diff options
Diffstat (limited to 'kernel/include/linux/lis3lv02d.h')
| -rw-r--r-- | kernel/include/linux/lis3lv02d.h | 127 |
1 files changed, 127 insertions, 0 deletions
diff --git a/kernel/include/linux/lis3lv02d.h b/kernel/include/linux/lis3lv02d.h new file mode 100644 index 000000000..f1664c636 --- /dev/null +++ b/kernel/include/linux/lis3lv02d.h @@ -0,0 +1,127 @@ +#ifndef __LIS3LV02D_H_ +#define __LIS3LV02D_H_ + +/** + * struct lis3lv02d_platform_data - lis3 chip family platform data + * @click_flags: Click detection unit configuration + * @click_thresh_x: Click detection unit x axis threshold + * @click_thresh_y: Click detection unit y axis threshold + * @click_thresh_z: Click detection unit z axis threshold + * @click_time_limit: Click detection unit time parameter + * @click_latency: Click detection unit latency parameter + * @click_window: Click detection unit window parameter + * @irq_cfg: On chip irq source and type configuration (click / + * data available / wake up, open drain, polarity) + * @irq_flags1: Additional irq triggering flags for irq channel 0 + * @irq_flags2: Additional irq triggering flags for irq channel 1 + * @duration1: Wake up unit 1 duration parameter + * @duration2: Wake up unit 2 duration parameter + * @wakeup_flags: Wake up unit 1 flags + * @wakeup_thresh: Wake up unit 1 threshold value + * @wakeup_flags2: Wake up unit 2 flags + * @wakeup_thresh2: Wake up unit 2 threshold value + * @hipass_ctrl: High pass filter control (enable / disable, cut off + * frequency) + * @axis_x: Sensor orientation remapping for x-axis + * @axis_y: Sensor orientation remapping for y-axis + * @axis_z: Sensor orientation remapping for z-axis + * @driver_features: Enable bits for different features. Disabled by default + * @default_rate: Default sampling rate. 0 means reset default + * @setup_resources: Interrupt line setup call back function + * @release_resources: Interrupt line release call back function + * @st_min_limits[3]: Selftest acceptance minimum values + * @st_max_limits[3]: Selftest acceptance maximum values + * @irq2: Irq line 2 number + * + * Platform data is used to setup the sensor chip. Meaning of the different + * chip features can be found from the data sheet. It is publicly available + * at www.st.com web pages. Currently the platform data is used + * only for the 8 bit device. The 8 bit device has two wake up / free fall + * detection units and click detection unit. There are plenty of ways to + * configure the chip which makes is quite hard to explain deeper meaning of + * the fields here. Behaviour of the detection blocks varies heavily depending + * on the configuration. For example, interrupt detection block can use high + * pass filtered data which makes it react to the changes in the acceleration. + * Irq_flags can be used to enable interrupt detection on the both edges. + * With proper chip configuration this produces interrupt when some trigger + * starts and when it goes away. + */ + +struct lis3lv02d_platform_data { + /* please note: the 'click' feature is only supported for + * LIS[32]02DL variants of the chip and will be ignored for + * others */ +#define LIS3_CLICK_SINGLE_X (1 << 0) +#define LIS3_CLICK_DOUBLE_X (1 << 1) +#define LIS3_CLICK_SINGLE_Y (1 << 2) +#define LIS3_CLICK_DOUBLE_Y (1 << 3) +#define LIS3_CLICK_SINGLE_Z (1 << 4) +#define LIS3_CLICK_DOUBLE_Z (1 << 5) + unsigned char click_flags; + unsigned char click_thresh_x; + unsigned char click_thresh_y; + unsigned char click_thresh_z; + unsigned char click_time_limit; + unsigned char click_latency; + unsigned char click_window; + +#define LIS3_IRQ1_DISABLE (0 << 0) +#define LIS3_IRQ1_FF_WU_1 (1 << 0) +#define LIS3_IRQ1_FF_WU_2 (2 << 0) +#define LIS3_IRQ1_FF_WU_12 (3 << 0) +#define LIS3_IRQ1_DATA_READY (4 << 0) +#define LIS3_IRQ1_CLICK (7 << 0) +#define LIS3_IRQ1_MASK (7 << 0) +#define LIS3_IRQ2_DISABLE (0 << 3) +#define LIS3_IRQ2_FF_WU_1 (1 << 3) +#define LIS3_IRQ2_FF_WU_2 (2 << 3) +#define LIS3_IRQ2_FF_WU_12 (3 << 3) +#define LIS3_IRQ2_DATA_READY (4 << 3) +#define LIS3_IRQ2_CLICK (7 << 3) +#define LIS3_IRQ2_MASK (7 << 3) +#define LIS3_IRQ_OPEN_DRAIN (1 << 6) +#define LIS3_IRQ_ACTIVE_LOW (1 << 7) + unsigned char irq_cfg; + unsigned char irq_flags1; /* Additional irq edge / level flags */ + unsigned char irq_flags2; /* Additional irq edge / level flags */ + unsigned char duration1; + unsigned char duration2; +#define LIS3_WAKEUP_X_LO (1 << 0) +#define LIS3_WAKEUP_X_HI (1 << 1) +#define LIS3_WAKEUP_Y_LO (1 << 2) +#define LIS3_WAKEUP_Y_HI (1 << 3) +#define LIS3_WAKEUP_Z_LO (1 << 4) +#define LIS3_WAKEUP_Z_HI (1 << 5) + unsigned char wakeup_flags; + unsigned char wakeup_thresh; + unsigned char wakeup_flags2; + unsigned char wakeup_thresh2; +#define LIS3_HIPASS_CUTFF_8HZ 0 +#define LIS3_HIPASS_CUTFF_4HZ 1 +#define LIS3_HIPASS_CUTFF_2HZ 2 +#define LIS3_HIPASS_CUTFF_1HZ 3 +#define LIS3_HIPASS1_DISABLE (1 << 2) +#define LIS3_HIPASS2_DISABLE (1 << 3) + unsigned char hipass_ctrl; +#define LIS3_NO_MAP 0 +#define LIS3_DEV_X 1 +#define LIS3_DEV_Y 2 +#define LIS3_DEV_Z 3 +#define LIS3_INV_DEV_X -1 +#define LIS3_INV_DEV_Y -2 +#define LIS3_INV_DEV_Z -3 + s8 axis_x; + s8 axis_y; + s8 axis_z; +#define LIS3_USE_BLOCK_READ 0x02 + u16 driver_features; + int default_rate; + int (*setup_resources)(void); + int (*release_resources)(void); + /* Limits for selftest are specified in chip data sheet */ + s16 st_min_limits[3]; /* min pass limit x, y, z */ + s16 st_max_limits[3]; /* max pass limit x, y, z */ + int irq2; +}; + +#endif /* __LIS3LV02D_H_ */ |