diff options
Diffstat (limited to 'qemu/roms/u-boot/board/freescale/mpc832xemds')
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc832xemds/Makefile | 9 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc832xemds/README | 128 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc832xemds/mpc832xemds.c | 164 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/freescale/mpc832xemds/pci.c | 146 |
4 files changed, 0 insertions, 447 deletions
diff --git a/qemu/roms/u-boot/board/freescale/mpc832xemds/Makefile b/qemu/roms/u-boot/board/freescale/mpc832xemds/Makefile deleted file mode 100644 index 66763519a..000000000 --- a/qemu/roms/u-boot/board/freescale/mpc832xemds/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y += mpc832xemds.o -obj-$(CONFIG_PCI) += pci.o diff --git a/qemu/roms/u-boot/board/freescale/mpc832xemds/README b/qemu/roms/u-boot/board/freescale/mpc832xemds/README deleted file mode 100644 index 4142aa9c8..000000000 --- a/qemu/roms/u-boot/board/freescale/mpc832xemds/README +++ /dev/null @@ -1,128 +0,0 @@ -Freescale MPC832XEMDS Board ------------------------------------------ -1. Board Switches and Jumpers -1.0 There are five Dual-In-Line Packages(DIP) Switches on MPC832XE SYS board - For some reason, the HW designers describe the switch settings - in terms of 0 and 1, and then map that to physical switches where - the label "On" refers to logic 0 and "Off" is logic 1. - - Switch bits are numbered 1 through, like, 4 6 8 or 10, but the - bits may contribute to signals that are numbered based at 0, - and some of those signals may be high-bit-number-0 too. Heed - well the names and labels and do not get confused. - - "Off" == 1 - "On" == 0 - - SW3 is switch 18 as silk-screened onto the board. - SW4[8] is the bit labeled 8 on Switch 4. - SW5[1:6] refers to bits labeled 1 through 6 in order on switch 5. - SW6[7:1] refers to bits labeled 7 through 1 in order on switch 6. - SW7[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On" - and bits labeled 8 is set as "Off". - -1.1 For the MPC832XEMDS PROTO Board - - First, make sure the board default setting is consistent with the document - shipped with your board. Then apply the following setting: - SW3[1-8]= 0000_1000 (core PLL setting, core enable) - SW4[1-8]= 0001_0010 (Flash boot on local bus, system PLL setting) - SW5[1-8]= 0010_0110 (Boot from high end) - SW6[1-8]= 0011_0100 (Flash boot on 16 bit local bus) - SW7[1-8]= 1000_0011 (QE PLL setting) - - ENET3/4 MII mode settings: - J1 1-2 (ETH3_TXER) - J2 2-3 (MII mode) - J3 2-3 (MII mode) - J4 2-3 (ADSL clockOscillator) - J5 1-2 (ETH4_TXER) - J6 2-3 (ClockOscillator) - JP1 removed (don't force PORESET) - JP2 mounted (ETH4/2 MII) - JP3 mounted (ETH3 MII) - JP4 mounted (HRCW from BCSR) - - ENET3/4 RMII mode settings: - J1 1-2 (ETH3_TXER) - J2 1-2 (RMII mode) - J3 1-2 (RMII mode) - J4 2-3 (ADSL clockOscillator) - J5 1-2 (ETH4_TXER) - J6 2-3 (ClockOscillator) - JP1 removed (don't force PORESET) - JP2 removed (ETH4/2 RMII) - JP3 removed (ETH3 RMII) - JP4 removed (HRCW from FLASH) - - on board Oscillator: 66M - - -2. Memory Map - -2.1 The memory map should look pretty much like this: - - 0x0000_0000 0x7fff_ffff DDR 2G - 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M - 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M - 0xc000_0000 0xdfff_ffff Empty 512M - 0xe000_0000 0xe01f_ffff Int Mem Reg Space 2M - 0xe020_0000 0xe02f_ffff Empty 1M - 0xe030_0000 0xe03f_ffff PCI IO 1M - 0xe040_0000 0xefff_ffff Empty 252M - 0xf400_0000 0xf7ff_ffff Empty 64M - 0xf800_0000 0xf800_7fff BCSR on CS1 32K - 0xf800_8000 0xf800_ffff PIB CS2 32K - 0xf801_0000 0xf801_7fff PIB CS3 32K - 0xfe00_0000 0xfeff_ffff FLASH on CS0 16M - - -3. Definitions - -3.1 Explanation of NEW definitions in: - - include/configs/MPC832XEPB.h - - CONFIG_MPC83xx MPC83xx family for MPC8349, MPC8360 and MPC832x - CONFIG_MPC832x MPC832x specific - CONFIG_MPC832XEMDS MPC832XEMDS board specific - -4. Compilation - - Assuming you're using BASH shell: - - export CROSS_COMPILE=your-cross-compile-prefix - cd u-boot - make distclean - make MPC832XEMDS_config - make - - MPC832x support PCI 33MHz and PCI 66MHz, to make u-boot support PCI: - - 1)Make sure the DIP SW support PCI mode as described in Section 1.1. - - 2)To Make U-Boot image support PCI 33MHz, use - Make MPC832XEMDS_HOST_33_config - - 3)To Make U-Boot image support PCI 66MHz, use - Make MPC832XEMDS_HOST_66M_config - -5. Downloading and Flashing Images - -5.0 Download over network: - - tftp 10000 u-boot.bin - -5.1 Reflash U-boot Image using U-boot - - tftp 20000 u-boot.bin - protect off fe000000 fe0fffff - erase fe000000 fe0fffff - cp.b 20000 fe000000 xxxx - -You have to supply the correct byte count with 'xxxx' from the TFTP result log. -Maybe 3ffff will work too, that corresponds to the erased sectors. - - -6. Notes - 1) The console baudrate for MPC832XEMDS is 115200bps. diff --git a/qemu/roms/u-boot/board/freescale/mpc832xemds/mpc832xemds.c b/qemu/roms/u-boot/board/freescale/mpc832xemds/mpc832xemds.c deleted file mode 100644 index b7ea0e44c..000000000 --- a/qemu/roms/u-boot/board/freescale/mpc832xemds/mpc832xemds.c +++ /dev/null @@ -1,164 +0,0 @@ -/* - * Copyright (C) 2006 Freescale Semiconductor, Inc. - * - * Dave Liu <daveliu@freescale.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <ioports.h> -#include <mpc83xx.h> -#include <i2c.h> -#include <miiphy.h> -#include <command.h> -#if defined(CONFIG_PCI) -#include <pci.h> -#endif -#include <asm/mmu.h> -#if defined(CONFIG_OF_LIBFDT) -#include <libfdt.h> -#endif -#if defined(CONFIG_PQ_MDS_PIB) -#include "../common/pq-mds-pib.h" -#endif - -const qe_iop_conf_t qe_iop_conf_tab[] = { - /* ETH3 */ - {1, 0, 1, 0, 1}, /* TxD0 */ - {1, 1, 1, 0, 1}, /* TxD1 */ - {1, 2, 1, 0, 1}, /* TxD2 */ - {1, 3, 1, 0, 1}, /* TxD3 */ - {1, 9, 1, 0, 1}, /* TxER */ - {1, 12, 1, 0, 1}, /* TxEN */ - {3, 24, 2, 0, 1}, /* TxCLK->CLK10 */ - - {1, 4, 2, 0, 1}, /* RxD0 */ - {1, 5, 2, 0, 1}, /* RxD1 */ - {1, 6, 2, 0, 1}, /* RxD2 */ - {1, 7, 2, 0, 1}, /* RxD3 */ - {1, 8, 2, 0, 1}, /* RxER */ - {1, 10, 2, 0, 1}, /* RxDV */ - {0, 13, 2, 0, 1}, /* RxCLK->CLK9 */ - {1, 11, 2, 0, 1}, /* COL */ - {1, 13, 2, 0, 1}, /* CRS */ - - /* ETH4 */ - {1, 18, 1, 0, 1}, /* TxD0 */ - {1, 19, 1, 0, 1}, /* TxD1 */ - {1, 20, 1, 0, 1}, /* TxD2 */ - {1, 21, 1, 0, 1}, /* TxD3 */ - {1, 27, 1, 0, 1}, /* TxER */ - {1, 30, 1, 0, 1}, /* TxEN */ - {3, 6, 2, 0, 1}, /* TxCLK->CLK8 */ - - {1, 22, 2, 0, 1}, /* RxD0 */ - {1, 23, 2, 0, 1}, /* RxD1 */ - {1, 24, 2, 0, 1}, /* RxD2 */ - {1, 25, 2, 0, 1}, /* RxD3 */ - {1, 26, 1, 0, 1}, /* RxER */ - {1, 28, 2, 0, 1}, /* Rx_DV */ - {3, 31, 2, 0, 1}, /* RxCLK->CLK7 */ - {1, 29, 2, 0, 1}, /* COL */ - {1, 31, 2, 0, 1}, /* CRS */ - - {3, 4, 3, 0, 2}, /* MDIO */ - {3, 5, 1, 0, 2}, /* MDC */ - - {0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */ -}; - -int board_early_init_f(void) -{ - volatile u8 *bcsr = (volatile u8 *)CONFIG_SYS_BCSR; - - /* Enable flash write */ - bcsr[9] &= ~0x08; - - return 0; -} - -int board_early_init_r(void) -{ -#ifdef CONFIG_PQ_MDS_PIB - pib_init(); -#endif - return 0; -} - -int fixed_sdram(void); - -phys_size_t initdram(int board_type) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - u32 msize = 0; - - if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im) - return -1; - - /* DDR SDRAM - Main SODIMM */ - im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR; - - msize = fixed_sdram(); - - /* return total bus SDRAM size(bytes) -- DDR */ - return (msize * 1024 * 1024); -} - -/************************************************************************* - * fixed sdram init -- doesn't use serial presence detect. - ************************************************************************/ -int fixed_sdram(void) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - u32 msize = 0; - u32 ddr_size; - u32 ddr_size_log2; - - msize = CONFIG_SYS_DDR_SIZE; - for (ddr_size = msize << 20, ddr_size_log2 = 0; - (ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) { - if (ddr_size & 1) { - return -1; - } - } - im->sysconf.ddrlaw[0].ar = - LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE); -#if (CONFIG_SYS_DDR_SIZE != 128) -#warning Currenly any ddr size other than 128 is not supported -#endif - im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CNTL; - im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS; - im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG; - im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0; - im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1; - im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2; - im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3; - im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG; - im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2; - im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE; - im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2; - im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL; - __asm__ __volatile__ ("sync"); - udelay(200); - - im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; - __asm__ __volatile__ ("sync"); - return msize; -} - -int checkboard(void) -{ - puts("Board: Freescale MPC832XEMDS\n"); - return 0; -} - -#if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) -{ - ft_cpu_setup(blob, bd); -#ifdef CONFIG_PCI - ft_pci_setup(blob, bd); -#endif -} -#endif diff --git a/qemu/roms/u-boot/board/freescale/mpc832xemds/pci.c b/qemu/roms/u-boot/board/freescale/mpc832xemds/pci.c deleted file mode 100644 index e8b2b11d8..000000000 --- a/qemu/roms/u-boot/board/freescale/mpc832xemds/pci.c +++ /dev/null @@ -1,146 +0,0 @@ -/* - * Copyright (C) 2006-2009 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * PCI Configuration space access support for MPC83xx PCI Bridge - */ -#include <asm/mmu.h> -#include <asm/io.h> -#include <common.h> -#include <mpc83xx.h> -#include <pci.h> -#include <i2c.h> -#include <asm/fsl_i2c.h> -#include "../common/pq-mds-pib.h" - -DECLARE_GLOBAL_DATA_PTR; - -static struct pci_region pci1_regions[] = { - { - bus_start: CONFIG_SYS_PCI1_MEM_BASE, - phys_start: CONFIG_SYS_PCI1_MEM_PHYS, - size: CONFIG_SYS_PCI1_MEM_SIZE, - flags: PCI_REGION_MEM | PCI_REGION_PREFETCH - }, - { - bus_start: CONFIG_SYS_PCI1_IO_BASE, - phys_start: CONFIG_SYS_PCI1_IO_PHYS, - size: CONFIG_SYS_PCI1_IO_SIZE, - flags: PCI_REGION_IO - }, - { - bus_start: CONFIG_SYS_PCI1_MMIO_BASE, - phys_start: CONFIG_SYS_PCI1_MMIO_PHYS, - size: CONFIG_SYS_PCI1_MMIO_SIZE, - flags: PCI_REGION_MEM - }, -}; - -#ifdef CONFIG_MPC83XX_PCI2 -static struct pci_region pci2_regions[] = { - { - bus_start: CONFIG_SYS_PCI2_MEM_BASE, - phys_start: CONFIG_SYS_PCI2_MEM_PHYS, - size: CONFIG_SYS_PCI2_MEM_SIZE, - flags: PCI_REGION_MEM | PCI_REGION_PREFETCH - }, - { - bus_start: CONFIG_SYS_PCI2_IO_BASE, - phys_start: CONFIG_SYS_PCI2_IO_PHYS, - size: CONFIG_SYS_PCI2_IO_SIZE, - flags: PCI_REGION_IO - }, - { - bus_start: CONFIG_SYS_PCI2_MMIO_BASE, - phys_start: CONFIG_SYS_PCI2_MMIO_PHYS, - size: CONFIG_SYS_PCI2_MMIO_SIZE, - flags: PCI_REGION_MEM - }, -}; -#endif - -void pci_init_board(void) -#ifdef CONFIG_PCISLAVE -{ - volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR; - volatile law83xx_t *pci_law = immr->sysconf.pcilaw; - volatile pcictrl83xx_t *pci_ctrl = &immr->pci_ctrl[0]; - struct pci_region *reg[] = { pci1_regions }; - - /* Configure PCI Local Access Windows */ - pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR; - pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G; - - pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR; - pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M; - - mpc83xx_pci_init(1, reg); - - /* - * Configure PCI Inbound Translation Windows - */ - pci_ctrl[0].pitar0 = 0x0; - pci_ctrl[0].pibar0 = 0x0; - pci_ctrl[0].piwar0 = PIWAR_EN | PIWAR_RTT_SNOOP | - PIWAR_WTT_SNOOP | PIWAR_IWS_4K; - - pci_ctrl[0].pitar1 = 0x0; - pci_ctrl[0].pibar1 = 0x0; - pci_ctrl[0].piebar1 = 0x0; - pci_ctrl[0].piwar1 &= ~PIWAR_EN; - - pci_ctrl[0].pitar2 = 0x0; - pci_ctrl[0].pibar2 = 0x0; - pci_ctrl[0].piebar2 = 0x0; - pci_ctrl[0].piwar2 &= ~PIWAR_EN; - - /* Unlock the configuration bit */ - mpc83xx_pcislave_unlock(0); - printf("PCI: Agent mode enabled\n"); -} -#else -{ - volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR; - volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk; - volatile law83xx_t *pci_law = immr->sysconf.pcilaw; -#ifndef CONFIG_MPC83XX_PCI2 - struct pci_region *reg[] = { pci1_regions }; -#else - struct pci_region *reg[] = { pci1_regions, pci2_regions }; -#endif - - /* initialize the PCA9555PW IO expander on the PIB board */ - pib_init(); - -#if defined(CONFIG_PCI_66M) - clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2; - printf("PCI clock is 66MHz\n"); -#elif defined(CONFIG_PCI_33M) - clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2 | - OCCR_PCICD0 | OCCR_PCICD1 | OCCR_PCICD2 | OCCR_PCICR; - printf("PCI clock is 33MHz\n"); -#else - clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2; - printf("PCI clock is 66MHz\n"); -#endif - udelay(2000); - - /* Configure PCI Local Access Windows */ - pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR; - pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_512M; - - pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR; - pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_1M; - - udelay(2000); - -#ifndef CONFIG_MPC83XX_PCI2 - mpc83xx_pci_init(1, reg); -#else - mpc83xx_pci_init(2, reg); -#endif -} -#endif /* CONFIG_PCISLAVE */ |