diff options
Diffstat (limited to 'qemu/roms/u-boot/board/csb272/init.S')
| -rw-r--r-- | qemu/roms/u-boot/board/csb272/init.S | 196 |
1 files changed, 0 insertions, 196 deletions
diff --git a/qemu/roms/u-boot/board/csb272/init.S b/qemu/roms/u-boot/board/csb272/init.S deleted file mode 100644 index bf1d98680..000000000 --- a/qemu/roms/u-boot/board/csb272/init.S +++ /dev/null @@ -1,196 +0,0 @@ -/* - * SPDX-License-Identifier: GPL-2.0 IBM-pibs - */ -#include <config.h> -#include <asm/ppc4xx.h> - -#include <ppc_asm.tmpl> -#include <ppc_defs.h> - -#include <asm/cache.h> -#include <asm/mmu.h> - -#define LI32(reg,val) \ - addis reg,0,val@h;\ - ori reg,reg,val@l - -#define WDCR_EBC(reg,val) \ - addi r4,0,reg;\ - mtdcr EBC0_CFGADDR,r4;\ - addis r4,0,val@h;\ - ori r4,r4,val@l;\ - mtdcr EBC0_CFGDATA,r4 - -#define WDCR_SDRAM(reg,val) \ - addi r4,0,reg;\ - mtdcr SDRAM0_CFGADDR,r4;\ - addis r4,0,val@h;\ - ori r4,r4,val@l;\ - mtdcr SDRAM0_CFGDATA,r4 - -/****************************************************************************** - * Function: ext_bus_cntlr_init - * - * Description: Configures EBC Controller and a few basic chip selects. - * - * CS0 is setup to get the Boot Flash out of the addresss range - * so that we may setup a stack. CS7 is setup so that we can - * access and reset the hardware watchdog. - * - * IMPORTANT: For pass1 this code must run from - * cache since you can not reliably change a peripheral banks - * timing register (pbxap) while running code from that bank. - * For ex., since we are running from ROM on bank 0, we can NOT - * execute the code that modifies bank 0 timings from ROM, so - * we run it from cache. - * - * Notes: Does NOT use the stack. - *****************************************************************************/ - .section ".text" - .align 2 - .globl ext_bus_cntlr_init - .type ext_bus_cntlr_init, @function -ext_bus_cntlr_init: - mflr r0 - /******************************************************************** - * Prefetch entire ext_bus_cntrl_init function into the icache. - * This is necessary because we are going to change the same CS we - * are executing from. Otherwise a CPU lockup may occur. - *******************************************************************/ - bl ..getAddr -..getAddr: - mflr r3 /* get address of ..getAddr */ - - /* Calculate number of cache lines for this function */ - addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2) - mtctr r4 -..ebcloop: - icbt r0, r3 /* prefetch cache line for addr in r3*/ - addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */ - bdnz ..ebcloop /* continue for $CTR cache lines */ - - /******************************************************************** - * Delay to ensure all accesses to ROM are complete before changing - * bank 0 timings. 200usec should be enough. - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles. - *******************************************************************/ - addis r3, 0, 0x0 - ori r3, r3, 0xA000 /* wait 200us from reset */ - mtctr r3 -..spinlp: - bdnz ..spinlp /* spin loop */ - - /******************************************************************** - * SETUP CPC0_CR0 - *******************************************************************/ - LI32(r4, 0x007000c0) - mtdcr CPC0_CR0, r4 - - /******************************************************************** - * Setup CPC0_CR1: Change PCIINT signal to PerWE - *******************************************************************/ - mfdcr r4, CPC0_CR1 - ori r4, r4, 0x4000 - mtdcr CPC0_CR1, r4 - - /******************************************************************** - * Setup External Bus Controller (EBC). - *******************************************************************/ - WDCR_EBC(EBC0_CFG, 0xd84c0000) - /******************************************************************** - * Memory Bank 0 (Intel 28F128J3 Flash) initialization - *******************************************************************/ - /*WDCR_EBC(PB1AP, 0x02869200)*/ - WDCR_EBC(PB1AP, 0x07869200) - WDCR_EBC(PB0CR, 0xfe0bc000) - /******************************************************************** - * Memory Bank 1 (Holtek HT6542B PS/2) initialization - *******************************************************************/ - WDCR_EBC(PB1AP, 0x1f869200) - WDCR_EBC(PB1CR, 0xf0818000) - /******************************************************************** - * Memory Bank 2 (Epson S1D13506) initialization - *******************************************************************/ - WDCR_EBC(PB2AP, 0x05860300) - WDCR_EBC(PB2CR, 0xf045a000) - /******************************************************************** - * Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization - *******************************************************************/ - WDCR_EBC(PB3AP, 0x0387d200) - WDCR_EBC(PB3CR, 0xf021c000) - /******************************************************************** - * Memory Bank 4-7 (Unused) initialization - *******************************************************************/ - WDCR_EBC(PB4AP, 0) - WDCR_EBC(PB4CR, 0) - WDCR_EBC(PB5AP, 0) - WDCR_EBC(PB5CR, 0) - WDCR_EBC(PB6AP, 0) - WDCR_EBC(PB6CR, 0) - WDCR_EBC(PB7AP, 0) - WDCR_EBC(PB7CR, 0) - - /* We are all done */ - mtlr r0 /* Restore link register */ - blr /* Return to calling function */ -.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init -/* end ext_bus_cntlr_init() */ - -/****************************************************************************** - * Function: sdram_init - * - * Description: Configures SDRAM memory banks. - * - * Notes: Does NOT use the stack. - *****************************************************************************/ - .section ".text" - .align 2 - .globl sdram_init - .type sdram_init, @function -sdram_init: - - /* - * Disable memory controller to allow - * values to be changed. - */ - WDCR_SDRAM(SDRAM0_CFG, 0x00000000) - - /* - * Configure Memory Banks - */ - WDCR_SDRAM(SDRAM0_B0CR, 0x00084001) - WDCR_SDRAM(SDRAM0_B1CR, 0x00000000) - WDCR_SDRAM(SDRAM0_B2CR, 0x00000000) - WDCR_SDRAM(SDRAM0_B3CR, 0x00000000) - - /* - * Set up SDTR1 (SDRAM Timing Register) - */ - WDCR_SDRAM(SDRAM0_TR, 0x00854009) - - /* - * Set RTR (Refresh Timing Register) - */ - WDCR_SDRAM(SDRAM0_RTR, 0x10000000) - /* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */ - - /******************************************************************** - * Delay to ensure 200usec have elapsed since reset. Assume worst - * case that the core is running 200Mhz: - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles - *******************************************************************/ - addis r3, 0, 0x0000 - ori r3, r3, 0xA000 /* Wait >200us from reset */ - mtctr r3 -..spinlp2: - bdnz ..spinlp2 /* spin loop */ - - /******************************************************************** - * Set memory controller options reg, MCOPT1. - *******************************************************************/ - WDCR_SDRAM(SDRAM0_CFG,0x80800000) - -..sdri_done: - blr /* Return to calling function */ -.Lfe1: .size sdram_init,.Lfe1-sdram_init -/* end sdram_init() */ |