diff options
Diffstat (limited to 'kernel/include/linux/spi')
33 files changed, 2404 insertions, 0 deletions
diff --git a/kernel/include/linux/spi/ad7877.h b/kernel/include/linux/spi/ad7877.h new file mode 100644 index 000000000..cdbed816f --- /dev/null +++ b/kernel/include/linux/spi/ad7877.h @@ -0,0 +1,24 @@ +/* linux/spi/ad7877.h */ + +/* Touchscreen characteristics vary between boards and models. The + * platform_data for the device's "struct device" holds this information. + * + * It's OK if the min/max values are zero. + */ +struct ad7877_platform_data { + u16 model; /* 7877 */ + u16 vref_delay_usecs; /* 0 for external vref; etc */ + u16 x_plate_ohms; + u16 y_plate_ohms; + + u16 x_min, x_max; + u16 y_min, y_max; + u16 pressure_min, pressure_max; + + u8 stopacq_polarity; /* 1 = Active HIGH, 0 = Active LOW */ + u8 first_conversion_delay; /* 0 = 0.5us, 1 = 128us, 2 = 1ms, 3 = 8ms */ + u8 acquisition_time; /* 0 = 2us, 1 = 4us, 2 = 8us, 3 = 16us */ + u8 averaging; /* 0 = 1, 1 = 4, 2 = 8, 3 = 16 */ + u8 pen_down_acc_interval; /* 0 = covert once, 1 = every 0.5 ms, + 2 = ever 1 ms, 3 = every 8 ms,*/ +}; diff --git a/kernel/include/linux/spi/ad7879.h b/kernel/include/linux/spi/ad7879.h new file mode 100644 index 000000000..58368be0b --- /dev/null +++ b/kernel/include/linux/spi/ad7879.h @@ -0,0 +1,41 @@ +/* linux/spi/ad7879.h */ + +/* Touchscreen characteristics vary between boards and models. The + * platform_data for the device's "struct device" holds this information. + * + * It's OK if the min/max values are zero. + */ +struct ad7879_platform_data { + u16 model; /* 7879 */ + u16 x_plate_ohms; + u16 x_min, x_max; + u16 y_min, y_max; + u16 pressure_min, pressure_max; + + bool swap_xy; /* swap x and y axes */ + + /* [0..255] 0=OFF Starts at 1=550us and goes + * all the way to 9.440ms in steps of 35us. + */ + u8 pen_down_acc_interval; + /* [0..15] Starts at 0=128us and goes all the + * way to 4.096ms in steps of 128us. + */ + u8 first_conversion_delay; + /* [0..3] 0 = 2us, 1 = 4us, 2 = 8us, 3 = 16us */ + u8 acquisition_time; + /* [0..3] Average X middle samples 0 = 2, 1 = 4, 2 = 8, 3 = 16 */ + u8 averaging; + /* [0..3] Perform X measurements 0 = OFF, + * 1 = 4, 2 = 8, 3 = 16 (median > averaging) + */ + u8 median; + /* 1 = AUX/VBAT/GPIO export GPIO to gpiolib + * requires CONFIG_GPIOLIB + */ + bool gpio_export; + /* identifies the first GPIO number handled by this chip; + * or, if negative, requests dynamic ID allocation. + */ + s32 gpio_base; +}; diff --git a/kernel/include/linux/spi/adi_spi3.h b/kernel/include/linux/spi/adi_spi3.h new file mode 100644 index 000000000..c84123aa1 --- /dev/null +++ b/kernel/include/linux/spi/adi_spi3.h @@ -0,0 +1,254 @@ +/* + * Analog Devices SPI3 controller driver + * + * Copyright (c) 2014 Analog Devices Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _ADI_SPI3_H_ +#define _ADI_SPI3_H_ + +#include <linux/types.h> + +/* SPI_CONTROL */ +#define SPI_CTL_EN 0x00000001 /* Enable */ +#define SPI_CTL_MSTR 0x00000002 /* Master/Slave */ +#define SPI_CTL_PSSE 0x00000004 /* controls modf error in master mode */ +#define SPI_CTL_ODM 0x00000008 /* Open Drain Mode */ +#define SPI_CTL_CPHA 0x00000010 /* Clock Phase */ +#define SPI_CTL_CPOL 0x00000020 /* Clock Polarity */ +#define SPI_CTL_ASSEL 0x00000040 /* Slave Select Pin Control */ +#define SPI_CTL_SELST 0x00000080 /* Slave Select Polarity in-between transfers */ +#define SPI_CTL_EMISO 0x00000100 /* Enable MISO */ +#define SPI_CTL_SIZE 0x00000600 /* Word Transfer Size */ +#define SPI_CTL_SIZE08 0x00000000 /* SIZE: 8 bits */ +#define SPI_CTL_SIZE16 0x00000200 /* SIZE: 16 bits */ +#define SPI_CTL_SIZE32 0x00000400 /* SIZE: 32 bits */ +#define SPI_CTL_LSBF 0x00001000 /* LSB First */ +#define SPI_CTL_FCEN 0x00002000 /* Flow-Control Enable */ +#define SPI_CTL_FCCH 0x00004000 /* Flow-Control Channel Selection */ +#define SPI_CTL_FCPL 0x00008000 /* Flow-Control Polarity */ +#define SPI_CTL_FCWM 0x00030000 /* Flow-Control Water-Mark */ +#define SPI_CTL_FIFO0 0x00000000 /* FCWM: TFIFO empty or RFIFO Full */ +#define SPI_CTL_FIFO1 0x00010000 /* FCWM: TFIFO 75% or more empty or RFIFO 75% or more full */ +#define SPI_CTL_FIFO2 0x00020000 /* FCWM: TFIFO 50% or more empty or RFIFO 50% or more full */ +#define SPI_CTL_FMODE 0x00040000 /* Fast-mode Enable */ +#define SPI_CTL_MIOM 0x00300000 /* Multiple I/O Mode */ +#define SPI_CTL_MIO_DIS 0x00000000 /* MIOM: Disable */ +#define SPI_CTL_MIO_DUAL 0x00100000 /* MIOM: Enable DIOM (Dual I/O Mode) */ +#define SPI_CTL_MIO_QUAD 0x00200000 /* MIOM: Enable QUAD (Quad SPI Mode) */ +#define SPI_CTL_SOSI 0x00400000 /* Start on MOSI */ +/* SPI_RX_CONTROL */ +#define SPI_RXCTL_REN 0x00000001 /* Receive Channel Enable */ +#define SPI_RXCTL_RTI 0x00000004 /* Receive Transfer Initiate */ +#define SPI_RXCTL_RWCEN 0x00000008 /* Receive Word Counter Enable */ +#define SPI_RXCTL_RDR 0x00000070 /* Receive Data Request */ +#define SPI_RXCTL_RDR_DIS 0x00000000 /* RDR: Disabled */ +#define SPI_RXCTL_RDR_NE 0x00000010 /* RDR: RFIFO not empty */ +#define SPI_RXCTL_RDR_25 0x00000020 /* RDR: RFIFO 25% full */ +#define SPI_RXCTL_RDR_50 0x00000030 /* RDR: RFIFO 50% full */ +#define SPI_RXCTL_RDR_75 0x00000040 /* RDR: RFIFO 75% full */ +#define SPI_RXCTL_RDR_FULL 0x00000050 /* RDR: RFIFO full */ +#define SPI_RXCTL_RDO 0x00000100 /* Receive Data Over-Run */ +#define SPI_RXCTL_RRWM 0x00003000 /* FIFO Regular Water-Mark */ +#define SPI_RXCTL_RWM_0 0x00000000 /* RRWM: RFIFO Empty */ +#define SPI_RXCTL_RWM_25 0x00001000 /* RRWM: RFIFO 25% full */ +#define SPI_RXCTL_RWM_50 0x00002000 /* RRWM: RFIFO 50% full */ +#define SPI_RXCTL_RWM_75 0x00003000 /* RRWM: RFIFO 75% full */ +#define SPI_RXCTL_RUWM 0x00070000 /* FIFO Urgent Water-Mark */ +#define SPI_RXCTL_UWM_DIS 0x00000000 /* RUWM: Disabled */ +#define SPI_RXCTL_UWM_25 0x00010000 /* RUWM: RFIFO 25% full */ +#define SPI_RXCTL_UWM_50 0x00020000 /* RUWM: RFIFO 50% full */ +#define SPI_RXCTL_UWM_75 0x00030000 /* RUWM: RFIFO 75% full */ +#define SPI_RXCTL_UWM_FULL 0x00040000 /* RUWM: RFIFO full */ +/* SPI_TX_CONTROL */ +#define SPI_TXCTL_TEN 0x00000001 /* Transmit Channel Enable */ +#define SPI_TXCTL_TTI 0x00000004 /* Transmit Transfer Initiate */ +#define SPI_TXCTL_TWCEN 0x00000008 /* Transmit Word Counter Enable */ +#define SPI_TXCTL_TDR 0x00000070 /* Transmit Data Request */ +#define SPI_TXCTL_TDR_DIS 0x00000000 /* TDR: Disabled */ +#define SPI_TXCTL_TDR_NF 0x00000010 /* TDR: TFIFO not full */ +#define SPI_TXCTL_TDR_25 0x00000020 /* TDR: TFIFO 25% empty */ +#define SPI_TXCTL_TDR_50 0x00000030 /* TDR: TFIFO 50% empty */ +#define SPI_TXCTL_TDR_75 0x00000040 /* TDR: TFIFO 75% empty */ +#define SPI_TXCTL_TDR_EMPTY 0x00000050 /* TDR: TFIFO empty */ +#define SPI_TXCTL_TDU 0x00000100 /* Transmit Data Under-Run */ +#define SPI_TXCTL_TRWM 0x00003000 /* FIFO Regular Water-Mark */ +#define SPI_TXCTL_RWM_FULL 0x00000000 /* TRWM: TFIFO full */ +#define SPI_TXCTL_RWM_25 0x00001000 /* TRWM: TFIFO 25% empty */ +#define SPI_TXCTL_RWM_50 0x00002000 /* TRWM: TFIFO 50% empty */ +#define SPI_TXCTL_RWM_75 0x00003000 /* TRWM: TFIFO 75% empty */ +#define SPI_TXCTL_TUWM 0x00070000 /* FIFO Urgent Water-Mark */ +#define SPI_TXCTL_UWM_DIS 0x00000000 /* TUWM: Disabled */ +#define SPI_TXCTL_UWM_25 0x00010000 /* TUWM: TFIFO 25% empty */ +#define SPI_TXCTL_UWM_50 0x00020000 /* TUWM: TFIFO 50% empty */ +#define SPI_TXCTL_UWM_75 0x00030000 /* TUWM: TFIFO 75% empty */ +#define SPI_TXCTL_UWM_EMPTY 0x00040000 /* TUWM: TFIFO empty */ +/* SPI_CLOCK */ +#define SPI_CLK_BAUD 0x0000FFFF /* Baud Rate */ +/* SPI_DELAY */ +#define SPI_DLY_STOP 0x000000FF /* Transfer delay time in multiples of SCK period */ +#define SPI_DLY_LEADX 0x00000100 /* Extended (1 SCK) LEAD Control */ +#define SPI_DLY_LAGX 0x00000200 /* Extended (1 SCK) LAG control */ +/* SPI_SSEL */ +#define SPI_SLVSEL_SSE1 0x00000002 /* SPISSEL1 Enable */ +#define SPI_SLVSEL_SSE2 0x00000004 /* SPISSEL2 Enable */ +#define SPI_SLVSEL_SSE3 0x00000008 /* SPISSEL3 Enable */ +#define SPI_SLVSEL_SSE4 0x00000010 /* SPISSEL4 Enable */ +#define SPI_SLVSEL_SSE5 0x00000020 /* SPISSEL5 Enable */ +#define SPI_SLVSEL_SSE6 0x00000040 /* SPISSEL6 Enable */ +#define SPI_SLVSEL_SSE7 0x00000080 /* SPISSEL7 Enable */ +#define SPI_SLVSEL_SSEL1 0x00000200 /* SPISSEL1 Value */ +#define SPI_SLVSEL_SSEL2 0x00000400 /* SPISSEL2 Value */ +#define SPI_SLVSEL_SSEL3 0x00000800 /* SPISSEL3 Value */ +#define SPI_SLVSEL_SSEL4 0x00001000 /* SPISSEL4 Value */ +#define SPI_SLVSEL_SSEL5 0x00002000 /* SPISSEL5 Value */ +#define SPI_SLVSEL_SSEL6 0x00004000 /* SPISSEL6 Value */ +#define SPI_SLVSEL_SSEL7 0x00008000 /* SPISSEL7 Value */ +/* SPI_RWC */ +#define SPI_RWC_VALUE 0x0000FFFF /* Received Word-Count */ +/* SPI_RWCR */ +#define SPI_RWCR_VALUE 0x0000FFFF /* Received Word-Count Reload */ +/* SPI_TWC */ +#define SPI_TWC_VALUE 0x0000FFFF /* Transmitted Word-Count */ +/* SPI_TWCR */ +#define SPI_TWCR_VALUE 0x0000FFFF /* Transmitted Word-Count Reload */ +/* SPI_IMASK */ +#define SPI_IMSK_RUWM 0x00000002 /* Receive Urgent Water-Mark Interrupt Mask */ +#define SPI_IMSK_TUWM 0x00000004 /* Transmit Urgent Water-Mark Interrupt Mask */ +#define SPI_IMSK_ROM 0x00000010 /* Receive Over-Run Error Interrupt Mask */ +#define SPI_IMSK_TUM 0x00000020 /* Transmit Under-Run Error Interrupt Mask */ +#define SPI_IMSK_TCM 0x00000040 /* Transmit Collision Error Interrupt Mask */ +#define SPI_IMSK_MFM 0x00000080 /* Mode Fault Error Interrupt Mask */ +#define SPI_IMSK_RSM 0x00000100 /* Receive Start Interrupt Mask */ +#define SPI_IMSK_TSM 0x00000200 /* Transmit Start Interrupt Mask */ +#define SPI_IMSK_RFM 0x00000400 /* Receive Finish Interrupt Mask */ +#define SPI_IMSK_TFM 0x00000800 /* Transmit Finish Interrupt Mask */ +/* SPI_IMASKCL */ +#define SPI_IMSK_CLR_RUW 0x00000002 /* Receive Urgent Water-Mark Interrupt Mask */ +#define SPI_IMSK_CLR_TUWM 0x00000004 /* Transmit Urgent Water-Mark Interrupt Mask */ +#define SPI_IMSK_CLR_ROM 0x00000010 /* Receive Over-Run Error Interrupt Mask */ +#define SPI_IMSK_CLR_TUM 0x00000020 /* Transmit Under-Run Error Interrupt Mask */ +#define SPI_IMSK_CLR_TCM 0x00000040 /* Transmit Collision Error Interrupt Mask */ +#define SPI_IMSK_CLR_MFM 0x00000080 /* Mode Fault Error Interrupt Mask */ +#define SPI_IMSK_CLR_RSM 0x00000100 /* Receive Start Interrupt Mask */ +#define SPI_IMSK_CLR_TSM 0x00000200 /* Transmit Start Interrupt Mask */ +#define SPI_IMSK_CLR_RFM 0x00000400 /* Receive Finish Interrupt Mask */ +#define SPI_IMSK_CLR_TFM 0x00000800 /* Transmit Finish Interrupt Mask */ +/* SPI_IMASKST */ +#define SPI_IMSK_SET_RUWM 0x00000002 /* Receive Urgent Water-Mark Interrupt Mask */ +#define SPI_IMSK_SET_TUWM 0x00000004 /* Transmit Urgent Water-Mark Interrupt Mask */ +#define SPI_IMSK_SET_ROM 0x00000010 /* Receive Over-Run Error Interrupt Mask */ +#define SPI_IMSK_SET_TUM 0x00000020 /* Transmit Under-Run Error Interrupt Mask */ +#define SPI_IMSK_SET_TCM 0x00000040 /* Transmit Collision Error Interrupt Mask */ +#define SPI_IMSK_SET_MFM 0x00000080 /* Mode Fault Error Interrupt Mask */ +#define SPI_IMSK_SET_RSM 0x00000100 /* Receive Start Interrupt Mask */ +#define SPI_IMSK_SET_TSM 0x00000200 /* Transmit Start Interrupt Mask */ +#define SPI_IMSK_SET_RFM 0x00000400 /* Receive Finish Interrupt Mask */ +#define SPI_IMSK_SET_TFM 0x00000800 /* Transmit Finish Interrupt Mask */ +/* SPI_STATUS */ +#define SPI_STAT_SPIF 0x00000001 /* SPI Finished */ +#define SPI_STAT_RUWM 0x00000002 /* Receive Urgent Water-Mark Breached */ +#define SPI_STAT_TUWM 0x00000004 /* Transmit Urgent Water-Mark Breached */ +#define SPI_STAT_ROE 0x00000010 /* Receive Over-Run Error Indication */ +#define SPI_STAT_TUE 0x00000020 /* Transmit Under-Run Error Indication */ +#define SPI_STAT_TCE 0x00000040 /* Transmit Collision Error Indication */ +#define SPI_STAT_MODF 0x00000080 /* Mode Fault Error Indication */ +#define SPI_STAT_RS 0x00000100 /* Receive Start Indication */ +#define SPI_STAT_TS 0x00000200 /* Transmit Start Indication */ +#define SPI_STAT_RF 0x00000400 /* Receive Finish Indication */ +#define SPI_STAT_TF 0x00000800 /* Transmit Finish Indication */ +#define SPI_STAT_RFS 0x00007000 /* SPI_RFIFO status */ +#define SPI_STAT_RFIFO_EMPTY 0x00000000 /* RFS: RFIFO Empty */ +#define SPI_STAT_RFIFO_25 0x00001000 /* RFS: RFIFO 25% Full */ +#define SPI_STAT_RFIFO_50 0x00002000 /* RFS: RFIFO 50% Full */ +#define SPI_STAT_RFIFO_75 0x00003000 /* RFS: RFIFO 75% Full */ +#define SPI_STAT_RFIFO_FULL 0x00004000 /* RFS: RFIFO Full */ +#define SPI_STAT_TFS 0x00070000 /* SPI_TFIFO status */ +#define SPI_STAT_TFIFO_FULL 0x00000000 /* TFS: TFIFO full */ +#define SPI_STAT_TFIFO_25 0x00010000 /* TFS: TFIFO 25% empty */ +#define SPI_STAT_TFIFO_50 0x00020000 /* TFS: TFIFO 50% empty */ +#define SPI_STAT_TFIFO_75 0x00030000 /* TFS: TFIFO 75% empty */ +#define SPI_STAT_TFIFO_EMPTY 0x00040000 /* TFS: TFIFO empty */ +#define SPI_STAT_FCS 0x00100000 /* Flow-Control Stall Indication */ +#define SPI_STAT_RFE 0x00400000 /* SPI_RFIFO Empty */ +#define SPI_STAT_TFF 0x00800000 /* SPI_TFIFO Full */ +/* SPI_ILAT */ +#define SPI_ILAT_RUWMI 0x00000002 /* Receive Urgent Water Mark Interrupt */ +#define SPI_ILAT_TUWMI 0x00000004 /* Transmit Urgent Water Mark Interrupt */ +#define SPI_ILAT_ROI 0x00000010 /* Receive Over-Run Error Indication */ +#define SPI_ILAT_TUI 0x00000020 /* Transmit Under-Run Error Indication */ +#define SPI_ILAT_TCI 0x00000040 /* Transmit Collision Error Indication */ +#define SPI_ILAT_MFI 0x00000080 /* Mode Fault Error Indication */ +#define SPI_ILAT_RSI 0x00000100 /* Receive Start Indication */ +#define SPI_ILAT_TSI 0x00000200 /* Transmit Start Indication */ +#define SPI_ILAT_RFI 0x00000400 /* Receive Finish Indication */ +#define SPI_ILAT_TFI 0x00000800 /* Transmit Finish Indication */ +/* SPI_ILATCL */ +#define SPI_ILAT_CLR_RUWMI 0x00000002 /* Receive Urgent Water Mark Interrupt */ +#define SPI_ILAT_CLR_TUWMI 0x00000004 /* Transmit Urgent Water Mark Interrupt */ +#define SPI_ILAT_CLR_ROI 0x00000010 /* Receive Over-Run Error Indication */ +#define SPI_ILAT_CLR_TUI 0x00000020 /* Transmit Under-Run Error Indication */ +#define SPI_ILAT_CLR_TCI 0x00000040 /* Transmit Collision Error Indication */ +#define SPI_ILAT_CLR_MFI 0x00000080 /* Mode Fault Error Indication */ +#define SPI_ILAT_CLR_RSI 0x00000100 /* Receive Start Indication */ +#define SPI_ILAT_CLR_TSI 0x00000200 /* Transmit Start Indication */ +#define SPI_ILAT_CLR_RFI 0x00000400 /* Receive Finish Indication */ +#define SPI_ILAT_CLR_TFI 0x00000800 /* Transmit Finish Indication */ + +/* + * adi spi3 registers layout + */ +struct adi_spi_regs { + u32 revid; + u32 control; + u32 rx_control; + u32 tx_control; + u32 clock; + u32 delay; + u32 ssel; + u32 rwc; + u32 rwcr; + u32 twc; + u32 twcr; + u32 reserved0; + u32 emask; + u32 emaskcl; + u32 emaskst; + u32 reserved1; + u32 status; + u32 elat; + u32 elatcl; + u32 reserved2; + u32 rfifo; + u32 reserved3; + u32 tfifo; +}; + +#define MAX_CTRL_CS 8 /* cs in spi controller */ + +/* device.platform_data for SSP controller devices */ +struct adi_spi3_master { + u16 num_chipselect; + u16 pin_req[7]; +}; + +/* spi_board_info.controller_data for SPI slave devices, + * copied to spi_device.platform_data ... mostly for dma tuning + */ +struct adi_spi3_chip { + u32 control; + u16 cs_chg_udelay; /* Some devices require 16-bit delays */ + u32 tx_dummy_val; /* tx value for rx only transfer */ + bool enable_dma; +}; + +#endif /* _ADI_SPI3_H_ */ diff --git a/kernel/include/linux/spi/ads7846.h b/kernel/include/linux/spi/ads7846.h new file mode 100644 index 000000000..2f694f384 --- /dev/null +++ b/kernel/include/linux/spi/ads7846.h @@ -0,0 +1,61 @@ +/* linux/spi/ads7846.h */ + +/* Touchscreen characteristics vary between boards and models. The + * platform_data for the device's "struct device" holds this information. + * + * It's OK if the min/max values are zero. + */ +enum ads7846_filter { + ADS7846_FILTER_OK, + ADS7846_FILTER_REPEAT, + ADS7846_FILTER_IGNORE, +}; + +struct ads7846_platform_data { + u16 model; /* 7843, 7845, 7846, 7873. */ + u16 vref_delay_usecs; /* 0 for external vref; etc */ + u16 vref_mv; /* external vref value, milliVolts + * ads7846: if 0, use internal vref */ + bool keep_vref_on; /* set to keep vref on for differential + * measurements as well */ + bool swap_xy; /* swap x and y axes */ + + /* Settling time of the analog signals; a function of Vcc and the + * capacitance on the X/Y drivers. If set to non-zero, two samples + * are taken with settle_delay us apart, and the second one is used. + * ~150 uSec with 0.01uF caps. + */ + u16 settle_delay_usecs; + + /* If set to non-zero, after samples are taken this delay is applied + * and penirq is rechecked, to help avoid false events. This value + * is affected by the material used to build the touch layer. + */ + u16 penirq_recheck_delay_usecs; + + u16 x_plate_ohms; + u16 y_plate_ohms; + + u16 x_min, x_max; + u16 y_min, y_max; + u16 pressure_min, pressure_max; + + u16 debounce_max; /* max number of additional readings + * per sample */ + u16 debounce_tol; /* tolerance used for filtering */ + u16 debounce_rep; /* additional consecutive good readings + * required after the first two */ + int gpio_pendown; /* the GPIO used to decide the pendown + * state if get_pendown_state == NULL */ + int gpio_pendown_debounce; /* platform specific debounce time for + * the gpio_pendown */ + int (*get_pendown_state)(void); + int (*filter_init) (const struct ads7846_platform_data *pdata, + void **filter_data); + int (*filter) (void *filter_data, int data_idx, int *val); + void (*filter_cleanup)(void *filter_data); + void (*wait_for_sync)(void); + bool wakeup; + unsigned long irq_flags; +}; + diff --git a/kernel/include/linux/spi/at73c213.h b/kernel/include/linux/spi/at73c213.h new file mode 100644 index 000000000..0f20a70e5 --- /dev/null +++ b/kernel/include/linux/spi/at73c213.h @@ -0,0 +1,25 @@ +/* + * Board-specific data used to set up AT73c213 audio DAC driver. + */ + +#ifndef __LINUX_SPI_AT73C213_H +#define __LINUX_SPI_AT73C213_H + +/** + * at73c213_board_info - how the external DAC is wired to the device. + * + * @ssc_id: SSC platform_driver id the DAC shall use to stream the audio. + * @dac_clk: the external clock used to provide master clock to the DAC. + * @shortname: a short discription for the DAC, seen by userspace tools. + * + * This struct contains the configuration of the hardware connection to the + * external DAC. The DAC needs a master clock and a I2S audio stream. It also + * provides a name which is used to identify it in userspace tools. + */ +struct at73c213_board_info { + int ssc_id; + struct clk *dac_clk; + char shortname[32]; +}; + +#endif /* __LINUX_SPI_AT73C213_H */ diff --git a/kernel/include/linux/spi/at86rf230.h b/kernel/include/linux/spi/at86rf230.h new file mode 100644 index 000000000..b63fe6f5f --- /dev/null +++ b/kernel/include/linux/spi/at86rf230.h @@ -0,0 +1,28 @@ +/* + * AT86RF230/RF231 driver + * + * Copyright (C) 2009-2012 Siemens AG + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 + * as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Written by: + * Dmitry Eremin-Solenikov <dmitry.baryshkov@siemens.com> + */ +#ifndef AT86RF230_H +#define AT86RF230_H + +struct at86rf230_platform_data { + int rstn; + int slp_tr; + int dig2; + u8 xtal_trim; +}; + +#endif diff --git a/kernel/include/linux/spi/cc2520.h b/kernel/include/linux/spi/cc2520.h new file mode 100644 index 000000000..e741e8baa --- /dev/null +++ b/kernel/include/linux/spi/cc2520.h @@ -0,0 +1,27 @@ +/* Header file for cc2520 radio driver + * + * Copyright (C) 2014 Varka Bhadram <varkab@cdac.in> + * Md.Jamal Mohiuddin <mjmohiuddin@cdac.in> + * P Sowjanya <sowjanyap@cdac.in> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#ifndef __CC2520_H +#define __CC2520_H + +struct cc2520_platform_data { + int fifo; + int fifop; + int cca; + int sfd; + int reset; + int vreg; + bool amplified; +}; + +#endif diff --git a/kernel/include/linux/spi/corgi_lcd.h b/kernel/include/linux/spi/corgi_lcd.h new file mode 100644 index 000000000..6692b3418 --- /dev/null +++ b/kernel/include/linux/spi/corgi_lcd.h @@ -0,0 +1,20 @@ +#ifndef __LINUX_SPI_CORGI_LCD_H +#define __LINUX_SPI_CORGI_LCD_H + +#define CORGI_LCD_MODE_QVGA 1 +#define CORGI_LCD_MODE_VGA 2 + +struct corgi_lcd_platform_data { + int init_mode; + int max_intensity; + int default_intensity; + int limit_mask; + + int gpio_backlight_on; /* -1 if n/a */ + int gpio_backlight_cont; /* -1 if n/a */ + + void (*notify)(int intensity); + void (*kick_battery)(void); +}; + +#endif /* __LINUX_SPI_CORGI_LCD_H */ diff --git a/kernel/include/linux/spi/ds1305.h b/kernel/include/linux/spi/ds1305.h new file mode 100644 index 000000000..287ec830e --- /dev/null +++ b/kernel/include/linux/spi/ds1305.h @@ -0,0 +1,35 @@ +#ifndef __LINUX_SPI_DS1305_H +#define __LINUX_SPI_DS1305_H + +/* + * One-time configuration for ds1305 and ds1306 RTC chips. + * + * Put a pointer to this in spi_board_info.platform_data if you want to + * be sure that Linux (re)initializes this as needed ... after losing + * backup power, and potentially on the first boot. + */ +struct ds1305_platform_data { + + /* Trickle charge configuration: it's OK to leave out the MAGIC + * bitmask; mask in either DS1 or DS2, and then one of 2K/4k/8K. + */ +#define DS1305_TRICKLE_MAGIC 0xa0 +#define DS1305_TRICKLE_DS2 0x08 /* two diodes */ +#define DS1305_TRICKLE_DS1 0x04 /* one diode */ +#define DS1305_TRICKLE_2K 0x01 /* 2 KOhm resistance */ +#define DS1305_TRICKLE_4K 0x02 /* 4 KOhm resistance */ +#define DS1305_TRICKLE_8K 0x03 /* 8 KOhm resistance */ + u8 trickle; + + /* set only on ds1306 parts */ + bool is_ds1306; + + /* ds1306 only: enable 1 Hz output */ + bool en_1hz; + + /* REVISIT: the driver currently expects nINT0 to be wired + * as the alarm IRQ. ALM1 may also need to be set up ... + */ +}; + +#endif /* __LINUX_SPI_DS1305_H */ diff --git a/kernel/include/linux/spi/eeprom.h b/kernel/include/linux/spi/eeprom.h new file mode 100644 index 000000000..403e007ae --- /dev/null +++ b/kernel/include/linux/spi/eeprom.h @@ -0,0 +1,38 @@ +#ifndef __LINUX_SPI_EEPROM_H +#define __LINUX_SPI_EEPROM_H + +#include <linux/memory.h> + +/* + * Put one of these structures in platform_data for SPI EEPROMS handled + * by the "at25" driver. On SPI, most EEPROMS understand the same core + * command set. If you need to support EEPROMs that don't yet fit, add + * flags to support those protocol options. These values all come from + * the chip datasheets. + */ +struct spi_eeprom { + u32 byte_len; + char name[10]; + u16 page_size; /* for writes */ + u16 flags; +#define EE_ADDR1 0x0001 /* 8 bit addrs */ +#define EE_ADDR2 0x0002 /* 16 bit addrs */ +#define EE_ADDR3 0x0004 /* 24 bit addrs */ +#define EE_READONLY 0x0008 /* disallow writes */ + + /* + * Certain EEPROMS have a size that is larger than the number of address + * bytes would allow (e.g. like M95040 from ST that has 512 Byte size + * but uses only one address byte (A0 to A7) for addressing.) For + * the extra address bit (A8, A16 or A24) bit 3 of the instruction byte + * is used. This instruction bit is normally defined as don't care for + * other AT25 like chips. + */ +#define EE_INSTR_BIT3_IS_ADDR 0x0010 + + /* for exporting this chip's data to other kernel code */ + void (*setup)(struct memory_accessor *mem, void *context); + void *context; +}; + +#endif /* __LINUX_SPI_EEPROM_H */ diff --git a/kernel/include/linux/spi/flash.h b/kernel/include/linux/spi/flash.h new file mode 100644 index 000000000..3f22932e6 --- /dev/null +++ b/kernel/include/linux/spi/flash.h @@ -0,0 +1,31 @@ +#ifndef LINUX_SPI_FLASH_H +#define LINUX_SPI_FLASH_H + +struct mtd_partition; + +/** + * struct flash_platform_data: board-specific flash data + * @name: optional flash device name (eg, as used with mtdparts=) + * @parts: optional array of mtd_partitions for static partitioning + * @nr_parts: number of mtd_partitions for static partitoning + * @type: optional flash device type (e.g. m25p80 vs m25p64), for use + * with chips that can't be queried for JEDEC or other IDs + * + * Board init code (in arch/.../mach-xxx/board-yyy.c files) can + * provide information about SPI flash parts (such as DataFlash) to + * help set up the device and its appropriate default partitioning. + * + * Note that for DataFlash, sizes for pages, blocks, and sectors are + * rarely powers of two; and partitions should be sector-aligned. + */ +struct flash_platform_data { + char *name; + struct mtd_partition *parts; + unsigned int nr_parts; + + char *type; + + /* we'll likely add more ... use JEDEC IDs, etc */ +}; + +#endif diff --git a/kernel/include/linux/spi/ifx_modem.h b/kernel/include/linux/spi/ifx_modem.h new file mode 100644 index 000000000..394fec9e7 --- /dev/null +++ b/kernel/include/linux/spi/ifx_modem.h @@ -0,0 +1,19 @@ +#ifndef LINUX_IFX_MODEM_H +#define LINUX_IFX_MODEM_H + +struct ifx_modem_platform_data { + unsigned short rst_out; /* modem reset out */ + unsigned short pwr_on; /* power on */ + unsigned short rst_pmu; /* reset modem */ + unsigned short tx_pwr; /* modem power threshold */ + unsigned short srdy; /* SRDY */ + unsigned short mrdy; /* MRDY */ + unsigned char modem_type; /* Modem type */ + unsigned long max_hz; /* max SPI frequency */ + unsigned short use_dma:1; /* spi protocol driver supplies + dma-able addrs */ +}; +#define IFX_MODEM_6160 1 +#define IFX_MODEM_6260 2 + +#endif diff --git a/kernel/include/linux/spi/l4f00242t03.h b/kernel/include/linux/spi/l4f00242t03.h new file mode 100644 index 000000000..e69e9b51b --- /dev/null +++ b/kernel/include/linux/spi/l4f00242t03.h @@ -0,0 +1,25 @@ +/* + * l4f00242t03.h -- Platform glue for Epson L4F00242T03 LCD + * + * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com> + * Based on Marek Vasut work in lms283gf05.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. +*/ + +#ifndef _INCLUDE_LINUX_SPI_L4F00242T03_H_ +#define _INCLUDE_LINUX_SPI_L4F00242T03_H_ + +struct l4f00242t03_pdata { + unsigned int reset_gpio; + unsigned int data_enable_gpio; +}; + +#endif /* _INCLUDE_LINUX_SPI_L4F00242T03_H_ */ diff --git a/kernel/include/linux/spi/libertas_spi.h b/kernel/include/linux/spi/libertas_spi.h new file mode 100644 index 000000000..1b5d5384f --- /dev/null +++ b/kernel/include/linux/spi/libertas_spi.h @@ -0,0 +1,29 @@ +/* + * board-specific data for the libertas_spi driver. + * + * Copyright 2008 Analog Devices Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or (at + * your option) any later version. + */ +#ifndef _LIBERTAS_SPI_H_ +#define _LIBERTAS_SPI_H_ + +struct spi_device; + +struct libertas_spi_platform_data { + /* There are two ways to read data from the WLAN module's SPI + * interface. Setting 0 or 1 here controls which one is used. + * + * Usually you want to set use_dummy_writes = 1. + * However, if that doesn't work or if you are using a slow SPI clock + * speed, you may want to use 0 here. */ + u16 use_dummy_writes; + + /* Board specific setup/teardown */ + int (*setup)(struct spi_device *spi); + int (*teardown)(struct spi_device *spi); +}; +#endif diff --git a/kernel/include/linux/spi/lms283gf05.h b/kernel/include/linux/spi/lms283gf05.h new file mode 100644 index 000000000..fdd1d1d51 --- /dev/null +++ b/kernel/include/linux/spi/lms283gf05.h @@ -0,0 +1,24 @@ +/* + * lms283gf05.h - Platform glue for Samsung LMS283GF05 LCD + * + * Copyright (C) 2009 Marek Vasut <marek.vasut@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. +*/ + +#ifndef _INCLUDE_LINUX_SPI_LMS283GF05_H_ +#define _INCLUDE_LINUX_SPI_LMS283GF05_H_ + +struct lms283gf05_pdata { + unsigned long reset_gpio; + bool reset_inverted; +}; + +#endif /* _INCLUDE_LINUX_SPI_LMS283GF05_H_ */ diff --git a/kernel/include/linux/spi/max7301.h b/kernel/include/linux/spi/max7301.h new file mode 100644 index 000000000..bcaa2f762 --- /dev/null +++ b/kernel/include/linux/spi/max7301.h @@ -0,0 +1,35 @@ +#ifndef LINUX_SPI_MAX7301_H +#define LINUX_SPI_MAX7301_H + +#include <linux/gpio.h> + +/* + * Some registers must be read back to modify. + * To save time we cache them here in memory + */ +struct max7301 { + struct mutex lock; + u8 port_config[8]; /* field 0 is unused */ + u32 out_level; /* cached output levels */ + u32 input_pullup_active; + struct gpio_chip chip; + struct device *dev; + int (*write)(struct device *dev, unsigned int reg, unsigned int val); + int (*read)(struct device *dev, unsigned int reg); +}; + +struct max7301_platform_data { + /* number assigned to the first GPIO */ + unsigned base; + /* + * bitmask controlling the pullup configuration, + * + * _note_ the 4 lowest bits are unused, because the first 4 + * ports of the controller are not used, too. + */ + u32 input_pullup_active; +}; + +extern int __max730x_remove(struct device *dev); +extern int __max730x_probe(struct max7301 *ts); +#endif diff --git a/kernel/include/linux/spi/mc33880.h b/kernel/include/linux/spi/mc33880.h new file mode 100644 index 000000000..82ffccd6f --- /dev/null +++ b/kernel/include/linux/spi/mc33880.h @@ -0,0 +1,10 @@ +#ifndef LINUX_SPI_MC33880_H +#define LINUX_SPI_MC33880_H + +struct mc33880_platform_data { + /* number assigned to the first GPIO */ + unsigned base; +}; + +#endif + diff --git a/kernel/include/linux/spi/mcp23s08.h b/kernel/include/linux/spi/mcp23s08.h new file mode 100644 index 000000000..aa07d7b32 --- /dev/null +++ b/kernel/include/linux/spi/mcp23s08.h @@ -0,0 +1,43 @@ + +/* FIXME driver should be able to handle IRQs... */ + +struct mcp23s08_chip_info { + bool is_present; /* true if populated */ + unsigned pullups; /* BIT(x) means enable pullup x */ +}; + +struct mcp23s08_platform_data { + /* For mcp23s08, up to 4 slaves (numbered 0..3) can share one SPI + * chipselect, each providing 1 gpio_chip instance with 8 gpios. + * For mpc23s17, up to 8 slaves (numbered 0..7) can share one SPI + * chipselect, each providing 1 gpio_chip (port A + port B) with + * 16 gpios. + */ + struct mcp23s08_chip_info chip[8]; + + /* "base" is the number of the first GPIO. Dynamic assignment is + * not currently supported, and even if there are gaps in chip + * addressing the GPIO numbers are sequential .. so for example + * if only slaves 0 and 3 are present, their GPIOs range from + * base to base+15 (or base+31 for s17 variant). + */ + unsigned base; + /* Marks the device as a interrupt controller. + * NOTE: The interrupt functionality is only supported for i2c + * versions of the chips. The spi chips can also do the interrupts, + * but this is not supported by the linux driver yet. + */ + bool irq_controller; + + /* Sets the mirror flag in the IOCON register. Devices + * with two interrupt outputs (these are the devices ending with 17 and + * those that have 16 IOs) have two IO banks: IO 0-7 form bank 1 and + * IO 8-15 are bank 2. These chips have two different interrupt outputs: + * One for bank 1 and another for bank 2. If irq-mirror is set, both + * interrupts are generated regardless of the bank that an input change + * occurred on. If it is not set, the interrupt are only generated for + * the bank they belong to. + * On devices with only one interrupt output this property is useless. + */ + bool mirror; +}; diff --git a/kernel/include/linux/spi/mmc_spi.h b/kernel/include/linux/spi/mmc_spi.h new file mode 100644 index 000000000..274bc0fa0 --- /dev/null +++ b/kernel/include/linux/spi/mmc_spi.h @@ -0,0 +1,64 @@ +#ifndef __LINUX_SPI_MMC_SPI_H +#define __LINUX_SPI_MMC_SPI_H + +#include <linux/spi/spi.h> +#include <linux/interrupt.h> + +struct device; +struct mmc_host; + +#define MMC_SPI_USE_CD_GPIO (1 << 0) +#define MMC_SPI_USE_RO_GPIO (1 << 1) +#define MMC_SPI_CD_GPIO_ACTIVE_LOW (1 << 2) +#define MMC_SPI_RO_GPIO_ACTIVE_LOW (1 << 3) + +/* Put this in platform_data of a device being used to manage an MMC/SD + * card slot. (Modeled after PXA mmc glue; see that for usage examples.) + * + * REVISIT This is not a spi-specific notion. Any card slot should be + * able to handle it. If the MMC core doesn't adopt this kind of notion, + * switch the "struct device *" parameters over to "struct spi_device *". + */ +struct mmc_spi_platform_data { + /* driver activation and (optional) card detect irq hookup */ + int (*init)(struct device *, + irqreturn_t (*)(int, void *), + void *); + void (*exit)(struct device *, void *); + + /* + * Card Detect and Read Only GPIOs. To enable debouncing on the card + * detect GPIO, set the cd_debounce to the debounce time in + * microseconds. + */ + unsigned int flags; + unsigned int cd_gpio; + unsigned int cd_debounce; + unsigned int ro_gpio; + + /* Capabilities to pass into mmc core (e.g. MMC_CAP_NEEDS_POLL). */ + unsigned long caps; + unsigned long caps2; + + /* how long to debounce card detect, in msecs */ + u16 detect_delay; + + /* power management */ + u16 powerup_msecs; /* delay of up to 250 msec */ + u32 ocr_mask; /* available voltages */ + void (*setpower)(struct device *, unsigned int maskval); +}; + +#ifdef CONFIG_OF +extern struct mmc_spi_platform_data *mmc_spi_get_pdata(struct spi_device *spi); +extern void mmc_spi_put_pdata(struct spi_device *spi); +#else +static inline struct mmc_spi_platform_data * +mmc_spi_get_pdata(struct spi_device *spi) +{ + return spi->dev.platform_data; +} +static inline void mmc_spi_put_pdata(struct spi_device *spi) {} +#endif /* CONFIG_OF */ + +#endif /* __LINUX_SPI_MMC_SPI_H */ diff --git a/kernel/include/linux/spi/mxs-spi.h b/kernel/include/linux/spi/mxs-spi.h new file mode 100644 index 000000000..381d368b9 --- /dev/null +++ b/kernel/include/linux/spi/mxs-spi.h @@ -0,0 +1,144 @@ +/* + * include/linux/spi/mxs-spi.h + * + * Freescale i.MX233/i.MX28 SPI controller register definition + * + * Copyright 2008 Embedded Alley Solutions, Inc. + * Copyright 2009-2011 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __LINUX_SPI_MXS_SPI_H__ +#define __LINUX_SPI_MXS_SPI_H__ + +#include <linux/dmaengine.h> + +#define ssp_is_old(host) ((host)->devid == IMX23_SSP) + +/* SSP registers */ +#define HW_SSP_CTRL0 0x000 +#define BM_SSP_CTRL0_RUN (1 << 29) +#define BM_SSP_CTRL0_SDIO_IRQ_CHECK (1 << 28) +#define BM_SSP_CTRL0_LOCK_CS (1 << 27) +#define BM_SSP_CTRL0_IGNORE_CRC (1 << 26) +#define BM_SSP_CTRL0_READ (1 << 25) +#define BM_SSP_CTRL0_DATA_XFER (1 << 24) +#define BP_SSP_CTRL0_BUS_WIDTH 22 +#define BM_SSP_CTRL0_BUS_WIDTH (0x3 << 22) +#define BM_SSP_CTRL0_WAIT_FOR_IRQ (1 << 21) +#define BM_SSP_CTRL0_WAIT_FOR_CMD (1 << 20) +#define BM_SSP_CTRL0_LONG_RESP (1 << 19) +#define BM_SSP_CTRL0_GET_RESP (1 << 17) +#define BM_SSP_CTRL0_ENABLE (1 << 16) +#define BP_SSP_CTRL0_XFER_COUNT 0 +#define BM_SSP_CTRL0_XFER_COUNT 0xffff +#define HW_SSP_CMD0 0x010 +#define BM_SSP_CMD0_DBL_DATA_RATE_EN (1 << 25) +#define BM_SSP_CMD0_SLOW_CLKING_EN (1 << 22) +#define BM_SSP_CMD0_CONT_CLKING_EN (1 << 21) +#define BM_SSP_CMD0_APPEND_8CYC (1 << 20) +#define BP_SSP_CMD0_BLOCK_SIZE 16 +#define BM_SSP_CMD0_BLOCK_SIZE (0xf << 16) +#define BP_SSP_CMD0_BLOCK_COUNT 8 +#define BM_SSP_CMD0_BLOCK_COUNT (0xff << 8) +#define BP_SSP_CMD0_CMD 0 +#define BM_SSP_CMD0_CMD 0xff +#define HW_SSP_CMD1 0x020 +#define HW_SSP_XFER_SIZE 0x030 +#define HW_SSP_BLOCK_SIZE 0x040 +#define BP_SSP_BLOCK_SIZE_BLOCK_COUNT 4 +#define BM_SSP_BLOCK_SIZE_BLOCK_COUNT (0xffffff << 4) +#define BP_SSP_BLOCK_SIZE_BLOCK_SIZE 0 +#define BM_SSP_BLOCK_SIZE_BLOCK_SIZE 0xf +#define HW_SSP_TIMING(h) (ssp_is_old(h) ? 0x050 : 0x070) +#define BP_SSP_TIMING_TIMEOUT 16 +#define BM_SSP_TIMING_TIMEOUT (0xffff << 16) +#define BP_SSP_TIMING_CLOCK_DIVIDE 8 +#define BM_SSP_TIMING_CLOCK_DIVIDE (0xff << 8) +#define BF_SSP_TIMING_CLOCK_DIVIDE(v) \ + (((v) << 8) & BM_SSP_TIMING_CLOCK_DIVIDE) +#define BP_SSP_TIMING_CLOCK_RATE 0 +#define BM_SSP_TIMING_CLOCK_RATE 0xff +#define BF_SSP_TIMING_CLOCK_RATE(v) \ + (((v) << 0) & BM_SSP_TIMING_CLOCK_RATE) +#define HW_SSP_CTRL1(h) (ssp_is_old(h) ? 0x060 : 0x080) +#define BM_SSP_CTRL1_SDIO_IRQ (1 << 31) +#define BM_SSP_CTRL1_SDIO_IRQ_EN (1 << 30) +#define BM_SSP_CTRL1_RESP_ERR_IRQ (1 << 29) +#define BM_SSP_CTRL1_RESP_ERR_IRQ_EN (1 << 28) +#define BM_SSP_CTRL1_RESP_TIMEOUT_IRQ (1 << 27) +#define BM_SSP_CTRL1_RESP_TIMEOUT_IRQ_EN (1 << 26) +#define BM_SSP_CTRL1_DATA_TIMEOUT_IRQ (1 << 25) +#define BM_SSP_CTRL1_DATA_TIMEOUT_IRQ_EN (1 << 24) +#define BM_SSP_CTRL1_DATA_CRC_IRQ (1 << 23) +#define BM_SSP_CTRL1_DATA_CRC_IRQ_EN (1 << 22) +#define BM_SSP_CTRL1_FIFO_UNDERRUN_IRQ (1 << 21) +#define BM_SSP_CTRL1_FIFO_UNDERRUN_IRQ_EN (1 << 20) +#define BM_SSP_CTRL1_RECV_TIMEOUT_IRQ (1 << 17) +#define BM_SSP_CTRL1_RECV_TIMEOUT_IRQ_EN (1 << 16) +#define BM_SSP_CTRL1_FIFO_OVERRUN_IRQ (1 << 15) +#define BM_SSP_CTRL1_FIFO_OVERRUN_IRQ_EN (1 << 14) +#define BM_SSP_CTRL1_DMA_ENABLE (1 << 13) +#define BM_SSP_CTRL1_PHASE (1 << 10) +#define BM_SSP_CTRL1_POLARITY (1 << 9) +#define BP_SSP_CTRL1_WORD_LENGTH 4 +#define BM_SSP_CTRL1_WORD_LENGTH (0xf << 4) +#define BF_SSP_CTRL1_WORD_LENGTH(v) \ + (((v) << 4) & BM_SSP_CTRL1_WORD_LENGTH) +#define BV_SSP_CTRL1_WORD_LENGTH__FOUR_BITS 0x3 +#define BV_SSP_CTRL1_WORD_LENGTH__EIGHT_BITS 0x7 +#define BV_SSP_CTRL1_WORD_LENGTH__SIXTEEN_BITS 0xF +#define BP_SSP_CTRL1_SSP_MODE 0 +#define BM_SSP_CTRL1_SSP_MODE 0xf +#define BF_SSP_CTRL1_SSP_MODE(v) \ + (((v) << 0) & BM_SSP_CTRL1_SSP_MODE) +#define BV_SSP_CTRL1_SSP_MODE__SPI 0x0 +#define BV_SSP_CTRL1_SSP_MODE__SSI 0x1 +#define BV_SSP_CTRL1_SSP_MODE__SD_MMC 0x3 +#define BV_SSP_CTRL1_SSP_MODE__MS 0x4 + +#define HW_SSP_DATA(h) (ssp_is_old(h) ? 0x070 : 0x090) + +#define HW_SSP_SDRESP0(h) (ssp_is_old(h) ? 0x080 : 0x0a0) +#define HW_SSP_SDRESP1(h) (ssp_is_old(h) ? 0x090 : 0x0b0) +#define HW_SSP_SDRESP2(h) (ssp_is_old(h) ? 0x0a0 : 0x0c0) +#define HW_SSP_SDRESP3(h) (ssp_is_old(h) ? 0x0b0 : 0x0d0) +#define HW_SSP_STATUS(h) (ssp_is_old(h) ? 0x0c0 : 0x100) +#define BM_SSP_STATUS_CARD_DETECT (1 << 28) +#define BM_SSP_STATUS_SDIO_IRQ (1 << 17) +#define BM_SSP_STATUS_FIFO_EMPTY (1 << 5) + +#define BF_SSP(value, field) (((value) << BP_SSP_##field) & BM_SSP_##field) + +#define SSP_PIO_NUM 3 + +enum mxs_ssp_id { + IMX23_SSP, + IMX28_SSP, +}; + +struct mxs_ssp { + struct device *dev; + void __iomem *base; + struct clk *clk; + unsigned int clk_rate; + enum mxs_ssp_id devid; + + struct dma_chan *dmach; + unsigned int dma_dir; + enum dma_transfer_direction slave_dirn; + u32 ssp_pio_words[SSP_PIO_NUM]; +}; + +void mxs_ssp_set_clk_rate(struct mxs_ssp *ssp, unsigned int rate); + +#endif /* __LINUX_SPI_MXS_SPI_H__ */ diff --git a/kernel/include/linux/spi/pxa2xx_spi.h b/kernel/include/linux/spi/pxa2xx_spi.h new file mode 100644 index 000000000..6d36dacec --- /dev/null +++ b/kernel/include/linux/spi/pxa2xx_spi.h @@ -0,0 +1,60 @@ +/* + * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#ifndef __linux_pxa2xx_spi_h +#define __linux_pxa2xx_spi_h + +#include <linux/pxa2xx_ssp.h> + +#define PXA2XX_CS_ASSERT (0x01) +#define PXA2XX_CS_DEASSERT (0x02) + +struct dma_chan; + +/* device.platform_data for SSP controller devices */ +struct pxa2xx_spi_master { + u32 clock_enable; + u16 num_chipselect; + u8 enable_dma; + + /* DMA engine specific config */ + bool (*dma_filter)(struct dma_chan *chan, void *param); + void *tx_param; + void *rx_param; + + /* For non-PXA arches */ + struct ssp_device ssp; +}; + +/* spi_board_info.controller_data for SPI slave devices, + * copied to spi_device.platform_data ... mostly for dma tuning + */ +struct pxa2xx_spi_chip { + u8 tx_threshold; + u8 tx_hi_threshold; + u8 rx_threshold; + u8 dma_burst_size; + u32 timeout; + u8 enable_loopback; + int gpio_cs; + void (*cs_control)(u32 command); +}; + +#if defined(CONFIG_ARCH_PXA) || defined(CONFIG_ARCH_MMP) + +#include <linux/clk.h> + +extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info); + +#endif +#endif diff --git a/kernel/include/linux/spi/rspi.h b/kernel/include/linux/spi/rspi.h new file mode 100644 index 000000000..a693188cc --- /dev/null +++ b/kernel/include/linux/spi/rspi.h @@ -0,0 +1,26 @@ +/* + * Renesas SPI driver + * + * Copyright (C) 2012 Renesas Solutions Corp. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __LINUX_SPI_RENESAS_SPI_H__ +#define __LINUX_SPI_RENESAS_SPI_H__ + +struct rspi_plat_data { + unsigned int dma_tx_id; + unsigned int dma_rx_id; + + u16 num_chipselect; +}; + +#endif diff --git a/kernel/include/linux/spi/s3c24xx.h b/kernel/include/linux/spi/s3c24xx.h new file mode 100644 index 000000000..ca271c06c --- /dev/null +++ b/kernel/include/linux/spi/s3c24xx.h @@ -0,0 +1,28 @@ +/* + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * S3C2410 - SPI Controller platform_device info + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __LINUX_SPI_S3C24XX_H +#define __LINUX_SPI_S3C24XX_H __FILE__ + +struct s3c2410_spi_info { + int pin_cs; /* simple gpio cs */ + unsigned int num_cs; /* total chipselects */ + int bus_num; /* bus number to use. */ + + unsigned int use_fiq:1; /* use fiq */ + + void (*gpio_setup)(struct s3c2410_spi_info *spi, int enable); + void (*set_cs)(struct s3c2410_spi_info *spi, int cs, int pol); +}; + +extern int s3c24xx_set_fiq(unsigned int irq, bool on); + +#endif /* __LINUX_SPI_S3C24XX_H */ diff --git a/kernel/include/linux/spi/sh_hspi.h b/kernel/include/linux/spi/sh_hspi.h new file mode 100644 index 000000000..aa0d440ab --- /dev/null +++ b/kernel/include/linux/spi/sh_hspi.h @@ -0,0 +1,19 @@ +/* + * Copyright (C) 2011 Kuninori Morimoto + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#ifndef SH_HSPI_H +#define SH_HSPI_H + +struct sh_hspi_info { +}; + +#endif diff --git a/kernel/include/linux/spi/sh_msiof.h b/kernel/include/linux/spi/sh_msiof.h new file mode 100644 index 000000000..b087a85f5 --- /dev/null +++ b/kernel/include/linux/spi/sh_msiof.h @@ -0,0 +1,14 @@ +#ifndef __SPI_SH_MSIOF_H__ +#define __SPI_SH_MSIOF_H__ + +struct sh_msiof_spi_info { + int tx_fifo_override; + int rx_fifo_override; + u16 num_chipselect; + unsigned int dma_tx_id; + unsigned int dma_rx_id; + u32 dtdl; + u32 syncdl; +}; + +#endif /* __SPI_SH_MSIOF_H__ */ diff --git a/kernel/include/linux/spi/spi.h b/kernel/include/linux/spi/spi.h new file mode 100644 index 000000000..d67307234 --- /dev/null +++ b/kernel/include/linux/spi/spi.h @@ -0,0 +1,1056 @@ +/* + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __LINUX_SPI_H +#define __LINUX_SPI_H + +#include <linux/device.h> +#include <linux/mod_devicetable.h> +#include <linux/slab.h> +#include <linux/kthread.h> +#include <linux/completion.h> +#include <linux/scatterlist.h> + +struct dma_chan; + +/* + * INTERFACES between SPI master-side drivers and SPI infrastructure. + * (There's no SPI slave support for Linux yet...) + */ +extern struct bus_type spi_bus_type; + +/** + * struct spi_device - Master side proxy for an SPI slave device + * @dev: Driver model representation of the device. + * @master: SPI controller used with the device. + * @max_speed_hz: Maximum clock rate to be used with this chip + * (on this board); may be changed by the device's driver. + * The spi_transfer.speed_hz can override this for each transfer. + * @chip_select: Chipselect, distinguishing chips handled by @master. + * @mode: The spi mode defines how data is clocked out and in. + * This may be changed by the device's driver. + * The "active low" default for chipselect mode can be overridden + * (by specifying SPI_CS_HIGH) as can the "MSB first" default for + * each word in a transfer (by specifying SPI_LSB_FIRST). + * @bits_per_word: Data transfers involve one or more words; word sizes + * like eight or 12 bits are common. In-memory wordsizes are + * powers of two bytes (e.g. 20 bit samples use 32 bits). + * This may be changed by the device's driver, or left at the + * default (0) indicating protocol words are eight bit bytes. + * The spi_transfer.bits_per_word can override this for each transfer. + * @irq: Negative, or the number passed to request_irq() to receive + * interrupts from this device. + * @controller_state: Controller's runtime state + * @controller_data: Board-specific definitions for controller, such as + * FIFO initialization parameters; from board_info.controller_data + * @modalias: Name of the driver to use with this device, or an alias + * for that name. This appears in the sysfs "modalias" attribute + * for driver coldplugging, and in uevents used for hotplugging + * @cs_gpio: gpio number of the chipselect line (optional, -ENOENT when + * when not using a GPIO line) + * + * A @spi_device is used to interchange data between an SPI slave + * (usually a discrete chip) and CPU memory. + * + * In @dev, the platform_data is used to hold information about this + * device that's meaningful to the device's protocol driver, but not + * to its controller. One example might be an identifier for a chip + * variant with slightly different functionality; another might be + * information about how this particular board wires the chip's pins. + */ +struct spi_device { + struct device dev; + struct spi_master *master; + u32 max_speed_hz; + u8 chip_select; + u8 bits_per_word; + u16 mode; +#define SPI_CPHA 0x01 /* clock phase */ +#define SPI_CPOL 0x02 /* clock polarity */ +#define SPI_MODE_0 (0|0) /* (original MicroWire) */ +#define SPI_MODE_1 (0|SPI_CPHA) +#define SPI_MODE_2 (SPI_CPOL|0) +#define SPI_MODE_3 (SPI_CPOL|SPI_CPHA) +#define SPI_CS_HIGH 0x04 /* chipselect active high? */ +#define SPI_LSB_FIRST 0x08 /* per-word bits-on-wire */ +#define SPI_3WIRE 0x10 /* SI/SO signals shared */ +#define SPI_LOOP 0x20 /* loopback mode */ +#define SPI_NO_CS 0x40 /* 1 dev/bus, no chipselect */ +#define SPI_READY 0x80 /* slave pulls low to pause */ +#define SPI_TX_DUAL 0x100 /* transmit with 2 wires */ +#define SPI_TX_QUAD 0x200 /* transmit with 4 wires */ +#define SPI_RX_DUAL 0x400 /* receive with 2 wires */ +#define SPI_RX_QUAD 0x800 /* receive with 4 wires */ + int irq; + void *controller_state; + void *controller_data; + char modalias[SPI_NAME_SIZE]; + int cs_gpio; /* chip select gpio */ + + /* + * likely need more hooks for more protocol options affecting how + * the controller talks to each chip, like: + * - memory packing (12 bit samples into low bits, others zeroed) + * - priority + * - drop chipselect after each word + * - chipselect delays + * - ... + */ +}; + +static inline struct spi_device *to_spi_device(struct device *dev) +{ + return dev ? container_of(dev, struct spi_device, dev) : NULL; +} + +/* most drivers won't need to care about device refcounting */ +static inline struct spi_device *spi_dev_get(struct spi_device *spi) +{ + return (spi && get_device(&spi->dev)) ? spi : NULL; +} + +static inline void spi_dev_put(struct spi_device *spi) +{ + if (spi) + put_device(&spi->dev); +} + +/* ctldata is for the bus_master driver's runtime state */ +static inline void *spi_get_ctldata(struct spi_device *spi) +{ + return spi->controller_state; +} + +static inline void spi_set_ctldata(struct spi_device *spi, void *state) +{ + spi->controller_state = state; +} + +/* device driver data */ + +static inline void spi_set_drvdata(struct spi_device *spi, void *data) +{ + dev_set_drvdata(&spi->dev, data); +} + +static inline void *spi_get_drvdata(struct spi_device *spi) +{ + return dev_get_drvdata(&spi->dev); +} + +struct spi_message; +struct spi_transfer; + +/** + * struct spi_driver - Host side "protocol" driver + * @id_table: List of SPI devices supported by this driver + * @probe: Binds this driver to the spi device. Drivers can verify + * that the device is actually present, and may need to configure + * characteristics (such as bits_per_word) which weren't needed for + * the initial configuration done during system setup. + * @remove: Unbinds this driver from the spi device + * @shutdown: Standard shutdown callback used during system state + * transitions such as powerdown/halt and kexec + * @driver: SPI device drivers should initialize the name and owner + * field of this structure. + * + * This represents the kind of device driver that uses SPI messages to + * interact with the hardware at the other end of a SPI link. It's called + * a "protocol" driver because it works through messages rather than talking + * directly to SPI hardware (which is what the underlying SPI controller + * driver does to pass those messages). These protocols are defined in the + * specification for the device(s) supported by the driver. + * + * As a rule, those device protocols represent the lowest level interface + * supported by a driver, and it will support upper level interfaces too. + * Examples of such upper levels include frameworks like MTD, networking, + * MMC, RTC, filesystem character device nodes, and hardware monitoring. + */ +struct spi_driver { + const struct spi_device_id *id_table; + int (*probe)(struct spi_device *spi); + int (*remove)(struct spi_device *spi); + void (*shutdown)(struct spi_device *spi); + struct device_driver driver; +}; + +static inline struct spi_driver *to_spi_driver(struct device_driver *drv) +{ + return drv ? container_of(drv, struct spi_driver, driver) : NULL; +} + +extern int spi_register_driver(struct spi_driver *sdrv); + +/** + * spi_unregister_driver - reverse effect of spi_register_driver + * @sdrv: the driver to unregister + * Context: can sleep + */ +static inline void spi_unregister_driver(struct spi_driver *sdrv) +{ + if (sdrv) + driver_unregister(&sdrv->driver); +} + +/** + * module_spi_driver() - Helper macro for registering a SPI driver + * @__spi_driver: spi_driver struct + * + * Helper macro for SPI drivers which do not do anything special in module + * init/exit. This eliminates a lot of boilerplate. Each module may only + * use this macro once, and calling it replaces module_init() and module_exit() + */ +#define module_spi_driver(__spi_driver) \ + module_driver(__spi_driver, spi_register_driver, \ + spi_unregister_driver) + +/** + * struct spi_master - interface to SPI master controller + * @dev: device interface to this driver + * @list: link with the global spi_master list + * @bus_num: board-specific (and often SOC-specific) identifier for a + * given SPI controller. + * @num_chipselect: chipselects are used to distinguish individual + * SPI slaves, and are numbered from zero to num_chipselects. + * each slave has a chipselect signal, but it's common that not + * every chipselect is connected to a slave. + * @dma_alignment: SPI controller constraint on DMA buffers alignment. + * @mode_bits: flags understood by this controller driver + * @bits_per_word_mask: A mask indicating which values of bits_per_word are + * supported by the driver. Bit n indicates that a bits_per_word n+1 is + * supported. If set, the SPI core will reject any transfer with an + * unsupported bits_per_word. If not set, this value is simply ignored, + * and it's up to the individual driver to perform any validation. + * @min_speed_hz: Lowest supported transfer speed + * @max_speed_hz: Highest supported transfer speed + * @flags: other constraints relevant to this driver + * @bus_lock_spinlock: spinlock for SPI bus locking + * @bus_lock_mutex: mutex for SPI bus locking + * @bus_lock_flag: indicates that the SPI bus is locked for exclusive use + * @setup: updates the device mode and clocking records used by a + * device's SPI controller; protocol code may call this. This + * must fail if an unrecognized or unsupported mode is requested. + * It's always safe to call this unless transfers are pending on + * the device whose settings are being modified. + * @transfer: adds a message to the controller's transfer queue. + * @cleanup: frees controller-specific state + * @can_dma: determine whether this master supports DMA + * @queued: whether this master is providing an internal message queue + * @kworker: thread struct for message pump + * @kworker_task: pointer to task for message pump kworker thread + * @pump_messages: work struct for scheduling work to the message pump + * @queue_lock: spinlock to syncronise access to message queue + * @queue: message queue + * @idling: the device is entering idle state + * @cur_msg: the currently in-flight message + * @cur_msg_prepared: spi_prepare_message was called for the currently + * in-flight message + * @cur_msg_mapped: message has been mapped for DMA + * @xfer_completion: used by core transfer_one_message() + * @busy: message pump is busy + * @running: message pump is running + * @rt: whether this queue is set to run as a realtime task + * @auto_runtime_pm: the core should ensure a runtime PM reference is held + * while the hardware is prepared, using the parent + * device for the spidev + * @max_dma_len: Maximum length of a DMA transfer for the device. + * @prepare_transfer_hardware: a message will soon arrive from the queue + * so the subsystem requests the driver to prepare the transfer hardware + * by issuing this call + * @transfer_one_message: the subsystem calls the driver to transfer a single + * message while queuing transfers that arrive in the meantime. When the + * driver is finished with this message, it must call + * spi_finalize_current_message() so the subsystem can issue the next + * message + * @unprepare_transfer_hardware: there are currently no more messages on the + * queue so the subsystem notifies the driver that it may relax the + * hardware by issuing this call + * @set_cs: set the logic level of the chip select line. May be called + * from interrupt context. + * @prepare_message: set up the controller to transfer a single message, + * for example doing DMA mapping. Called from threaded + * context. + * @transfer_one: transfer a single spi_transfer. + * - return 0 if the transfer is finished, + * - return 1 if the transfer is still in progress. When + * the driver is finished with this transfer it must + * call spi_finalize_current_transfer() so the subsystem + * can issue the next transfer. Note: transfer_one and + * transfer_one_message are mutually exclusive; when both + * are set, the generic subsystem does not call your + * transfer_one callback. + * @handle_err: the subsystem calls the driver to handle an error that occurs + * in the generic implementation of transfer_one_message(). + * @unprepare_message: undo any work done by prepare_message(). + * @cs_gpios: Array of GPIOs to use as chip select lines; one per CS + * number. Any individual value may be -ENOENT for CS lines that + * are not GPIOs (driven by the SPI controller itself). + * @dma_tx: DMA transmit channel + * @dma_rx: DMA receive channel + * @dummy_rx: dummy receive buffer for full-duplex devices + * @dummy_tx: dummy transmit buffer for full-duplex devices + * + * Each SPI master controller can communicate with one or more @spi_device + * children. These make a small bus, sharing MOSI, MISO and SCK signals + * but not chip select signals. Each device may be configured to use a + * different clock rate, since those shared signals are ignored unless + * the chip is selected. + * + * The driver for an SPI controller manages access to those devices through + * a queue of spi_message transactions, copying data between CPU memory and + * an SPI slave device. For each such message it queues, it calls the + * message's completion function when the transaction completes. + */ +struct spi_master { + struct device dev; + + struct list_head list; + + /* other than negative (== assign one dynamically), bus_num is fully + * board-specific. usually that simplifies to being SOC-specific. + * example: one SOC has three SPI controllers, numbered 0..2, + * and one board's schematics might show it using SPI-2. software + * would normally use bus_num=2 for that controller. + */ + s16 bus_num; + + /* chipselects will be integral to many controllers; some others + * might use board-specific GPIOs. + */ + u16 num_chipselect; + + /* some SPI controllers pose alignment requirements on DMAable + * buffers; let protocol drivers know about these requirements. + */ + u16 dma_alignment; + + /* spi_device.mode flags understood by this controller driver */ + u16 mode_bits; + + /* bitmask of supported bits_per_word for transfers */ + u32 bits_per_word_mask; +#define SPI_BPW_MASK(bits) BIT((bits) - 1) +#define SPI_BIT_MASK(bits) (((bits) == 32) ? ~0U : (BIT(bits) - 1)) +#define SPI_BPW_RANGE_MASK(min, max) (SPI_BIT_MASK(max) - SPI_BIT_MASK(min - 1)) + + /* limits on transfer speed */ + u32 min_speed_hz; + u32 max_speed_hz; + + /* other constraints relevant to this driver */ + u16 flags; +#define SPI_MASTER_HALF_DUPLEX BIT(0) /* can't do full duplex */ +#define SPI_MASTER_NO_RX BIT(1) /* can't do buffer read */ +#define SPI_MASTER_NO_TX BIT(2) /* can't do buffer write */ +#define SPI_MASTER_MUST_RX BIT(3) /* requires rx */ +#define SPI_MASTER_MUST_TX BIT(4) /* requires tx */ + + /* lock and mutex for SPI bus locking */ + spinlock_t bus_lock_spinlock; + struct mutex bus_lock_mutex; + + /* flag indicating that the SPI bus is locked for exclusive use */ + bool bus_lock_flag; + + /* Setup mode and clock, etc (spi driver may call many times). + * + * IMPORTANT: this may be called when transfers to another + * device are active. DO NOT UPDATE SHARED REGISTERS in ways + * which could break those transfers. + */ + int (*setup)(struct spi_device *spi); + + /* bidirectional bulk transfers + * + * + The transfer() method may not sleep; its main role is + * just to add the message to the queue. + * + For now there's no remove-from-queue operation, or + * any other request management + * + To a given spi_device, message queueing is pure fifo + * + * + The master's main job is to process its message queue, + * selecting a chip then transferring data + * + If there are multiple spi_device children, the i/o queue + * arbitration algorithm is unspecified (round robin, fifo, + * priority, reservations, preemption, etc) + * + * + Chipselect stays active during the entire message + * (unless modified by spi_transfer.cs_change != 0). + * + The message transfers use clock and SPI mode parameters + * previously established by setup() for this device + */ + int (*transfer)(struct spi_device *spi, + struct spi_message *mesg); + + /* called on release() to free memory provided by spi_master */ + void (*cleanup)(struct spi_device *spi); + + /* + * Used to enable core support for DMA handling, if can_dma() + * exists and returns true then the transfer will be mapped + * prior to transfer_one() being called. The driver should + * not modify or store xfer and dma_tx and dma_rx must be set + * while the device is prepared. + */ + bool (*can_dma)(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *xfer); + + /* + * These hooks are for drivers that want to use the generic + * master transfer queueing mechanism. If these are used, the + * transfer() function above must NOT be specified by the driver. + * Over time we expect SPI drivers to be phased over to this API. + */ + bool queued; + struct kthread_worker kworker; + struct task_struct *kworker_task; + struct kthread_work pump_messages; + spinlock_t queue_lock; + struct list_head queue; + struct spi_message *cur_msg; + bool idling; + bool busy; + bool running; + bool rt; + bool auto_runtime_pm; + bool cur_msg_prepared; + bool cur_msg_mapped; + struct completion xfer_completion; + size_t max_dma_len; + + int (*prepare_transfer_hardware)(struct spi_master *master); + int (*transfer_one_message)(struct spi_master *master, + struct spi_message *mesg); + int (*unprepare_transfer_hardware)(struct spi_master *master); + int (*prepare_message)(struct spi_master *master, + struct spi_message *message); + int (*unprepare_message)(struct spi_master *master, + struct spi_message *message); + + /* + * These hooks are for drivers that use a generic implementation + * of transfer_one_message() provied by the core. + */ + void (*set_cs)(struct spi_device *spi, bool enable); + int (*transfer_one)(struct spi_master *master, struct spi_device *spi, + struct spi_transfer *transfer); + void (*handle_err)(struct spi_master *master, + struct spi_message *message); + + /* gpio chip select */ + int *cs_gpios; + + /* DMA channels for use with core dmaengine helpers */ + struct dma_chan *dma_tx; + struct dma_chan *dma_rx; + + /* dummy data for full duplex devices */ + void *dummy_rx; + void *dummy_tx; +}; + +static inline void *spi_master_get_devdata(struct spi_master *master) +{ + return dev_get_drvdata(&master->dev); +} + +static inline void spi_master_set_devdata(struct spi_master *master, void *data) +{ + dev_set_drvdata(&master->dev, data); +} + +static inline struct spi_master *spi_master_get(struct spi_master *master) +{ + if (!master || !get_device(&master->dev)) + return NULL; + return master; +} + +static inline void spi_master_put(struct spi_master *master) +{ + if (master) + put_device(&master->dev); +} + +/* PM calls that need to be issued by the driver */ +extern int spi_master_suspend(struct spi_master *master); +extern int spi_master_resume(struct spi_master *master); + +/* Calls the driver make to interact with the message queue */ +extern struct spi_message *spi_get_next_queued_message(struct spi_master *master); +extern void spi_finalize_current_message(struct spi_master *master); +extern void spi_finalize_current_transfer(struct spi_master *master); + +/* the spi driver core manages memory for the spi_master classdev */ +extern struct spi_master * +spi_alloc_master(struct device *host, unsigned size); + +extern int spi_register_master(struct spi_master *master); +extern int devm_spi_register_master(struct device *dev, + struct spi_master *master); +extern void spi_unregister_master(struct spi_master *master); + +extern struct spi_master *spi_busnum_to_master(u16 busnum); + +/*---------------------------------------------------------------------------*/ + +/* + * I/O INTERFACE between SPI controller and protocol drivers + * + * Protocol drivers use a queue of spi_messages, each transferring data + * between the controller and memory buffers. + * + * The spi_messages themselves consist of a series of read+write transfer + * segments. Those segments always read the same number of bits as they + * write; but one or the other is easily ignored by passing a null buffer + * pointer. (This is unlike most types of I/O API, because SPI hardware + * is full duplex.) + * + * NOTE: Allocation of spi_transfer and spi_message memory is entirely + * up to the protocol driver, which guarantees the integrity of both (as + * well as the data buffers) for as long as the message is queued. + */ + +/** + * struct spi_transfer - a read/write buffer pair + * @tx_buf: data to be written (dma-safe memory), or NULL + * @rx_buf: data to be read (dma-safe memory), or NULL + * @tx_dma: DMA address of tx_buf, if @spi_message.is_dma_mapped + * @rx_dma: DMA address of rx_buf, if @spi_message.is_dma_mapped + * @tx_nbits: number of bits used for writing. If 0 the default + * (SPI_NBITS_SINGLE) is used. + * @rx_nbits: number of bits used for reading. If 0 the default + * (SPI_NBITS_SINGLE) is used. + * @len: size of rx and tx buffers (in bytes) + * @speed_hz: Select a speed other than the device default for this + * transfer. If 0 the default (from @spi_device) is used. + * @bits_per_word: select a bits_per_word other than the device default + * for this transfer. If 0 the default (from @spi_device) is used. + * @cs_change: affects chipselect after this transfer completes + * @delay_usecs: microseconds to delay after this transfer before + * (optionally) changing the chipselect status, then starting + * the next transfer or completing this @spi_message. + * @transfer_list: transfers are sequenced through @spi_message.transfers + * @tx_sg: Scatterlist for transmit, currently not for client use + * @rx_sg: Scatterlist for receive, currently not for client use + * + * SPI transfers always write the same number of bytes as they read. + * Protocol drivers should always provide @rx_buf and/or @tx_buf. + * In some cases, they may also want to provide DMA addresses for + * the data being transferred; that may reduce overhead, when the + * underlying driver uses dma. + * + * If the transmit buffer is null, zeroes will be shifted out + * while filling @rx_buf. If the receive buffer is null, the data + * shifted in will be discarded. Only "len" bytes shift out (or in). + * It's an error to try to shift out a partial word. (For example, by + * shifting out three bytes with word size of sixteen or twenty bits; + * the former uses two bytes per word, the latter uses four bytes.) + * + * In-memory data values are always in native CPU byte order, translated + * from the wire byte order (big-endian except with SPI_LSB_FIRST). So + * for example when bits_per_word is sixteen, buffers are 2N bytes long + * (@len = 2N) and hold N sixteen bit words in CPU byte order. + * + * When the word size of the SPI transfer is not a power-of-two multiple + * of eight bits, those in-memory words include extra bits. In-memory + * words are always seen by protocol drivers as right-justified, so the + * undefined (rx) or unused (tx) bits are always the most significant bits. + * + * All SPI transfers start with the relevant chipselect active. Normally + * it stays selected until after the last transfer in a message. Drivers + * can affect the chipselect signal using cs_change. + * + * (i) If the transfer isn't the last one in the message, this flag is + * used to make the chipselect briefly go inactive in the middle of the + * message. Toggling chipselect in this way may be needed to terminate + * a chip command, letting a single spi_message perform all of group of + * chip transactions together. + * + * (ii) When the transfer is the last one in the message, the chip may + * stay selected until the next transfer. On multi-device SPI busses + * with nothing blocking messages going to other devices, this is just + * a performance hint; starting a message to another device deselects + * this one. But in other cases, this can be used to ensure correctness. + * Some devices need protocol transactions to be built from a series of + * spi_message submissions, where the content of one message is determined + * by the results of previous messages and where the whole transaction + * ends when the chipselect goes intactive. + * + * When SPI can transfer in 1x,2x or 4x. It can get this transfer information + * from device through @tx_nbits and @rx_nbits. In Bi-direction, these + * two should both be set. User can set transfer mode with SPI_NBITS_SINGLE(1x) + * SPI_NBITS_DUAL(2x) and SPI_NBITS_QUAD(4x) to support these three transfer. + * + * The code that submits an spi_message (and its spi_transfers) + * to the lower layers is responsible for managing its memory. + * Zero-initialize every field you don't set up explicitly, to + * insulate against future API updates. After you submit a message + * and its transfers, ignore them until its completion callback. + */ +struct spi_transfer { + /* it's ok if tx_buf == rx_buf (right?) + * for MicroWire, one buffer must be null + * buffers must work with dma_*map_single() calls, unless + * spi_message.is_dma_mapped reports a pre-existing mapping + */ + const void *tx_buf; + void *rx_buf; + unsigned len; + + dma_addr_t tx_dma; + dma_addr_t rx_dma; + struct sg_table tx_sg; + struct sg_table rx_sg; + + unsigned cs_change:1; + unsigned tx_nbits:3; + unsigned rx_nbits:3; +#define SPI_NBITS_SINGLE 0x01 /* 1bit transfer */ +#define SPI_NBITS_DUAL 0x02 /* 2bits transfer */ +#define SPI_NBITS_QUAD 0x04 /* 4bits transfer */ + u8 bits_per_word; + u16 delay_usecs; + u32 speed_hz; + + struct list_head transfer_list; +}; + +/** + * struct spi_message - one multi-segment SPI transaction + * @transfers: list of transfer segments in this transaction + * @spi: SPI device to which the transaction is queued + * @is_dma_mapped: if true, the caller provided both dma and cpu virtual + * addresses for each transfer buffer + * @complete: called to report transaction completions + * @context: the argument to complete() when it's called + * @frame_length: the total number of bytes in the message + * @actual_length: the total number of bytes that were transferred in all + * successful segments + * @status: zero for success, else negative errno + * @queue: for use by whichever driver currently owns the message + * @state: for use by whichever driver currently owns the message + * + * A @spi_message is used to execute an atomic sequence of data transfers, + * each represented by a struct spi_transfer. The sequence is "atomic" + * in the sense that no other spi_message may use that SPI bus until that + * sequence completes. On some systems, many such sequences can execute as + * as single programmed DMA transfer. On all systems, these messages are + * queued, and might complete after transactions to other devices. Messages + * sent to a given spi_device are always executed in FIFO order. + * + * The code that submits an spi_message (and its spi_transfers) + * to the lower layers is responsible for managing its memory. + * Zero-initialize every field you don't set up explicitly, to + * insulate against future API updates. After you submit a message + * and its transfers, ignore them until its completion callback. + */ +struct spi_message { + struct list_head transfers; + + struct spi_device *spi; + + unsigned is_dma_mapped:1; + + /* REVISIT: we might want a flag affecting the behavior of the + * last transfer ... allowing things like "read 16 bit length L" + * immediately followed by "read L bytes". Basically imposing + * a specific message scheduling algorithm. + * + * Some controller drivers (message-at-a-time queue processing) + * could provide that as their default scheduling algorithm. But + * others (with multi-message pipelines) could need a flag to + * tell them about such special cases. + */ + + /* completion is reported through a callback */ + void (*complete)(void *context); + void *context; + unsigned frame_length; + unsigned actual_length; + int status; + + /* for optional use by whatever driver currently owns the + * spi_message ... between calls to spi_async and then later + * complete(), that's the spi_master controller driver. + */ + struct list_head queue; + void *state; +}; + +static inline void spi_message_init(struct spi_message *m) +{ + memset(m, 0, sizeof *m); + INIT_LIST_HEAD(&m->transfers); +} + +static inline void +spi_message_add_tail(struct spi_transfer *t, struct spi_message *m) +{ + list_add_tail(&t->transfer_list, &m->transfers); +} + +static inline void +spi_transfer_del(struct spi_transfer *t) +{ + list_del(&t->transfer_list); +} + +/** + * spi_message_init_with_transfers - Initialize spi_message and append transfers + * @m: spi_message to be initialized + * @xfers: An array of spi transfers + * @num_xfers: Number of items in the xfer array + * + * This function initializes the given spi_message and adds each spi_transfer in + * the given array to the message. + */ +static inline void +spi_message_init_with_transfers(struct spi_message *m, +struct spi_transfer *xfers, unsigned int num_xfers) +{ + unsigned int i; + + spi_message_init(m); + for (i = 0; i < num_xfers; ++i) + spi_message_add_tail(&xfers[i], m); +} + +/* It's fine to embed message and transaction structures in other data + * structures so long as you don't free them while they're in use. + */ + +static inline struct spi_message *spi_message_alloc(unsigned ntrans, gfp_t flags) +{ + struct spi_message *m; + + m = kzalloc(sizeof(struct spi_message) + + ntrans * sizeof(struct spi_transfer), + flags); + if (m) { + unsigned i; + struct spi_transfer *t = (struct spi_transfer *)(m + 1); + + INIT_LIST_HEAD(&m->transfers); + for (i = 0; i < ntrans; i++, t++) + spi_message_add_tail(t, m); + } + return m; +} + +static inline void spi_message_free(struct spi_message *m) +{ + kfree(m); +} + +extern int spi_setup(struct spi_device *spi); +extern int spi_async(struct spi_device *spi, struct spi_message *message); +extern int spi_async_locked(struct spi_device *spi, + struct spi_message *message); + +/*---------------------------------------------------------------------------*/ + +/* All these synchronous SPI transfer routines are utilities layered + * over the core async transfer primitive. Here, "synchronous" means + * they will sleep uninterruptibly until the async transfer completes. + */ + +extern int spi_sync(struct spi_device *spi, struct spi_message *message); +extern int spi_sync_locked(struct spi_device *spi, struct spi_message *message); +extern int spi_bus_lock(struct spi_master *master); +extern int spi_bus_unlock(struct spi_master *master); + +/** + * spi_write - SPI synchronous write + * @spi: device to which data will be written + * @buf: data buffer + * @len: data buffer size + * Context: can sleep + * + * This writes the buffer and returns zero or a negative error code. + * Callable only from contexts that can sleep. + */ +static inline int +spi_write(struct spi_device *spi, const void *buf, size_t len) +{ + struct spi_transfer t = { + .tx_buf = buf, + .len = len, + }; + struct spi_message m; + + spi_message_init(&m); + spi_message_add_tail(&t, &m); + return spi_sync(spi, &m); +} + +/** + * spi_read - SPI synchronous read + * @spi: device from which data will be read + * @buf: data buffer + * @len: data buffer size + * Context: can sleep + * + * This reads the buffer and returns zero or a negative error code. + * Callable only from contexts that can sleep. + */ +static inline int +spi_read(struct spi_device *spi, void *buf, size_t len) +{ + struct spi_transfer t = { + .rx_buf = buf, + .len = len, + }; + struct spi_message m; + + spi_message_init(&m); + spi_message_add_tail(&t, &m); + return spi_sync(spi, &m); +} + +/** + * spi_sync_transfer - synchronous SPI data transfer + * @spi: device with which data will be exchanged + * @xfers: An array of spi_transfers + * @num_xfers: Number of items in the xfer array + * Context: can sleep + * + * Does a synchronous SPI data transfer of the given spi_transfer array. + * + * For more specific semantics see spi_sync(). + * + * It returns zero on success, else a negative error code. + */ +static inline int +spi_sync_transfer(struct spi_device *spi, struct spi_transfer *xfers, + unsigned int num_xfers) +{ + struct spi_message msg; + + spi_message_init_with_transfers(&msg, xfers, num_xfers); + + return spi_sync(spi, &msg); +} + +/* this copies txbuf and rxbuf data; for small transfers only! */ +extern int spi_write_then_read(struct spi_device *spi, + const void *txbuf, unsigned n_tx, + void *rxbuf, unsigned n_rx); + +/** + * spi_w8r8 - SPI synchronous 8 bit write followed by 8 bit read + * @spi: device with which data will be exchanged + * @cmd: command to be written before data is read back + * Context: can sleep + * + * This returns the (unsigned) eight bit number returned by the + * device, or else a negative error code. Callable only from + * contexts that can sleep. + */ +static inline ssize_t spi_w8r8(struct spi_device *spi, u8 cmd) +{ + ssize_t status; + u8 result; + + status = spi_write_then_read(spi, &cmd, 1, &result, 1); + + /* return negative errno or unsigned value */ + return (status < 0) ? status : result; +} + +/** + * spi_w8r16 - SPI synchronous 8 bit write followed by 16 bit read + * @spi: device with which data will be exchanged + * @cmd: command to be written before data is read back + * Context: can sleep + * + * This returns the (unsigned) sixteen bit number returned by the + * device, or else a negative error code. Callable only from + * contexts that can sleep. + * + * The number is returned in wire-order, which is at least sometimes + * big-endian. + */ +static inline ssize_t spi_w8r16(struct spi_device *spi, u8 cmd) +{ + ssize_t status; + u16 result; + + status = spi_write_then_read(spi, &cmd, 1, &result, 2); + + /* return negative errno or unsigned value */ + return (status < 0) ? status : result; +} + +/** + * spi_w8r16be - SPI synchronous 8 bit write followed by 16 bit big-endian read + * @spi: device with which data will be exchanged + * @cmd: command to be written before data is read back + * Context: can sleep + * + * This returns the (unsigned) sixteen bit number returned by the device in cpu + * endianness, or else a negative error code. Callable only from contexts that + * can sleep. + * + * This function is similar to spi_w8r16, with the exception that it will + * convert the read 16 bit data word from big-endian to native endianness. + * + */ +static inline ssize_t spi_w8r16be(struct spi_device *spi, u8 cmd) + +{ + ssize_t status; + __be16 result; + + status = spi_write_then_read(spi, &cmd, 1, &result, 2); + if (status < 0) + return status; + + return be16_to_cpu(result); +} + +/*---------------------------------------------------------------------------*/ + +/* + * INTERFACE between board init code and SPI infrastructure. + * + * No SPI driver ever sees these SPI device table segments, but + * it's how the SPI core (or adapters that get hotplugged) grows + * the driver model tree. + * + * As a rule, SPI devices can't be probed. Instead, board init code + * provides a table listing the devices which are present, with enough + * information to bind and set up the device's driver. There's basic + * support for nonstatic configurations too; enough to handle adding + * parport adapters, or microcontrollers acting as USB-to-SPI bridges. + */ + +/** + * struct spi_board_info - board-specific template for a SPI device + * @modalias: Initializes spi_device.modalias; identifies the driver. + * @platform_data: Initializes spi_device.platform_data; the particular + * data stored there is driver-specific. + * @controller_data: Initializes spi_device.controller_data; some + * controllers need hints about hardware setup, e.g. for DMA. + * @irq: Initializes spi_device.irq; depends on how the board is wired. + * @max_speed_hz: Initializes spi_device.max_speed_hz; based on limits + * from the chip datasheet and board-specific signal quality issues. + * @bus_num: Identifies which spi_master parents the spi_device; unused + * by spi_new_device(), and otherwise depends on board wiring. + * @chip_select: Initializes spi_device.chip_select; depends on how + * the board is wired. + * @mode: Initializes spi_device.mode; based on the chip datasheet, board + * wiring (some devices support both 3WIRE and standard modes), and + * possibly presence of an inverter in the chipselect path. + * + * When adding new SPI devices to the device tree, these structures serve + * as a partial device template. They hold information which can't always + * be determined by drivers. Information that probe() can establish (such + * as the default transfer wordsize) is not included here. + * + * These structures are used in two places. Their primary role is to + * be stored in tables of board-specific device descriptors, which are + * declared early in board initialization and then used (much later) to + * populate a controller's device tree after the that controller's driver + * initializes. A secondary (and atypical) role is as a parameter to + * spi_new_device() call, which happens after those controller drivers + * are active in some dynamic board configuration models. + */ +struct spi_board_info { + /* the device name and module name are coupled, like platform_bus; + * "modalias" is normally the driver name. + * + * platform_data goes to spi_device.dev.platform_data, + * controller_data goes to spi_device.controller_data, + * irq is copied too + */ + char modalias[SPI_NAME_SIZE]; + const void *platform_data; + void *controller_data; + int irq; + + /* slower signaling on noisy or low voltage boards */ + u32 max_speed_hz; + + + /* bus_num is board specific and matches the bus_num of some + * spi_master that will probably be registered later. + * + * chip_select reflects how this chip is wired to that master; + * it's less than num_chipselect. + */ + u16 bus_num; + u16 chip_select; + + /* mode becomes spi_device.mode, and is essential for chips + * where the default of SPI_CS_HIGH = 0 is wrong. + */ + u16 mode; + + /* ... may need additional spi_device chip config data here. + * avoid stuff protocol drivers can set; but include stuff + * needed to behave without being bound to a driver: + * - quirks like clock rate mattering when not selected + */ +}; + +#ifdef CONFIG_SPI +extern int +spi_register_board_info(struct spi_board_info const *info, unsigned n); +#else +/* board init code may ignore whether SPI is configured or not */ +static inline int +spi_register_board_info(struct spi_board_info const *info, unsigned n) + { return 0; } +#endif + + +/* If you're hotplugging an adapter with devices (parport, usb, etc) + * use spi_new_device() to describe each device. You can also call + * spi_unregister_device() to start making that device vanish, but + * normally that would be handled by spi_unregister_master(). + * + * You can also use spi_alloc_device() and spi_add_device() to use a two + * stage registration sequence for each spi_device. This gives the caller + * some more control over the spi_device structure before it is registered, + * but requires that caller to initialize fields that would otherwise + * be defined using the board info. + */ +extern struct spi_device * +spi_alloc_device(struct spi_master *master); + +extern int +spi_add_device(struct spi_device *spi); + +extern struct spi_device * +spi_new_device(struct spi_master *, struct spi_board_info *); + +static inline void +spi_unregister_device(struct spi_device *spi) +{ + if (spi) + device_unregister(&spi->dev); +} + +extern const struct spi_device_id * +spi_get_device_id(const struct spi_device *sdev); + +static inline bool +spi_transfer_is_last(struct spi_master *master, struct spi_transfer *xfer) +{ + return list_is_last(&xfer->transfer_list, &master->cur_msg->transfers); +} + +#endif /* __LINUX_SPI_H */ diff --git a/kernel/include/linux/spi/spi_bitbang.h b/kernel/include/linux/spi/spi_bitbang.h new file mode 100644 index 000000000..85578d4be --- /dev/null +++ b/kernel/include/linux/spi/spi_bitbang.h @@ -0,0 +1,47 @@ +#ifndef __SPI_BITBANG_H +#define __SPI_BITBANG_H + +#include <linux/workqueue.h> + +struct spi_bitbang { + spinlock_t lock; + u8 busy; + u8 use_dma; + u8 flags; /* extra spi->mode support */ + + struct spi_master *master; + + /* setup_transfer() changes clock and/or wordsize to match settings + * for this transfer; zeroes restore defaults from spi_device. + */ + int (*setup_transfer)(struct spi_device *spi, + struct spi_transfer *t); + + void (*chipselect)(struct spi_device *spi, int is_on); +#define BITBANG_CS_ACTIVE 1 /* normally nCS, active low */ +#define BITBANG_CS_INACTIVE 0 + + /* txrx_bufs() may handle dma mapping for transfers that don't + * already have one (transfer.{tx,rx}_dma is zero), or use PIO + */ + int (*txrx_bufs)(struct spi_device *spi, struct spi_transfer *t); + + /* txrx_word[SPI_MODE_*]() just looks like a shift register */ + u32 (*txrx_word[4])(struct spi_device *spi, + unsigned nsecs, + u32 word, u8 bits); +}; + +/* you can call these default bitbang->master methods from your custom + * methods, if you like. + */ +extern int spi_bitbang_setup(struct spi_device *spi); +extern void spi_bitbang_cleanup(struct spi_device *spi); +extern int spi_bitbang_setup_transfer(struct spi_device *spi, + struct spi_transfer *t); + +/* start or stop queue processing */ +extern int spi_bitbang_start(struct spi_bitbang *spi); +extern void spi_bitbang_stop(struct spi_bitbang *spi); + +#endif /* __SPI_BITBANG_H */ diff --git a/kernel/include/linux/spi/spi_gpio.h b/kernel/include/linux/spi/spi_gpio.h new file mode 100644 index 000000000..1634ce31c --- /dev/null +++ b/kernel/include/linux/spi/spi_gpio.h @@ -0,0 +1,71 @@ +#ifndef __LINUX_SPI_GPIO_H +#define __LINUX_SPI_GPIO_H + +/* + * For each bitbanged SPI bus, set up a platform_device node with: + * - name "spi_gpio" + * - id the same as the SPI bus number it implements + * - dev.platform data pointing to a struct spi_gpio_platform_data + * + * Or, see the driver code for information about speedups that are + * possible on platforms that support inlined access for GPIOs (no + * spi_gpio_platform_data is used). + * + * Use spi_board_info with these busses in the usual way, being sure + * that the controller_data being the GPIO used for each device's + * chipselect: + * + * static struct spi_board_info ... [] = { + * ... + * // this slave uses GPIO 42 for its chipselect + * .controller_data = (void *) 42, + * ... + * // this one uses GPIO 86 for its chipselect + * .controller_data = (void *) 86, + * ... + * }; + * + * If chipselect is not used (there's only one device on the bus), assign + * SPI_GPIO_NO_CHIPSELECT to the controller_data: + * .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT; + * + * If the MISO or MOSI pin is not available then it should be set to + * SPI_GPIO_NO_MISO or SPI_GPIO_NO_MOSI. + * + * If the bitbanged bus is later switched to a "native" controller, + * that platform_device and controller_data should be removed. + */ + +#define SPI_GPIO_NO_CHIPSELECT ((unsigned long)-1l) +#define SPI_GPIO_NO_MISO ((unsigned long)-1l) +#define SPI_GPIO_NO_MOSI ((unsigned long)-1l) + +/** + * struct spi_gpio_platform_data - parameter for bitbanged SPI master + * @sck: number of the GPIO used for clock output + * @mosi: number of the GPIO used for Master Output, Slave In (MOSI) data + * @miso: number of the GPIO used for Master Input, Slave Output (MISO) data + * @num_chipselect: how many slaves to allow + * + * All GPIO signals used with the SPI bus managed through this driver + * (chipselects, MOSI, MISO, SCK) must be configured as GPIOs, instead + * of some alternate function. + * + * It can be convenient to use this driver with pins that have alternate + * functions associated with a "native" SPI controller if a driver for that + * controller is not available, or is missing important functionality. + * + * On platforms which can do so, configure MISO with a weak pullup unless + * there's an external pullup on that signal. That saves power by avoiding + * floating signals. (A weak pulldown would save power too, but many + * drivers expect to see all-ones data as the no slave "response".) + */ +struct spi_gpio_platform_data { + unsigned sck; + unsigned long mosi; + unsigned long miso; + + u16 num_chipselect; +}; + +#endif /* __LINUX_SPI_GPIO_H */ diff --git a/kernel/include/linux/spi/spi_oc_tiny.h b/kernel/include/linux/spi/spi_oc_tiny.h new file mode 100644 index 000000000..1ac529cf4 --- /dev/null +++ b/kernel/include/linux/spi/spi_oc_tiny.h @@ -0,0 +1,20 @@ +#ifndef _LINUX_SPI_SPI_OC_TINY_H +#define _LINUX_SPI_SPI_OC_TINY_H + +/** + * struct tiny_spi_platform_data - platform data of the OpenCores tiny SPI + * @freq: input clock freq to the core. + * @baudwidth: baud rate divider width of the core. + * @gpio_cs_count: number of gpio pins used for chipselect. + * @gpio_cs: array of gpio pins used for chipselect. + * + * freq and baudwidth are used only if the divider is programmable. + */ +struct tiny_spi_platform_data { + unsigned int freq; + unsigned int baudwidth; + unsigned int gpio_cs_count; + int *gpio_cs; +}; + +#endif /* _LINUX_SPI_SPI_OC_TINY_H */ diff --git a/kernel/include/linux/spi/tdo24m.h b/kernel/include/linux/spi/tdo24m.h new file mode 100644 index 000000000..7572d4e1f --- /dev/null +++ b/kernel/include/linux/spi/tdo24m.h @@ -0,0 +1,13 @@ +#ifndef __TDO24M_H__ +#define __TDO24M_H__ + +enum tdo24m_model { + TDO24M, + TDO35S, +}; + +struct tdo24m_platform_data { + enum tdo24m_model model; +}; + +#endif /* __TDO24M_H__ */ diff --git a/kernel/include/linux/spi/tle62x0.h b/kernel/include/linux/spi/tle62x0.h new file mode 100644 index 000000000..414c6fddf --- /dev/null +++ b/kernel/include/linux/spi/tle62x0.h @@ -0,0 +1,20 @@ +/* + * tle62x0.h - platform glue to Infineon TLE62x0 driver chips + * + * Copyright 2007 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. +*/ + +struct tle62x0_pdata { + unsigned int init_state; + unsigned int gpio_count; +}; diff --git a/kernel/include/linux/spi/tsc2005.h b/kernel/include/linux/spi/tsc2005.h new file mode 100644 index 000000000..563b3b179 --- /dev/null +++ b/kernel/include/linux/spi/tsc2005.h @@ -0,0 +1,34 @@ +/* + * This file is part of TSC2005 touchscreen driver + * + * Copyright (C) 2009-2010 Nokia Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _LINUX_SPI_TSC2005_H +#define _LINUX_SPI_TSC2005_H + +#include <linux/types.h> + +struct tsc2005_platform_data { + int ts_pressure_max; + int ts_pressure_fudge; + int ts_x_max; + int ts_x_fudge; + int ts_y_max; + int ts_y_fudge; + int ts_x_plate_ohm; + unsigned int esd_timeout_ms; + void (*set_reset)(bool enable); +}; + +#endif diff --git a/kernel/include/linux/spi/xilinx_spi.h b/kernel/include/linux/spi/xilinx_spi.h new file mode 100644 index 000000000..333ecdfee --- /dev/null +++ b/kernel/include/linux/spi/xilinx_spi.h @@ -0,0 +1,19 @@ +#ifndef __LINUX_SPI_XILINX_SPI_H +#define __LINUX_SPI_XILINX_SPI_H + +/** + * struct xspi_platform_data - Platform data of the Xilinx SPI driver + * @num_chipselect: Number of chip select by the IP. + * @little_endian: If registers should be accessed little endian or not. + * @bits_per_word: Number of bits per word. + * @devices: Devices to add when the driver is probed. + * @num_devices: Number of devices in the devices array. + */ +struct xspi_platform_data { + u16 num_chipselect; + u8 bits_per_word; + struct spi_board_info *devices; + u8 num_devices; +}; + +#endif /* __LINUX_SPI_XILINX_SPI_H */ |