1 files changed, 0 insertions, 133 deletions
diff --git a/qemu/roms/u-boot/board/Marvell/sheevaplug/sheevaplug.c b/qemu/roms/u-boot/board/Marvell/sheevaplug/sheevaplug.c
deleted file mode 100644
index 87e49f417..000000000
--- a/qemu/roms/u-boot/board/Marvell/sheevaplug/sheevaplug.c
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/kirkwood.h>
-#include <asm/arch/mpp.h>
-#include "sheevaplug.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/*
-	 * default gpio configuration
-	 * There are maximum 64 gpios controlled through 2 sets of registers
-	 * the  below configuration configures mainly initial LED status
-	 */
-	kw_config_gpio(SHEEVAPLUG_OE_VAL_LOW,
-			SHEEVAPLUG_OE_VAL_HIGH,
-			SHEEVAPLUG_OE_LOW, SHEEVAPLUG_OE_HIGH);
-
-	/* Multi-Purpose Pins Functionality configuration */
-	static const u32 kwmpp_config[] = {
-		MPP0_NF_IO2,
-		MPP1_NF_IO3,
-		MPP2_NF_IO4,
-		MPP3_NF_IO5,
-		MPP4_NF_IO6,
-		MPP5_NF_IO7,
-		MPP6_SYSRST_OUTn,
-		MPP7_GPO,
-		MPP8_UART0_RTS,
-		MPP9_UART0_CTS,
-		MPP10_UART0_TXD,
-		MPP11_UART0_RXD,
-		MPP12_SD_CLK,
-		MPP13_SD_CMD,
-		MPP14_SD_D0,
-		MPP15_SD_D1,
-		MPP16_SD_D2,
-		MPP17_SD_D3,
-		MPP18_NF_IO0,
-		MPP19_NF_IO1,
-		MPP20_GPIO,
-		MPP21_GPIO,
-		MPP22_GPIO,
-		MPP23_GPIO,
-		MPP24_GPIO,
-		MPP25_GPIO,
-		MPP26_GPIO,
-		MPP27_GPIO,
-		MPP28_GPIO,
-		MPP29_TSMP9,
-		MPP30_GPIO,
-		MPP31_GPIO,
-		MPP32_GPIO,
-		MPP33_GPIO,
-		MPP34_GPIO,
-		MPP35_GPIO,
-		MPP36_GPIO,
-		MPP37_GPIO,
-		MPP38_GPIO,
-		MPP39_GPIO,
-		MPP40_GPIO,
-		MPP41_GPIO,
-		MPP42_GPIO,
-		MPP43_GPIO,
-		MPP44_GPIO,
-		MPP45_GPIO,
-		MPP46_GPIO,
-		MPP47_GPIO,
-		MPP48_GPIO,
-		MPP49_GPIO,
-		0
-	};
-	kirkwood_mpp_conf(kwmpp_config, NULL);
-	return 0;
-}
-
-int board_init(void)
-{
-	/*
-	 * arch number of board
-	 */
-	gd->bd->bi_arch_number = MACH_TYPE_SHEEVAPLUG;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
-
-	return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116 PHY */
-void reset_phy(void)
-{
-	u16 reg;
-	u16 devadr;
-	char *name = "egiga0";
-
-	if (miiphy_set_current_dev(name))
-		return;
-
-	/* command to read PHY dev address */
-	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
-		printf("Err..%s could not read PHY dev address\n",
-			__FUNCTION__);
-		return;
-	}
-
-	/*
-	 * Enable RGMII delay on Tx and Rx for CPU port
-	 * Ref: sec 4.7.2 of chip datasheet
-	 */
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
-	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
-	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
-	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
-	/* reset the phy */
-	miiphy_reset(name, devadr);
-
-	printf("88E1116 Initialized on %s\n", name);
-}
-#endif /* CONFIG_RESET_PHY_R */