); + i2c_set_bus_num(orig_i2c_bus); +} + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + int first_free_busno = 0; +#ifdef CONFIG_PCI1 + struct fsl_pci_info pci_info; + u32 devdisr, pordevsr, io_sel; + u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel; + + devdisr = in_be32(&gur->devdisr); + pordevsr = in_be32(&gur->pordevsr); + porpllsr = in_be32(&gur->porpllsr); + io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19; + + debug (" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel); + + pci_speed = 66666000; + pci_32 = 1; + pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; + pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; + + if (!(devdisr & MPC85xx_DEVDISR_PCI1)) { + SET_STD_PCI_INFO(pci_info, 1); + set_next_law(pci_info.mem_phys, + law_size_bits(pci_info.mem_size), pci_info.law); + set_next_law(pci_info.io_phys, + law_size_bits(pci_info.io_size), pci_info.law); + + pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs); + printf("PCI: %d bit, %s MHz, %s, %s, %s (base address %lx)\n", + (pci_32) ? 32 : 64, + (pci_speed == 33333000) ? "33" : + (pci_speed == 66666000) ? "66" : "unknown", + pci_clk_sel ? "sync" : "async", + pci_agent ? "agent" : "host", + pci_arb ? "arbiter" : "external-arbiter", + pci_info.regs); + +#ifndef CONFIG_PCI_PNP + pci1_hose.config_table = pci_mpc8568mds_config_table; +#endif + first_free_busno = fsl_pci_init_port(&pci_info, + &pci1_hose, first_free_busno); + } else { + printf("PCI: disabled\n"); + } + + puts("\n"); +#else + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */ +#endif + + fsl_pcie_init_board(first_free_busno); +} +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); + + FT_FSL_PCI_SETUP; +} +#endif diff --git a/qemu/roms/u-boot/board/freescale/mpc8568mds/tlb.c b/qemu/roms/u-boot/board/freescale/mpc8568mds/tlb.c new file mode 100644 index 000000000..b5e2fec1f --- /dev/null +++ b/qemu/roms/u-boot/board/freescale/mpc8568mds/tlb.c @@ -0,0 +1,84 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 Initializations */ + /* + * TLBe 0: 16M Non-cacheable, guarded + * 0xff000000 16M FLASH (upper half) + * Out of reset this entry is only 4K. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x1000000, CONFIG_SYS_FLASH_BASE + 0x1000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_16M, 1), + + /* + * TLBe 1: 16M Non-cacheable, guarded + * 0xfe000000 16M FLASH (lower half) + */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* + * TLBe 2: 1G Non-cacheable, guarded + * 0x80000000 512M PCI1 MEM + * 0xa0000000 512M PCIe MEM + */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_VIRT, CONFIG_SYS_PCI1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1G, 1), + + /* + * TLBe 3: 64M Non-cacheable, guarded + * 0xe000_0000 1M CCSRBAR + * 0xe200_0000 8M PCI1 IO + * 0xe280_0000 8M PCIe IO + */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_64M, 1), + + /* + * TLBe 4: 64M Cacheable, non-guarded + * 0xf000_0000 64M LBC SDRAM + */ + SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 4, BOOKE_PAGESZ_64M, 1), + + /* + * TLBe 5: 256K Non-cacheable, guarded + * 0xf8000000 32K BCSR + * 0xf8008000 32K PIB (CS4) + * 0xf8010000 32K PIB (CS5) + */ + SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256K, 1), +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); |