1 files changed, 34 insertions, 50 deletions

diff --git a/kernel/drivers/usb/core/hub.c b/kernel/drivers/usb/core/hub.c
index 3b7151687..1e9a8c9aa 100644
--- a/kernel/drivers/usb/core/hub.c
+++ b/kernel/drivers/usb/core/hub.c
@@ -122,7 +122,7 @@ struct usb_hub *usb_hub_to_struct_hub(struct usb_device *hdev)
 	return usb_get_intfdata(hdev->actconfig->interface[0]);
 }
 
-static int usb_device_supports_lpm(struct usb_device *udev)
+int usb_device_supports_lpm(struct usb_device *udev)
 {
 	/* USB 2.1 (and greater) devices indicate LPM support through
 	 * their USB 2.0 Extended Capabilities BOS descriptor.
@@ -2616,9 +2616,6 @@ static bool use_new_scheme(struct usb_device *udev, int retry)
 	return USE_NEW_SCHEME(retry);
 }
 
-static int hub_port_reset(struct usb_hub *hub, int port1,
-			struct usb_device *udev, unsigned int delay, bool warm);
-
 /* Is a USB 3.0 port in the Inactive or Compliance Mode state?
  * Port worm reset is required to recover
  */
@@ -2706,44 +2703,6 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1,
 	return 0;
 }
 
-static void hub_port_finish_reset(struct usb_hub *hub, int port1,
-			struct usb_device *udev, int *status)
-{
-	switch (*status) {
-	case 0:
-		/* TRSTRCY = 10 ms; plus some extra */
-		msleep(10 + 40);
-		if (udev) {
-			struct usb_hcd *hcd = bus_to_hcd(udev->bus);
-
-			update_devnum(udev, 0);
-			/* The xHC may think the device is already reset,
-			 * so ignore the status.
-			 */
-			if (hcd->driver->reset_device)
-				hcd->driver->reset_device(hcd, udev);
-		}
-		/* FALL THROUGH */
-	case -ENOTCONN:
-	case -ENODEV:
-		usb_clear_port_feature(hub->hdev,
-				port1, USB_PORT_FEAT_C_RESET);
-		if (hub_is_superspeed(hub->hdev)) {
-			usb_clear_port_feature(hub->hdev, port1,
-					USB_PORT_FEAT_C_BH_PORT_RESET);
-			usb_clear_port_feature(hub->hdev, port1,
-					USB_PORT_FEAT_C_PORT_LINK_STATE);
-			usb_clear_port_feature(hub->hdev, port1,
-					USB_PORT_FEAT_C_CONNECTION);
-		}
-		if (udev)
-			usb_set_device_state(udev, *status
-					? USB_STATE_NOTATTACHED
-					: USB_STATE_DEFAULT);
-		break;
-	}
-}
-
 /* Handle port reset and port warm(BH) reset (for USB3 protocol ports) */
 static int hub_port_reset(struct usb_hub *hub, int port1,
 			struct usb_device *udev, unsigned int delay, bool warm)
@@ -2767,13 +2726,10 @@ static int hub_port_reset(struct usb_hub *hub, int port1,
 		 * If the caller hasn't explicitly requested a warm reset,
 		 * double check and see if one is needed.
 		 */
-		status = hub_port_status(hub, port1,
-					&portstatus, &portchange);
-		if (status < 0)
-			goto done;
-
-		if (hub_port_warm_reset_required(hub, port1, portstatus))
-			warm = true;
+		if (hub_port_status(hub, port1, &portstatus, &portchange) == 0)
+			if (hub_port_warm_reset_required(hub, port1,
+							portstatus))
+				warm = true;
 	}
 	clear_bit(port1, hub->warm_reset_bits);
 
@@ -2799,11 +2755,19 @@ static int hub_port_reset(struct usb_hub *hub, int port1,
 
 		/* Check for disconnect or reset */
 		if (status == 0 || status == -ENOTCONN || status == -ENODEV) {
-			hub_port_finish_reset(hub, port1, udev, &status);
+			usb_clear_port_feature(hub->hdev, port1,
+					USB_PORT_FEAT_C_RESET);
 
 			if (!hub_is_superspeed(hub->hdev))
 				goto done;
 
+			usb_clear_port_feature(hub->hdev, port1,
+					USB_PORT_FEAT_C_BH_PORT_RESET);
+			usb_clear_port_feature(hub->hdev, port1,
+					USB_PORT_FEAT_C_PORT_LINK_STATE);
+			usb_clear_port_feature(hub->hdev, port1,
+					USB_PORT_FEAT_C_CONNECTION);
+
 			/*
 			 * If a USB 3.0 device migrates from reset to an error
 			 * state, re-issue the warm reset.
@@ -2836,6 +2800,26 @@ static int hub_port_reset(struct usb_hub *hub, int port1,
 	dev_err(&port_dev->dev, "Cannot enable. Maybe the USB cable is bad?\n");
 
 done:
+	if (status == 0) {
+		/* TRSTRCY = 10 ms; plus some extra */
+		msleep(10 + 40);
+		if (udev) {
+			struct usb_hcd *hcd = bus_to_hcd(udev->bus);
+
+			update_devnum(udev, 0);
+			/* The xHC may think the device is already reset,
+			 * so ignore the status.
+			 */
+			if (hcd->driver->reset_device)
+				hcd->driver->reset_device(hcd, udev);
+
+			usb_set_device_state(udev, USB_STATE_DEFAULT);
+		}
+	} else {
+		if (udev)
+			usb_set_device_state(udev, USB_STATE_NOTATTACHED);
+	}
+
 	if (!hub_is_superspeed(hub->hdev))
 		up_read(&ehci_cf_port_reset_rwsem);