diff options
Diffstat (limited to 'qemu/roms/u-boot/board/Marvell/rd6281a/rd6281a.c')
| -rw-r--r-- | qemu/roms/u-boot/board/Marvell/rd6281a/rd6281a.c | 157 |
1 files changed, 157 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/Marvell/rd6281a/rd6281a.c b/qemu/roms/u-boot/board/Marvell/rd6281a/rd6281a.c new file mode 100644 index 000000000..33ef0c78e --- /dev/null +++ b/qemu/roms/u-boot/board/Marvell/rd6281a/rd6281a.c @@ -0,0 +1,157 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <miiphy.h> +#include <netdev.h> +#include <asm/arch/cpu.h> +#include <asm/arch/kirkwood.h> +#include <asm/arch/mpp.h> +#include "rd6281a.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + kw_config_gpio(RD6281A_OE_VAL_LOW, + RD6281A_OE_VAL_HIGH, + RD6281A_OE_LOW, RD6281A_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + static const u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_SD_CLK, + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, + MPP29_GPIO, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GE1_14, + MPP35_GPIO, + MPP36_AUDIO_SPDIFI, + MPP37_AUDIO_SPDIFO, + MPP38_GPIO, + MPP39_TDM_SPI_CS0, + MPP40_TDM_SPI_SCK, + MPP41_TDM_SPI_MISO, + MPP42_TDM_SPI_MOSI, + MPP43_TDM_CODEC_INTn, + MPP44_GPIO, + MPP45_TDM_PCLK, + MPP46_TDM_FS, + MPP47_TDM_DRX, + MPP48_TDM_DTX, + MPP49_GPIO, + 0 + }; + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ + /* + * arch number of board + */ + gd->bd->bi_arch_number = MACH_TYPE_RD88F6281; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + + return 0; +} + +void mv_phy_88e1116_init(char *name) +{ + u16 reg; + u16 devadr; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { + printf("Err..%s could not read PHY dev address\n", + __FUNCTION__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); + + /* reset the phy */ + if (miiphy_read (name, devadr, MII_BMCR, ®) != 0) { + printf("Err..(%s) PHY status read failed\n", __FUNCTION__); + return; + } + if (miiphy_write (name, devadr, MII_BMCR, reg | 0x8000) != 0) { + printf("Err..(%s) PHY reset failed\n", __FUNCTION__); + return; + } + + printf("88E1116 Initialized on %s\n", name); +} + +/* Configure and enable Switch and PHY */ +void reset_phy(void) +{ + /* configure and initialize switch */ + struct mv88e61xx_config swcfg = { + .name = "egiga0", + .vlancfg = MV88E61XX_VLANCFG_ROUTER, + .rgmii_delay = MV88E61XX_RGMII_DELAY_EN, + .led_init = MV88E61XX_LED_INIT_EN, + .portstate = MV88E61XX_PORTSTT_FORWARDING, + .cpuport = (1 << 5), + .ports_enabled = 0x3f, + }; + + mv88e61xx_switch_initialize(&swcfg); + + /* configure and initialize PHY */ + mv_phy_88e1116_init("egiga1"); +} |