diff options
Diffstat (limited to 'kernel/drivers/usb/phy/Kconfig')
| -rw-r--r-- | kernel/drivers/usb/phy/Kconfig | 216 |
1 files changed, 216 insertions, 0 deletions
diff --git a/kernel/drivers/usb/phy/Kconfig b/kernel/drivers/usb/phy/Kconfig new file mode 100644 index 000000000..2175678e6 --- /dev/null +++ b/kernel/drivers/usb/phy/Kconfig @@ -0,0 +1,216 @@ +# +# Physical Layer USB driver configuration +# +menu "USB Physical Layer drivers" + +config USB_PHY + def_bool n + +# +# USB Transceiver Drivers +# +config AB8500_USB + tristate "AB8500 USB Transceiver Driver" + depends on AB8500_CORE + select USB_PHY + help + Enable this to support the USB OTG transceiver in AB8500 chip. + This transceiver supports high and full speed devices plus, + in host mode, low speed. + +config FSL_USB2_OTG + bool "Freescale USB OTG Transceiver Driver" + depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM + select USB_OTG + select USB_PHY + help + Enable this to support Freescale USB OTG transceiver. + +config ISP1301_OMAP + tristate "Philips ISP1301 with OMAP OTG" + depends on I2C && ARCH_OMAP_OTG + depends on USB + select USB_PHY + help + If you say yes here you get support for the Philips ISP1301 + USB-On-The-Go transceiver working with the OMAP OTG controller. + The ISP1301 is a full speed USB transceiver which is used in + products including H2, H3, and H4 development boards for Texas + Instruments OMAP processors. + + This driver can also be built as a module. If so, the module + will be called phy-isp1301-omap. + +config KEYSTONE_USB_PHY + tristate "Keystone USB PHY Driver" + depends on ARCH_KEYSTONE || COMPILE_TEST + select NOP_USB_XCEIV + help + Enable this to support Keystone USB phy. This driver provides + interface to interact with USB 2.0 and USB 3.0 PHY that is part + of the Keystone SOC. + +config NOP_USB_XCEIV + tristate "NOP USB Transceiver Driver" + select USB_PHY + help + This driver is to be used by all the usb transceiver which are either + built-in with usb ip or which are autonomous and doesn't require any + phy programming such as ISP1x04 etc. + +config AM335X_CONTROL_USB + tristate + +config AM335X_PHY_USB + tristate "AM335x USB PHY Driver" + depends on ARM || COMPILE_TEST + select USB_PHY + select AM335X_CONTROL_USB + select NOP_USB_XCEIV + help + This driver provides PHY support for that phy which part for the + AM335x SoC. + +config SAMSUNG_USBPHY + tristate + help + Enable this to support Samsung USB phy helper driver for Samsung SoCs. + This driver provides common interface to interact, for Samsung USB 2.0 PHY + driver and later for Samsung USB 3.0 PHY driver. + +config TWL6030_USB + tristate "TWL6030 USB Transceiver Driver" + depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS + help + Enable this to support the USB OTG transceiver on TWL6030 + family chips. This TWL6030 transceiver has the VBUS and ID GND + and OTG SRP events capabilities. For all other transceiver functionality + UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs + are hooked to this driver through platform_data structure. + The definition of internal PHY APIs are in the mach-omap2 layer. + +config USB_GPIO_VBUS + tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" + depends on GPIOLIB + select USB_PHY + help + Provides simple GPIO VBUS sensing for controllers with an + internal transceiver via the usb_phy interface, and + optionally control of a D+ pullup GPIO as well as a VBUS + current limit regulator. + +config OMAP_OTG + tristate "OMAP USB OTG controller driver" + depends on ARCH_OMAP_OTG && EXTCON + help + Enable this to support some transceivers on OMAP1 platforms. OTG + controller is needed to switch between host and peripheral modes. + + This driver can also be built as a module. If so, the module + will be called phy-omap-otg. + +config TAHVO_USB + tristate "Tahvo USB transceiver driver" + depends on MFD_RETU && EXTCON + select USB_PHY + help + Enable this to support USB transceiver on Tahvo. This is used + at least on Nokia 770. + +config TAHVO_USB_HOST_BY_DEFAULT + depends on TAHVO_USB + bool "Device in USB host mode by default" + help + Say Y here, if you want the device to enter USB host mode + by default on bootup. + +config USB_ISP1301 + tristate "NXP ISP1301 USB transceiver support" + depends on USB || USB_GADGET + depends on I2C + select USB_PHY + help + Say Y here to add support for the NXP ISP1301 USB transceiver driver. + This chip is typically used as USB transceiver for USB host, gadget + and OTG drivers (to be selected separately). + + To compile this driver as a module, choose M here: the + module will be called phy-isp1301. + +config USB_MSM_OTG + tristate "Qualcomm on-chip USB OTG controller support" + depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST) + depends on RESET_CONTROLLER + select USB_PHY + help + Enable this to support the USB OTG transceiver on Qualcomm chips. It + handles PHY initialization, clock management, and workarounds + required after resetting the hardware and power management. + This driver is required even for peripheral only or host only + mode configurations. + This driver is not supported on boards like trout which + has an external PHY. + +config USB_MV_OTG + tristate "Marvell USB OTG support" + depends on USB_EHCI_MV && USB_MV_UDC && PM + select USB_OTG + select USB_PHY + help + Say Y here if you want to build Marvell USB OTG transciever + driver in kernel (including PXA and MMP series). This driver + implements role switch between EHCI host driver and gadget driver. + + To compile this driver as a module, choose M here. + +config USB_MXS_PHY + tristate "Freescale MXS USB PHY support" + depends on ARCH_MXC || ARCH_MXS + select STMP_DEVICE + select USB_PHY + help + Enable this to support the Freescale MXS USB PHY. + + MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. + +config USB_RCAR_PHY + tristate "Renesas R-Car USB PHY support" + depends on USB || USB_GADGET + depends on ARCH_R8A7778 || ARCH_R8A7779 || COMPILE_TEST + select USB_PHY + help + Say Y here to add support for the Renesas R-Car USB common PHY driver. + This chip is typically used as USB PHY for USB host, gadget. + This driver supports R8A7778 and R8A7779. + + To compile this driver as a module, choose M here: the + module will be called phy-rcar-usb. + +config USB_RCAR_GEN2_PHY + tristate "Renesas R-Car Gen2 USB PHY support" + depends on ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST + select USB_PHY + help + Say Y here to add support for the Renesas R-Car Gen2 USB PHY driver. + It is typically used to control internal USB PHY for USBHS, + and to configure shared USB channels 0 and 2. + This driver supports R8A7790 and R8A7791. + + To compile this driver as a module, choose M here: the + module will be called phy-rcar-gen2-usb. + +config USB_ULPI + bool "Generic ULPI Transceiver Driver" + depends on ARM || ARM64 + select USB_ULPI_VIEWPORT + help + Enable this to support ULPI connected USB OTG transceivers which + are likely found on embedded boards. + +config USB_ULPI_VIEWPORT + bool + help + Provides read/write operations to the ULPI phy register set for + controllers with a viewport register (e.g. Chipidea/ARC controllers). + +endmenu |