diff options
Diffstat (limited to 'qemu/roms/u-boot/board/freescale/mpc837xemds/mpc837xemds.c')
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc837xemds/mpc837xemds.c | 345 |
1 files changed, 345 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/freescale/mpc837xemds/mpc837xemds.c b/qemu/roms/u-boot/board/freescale/mpc837xemds/mpc837xemds.c new file mode 100644 index 000000000..0a3c9720d --- /dev/null +++ b/qemu/roms/u-boot/board/freescale/mpc837xemds/mpc837xemds.c @@ -0,0 +1,345 @@ +/* + * Copyright (C) 2007,2010 Freescale Semiconductor, Inc. + * Dave Liu <daveliu@freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <hwconfig.h> +#include <i2c.h> +#include <asm/io.h> +#include <asm/fsl_mpc83xx_serdes.h> +#include <asm/fsl_enet.h> +#include <spd_sdram.h> +#include <tsec.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <fsl_esdhc.h> +#include <fsl_mdio.h> +#include <phy.h> +#include "pci.h" +#include "../common/pq-mds-pib.h" + +int board_early_init_f(void) +{ + u8 *bcsr = (u8 *)CONFIG_SYS_BCSR; + + /* Enable flash write */ + bcsr[0x9] &= ~0x04; + /* Clear all of the interrupt of BCSR */ + bcsr[0xe] = 0xff; + +#ifdef CONFIG_FSL_SERDES + immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; + u32 spridr = in_be32(&immr->sysconf.spridr); + + /* we check only part num, and don't look for CPU revisions */ + switch (PARTID_NO_E(spridr)) { + case SPR_8377: + fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA, + FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V); + break; + case SPR_8378: + fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII, + FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V); + break; + case SPR_8379: + fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA, + FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V); + fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_SATA, + FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V); + break; + default: + printf("serdes not configured: unknown CPU part number: " + "%04x\n", spridr >> 16); + break; + } +#endif /* CONFIG_FSL_SERDES */ + return 0; +} + +#ifdef CONFIG_FSL_ESDHC +int board_mmc_init(bd_t *bd) +{ + struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR; + u8 *bcsr = (u8 *)CONFIG_SYS_BCSR; + + if (!hwconfig("esdhc")) + return 0; + + /* Set SPI_SD, SER_SD, and IRQ4_WP so that SD signals go through */ + bcsr[0xc] |= 0x4c; + + /* Set proper bits in SICR to allow SD signals through */ + clrsetbits_be32(&im->sysconf.sicrl, SICRL_USB_B, SICRL_USB_B_SD); + clrsetbits_be32(&im->sysconf.sicrh, SICRH_GPIO2_E | SICRH_SPI, + SICRH_GPIO2_E_SD | SICRH_SPI_SD); + + return fsl_esdhc_mmc_init(bd); +} +#endif + +#if defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2) +int board_eth_init(bd_t *bd) +{ + struct fsl_pq_mdio_info mdio_info; + struct tsec_info_struct tsec_info[2]; + struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR; + u32 rcwh = in_be32(&im->reset.rcwh); + u32 tsec_mode; + int num = 0; + + /* New line after Net: */ + printf("\n"); + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + + printf(CONFIG_TSEC1_NAME ": "); + + tsec_mode = rcwh & HRCWH_TSEC1M_MASK; + if (tsec_mode == HRCWH_TSEC1M_IN_RGMII) { + printf("RGMII\n"); + /* this is default, no need to fixup */ + } else if (tsec_mode == HRCWH_TSEC1M_IN_SGMII) { + printf("SGMII\n"); + tsec_info[num].phyaddr = TSEC1_PHY_ADDR_SGMII; + tsec_info[num].flags = TSEC_GIGABIT; + } else { + printf("unsupported PHY type\n"); + } + num++; +#endif +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + + printf(CONFIG_TSEC2_NAME ": "); + + tsec_mode = rcwh & HRCWH_TSEC2M_MASK; + if (tsec_mode == HRCWH_TSEC2M_IN_RGMII) { + printf("RGMII\n"); + /* this is default, no need to fixup */ + } else if (tsec_mode == HRCWH_TSEC2M_IN_SGMII) { + printf("SGMII\n"); + tsec_info[num].phyaddr = TSEC2_PHY_ADDR_SGMII; + tsec_info[num].flags = TSEC_GIGABIT; + } else { + printf("unsupported PHY type\n"); + } + num++; +#endif + + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + fsl_pq_mdio_init(bd, &mdio_info); + + return tsec_eth_init(bd, tsec_info, num); +} + +static void __ft_tsec_fixup(void *blob, bd_t *bd, const char *alias, + int phy_addr) +{ + const u32 *ph; + int off; + int err; + + off = fdt_path_offset(blob, alias); + if (off < 0) { + printf("WARNING: could not find %s alias: %s.\n", alias, + fdt_strerror(off)); + return; + } + + err = fdt_fixup_phy_connection(blob, off, PHY_INTERFACE_MODE_SGMII); + + if (err) { + printf("WARNING: could not set phy-connection-type for %s: " + "%s.\n", alias, fdt_strerror(err)); + return; + } + + ph = (u32 *)fdt_getprop(blob, off, "phy-handle", 0); + if (!ph) { + printf("WARNING: could not get phy-handle for %s.\n", + alias); + return; + } + + off = fdt_node_offset_by_phandle(blob, *ph); + if (off < 0) { + printf("WARNING: could not get phy node for %s: %s\n", alias, + fdt_strerror(off)); + return; + } + + phy_addr = cpu_to_fdt32(phy_addr); + err = fdt_setprop(blob, off, "reg", &phy_addr, sizeof(phy_addr)); + if (err < 0) { + printf("WARNING: could not set phy node's reg for %s: " + "%s.\n", alias, fdt_strerror(err)); + return; + } +} + +static void ft_tsec_fixup(void *blob, bd_t *bd) +{ + struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR; + u32 rcwh = in_be32(&im->reset.rcwh); + u32 tsec_mode; + +#ifdef CONFIG_TSEC1 + tsec_mode = rcwh & HRCWH_TSEC1M_MASK; + if (tsec_mode == HRCWH_TSEC1M_IN_SGMII) + __ft_tsec_fixup(blob, bd, "ethernet0", TSEC1_PHY_ADDR_SGMII); +#endif + +#ifdef CONFIG_TSEC2 + tsec_mode = rcwh & HRCWH_TSEC2M_MASK; + if (tsec_mode == HRCWH_TSEC2M_IN_SGMII) + __ft_tsec_fixup(blob, bd, "ethernet1", TSEC2_PHY_ADDR_SGMII); +#endif +} +#else +static inline void ft_tsec_fixup(void *blob, bd_t *bd) {} +#endif /* defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2) */ + +int board_early_init_r(void) +{ +#ifdef CONFIG_PQ_MDS_PIB + pib_init(); +#endif + return 0; +} + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif +int fixed_sdram(void); + +phys_size_t initdram(int board_type) +{ + volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; + u32 msize = 0; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im) + return -1; + +#if defined(CONFIG_SPD_EEPROM) + msize = spd_sdram(); +#else + msize = fixed_sdram(); +#endif + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* Initialize DDR ECC byte */ + ddr_enable_ecc(msize * 1024 * 1024); +#endif + + /* return total bus DDR size(bytes) */ + return (msize * 1024 * 1024); +} + +#if !defined(CONFIG_SPD_EEPROM) +/************************************************************************* + * fixed sdram init -- doesn't use serial presence detect. + ************************************************************************/ +int fixed_sdram(void) +{ + volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; + u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024; + u32 msize_log2 = __ilog2(msize); + + im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000; + im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1); + +#if (CONFIG_SYS_DDR_SIZE != 512) +#warning Currenly any ddr size other than 512 is not supported +#endif + im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE; + udelay(50000); + + im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL; + udelay(1000); + + im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS; + im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG; + udelay(1000); + + im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0; + im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2; + im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3; + im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG; + im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2; + im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE; + im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2; + im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL; + __asm__ __volatile__("sync"); + udelay(1000); + + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + udelay(2000); + return CONFIG_SYS_DDR_SIZE; +} +#endif /*!CONFIG_SYS_SPD_EEPROM */ + +int checkboard(void) +{ + puts("Board: Freescale MPC837xEMDS\n"); + return 0; +} + +#ifdef CONFIG_PCI +int board_pci_host_broken(void) +{ + struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR; + const u32 rcw_mask = HRCWH_PCI1_ARBITER_ENABLE | HRCWH_PCI_HOST; + + /* It's always OK in case of external arbiter. */ + if (hwconfig_subarg_cmp("pci", "arbiter", "external")) + return 0; + + if ((in_be32(&im->reset.rcwh) & rcw_mask) != rcw_mask) + return 1; + + return 0; +} + +static void ft_pci_fixup(void *blob, bd_t *bd) +{ + const char *status = "broken (no arbiter)"; + int off; + int err; + + off = fdt_path_offset(blob, "pci0"); + if (off < 0) { + printf("WARNING: could not find pci0 alias: %s.\n", + fdt_strerror(off)); + return; + } + + err = fdt_setprop(blob, off, "status", status, strlen(status) + 1); + if (err) { + printf("WARNING: could not set status for pci0: %s.\n", + fdt_strerror(err)); + return; + } +} +#endif + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); + ft_tsec_fixup(blob, bd); + fdt_fixup_dr_usb(blob, bd); + fdt_fixup_esdhc(blob, bd); +#ifdef CONFIG_PCI + ft_pci_setup(blob, bd); + if (board_pci_host_broken()) + ft_pci_fixup(blob, bd); + ft_pcie_fixup(blob, bd); +#endif +} +#endif /* CONFIG_OF_BOARD_SETUP */ |