diff options
Diffstat (limited to 'qemu/roms/ipxe/src/include/ipxe/spi.h')
| -rw-r--r-- | qemu/roms/ipxe/src/include/ipxe/spi.h | 258 |
1 files changed, 0 insertions, 258 deletions
diff --git a/qemu/roms/ipxe/src/include/ipxe/spi.h b/qemu/roms/ipxe/src/include/ipxe/spi.h deleted file mode 100644 index 83b53bce3..000000000 --- a/qemu/roms/ipxe/src/include/ipxe/spi.h +++ /dev/null @@ -1,258 +0,0 @@ -#ifndef _IPXE_SPI_H -#define _IPXE_SPI_H - -/** @file - * - * SPI interface - * - */ - -FILE_LICENCE ( GPL2_OR_LATER_OR_UBDL ); - -#include <ipxe/nvs.h> - -/** - * @defgroup spicmds SPI commands - * @{ - */ - -/** Write status register */ -#define SPI_WRSR 0x01 - -/** Write data to memory array */ -#define SPI_WRITE 0x02 - -/** Read data from memory array */ -#define SPI_READ 0x03 - -/** Reset write enable latch */ -#define SPI_WRDI 0x04 - -/** Read status register */ -#define SPI_RDSR 0x05 - -/** Set write enable latch */ -#define SPI_WREN 0x06 - -/** - * @defgroup atmelcmds Atmel-specific SPI commands - * @{ - */ - -/** Erase one sector in memory array (Not supported on all devices) */ -#define ATMEL_SECTOR_ERASE 0x52 - -/** Erase all sections in memory array (Not supported on all devices) */ -#define ATMEL_CHIP_ERASE 0x62 - -/** Read manufacturer and product ID (Not supported on all devices) */ -#define ATMEL_RDID 0x15 - -/** @} */ - -/** @} */ - -/** - * @defgroup spistatus SPI status register bits (not present on all devices) - * @{ - */ - -/** Write-protect pin enabled */ -#define SPI_STATUS_WPEN 0x80 - -/** Block protection bit 2 */ -#define SPI_STATUS_BP2 0x10 - -/** Block protection bit 1 */ -#define SPI_STATUS_BP1 0x08 - -/** Block protection bit 0 */ -#define SPI_STATUS_BP0 0x04 - -/** State of the write enable latch */ -#define SPI_STATUS_WEN 0x02 - -/** Device busy flag */ -#define SPI_STATUS_NRDY 0x01 - -/** @} */ - -/** - * An SPI device - * - * This data structure represents a physical SPI device attached to an - * SPI bus. - */ -struct spi_device { - /** NVS device */ - struct nvs_device nvs; - /** SPI bus to which device is attached */ - struct spi_bus *bus; - /** Slave number */ - unsigned int slave; - /** Command length, in bits */ - unsigned int command_len; - /** Address length, in bits */ - unsigned int address_len; - /** Address is munged - * - * Some devices with 9-bit addresses (e.g. AT25040A EEPROM) - * use bit 3 of the command byte as address bit A8, rather - * than having a two-byte address. If this flag is set, then - * commands should be munged in this way. - */ - unsigned int munge_address : 1; -}; - -/** - * SPI magic autodetection address length - * - * Set @c spi_device::address_len to @c SPI_AUTODETECT_ADDRESS_LEN if - * the address length should be autodetected. - */ -#define SPI_AUTODETECT_ADDRESS_LEN 0 - -static inline __attribute__ (( always_inline )) struct spi_device * -nvs_to_spi ( struct nvs_device *nvs ) { - return container_of ( nvs, struct spi_device, nvs ); -} - -/** - * An SPI bus - * - * This data structure represents an SPI bus controller capable of - * issuing commands to attached SPI devices. - */ -struct spi_bus { - /** SPI interface mode - * - * This is the bitwise OR of zero or more of @c SPI_MODE_CPHA - * and @c SPI_MODE_CPOL. It is also the number conventionally - * used to describe the SPI interface mode. For example, SPI - * mode 1 is the mode in which CPOL=0 and CPHA=1, which - * therefore corresponds to a mode value of (0|SPI_MODE_CPHA) - * which, happily, equals 1. - */ - unsigned int mode; - /** - * Read/write data via SPI bus - * - * @v bus SPI bus - * @v device SPI device - * @v command Command - * @v address Address to read/write (<0 for no address) - * @v data_out TX data buffer (or NULL) - * @v data_in RX data buffer (or NULL) - * @v len Length of data buffer(s) - * - * This issues the specified command and optional address to - * the SPI device, then reads and/or writes data to/from the - * data buffers. - */ - int ( * rw ) ( struct spi_bus *bus, struct spi_device *device, - unsigned int command, int address, - const void *data_out, void *data_in, size_t len ); -}; - -/** Clock phase (CPHA) mode bit - * - * Phase 0 is sample on rising edge, shift data on falling edge. - * - * Phase 1 is shift data on rising edge, sample data on falling edge. - */ -#define SPI_MODE_CPHA 0x01 - -/** Clock polarity (CPOL) mode bit - * - * This bit reflects the idle state of the clock line (SCLK). - */ -#define SPI_MODE_CPOL 0x02 - -/** Slave select polarity mode bit - * - * This bit reflects that active state of the slave select lines. It - * is not part of the normal SPI mode number (which covers only @c - * SPI_MODE_CPOL and @c SPI_MODE_CPHA), but is included here for - * convenience. - */ -#define SPI_MODE_SSPOL 0x10 - -/** Microwire-compatible mode - * - * This is SPI mode 1 (i.e. CPOL=0, CPHA=1), and is compatible with - * the original Microwire protocol. - */ -#define SPI_MODE_MICROWIRE 1 - -/** Microwire/Plus-compatible mode - * - * This is SPI mode 0 (i.e. CPOL=0, CPHA=0), and is compatible with - * the Microwire/Plus protocol - */ -#define SPI_MODE_MICROWIRE_PLUS 0 - -/** Threewire-compatible mode - * - * This mode is compatible with Atmel's series of "three-wire" - * interfaces. - */ -#define SPI_MODE_THREEWIRE ( SPI_MODE_MICROWIRE_PLUS | SPI_MODE_SSPOL ) - -extern int spi_read ( struct nvs_device *nvs, unsigned int address, - void *data, size_t len ); -extern int spi_write ( struct nvs_device *nvs, unsigned int address, - const void *data, size_t len ); - -/** - * @defgroup spidevs SPI device types - * @{ - */ - -static inline __attribute__ (( always_inline )) void -init_spi ( struct spi_device *device ) { - device->nvs.word_len_log2 = 0; - device->command_len = 8, - device->nvs.read = spi_read; - device->nvs.write = spi_write; -} - -/** Atmel AT25F1024 serial flash */ -static inline __attribute__ (( always_inline )) void -init_at25f1024 ( struct spi_device *device ) { - device->address_len = 24; - device->nvs.size = ( 128 * 1024 ); - device->nvs.block_size = 256; - init_spi ( device ); -} - -/** Atmel 25040 serial EEPROM */ -static inline __attribute__ (( always_inline )) void -init_at25040 ( struct spi_device *device ) { - device->address_len = 8; - device->munge_address = 1; - device->nvs.size = 512; - device->nvs.block_size = 8; - init_spi ( device ); -} - -/** ST M25P32 serial flash */ -static inline __attribute__ (( always_inline )) void -init_m25p32 ( struct spi_device *device ) { - device->address_len = 24; - device->nvs.size = ( 4 * 1024 * 1024 ); - device->nvs.block_size = 256; - init_spi ( device ); -} - -/** Microchip 25XX640 serial EEPROM */ -static inline __attribute__ (( always_inline )) void -init_mc25xx640 ( struct spi_device *device ) { - device->address_len = 16; - device->nvs.size = ( 8 * 1024 ); - device->nvs.block_size = 32; - init_spi ( device ); -} - -/** @} */ - -#endif /* _IPXE_SPI_H */ |