diff options
Diffstat (limited to 'kernel/drivers/tty/serial/8250')
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250.h | 17 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_core.c | 2928 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_dma.c | 10 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_dw.c | 302 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_early.c | 10 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_fintek.c | 172 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_fsl.c | 1 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_ingenic.c | 345 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_lpc18xx.c | 230 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_mid.c | 326 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_mtk.c | 119 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_omap.c | 276 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_pci.c | 382 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_port.c | 2935 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/8250_uniphier.c | 262 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/Kconfig | 48 | ||||
| -rw-r--r-- | kernel/drivers/tty/serial/8250/Makefile | 11 |
17 files changed, 4860 insertions, 3514 deletions
diff --git a/kernel/drivers/tty/serial/8250/8250.h b/kernel/drivers/tty/serial/8250/8250.h index c43f74c53..d54dcd87c 100644 --- a/kernel/drivers/tty/serial/8250/8250.h +++ b/kernel/drivers/tty/serial/8250/8250.h @@ -42,9 +42,9 @@ struct uart_8250_dma { size_t rx_size; size_t tx_size; - unsigned char tx_running:1; - unsigned char tx_err: 1; - unsigned char rx_running:1; + unsigned char tx_running; + unsigned char tx_err; + unsigned char rx_running; }; struct old_serial_port { @@ -211,3 +211,14 @@ static inline int ns16550a_goto_highspeed(struct uart_8250_port *up) } return 1; } + +static inline int serial_index(struct uart_port *port) +{ + return port->minor - 64; +} + +#if 0 +#define DEBUG_INTR(fmt...) printk(fmt) +#else +#define DEBUG_INTR(fmt...) do { } while (0) +#endif diff --git a/kernel/drivers/tty/serial/8250/8250_core.c b/kernel/drivers/tty/serial/8250/8250_core.c index 822a2e197..af7701ca4 100644 --- a/kernel/drivers/tty/serial/8250/8250_core.c +++ b/kernel/drivers/tty/serial/8250/8250_core.c @@ -1,25 +1,23 @@ /* - * Driver for 8250/16550-type serial ports + * Universal/legacy driver for 8250/16550-type serial ports * * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. * * Copyright (C) 2001 Russell King. * + * Supports: ISA-compatible 8250/16550 ports + * PNP 8250/16550 ports + * early_serial_setup() ports + * userspace-configurable "phantom" ports + * "serial8250" platform devices + * serial8250_register_8250_port() ports + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. - * - * A note about mapbase / membase - * - * mapbase is the physical address of the IO port. - * membase is an 'ioremapped' cookie. */ -#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) -#define SUPPORT_SYSRQ -#endif - #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/ioport.h> @@ -36,14 +34,13 @@ #include <linux/nmi.h> #include <linux/mutex.h> #include <linux/slab.h> -#include <linux/kdb.h> #include <linux/uaccess.h> #include <linux/pm_runtime.h> +#include <linux/io.h> #ifdef CONFIG_SPARC #include <linux/sunserialcore.h> #endif -#include <asm/io.h> #include <asm/irq.h> #include "8250.h" @@ -59,29 +56,9 @@ static unsigned int nr_uarts = CONFIG_SERIAL_8250_RUNTIME_UARTS; static struct uart_driver serial8250_reg; -static int serial_index(struct uart_port *port) -{ - return port->minor - 64; -} - static unsigned int skip_txen_test; /* force skip of txen test at init time */ /* - * Debugging. - */ -#if 0 -#define DEBUG_AUTOCONF(fmt...) printk(fmt) -#else -#define DEBUG_AUTOCONF(fmt...) do { } while (0) -#endif - -#if 0 -#define DEBUG_INTR(fmt...) printk(fmt) -#else -#define DEBUG_INTR(fmt...) do { } while (0) -#endif - -/* * On -rt we can have a more delays, and legitimately * so - so don't drop work spuriously and spam the * syslog: @@ -92,22 +69,6 @@ static unsigned int skip_txen_test; /* force skip of txen test at init time */ # define PASS_LIMIT 512 #endif -#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) - - -#ifdef CONFIG_SERIAL_8250_DETECT_IRQ -#define CONFIG_SERIAL_DETECT_IRQ 1 -#endif -#ifdef CONFIG_SERIAL_8250_MANY_PORTS -#define CONFIG_SERIAL_MANY_PORTS 1 -#endif - -/* - * HUB6 is always on. This will be removed once the header - * files have been cleaned. - */ -#define CONFIG_HUB6 1 - #include <asm/serial.h> /* * SERIAL_PORT_DFNS tells us about built-in ports that have no @@ -143,1563 +104,6 @@ static struct hlist_head irq_lists[NR_IRQ_HASH]; static DEFINE_MUTEX(hash_mutex); /* Used to walk the hash */ /* - * Here we define the default xmit fifo size used for each type of UART. - */ -static const struct serial8250_config uart_config[] = { - [PORT_UNKNOWN] = { - .name = "unknown", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_8250] = { - .name = "8250", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16450] = { - .name = "16450", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16550] = { - .name = "16550", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16550A] = { - .name = "16550A", - .fifo_size = 16, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .rxtrig_bytes = {1, 4, 8, 14}, - .flags = UART_CAP_FIFO, - }, - [PORT_CIRRUS] = { - .name = "Cirrus", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16650] = { - .name = "ST16650", - .fifo_size = 1, - .tx_loadsz = 1, - .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, - }, - [PORT_16650V2] = { - .name = "ST16650V2", - .fifo_size = 32, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | - UART_FCR_T_TRIG_00, - .rxtrig_bytes = {8, 16, 24, 28}, - .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, - }, - [PORT_16750] = { - .name = "TI16750", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | - UART_FCR7_64BYTE, - .rxtrig_bytes = {1, 16, 32, 56}, - .flags = UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE, - }, - [PORT_STARTECH] = { - .name = "Startech", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16C950] = { - .name = "16C950/954", - .fifo_size = 128, - .tx_loadsz = 128, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - /* UART_CAP_EFR breaks billionon CF bluetooth card. */ - .flags = UART_CAP_FIFO | UART_CAP_SLEEP, - }, - [PORT_16654] = { - .name = "ST16654", - .fifo_size = 64, - .tx_loadsz = 32, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | - UART_FCR_T_TRIG_10, - .rxtrig_bytes = {8, 16, 56, 60}, - .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, - }, - [PORT_16850] = { - .name = "XR16850", - .fifo_size = 128, - .tx_loadsz = 128, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, - }, - [PORT_RSA] = { - .name = "RSA", - .fifo_size = 2048, - .tx_loadsz = 2048, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11, - .flags = UART_CAP_FIFO, - }, - [PORT_NS16550A] = { - .name = "NS16550A", - .fifo_size = 16, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_NATSEMI, - }, - [PORT_XSCALE] = { - .name = "XScale", - .fifo_size = 32, - .tx_loadsz = 32, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE, - }, - [PORT_OCTEON] = { - .name = "OCTEON", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO, - }, - [PORT_AR7] = { - .name = "AR7", - .fifo_size = 16, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, - [PORT_U6_16550A] = { - .name = "U6_16550A", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, - [PORT_TEGRA] = { - .name = "Tegra", - .fifo_size = 32, - .tx_loadsz = 8, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | - UART_FCR_T_TRIG_01, - .rxtrig_bytes = {1, 4, 8, 14}, - .flags = UART_CAP_FIFO | UART_CAP_RTOIE, - }, - [PORT_XR17D15X] = { - .name = "XR17D15X", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | - UART_CAP_SLEEP, - }, - [PORT_XR17V35X] = { - .name = "XR17V35X", - .fifo_size = 256, - .tx_loadsz = 256, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 | - UART_FCR_T_TRIG_11, - .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | - UART_CAP_SLEEP, - }, - [PORT_LPC3220] = { - .name = "LPC3220", - .fifo_size = 64, - .tx_loadsz = 32, - .fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO | - UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00, - .flags = UART_CAP_FIFO, - }, - [PORT_BRCM_TRUMANAGE] = { - .name = "TruManage", - .fifo_size = 1, - .tx_loadsz = 1024, - .flags = UART_CAP_HFIFO, - }, - [PORT_8250_CIR] = { - .name = "CIR port" - }, - [PORT_ALTR_16550_F32] = { - .name = "Altera 16550 FIFO32", - .fifo_size = 32, - .tx_loadsz = 32, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, - [PORT_ALTR_16550_F64] = { - .name = "Altera 16550 FIFO64", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, - [PORT_ALTR_16550_F128] = { - .name = "Altera 16550 FIFO128", - .fifo_size = 128, - .tx_loadsz = 128, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, -/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement -workaround of errata A-008006 which states that tx_loadsz should be -configured less than Maximum supported fifo bytes */ - [PORT_16550A_FSL64] = { - .name = "16550A_FSL64", - .fifo_size = 64, - .tx_loadsz = 63, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | - UART_FCR7_64BYTE, - .flags = UART_CAP_FIFO, - }, -}; - -/* Uart divisor latch read */ -static int default_serial_dl_read(struct uart_8250_port *up) -{ - return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8; -} - -/* Uart divisor latch write */ -static void default_serial_dl_write(struct uart_8250_port *up, int value) -{ - serial_out(up, UART_DLL, value & 0xff); - serial_out(up, UART_DLM, value >> 8 & 0xff); -} - -#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) - -/* Au1x00/RT288x UART hardware has a weird register layout */ -static const s8 au_io_in_map[8] = { - 0, /* UART_RX */ - 2, /* UART_IER */ - 3, /* UART_IIR */ - 5, /* UART_LCR */ - 6, /* UART_MCR */ - 7, /* UART_LSR */ - 8, /* UART_MSR */ - -1, /* UART_SCR (unmapped) */ -}; - -static const s8 au_io_out_map[8] = { - 1, /* UART_TX */ - 2, /* UART_IER */ - 4, /* UART_FCR */ - 5, /* UART_LCR */ - 6, /* UART_MCR */ - -1, /* UART_LSR (unmapped) */ - -1, /* UART_MSR (unmapped) */ - -1, /* UART_SCR (unmapped) */ -}; - -static unsigned int au_serial_in(struct uart_port *p, int offset) -{ - if (offset >= ARRAY_SIZE(au_io_in_map)) - return UINT_MAX; - offset = au_io_in_map[offset]; - if (offset < 0) - return UINT_MAX; - return __raw_readl(p->membase + (offset << p->regshift)); -} - -static void au_serial_out(struct uart_port *p, int offset, int value) -{ - if (offset >= ARRAY_SIZE(au_io_out_map)) - return; - offset = au_io_out_map[offset]; - if (offset < 0) - return; - __raw_writel(value, p->membase + (offset << p->regshift)); -} - -/* Au1x00 haven't got a standard divisor latch */ -static int au_serial_dl_read(struct uart_8250_port *up) -{ - return __raw_readl(up->port.membase + 0x28); -} - -static void au_serial_dl_write(struct uart_8250_port *up, int value) -{ - __raw_writel(value, up->port.membase + 0x28); -} - -#endif - -static unsigned int hub6_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - outb(p->hub6 - 1 + offset, p->iobase); - return inb(p->iobase + 1); -} - -static void hub6_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - outb(p->hub6 - 1 + offset, p->iobase); - outb(value, p->iobase + 1); -} - -static unsigned int mem_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - return readb(p->membase + offset); -} - -static void mem_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - writeb(value, p->membase + offset); -} - -static void mem32_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - writel(value, p->membase + offset); -} - -static unsigned int mem32_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - return readl(p->membase + offset); -} - -static void mem32be_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - iowrite32be(value, p->membase + offset); -} - -static unsigned int mem32be_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - return ioread32be(p->membase + offset); -} - -static unsigned int io_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - return inb(p->iobase + offset); -} - -static void io_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - outb(value, p->iobase + offset); -} - -static int serial8250_default_handle_irq(struct uart_port *port); -static int exar_handle_irq(struct uart_port *port); - -static void set_io_from_upio(struct uart_port *p) -{ - struct uart_8250_port *up = up_to_u8250p(p); - - up->dl_read = default_serial_dl_read; - up->dl_write = default_serial_dl_write; - - switch (p->iotype) { - case UPIO_HUB6: - p->serial_in = hub6_serial_in; - p->serial_out = hub6_serial_out; - break; - - case UPIO_MEM: - p->serial_in = mem_serial_in; - p->serial_out = mem_serial_out; - break; - - case UPIO_MEM32: - p->serial_in = mem32_serial_in; - p->serial_out = mem32_serial_out; - break; - - case UPIO_MEM32BE: - p->serial_in = mem32be_serial_in; - p->serial_out = mem32be_serial_out; - break; - -#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) - case UPIO_AU: - p->serial_in = au_serial_in; - p->serial_out = au_serial_out; - up->dl_read = au_serial_dl_read; - up->dl_write = au_serial_dl_write; - break; -#endif - - default: - p->serial_in = io_serial_in; - p->serial_out = io_serial_out; - break; - } - /* Remember loaded iotype */ - up->cur_iotype = p->iotype; - p->handle_irq = serial8250_default_handle_irq; -} - -static void -serial_port_out_sync(struct uart_port *p, int offset, int value) -{ - switch (p->iotype) { - case UPIO_MEM: - case UPIO_MEM32: - case UPIO_MEM32BE: - case UPIO_AU: - p->serial_out(p, offset, value); - p->serial_in(p, UART_LCR); /* safe, no side-effects */ - break; - default: - p->serial_out(p, offset, value); - } -} - -/* - * For the 16C950 - */ -static void serial_icr_write(struct uart_8250_port *up, int offset, int value) -{ - serial_out(up, UART_SCR, offset); - serial_out(up, UART_ICR, value); -} - -static unsigned int serial_icr_read(struct uart_8250_port *up, int offset) -{ - unsigned int value; - - serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD); - serial_out(up, UART_SCR, offset); - value = serial_in(up, UART_ICR); - serial_icr_write(up, UART_ACR, up->acr); - - return value; -} - -/* - * FIFO support. - */ -static void serial8250_clear_fifos(struct uart_8250_port *p) -{ - if (p->capabilities & UART_CAP_FIFO) { - serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO); - serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO | - UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); - serial_out(p, UART_FCR, 0); - } -} - -void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p) -{ - serial8250_clear_fifos(p); - serial_out(p, UART_FCR, p->fcr); -} -EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos); - -void serial8250_rpm_get(struct uart_8250_port *p) -{ - if (!(p->capabilities & UART_CAP_RPM)) - return; - pm_runtime_get_sync(p->port.dev); -} -EXPORT_SYMBOL_GPL(serial8250_rpm_get); - -void serial8250_rpm_put(struct uart_8250_port *p) -{ - if (!(p->capabilities & UART_CAP_RPM)) - return; - pm_runtime_mark_last_busy(p->port.dev); - pm_runtime_put_autosuspend(p->port.dev); -} -EXPORT_SYMBOL_GPL(serial8250_rpm_put); - -/* - * These two wrappers ensure that enable_runtime_pm_tx() can be called more than - * once and disable_runtime_pm_tx() will still disable RPM because the fifo is - * empty and the HW can idle again. - */ -static void serial8250_rpm_get_tx(struct uart_8250_port *p) -{ - unsigned char rpm_active; - - if (!(p->capabilities & UART_CAP_RPM)) - return; - - rpm_active = xchg(&p->rpm_tx_active, 1); - if (rpm_active) - return; - pm_runtime_get_sync(p->port.dev); -} - -static void serial8250_rpm_put_tx(struct uart_8250_port *p) -{ - unsigned char rpm_active; - - if (!(p->capabilities & UART_CAP_RPM)) - return; - - rpm_active = xchg(&p->rpm_tx_active, 0); - if (!rpm_active) - return; - pm_runtime_mark_last_busy(p->port.dev); - pm_runtime_put_autosuspend(p->port.dev); -} - -/* - * IER sleep support. UARTs which have EFRs need the "extended - * capability" bit enabled. Note that on XR16C850s, we need to - * reset LCR to write to IER. - */ -static void serial8250_set_sleep(struct uart_8250_port *p, int sleep) -{ - unsigned char lcr = 0, efr = 0; - /* - * Exar UARTs have a SLEEP register that enables or disables - * each UART to enter sleep mode separately. On the XR17V35x the - * register is accessible to each UART at the UART_EXAR_SLEEP - * offset but the UART channel may only write to the corresponding - * bit. - */ - serial8250_rpm_get(p); - if ((p->port.type == PORT_XR17V35X) || - (p->port.type == PORT_XR17D15X)) { - serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0); - goto out; - } - - if (p->capabilities & UART_CAP_SLEEP) { - if (p->capabilities & UART_CAP_EFR) { - lcr = serial_in(p, UART_LCR); - efr = serial_in(p, UART_EFR); - serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(p, UART_EFR, UART_EFR_ECB); - serial_out(p, UART_LCR, 0); - } - serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0); - if (p->capabilities & UART_CAP_EFR) { - serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(p, UART_EFR, efr); - serial_out(p, UART_LCR, lcr); - } - } -out: - serial8250_rpm_put(p); -} - -#ifdef CONFIG_SERIAL_8250_RSA -/* - * Attempts to turn on the RSA FIFO. Returns zero on failure. - * We set the port uart clock rate if we succeed. - */ -static int __enable_rsa(struct uart_8250_port *up) -{ - unsigned char mode; - int result; - - mode = serial_in(up, UART_RSA_MSR); - result = mode & UART_RSA_MSR_FIFO; - - if (!result) { - serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO); - mode = serial_in(up, UART_RSA_MSR); - result = mode & UART_RSA_MSR_FIFO; - } - - if (result) - up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16; - - return result; -} - -static void enable_rsa(struct uart_8250_port *up) -{ - if (up->port.type == PORT_RSA) { - if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) { - spin_lock_irq(&up->port.lock); - __enable_rsa(up); - spin_unlock_irq(&up->port.lock); - } - if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) - serial_out(up, UART_RSA_FRR, 0); - } -} - -/* - * Attempts to turn off the RSA FIFO. Returns zero on failure. - * It is unknown why interrupts were disabled in here. However, - * the caller is expected to preserve this behaviour by grabbing - * the spinlock before calling this function. - */ -static void disable_rsa(struct uart_8250_port *up) -{ - unsigned char mode; - int result; - - if (up->port.type == PORT_RSA && - up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) { - spin_lock_irq(&up->port.lock); - - mode = serial_in(up, UART_RSA_MSR); - result = !(mode & UART_RSA_MSR_FIFO); - - if (!result) { - serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO); - mode = serial_in(up, UART_RSA_MSR); - result = !(mode & UART_RSA_MSR_FIFO); - } - - if (result) - up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16; - spin_unlock_irq(&up->port.lock); - } -} -#endif /* CONFIG_SERIAL_8250_RSA */ - -/* - * This is a quickie test to see how big the FIFO is. - * It doesn't work at all the time, more's the pity. - */ -static int size_fifo(struct uart_8250_port *up) -{ - unsigned char old_fcr, old_mcr, old_lcr; - unsigned short old_dl; - int count; - - old_lcr = serial_in(up, UART_LCR); - serial_out(up, UART_LCR, 0); - old_fcr = serial_in(up, UART_FCR); - old_mcr = serial_in(up, UART_MCR); - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | - UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); - serial_out(up, UART_MCR, UART_MCR_LOOP); - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - old_dl = serial_dl_read(up); - serial_dl_write(up, 0x0001); - serial_out(up, UART_LCR, 0x03); - for (count = 0; count < 256; count++) - serial_out(up, UART_TX, count); - mdelay(20);/* FIXME - schedule_timeout */ - for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) && - (count < 256); count++) - serial_in(up, UART_RX); - serial_out(up, UART_FCR, old_fcr); - serial_out(up, UART_MCR, old_mcr); - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - serial_dl_write(up, old_dl); - serial_out(up, UART_LCR, old_lcr); - - return count; -} - -/* - * Read UART ID using the divisor method - set DLL and DLM to zero - * and the revision will be in DLL and device type in DLM. We - * preserve the device state across this. - */ -static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p) -{ - unsigned char old_dll, old_dlm, old_lcr; - unsigned int id; - - old_lcr = serial_in(p, UART_LCR); - serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A); - - old_dll = serial_in(p, UART_DLL); - old_dlm = serial_in(p, UART_DLM); - - serial_out(p, UART_DLL, 0); - serial_out(p, UART_DLM, 0); - - id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8; - - serial_out(p, UART_DLL, old_dll); - serial_out(p, UART_DLM, old_dlm); - serial_out(p, UART_LCR, old_lcr); - - return id; -} - -/* - * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's. - * When this function is called we know it is at least a StarTech - * 16650 V2, but it might be one of several StarTech UARTs, or one of - * its clones. (We treat the broken original StarTech 16650 V1 as a - * 16550, and why not? Startech doesn't seem to even acknowledge its - * existence.) - * - * What evil have men's minds wrought... - */ -static void autoconfig_has_efr(struct uart_8250_port *up) -{ - unsigned int id1, id2, id3, rev; - - /* - * Everything with an EFR has SLEEP - */ - up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; - - /* - * First we check to see if it's an Oxford Semiconductor UART. - * - * If we have to do this here because some non-National - * Semiconductor clone chips lock up if you try writing to the - * LSR register (which serial_icr_read does) - */ - - /* - * Check for Oxford Semiconductor 16C950. - * - * EFR [4] must be set else this test fails. - * - * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca) - * claims that it's needed for 952 dual UART's (which are not - * recommended for new designs). - */ - up->acr = 0; - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, UART_EFR_ECB); - serial_out(up, UART_LCR, 0x00); - id1 = serial_icr_read(up, UART_ID1); - id2 = serial_icr_read(up, UART_ID2); - id3 = serial_icr_read(up, UART_ID3); - rev = serial_icr_read(up, UART_REV); - - DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev); - - if (id1 == 0x16 && id2 == 0xC9 && - (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) { - up->port.type = PORT_16C950; - - /* - * Enable work around for the Oxford Semiconductor 952 rev B - * chip which causes it to seriously miscalculate baud rates - * when DLL is 0. - */ - if (id3 == 0x52 && rev == 0x01) - up->bugs |= UART_BUG_QUOT; - return; - } - - /* - * We check for a XR16C850 by setting DLL and DLM to 0, and then - * reading back DLL and DLM. The chip type depends on the DLM - * value read back: - * 0x10 - XR16C850 and the DLL contains the chip revision. - * 0x12 - XR16C2850. - * 0x14 - XR16C854. - */ - id1 = autoconfig_read_divisor_id(up); - DEBUG_AUTOCONF("850id=%04x ", id1); - - id2 = id1 >> 8; - if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) { - up->port.type = PORT_16850; - return; - } - - /* - * It wasn't an XR16C850. - * - * We distinguish between the '654 and the '650 by counting - * how many bytes are in the FIFO. I'm using this for now, - * since that's the technique that was sent to me in the - * serial driver update, but I'm not convinced this works. - * I've had problems doing this in the past. -TYT - */ - if (size_fifo(up) == 64) - up->port.type = PORT_16654; - else - up->port.type = PORT_16650V2; -} - -/* - * We detected a chip without a FIFO. Only two fall into - * this category - the original 8250 and the 16450. The - * 16450 has a scratch register (accessible with LCR=0) - */ -static void autoconfig_8250(struct uart_8250_port *up) -{ - unsigned char scratch, status1, status2; - - up->port.type = PORT_8250; - - scratch = serial_in(up, UART_SCR); - serial_out(up, UART_SCR, 0xa5); - status1 = serial_in(up, UART_SCR); - serial_out(up, UART_SCR, 0x5a); - status2 = serial_in(up, UART_SCR); - serial_out(up, UART_SCR, scratch); - - if (status1 == 0xa5 && status2 == 0x5a) - up->port.type = PORT_16450; -} - -static int broken_efr(struct uart_8250_port *up) -{ - /* - * Exar ST16C2550 "A2" devices incorrectly detect as - * having an EFR, and report an ID of 0x0201. See - * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html - */ - if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16) - return 1; - - return 0; -} - -/* - * We know that the chip has FIFOs. Does it have an EFR? The - * EFR is located in the same register position as the IIR and - * we know the top two bits of the IIR are currently set. The - * EFR should contain zero. Try to read the EFR. - */ -static void autoconfig_16550a(struct uart_8250_port *up) -{ - unsigned char status1, status2; - unsigned int iersave; - - up->port.type = PORT_16550A; - up->capabilities |= UART_CAP_FIFO; - - /* - * XR17V35x UARTs have an extra divisor register, DLD - * that gets enabled with when DLAB is set which will - * cause the device to incorrectly match and assign - * port type to PORT_16650. The EFR for this UART is - * found at offset 0x09. Instead check the Deice ID (DVID) - * register for a 2, 4 or 8 port UART. - */ - if (up->port.flags & UPF_EXAR_EFR) { - status1 = serial_in(up, UART_EXAR_DVID); - if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) { - DEBUG_AUTOCONF("Exar XR17V35x "); - up->port.type = PORT_XR17V35X; - up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | - UART_CAP_SLEEP; - - return; - } - - } - - /* - * Check for presence of the EFR when DLAB is set. - * Only ST16C650V1 UARTs pass this test. - */ - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - if (serial_in(up, UART_EFR) == 0) { - serial_out(up, UART_EFR, 0xA8); - if (serial_in(up, UART_EFR) != 0) { - DEBUG_AUTOCONF("EFRv1 "); - up->port.type = PORT_16650; - up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; - } else { - serial_out(up, UART_LCR, 0); - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | - UART_FCR7_64BYTE); - status1 = serial_in(up, UART_IIR) >> 5; - serial_out(up, UART_FCR, 0); - serial_out(up, UART_LCR, 0); - - if (status1 == 7) - up->port.type = PORT_16550A_FSL64; - else - DEBUG_AUTOCONF("Motorola 8xxx DUART "); - } - serial_out(up, UART_EFR, 0); - return; - } - - /* - * Maybe it requires 0xbf to be written to the LCR. - * (other ST16C650V2 UARTs, TI16C752A, etc) - */ - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) { - DEBUG_AUTOCONF("EFRv2 "); - autoconfig_has_efr(up); - return; - } - - /* - * Check for a National Semiconductor SuperIO chip. - * Attempt to switch to bank 2, read the value of the LOOP bit - * from EXCR1. Switch back to bank 0, change it in MCR. Then - * switch back to bank 2, read it from EXCR1 again and check - * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2 - */ - serial_out(up, UART_LCR, 0); - status1 = serial_in(up, UART_MCR); - serial_out(up, UART_LCR, 0xE0); - status2 = serial_in(up, 0x02); /* EXCR1 */ - - if (!((status2 ^ status1) & UART_MCR_LOOP)) { - serial_out(up, UART_LCR, 0); - serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP); - serial_out(up, UART_LCR, 0xE0); - status2 = serial_in(up, 0x02); /* EXCR1 */ - serial_out(up, UART_LCR, 0); - serial_out(up, UART_MCR, status1); - - if ((status2 ^ status1) & UART_MCR_LOOP) { - unsigned short quot; - - serial_out(up, UART_LCR, 0xE0); - - quot = serial_dl_read(up); - quot <<= 3; - - if (ns16550a_goto_highspeed(up)) - serial_dl_write(up, quot); - - serial_out(up, UART_LCR, 0); - - up->port.uartclk = 921600*16; - up->port.type = PORT_NS16550A; - up->capabilities |= UART_NATSEMI; - return; - } - } - - /* - * No EFR. Try to detect a TI16750, which only sets bit 5 of - * the IIR when 64 byte FIFO mode is enabled when DLAB is set. - * Try setting it with and without DLAB set. Cheap clones - * set bit 5 without DLAB set. - */ - serial_out(up, UART_LCR, 0); - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); - status1 = serial_in(up, UART_IIR) >> 5; - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); - status2 = serial_in(up, UART_IIR) >> 5; - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); - serial_out(up, UART_LCR, 0); - - DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2); - - if (status1 == 6 && status2 == 7) { - up->port.type = PORT_16750; - up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP; - return; - } - - /* - * Try writing and reading the UART_IER_UUE bit (b6). - * If it works, this is probably one of the Xscale platform's - * internal UARTs. - * We're going to explicitly set the UUE bit to 0 before - * trying to write and read a 1 just to make sure it's not - * already a 1 and maybe locked there before we even start start. - */ - iersave = serial_in(up, UART_IER); - serial_out(up, UART_IER, iersave & ~UART_IER_UUE); - if (!(serial_in(up, UART_IER) & UART_IER_UUE)) { - /* - * OK it's in a known zero state, try writing and reading - * without disturbing the current state of the other bits. - */ - serial_out(up, UART_IER, iersave | UART_IER_UUE); - if (serial_in(up, UART_IER) & UART_IER_UUE) { - /* - * It's an Xscale. - * We'll leave the UART_IER_UUE bit set to 1 (enabled). - */ - DEBUG_AUTOCONF("Xscale "); - up->port.type = PORT_XSCALE; - up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE; - return; - } - } else { - /* - * If we got here we couldn't force the IER_UUE bit to 0. - * Log it and continue. - */ - DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 "); - } - serial_out(up, UART_IER, iersave); - - /* - * Exar uarts have EFR in a weird location - */ - if (up->port.flags & UPF_EXAR_EFR) { - DEBUG_AUTOCONF("Exar XR17D15x "); - up->port.type = PORT_XR17D15X; - up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | - UART_CAP_SLEEP; - - return; - } - - /* - * We distinguish between 16550A and U6 16550A by counting - * how many bytes are in the FIFO. - */ - if (up->port.type == PORT_16550A && size_fifo(up) == 64) { - up->port.type = PORT_U6_16550A; - up->capabilities |= UART_CAP_AFE; - } -} - -/* - * This routine is called by rs_init() to initialize a specific serial - * port. It determines what type of UART chip this serial port is - * using: 8250, 16450, 16550, 16550A. The important question is - * whether or not this UART is a 16550A or not, since this will - * determine whether or not we can use its FIFO features or not. - */ -static void autoconfig(struct uart_8250_port *up) -{ - unsigned char status1, scratch, scratch2, scratch3; - unsigned char save_lcr, save_mcr; - struct uart_port *port = &up->port; - unsigned long flags; - unsigned int old_capabilities; - - if (!port->iobase && !port->mapbase && !port->membase) - return; - - DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ", - serial_index(port), port->iobase, port->membase); - - /* - * We really do need global IRQs disabled here - we're going to - * be frobbing the chips IRQ enable register to see if it exists. - */ - spin_lock_irqsave(&port->lock, flags); - - up->capabilities = 0; - up->bugs = 0; - - if (!(port->flags & UPF_BUGGY_UART)) { - /* - * Do a simple existence test first; if we fail this, - * there's no point trying anything else. - * - * 0x80 is used as a nonsense port to prevent against - * false positives due to ISA bus float. The - * assumption is that 0x80 is a non-existent port; - * which should be safe since include/asm/io.h also - * makes this assumption. - * - * Note: this is safe as long as MCR bit 4 is clear - * and the device is in "PC" mode. - */ - scratch = serial_in(up, UART_IER); - serial_out(up, UART_IER, 0); -#ifdef __i386__ - outb(0xff, 0x080); -#endif - /* - * Mask out IER[7:4] bits for test as some UARTs (e.g. TL - * 16C754B) allow only to modify them if an EFR bit is set. - */ - scratch2 = serial_in(up, UART_IER) & 0x0f; - serial_out(up, UART_IER, 0x0F); -#ifdef __i386__ - outb(0, 0x080); -#endif - scratch3 = serial_in(up, UART_IER) & 0x0f; - serial_out(up, UART_IER, scratch); - if (scratch2 != 0 || scratch3 != 0x0F) { - /* - * We failed; there's nothing here - */ - spin_unlock_irqrestore(&port->lock, flags); - DEBUG_AUTOCONF("IER test failed (%02x, %02x) ", - scratch2, scratch3); - goto out; - } - } - - save_mcr = serial_in(up, UART_MCR); - save_lcr = serial_in(up, UART_LCR); - - /* - * Check to see if a UART is really there. Certain broken - * internal modems based on the Rockwell chipset fail this - * test, because they apparently don't implement the loopback - * test mode. So this test is skipped on the COM 1 through - * COM 4 ports. This *should* be safe, since no board - * manufacturer would be stupid enough to design a board - * that conflicts with COM 1-4 --- we hope! - */ - if (!(port->flags & UPF_SKIP_TEST)) { - serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A); - status1 = serial_in(up, UART_MSR) & 0xF0; - serial_out(up, UART_MCR, save_mcr); - if (status1 != 0x90) { - spin_unlock_irqrestore(&port->lock, flags); - DEBUG_AUTOCONF("LOOP test failed (%02x) ", - status1); - goto out; - } - } - - /* - * We're pretty sure there's a port here. Lets find out what - * type of port it is. The IIR top two bits allows us to find - * out if it's 8250 or 16450, 16550, 16550A or later. This - * determines what we test for next. - * - * We also initialise the EFR (if any) to zero for later. The - * EFR occupies the same register location as the FCR and IIR. - */ - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, 0); - serial_out(up, UART_LCR, 0); - - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); - scratch = serial_in(up, UART_IIR) >> 6; - - switch (scratch) { - case 0: - autoconfig_8250(up); - break; - case 1: - port->type = PORT_UNKNOWN; - break; - case 2: - port->type = PORT_16550; - break; - case 3: - autoconfig_16550a(up); - break; - } - -#ifdef CONFIG_SERIAL_8250_RSA - /* - * Only probe for RSA ports if we got the region. - */ - if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA && - __enable_rsa(up)) - port->type = PORT_RSA; -#endif - - serial_out(up, UART_LCR, save_lcr); - - port->fifosize = uart_config[up->port.type].fifo_size; - old_capabilities = up->capabilities; - up->capabilities = uart_config[port->type].flags; - up->tx_loadsz = uart_config[port->type].tx_loadsz; - - if (port->type == PORT_UNKNOWN) - goto out_lock; - - /* - * Reset the UART. - */ -#ifdef CONFIG_SERIAL_8250_RSA - if (port->type == PORT_RSA) - serial_out(up, UART_RSA_FRR, 0); -#endif - serial_out(up, UART_MCR, save_mcr); - serial8250_clear_fifos(up); - serial_in(up, UART_RX); - if (up->capabilities & UART_CAP_UUE) - serial_out(up, UART_IER, UART_IER_UUE); - else - serial_out(up, UART_IER, 0); - -out_lock: - spin_unlock_irqrestore(&port->lock, flags); - if (up->capabilities != old_capabilities) { - printk(KERN_WARNING - "ttyS%d: detected caps %08x should be %08x\n", - serial_index(port), old_capabilities, - up->capabilities); - } -out: - DEBUG_AUTOCONF("iir=%d ", scratch); - DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name); -} - -static void autoconfig_irq(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - unsigned char save_mcr, save_ier; - unsigned char save_ICP = 0; - unsigned int ICP = 0; - unsigned long irqs; - int irq; - - if (port->flags & UPF_FOURPORT) { - ICP = (port->iobase & 0xfe0) | 0x1f; - save_ICP = inb_p(ICP); - outb_p(0x80, ICP); - inb_p(ICP); - } - - /* forget possible initially masked and pending IRQ */ - probe_irq_off(probe_irq_on()); - save_mcr = serial_in(up, UART_MCR); - save_ier = serial_in(up, UART_IER); - serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2); - - irqs = probe_irq_on(); - serial_out(up, UART_MCR, 0); - udelay(10); - if (port->flags & UPF_FOURPORT) { - serial_out(up, UART_MCR, - UART_MCR_DTR | UART_MCR_RTS); - } else { - serial_out(up, UART_MCR, - UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2); - } - serial_out(up, UART_IER, 0x0f); /* enable all intrs */ - serial_in(up, UART_LSR); - serial_in(up, UART_RX); - serial_in(up, UART_IIR); - serial_in(up, UART_MSR); - serial_out(up, UART_TX, 0xFF); - udelay(20); - irq = probe_irq_off(irqs); - - serial_out(up, UART_MCR, save_mcr); - serial_out(up, UART_IER, save_ier); - - if (port->flags & UPF_FOURPORT) - outb_p(save_ICP, ICP); - - port->irq = (irq > 0) ? irq : 0; -} - -static inline void __stop_tx(struct uart_8250_port *p) -{ - if (p->ier & UART_IER_THRI) { - p->ier &= ~UART_IER_THRI; - serial_out(p, UART_IER, p->ier); - serial8250_rpm_put_tx(p); - } -} - -static void serial8250_stop_tx(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_rpm_get(up); - __stop_tx(up); - - /* - * We really want to stop the transmitter from sending. - */ - if (port->type == PORT_16C950) { - up->acr |= UART_ACR_TXDIS; - serial_icr_write(up, UART_ACR, up->acr); - } - serial8250_rpm_put(up); -} - -static void serial8250_start_tx(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_rpm_get_tx(up); - - if (up->dma && !up->dma->tx_dma(up)) - return; - - if (!(up->ier & UART_IER_THRI)) { - up->ier |= UART_IER_THRI; - serial_port_out(port, UART_IER, up->ier); - - if (up->bugs & UART_BUG_TXEN) { - unsigned char lsr; - lsr = serial_in(up, UART_LSR); - up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; - if (lsr & UART_LSR_THRE) - serial8250_tx_chars(up); - } - } - - /* - * Re-enable the transmitter if we disabled it. - */ - if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) { - up->acr &= ~UART_ACR_TXDIS; - serial_icr_write(up, UART_ACR, up->acr); - } -} - -static void serial8250_throttle(struct uart_port *port) -{ - port->throttle(port); -} - -static void serial8250_unthrottle(struct uart_port *port) -{ - port->unthrottle(port); -} - -static void serial8250_stop_rx(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_rpm_get(up); - - up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); - up->port.read_status_mask &= ~UART_LSR_DR; - serial_port_out(port, UART_IER, up->ier); - - serial8250_rpm_put(up); -} - -static void serial8250_disable_ms(struct uart_port *port) -{ - struct uart_8250_port *up = - container_of(port, struct uart_8250_port, port); - - /* no MSR capabilities */ - if (up->bugs & UART_BUG_NOMSR) - return; - - up->ier &= ~UART_IER_MSI; - serial_port_out(port, UART_IER, up->ier); -} - -static void serial8250_enable_ms(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - /* no MSR capabilities */ - if (up->bugs & UART_BUG_NOMSR) - return; - - up->ier |= UART_IER_MSI; - - serial8250_rpm_get(up); - serial_port_out(port, UART_IER, up->ier); - serial8250_rpm_put(up); -} - -/* - * serial8250_rx_chars: processes according to the passed in LSR - * value, and returns the remaining LSR bits not handled - * by this Rx routine. - */ -unsigned char -serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr) -{ - struct uart_port *port = &up->port; - unsigned char ch; - int max_count = 256; - char flag; - - do { - if (likely(lsr & UART_LSR_DR)) - ch = serial_in(up, UART_RX); - else - /* - * Intel 82571 has a Serial Over Lan device that will - * set UART_LSR_BI without setting UART_LSR_DR when - * it receives a break. To avoid reading from the - * receive buffer without UART_LSR_DR bit set, we - * just force the read character to be 0 - */ - ch = 0; - - flag = TTY_NORMAL; - port->icount.rx++; - - lsr |= up->lsr_saved_flags; - up->lsr_saved_flags = 0; - - if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) { - if (lsr & UART_LSR_BI) { - lsr &= ~(UART_LSR_FE | UART_LSR_PE); - port->icount.brk++; - /* - * We do the SysRQ and SAK checking - * here because otherwise the break - * may get masked by ignore_status_mask - * or read_status_mask. - */ - if (uart_handle_break(port)) - goto ignore_char; - } else if (lsr & UART_LSR_PE) - port->icount.parity++; - else if (lsr & UART_LSR_FE) - port->icount.frame++; - if (lsr & UART_LSR_OE) - port->icount.overrun++; - - /* - * Mask off conditions which should be ignored. - */ - lsr &= port->read_status_mask; - - if (lsr & UART_LSR_BI) { - DEBUG_INTR("handling break...."); - flag = TTY_BREAK; - } else if (lsr & UART_LSR_PE) - flag = TTY_PARITY; - else if (lsr & UART_LSR_FE) - flag = TTY_FRAME; - } - if (uart_handle_sysrq_char(port, ch)) - goto ignore_char; - - uart_insert_char(port, lsr, UART_LSR_OE, ch, flag); - -ignore_char: - lsr = serial_in(up, UART_LSR); - } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0)); - spin_unlock(&port->lock); - tty_flip_buffer_push(&port->state->port); - spin_lock(&port->lock); - return lsr; -} -EXPORT_SYMBOL_GPL(serial8250_rx_chars); - -void serial8250_tx_chars(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - struct circ_buf *xmit = &port->state->xmit; - int count; - - if (port->x_char) { - serial_out(up, UART_TX, port->x_char); - port->icount.tx++; - port->x_char = 0; - return; - } - if (uart_tx_stopped(port)) { - serial8250_stop_tx(port); - return; - } - if (uart_circ_empty(xmit)) { - __stop_tx(up); - return; - } - - count = up->tx_loadsz; - do { - serial_out(up, UART_TX, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - port->icount.tx++; - if (uart_circ_empty(xmit)) - break; - if (up->capabilities & UART_CAP_HFIFO) { - if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) != - BOTH_EMPTY) - break; - } - } while (--count > 0); - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(port); - - DEBUG_INTR("THRE..."); - - /* - * With RPM enabled, we have to wait until the FIFO is empty before the - * HW can go idle. So we get here once again with empty FIFO and disable - * the interrupt and RPM in __stop_tx() - */ - if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM)) - __stop_tx(up); -} -EXPORT_SYMBOL_GPL(serial8250_tx_chars); - -/* Caller holds uart port lock */ -unsigned int serial8250_modem_status(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - unsigned int status = serial_in(up, UART_MSR); - - status |= up->msr_saved_flags; - up->msr_saved_flags = 0; - if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI && - port->state != NULL) { - if (status & UART_MSR_TERI) - port->icount.rng++; - if (status & UART_MSR_DDSR) - port->icount.dsr++; - if (status & UART_MSR_DDCD) - uart_handle_dcd_change(port, status & UART_MSR_DCD); - if (status & UART_MSR_DCTS) - uart_handle_cts_change(port, status & UART_MSR_CTS); - - wake_up_interruptible(&port->state->port.delta_msr_wait); - } - - return status; -} -EXPORT_SYMBOL_GPL(serial8250_modem_status); - -/* - * This handles the interrupt from one port. - */ -int serial8250_handle_irq(struct uart_port *port, unsigned int iir) -{ - unsigned char status; - unsigned long flags; - struct uart_8250_port *up = up_to_u8250p(port); - int dma_err = 0; - - if (iir & UART_IIR_NO_INT) - return 0; - - spin_lock_irqsave(&port->lock, flags); - - status = serial_port_in(port, UART_LSR); - - DEBUG_INTR("status = %x...", status); - - if (status & (UART_LSR_DR | UART_LSR_BI)) { - if (up->dma) - dma_err = up->dma->rx_dma(up, iir); - - if (!up->dma || dma_err) - status = serial8250_rx_chars(up, status); - } - serial8250_modem_status(up); - if ((!up->dma || (up->dma && up->dma->tx_err)) && - (status & UART_LSR_THRE)) - serial8250_tx_chars(up); - - spin_unlock_irqrestore(&port->lock, flags); - return 1; -} -EXPORT_SYMBOL_GPL(serial8250_handle_irq); - -static int serial8250_default_handle_irq(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned int iir; - int ret; - - serial8250_rpm_get(up); - - iir = serial_port_in(port, UART_IIR); - ret = serial8250_handle_irq(port, iir); - - serial8250_rpm_put(up); - return ret; -} - -/* - * These Exar UARTs have an extra interrupt indicator that could - * fire for a few unimplemented interrupts. One of which is a - * wakeup event when coming out of sleep. Put this here just - * to be on the safe side that these interrupts don't go unhandled. - */ -static int exar_handle_irq(struct uart_port *port) -{ - unsigned char int0, int1, int2, int3; - unsigned int iir = serial_port_in(port, UART_IIR); - int ret; - - ret = serial8250_handle_irq(port, iir); - - if ((port->type == PORT_XR17V35X) || - (port->type == PORT_XR17D15X)) { - int0 = serial_port_in(port, 0x80); - int1 = serial_port_in(port, 0x81); - int2 = serial_port_in(port, 0x82); - int3 = serial_port_in(port, 0x83); - } - - return ret; -} - -/* * This is the serial driver's interrupt routine. * * Arjan thinks the old way was overly complex, so it got simplified. @@ -1964,875 +368,6 @@ static void univ8250_release_irq(struct uart_8250_port *up) serial_unlink_irq_chain(up); } -static unsigned int serial8250_tx_empty(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned long flags; - unsigned int lsr; - - serial8250_rpm_get(up); - - spin_lock_irqsave(&port->lock, flags); - lsr = serial_port_in(port, UART_LSR); - up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; - spin_unlock_irqrestore(&port->lock, flags); - - serial8250_rpm_put(up); - - return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0; -} - -static unsigned int serial8250_get_mctrl(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned int status; - unsigned int ret; - - serial8250_rpm_get(up); - status = serial8250_modem_status(up); - serial8250_rpm_put(up); - - ret = 0; - if (status & UART_MSR_DCD) - ret |= TIOCM_CAR; - if (status & UART_MSR_RI) - ret |= TIOCM_RNG; - if (status & UART_MSR_DSR) - ret |= TIOCM_DSR; - if (status & UART_MSR_CTS) - ret |= TIOCM_CTS; - return ret; -} - -void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned char mcr = 0; - - if (mctrl & TIOCM_RTS) - mcr |= UART_MCR_RTS; - if (mctrl & TIOCM_DTR) - mcr |= UART_MCR_DTR; - if (mctrl & TIOCM_OUT1) - mcr |= UART_MCR_OUT1; - if (mctrl & TIOCM_OUT2) - mcr |= UART_MCR_OUT2; - if (mctrl & TIOCM_LOOP) - mcr |= UART_MCR_LOOP; - - mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; - - serial_port_out(port, UART_MCR, mcr); -} -EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl); - -static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - if (port->set_mctrl) - return port->set_mctrl(port, mctrl); - return serial8250_do_set_mctrl(port, mctrl); -} - -static void serial8250_break_ctl(struct uart_port *port, int break_state) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned long flags; - - serial8250_rpm_get(up); - spin_lock_irqsave(&port->lock, flags); - if (break_state == -1) - up->lcr |= UART_LCR_SBC; - else - up->lcr &= ~UART_LCR_SBC; - serial_port_out(port, UART_LCR, up->lcr); - spin_unlock_irqrestore(&port->lock, flags); - serial8250_rpm_put(up); -} - -/* - * Wait for transmitter & holding register to empty - */ -static void wait_for_xmitr(struct uart_8250_port *up, int bits) -{ - unsigned int status, tmout = 10000; - - /* Wait up to 10ms for the character(s) to be sent. */ - for (;;) { - status = serial_in(up, UART_LSR); - - up->lsr_saved_flags |= status & LSR_SAVE_FLAGS; - - if ((status & bits) == bits) - break; - if (--tmout == 0) - break; - udelay(1); - } - - /* Wait up to 1s for flow control if necessary */ - if (up->port.flags & UPF_CONS_FLOW) { - unsigned int tmout; - for (tmout = 1000000; tmout; tmout--) { - unsigned int msr = serial_in(up, UART_MSR); - up->msr_saved_flags |= msr & MSR_SAVE_FLAGS; - if (msr & UART_MSR_CTS) - break; - udelay(1); - touch_nmi_watchdog(); - } - } -} - -#ifdef CONFIG_CONSOLE_POLL -/* - * Console polling routines for writing and reading from the uart while - * in an interrupt or debug context. - */ - -static int serial8250_get_poll_char(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned char lsr; - int status; - - serial8250_rpm_get(up); - - lsr = serial_port_in(port, UART_LSR); - - if (!(lsr & UART_LSR_DR)) { - status = NO_POLL_CHAR; - goto out; - } - - status = serial_port_in(port, UART_RX); -out: - serial8250_rpm_put(up); - return status; -} - - -static void serial8250_put_poll_char(struct uart_port *port, - unsigned char c) -{ - unsigned int ier; - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_rpm_get(up); - /* - * First save the IER then disable the interrupts - */ - ier = serial_port_in(port, UART_IER); - if (up->capabilities & UART_CAP_UUE) - serial_port_out(port, UART_IER, UART_IER_UUE); - else - serial_port_out(port, UART_IER, 0); - - wait_for_xmitr(up, BOTH_EMPTY); - /* - * Send the character out. - */ - serial_port_out(port, UART_TX, c); - - /* - * Finally, wait for transmitter to become empty - * and restore the IER - */ - wait_for_xmitr(up, BOTH_EMPTY); - serial_port_out(port, UART_IER, ier); - serial8250_rpm_put(up); -} - -#endif /* CONFIG_CONSOLE_POLL */ - -int serial8250_do_startup(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned long flags; - unsigned char lsr, iir; - int retval; - - if (port->type == PORT_8250_CIR) - return -ENODEV; - - if (!port->fifosize) - port->fifosize = uart_config[port->type].fifo_size; - if (!up->tx_loadsz) - up->tx_loadsz = uart_config[port->type].tx_loadsz; - if (!up->capabilities) - up->capabilities = uart_config[port->type].flags; - up->mcr = 0; - - if (port->iotype != up->cur_iotype) - set_io_from_upio(port); - - serial8250_rpm_get(up); - if (port->type == PORT_16C950) { - /* Wake up and initialize UART */ - up->acr = 0; - serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); - serial_port_out(port, UART_EFR, UART_EFR_ECB); - serial_port_out(port, UART_IER, 0); - serial_port_out(port, UART_LCR, 0); - serial_icr_write(up, UART_CSR, 0); /* Reset the UART */ - serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); - serial_port_out(port, UART_EFR, UART_EFR_ECB); - serial_port_out(port, UART_LCR, 0); - } - -#ifdef CONFIG_SERIAL_8250_RSA - /* - * If this is an RSA port, see if we can kick it up to the - * higher speed clock. - */ - enable_rsa(up); -#endif - /* - * Clear the FIFO buffers and disable them. - * (they will be reenabled in set_termios()) - */ - serial8250_clear_fifos(up); - - /* - * Clear the interrupt registers. - */ - serial_port_in(port, UART_LSR); - serial_port_in(port, UART_RX); - serial_port_in(port, UART_IIR); - serial_port_in(port, UART_MSR); - - /* - * At this point, there's no way the LSR could still be 0xff; - * if it is, then bail out, because there's likely no UART - * here. - */ - if (!(port->flags & UPF_BUGGY_UART) && - (serial_port_in(port, UART_LSR) == 0xff)) { - printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n", - serial_index(port)); - retval = -ENODEV; - goto out; - } - - /* - * For a XR16C850, we need to set the trigger levels - */ - if (port->type == PORT_16850) { - unsigned char fctr; - - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - - fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX); - serial_port_out(port, UART_FCTR, - fctr | UART_FCTR_TRGD | UART_FCTR_RX); - serial_port_out(port, UART_TRG, UART_TRG_96); - serial_port_out(port, UART_FCTR, - fctr | UART_FCTR_TRGD | UART_FCTR_TX); - serial_port_out(port, UART_TRG, UART_TRG_96); - - serial_port_out(port, UART_LCR, 0); - } - - if (port->irq) { - unsigned char iir1; - /* - * Test for UARTs that do not reassert THRE when the - * transmitter is idle and the interrupt has already - * been cleared. Real 16550s should always reassert - * this interrupt whenever the transmitter is idle and - * the interrupt is enabled. Delays are necessary to - * allow register changes to become visible. - */ - spin_lock_irqsave(&port->lock, flags); - if (up->port.irqflags & IRQF_SHARED) - disable_irq_nosync(port->irq); - - wait_for_xmitr(up, UART_LSR_THRE); - serial_port_out_sync(port, UART_IER, UART_IER_THRI); - udelay(1); /* allow THRE to set */ - iir1 = serial_port_in(port, UART_IIR); - serial_port_out(port, UART_IER, 0); - serial_port_out_sync(port, UART_IER, UART_IER_THRI); - udelay(1); /* allow a working UART time to re-assert THRE */ - iir = serial_port_in(port, UART_IIR); - serial_port_out(port, UART_IER, 0); - - if (port->irqflags & IRQF_SHARED) - enable_irq(port->irq); - spin_unlock_irqrestore(&port->lock, flags); - - /* - * If the interrupt is not reasserted, or we otherwise - * don't trust the iir, setup a timer to kick the UART - * on a regular basis. - */ - if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) || - up->port.flags & UPF_BUG_THRE) { - up->bugs |= UART_BUG_THRE; - } - } - - retval = up->ops->setup_irq(up); - if (retval) - goto out; - - /* - * Now, initialize the UART - */ - serial_port_out(port, UART_LCR, UART_LCR_WLEN8); - - spin_lock_irqsave(&port->lock, flags); - if (up->port.flags & UPF_FOURPORT) { - if (!up->port.irq) - up->port.mctrl |= TIOCM_OUT1; - } else - /* - * Most PC uarts need OUT2 raised to enable interrupts. - */ - if (port->irq) - up->port.mctrl |= TIOCM_OUT2; - - serial8250_set_mctrl(port, port->mctrl); - - /* Serial over Lan (SoL) hack: - Intel 8257x Gigabit ethernet chips have a - 16550 emulation, to be used for Serial Over Lan. - Those chips take a longer time than a normal - serial device to signalize that a transmission - data was queued. Due to that, the above test generally - fails. One solution would be to delay the reading of - iir. However, this is not reliable, since the timeout - is variable. So, let's just don't test if we receive - TX irq. This way, we'll never enable UART_BUG_TXEN. - */ - if (up->port.flags & UPF_NO_TXEN_TEST) - goto dont_test_tx_en; - - /* - * Do a quick test to see if we receive an - * interrupt when we enable the TX irq. - */ - serial_port_out(port, UART_IER, UART_IER_THRI); - lsr = serial_port_in(port, UART_LSR); - iir = serial_port_in(port, UART_IIR); - serial_port_out(port, UART_IER, 0); - - if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { - if (!(up->bugs & UART_BUG_TXEN)) { - up->bugs |= UART_BUG_TXEN; - pr_debug("ttyS%d - enabling bad tx status workarounds\n", - serial_index(port)); - } - } else { - up->bugs &= ~UART_BUG_TXEN; - } - -dont_test_tx_en: - spin_unlock_irqrestore(&port->lock, flags); - - /* - * Clear the interrupt registers again for luck, and clear the - * saved flags to avoid getting false values from polling - * routines or the previous session. - */ - serial_port_in(port, UART_LSR); - serial_port_in(port, UART_RX); - serial_port_in(port, UART_IIR); - serial_port_in(port, UART_MSR); - up->lsr_saved_flags = 0; - up->msr_saved_flags = 0; - - /* - * Request DMA channels for both RX and TX. - */ - if (up->dma) { - retval = serial8250_request_dma(up); - if (retval) { - pr_warn_ratelimited("ttyS%d - failed to request DMA\n", - serial_index(port)); - up->dma = NULL; - } - } - - /* - * Finally, enable interrupts. Note: Modem status interrupts - * are set via set_termios(), which will be occurring imminently - * anyway, so we don't enable them here. - */ - up->ier = UART_IER_RLSI | UART_IER_RDI; - serial_port_out(port, UART_IER, up->ier); - - if (port->flags & UPF_FOURPORT) { - unsigned int icp; - /* - * Enable interrupts on the AST Fourport board - */ - icp = (port->iobase & 0xfe0) | 0x01f; - outb_p(0x80, icp); - inb_p(icp); - } - retval = 0; -out: - serial8250_rpm_put(up); - return retval; -} -EXPORT_SYMBOL_GPL(serial8250_do_startup); - -static int serial8250_startup(struct uart_port *port) -{ - if (port->startup) - return port->startup(port); - return serial8250_do_startup(port); -} - -void serial8250_do_shutdown(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned long flags; - - serial8250_rpm_get(up); - /* - * Disable interrupts from this port - */ - up->ier = 0; - serial_port_out(port, UART_IER, 0); - - if (up->dma) - serial8250_release_dma(up); - - spin_lock_irqsave(&port->lock, flags); - if (port->flags & UPF_FOURPORT) { - /* reset interrupts on the AST Fourport board */ - inb((port->iobase & 0xfe0) | 0x1f); - port->mctrl |= TIOCM_OUT1; - } else - port->mctrl &= ~TIOCM_OUT2; - - serial8250_set_mctrl(port, port->mctrl); - spin_unlock_irqrestore(&port->lock, flags); - - /* - * Disable break condition and FIFOs - */ - serial_port_out(port, UART_LCR, - serial_port_in(port, UART_LCR) & ~UART_LCR_SBC); - serial8250_clear_fifos(up); - -#ifdef CONFIG_SERIAL_8250_RSA - /* - * Reset the RSA board back to 115kbps compat mode. - */ - disable_rsa(up); -#endif - - /* - * Read data port to reset things, and then unlink from - * the IRQ chain. - */ - serial_port_in(port, UART_RX); - serial8250_rpm_put(up); - - up->ops->release_irq(up); -} -EXPORT_SYMBOL_GPL(serial8250_do_shutdown); - -static void serial8250_shutdown(struct uart_port *port) -{ - if (port->shutdown) - port->shutdown(port); - else - serial8250_do_shutdown(port); -} - -/* - * XR17V35x UARTs have an extra fractional divisor register (DLD) - * Calculate divisor with extra 4-bit fractional portion - */ -static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up, - unsigned int baud, - unsigned int *frac) -{ - struct uart_port *port = &up->port; - unsigned int quot_16; - - quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud); - *frac = quot_16 & 0x0f; - - return quot_16 >> 4; -} - -static unsigned int serial8250_get_divisor(struct uart_8250_port *up, - unsigned int baud, - unsigned int *frac) -{ - struct uart_port *port = &up->port; - unsigned int quot; - - /* - * Handle magic divisors for baud rates above baud_base on - * SMSC SuperIO chips. - * - */ - if ((port->flags & UPF_MAGIC_MULTIPLIER) && - baud == (port->uartclk/4)) - quot = 0x8001; - else if ((port->flags & UPF_MAGIC_MULTIPLIER) && - baud == (port->uartclk/8)) - quot = 0x8002; - else if (up->port.type == PORT_XR17V35X) - quot = xr17v35x_get_divisor(up, baud, frac); - else - quot = uart_get_divisor(port, baud); - - /* - * Oxford Semi 952 rev B workaround - */ - if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0) - quot++; - - return quot; -} - -static unsigned char serial8250_compute_lcr(struct uart_8250_port *up, - tcflag_t c_cflag) -{ - unsigned char cval; - - switch (c_cflag & CSIZE) { - case CS5: - cval = UART_LCR_WLEN5; - break; - case CS6: - cval = UART_LCR_WLEN6; - break; - case CS7: - cval = UART_LCR_WLEN7; - break; - default: - case CS8: - cval = UART_LCR_WLEN8; - break; - } - - if (c_cflag & CSTOPB) - cval |= UART_LCR_STOP; - if (c_cflag & PARENB) { - cval |= UART_LCR_PARITY; - if (up->bugs & UART_BUG_PARITY) - up->fifo_bug = true; - } - if (!(c_cflag & PARODD)) - cval |= UART_LCR_EPAR; -#ifdef CMSPAR - if (c_cflag & CMSPAR) - cval |= UART_LCR_SPAR; -#endif - - return cval; -} - -static void serial8250_set_divisor(struct uart_port *port, unsigned int baud, - unsigned int quot, unsigned int quot_frac) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - /* Workaround to enable 115200 baud on OMAP1510 internal ports */ - if (is_omap1510_8250(up)) { - if (baud == 115200) { - quot = 1; - serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1); - } else - serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0); - } - - /* - * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2, - * otherwise just set DLAB - */ - if (up->capabilities & UART_NATSEMI) - serial_port_out(port, UART_LCR, 0xe0); - else - serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB); - - serial_dl_write(up, quot); - - /* XR17V35x UARTs have an extra fractional divisor register (DLD) */ - if (up->port.type == PORT_XR17V35X) - serial_port_out(port, 0x2, quot_frac); -} - -void -serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned char cval; - unsigned long flags; - unsigned int baud, quot, frac = 0; - - cval = serial8250_compute_lcr(up, termios->c_cflag); - - /* - * Ask the core to calculate the divisor for us. - */ - baud = uart_get_baud_rate(port, termios, old, - port->uartclk / 16 / 0xffff, - port->uartclk / 16); - quot = serial8250_get_divisor(up, baud, &frac); - - /* - * Ok, we're now changing the port state. Do it with - * interrupts disabled. - */ - serial8250_rpm_get(up); - spin_lock_irqsave(&port->lock, flags); - - up->lcr = cval; /* Save computed LCR */ - - if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) { - /* NOTE: If fifo_bug is not set, a user can set RX_trigger. */ - if ((baud < 2400 && !up->dma) || up->fifo_bug) { - up->fcr &= ~UART_FCR_TRIGGER_MASK; - up->fcr |= UART_FCR_TRIGGER_1; - } - } - - /* - * MCR-based auto flow control. When AFE is enabled, RTS will be - * deasserted when the receive FIFO contains more characters than - * the trigger, or the MCR RTS bit is cleared. In the case where - * the remote UART is not using CTS auto flow control, we must - * have sufficient FIFO entries for the latency of the remote - * UART to respond. IOW, at least 32 bytes of FIFO. - */ - if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) { - up->mcr &= ~UART_MCR_AFE; - if (termios->c_cflag & CRTSCTS) - up->mcr |= UART_MCR_AFE; - } - - /* - * Update the per-port timeout. - */ - uart_update_timeout(port, termios->c_cflag, baud); - - port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; - if (termios->c_iflag & INPCK) - port->read_status_mask |= UART_LSR_FE | UART_LSR_PE; - if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) - port->read_status_mask |= UART_LSR_BI; - - /* - * Characteres to ignore - */ - port->ignore_status_mask = 0; - if (termios->c_iflag & IGNPAR) - port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; - if (termios->c_iflag & IGNBRK) { - port->ignore_status_mask |= UART_LSR_BI; - /* - * If we're ignoring parity and break indicators, - * ignore overruns too (for real raw support). - */ - if (termios->c_iflag & IGNPAR) - port->ignore_status_mask |= UART_LSR_OE; - } - - /* - * ignore all characters if CREAD is not set - */ - if ((termios->c_cflag & CREAD) == 0) - port->ignore_status_mask |= UART_LSR_DR; - - /* - * CTS flow control flag and modem status interrupts - */ - up->ier &= ~UART_IER_MSI; - if (!(up->bugs & UART_BUG_NOMSR) && - UART_ENABLE_MS(&up->port, termios->c_cflag)) - up->ier |= UART_IER_MSI; - if (up->capabilities & UART_CAP_UUE) - up->ier |= UART_IER_UUE; - if (up->capabilities & UART_CAP_RTOIE) - up->ier |= UART_IER_RTOIE; - - serial_port_out(port, UART_IER, up->ier); - - if (up->capabilities & UART_CAP_EFR) { - unsigned char efr = 0; - /* - * TI16C752/Startech hardware flow control. FIXME: - * - TI16C752 requires control thresholds to be set. - * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled. - */ - if (termios->c_cflag & CRTSCTS) - efr |= UART_EFR_CTS; - - serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); - if (port->flags & UPF_EXAR_EFR) - serial_port_out(port, UART_XR_EFR, efr); - else - serial_port_out(port, UART_EFR, efr); - } - - serial8250_set_divisor(port, baud, quot, frac); - - /* - * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR - * is written without DLAB set, this mode will be disabled. - */ - if (port->type == PORT_16750) - serial_port_out(port, UART_FCR, up->fcr); - - serial_port_out(port, UART_LCR, up->lcr); /* reset DLAB */ - if (port->type != PORT_16750) { - /* emulated UARTs (Lucent Venus 167x) need two steps */ - if (up->fcr & UART_FCR_ENABLE_FIFO) - serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO); - serial_port_out(port, UART_FCR, up->fcr); /* set fcr */ - } - serial8250_set_mctrl(port, port->mctrl); - spin_unlock_irqrestore(&port->lock, flags); - serial8250_rpm_put(up); - - /* Don't rewrite B0 */ - if (tty_termios_baud_rate(termios)) - tty_termios_encode_baud_rate(termios, baud, baud); -} -EXPORT_SYMBOL(serial8250_do_set_termios); - -static void -serial8250_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) -{ - if (port->set_termios) - port->set_termios(port, termios, old); - else - serial8250_do_set_termios(port, termios, old); -} - -static void -serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios) -{ - if (termios->c_line == N_PPS) { - port->flags |= UPF_HARDPPS_CD; - spin_lock_irq(&port->lock); - serial8250_enable_ms(port); - spin_unlock_irq(&port->lock); - } else { - port->flags &= ~UPF_HARDPPS_CD; - if (!UART_ENABLE_MS(port, termios->c_cflag)) { - spin_lock_irq(&port->lock); - serial8250_disable_ms(port); - spin_unlock_irq(&port->lock); - } - } -} - - -void serial8250_do_pm(struct uart_port *port, unsigned int state, - unsigned int oldstate) -{ - struct uart_8250_port *p = up_to_u8250p(port); - - serial8250_set_sleep(p, state != 0); -} -EXPORT_SYMBOL(serial8250_do_pm); - -static void -serial8250_pm(struct uart_port *port, unsigned int state, - unsigned int oldstate) -{ - if (port->pm) - port->pm(port, state, oldstate); - else - serial8250_do_pm(port, state, oldstate); -} - -static unsigned int serial8250_port_size(struct uart_8250_port *pt) -{ - if (pt->port.mapsize) - return pt->port.mapsize; - if (pt->port.iotype == UPIO_AU) { - if (pt->port.type == PORT_RT2880) - return 0x100; - return 0x1000; - } - if (is_omap1_8250(pt)) - return 0x16 << pt->port.regshift; - - return 8 << pt->port.regshift; -} - -/* - * Resource handling. - */ -static int serial8250_request_std_resource(struct uart_8250_port *up) -{ - unsigned int size = serial8250_port_size(up); - struct uart_port *port = &up->port; - int ret = 0; - - switch (port->iotype) { - case UPIO_AU: - case UPIO_TSI: - case UPIO_MEM32: - case UPIO_MEM32BE: - case UPIO_MEM: - if (!port->mapbase) - break; - - if (!request_mem_region(port->mapbase, size, "serial")) { - ret = -EBUSY; - break; - } - - if (port->flags & UPF_IOREMAP) { - port->membase = ioremap_nocache(port->mapbase, size); - if (!port->membase) { - release_mem_region(port->mapbase, size); - ret = -ENOMEM; - } - } - break; - - case UPIO_HUB6: - case UPIO_PORT: - if (!request_region(port->iobase, size, "serial")) - ret = -EBUSY; - break; - } - return ret; -} - -static void serial8250_release_std_resource(struct uart_8250_port *up) -{ - unsigned int size = serial8250_port_size(up); - struct uart_port *port = &up->port; - - switch (port->iotype) { - case UPIO_AU: - case UPIO_TSI: - case UPIO_MEM32: - case UPIO_MEM32BE: - case UPIO_MEM: - if (!port->mapbase) - break; - - if (port->flags & UPF_IOREMAP) { - iounmap(port->membase); - port->membase = NULL; - } - - release_mem_region(port->mapbase, size); - break; - - case UPIO_HUB6: - case UPIO_PORT: - release_region(port->iobase, size); - break; - } -} - #ifdef CONFIG_SERIAL_8250_RSA static int serial8250_request_rsa_resource(struct uart_8250_port *up) { @@ -2870,259 +405,6 @@ static void serial8250_release_rsa_resource(struct uart_8250_port *up) } #endif -static void serial8250_release_port(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_release_std_resource(up); -} - -static int serial8250_request_port(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - int ret; - - if (port->type == PORT_8250_CIR) - return -ENODEV; - - ret = serial8250_request_std_resource(up); - - return ret; -} - -static int fcr_get_rxtrig_bytes(struct uart_8250_port *up) -{ - const struct serial8250_config *conf_type = &uart_config[up->port.type]; - unsigned char bytes; - - bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)]; - - return bytes ? bytes : -EOPNOTSUPP; -} - -static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes) -{ - const struct serial8250_config *conf_type = &uart_config[up->port.type]; - int i; - - if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)]) - return -EOPNOTSUPP; - - for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) { - if (bytes < conf_type->rxtrig_bytes[i]) - /* Use the nearest lower value */ - return (--i) << UART_FCR_R_TRIG_SHIFT; - } - - return UART_FCR_R_TRIG_11; -} - -static int do_get_rxtrig(struct tty_port *port) -{ - struct uart_state *state = container_of(port, struct uart_state, port); - struct uart_port *uport = state->uart_port; - struct uart_8250_port *up = - container_of(uport, struct uart_8250_port, port); - - if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1) - return -EINVAL; - - return fcr_get_rxtrig_bytes(up); -} - -static int do_serial8250_get_rxtrig(struct tty_port *port) -{ - int rxtrig_bytes; - - mutex_lock(&port->mutex); - rxtrig_bytes = do_get_rxtrig(port); - mutex_unlock(&port->mutex); - - return rxtrig_bytes; -} - -static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev, - struct device_attribute *attr, char *buf) -{ - struct tty_port *port = dev_get_drvdata(dev); - int rxtrig_bytes; - - rxtrig_bytes = do_serial8250_get_rxtrig(port); - if (rxtrig_bytes < 0) - return rxtrig_bytes; - - return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes); -} - -static int do_set_rxtrig(struct tty_port *port, unsigned char bytes) -{ - struct uart_state *state = container_of(port, struct uart_state, port); - struct uart_port *uport = state->uart_port; - struct uart_8250_port *up = - container_of(uport, struct uart_8250_port, port); - int rxtrig; - - if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 || - up->fifo_bug) - return -EINVAL; - - rxtrig = bytes_to_fcr_rxtrig(up, bytes); - if (rxtrig < 0) - return rxtrig; - - serial8250_clear_fifos(up); - up->fcr &= ~UART_FCR_TRIGGER_MASK; - up->fcr |= (unsigned char)rxtrig; - serial_out(up, UART_FCR, up->fcr); - return 0; -} - -static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes) -{ - int ret; - - mutex_lock(&port->mutex); - ret = do_set_rxtrig(port, bytes); - mutex_unlock(&port->mutex); - - return ret; -} - -static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev, - struct device_attribute *attr, const char *buf, size_t count) -{ - struct tty_port *port = dev_get_drvdata(dev); - unsigned char bytes; - int ret; - - if (!count) - return -EINVAL; - - ret = kstrtou8(buf, 10, &bytes); - if (ret < 0) - return ret; - - ret = do_serial8250_set_rxtrig(port, bytes); - if (ret < 0) - return ret; - - return count; -} - -static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP, - serial8250_get_attr_rx_trig_bytes, - serial8250_set_attr_rx_trig_bytes); - -static struct attribute *serial8250_dev_attrs[] = { - &dev_attr_rx_trig_bytes.attr, - NULL, - }; - -static struct attribute_group serial8250_dev_attr_group = { - .attrs = serial8250_dev_attrs, - }; - -static void register_dev_spec_attr_grp(struct uart_8250_port *up) -{ - const struct serial8250_config *conf_type = &uart_config[up->port.type]; - - if (conf_type->rxtrig_bytes[0]) - up->port.attr_group = &serial8250_dev_attr_group; -} - -static void serial8250_config_port(struct uart_port *port, int flags) -{ - struct uart_8250_port *up = up_to_u8250p(port); - int ret; - - if (port->type == PORT_8250_CIR) - return; - - /* - * Find the region that we can probe for. This in turn - * tells us whether we can probe for the type of port. - */ - ret = serial8250_request_std_resource(up); - if (ret < 0) - return; - - if (port->iotype != up->cur_iotype) - set_io_from_upio(port); - - if (flags & UART_CONFIG_TYPE) - autoconfig(up); - - /* if access method is AU, it is a 16550 with a quirk */ - if (port->type == PORT_16550A && port->iotype == UPIO_AU) - up->bugs |= UART_BUG_NOMSR; - - /* HW bugs may trigger IRQ while IIR == NO_INT */ - if (port->type == PORT_TEGRA) - up->bugs |= UART_BUG_NOMSR; - - if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ) - autoconfig_irq(up); - - if (port->type == PORT_UNKNOWN) - serial8250_release_std_resource(up); - - /* Fixme: probably not the best place for this */ - if ((port->type == PORT_XR17V35X) || - (port->type == PORT_XR17D15X)) - port->handle_irq = exar_handle_irq; - - register_dev_spec_attr_grp(up); - up->fcr = uart_config[up->port.type].fcr; -} - -static int -serial8250_verify_port(struct uart_port *port, struct serial_struct *ser) -{ - if (ser->irq >= nr_irqs || ser->irq < 0 || - ser->baud_base < 9600 || ser->type < PORT_UNKNOWN || - ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS || - ser->type == PORT_STARTECH) - return -EINVAL; - return 0; -} - -static const char * -serial8250_type(struct uart_port *port) -{ - int type = port->type; - - if (type >= ARRAY_SIZE(uart_config)) - type = 0; - return uart_config[type].name; -} - -static const struct uart_ops serial8250_pops = { - .tx_empty = serial8250_tx_empty, - .set_mctrl = serial8250_set_mctrl, - .get_mctrl = serial8250_get_mctrl, - .stop_tx = serial8250_stop_tx, - .start_tx = serial8250_start_tx, - .throttle = serial8250_throttle, - .unthrottle = serial8250_unthrottle, - .stop_rx = serial8250_stop_rx, - .enable_ms = serial8250_enable_ms, - .break_ctl = serial8250_break_ctl, - .startup = serial8250_startup, - .shutdown = serial8250_shutdown, - .set_termios = serial8250_set_termios, - .set_ldisc = serial8250_set_ldisc, - .pm = serial8250_pm, - .type = serial8250_type, - .release_port = serial8250_release_port, - .request_port = serial8250_request_port, - .config_port = serial8250_config_port, - .verify_port = serial8250_verify_port, -#ifdef CONFIG_CONSOLE_POLL - .poll_get_char = serial8250_get_poll_char, - .poll_put_char = serial8250_put_poll_char, -#endif -}; - static const struct uart_ops *base_ops; static struct uart_ops univ8250_port_ops; @@ -3161,42 +443,6 @@ void serial8250_set_isa_configurator( } EXPORT_SYMBOL(serial8250_set_isa_configurator); -static void serial8250_init_port(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - - spin_lock_init(&port->lock); - port->ops = &serial8250_pops; - - up->cur_iotype = 0xFF; -} - -static void serial8250_set_defaults(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - - if (up->port.flags & UPF_FIXED_TYPE) { - unsigned int type = up->port.type; - - if (!up->port.fifosize) - up->port.fifosize = uart_config[type].fifo_size; - if (!up->tx_loadsz) - up->tx_loadsz = uart_config[type].tx_loadsz; - if (!up->capabilities) - up->capabilities = uart_config[type].flags; - } - - set_io_from_upio(port); - - /* default dma handlers */ - if (up->dma) { - if (!up->dma->tx_dma) - up->dma->tx_dma = serial8250_tx_dma; - if (!up->dma->rx_dma) - up->dma->rx_dma = serial8250_rx_dma; - } -} - #ifdef CONFIG_SERIAL_8250_RSA static void univ8250_config_port(struct uart_port *port, int flags) @@ -3332,6 +578,9 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev) for (i = 0; i < nr_uarts; i++) { struct uart_8250_port *up = &serial8250_ports[i]; + if (up->port.type == PORT_8250_CIR) + continue; + if (up->port.dev) continue; @@ -3346,94 +595,6 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev) #ifdef CONFIG_SERIAL_8250_CONSOLE -static void serial8250_console_putchar(struct uart_port *port, int ch) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - wait_for_xmitr(up, UART_LSR_THRE); - serial_port_out(port, UART_TX, ch); -} - -/* - * Print a string to the serial port trying not to disturb - * any possible real use of the port... - * - * The console_lock must be held when we get here. - */ -static void serial8250_console_write(struct uart_8250_port *up, const char *s, - unsigned int count) -{ - struct uart_port *port = &up->port; - unsigned long flags; - unsigned int ier; - int locked = 1; - - touch_nmi_watchdog(); - - serial8250_rpm_get(up); - - if (port->sysrq) - locked = 0; - else if (oops_in_progress || in_kdb_printk()) - locked = spin_trylock_irqsave(&port->lock, flags); - else - spin_lock_irqsave(&port->lock, flags); - - /* - * First save the IER then disable the interrupts - */ - ier = serial_port_in(port, UART_IER); - - if (up->capabilities & UART_CAP_UUE) - serial_port_out(port, UART_IER, UART_IER_UUE); - else - serial_port_out(port, UART_IER, 0); - - /* check scratch reg to see if port powered off during system sleep */ - if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) { - struct ktermios termios; - unsigned int baud, quot, frac = 0; - - termios.c_cflag = port->cons->cflag; - if (port->state->port.tty && termios.c_cflag == 0) - termios.c_cflag = port->state->port.tty->termios.c_cflag; - - baud = uart_get_baud_rate(port, &termios, NULL, - port->uartclk / 16 / 0xffff, - port->uartclk / 16); - quot = serial8250_get_divisor(up, baud, &frac); - - serial8250_set_divisor(port, baud, quot, frac); - serial_port_out(port, UART_LCR, up->lcr); - serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS); - - up->canary = 0; - } - - uart_console_write(port, s, count, serial8250_console_putchar); - - /* - * Finally, wait for transmitter to become empty - * and restore the IER - */ - wait_for_xmitr(up, BOTH_EMPTY); - serial_port_out(port, UART_IER, ier); - - /* - * The receive handling will happen properly because the - * receive ready bit will still be set; it is not cleared - * on read. However, modem control will not, we must - * call it if we have saved something in the saved flags - * while processing with interrupts off. - */ - if (up->msr_saved_flags) - serial8250_modem_status(up); - - if (locked) - spin_unlock_irqrestore(&port->lock, flags); - serial8250_rpm_put(up); -} - static void univ8250_console_write(struct console *co, const char *s, unsigned int count) { @@ -3442,39 +603,6 @@ static void univ8250_console_write(struct console *co, const char *s, serial8250_console_write(up, s, count); } -static unsigned int probe_baud(struct uart_port *port) -{ - unsigned char lcr, dll, dlm; - unsigned int quot; - - lcr = serial_port_in(port, UART_LCR); - serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB); - dll = serial_port_in(port, UART_DLL); - dlm = serial_port_in(port, UART_DLM); - serial_port_out(port, UART_LCR, lcr); - - quot = (dlm << 8) | dll; - return (port->uartclk / 16) / quot; -} - -static int serial8250_console_setup(struct uart_port *port, char *options, bool probe) -{ - int baud = 9600; - int bits = 8; - int parity = 'n'; - int flow = 'n'; - - if (!port->iobase && !port->membase) - return -ENODEV; - - if (options) - uart_parse_options(options, &baud, &parity, &bits, &flow); - else if (probe) - baud = probe_baud(port); - - return uart_set_options(port, port->cons, baud, parity, bits, flow); -} - static int univ8250_console_setup(struct console *co, char *options) { struct uart_port *port; @@ -3558,6 +686,9 @@ static struct console univ8250_console = { static int __init univ8250_console_init(void) { + if (nr_uarts == 0) + return -ENODEV; + serial8250_isa_init_ports(); register_console(&univ8250_console); return 0; @@ -3588,7 +719,7 @@ int __init early_serial_setup(struct uart_port *port) { struct uart_port *p; - if (port->line >= ARRAY_SIZE(serial8250_ports)) + if (port->line >= ARRAY_SIZE(serial8250_ports) || nr_uarts == 0) return -ENODEV; serial8250_isa_init_ports(); @@ -3860,7 +991,6 @@ int serial8250_register_8250_port(struct uart_8250_port *up) uart->port.mapbase = up->port.mapbase; uart->port.mapsize = up->port.mapsize; uart->port.private_data = up->port.private_data; - uart->port.fifosize = up->port.fifosize; uart->tx_loadsz = up->tx_loadsz; uart->capabilities = up->capabilities; uart->port.throttle = up->port.throttle; @@ -3909,13 +1039,24 @@ int serial8250_register_8250_port(struct uart_8250_port *up) if (up->dl_write) uart->dl_write = up->dl_write; - if (serial8250_isa_config != NULL) - serial8250_isa_config(0, &uart->port, - &uart->capabilities); + if (uart->port.type != PORT_8250_CIR) { + if (serial8250_isa_config != NULL) + serial8250_isa_config(0, &uart->port, + &uart->capabilities); + + ret = uart_add_one_port(&serial8250_reg, + &uart->port); + if (ret == 0) + ret = uart->port.line; + } else { + dev_info(uart->port.dev, + "skipping CIR port at 0x%lx / 0x%llx, IRQ %d\n", + uart->port.iobase, + (unsigned long long)uart->port.mapbase, + uart->port.irq); - ret = uart_add_one_port(&serial8250_reg, &uart->port); - if (ret == 0) - ret = uart->port.line; + ret = 0; + } } mutex_unlock(&serial_mutex); @@ -3955,6 +1096,9 @@ static int __init serial8250_init(void) { int ret; + if (nr_uarts == 0) + return -ENODEV; + serial8250_isa_init_ports(); printk(KERN_INFO "Serial: 8250/16550 driver, " diff --git a/kernel/drivers/tty/serial/8250/8250_dma.c b/kernel/drivers/tty/serial/8250/8250_dma.c index 21d01a491..78259d3c6 100644 --- a/kernel/drivers/tty/serial/8250/8250_dma.c +++ b/kernel/drivers/tty/serial/8250/8250_dma.c @@ -54,9 +54,6 @@ static void __dma_rx_complete(void *param) struct dma_tx_state state; int count; - dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr, - dma->rx_size, DMA_FROM_DEVICE); - dma->rx_running = 0; dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state); @@ -80,10 +77,6 @@ int serial8250_tx_dma(struct uart_8250_port *p) return 0; dma->tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); - if (dma->tx_size < p->port.fifosize) { - ret = -EINVAL; - goto err; - } desc = dmaengine_prep_slave_single(dma->txchan, dma->tx_addr + xmit->tail, @@ -156,9 +149,6 @@ int serial8250_rx_dma(struct uart_8250_port *p, unsigned int iir) dma->rx_cookie = dmaengine_submit(desc); - dma_sync_single_for_device(dma->rxchan->device->dev, dma->rx_addr, - dma->rx_size, DMA_FROM_DEVICE); - dma_async_issue_pending(dma->rxchan); return 0; diff --git a/kernel/drivers/tty/serial/8250/8250_dw.c b/kernel/drivers/tty/serial/8250/8250_dw.c index 176f18f2e..a5d319e4a 100644 --- a/kernel/drivers/tty/serial/8250/8250_dw.c +++ b/kernel/drivers/tty/serial/8250/8250_dw.c @@ -56,7 +56,6 @@ struct dw8250_data { u8 usr_reg; - int last_mcr; int line; int msr_mask_on; int msr_mask_off; @@ -64,6 +63,9 @@ struct dw8250_data { struct clk *pclk; struct reset_control *rst; struct uart_8250_dma dma; + + unsigned int skip_autocfg:1; + unsigned int uart_16550_compatible:1; }; #define BYT_PRV_CLK 0x800 @@ -76,12 +78,6 @@ static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value) { struct dw8250_data *d = p->private_data; - /* If reading MSR, report CTS asserted when auto-CTS/RTS enabled */ - if (offset == UART_MSR && d->last_mcr & UART_MCR_AFE) { - value |= UART_MSR_CTS; - value &= ~UART_MSR_DCTS; - } - /* Override any modem control signals if needed */ if (offset == UART_MSR) { value |= d->msr_mask_on; @@ -101,11 +97,6 @@ static void dw8250_force_idle(struct uart_port *p) static void dw8250_serial_out(struct uart_port *p, int offset, int value) { - struct dw8250_data *d = p->private_data; - - if (offset == UART_MCR) - d->last_mcr = value; - writeb(value, p->membase + (offset << p->regshift)); /* Make sure LCR write wasn't ignored */ @@ -144,11 +135,6 @@ static unsigned int dw8250_serial_inq(struct uart_port *p, int offset) static void dw8250_serial_outq(struct uart_port *p, int offset, int value) { - struct dw8250_data *d = p->private_data; - - if (offset == UART_MCR) - d->last_mcr = value; - value &= 0xff; __raw_writeq(value, p->membase + (offset << p->regshift)); /* Read back to ensure register write ordering. */ @@ -175,11 +161,6 @@ static void dw8250_serial_outq(struct uart_port *p, int offset, int value) static void dw8250_serial_out32(struct uart_port *p, int offset, int value) { - struct dw8250_data *d = p->private_data; - - if (offset == UART_MCR) - d->last_mcr = value; - writel(value, p->membase + (offset << p->regshift)); /* Make sure LCR write wasn't ignored */ @@ -246,10 +227,6 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios, if (IS_ERR(d->clk) || !old) goto out; - /* Not requesting clock rates below 1.8432Mhz */ - if (baud < 115200) - baud = 115200; - clk_disable_unprepare(d->clk); rate = clk_round_rate(d->clk, baud * 16); ret = clk_set_rate(d->clk, rate); @@ -257,28 +234,86 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios, if (!ret) p->uartclk = rate; + + p->status &= ~UPSTAT_AUTOCTS; + if (termios->c_cflag & CRTSCTS) + p->status |= UPSTAT_AUTOCTS; + out: serial8250_do_set_termios(p, termios, old); } -static bool dw8250_dma_filter(struct dma_chan *chan, void *param) +/* + * dw8250_fallback_dma_filter will prevent the UART from getting just any free + * channel on platforms that have DMA engines, but don't have any channels + * assigned to the UART. + * + * REVISIT: This is a work around for limitation in the DMA Engine API. Once the + * core problem is fixed, this function is no longer needed. + */ +static bool dw8250_fallback_dma_filter(struct dma_chan *chan, void *param) { return false; } -static void dw8250_setup_port(struct uart_8250_port *up) +static bool dw8250_idma_filter(struct dma_chan *chan, void *param) { - struct uart_port *p = &up->port; - u32 reg = readl(p->membase + DW_UART_UCV); + return param == chan->device->dev->parent; +} + +static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data) +{ + if (p->dev->of_node) { + struct device_node *np = p->dev->of_node; + int id; + + /* get index of serial line, if found in DT aliases */ + id = of_alias_get_id(np, "serial"); + if (id >= 0) + p->line = id; +#ifdef CONFIG_64BIT + if (of_device_is_compatible(np, "cavium,octeon-3860-uart")) { + p->serial_in = dw8250_serial_inq; + p->serial_out = dw8250_serial_outq; + p->flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE; + p->type = PORT_OCTEON; + data->usr_reg = 0x27; + data->skip_autocfg = true; + } +#endif + } else if (has_acpi_companion(p->dev)) { + p->iotype = UPIO_MEM32; + p->regshift = 2; + p->serial_in = dw8250_serial_in32; + p->set_termios = dw8250_set_termios; + /* So far none of there implement the Busy Functionality */ + data->uart_16550_compatible = true; + } + + /* Platforms with iDMA */ + if (platform_get_resource_byname(to_platform_device(p->dev), + IORESOURCE_MEM, "lpss_priv")) { + p->set_termios = dw8250_set_termios; + data->dma.rx_param = p->dev->parent; + data->dma.tx_param = p->dev->parent; + data->dma.fn = dw8250_idma_filter; + } +} + +static void dw8250_setup_port(struct uart_port *p) +{ + struct uart_8250_port *up = up_to_u8250p(p); + u32 reg; /* * If the Component Version Register returns zero, we know that * ADDITIONAL_FEATURES are not enabled. No need to go any further. */ + reg = readl(p->membase + DW_UART_UCV); if (!reg) return; - dev_dbg_ratelimited(p->dev, "Designware UART version %c.%c%c\n", + dev_dbg(p->dev, "Designware UART version %c.%c%c\n", (reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff); reg = readl(p->membase + DW_UART_CPR); @@ -290,7 +325,6 @@ static void dw8250_setup_port(struct uart_8250_port *up) p->type = PORT_16550A; p->flags |= UPF_FIXED_TYPE; p->fifosize = DW_UART_CPR_FIFO_SIZE(reg); - up->tx_loadsz = p->fifosize; up->capabilities = UART_CAP_FIFO; } @@ -298,149 +332,91 @@ static void dw8250_setup_port(struct uart_8250_port *up) up->capabilities |= UART_CAP_AFE; } -static int dw8250_probe_of(struct uart_port *p, - struct dw8250_data *data) +static int dw8250_probe(struct platform_device *pdev) { - struct device_node *np = p->dev->of_node; - struct uart_8250_port *up = up_to_u8250p(p); - u32 val; - bool has_ucv = true; - int id; + struct uart_8250_port uart = {}; + struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + int irq = platform_get_irq(pdev, 0); + struct uart_port *p = &uart.port; + struct dw8250_data *data; + int err; + u32 val; -#ifdef CONFIG_64BIT - if (of_device_is_compatible(np, "cavium,octeon-3860-uart")) { - p->serial_in = dw8250_serial_inq; - p->serial_out = dw8250_serial_outq; - p->flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE; - p->type = PORT_OCTEON; - data->usr_reg = 0x27; - has_ucv = false; - } else -#endif - if (!of_property_read_u32(np, "reg-io-width", &val)) { - switch (val) { - case 1: - break; - case 4: - p->iotype = UPIO_MEM32; - p->serial_in = dw8250_serial_in32; - p->serial_out = dw8250_serial_out32; - break; - default: - dev_err(p->dev, "unsupported reg-io-width (%u)\n", val); - return -EINVAL; - } + if (!regs) { + dev_err(&pdev->dev, "no registers defined\n"); + return -EINVAL; } - if (has_ucv) - dw8250_setup_port(up); - /* if we have a valid fifosize, try hooking up DMA here */ - if (p->fifosize) { - up->dma = &data->dma; - - up->dma->rxconf.src_maxburst = p->fifosize / 4; - up->dma->txconf.dst_maxburst = p->fifosize / 4; + if (irq < 0) { + if (irq != -EPROBE_DEFER) + dev_err(&pdev->dev, "cannot get irq\n"); + return irq; } - if (!of_property_read_u32(np, "reg-shift", &val)) + spin_lock_init(&p->lock); + p->mapbase = regs->start; + p->irq = irq; + p->handle_irq = dw8250_handle_irq; + p->pm = dw8250_do_pm; + p->type = PORT_8250; + p->flags = UPF_SHARE_IRQ | UPF_FIXED_PORT; + p->dev = &pdev->dev; + p->iotype = UPIO_MEM; + p->serial_in = dw8250_serial_in; + p->serial_out = dw8250_serial_out; + + p->membase = devm_ioremap(&pdev->dev, regs->start, resource_size(regs)); + if (!p->membase) + return -ENOMEM; + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->dma.fn = dw8250_fallback_dma_filter; + data->usr_reg = DW_UART_USR; + p->private_data = data; + + data->uart_16550_compatible = device_property_read_bool(p->dev, + "snps,uart-16550-compatible"); + + err = device_property_read_u32(p->dev, "reg-shift", &val); + if (!err) p->regshift = val; - /* get index of serial line, if found in DT aliases */ - id = of_alias_get_id(np, "serial"); - if (id >= 0) - p->line = id; + err = device_property_read_u32(p->dev, "reg-io-width", &val); + if (!err && val == 4) { + p->iotype = UPIO_MEM32; + p->serial_in = dw8250_serial_in32; + p->serial_out = dw8250_serial_out32; + } - if (of_property_read_bool(np, "dcd-override")) { + if (device_property_read_bool(p->dev, "dcd-override")) { /* Always report DCD as active */ data->msr_mask_on |= UART_MSR_DCD; data->msr_mask_off |= UART_MSR_DDCD; } - if (of_property_read_bool(np, "dsr-override")) { + if (device_property_read_bool(p->dev, "dsr-override")) { /* Always report DSR as active */ data->msr_mask_on |= UART_MSR_DSR; data->msr_mask_off |= UART_MSR_DDSR; } - if (of_property_read_bool(np, "cts-override")) { + if (device_property_read_bool(p->dev, "cts-override")) { /* Always report CTS as active */ data->msr_mask_on |= UART_MSR_CTS; data->msr_mask_off |= UART_MSR_DCTS; } - if (of_property_read_bool(np, "ri-override")) { + if (device_property_read_bool(p->dev, "ri-override")) { /* Always report Ring indicator as inactive */ data->msr_mask_off |= UART_MSR_RI; data->msr_mask_off |= UART_MSR_TERI; } - return 0; -} - -static int dw8250_probe_acpi(struct uart_8250_port *up, - struct dw8250_data *data) -{ - struct uart_port *p = &up->port; - - dw8250_setup_port(up); - - p->iotype = UPIO_MEM32; - p->serial_in = dw8250_serial_in32; - p->serial_out = dw8250_serial_out32; - p->regshift = 2; - - up->dma = &data->dma; - - up->dma->rxconf.src_maxburst = p->fifosize / 4; - up->dma->txconf.dst_maxburst = p->fifosize / 4; - - up->port.set_termios = dw8250_set_termios; - - return 0; -} - -static int dw8250_probe(struct platform_device *pdev) -{ - struct uart_8250_port uart = {}; - struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); - int irq = platform_get_irq(pdev, 0); - struct dw8250_data *data; - int err; - - if (!regs) { - dev_err(&pdev->dev, "no registers defined\n"); - return -EINVAL; - } - - if (irq < 0) { - if (irq != -EPROBE_DEFER) - dev_err(&pdev->dev, "cannot get irq\n"); - return irq; - } - - spin_lock_init(&uart.port.lock); - uart.port.mapbase = regs->start; - uart.port.irq = irq; - uart.port.handle_irq = dw8250_handle_irq; - uart.port.pm = dw8250_do_pm; - uart.port.type = PORT_8250; - uart.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT; - uart.port.dev = &pdev->dev; - - uart.port.membase = devm_ioremap(&pdev->dev, regs->start, - resource_size(regs)); - if (!uart.port.membase) - return -ENOMEM; - - data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); - if (!data) - return -ENOMEM; - - data->usr_reg = DW_UART_USR; - /* Always ask for fixed clock rate from a property. */ - device_property_read_u32(&pdev->dev, "clock-frequency", - &uart.port.uartclk); + device_property_read_u32(p->dev, "clock-frequency", &p->uartclk); /* If there is separate baudclk, get the rate from it. */ data->clk = devm_clk_get(&pdev->dev, "baudclk"); @@ -454,11 +430,11 @@ static int dw8250_probe(struct platform_device *pdev) dev_warn(&pdev->dev, "could not enable optional baudclk: %d\n", err); else - uart.port.uartclk = clk_get_rate(data->clk); + p->uartclk = clk_get_rate(data->clk); } /* If no clock rate is defined, fail. */ - if (!uart.port.uartclk) { + if (!p->uartclk) { dev_err(&pdev->dev, "clock rate not defined\n"); return -EINVAL; } @@ -484,26 +460,22 @@ static int dw8250_probe(struct platform_device *pdev) if (!IS_ERR(data->rst)) reset_control_deassert(data->rst); - data->dma.rx_param = data; - data->dma.tx_param = data; - data->dma.fn = dw8250_dma_filter; + dw8250_quirks(p, data); - uart.port.iotype = UPIO_MEM; - uart.port.serial_in = dw8250_serial_in; - uart.port.serial_out = dw8250_serial_out; - uart.port.private_data = data; + /* If the Busy Functionality is not implemented, don't handle it */ + if (data->uart_16550_compatible) { + p->serial_out = NULL; + p->handle_irq = NULL; + } - if (pdev->dev.of_node) { - err = dw8250_probe_of(&uart.port, data); - if (err) - goto err_reset; - } else if (ACPI_HANDLE(&pdev->dev)) { - err = dw8250_probe_acpi(&uart, data); - if (err) - goto err_reset; - } else { - err = -ENODEV; - goto err_reset; + if (!data->skip_autocfg) + dw8250_setup_port(p); + + /* If we have a valid fifosize, try hooking up DMA */ + if (p->fifosize) { + data->dma.rxconf.src_maxburst = p->fifosize / 4; + data->dma.txconf.dst_maxburst = p->fifosize / 4; + uart.dma = &data->dma; } data->line = serial8250_register_8250_port(&uart); diff --git a/kernel/drivers/tty/serial/8250/8250_early.c b/kernel/drivers/tty/serial/8250/8250_early.c index 6c0fd8b9d..ceb85792a 100644 --- a/kernel/drivers/tty/serial/8250/8250_early.c +++ b/kernel/drivers/tty/serial/8250/8250_early.c @@ -29,13 +29,15 @@ #include <linux/tty.h> #include <linux/init.h> #include <linux/console.h> +#include <linux/of.h> +#include <linux/of_device.h> #include <linux/serial_reg.h> #include <linux/serial.h> #include <linux/serial_8250.h> #include <asm/io.h> #include <asm/serial.h> -unsigned int __weak __init serial8250_early_in(struct uart_port *port, int offset) +static unsigned int __init serial8250_early_in(struct uart_port *port, int offset) { switch (port->iotype) { case UPIO_MEM: @@ -51,7 +53,7 @@ unsigned int __weak __init serial8250_early_in(struct uart_port *port, int offse } } -void __weak __init serial8250_early_out(struct uart_port *port, int offset, int value) +static void __init serial8250_early_out(struct uart_port *port, int offset, int value) { switch (port->iotype) { case UPIO_MEM: @@ -131,7 +133,7 @@ static void __init init_port(struct earlycon_device *device) serial8250_early_out(port, UART_LCR, c & ~UART_LCR_DLAB); } -static int __init early_serial8250_setup(struct earlycon_device *device, +int __init early_serial8250_setup(struct earlycon_device *device, const char *options) { if (!(device->port.membase || device->port.iobase)) @@ -152,3 +154,5 @@ static int __init early_serial8250_setup(struct earlycon_device *device, } EARLYCON_DECLARE(uart8250, early_serial8250_setup); EARLYCON_DECLARE(uart, early_serial8250_setup); +OF_EARLYCON_DECLARE(ns16550, "ns16550", early_serial8250_setup); +OF_EARLYCON_DECLARE(ns16550a, "ns16550a", early_serial8250_setup); diff --git a/kernel/drivers/tty/serial/8250/8250_fintek.c b/kernel/drivers/tty/serial/8250/8250_fintek.c index 5815e81b5..89474399a 100644 --- a/kernel/drivers/tty/serial/8250/8250_fintek.c +++ b/kernel/drivers/tty/serial/8250/8250_fintek.c @@ -17,18 +17,19 @@ #include <linux/serial_core.h> #include "8250.h" -#define ADDR_PORT 0x4E -#define DATA_PORT 0x4F -#define ENTRY_KEY 0x77 +#define ADDR_PORT 0 +#define DATA_PORT 1 #define EXIT_KEY 0xAA #define CHIP_ID1 0x20 -#define CHIP_ID1_VAL 0x02 #define CHIP_ID2 0x21 -#define CHIP_ID2_VAL 0x16 +#define CHIP_ID_0 0x1602 +#define CHIP_ID_1 0x0501 #define VENDOR_ID1 0x23 #define VENDOR_ID1_VAL 0x19 #define VENDOR_ID2 0x24 #define VENDOR_ID2_VAL 0x34 +#define IO_ADDR1 0x61 +#define IO_ADDR2 0x60 #define LDN 0x7 #define RS485 0xF0 @@ -39,51 +40,49 @@ #define DRIVER_NAME "8250_fintek" -static int fintek_8250_enter_key(void){ +struct fintek_8250 { + u16 base_port; + u8 index; + u8 key; + long line; +}; + +static int fintek_8250_enter_key(u16 base_port, u8 key) +{ - if (!request_muxed_region(ADDR_PORT, 2, DRIVER_NAME)) + if (!request_muxed_region(base_port, 2, DRIVER_NAME)) return -EBUSY; - outb(ENTRY_KEY, ADDR_PORT); - outb(ENTRY_KEY, ADDR_PORT); + outb(key, base_port + ADDR_PORT); + outb(key, base_port + ADDR_PORT); return 0; } -static void fintek_8250_exit_key(void){ - - outb(EXIT_KEY, ADDR_PORT); - release_region(ADDR_PORT, 2); -} - -static int fintek_8250_get_index(resource_size_t base_addr) +static void fintek_8250_exit_key(u16 base_port) { - resource_size_t base[] = {0x3f8, 0x2f8, 0x3e8, 0x2e8}; - int i; - - for (i = 0; i < ARRAY_SIZE(base); i++) - if (base_addr == base[i]) - return i; - return -ENODEV; + outb(EXIT_KEY, base_port + ADDR_PORT); + release_region(base_port + ADDR_PORT, 2); } -static int fintek_8250_check_id(void) +static int fintek_8250_check_id(u16 base_port) { + u16 chip; - outb(CHIP_ID1, ADDR_PORT); - if (inb(DATA_PORT) != CHIP_ID1_VAL) + outb(VENDOR_ID1, base_port + ADDR_PORT); + if (inb(base_port + DATA_PORT) != VENDOR_ID1_VAL) return -ENODEV; - outb(CHIP_ID2, ADDR_PORT); - if (inb(DATA_PORT) != CHIP_ID2_VAL) + outb(VENDOR_ID2, base_port + ADDR_PORT); + if (inb(base_port + DATA_PORT) != VENDOR_ID2_VAL) return -ENODEV; - outb(VENDOR_ID1, ADDR_PORT); - if (inb(DATA_PORT) != VENDOR_ID1_VAL) - return -ENODEV; + outb(CHIP_ID1, base_port + ADDR_PORT); + chip = inb(base_port + DATA_PORT); + outb(CHIP_ID2, base_port + ADDR_PORT); + chip |= inb(base_port + DATA_PORT) << 8; - outb(VENDOR_ID2, ADDR_PORT); - if (inb(DATA_PORT) != VENDOR_ID2_VAL) + if (chip != CHIP_ID_0 && chip != CHIP_ID_1) return -ENODEV; return 0; @@ -93,9 +92,9 @@ static int fintek_8250_rs485_config(struct uart_port *port, struct serial_rs485 *rs485) { uint8_t config = 0; - int index = fintek_8250_get_index(port->iobase); + struct fintek_8250 *pdata = port->private_data; - if (index < 0) + if (!pdata) return -EINVAL; if (rs485->flags & SER_RS485_ENABLED) @@ -125,44 +124,84 @@ static int fintek_8250_rs485_config(struct uart_port *port, if (rs485->flags & SER_RS485_RTS_ON_SEND) config |= RTS_INVERT; - if (fintek_8250_enter_key()) + if (fintek_8250_enter_key(pdata->base_port, pdata->key)) return -EBUSY; - outb(LDN, ADDR_PORT); - outb(index, DATA_PORT); - outb(RS485, ADDR_PORT); - outb(config, DATA_PORT); - fintek_8250_exit_key(); + outb(LDN, pdata->base_port + ADDR_PORT); + outb(pdata->index, pdata->base_port + DATA_PORT); + outb(RS485, pdata->base_port + ADDR_PORT); + outb(config, pdata->base_port + DATA_PORT); + fintek_8250_exit_key(pdata->base_port); port->rs485 = *rs485; return 0; } +static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index) +{ + static const u16 addr[] = {0x4e, 0x2e}; + static const u8 keys[] = {0x77, 0xa0, 0x87, 0x67}; + int i, j, k; + + for (i = 0; i < ARRAY_SIZE(addr); i++) { + for (j = 0; j < ARRAY_SIZE(keys); j++) { + + if (fintek_8250_enter_key(addr[i], keys[j])) + continue; + if (fintek_8250_check_id(addr[i])) { + fintek_8250_exit_key(addr[i]); + continue; + } + + for (k = 0; k < 4; k++) { + u16 aux; + + outb(LDN, addr[i] + ADDR_PORT); + outb(k, addr[i] + DATA_PORT); + + outb(IO_ADDR1, addr[i] + ADDR_PORT); + aux = inb(addr[i] + DATA_PORT); + outb(IO_ADDR2, addr[i] + ADDR_PORT); + aux |= inb(addr[i] + DATA_PORT) << 8; + if (aux != io_address) + continue; + + fintek_8250_exit_key(addr[i]); + *key = keys[j]; + *index = k; + return addr[i]; + } + fintek_8250_exit_key(addr[i]); + } + } + + return -ENODEV; +} + static int fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) { - int line; struct uart_8250_port uart; - int ret; + struct fintek_8250 *pdata; + int base_port; + u8 key; + u8 index; if (!pnp_port_valid(dev, 0)) return -ENODEV; - if (fintek_8250_get_index(pnp_port_start(dev, 0)) < 0) + base_port = fintek_8250_base_port(pnp_port_start(dev, 0), &key, &index); + if (base_port < 0) return -ENODEV; - /* Enable configuration registers*/ - if (fintek_8250_enter_key()) - return -EBUSY; + memset(&uart, 0, sizeof(uart)); - /*Check ID*/ - ret = fintek_8250_check_id(); - fintek_8250_exit_key(); - if (ret) - return ret; + pdata = devm_kzalloc(&dev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return -ENOMEM; + uart.port.private_data = pdata; - memset(&uart, 0, sizeof(uart)); if (!pnp_irq_valid(dev, 0)) return -ENODEV; uart.port.irq = pnp_irq(dev, 0); @@ -176,40 +215,43 @@ fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) uart.port.uartclk = 1843200; uart.port.dev = &dev->dev; - line = serial8250_register_8250_port(&uart); - if (line < 0) + pdata->key = key; + pdata->base_port = base_port; + pdata->index = index; + pdata->line = serial8250_register_8250_port(&uart); + if (pdata->line < 0) return -ENODEV; - pnp_set_drvdata(dev, (void *)((long)line + 1)); + pnp_set_drvdata(dev, pdata); return 0; } static void fintek_8250_remove(struct pnp_dev *dev) { - long line = (long)pnp_get_drvdata(dev); + struct fintek_8250 *pdata = pnp_get_drvdata(dev); - if (line) - serial8250_unregister_port(line - 1); + if (pdata) + serial8250_unregister_port(pdata->line); } #ifdef CONFIG_PM static int fintek_8250_suspend(struct pnp_dev *dev, pm_message_t state) { - long line = (long)pnp_get_drvdata(dev); + struct fintek_8250 *pdata = pnp_get_drvdata(dev); - if (!line) + if (!pdata) return -ENODEV; - serial8250_suspend_port(line - 1); + serial8250_suspend_port(pdata->line); return 0; } static int fintek_8250_resume(struct pnp_dev *dev) { - long line = (long)pnp_get_drvdata(dev); + struct fintek_8250 *pdata = pnp_get_drvdata(dev); - if (!line) + if (!pdata) return -ENODEV; - serial8250_resume_port(line - 1); + serial8250_resume_port(pdata->line); return 0; } #else diff --git a/kernel/drivers/tty/serial/8250/8250_fsl.c b/kernel/drivers/tty/serial/8250/8250_fsl.c index c0533a57e..910bfee5a 100644 --- a/kernel/drivers/tty/serial/8250/8250_fsl.c +++ b/kernel/drivers/tty/serial/8250/8250_fsl.c @@ -60,3 +60,4 @@ int fsl8250_handle_irq(struct uart_port *port) spin_unlock_irqrestore(&up->port.lock, flags); return 1; } +EXPORT_SYMBOL_GPL(fsl8250_handle_irq); diff --git a/kernel/drivers/tty/serial/8250/8250_ingenic.c b/kernel/drivers/tty/serial/8250/8250_ingenic.c new file mode 100644 index 000000000..49394b4c5 --- /dev/null +++ b/kernel/drivers/tty/serial/8250/8250_ingenic.c @@ -0,0 +1,345 @@ +/* + * Copyright (C) 2010 Lars-Peter Clausen <lars@metafoo.de> + * Copyright (C) 2015 Imagination Technologies + * + * Ingenic SoC UART support + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/clk.h> +#include <linux/console.h> +#include <linux/io.h> +#include <linux/libfdt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_fdt.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/serial_8250.h> +#include <linux/serial_core.h> +#include <linux/serial_reg.h> + +#include "8250.h" + +/** ingenic_uart_config: SOC specific config data. */ +struct ingenic_uart_config { + int tx_loadsz; + int fifosize; +}; + +struct ingenic_uart_data { + struct clk *clk_module; + struct clk *clk_baud; + int line; +}; + +static const struct of_device_id of_match[]; + +#define UART_FCR_UME BIT(4) + +#define UART_MCR_MDCE BIT(7) +#define UART_MCR_FCM BIT(6) + +static struct earlycon_device *early_device; + +static uint8_t __init early_in(struct uart_port *port, int offset) +{ + return readl(port->membase + (offset << 2)); +} + +static void __init early_out(struct uart_port *port, int offset, uint8_t value) +{ + writel(value, port->membase + (offset << 2)); +} + +static void __init ingenic_early_console_putc(struct uart_port *port, int c) +{ + uint8_t lsr; + + do { + lsr = early_in(port, UART_LSR); + } while ((lsr & UART_LSR_TEMT) == 0); + + early_out(port, UART_TX, c); +} + +static void __init ingenic_early_console_write(struct console *console, + const char *s, unsigned int count) +{ + uart_console_write(&early_device->port, s, count, + ingenic_early_console_putc); +} + +static void __init ingenic_early_console_setup_clock(struct earlycon_device *dev) +{ + void *fdt = initial_boot_params; + const __be32 *prop; + int offset; + + offset = fdt_path_offset(fdt, "/ext"); + if (offset < 0) + return; + + prop = fdt_getprop(fdt, offset, "clock-frequency", NULL); + if (!prop) + return; + + dev->port.uartclk = be32_to_cpup(prop); +} + +static int __init ingenic_early_console_setup(struct earlycon_device *dev, + const char *opt) +{ + struct uart_port *port = &dev->port; + unsigned int baud, divisor; + + if (!dev->port.membase) + return -ENODEV; + + ingenic_early_console_setup_clock(dev); + + baud = dev->baud ?: 115200; + divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * baud); + + early_out(port, UART_IER, 0); + early_out(port, UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8); + early_out(port, UART_DLL, 0); + early_out(port, UART_DLM, 0); + early_out(port, UART_LCR, UART_LCR_WLEN8); + early_out(port, UART_FCR, UART_FCR_UME | UART_FCR_CLEAR_XMIT | + UART_FCR_CLEAR_RCVR | UART_FCR_ENABLE_FIFO); + early_out(port, UART_MCR, UART_MCR_RTS | UART_MCR_DTR); + + early_out(port, UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8); + early_out(port, UART_DLL, divisor & 0xff); + early_out(port, UART_DLM, (divisor >> 8) & 0xff); + early_out(port, UART_LCR, UART_LCR_WLEN8); + + early_device = dev; + dev->con->write = ingenic_early_console_write; + + return 0; +} + +EARLYCON_DECLARE(jz4740_uart, ingenic_early_console_setup); +OF_EARLYCON_DECLARE(jz4740_uart, "ingenic,jz4740-uart", + ingenic_early_console_setup); + +EARLYCON_DECLARE(jz4775_uart, ingenic_early_console_setup); +OF_EARLYCON_DECLARE(jz4775_uart, "ingenic,jz4775-uart", + ingenic_early_console_setup); + +EARLYCON_DECLARE(jz4780_uart, ingenic_early_console_setup); +OF_EARLYCON_DECLARE(jz4780_uart, "ingenic,jz4780-uart", + ingenic_early_console_setup); + +static void ingenic_uart_serial_out(struct uart_port *p, int offset, int value) +{ + int ier; + + switch (offset) { + case UART_FCR: + /* UART module enable */ + value |= UART_FCR_UME; + break; + + case UART_IER: + /* Enable receive timeout interrupt with the + * receive line status interrupt */ + value |= (value & 0x4) << 2; + break; + + case UART_MCR: + /* If we have enabled modem status IRQs we should enable modem + * mode. */ + ier = p->serial_in(p, UART_IER); + + if (ier & UART_IER_MSI) + value |= UART_MCR_MDCE | UART_MCR_FCM; + else + value &= ~(UART_MCR_MDCE | UART_MCR_FCM); + break; + + default: + break; + } + + writeb(value, p->membase + (offset << p->regshift)); +} + +static unsigned int ingenic_uart_serial_in(struct uart_port *p, int offset) +{ + unsigned int value; + + value = readb(p->membase + (offset << p->regshift)); + + /* Hide non-16550 compliant bits from higher levels */ + switch (offset) { + case UART_FCR: + value &= ~UART_FCR_UME; + break; + + case UART_MCR: + value &= ~(UART_MCR_MDCE | UART_MCR_FCM); + break; + + default: + break; + } + return value; +} + +static int ingenic_uart_probe(struct platform_device *pdev) +{ + struct uart_8250_port uart = {}; + struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + struct ingenic_uart_data *data; + const struct ingenic_uart_config *cdata; + const struct of_device_id *match; + int err, line; + + match = of_match_device(of_match, &pdev->dev); + if (!match) { + dev_err(&pdev->dev, "Error: No device match found\n"); + return -ENODEV; + } + cdata = match->data; + + if (!regs || !irq) { + dev_err(&pdev->dev, "no registers/irq defined\n"); + return -EINVAL; + } + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + spin_lock_init(&uart.port.lock); + uart.port.type = PORT_16550A; + uart.port.flags = UPF_SKIP_TEST | UPF_IOREMAP | UPF_FIXED_TYPE; + uart.port.iotype = UPIO_MEM; + uart.port.mapbase = regs->start; + uart.port.regshift = 2; + uart.port.serial_out = ingenic_uart_serial_out; + uart.port.serial_in = ingenic_uart_serial_in; + uart.port.irq = irq->start; + uart.port.dev = &pdev->dev; + uart.port.fifosize = cdata->fifosize; + uart.tx_loadsz = cdata->tx_loadsz; + uart.capabilities = UART_CAP_FIFO | UART_CAP_RTOIE; + + /* Check for a fixed line number */ + line = of_alias_get_id(pdev->dev.of_node, "serial"); + if (line >= 0) + uart.port.line = line; + + uart.port.membase = devm_ioremap(&pdev->dev, regs->start, + resource_size(regs)); + if (!uart.port.membase) + return -ENOMEM; + + data->clk_module = devm_clk_get(&pdev->dev, "module"); + if (IS_ERR(data->clk_module)) { + err = PTR_ERR(data->clk_module); + if (err != -EPROBE_DEFER) + dev_err(&pdev->dev, + "unable to get module clock: %d\n", err); + return err; + } + + data->clk_baud = devm_clk_get(&pdev->dev, "baud"); + if (IS_ERR(data->clk_baud)) { + err = PTR_ERR(data->clk_baud); + if (err != -EPROBE_DEFER) + dev_err(&pdev->dev, + "unable to get baud clock: %d\n", err); + return err; + } + + err = clk_prepare_enable(data->clk_module); + if (err) { + dev_err(&pdev->dev, "could not enable module clock: %d\n", err); + goto out; + } + + err = clk_prepare_enable(data->clk_baud); + if (err) { + dev_err(&pdev->dev, "could not enable baud clock: %d\n", err); + goto out_disable_moduleclk; + } + uart.port.uartclk = clk_get_rate(data->clk_baud); + + data->line = serial8250_register_8250_port(&uart); + if (data->line < 0) { + err = data->line; + goto out_disable_baudclk; + } + + platform_set_drvdata(pdev, data); + return 0; + +out_disable_baudclk: + clk_disable_unprepare(data->clk_baud); +out_disable_moduleclk: + clk_disable_unprepare(data->clk_module); +out: + return err; +} + +static int ingenic_uart_remove(struct platform_device *pdev) +{ + struct ingenic_uart_data *data = platform_get_drvdata(pdev); + + serial8250_unregister_port(data->line); + clk_disable_unprepare(data->clk_module); + clk_disable_unprepare(data->clk_baud); + return 0; +} + +static const struct ingenic_uart_config jz4740_uart_config = { + .tx_loadsz = 8, + .fifosize = 16, +}; + +static const struct ingenic_uart_config jz4760_uart_config = { + .tx_loadsz = 16, + .fifosize = 32, +}; + +static const struct ingenic_uart_config jz4780_uart_config = { + .tx_loadsz = 32, + .fifosize = 64, +}; + +static const struct of_device_id of_match[] = { + { .compatible = "ingenic,jz4740-uart", .data = &jz4740_uart_config }, + { .compatible = "ingenic,jz4760-uart", .data = &jz4760_uart_config }, + { .compatible = "ingenic,jz4775-uart", .data = &jz4760_uart_config }, + { .compatible = "ingenic,jz4780-uart", .data = &jz4780_uart_config }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, of_match); + +static struct platform_driver ingenic_uart_platform_driver = { + .driver = { + .name = "ingenic-uart", + .of_match_table = of_match, + }, + .probe = ingenic_uart_probe, + .remove = ingenic_uart_remove, +}; + +module_platform_driver(ingenic_uart_platform_driver); + +MODULE_AUTHOR("Paul Burton"); +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Ingenic SoC UART driver"); diff --git a/kernel/drivers/tty/serial/8250/8250_lpc18xx.c b/kernel/drivers/tty/serial/8250/8250_lpc18xx.c new file mode 100644 index 000000000..99cd47885 --- /dev/null +++ b/kernel/drivers/tty/serial/8250/8250_lpc18xx.c @@ -0,0 +1,230 @@ +/* + * Serial port driver for NXP LPC18xx/43xx UART + * + * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com> + * + * Based on 8250_mtk.c: + * Copyright (c) 2014 MundoReader S.L. + * Matthias Brugger <matthias.bgg@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include "8250.h" + +/* Additional LPC18xx/43xx 8250 registers and bits */ +#define LPC18XX_UART_RS485CTRL (0x04c / sizeof(u32)) +#define LPC18XX_UART_RS485CTRL_NMMEN BIT(0) +#define LPC18XX_UART_RS485CTRL_DCTRL BIT(4) +#define LPC18XX_UART_RS485CTRL_OINV BIT(5) +#define LPC18XX_UART_RS485DLY (0x054 / sizeof(u32)) +#define LPC18XX_UART_RS485DLY_MAX 255 + +struct lpc18xx_uart_data { + struct uart_8250_dma dma; + struct clk *clk_uart; + struct clk *clk_reg; + int line; +}; + +static int lpc18xx_rs485_config(struct uart_port *port, + struct serial_rs485 *rs485) +{ + struct uart_8250_port *up = up_to_u8250p(port); + u32 rs485_ctrl_reg = 0; + u32 rs485_dly_reg = 0; + unsigned baud_clk; + + if (rs485->flags & SER_RS485_ENABLED) + memset(rs485->padding, 0, sizeof(rs485->padding)); + else + memset(rs485, 0, sizeof(*rs485)); + + rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | + SER_RS485_RTS_AFTER_SEND; + + if (rs485->flags & SER_RS485_ENABLED) { + rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_NMMEN | + LPC18XX_UART_RS485CTRL_DCTRL; + + if (rs485->flags & SER_RS485_RTS_ON_SEND) { + rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_OINV; + rs485->flags &= ~SER_RS485_RTS_AFTER_SEND; + } else { + rs485->flags |= SER_RS485_RTS_AFTER_SEND; + } + } + + if (rs485->delay_rts_after_send) { + baud_clk = port->uartclk / up->dl_read(up); + rs485_dly_reg = DIV_ROUND_UP(rs485->delay_rts_after_send + * baud_clk, MSEC_PER_SEC); + + if (rs485_dly_reg > LPC18XX_UART_RS485DLY_MAX) + rs485_dly_reg = LPC18XX_UART_RS485DLY_MAX; + + /* Calculate the resulting delay in ms */ + rs485->delay_rts_after_send = (rs485_dly_reg * MSEC_PER_SEC) + / baud_clk; + } + + /* Delay RTS before send not supported */ + rs485->delay_rts_before_send = 0; + + serial_out(up, LPC18XX_UART_RS485CTRL, rs485_ctrl_reg); + serial_out(up, LPC18XX_UART_RS485DLY, rs485_dly_reg); + + port->rs485 = *rs485; + + return 0; +} + +static void lpc18xx_uart_serial_out(struct uart_port *p, int offset, int value) +{ + /* + * For DMA mode one must ensure that the UART_FCR_DMA_SELECT + * bit is set when FIFO is enabled. Even if DMA is not used + * setting this bit doesn't seem to affect anything. + */ + if (offset == UART_FCR && (value & UART_FCR_ENABLE_FIFO)) + value |= UART_FCR_DMA_SELECT; + + offset = offset << p->regshift; + writel(value, p->membase + offset); +} + +static int lpc18xx_serial_probe(struct platform_device *pdev) +{ + struct lpc18xx_uart_data *data; + struct uart_8250_port uart; + struct resource *res; + int irq, ret; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "irq not found"); + return irq; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "memory resource not found"); + return -EINVAL; + } + + memset(&uart, 0, sizeof(uart)); + + uart.port.membase = devm_ioremap(&pdev->dev, res->start, + resource_size(res)); + if (!uart.port.membase) + return -ENOMEM; + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->clk_uart = devm_clk_get(&pdev->dev, "uartclk"); + if (IS_ERR(data->clk_uart)) { + dev_err(&pdev->dev, "uart clock not found\n"); + return PTR_ERR(data->clk_uart); + } + + data->clk_reg = devm_clk_get(&pdev->dev, "reg"); + if (IS_ERR(data->clk_reg)) { + dev_err(&pdev->dev, "reg clock not found\n"); + return PTR_ERR(data->clk_reg); + } + + ret = clk_prepare_enable(data->clk_reg); + if (ret) { + dev_err(&pdev->dev, "unable to enable reg clock\n"); + return ret; + } + + ret = clk_prepare_enable(data->clk_uart); + if (ret) { + dev_err(&pdev->dev, "unable to enable uart clock\n"); + goto dis_clk_reg; + } + + ret = of_alias_get_id(pdev->dev.of_node, "serial"); + if (ret >= 0) + uart.port.line = ret; + + data->dma.rx_param = data; + data->dma.tx_param = data; + + spin_lock_init(&uart.port.lock); + uart.port.dev = &pdev->dev; + uart.port.irq = irq; + uart.port.iotype = UPIO_MEM32; + uart.port.mapbase = res->start; + uart.port.regshift = 2; + uart.port.type = PORT_16550A; + uart.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SKIP_TEST; + uart.port.uartclk = clk_get_rate(data->clk_uart); + uart.port.private_data = data; + uart.port.rs485_config = lpc18xx_rs485_config; + uart.port.serial_out = lpc18xx_uart_serial_out; + + uart.dma = &data->dma; + uart.dma->rxconf.src_maxburst = 1; + uart.dma->txconf.dst_maxburst = 1; + + ret = serial8250_register_8250_port(&uart); + if (ret < 0) { + dev_err(&pdev->dev, "unable to register 8250 port\n"); + goto dis_uart_clk; + } + + data->line = ret; + platform_set_drvdata(pdev, data); + + return 0; + +dis_uart_clk: + clk_disable_unprepare(data->clk_uart); +dis_clk_reg: + clk_disable_unprepare(data->clk_reg); + return ret; +} + +static int lpc18xx_serial_remove(struct platform_device *pdev) +{ + struct lpc18xx_uart_data *data = platform_get_drvdata(pdev); + + serial8250_unregister_port(data->line); + clk_disable_unprepare(data->clk_uart); + clk_disable_unprepare(data->clk_reg); + + return 0; +} + +static const struct of_device_id lpc18xx_serial_match[] = { + { .compatible = "nxp,lpc1850-uart" }, + { }, +}; +MODULE_DEVICE_TABLE(of, lpc18xx_serial_match); + +static struct platform_driver lpc18xx_serial_driver = { + .probe = lpc18xx_serial_probe, + .remove = lpc18xx_serial_remove, + .driver = { + .name = "lpc18xx-uart", + .of_match_table = lpc18xx_serial_match, + }, +}; +module_platform_driver(lpc18xx_serial_driver); + +MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>"); +MODULE_DESCRIPTION("Serial port driver NXP LPC18xx/43xx devices"); +MODULE_LICENSE("GPL v2"); diff --git a/kernel/drivers/tty/serial/8250/8250_mid.c b/kernel/drivers/tty/serial/8250/8250_mid.c new file mode 100644 index 000000000..88531a36b --- /dev/null +++ b/kernel/drivers/tty/serial/8250/8250_mid.c @@ -0,0 +1,326 @@ +/* + * 8250_mid.c - Driver for UART on Intel Penwell and various other Intel SOCs + * + * Copyright (C) 2015 Intel Corporation + * Author: Heikki Krogerus <heikki.krogerus@linux.intel.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/rational.h> +#include <linux/module.h> +#include <linux/pci.h> + +#include <linux/dma/hsu.h> + +#include "8250.h" + +#define PCI_DEVICE_ID_INTEL_PNW_UART1 0x081b +#define PCI_DEVICE_ID_INTEL_PNW_UART2 0x081c +#define PCI_DEVICE_ID_INTEL_PNW_UART3 0x081d +#define PCI_DEVICE_ID_INTEL_TNG_UART 0x1191 +#define PCI_DEVICE_ID_INTEL_DNV_UART 0x19d8 + +/* Intel MID Specific registers */ +#define INTEL_MID_UART_PS 0x30 +#define INTEL_MID_UART_MUL 0x34 +#define INTEL_MID_UART_DIV 0x38 + +struct mid8250; + +struct mid8250_board { + unsigned long freq; + unsigned int base_baud; + int (*setup)(struct mid8250 *, struct uart_port *p); + void (*exit)(struct mid8250 *); +}; + +struct mid8250 { + int line; + int dma_index; + struct pci_dev *dma_dev; + struct uart_8250_dma dma; + struct mid8250_board *board; + struct hsu_dma_chip dma_chip; +}; + +/*****************************************************************************/ + +static int pnw_setup(struct mid8250 *mid, struct uart_port *p) +{ + struct pci_dev *pdev = to_pci_dev(p->dev); + + switch (pdev->device) { + case PCI_DEVICE_ID_INTEL_PNW_UART1: + mid->dma_index = 0; + break; + case PCI_DEVICE_ID_INTEL_PNW_UART2: + mid->dma_index = 1; + break; + case PCI_DEVICE_ID_INTEL_PNW_UART3: + mid->dma_index = 2; + break; + default: + return -EINVAL; + } + + mid->dma_dev = pci_get_slot(pdev->bus, + PCI_DEVFN(PCI_SLOT(pdev->devfn), 3)); + return 0; +} + +static int tng_setup(struct mid8250 *mid, struct uart_port *p) +{ + struct pci_dev *pdev = to_pci_dev(p->dev); + int index = PCI_FUNC(pdev->devfn); + + /* Currently no support for HSU port0 */ + if (index-- == 0) + return -ENODEV; + + mid->dma_index = index; + mid->dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(5, 0)); + return 0; +} + +static int dnv_handle_irq(struct uart_port *p) +{ + struct mid8250 *mid = p->private_data; + int ret; + + ret = hsu_dma_irq(&mid->dma_chip, 0); + ret |= hsu_dma_irq(&mid->dma_chip, 1); + + /* For now, letting the HW generate separate interrupt for the UART */ + if (ret) + return ret; + + return serial8250_handle_irq(p, serial_port_in(p, UART_IIR)); +} + +#define DNV_DMA_CHAN_OFFSET 0x80 + +static int dnv_setup(struct mid8250 *mid, struct uart_port *p) +{ + struct hsu_dma_chip *chip = &mid->dma_chip; + struct pci_dev *pdev = to_pci_dev(p->dev); + int ret; + + chip->dev = &pdev->dev; + chip->irq = pdev->irq; + chip->regs = p->membase; + chip->length = pci_resource_len(pdev, 0); + chip->offset = DNV_DMA_CHAN_OFFSET; + + /* Falling back to PIO mode if DMA probing fails */ + ret = hsu_dma_probe(chip); + if (ret) + return 0; + + mid->dma_dev = pdev; + + p->handle_irq = dnv_handle_irq; + return 0; +} + +static void dnv_exit(struct mid8250 *mid) +{ + if (!mid->dma_dev) + return; + hsu_dma_remove(&mid->dma_chip); +} + +/*****************************************************************************/ + +static void mid8250_set_termios(struct uart_port *p, + struct ktermios *termios, + struct ktermios *old) +{ + unsigned int baud = tty_termios_baud_rate(termios); + struct mid8250 *mid = p->private_data; + unsigned short ps = 16; + unsigned long fuart = baud * ps; + unsigned long w = BIT(24) - 1; + unsigned long mul, div; + + if (mid->board->freq < fuart) { + /* Find prescaler value that satisfies Fuart < Fref */ + if (mid->board->freq > baud) + ps = mid->board->freq / baud; /* baud rate too high */ + else + ps = 1; /* PLL case */ + fuart = baud * ps; + } else { + /* Get Fuart closer to Fref */ + fuart *= rounddown_pow_of_two(mid->board->freq / fuart); + } + + rational_best_approximation(fuart, mid->board->freq, w, w, &mul, &div); + p->uartclk = fuart * 16 / ps; /* core uses ps = 16 always */ + + writel(ps, p->membase + INTEL_MID_UART_PS); /* set PS */ + writel(mul, p->membase + INTEL_MID_UART_MUL); /* set MUL */ + writel(div, p->membase + INTEL_MID_UART_DIV); + + serial8250_do_set_termios(p, termios, old); +} + +static bool mid8250_dma_filter(struct dma_chan *chan, void *param) +{ + struct hsu_dma_slave *s = param; + + if (s->dma_dev != chan->device->dev || s->chan_id != chan->chan_id) + return false; + + chan->private = s; + return true; +} + +static int mid8250_dma_setup(struct mid8250 *mid, struct uart_8250_port *port) +{ + struct uart_8250_dma *dma = &mid->dma; + struct device *dev = port->port.dev; + struct hsu_dma_slave *rx_param; + struct hsu_dma_slave *tx_param; + + if (!mid->dma_dev) + return 0; + + rx_param = devm_kzalloc(dev, sizeof(*rx_param), GFP_KERNEL); + if (!rx_param) + return -ENOMEM; + + tx_param = devm_kzalloc(dev, sizeof(*tx_param), GFP_KERNEL); + if (!tx_param) + return -ENOMEM; + + rx_param->chan_id = mid->dma_index * 2 + 1; + tx_param->chan_id = mid->dma_index * 2; + + dma->rxconf.src_maxburst = 64; + dma->txconf.dst_maxburst = 64; + + rx_param->dma_dev = &mid->dma_dev->dev; + tx_param->dma_dev = &mid->dma_dev->dev; + + dma->fn = mid8250_dma_filter; + dma->rx_param = rx_param; + dma->tx_param = tx_param; + + port->dma = dma; + return 0; +} + +static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id) +{ + struct uart_8250_port uart; + struct mid8250 *mid; + int ret; + + ret = pcim_enable_device(pdev); + if (ret) + return ret; + + pci_set_master(pdev); + + mid = devm_kzalloc(&pdev->dev, sizeof(*mid), GFP_KERNEL); + if (!mid) + return -ENOMEM; + + mid->board = (struct mid8250_board *)id->driver_data; + + memset(&uart, 0, sizeof(struct uart_8250_port)); + + uart.port.dev = &pdev->dev; + uart.port.irq = pdev->irq; + uart.port.private_data = mid; + uart.port.type = PORT_16750; + uart.port.iotype = UPIO_MEM; + uart.port.uartclk = mid->board->base_baud * 16; + uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE; + uart.port.set_termios = mid8250_set_termios; + + uart.port.mapbase = pci_resource_start(pdev, 0); + uart.port.membase = pcim_iomap(pdev, 0, 0); + if (!uart.port.membase) + return -ENOMEM; + + if (mid->board->setup) { + ret = mid->board->setup(mid, &uart.port); + if (ret) + return ret; + } + + ret = mid8250_dma_setup(mid, &uart); + if (ret) + goto err; + + ret = serial8250_register_8250_port(&uart); + if (ret < 0) + goto err; + + mid->line = ret; + + pci_set_drvdata(pdev, mid); + return 0; +err: + if (mid->board->exit) + mid->board->exit(mid); + return ret; +} + +static void mid8250_remove(struct pci_dev *pdev) +{ + struct mid8250 *mid = pci_get_drvdata(pdev); + + if (mid->board->exit) + mid->board->exit(mid); + + serial8250_unregister_port(mid->line); +} + +static const struct mid8250_board pnw_board = { + .freq = 50000000, + .base_baud = 115200, + .setup = pnw_setup, +}; + +static const struct mid8250_board tng_board = { + .freq = 38400000, + .base_baud = 1843200, + .setup = tng_setup, +}; + +static const struct mid8250_board dnv_board = { + .freq = 133333333, + .base_baud = 115200, + .setup = dnv_setup, + .exit = dnv_exit, +}; + +#define MID_DEVICE(id, board) { PCI_VDEVICE(INTEL, id), (kernel_ulong_t)&board } + +static const struct pci_device_id pci_ids[] = { + MID_DEVICE(PCI_DEVICE_ID_INTEL_PNW_UART1, pnw_board), + MID_DEVICE(PCI_DEVICE_ID_INTEL_PNW_UART2, pnw_board), + MID_DEVICE(PCI_DEVICE_ID_INTEL_PNW_UART3, pnw_board), + MID_DEVICE(PCI_DEVICE_ID_INTEL_TNG_UART, tng_board), + MID_DEVICE(PCI_DEVICE_ID_INTEL_DNV_UART, dnv_board), + { }, +}; +MODULE_DEVICE_TABLE(pci, pci_ids); + +static struct pci_driver mid8250_pci_driver = { + .name = "8250_mid", + .id_table = pci_ids, + .probe = mid8250_probe, + .remove = mid8250_remove, +}; + +module_pci_driver(mid8250_pci_driver); + +MODULE_AUTHOR("Intel Corporation"); +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("Intel MID UART driver"); diff --git a/kernel/drivers/tty/serial/8250/8250_mtk.c b/kernel/drivers/tty/serial/8250/8250_mtk.c index 7a11fac77..78883ca64 100644 --- a/kernel/drivers/tty/serial/8250/8250_mtk.c +++ b/kernel/drivers/tty/serial/8250/8250_mtk.c @@ -34,6 +34,7 @@ struct mtk8250_data { int line; struct clk *uart_clk; + struct clk *bus_clk; }; static void @@ -115,6 +116,36 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, tty_termios_encode_baud_rate(termios, baud, baud); } +static int mtk8250_runtime_suspend(struct device *dev) +{ + struct mtk8250_data *data = dev_get_drvdata(dev); + + clk_disable_unprepare(data->uart_clk); + clk_disable_unprepare(data->bus_clk); + + return 0; +} + +static int mtk8250_runtime_resume(struct device *dev) +{ + struct mtk8250_data *data = dev_get_drvdata(dev); + int err; + + err = clk_prepare_enable(data->uart_clk); + if (err) { + dev_warn(dev, "Can't enable clock\n"); + return err; + } + + err = clk_prepare_enable(data->bus_clk); + if (err) { + dev_warn(dev, "Can't enable bus clock\n"); + return err; + } + + return 0; +} + static void mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old) { @@ -130,22 +161,24 @@ mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old) static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p, struct mtk8250_data *data) { - int err; - struct device_node *np = pdev->dev.of_node; - - data->uart_clk = of_clk_get(np, 0); + data->uart_clk = devm_clk_get(&pdev->dev, "baud"); if (IS_ERR(data->uart_clk)) { - dev_warn(&pdev->dev, "Can't get timer clock\n"); - return PTR_ERR(data->uart_clk); + /* + * For compatibility with older device trees try unnamed + * clk when no baud clk can be found. + */ + data->uart_clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(data->uart_clk)) { + dev_warn(&pdev->dev, "Can't get uart clock\n"); + return PTR_ERR(data->uart_clk); + } + + return 0; } - err = clk_prepare_enable(data->uart_clk); - if (err) { - dev_warn(&pdev->dev, "Can't prepare clock\n"); - clk_put(data->uart_clk); - return err; - } - p->uartclk = clk_get_rate(data->uart_clk); + data->bus_clk = devm_clk_get(&pdev->dev, "bus"); + if (IS_ERR(data->bus_clk)) + return PTR_ERR(data->bus_clk); return 0; } @@ -190,19 +223,24 @@ static int mtk8250_probe(struct platform_device *pdev) uart.port.regshift = 2; uart.port.private_data = data; uart.port.set_termios = mtk8250_set_termios; + uart.port.uartclk = clk_get_rate(data->uart_clk); /* Disable Rate Fix function */ writel(0x0, uart.port.membase + (MTK_UART_RATE_FIX << uart.port.regshift)); - data->line = serial8250_register_8250_port(&uart); - if (data->line < 0) - return data->line; - platform_set_drvdata(pdev, data); - pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev); + if (!pm_runtime_enabled(&pdev->dev)) { + err = mtk8250_runtime_resume(&pdev->dev); + if (err) + return err; + } + + data->line = serial8250_register_8250_port(&uart); + if (data->line < 0) + return data->line; return 0; } @@ -214,13 +252,13 @@ static int mtk8250_remove(struct platform_device *pdev) pm_runtime_get_sync(&pdev->dev); serial8250_unregister_port(data->line); - if (!IS_ERR(data->uart_clk)) { - clk_disable_unprepare(data->uart_clk); - clk_put(data->uart_clk); - } pm_runtime_disable(&pdev->dev); pm_runtime_put_noidle(&pdev->dev); + + if (!pm_runtime_status_suspended(&pdev->dev)) + mtk8250_runtime_suspend(&pdev->dev); + return 0; } @@ -244,28 +282,6 @@ static int mtk8250_resume(struct device *dev) } #endif /* CONFIG_PM_SLEEP */ -#ifdef CONFIG_PM -static int mtk8250_runtime_suspend(struct device *dev) -{ - struct mtk8250_data *data = dev_get_drvdata(dev); - - if (!IS_ERR(data->uart_clk)) - clk_disable_unprepare(data->uart_clk); - - return 0; -} - -static int mtk8250_runtime_resume(struct device *dev) -{ - struct mtk8250_data *data = dev_get_drvdata(dev); - - if (!IS_ERR(data->uart_clk)) - clk_prepare_enable(data->uart_clk); - - return 0; -} -#endif - static const struct dev_pm_ops mtk8250_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume) SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume, @@ -289,6 +305,21 @@ static struct platform_driver mtk8250_platform_driver = { }; module_platform_driver(mtk8250_platform_driver); +#ifdef CONFIG_SERIAL_8250_CONSOLE +static int __init early_mtk8250_setup(struct earlycon_device *device, + const char *options) +{ + if (!device->port.membase) + return -ENODEV; + + device->port.iotype = UPIO_MEM32; + + return early_serial8250_setup(device, NULL); +} + +OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup); +#endif + MODULE_AUTHOR("Matthias Brugger"); MODULE_LICENSE("GPL"); MODULE_DESCRIPTION("Mediatek 8250 serial port driver"); diff --git a/kernel/drivers/tty/serial/8250/8250_omap.c b/kernel/drivers/tty/serial/8250/8250_omap.c index dce1a2370..a2c0734c7 100644 --- a/kernel/drivers/tty/serial/8250/8250_omap.c +++ b/kernel/drivers/tty/serial/8250/8250_omap.c @@ -16,12 +16,14 @@ #include <linux/platform_device.h> #include <linux/slab.h> #include <linux/of.h> +#include <linux/of_device.h> #include <linux/of_gpio.h> #include <linux/of_irq.h> #include <linux/delay.h> #include <linux/pm_runtime.h> #include <linux/console.h> #include <linux/pm_qos.h> +#include <linux/pm_wakeirq.h> #include <linux/dma-mapping.h> #include "8250.h" @@ -31,6 +33,11 @@ #define UART_ERRATA_i202_MDR1_ACCESS (1 << 0) #define OMAP_UART_WER_HAS_TX_WAKEUP (1 << 1) #define OMAP_DMA_TX_KICK (1 << 2) +/* + * See Advisory 21 in AM437x errata SPRZ408B, updated April 2015. + * The same errata is applicable to AM335x and DRA7x processors too. + */ +#define UART_ERRATA_CLOCK_DISABLE (1 << 3) #define OMAP_UART_FCR_RX_TRIG 6 #define OMAP_UART_FCR_TX_TRIG 4 @@ -52,6 +59,12 @@ #define OMAP_UART_MVR_MAJ_SHIFT 8 #define OMAP_UART_MVR_MIN_MASK 0x3f +/* SYSC register bitmasks */ +#define OMAP_UART_SYSC_SOFTRESET (1 << 1) + +/* SYSS register bitmasks */ +#define OMAP_UART_SYSS_RESETDONE (1 << 0) + #define UART_TI752_TLR_TX 0 #define UART_TI752_TLR_RX 4 @@ -98,6 +111,8 @@ struct omap8250_priv { struct pm_qos_request pm_qos_request; struct work_struct qos_work; struct uart_8250_dma omap8250_dma; + spinlock_t rx_dma_lock; + bool rx_dma_broken; }; static u32 uart_read(struct uart_8250_port *up, u32 reg) @@ -230,6 +245,15 @@ static void omap8250_update_scr(struct uart_8250_port *up, serial_out(up, UART_OMAP_SCR, priv->scr); } +static void omap8250_update_mdr1(struct uart_8250_port *up, + struct omap8250_priv *priv) +{ + if (priv->habit & UART_ERRATA_i202_MDR1_ACCESS) + omap_8250_mdr1_errataset(up, priv); + else + serial_out(up, UART_OMAP_MDR1, priv->mdr1); +} + static void omap8250_restore_regs(struct uart_8250_port *up) { struct omap8250_priv *priv = up->port.private_data; @@ -280,11 +304,9 @@ static void omap8250_restore_regs(struct uart_8250_port *up) serial_out(up, UART_XOFF1, priv->xoff); serial_out(up, UART_LCR, up->lcr); - /* need mode A for FCR */ - if (priv->habit & UART_ERRATA_i202_MDR1_ACCESS) - omap_8250_mdr1_errataset(up, priv); - else - serial_out(up, UART_OMAP_MDR1, priv->mdr1); + + omap8250_update_mdr1(up, priv); + up->port.ops->set_mctrl(&up->port, up->port.mctrl); } @@ -417,7 +439,6 @@ static void omap_8250_set_termios(struct uart_port *port, priv->xoff = termios->c_cc[VSTOP]; priv->efr = 0; - up->mcr &= ~(UART_MCR_RTS | UART_MCR_XONANY); up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF); if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) { @@ -426,12 +447,9 @@ static void omap_8250_set_termios(struct uart_port *port, priv->efr |= UART_EFR_CTS; } else if (up->port.flags & UPF_SOFT_FLOW) { /* - * IXON Flag: - * Enable XON/XOFF flow control on input. - * Receiver compares XON1, XOFF1. + * OMAP rx s/w flow control is borked; the transmitter remains + * stuck off even if rx flow control is subsequently disabled */ - if (termios->c_iflag & IXON) - priv->efr |= OMAP_UART_SW_RX; /* * IXOFF Flag: @@ -442,15 +460,6 @@ static void omap_8250_set_termios(struct uart_port *port, up->port.status |= UPSTAT_AUTOXOFF; priv->efr |= OMAP_UART_SW_TX; } - - /* - * IXANY Flag: - * Enable any character to restart output. - * Operation resumes after receiving any - * character after recognition of the XOFF character - */ - if (termios->c_iflag & IXANY) - up->mcr |= UART_MCR_XONANY; } omap8250_restore_regs(up); @@ -528,14 +537,14 @@ static void omap_serial_fill_features_erratas(struct uart_8250_port *up, switch (revision) { case OMAP_UART_REV_46: - priv->habit = UART_ERRATA_i202_MDR1_ACCESS; + priv->habit |= UART_ERRATA_i202_MDR1_ACCESS; break; case OMAP_UART_REV_52: - priv->habit = UART_ERRATA_i202_MDR1_ACCESS | + priv->habit |= UART_ERRATA_i202_MDR1_ACCESS | OMAP_UART_WER_HAS_TX_WAKEUP; break; case OMAP_UART_REV_63: - priv->habit = UART_ERRATA_i202_MDR1_ACCESS | + priv->habit |= UART_ERRATA_i202_MDR1_ACCESS | OMAP_UART_WER_HAS_TX_WAKEUP; break; default: @@ -551,17 +560,6 @@ static void omap8250_uart_qos_work(struct work_struct *work) pm_qos_update_request(&priv->pm_qos_request, priv->latency); } -static irqreturn_t omap_wake_irq(int irq, void *dev_id) -{ - struct uart_port *port = dev_id; - int ret; - - ret = port->handle_irq(port); - if (ret) - return IRQ_HANDLED; - return IRQ_NONE; -} - #ifdef CONFIG_SERIAL_8250_DMA static int omap_8250_dma_handle_irq(struct uart_port *port); #endif @@ -595,11 +593,9 @@ static int omap_8250_startup(struct uart_port *port) int ret; if (priv->wakeirq) { - ret = request_irq(priv->wakeirq, omap_wake_irq, - port->irqflags, "uart wakeup irq", port); + ret = dev_pm_set_dedicated_wake_irq(port->dev, priv->wakeirq); if (ret) return ret; - disable_irq(priv->wakeirq); } pm_runtime_get_sync(port->dev); @@ -648,8 +644,7 @@ static int omap_8250_startup(struct uart_port *port) err: pm_runtime_mark_last_busy(port->dev); pm_runtime_put_autosuspend(port->dev); - if (priv->wakeirq) - free_irq(priv->wakeirq, port); + dev_pm_clear_wake_irq(port->dev); return ret; } @@ -681,10 +676,8 @@ static void omap_8250_shutdown(struct uart_port *port) pm_runtime_mark_last_busy(port->dev); pm_runtime_put_autosuspend(port->dev); - free_irq(port->irq, port); - if (priv->wakeirq) - free_irq(priv->wakeirq, port); + dev_pm_clear_wake_irq(port->dev); } static void omap_8250_throttle(struct uart_port *port) @@ -726,22 +719,35 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir); static void __dma_rx_do_complete(struct uart_8250_port *p, bool error) { + struct omap8250_priv *priv = p->port.private_data; struct uart_8250_dma *dma = p->dma; struct tty_port *tty_port = &p->port.state->port; struct dma_tx_state state; int count; + unsigned long flags; + int ret; dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr, dma->rx_size, DMA_FROM_DEVICE); + spin_lock_irqsave(&priv->rx_dma_lock, flags); + + if (!dma->rx_running) + goto unlock; + dma->rx_running = 0; dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state); dmaengine_terminate_all(dma->rxchan); count = dma->rx_size - state.residue; - tty_insert_flip_string(tty_port, dma->rx_buf, count); - p->port.icount.rx += count; + ret = tty_insert_flip_string(tty_port, dma->rx_buf, count); + + p->port.icount.rx += ret; + p->port.icount.buf_overrun += count - ret; +unlock: + spin_unlock_irqrestore(&priv->rx_dma_lock, flags); + if (!error) omap_8250_rx_dma(p, 0); @@ -753,28 +759,48 @@ static void __dma_rx_complete(void *param) __dma_rx_do_complete(param, false); } +static void omap_8250_rx_dma_flush(struct uart_8250_port *p) +{ + struct omap8250_priv *priv = p->port.private_data; + struct uart_8250_dma *dma = p->dma; + unsigned long flags; + int ret; + + spin_lock_irqsave(&priv->rx_dma_lock, flags); + + if (!dma->rx_running) { + spin_unlock_irqrestore(&priv->rx_dma_lock, flags); + return; + } + + ret = dmaengine_pause(dma->rxchan); + if (WARN_ON_ONCE(ret)) + priv->rx_dma_broken = true; + + spin_unlock_irqrestore(&priv->rx_dma_lock, flags); + + __dma_rx_do_complete(p, true); +} + static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir) { + struct omap8250_priv *priv = p->port.private_data; struct uart_8250_dma *dma = p->dma; + int err = 0; struct dma_async_tx_descriptor *desc; + unsigned long flags; switch (iir & 0x3f) { case UART_IIR_RLSI: /* 8250_core handles errors and break interrupts */ - if (dma->rx_running) { - dmaengine_pause(dma->rxchan); - __dma_rx_do_complete(p, true); - } + omap_8250_rx_dma_flush(p); return -EIO; case UART_IIR_RX_TIMEOUT: /* * If RCVR FIFO trigger level was not reached, complete the * transfer and let 8250_core copy the remaining data. */ - if (dma->rx_running) { - dmaengine_pause(dma->rxchan); - __dma_rx_do_complete(p, true); - } + omap_8250_rx_dma_flush(p); return -ETIMEDOUT; case UART_IIR_RDI: /* @@ -786,24 +812,28 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir) * the DMA won't do anything soon so we have to cancel the DMA * transfer and purge the FIFO manually. */ - if (dma->rx_running) { - dmaengine_pause(dma->rxchan); - __dma_rx_do_complete(p, true); - } + omap_8250_rx_dma_flush(p); return -ETIMEDOUT; default: break; } + if (priv->rx_dma_broken) + return -EINVAL; + + spin_lock_irqsave(&priv->rx_dma_lock, flags); + if (dma->rx_running) - return 0; + goto out; desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr, dma->rx_size, DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); - if (!desc) - return -EBUSY; + if (!desc) { + err = -EBUSY; + goto out; + } dma->rx_running = 1; desc->callback = __dma_rx_complete; @@ -815,7 +845,9 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir) dma->rx_size, DMA_FROM_DEVICE); dma_async_issue_pending(dma->rxchan); - return 0; +out: + spin_unlock_irqrestore(&priv->rx_dma_lock, flags); + return err; } static int omap_8250_tx_dma(struct uart_8250_port *p); @@ -1038,6 +1070,20 @@ static int omap8250_no_handle_irq(struct uart_port *port) return 0; } +static const u8 am3352_habit = OMAP_DMA_TX_KICK | UART_ERRATA_CLOCK_DISABLE; +static const u8 am4372_habit = UART_ERRATA_CLOCK_DISABLE; + +static const struct of_device_id omap8250_dt_ids[] = { + { .compatible = "ti,omap2-uart" }, + { .compatible = "ti,omap3-uart" }, + { .compatible = "ti,omap4-uart" }, + { .compatible = "ti,am3352-uart", .data = &am3352_habit, }, + { .compatible = "ti,am4372-uart", .data = &am4372_habit, }, + { .compatible = "ti,dra742-uart", .data = &am4372_habit, }, + {}, +}; +MODULE_DEVICE_TABLE(of, omap8250_dt_ids); + static int omap8250_probe(struct platform_device *pdev) { struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -1102,11 +1148,17 @@ static int omap8250_probe(struct platform_device *pdev) up.port.unthrottle = omap_8250_unthrottle; if (pdev->dev.of_node) { + const struct of_device_id *id; + ret = of_alias_get_id(pdev->dev.of_node, "serial"); of_property_read_u32(pdev->dev.of_node, "clock-frequency", &up.port.uartclk); priv->wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1); + + id = of_match_device(of_match_ptr(omap8250_dt_ids), &pdev->dev); + if (id && id->data) + priv->habit |= *(u8 *)id->data; } else { ret = pdev->id; } @@ -1129,6 +1181,8 @@ static int omap8250_probe(struct platform_device *pdev) priv->latency); INIT_WORK(&priv->qos_work, omap8250_uart_qos_work); + spin_lock_init(&priv->rx_dma_lock); + device_init_wakeup(&pdev->dev, true); pm_runtime_use_autosuspend(&pdev->dev); pm_runtime_set_autosuspend_delay(&pdev->dev, -1); @@ -1162,6 +1216,11 @@ static int omap8250_probe(struct platform_device *pdev) if (of_machine_is_compatible("ti,am33xx")) priv->habit |= OMAP_DMA_TX_KICK; + /* + * pause is currently not supported atleast on omap-sdma + * and edma on most earlier kernels. + */ + priv->rx_dma_broken = true; } } #endif @@ -1193,31 +1252,6 @@ static int omap8250_remove(struct platform_device *pdev) return 0; } -#ifdef CONFIG_PM - -static inline void omap8250_enable_wakeirq(struct omap8250_priv *priv, - bool enable) -{ - if (!priv->wakeirq) - return; - - if (enable) - enable_irq(priv->wakeirq); - else - disable_irq_nosync(priv->wakeirq); -} - -static void omap8250_enable_wakeup(struct omap8250_priv *priv, - bool enable) -{ - if (enable == priv->wakeups_enabled) - return; - - omap8250_enable_wakeirq(priv, enable); - priv->wakeups_enabled = enable; -} -#endif - #ifdef CONFIG_PM_SLEEP static int omap8250_prepare(struct device *dev) { @@ -1244,11 +1278,6 @@ static int omap8250_suspend(struct device *dev) serial8250_suspend_port(priv->line); flush_work(&priv->qos_work); - - if (device_may_wakeup(dev)) - omap8250_enable_wakeup(priv, true); - else - omap8250_enable_wakeup(priv, false); return 0; } @@ -1256,9 +1285,6 @@ static int omap8250_resume(struct device *dev) { struct omap8250_priv *priv = dev_get_drvdata(dev); - if (device_may_wakeup(dev)) - omap8250_enable_wakeup(priv, false); - serial8250_resume_port(priv->line); return 0; } @@ -1272,17 +1298,46 @@ static int omap8250_lost_context(struct uart_8250_port *up) { u32 val; - val = serial_in(up, UART_OMAP_MDR1); + val = serial_in(up, UART_OMAP_SCR); /* - * If we lose context, then MDR1 is set to its reset value which is - * UART_OMAP_MDR1_DISABLE. After set_termios() we set it either to 13x - * or 16x but never to disable again. + * If we lose context, then SCR is set to its reset value of zero. + * After set_termios() we set bit 3 of SCR (TX_EMPTY_CTL_IT) to 1, + * among other bits, to never set the register back to zero again. */ - if (val == UART_OMAP_MDR1_DISABLE) + if (!val) return 1; return 0; } +/* TODO: in future, this should happen via API in drivers/reset/ */ +static int omap8250_soft_reset(struct device *dev) +{ + struct omap8250_priv *priv = dev_get_drvdata(dev); + struct uart_8250_port *up = serial8250_get_port(priv->line); + int timeout = 100; + int sysc; + int syss; + + sysc = serial_in(up, UART_OMAP_SYSC); + + /* softreset the UART */ + sysc |= OMAP_UART_SYSC_SOFTRESET; + serial_out(up, UART_OMAP_SYSC, sysc); + + /* By experiments, 1us enough for reset complete on AM335x */ + do { + udelay(1); + syss = serial_in(up, UART_OMAP_SYSS); + } while (--timeout && !(syss & OMAP_UART_SYSS_RESETDONE)); + + if (!timeout) { + dev_err(dev, "timed out waiting for reset done\n"); + return -ETIMEDOUT; + } + + return 0; +} + static int omap8250_runtime_suspend(struct device *dev) { struct omap8250_priv *priv = dev_get_drvdata(dev); @@ -1300,8 +1355,18 @@ static int omap8250_runtime_suspend(struct device *dev) return -EBUSY; } - omap8250_enable_wakeup(priv, true); - if (up->dma) + if (priv->habit & UART_ERRATA_CLOCK_DISABLE) { + int ret; + + ret = omap8250_soft_reset(dev); + if (ret) + return ret; + + /* Restore to UART mode after reset (for wakeup) */ + omap8250_update_mdr1(up, priv); + } + + if (up->dma && up->dma->rxchan) omap_8250_rx_dma(up, UART_IIR_RX_TIMEOUT); priv->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE; @@ -1321,13 +1386,12 @@ static int omap8250_runtime_resume(struct device *dev) return 0; up = serial8250_get_port(priv->line); - omap8250_enable_wakeup(priv, false); loss_cntx = omap8250_lost_context(up); if (loss_cntx) omap8250_restore_regs(up); - if (up->dma) + if (up->dma && up->dma->rxchan) omap_8250_rx_dma(up, 0); priv->latency = priv->calc_latency; @@ -1384,14 +1448,6 @@ static const struct dev_pm_ops omap8250_dev_pm_ops = { .complete = omap8250_complete, }; -static const struct of_device_id omap8250_dt_ids[] = { - { .compatible = "ti,omap2-uart" }, - { .compatible = "ti,omap3-uart" }, - { .compatible = "ti,omap4-uart" }, - {}, -}; -MODULE_DEVICE_TABLE(of, omap8250_dt_ids); - static struct platform_driver omap8250_platform_driver = { .driver = { .name = "omap8250", diff --git a/kernel/drivers/tty/serial/8250/8250_pci.c b/kernel/drivers/tty/serial/8250/8250_pci.c index 9373cca12..7cd6f9a90 100644 --- a/kernel/drivers/tty/serial/8250/8250_pci.c +++ b/kernel/drivers/tty/serial/8250/8250_pci.c @@ -28,7 +28,6 @@ #include <linux/dmaengine.h> #include <linux/platform_data/dma-dw.h> -#include <linux/platform_data/dma-hsu.h> #include "8250.h" @@ -1380,6 +1379,9 @@ ce4100_serial_setup(struct serial_private *priv, #define PCI_DEVICE_ID_INTEL_BSW_UART1 0x228a #define PCI_DEVICE_ID_INTEL_BSW_UART2 0x228c +#define PCI_DEVICE_ID_INTEL_BDW_UART1 0x9ce3 +#define PCI_DEVICE_ID_INTEL_BDW_UART2 0x9ce4 + #define BYT_PRV_CLK 0x800 #define BYT_PRV_CLK_EN (1 << 0) #define BYT_PRV_CLK_M_VAL_SHIFT 1 @@ -1417,6 +1419,10 @@ byt_set_termios(struct uart_port *p, struct ktermios *termios, reg |= BYT_PRV_CLK_EN | BYT_PRV_CLK_UPDATE; writel(reg, p->membase + BYT_PRV_CLK); + p->status &= ~UPSTAT_AUTOCTS; + if (termios->c_cflag & CRTSCTS) + p->status |= UPSTAT_AUTOCTS; + serial8250_do_set_termios(p, termios, old); } @@ -1458,11 +1464,13 @@ byt_serial_setup(struct serial_private *priv, switch (pdev->device) { case PCI_DEVICE_ID_INTEL_BYT_UART1: case PCI_DEVICE_ID_INTEL_BSW_UART1: + case PCI_DEVICE_ID_INTEL_BDW_UART1: rx_param->src_id = 3; tx_param->dst_id = 2; break; case PCI_DEVICE_ID_INTEL_BYT_UART2: case PCI_DEVICE_ID_INTEL_BSW_UART2: + case PCI_DEVICE_ID_INTEL_BDW_UART2: rx_param->src_id = 5; tx_param->dst_id = 4; break; @@ -1504,185 +1512,77 @@ byt_serial_setup(struct serial_private *priv, return ret; } -#define INTEL_MID_UART_PS 0x30 -#define INTEL_MID_UART_MUL 0x34 -#define INTEL_MID_UART_DIV 0x38 - -static void intel_mid_set_termios(struct uart_port *p, - struct ktermios *termios, - struct ktermios *old, - unsigned long fref) +static int +pci_omegapci_setup(struct serial_private *priv, + const struct pciserial_board *board, + struct uart_8250_port *port, int idx) { - unsigned int baud = tty_termios_baud_rate(termios); - unsigned short ps = 16; - unsigned long fuart = baud * ps; - unsigned long w = BIT(24) - 1; - unsigned long mul, div; - - if (fref < fuart) { - /* Find prescaler value that satisfies Fuart < Fref */ - if (fref > baud) - ps = fref / baud; /* baud rate too high */ - else - ps = 1; /* PLL case */ - fuart = baud * ps; - } else { - /* Get Fuart closer to Fref */ - fuart *= rounddown_pow_of_two(fref / fuart); - } - - rational_best_approximation(fuart, fref, w, w, &mul, &div); - p->uartclk = fuart * 16 / ps; /* core uses ps = 16 always */ - - writel(ps, p->membase + INTEL_MID_UART_PS); /* set PS */ - writel(mul, p->membase + INTEL_MID_UART_MUL); /* set MUL */ - writel(div, p->membase + INTEL_MID_UART_DIV); - - serial8250_do_set_termios(p, termios, old); + return setup_port(priv, port, 2, idx * 8, 0); } -static void intel_mid_set_termios_38_4M(struct uart_port *p, - struct ktermios *termios, - struct ktermios *old) +static int +pci_brcm_trumanage_setup(struct serial_private *priv, + const struct pciserial_board *board, + struct uart_8250_port *port, int idx) { - intel_mid_set_termios(p, termios, old, 38400000); -} + int ret = pci_default_setup(priv, board, port, idx); -static void intel_mid_set_termios_50M(struct uart_port *p, - struct ktermios *termios, - struct ktermios *old) -{ - /* - * The uart clk is 50Mhz, and the baud rate come from: - * baud = 50M * MUL / (DIV * PS * DLAB) - */ - intel_mid_set_termios(p, termios, old, 50000000); + port->port.type = PORT_BRCM_TRUMANAGE; + port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE); + return ret; } -static bool intel_mid_dma_filter(struct dma_chan *chan, void *param) -{ - struct hsu_dma_slave *s = param; - - if (s->dma_dev != chan->device->dev || s->chan_id != chan->chan_id) - return false; - - chan->private = s; - return true; -} +/* RTS will control by MCR if this bit is 0 */ +#define FINTEK_RTS_CONTROL_BY_HW BIT(4) +/* only worked with FINTEK_RTS_CONTROL_BY_HW on */ +#define FINTEK_RTS_INVERT BIT(5) -static int intel_mid_serial_setup(struct serial_private *priv, - const struct pciserial_board *board, - struct uart_8250_port *port, int idx, - int index, struct pci_dev *dma_dev) +/* We should do proper H/W transceiver setting before change to RS485 mode */ +static int pci_fintek_rs485_config(struct uart_port *port, + struct serial_rs485 *rs485) { - struct device *dev = port->port.dev; - struct uart_8250_dma *dma; - struct hsu_dma_slave *tx_param, *rx_param; - - dma = devm_kzalloc(dev, sizeof(*dma), GFP_KERNEL); - if (!dma) - return -ENOMEM; - - tx_param = devm_kzalloc(dev, sizeof(*tx_param), GFP_KERNEL); - if (!tx_param) - return -ENOMEM; + u8 setting; + u8 *index = (u8 *) port->private_data; + struct pci_dev *pci_dev = container_of(port->dev, struct pci_dev, + dev); - rx_param = devm_kzalloc(dev, sizeof(*rx_param), GFP_KERNEL); - if (!rx_param) - return -ENOMEM; + pci_read_config_byte(pci_dev, 0x40 + 8 * *index + 7, &setting); - rx_param->chan_id = index * 2 + 1; - tx_param->chan_id = index * 2; - - dma->rxconf.src_maxburst = 64; - dma->txconf.dst_maxburst = 64; - - rx_param->dma_dev = &dma_dev->dev; - tx_param->dma_dev = &dma_dev->dev; - - dma->fn = intel_mid_dma_filter; - dma->rx_param = rx_param; - dma->tx_param = tx_param; - - port->port.type = PORT_16750; - port->port.flags |= UPF_FIXED_PORT | UPF_FIXED_TYPE; - port->dma = dma; + if (!rs485) + rs485 = &port->rs485; + else if (rs485->flags & SER_RS485_ENABLED) + memset(rs485->padding, 0, sizeof(rs485->padding)); + else + memset(rs485, 0, sizeof(*rs485)); - return pci_default_setup(priv, board, port, idx); -} + /* F81504/508/512 not support RTS delay before or after send */ + rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND; -#define PCI_DEVICE_ID_INTEL_PNW_UART1 0x081b -#define PCI_DEVICE_ID_INTEL_PNW_UART2 0x081c -#define PCI_DEVICE_ID_INTEL_PNW_UART3 0x081d + if (rs485->flags & SER_RS485_ENABLED) { + /* Enable RTS H/W control mode */ + setting |= FINTEK_RTS_CONTROL_BY_HW; -static int pnw_serial_setup(struct serial_private *priv, - const struct pciserial_board *board, - struct uart_8250_port *port, int idx) -{ - struct pci_dev *pdev = priv->dev; - struct pci_dev *dma_dev; - int index; + if (rs485->flags & SER_RS485_RTS_ON_SEND) { + /* RTS driving high on TX */ + setting &= ~FINTEK_RTS_INVERT; + } else { + /* RTS driving low on TX */ + setting |= FINTEK_RTS_INVERT; + } - switch (pdev->device) { - case PCI_DEVICE_ID_INTEL_PNW_UART1: - index = 0; - break; - case PCI_DEVICE_ID_INTEL_PNW_UART2: - index = 1; - break; - case PCI_DEVICE_ID_INTEL_PNW_UART3: - index = 2; - break; - default: - return -EINVAL; + rs485->delay_rts_after_send = 0; + rs485->delay_rts_before_send = 0; + } else { + /* Disable RTS H/W control mode */ + setting &= ~(FINTEK_RTS_CONTROL_BY_HW | FINTEK_RTS_INVERT); } - dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(PCI_SLOT(pdev->devfn), 3)); - - port->port.set_termios = intel_mid_set_termios_50M; + pci_write_config_byte(pci_dev, 0x40 + 8 * *index + 7, setting); - return intel_mid_serial_setup(priv, board, port, idx, index, dma_dev); -} - -#define PCI_DEVICE_ID_INTEL_TNG_UART 0x1191 - -static int tng_serial_setup(struct serial_private *priv, - const struct pciserial_board *board, - struct uart_8250_port *port, int idx) -{ - struct pci_dev *pdev = priv->dev; - struct pci_dev *dma_dev; - int index = PCI_FUNC(pdev->devfn); - - /* Currently no support for HSU port0 */ - if (index-- == 0) - return -ENODEV; - - dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(5, 0)); - - port->port.set_termios = intel_mid_set_termios_38_4M; + if (rs485 != &port->rs485) + port->rs485 = *rs485; - return intel_mid_serial_setup(priv, board, port, idx, index, dma_dev); -} - -static int -pci_omegapci_setup(struct serial_private *priv, - const struct pciserial_board *board, - struct uart_8250_port *port, int idx) -{ - return setup_port(priv, port, 2, idx * 8, 0); -} - -static int -pci_brcm_trumanage_setup(struct serial_private *priv, - const struct pciserial_board *board, - struct uart_8250_port *port, int idx) -{ - int ret = pci_default_setup(priv, board, port, idx); - - port->port.type = PORT_BRCM_TRUMANAGE; - port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE); - return ret; + return 0; } static int pci_fintek_setup(struct serial_private *priv, @@ -1690,6 +1590,7 @@ static int pci_fintek_setup(struct serial_private *priv, struct uart_8250_port *port, int idx) { struct pci_dev *pdev = priv->dev; + u8 *data; u8 config_base; u16 iobase; @@ -1702,6 +1603,15 @@ static int pci_fintek_setup(struct serial_private *priv, port->port.iotype = UPIO_PORT; port->port.iobase = iobase; + port->port.rs485_config = pci_fintek_rs485_config; + + data = devm_kzalloc(&pdev->dev, sizeof(u8), GFP_KERNEL); + if (!data) + return -ENOMEM; + + /* preserve index in PCI configuration space */ + *data = idx; + port->port.private_data = data; return 0; } @@ -1712,6 +1622,8 @@ static int pci_fintek_init(struct pci_dev *dev) u32 max_port, i; u32 bar_data[3]; u8 config_base; + struct serial_private *priv = pci_get_drvdata(dev); + struct uart_8250_port *port; switch (dev->device) { case 0x1104: /* 4 ports */ @@ -1752,6 +1664,19 @@ static int pci_fintek_init(struct pci_dev *dev) (u8)((iobase & 0xff00) >> 8)); pci_write_config_byte(dev, config_base + 0x06, dev->irq); + + if (priv) { + /* re-apply RS232/485 mode when + * pciserial_resume_ports() + */ + port = serial8250_get_port(priv->line[i]); + pci_fintek_rs485_config(&port->port, NULL); + } else { + /* First init without port data + * force init to RS232 Mode + */ + pci_write_config_byte(dev, config_base + 0x07, 0x01); + } } return max_port; @@ -1823,6 +1748,9 @@ static int pci_eg20t_init(struct pci_dev *dev) #endif } +#define PCI_DEVICE_ID_EXAR_XR17V4358 0x4358 +#define PCI_DEVICE_ID_EXAR_XR17V8358 0x8358 + static int pci_xr17c154_setup(struct serial_private *priv, const struct pciserial_board *board, @@ -1832,6 +1760,15 @@ pci_xr17c154_setup(struct serial_private *priv, return pci_default_setup(priv, board, port, idx); } +static inline int +xr17v35x_has_slave(struct serial_private *priv) +{ + const int dev_id = priv->dev->device; + + return ((dev_id == PCI_DEVICE_ID_EXAR_XR17V4358) || + (dev_id == PCI_DEVICE_ID_EXAR_XR17V8358)); +} + static int pci_xr17v35x_setup(struct serial_private *priv, const struct pciserial_board *board, @@ -1846,6 +1783,13 @@ pci_xr17v35x_setup(struct serial_private *priv, port->port.flags |= UPF_EXAR_EFR; /* + * Setup the uart clock for the devices on expansion slot to + * half the clock speed of the main chip (which is 125MHz) + */ + if (xr17v35x_has_slave(priv) && idx >= 8) + port->port.uartclk = (7812500 * 16 / 2); + + /* * Setup Multipurpose Input/Output pins. */ if (idx == 0) { @@ -1997,8 +1941,7 @@ pci_wch_ch38x_setup(struct serial_private *priv, #define PCIE_VENDOR_ID_WCH 0x1c00 #define PCIE_DEVICE_ID_WCH_CH382_2S1P 0x3250 #define PCIE_DEVICE_ID_WCH_CH384_4S 0x3470 - -#define PCI_DEVICE_ID_EXAR_XR17V8358 0x8358 +#define PCIE_DEVICE_ID_WCH_CH382_2S 0x3253 #define PCI_VENDOR_ID_PERICOM 0x12D8 #define PCI_DEVICE_ID_PERICOM_PI7C9X7951 0x7951 @@ -2113,42 +2056,28 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { }, { .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_PNW_UART1, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .setup = pnw_serial_setup, - }, - { - .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_PNW_UART2, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .setup = pnw_serial_setup, - }, - { - .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_PNW_UART3, + .device = PCI_DEVICE_ID_INTEL_BSW_UART1, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pnw_serial_setup, + .setup = byt_serial_setup, }, { .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_TNG_UART, + .device = PCI_DEVICE_ID_INTEL_BSW_UART2, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = tng_serial_setup, + .setup = byt_serial_setup, }, { .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_BSW_UART1, + .device = PCI_DEVICE_ID_INTEL_BDW_UART1, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, .setup = byt_serial_setup, }, { .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_BSW_UART2, + .device = PCI_DEVICE_ID_INTEL_BDW_UART2, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, .setup = byt_serial_setup, @@ -2515,6 +2444,13 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { }, { .vendor = PCI_VENDOR_ID_EXAR, + .device = PCI_DEVICE_ID_EXAR_XR17V4358, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_xr17v35x_setup, + }, + { + .vendor = PCI_VENDOR_ID_EXAR, .device = PCI_DEVICE_ID_EXAR_XR17V8358, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, @@ -2702,6 +2638,14 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .subdevice = PCI_ANY_ID, .setup = pci_wch_ch353_setup, }, + /* WCH CH382 2S card (16850 clone) */ + { + .vendor = PCIE_VENDOR_ID_WCH, + .device = PCIE_DEVICE_ID_WCH_CH382_2S, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_wch_ch38x_setup, + }, /* WCH CH382 2S1P card (16850 clone) */ { .vendor = PCIE_VENDOR_ID_WCH, @@ -2999,6 +2943,7 @@ enum pci_board_num_t { pbn_exar_XR17V352, pbn_exar_XR17V354, pbn_exar_XR17V358, + pbn_exar_XR17V4358, pbn_exar_XR17V8358, pbn_exar_ibm_saturn, pbn_pasemi_1682M, @@ -3012,8 +2957,6 @@ enum pci_board_num_t { pbn_ADDIDATA_PCIe_8_3906250, pbn_ce4100_1_115200, pbn_byt, - pbn_pnw, - pbn_tng, pbn_qrk, pbn_omegapci, pbn_NETMOS9900_2s_115200, @@ -3021,6 +2964,7 @@ enum pci_board_num_t { pbn_fintek_4, pbn_fintek_8, pbn_fintek_12, + pbn_wch382_2, pbn_wch384_4, pbn_pericom_PI7C9X7951, pbn_pericom_PI7C9X7952, @@ -3690,6 +3634,14 @@ static struct pciserial_board pci_boards[] = { .reg_shift = 0, .first_offset = 0, }, + [pbn_exar_XR17V4358] = { + .flags = FL_BASE0, + .num_ports = 12, + .base_baud = 7812500, + .uart_offset = 0x400, + .reg_shift = 0, + .first_offset = 0, + }, [pbn_exar_XR17V8358] = { .flags = FL_BASE0, .num_ports = 16, @@ -3792,16 +3744,6 @@ static struct pciserial_board pci_boards[] = { .uart_offset = 0x80, .reg_shift = 2, }, - [pbn_pnw] = { - .flags = FL_BASE0, - .num_ports = 1, - .base_baud = 115200, - }, - [pbn_tng] = { - .flags = FL_BASE0, - .num_ports = 1, - .base_baud = 1843200, - }, [pbn_qrk] = { .flags = FL_BASE0, .num_ports = 1, @@ -3843,6 +3785,13 @@ static struct pciserial_board pci_boards[] = { .base_baud = 115200, .first_offset = 0x40, }, + [pbn_wch382_2] = { + .flags = FL_BASE0, + .num_ports = 2, + .base_baud = 115200, + .uart_offset = 8, + .first_offset = 0xC0, + }, [pbn_wch384_4] = { .flags = FL_BASE0, .num_ports = 4, @@ -3890,6 +3839,13 @@ static const struct pci_device_id blacklist[] = { { PCI_DEVICE(0x4348, 0x5053), }, /* WCH CH353 1S1P */ { PCI_DEVICE(0x1c00, 0x3250), }, /* WCH CH382 2S1P */ { PCI_DEVICE(0x1c00, 0x3470), }, /* WCH CH384 4S */ + + /* Intel platforms with MID UART */ + { PCI_VDEVICE(INTEL, 0x081b), }, + { PCI_VDEVICE(INTEL, 0x081c), }, + { PCI_VDEVICE(INTEL, 0x081d), }, + { PCI_VDEVICE(INTEL, 0x1191), }, + { PCI_VDEVICE(INTEL, 0x19d8), }, }; /* @@ -5133,6 +5089,10 @@ static struct pci_device_id serial_pci_tbl[] = { PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_exar_XR17V358 }, + { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V4358, + PCI_ANY_ID, PCI_ANY_ID, + 0, + 0, pbn_exar_XR17V4358 }, { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V8358, PCI_ANY_ID, PCI_ANY_ID, 0, @@ -5582,25 +5542,15 @@ static struct pci_device_id serial_pci_tbl[] = { PCI_CLASS_COMMUNICATION_SERIAL << 8, 0xff0000, pbn_byt }, - /* - * Intel Penwell - */ - { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PNW_UART1, - PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pnw}, - { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PNW_UART2, - PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pnw}, - { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PNW_UART3, - PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_pnw}, - - /* - * Intel Tangier - */ - { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TNG_UART, - PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_tng}, + /* Intel Broadwell */ + { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_BDW_UART1, + PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_COMMUNICATION_SERIAL << 8, 0xff0000, + pbn_byt }, + { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_BDW_UART2, + PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_COMMUNICATION_SERIAL << 8, 0xff0000, + pbn_byt }, /* * Intel Quark x1000 @@ -5641,6 +5591,10 @@ static struct pci_device_id serial_pci_tbl[] = { PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_b0_bt_2_115200 }, + { PCIE_VENDOR_ID_WCH, PCIE_DEVICE_ID_WCH_CH382_2S, + PCI_ANY_ID, PCI_ANY_ID, + 0, 0, pbn_wch382_2 }, + { PCIE_VENDOR_ID_WCH, PCIE_DEVICE_ID_WCH_CH384_4S, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_wch384_4 }, diff --git a/kernel/drivers/tty/serial/8250/8250_port.c b/kernel/drivers/tty/serial/8250/8250_port.c new file mode 100644 index 000000000..5568d70ee --- /dev/null +++ b/kernel/drivers/tty/serial/8250/8250_port.c @@ -0,0 +1,2935 @@ +/* + * Base port operations for 8250/16550-type serial ports + * + * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. + * Split from 8250_core.c, Copyright (C) 2001 Russell King. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * A note about mapbase / membase + * + * mapbase is the physical address of the IO port. + * membase is an 'ioremapped' cookie. + */ + +#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/tty.h> +#include <linux/ratelimit.h> +#include <linux/tty_flip.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> +#include <linux/nmi.h> +#include <linux/mutex.h> +#include <linux/slab.h> +#include <linux/kdb.h> +#include <linux/uaccess.h> +#include <linux/pm_runtime.h> + +#include <asm/io.h> +#include <asm/irq.h> + +#include "8250.h" + +/* + * Debugging. + */ +#if 0 +#define DEBUG_AUTOCONF(fmt...) printk(fmt) +#else +#define DEBUG_AUTOCONF(fmt...) do { } while (0) +#endif + +#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial8250_config uart_config[] = { + [PORT_UNKNOWN] = { + .name = "unknown", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_8250] = { + .name = "8250", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16450] = { + .name = "16450", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550] = { + .name = "16550", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550A] = { + .name = "16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .rxtrig_bytes = {1, 4, 8, 14}, + .flags = UART_CAP_FIFO, + }, + [PORT_CIRRUS] = { + .name = "Cirrus", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16650] = { + .name = "ST16650", + .fifo_size = 1, + .tx_loadsz = 1, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16650V2] = { + .name = "ST16650V2", + .fifo_size = 32, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_00, + .rxtrig_bytes = {8, 16, 24, 28}, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16750] = { + .name = "TI16750", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | + UART_FCR7_64BYTE, + .rxtrig_bytes = {1, 16, 32, 56}, + .flags = UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE, + }, + [PORT_STARTECH] = { + .name = "Startech", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16C950] = { + .name = "16C950/954", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + /* UART_CAP_EFR breaks billionon CF bluetooth card. */ + .flags = UART_CAP_FIFO | UART_CAP_SLEEP, + }, + [PORT_16654] = { + .name = "ST16654", + .fifo_size = 64, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_10, + .rxtrig_bytes = {8, 16, 56, 60}, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16850] = { + .name = "XR16850", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_RSA] = { + .name = "RSA", + .fifo_size = 2048, + .tx_loadsz = 2048, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11, + .flags = UART_CAP_FIFO, + }, + [PORT_NS16550A] = { + .name = "NS16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_NATSEMI, + }, + [PORT_XSCALE] = { + .name = "XScale", + .fifo_size = 32, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE, + }, + [PORT_OCTEON] = { + .name = "OCTEON", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO, + }, + [PORT_AR7] = { + .name = "AR7", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_U6_16550A] = { + .name = "U6_16550A", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_TEGRA] = { + .name = "Tegra", + .fifo_size = 32, + .tx_loadsz = 8, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_01, + .rxtrig_bytes = {1, 4, 8, 14}, + .flags = UART_CAP_FIFO | UART_CAP_RTOIE, + }, + [PORT_XR17D15X] = { + .name = "XR17D15X", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP, + }, + [PORT_XR17V35X] = { + .name = "XR17V35X", + .fifo_size = 256, + .tx_loadsz = 256, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 | + UART_FCR_T_TRIG_11, + .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP, + }, + [PORT_LPC3220] = { + .name = "LPC3220", + .fifo_size = 64, + .tx_loadsz = 32, + .fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO | + UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00, + .flags = UART_CAP_FIFO, + }, + [PORT_BRCM_TRUMANAGE] = { + .name = "TruManage", + .fifo_size = 1, + .tx_loadsz = 1024, + .flags = UART_CAP_HFIFO, + }, + [PORT_8250_CIR] = { + .name = "CIR port" + }, + [PORT_ALTR_16550_F32] = { + .name = "Altera 16550 FIFO32", + .fifo_size = 32, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_ALTR_16550_F64] = { + .name = "Altera 16550 FIFO64", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_ALTR_16550_F128] = { + .name = "Altera 16550 FIFO128", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, +/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement +workaround of errata A-008006 which states that tx_loadsz should be +configured less than Maximum supported fifo bytes */ + [PORT_16550A_FSL64] = { + .name = "16550A_FSL64", + .fifo_size = 64, + .tx_loadsz = 63, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | + UART_FCR7_64BYTE, + .flags = UART_CAP_FIFO, + }, + [PORT_RT2880] = { + .name = "Palmchip BK-3103", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .rxtrig_bytes = {1, 4, 8, 14}, + .flags = UART_CAP_FIFO, + }, +}; + +/* Uart divisor latch read */ +static int default_serial_dl_read(struct uart_8250_port *up) +{ + return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static void default_serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_out(up, UART_DLL, value & 0xff); + serial_out(up, UART_DLM, value >> 8 & 0xff); +} + +#ifdef CONFIG_SERIAL_8250_RT288X + +/* Au1x00/RT288x UART hardware has a weird register layout */ +static const s8 au_io_in_map[8] = { + 0, /* UART_RX */ + 2, /* UART_IER */ + 3, /* UART_IIR */ + 5, /* UART_LCR */ + 6, /* UART_MCR */ + 7, /* UART_LSR */ + 8, /* UART_MSR */ + -1, /* UART_SCR (unmapped) */ +}; + +static const s8 au_io_out_map[8] = { + 1, /* UART_TX */ + 2, /* UART_IER */ + 4, /* UART_FCR */ + 5, /* UART_LCR */ + 6, /* UART_MCR */ + -1, /* UART_LSR (unmapped) */ + -1, /* UART_MSR (unmapped) */ + -1, /* UART_SCR (unmapped) */ +}; + +static unsigned int au_serial_in(struct uart_port *p, int offset) +{ + if (offset >= ARRAY_SIZE(au_io_in_map)) + return UINT_MAX; + offset = au_io_in_map[offset]; + if (offset < 0) + return UINT_MAX; + return __raw_readl(p->membase + (offset << p->regshift)); +} + +static void au_serial_out(struct uart_port *p, int offset, int value) +{ + if (offset >= ARRAY_SIZE(au_io_out_map)) + return; + offset = au_io_out_map[offset]; + if (offset < 0) + return; + __raw_writel(value, p->membase + (offset << p->regshift)); +} + +/* Au1x00 haven't got a standard divisor latch */ +static int au_serial_dl_read(struct uart_8250_port *up) +{ + return __raw_readl(up->port.membase + 0x28); +} + +static void au_serial_dl_write(struct uart_8250_port *up, int value) +{ + __raw_writel(value, up->port.membase + 0x28); +} + +#endif + +static unsigned int hub6_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + outb(p->hub6 - 1 + offset, p->iobase); + return inb(p->iobase + 1); +} + +static void hub6_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + outb(p->hub6 - 1 + offset, p->iobase); + outb(value, p->iobase + 1); +} + +static unsigned int mem_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return readb(p->membase + offset); +} + +static void mem_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + writeb(value, p->membase + offset); +} + +static void mem32_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + writel(value, p->membase + offset); +} + +static unsigned int mem32_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return readl(p->membase + offset); +} + +static void mem32be_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + iowrite32be(value, p->membase + offset); +} + +static unsigned int mem32be_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return ioread32be(p->membase + offset); +} + +static unsigned int io_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return inb(p->iobase + offset); +} + +static void io_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + outb(value, p->iobase + offset); +} + +static int serial8250_default_handle_irq(struct uart_port *port); +static int exar_handle_irq(struct uart_port *port); + +static void set_io_from_upio(struct uart_port *p) +{ + struct uart_8250_port *up = up_to_u8250p(p); + + up->dl_read = default_serial_dl_read; + up->dl_write = default_serial_dl_write; + + switch (p->iotype) { + case UPIO_HUB6: + p->serial_in = hub6_serial_in; + p->serial_out = hub6_serial_out; + break; + + case UPIO_MEM: + p->serial_in = mem_serial_in; + p->serial_out = mem_serial_out; + break; + + case UPIO_MEM32: + p->serial_in = mem32_serial_in; + p->serial_out = mem32_serial_out; + break; + + case UPIO_MEM32BE: + p->serial_in = mem32be_serial_in; + p->serial_out = mem32be_serial_out; + break; + +#ifdef CONFIG_SERIAL_8250_RT288X + case UPIO_AU: + p->serial_in = au_serial_in; + p->serial_out = au_serial_out; + up->dl_read = au_serial_dl_read; + up->dl_write = au_serial_dl_write; + break; +#endif + + default: + p->serial_in = io_serial_in; + p->serial_out = io_serial_out; + break; + } + /* Remember loaded iotype */ + up->cur_iotype = p->iotype; + p->handle_irq = serial8250_default_handle_irq; +} + +static void +serial_port_out_sync(struct uart_port *p, int offset, int value) +{ + switch (p->iotype) { + case UPIO_MEM: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_AU: + p->serial_out(p, offset, value); + p->serial_in(p, UART_LCR); /* safe, no side-effects */ + break; + default: + p->serial_out(p, offset, value); + } +} + +/* + * For the 16C950 + */ +static void serial_icr_write(struct uart_8250_port *up, int offset, int value) +{ + serial_out(up, UART_SCR, offset); + serial_out(up, UART_ICR, value); +} + +static unsigned int serial_icr_read(struct uart_8250_port *up, int offset) +{ + unsigned int value; + + serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD); + serial_out(up, UART_SCR, offset); + value = serial_in(up, UART_ICR); + serial_icr_write(up, UART_ACR, up->acr); + + return value; +} + +/* + * FIFO support. + */ +static void serial8250_clear_fifos(struct uart_8250_port *p) +{ + if (p->capabilities & UART_CAP_FIFO) { + serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_out(p, UART_FCR, 0); + } +} + +void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p) +{ + serial8250_clear_fifos(p); + serial_out(p, UART_FCR, p->fcr); +} +EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos); + +void serial8250_rpm_get(struct uart_8250_port *p) +{ + if (!(p->capabilities & UART_CAP_RPM)) + return; + pm_runtime_get_sync(p->port.dev); +} +EXPORT_SYMBOL_GPL(serial8250_rpm_get); + +void serial8250_rpm_put(struct uart_8250_port *p) +{ + if (!(p->capabilities & UART_CAP_RPM)) + return; + pm_runtime_mark_last_busy(p->port.dev); + pm_runtime_put_autosuspend(p->port.dev); +} +EXPORT_SYMBOL_GPL(serial8250_rpm_put); + +/* + * These two wrappers ensure that enable_runtime_pm_tx() can be called more than + * once and disable_runtime_pm_tx() will still disable RPM because the fifo is + * empty and the HW can idle again. + */ +static void serial8250_rpm_get_tx(struct uart_8250_port *p) +{ + unsigned char rpm_active; + + if (!(p->capabilities & UART_CAP_RPM)) + return; + + rpm_active = xchg(&p->rpm_tx_active, 1); + if (rpm_active) + return; + pm_runtime_get_sync(p->port.dev); +} + +static void serial8250_rpm_put_tx(struct uart_8250_port *p) +{ + unsigned char rpm_active; + + if (!(p->capabilities & UART_CAP_RPM)) + return; + + rpm_active = xchg(&p->rpm_tx_active, 0); + if (!rpm_active) + return; + pm_runtime_mark_last_busy(p->port.dev); + pm_runtime_put_autosuspend(p->port.dev); +} + +/* + * IER sleep support. UARTs which have EFRs need the "extended + * capability" bit enabled. Note that on XR16C850s, we need to + * reset LCR to write to IER. + */ +static void serial8250_set_sleep(struct uart_8250_port *p, int sleep) +{ + unsigned char lcr = 0, efr = 0; + /* + * Exar UARTs have a SLEEP register that enables or disables + * each UART to enter sleep mode separately. On the XR17V35x the + * register is accessible to each UART at the UART_EXAR_SLEEP + * offset but the UART channel may only write to the corresponding + * bit. + */ + serial8250_rpm_get(p); + if ((p->port.type == PORT_XR17V35X) || + (p->port.type == PORT_XR17D15X)) { + serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0); + goto out; + } + + if (p->capabilities & UART_CAP_SLEEP) { + if (p->capabilities & UART_CAP_EFR) { + lcr = serial_in(p, UART_LCR); + efr = serial_in(p, UART_EFR); + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(p, UART_EFR, UART_EFR_ECB); + serial_out(p, UART_LCR, 0); + } + serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0); + if (p->capabilities & UART_CAP_EFR) { + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(p, UART_EFR, efr); + serial_out(p, UART_LCR, lcr); + } + } +out: + serial8250_rpm_put(p); +} + +#ifdef CONFIG_SERIAL_8250_RSA +/* + * Attempts to turn on the RSA FIFO. Returns zero on failure. + * We set the port uart clock rate if we succeed. + */ +static int __enable_rsa(struct uart_8250_port *up) +{ + unsigned char mode; + int result; + + mode = serial_in(up, UART_RSA_MSR); + result = mode & UART_RSA_MSR_FIFO; + + if (!result) { + serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO); + mode = serial_in(up, UART_RSA_MSR); + result = mode & UART_RSA_MSR_FIFO; + } + + if (result) + up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16; + + return result; +} + +static void enable_rsa(struct uart_8250_port *up) +{ + if (up->port.type == PORT_RSA) { + if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) { + spin_lock_irq(&up->port.lock); + __enable_rsa(up); + spin_unlock_irq(&up->port.lock); + } + if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) + serial_out(up, UART_RSA_FRR, 0); + } +} + +/* + * Attempts to turn off the RSA FIFO. Returns zero on failure. + * It is unknown why interrupts were disabled in here. However, + * the caller is expected to preserve this behaviour by grabbing + * the spinlock before calling this function. + */ +static void disable_rsa(struct uart_8250_port *up) +{ + unsigned char mode; + int result; + + if (up->port.type == PORT_RSA && + up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) { + spin_lock_irq(&up->port.lock); + + mode = serial_in(up, UART_RSA_MSR); + result = !(mode & UART_RSA_MSR_FIFO); + + if (!result) { + serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO); + mode = serial_in(up, UART_RSA_MSR); + result = !(mode & UART_RSA_MSR_FIFO); + } + + if (result) + up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16; + spin_unlock_irq(&up->port.lock); + } +} +#endif /* CONFIG_SERIAL_8250_RSA */ + +/* + * This is a quickie test to see how big the FIFO is. + * It doesn't work at all the time, more's the pity. + */ +static int size_fifo(struct uart_8250_port *up) +{ + unsigned char old_fcr, old_mcr, old_lcr; + unsigned short old_dl; + int count; + + old_lcr = serial_in(up, UART_LCR); + serial_out(up, UART_LCR, 0); + old_fcr = serial_in(up, UART_FCR); + old_mcr = serial_in(up, UART_MCR); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_out(up, UART_MCR, UART_MCR_LOOP); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + old_dl = serial_dl_read(up); + serial_dl_write(up, 0x0001); + serial_out(up, UART_LCR, 0x03); + for (count = 0; count < 256; count++) + serial_out(up, UART_TX, count); + mdelay(20);/* FIXME - schedule_timeout */ + for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) && + (count < 256); count++) + serial_in(up, UART_RX); + serial_out(up, UART_FCR, old_fcr); + serial_out(up, UART_MCR, old_mcr); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + serial_dl_write(up, old_dl); + serial_out(up, UART_LCR, old_lcr); + + return count; +} + +/* + * Read UART ID using the divisor method - set DLL and DLM to zero + * and the revision will be in DLL and device type in DLM. We + * preserve the device state across this. + */ +static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p) +{ + unsigned char old_dll, old_dlm, old_lcr; + unsigned int id; + + old_lcr = serial_in(p, UART_LCR); + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A); + + old_dll = serial_in(p, UART_DLL); + old_dlm = serial_in(p, UART_DLM); + + serial_out(p, UART_DLL, 0); + serial_out(p, UART_DLM, 0); + + id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8; + + serial_out(p, UART_DLL, old_dll); + serial_out(p, UART_DLM, old_dlm); + serial_out(p, UART_LCR, old_lcr); + + return id; +} + +/* + * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's. + * When this function is called we know it is at least a StarTech + * 16650 V2, but it might be one of several StarTech UARTs, or one of + * its clones. (We treat the broken original StarTech 16650 V1 as a + * 16550, and why not? Startech doesn't seem to even acknowledge its + * existence.) + * + * What evil have men's minds wrought... + */ +static void autoconfig_has_efr(struct uart_8250_port *up) +{ + unsigned int id1, id2, id3, rev; + + /* + * Everything with an EFR has SLEEP + */ + up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; + + /* + * First we check to see if it's an Oxford Semiconductor UART. + * + * If we have to do this here because some non-National + * Semiconductor clone chips lock up if you try writing to the + * LSR register (which serial_icr_read does) + */ + + /* + * Check for Oxford Semiconductor 16C950. + * + * EFR [4] must be set else this test fails. + * + * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca) + * claims that it's needed for 952 dual UART's (which are not + * recommended for new designs). + */ + up->acr = 0; + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, UART_LCR, 0x00); + id1 = serial_icr_read(up, UART_ID1); + id2 = serial_icr_read(up, UART_ID2); + id3 = serial_icr_read(up, UART_ID3); + rev = serial_icr_read(up, UART_REV); + + DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev); + + if (id1 == 0x16 && id2 == 0xC9 && + (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) { + up->port.type = PORT_16C950; + + /* + * Enable work around for the Oxford Semiconductor 952 rev B + * chip which causes it to seriously miscalculate baud rates + * when DLL is 0. + */ + if (id3 == 0x52 && rev == 0x01) + up->bugs |= UART_BUG_QUOT; + return; + } + + /* + * We check for a XR16C850 by setting DLL and DLM to 0, and then + * reading back DLL and DLM. The chip type depends on the DLM + * value read back: + * 0x10 - XR16C850 and the DLL contains the chip revision. + * 0x12 - XR16C2850. + * 0x14 - XR16C854. + */ + id1 = autoconfig_read_divisor_id(up); + DEBUG_AUTOCONF("850id=%04x ", id1); + + id2 = id1 >> 8; + if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) { + up->port.type = PORT_16850; + return; + } + + /* + * It wasn't an XR16C850. + * + * We distinguish between the '654 and the '650 by counting + * how many bytes are in the FIFO. I'm using this for now, + * since that's the technique that was sent to me in the + * serial driver update, but I'm not convinced this works. + * I've had problems doing this in the past. -TYT + */ + if (size_fifo(up) == 64) + up->port.type = PORT_16654; + else + up->port.type = PORT_16650V2; +} + +/* + * We detected a chip without a FIFO. Only two fall into + * this category - the original 8250 and the 16450. The + * 16450 has a scratch register (accessible with LCR=0) + */ +static void autoconfig_8250(struct uart_8250_port *up) +{ + unsigned char scratch, status1, status2; + + up->port.type = PORT_8250; + + scratch = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, 0xa5); + status1 = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, 0x5a); + status2 = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, scratch); + + if (status1 == 0xa5 && status2 == 0x5a) + up->port.type = PORT_16450; +} + +static int broken_efr(struct uart_8250_port *up) +{ + /* + * Exar ST16C2550 "A2" devices incorrectly detect as + * having an EFR, and report an ID of 0x0201. See + * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html + */ + if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16) + return 1; + + return 0; +} + +/* + * We know that the chip has FIFOs. Does it have an EFR? The + * EFR is located in the same register position as the IIR and + * we know the top two bits of the IIR are currently set. The + * EFR should contain zero. Try to read the EFR. + */ +static void autoconfig_16550a(struct uart_8250_port *up) +{ + unsigned char status1, status2; + unsigned int iersave; + + up->port.type = PORT_16550A; + up->capabilities |= UART_CAP_FIFO; + + /* + * XR17V35x UARTs have an extra divisor register, DLD + * that gets enabled with when DLAB is set which will + * cause the device to incorrectly match and assign + * port type to PORT_16650. The EFR for this UART is + * found at offset 0x09. Instead check the Deice ID (DVID) + * register for a 2, 4 or 8 port UART. + */ + if (up->port.flags & UPF_EXAR_EFR) { + status1 = serial_in(up, UART_EXAR_DVID); + if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) { + DEBUG_AUTOCONF("Exar XR17V35x "); + up->port.type = PORT_XR17V35X; + up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP; + + return; + } + + } + + /* + * Check for presence of the EFR when DLAB is set. + * Only ST16C650V1 UARTs pass this test. + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + if (serial_in(up, UART_EFR) == 0) { + serial_out(up, UART_EFR, 0xA8); + if (serial_in(up, UART_EFR) != 0) { + DEBUG_AUTOCONF("EFRv1 "); + up->port.type = PORT_16650; + up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; + } else { + serial_out(up, UART_LCR, 0); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR7_64BYTE); + status1 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, 0); + serial_out(up, UART_LCR, 0); + + if (status1 == 7) + up->port.type = PORT_16550A_FSL64; + else + DEBUG_AUTOCONF("Motorola 8xxx DUART "); + } + serial_out(up, UART_EFR, 0); + return; + } + + /* + * Maybe it requires 0xbf to be written to the LCR. + * (other ST16C650V2 UARTs, TI16C752A, etc) + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) { + DEBUG_AUTOCONF("EFRv2 "); + autoconfig_has_efr(up); + return; + } + + /* + * Check for a National Semiconductor SuperIO chip. + * Attempt to switch to bank 2, read the value of the LOOP bit + * from EXCR1. Switch back to bank 0, change it in MCR. Then + * switch back to bank 2, read it from EXCR1 again and check + * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2 + */ + serial_out(up, UART_LCR, 0); + status1 = serial_in(up, UART_MCR); + serial_out(up, UART_LCR, 0xE0); + status2 = serial_in(up, 0x02); /* EXCR1 */ + + if (!((status2 ^ status1) & UART_MCR_LOOP)) { + serial_out(up, UART_LCR, 0); + serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP); + serial_out(up, UART_LCR, 0xE0); + status2 = serial_in(up, 0x02); /* EXCR1 */ + serial_out(up, UART_LCR, 0); + serial_out(up, UART_MCR, status1); + + if ((status2 ^ status1) & UART_MCR_LOOP) { + unsigned short quot; + + serial_out(up, UART_LCR, 0xE0); + + quot = serial_dl_read(up); + quot <<= 3; + + if (ns16550a_goto_highspeed(up)) + serial_dl_write(up, quot); + + serial_out(up, UART_LCR, 0); + + up->port.uartclk = 921600*16; + up->port.type = PORT_NS16550A; + up->capabilities |= UART_NATSEMI; + return; + } + } + + /* + * No EFR. Try to detect a TI16750, which only sets bit 5 of + * the IIR when 64 byte FIFO mode is enabled when DLAB is set. + * Try setting it with and without DLAB set. Cheap clones + * set bit 5 without DLAB set. + */ + serial_out(up, UART_LCR, 0); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); + status1 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); + status2 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(up, UART_LCR, 0); + + DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2); + + if (status1 == 6 && status2 == 7) { + up->port.type = PORT_16750; + up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP; + return; + } + + /* + * Try writing and reading the UART_IER_UUE bit (b6). + * If it works, this is probably one of the Xscale platform's + * internal UARTs. + * We're going to explicitly set the UUE bit to 0 before + * trying to write and read a 1 just to make sure it's not + * already a 1 and maybe locked there before we even start start. + */ + iersave = serial_in(up, UART_IER); + serial_out(up, UART_IER, iersave & ~UART_IER_UUE); + if (!(serial_in(up, UART_IER) & UART_IER_UUE)) { + /* + * OK it's in a known zero state, try writing and reading + * without disturbing the current state of the other bits. + */ + serial_out(up, UART_IER, iersave | UART_IER_UUE); + if (serial_in(up, UART_IER) & UART_IER_UUE) { + /* + * It's an Xscale. + * We'll leave the UART_IER_UUE bit set to 1 (enabled). + */ + DEBUG_AUTOCONF("Xscale "); + up->port.type = PORT_XSCALE; + up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE; + return; + } + } else { + /* + * If we got here we couldn't force the IER_UUE bit to 0. + * Log it and continue. + */ + DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 "); + } + serial_out(up, UART_IER, iersave); + + /* + * Exar uarts have EFR in a weird location + */ + if (up->port.flags & UPF_EXAR_EFR) { + DEBUG_AUTOCONF("Exar XR17D15x "); + up->port.type = PORT_XR17D15X; + up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP; + + return; + } + + /* + * We distinguish between 16550A and U6 16550A by counting + * how many bytes are in the FIFO. + */ + if (up->port.type == PORT_16550A && size_fifo(up) == 64) { + up->port.type = PORT_U6_16550A; + up->capabilities |= UART_CAP_AFE; + } +} + +/* + * This routine is called by rs_init() to initialize a specific serial + * port. It determines what type of UART chip this serial port is + * using: 8250, 16450, 16550, 16550A. The important question is + * whether or not this UART is a 16550A or not, since this will + * determine whether or not we can use its FIFO features or not. + */ +static void autoconfig(struct uart_8250_port *up) +{ + unsigned char status1, scratch, scratch2, scratch3; + unsigned char save_lcr, save_mcr; + struct uart_port *port = &up->port; + unsigned long flags; + unsigned int old_capabilities; + + if (!port->iobase && !port->mapbase && !port->membase) + return; + + DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ", + serial_index(port), port->iobase, port->membase); + + /* + * We really do need global IRQs disabled here - we're going to + * be frobbing the chips IRQ enable register to see if it exists. + */ + spin_lock_irqsave(&port->lock, flags); + + up->capabilities = 0; + up->bugs = 0; + + if (!(port->flags & UPF_BUGGY_UART)) { + /* + * Do a simple existence test first; if we fail this, + * there's no point trying anything else. + * + * 0x80 is used as a nonsense port to prevent against + * false positives due to ISA bus float. The + * assumption is that 0x80 is a non-existent port; + * which should be safe since include/asm/io.h also + * makes this assumption. + * + * Note: this is safe as long as MCR bit 4 is clear + * and the device is in "PC" mode. + */ + scratch = serial_in(up, UART_IER); + serial_out(up, UART_IER, 0); +#ifdef __i386__ + outb(0xff, 0x080); +#endif + /* + * Mask out IER[7:4] bits for test as some UARTs (e.g. TL + * 16C754B) allow only to modify them if an EFR bit is set. + */ + scratch2 = serial_in(up, UART_IER) & 0x0f; + serial_out(up, UART_IER, 0x0F); +#ifdef __i386__ + outb(0, 0x080); +#endif + scratch3 = serial_in(up, UART_IER) & 0x0f; + serial_out(up, UART_IER, scratch); + if (scratch2 != 0 || scratch3 != 0x0F) { + /* + * We failed; there's nothing here + */ + spin_unlock_irqrestore(&port->lock, flags); + DEBUG_AUTOCONF("IER test failed (%02x, %02x) ", + scratch2, scratch3); + goto out; + } + } + + save_mcr = serial_in(up, UART_MCR); + save_lcr = serial_in(up, UART_LCR); + + /* + * Check to see if a UART is really there. Certain broken + * internal modems based on the Rockwell chipset fail this + * test, because they apparently don't implement the loopback + * test mode. So this test is skipped on the COM 1 through + * COM 4 ports. This *should* be safe, since no board + * manufacturer would be stupid enough to design a board + * that conflicts with COM 1-4 --- we hope! + */ + if (!(port->flags & UPF_SKIP_TEST)) { + serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A); + status1 = serial_in(up, UART_MSR) & 0xF0; + serial_out(up, UART_MCR, save_mcr); + if (status1 != 0x90) { + spin_unlock_irqrestore(&port->lock, flags); + DEBUG_AUTOCONF("LOOP test failed (%02x) ", + status1); + goto out; + } + } + + /* + * We're pretty sure there's a port here. Lets find out what + * type of port it is. The IIR top two bits allows us to find + * out if it's 8250 or 16450, 16550, 16550A or later. This + * determines what we test for next. + * + * We also initialise the EFR (if any) to zero for later. The + * EFR occupies the same register location as the FCR and IIR. + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(up, UART_EFR, 0); + serial_out(up, UART_LCR, 0); + + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + scratch = serial_in(up, UART_IIR) >> 6; + + switch (scratch) { + case 0: + autoconfig_8250(up); + break; + case 1: + port->type = PORT_UNKNOWN; + break; + case 2: + port->type = PORT_16550; + break; + case 3: + autoconfig_16550a(up); + break; + } + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * Only probe for RSA ports if we got the region. + */ + if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA && + __enable_rsa(up)) + port->type = PORT_RSA; +#endif + + serial_out(up, UART_LCR, save_lcr); + + port->fifosize = uart_config[up->port.type].fifo_size; + old_capabilities = up->capabilities; + up->capabilities = uart_config[port->type].flags; + up->tx_loadsz = uart_config[port->type].tx_loadsz; + + if (port->type == PORT_UNKNOWN) + goto out_lock; + + /* + * Reset the UART. + */ +#ifdef CONFIG_SERIAL_8250_RSA + if (port->type == PORT_RSA) + serial_out(up, UART_RSA_FRR, 0); +#endif + serial_out(up, UART_MCR, save_mcr); + serial8250_clear_fifos(up); + serial_in(up, UART_RX); + if (up->capabilities & UART_CAP_UUE) + serial_out(up, UART_IER, UART_IER_UUE); + else + serial_out(up, UART_IER, 0); + +out_lock: + spin_unlock_irqrestore(&port->lock, flags); + if (up->capabilities != old_capabilities) { + printk(KERN_WARNING + "ttyS%d: detected caps %08x should be %08x\n", + serial_index(port), old_capabilities, + up->capabilities); + } +out: + DEBUG_AUTOCONF("iir=%d ", scratch); + DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name); +} + +static void autoconfig_irq(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + unsigned char save_mcr, save_ier; + unsigned char save_ICP = 0; + unsigned int ICP = 0; + unsigned long irqs; + int irq; + + if (port->flags & UPF_FOURPORT) { + ICP = (port->iobase & 0xfe0) | 0x1f; + save_ICP = inb_p(ICP); + outb_p(0x80, ICP); + inb_p(ICP); + } + + if (uart_console(port)) + console_lock(); + + /* forget possible initially masked and pending IRQ */ + probe_irq_off(probe_irq_on()); + save_mcr = serial_in(up, UART_MCR); + save_ier = serial_in(up, UART_IER); + serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2); + + irqs = probe_irq_on(); + serial_out(up, UART_MCR, 0); + udelay(10); + if (port->flags & UPF_FOURPORT) { + serial_out(up, UART_MCR, + UART_MCR_DTR | UART_MCR_RTS); + } else { + serial_out(up, UART_MCR, + UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2); + } + serial_out(up, UART_IER, 0x0f); /* enable all intrs */ + serial_in(up, UART_LSR); + serial_in(up, UART_RX); + serial_in(up, UART_IIR); + serial_in(up, UART_MSR); + serial_out(up, UART_TX, 0xFF); + udelay(20); + irq = probe_irq_off(irqs); + + serial_out(up, UART_MCR, save_mcr); + serial_out(up, UART_IER, save_ier); + + if (port->flags & UPF_FOURPORT) + outb_p(save_ICP, ICP); + + if (uart_console(port)) + console_unlock(); + + port->irq = (irq > 0) ? irq : 0; +} + +static inline void __stop_tx(struct uart_8250_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + serial_out(p, UART_IER, p->ier); + serial8250_rpm_put_tx(p); + } +} + +static void serial8250_stop_tx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + __stop_tx(up); + + /* + * We really want to stop the transmitter from sending. + */ + if (port->type == PORT_16C950) { + up->acr |= UART_ACR_TXDIS; + serial_icr_write(up, UART_ACR, up->acr); + } + serial8250_rpm_put(up); +} + +static void serial8250_start_tx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get_tx(up); + + if (up->dma && !up->dma->tx_dma(up)) + return; + + if (!(up->ier & UART_IER_THRI)) { + up->ier |= UART_IER_THRI; + serial_port_out(port, UART_IER, up->ier); + + if (up->bugs & UART_BUG_TXEN) { + unsigned char lsr; + lsr = serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + if (lsr & UART_LSR_THRE) + serial8250_tx_chars(up); + } + } + + /* + * Re-enable the transmitter if we disabled it. + */ + if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) { + up->acr &= ~UART_ACR_TXDIS; + serial_icr_write(up, UART_ACR, up->acr); + } +} + +static void serial8250_throttle(struct uart_port *port) +{ + port->throttle(port); +} + +static void serial8250_unthrottle(struct uart_port *port) +{ + port->unthrottle(port); +} + +static void serial8250_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + + up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); + up->port.read_status_mask &= ~UART_LSR_DR; + serial_port_out(port, UART_IER, up->ier); + + serial8250_rpm_put(up); +} + +static void serial8250_disable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); + + /* no MSR capabilities */ + if (up->bugs & UART_BUG_NOMSR) + return; + + up->ier &= ~UART_IER_MSI; + serial_port_out(port, UART_IER, up->ier); +} + +static void serial8250_enable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + /* no MSR capabilities */ + if (up->bugs & UART_BUG_NOMSR) + return; + + up->ier |= UART_IER_MSI; + + serial8250_rpm_get(up); + serial_port_out(port, UART_IER, up->ier); + serial8250_rpm_put(up); +} + +/* + * serial8250_rx_chars: processes according to the passed in LSR + * value, and returns the remaining LSR bits not handled + * by this Rx routine. + */ +unsigned char +serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr) +{ + struct uart_port *port = &up->port; + unsigned char ch; + int max_count = 256; + char flag; + + do { + if (likely(lsr & UART_LSR_DR)) + ch = serial_in(up, UART_RX); + else + /* + * Intel 82571 has a Serial Over Lan device that will + * set UART_LSR_BI without setting UART_LSR_DR when + * it receives a break. To avoid reading from the + * receive buffer without UART_LSR_DR bit set, we + * just force the read character to be 0 + */ + ch = 0; + + flag = TTY_NORMAL; + port->icount.rx++; + + lsr |= up->lsr_saved_flags; + up->lsr_saved_flags = 0; + + if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) { + if (lsr & UART_LSR_BI) { + lsr &= ~(UART_LSR_FE | UART_LSR_PE); + port->icount.brk++; + /* + * We do the SysRQ and SAK checking + * here because otherwise the break + * may get masked by ignore_status_mask + * or read_status_mask. + */ + if (uart_handle_break(port)) + goto ignore_char; + } else if (lsr & UART_LSR_PE) + port->icount.parity++; + else if (lsr & UART_LSR_FE) + port->icount.frame++; + if (lsr & UART_LSR_OE) + port->icount.overrun++; + + /* + * Mask off conditions which should be ignored. + */ + lsr &= port->read_status_mask; + + if (lsr & UART_LSR_BI) { + DEBUG_INTR("handling break...."); + flag = TTY_BREAK; + } else if (lsr & UART_LSR_PE) + flag = TTY_PARITY; + else if (lsr & UART_LSR_FE) + flag = TTY_FRAME; + } + if (uart_handle_sysrq_char(port, ch)) + goto ignore_char; + + uart_insert_char(port, lsr, UART_LSR_OE, ch, flag); + +ignore_char: + lsr = serial_in(up, UART_LSR); + } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0)); + spin_unlock(&port->lock); + tty_flip_buffer_push(&port->state->port); + spin_lock(&port->lock); + return lsr; +} +EXPORT_SYMBOL_GPL(serial8250_rx_chars); + +void serial8250_tx_chars(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + struct circ_buf *xmit = &port->state->xmit; + int count; + + if (port->x_char) { + serial_out(up, UART_TX, port->x_char); + port->icount.tx++; + port->x_char = 0; + return; + } + if (uart_tx_stopped(port)) { + serial8250_stop_tx(port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->tx_loadsz; + do { + serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + if (uart_circ_empty(xmit)) + break; + if (up->capabilities & UART_CAP_HFIFO) { + if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) != + BOTH_EMPTY) + break; + } + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + DEBUG_INTR("THRE..."); + + /* + * With RPM enabled, we have to wait until the FIFO is empty before the + * HW can go idle. So we get here once again with empty FIFO and disable + * the interrupt and RPM in __stop_tx() + */ + if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM)) + __stop_tx(up); +} +EXPORT_SYMBOL_GPL(serial8250_tx_chars); + +/* Caller holds uart port lock */ +unsigned int serial8250_modem_status(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + unsigned int status = serial_in(up, UART_MSR); + + status |= up->msr_saved_flags; + up->msr_saved_flags = 0; + if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI && + port->state != NULL) { + if (status & UART_MSR_TERI) + port->icount.rng++; + if (status & UART_MSR_DDSR) + port->icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(port, status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(port, status & UART_MSR_CTS); + + wake_up_interruptible(&port->state->port.delta_msr_wait); + } + + return status; +} +EXPORT_SYMBOL_GPL(serial8250_modem_status); + +/* + * This handles the interrupt from one port. + */ +int serial8250_handle_irq(struct uart_port *port, unsigned int iir) +{ + unsigned char status; + unsigned long flags; + struct uart_8250_port *up = up_to_u8250p(port); + int dma_err = 0; + + if (iir & UART_IIR_NO_INT) + return 0; + + spin_lock_irqsave(&port->lock, flags); + + status = serial_port_in(port, UART_LSR); + + DEBUG_INTR("status = %x...", status); + + if (status & (UART_LSR_DR | UART_LSR_BI)) { + if (up->dma) + dma_err = up->dma->rx_dma(up, iir); + + if (!up->dma || dma_err) + status = serial8250_rx_chars(up, status); + } + serial8250_modem_status(up); + if ((!up->dma || (up->dma && up->dma->tx_err)) && + (status & UART_LSR_THRE)) + serial8250_tx_chars(up); + + spin_unlock_irqrestore(&port->lock, flags); + return 1; +} +EXPORT_SYMBOL_GPL(serial8250_handle_irq); + +static int serial8250_default_handle_irq(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned int iir; + int ret; + + serial8250_rpm_get(up); + + iir = serial_port_in(port, UART_IIR); + ret = serial8250_handle_irq(port, iir); + + serial8250_rpm_put(up); + return ret; +} + +/* + * These Exar UARTs have an extra interrupt indicator that could + * fire for a few unimplemented interrupts. One of which is a + * wakeup event when coming out of sleep. Put this here just + * to be on the safe side that these interrupts don't go unhandled. + */ +static int exar_handle_irq(struct uart_port *port) +{ + unsigned char int0, int1, int2, int3; + unsigned int iir = serial_port_in(port, UART_IIR); + int ret; + + ret = serial8250_handle_irq(port, iir); + + if ((port->type == PORT_XR17V35X) || + (port->type == PORT_XR17D15X)) { + int0 = serial_port_in(port, 0x80); + int1 = serial_port_in(port, 0x81); + int2 = serial_port_in(port, 0x82); + int3 = serial_port_in(port, 0x83); + } + + return ret; +} + +static unsigned int serial8250_tx_empty(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + unsigned int lsr; + + serial8250_rpm_get(up); + + spin_lock_irqsave(&port->lock, flags); + lsr = serial_port_in(port, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + spin_unlock_irqrestore(&port->lock, flags); + + serial8250_rpm_put(up); + + return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0; +} + +static unsigned int serial8250_get_mctrl(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned int status; + unsigned int ret; + + serial8250_rpm_get(up); + status = serial8250_modem_status(up); + serial8250_rpm_put(up); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char mcr = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; + + serial_port_out(port, UART_MCR, mcr); +} +EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl); + +static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + if (port->set_mctrl) + port->set_mctrl(port, mctrl); + else + serial8250_do_set_mctrl(port, mctrl); +} + +static void serial8250_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + + serial8250_rpm_get(up); + spin_lock_irqsave(&port->lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + serial_port_out(port, UART_LCR, up->lcr); + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); +} + +/* + * Wait for transmitter & holding register to empty + */ +static void wait_for_xmitr(struct uart_8250_port *up, int bits) +{ + unsigned int status, tmout = 10000; + + /* Wait up to 10ms for the character(s) to be sent. */ + for (;;) { + status = serial_in(up, UART_LSR); + + up->lsr_saved_flags |= status & LSR_SAVE_FLAGS; + + if ((status & bits) == bits) + break; + if (--tmout == 0) + break; + udelay(1); + } + + /* Wait up to 1s for flow control if necessary */ + if (up->port.flags & UPF_CONS_FLOW) { + unsigned int tmout; + for (tmout = 1000000; tmout; tmout--) { + unsigned int msr = serial_in(up, UART_MSR); + up->msr_saved_flags |= msr & MSR_SAVE_FLAGS; + if (msr & UART_MSR_CTS) + break; + udelay(1); + touch_nmi_watchdog(); + } + } +} + +#ifdef CONFIG_CONSOLE_POLL +/* + * Console polling routines for writing and reading from the uart while + * in an interrupt or debug context. + */ + +static int serial8250_get_poll_char(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char lsr; + int status; + + serial8250_rpm_get(up); + + lsr = serial_port_in(port, UART_LSR); + + if (!(lsr & UART_LSR_DR)) { + status = NO_POLL_CHAR; + goto out; + } + + status = serial_port_in(port, UART_RX); +out: + serial8250_rpm_put(up); + return status; +} + + +static void serial8250_put_poll_char(struct uart_port *port, + unsigned char c) +{ + unsigned int ier; + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + /* + * First save the IER then disable the interrupts + */ + ier = serial_port_in(port, UART_IER); + if (up->capabilities & UART_CAP_UUE) + serial_port_out(port, UART_IER, UART_IER_UUE); + else + serial_port_out(port, UART_IER, 0); + + wait_for_xmitr(up, BOTH_EMPTY); + /* + * Send the character out. + */ + serial_port_out(port, UART_TX, c); + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up, BOTH_EMPTY); + serial_port_out(port, UART_IER, ier); + serial8250_rpm_put(up); +} + +#endif /* CONFIG_CONSOLE_POLL */ + +int serial8250_do_startup(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + unsigned char lsr, iir; + int retval; + + if (!port->fifosize) + port->fifosize = uart_config[port->type].fifo_size; + if (!up->tx_loadsz) + up->tx_loadsz = uart_config[port->type].tx_loadsz; + if (!up->capabilities) + up->capabilities = uart_config[port->type].flags; + up->mcr = 0; + + if (port->iotype != up->cur_iotype) + set_io_from_upio(port); + + serial8250_rpm_get(up); + if (port->type == PORT_16C950) { + /* Wake up and initialize UART */ + up->acr = 0; + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + serial_port_out(port, UART_EFR, UART_EFR_ECB); + serial_port_out(port, UART_IER, 0); + serial_port_out(port, UART_LCR, 0); + serial_icr_write(up, UART_CSR, 0); /* Reset the UART */ + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + serial_port_out(port, UART_EFR, UART_EFR_ECB); + serial_port_out(port, UART_LCR, 0); + } + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * If this is an RSA port, see if we can kick it up to the + * higher speed clock. + */ + enable_rsa(up); +#endif + + if (port->type == PORT_XR17V35X) { + /* + * First enable access to IER [7:5], ISR [5:4], FCR [5:4], + * MCR [7:5] and MSR [7:0] + */ + serial_port_out(port, UART_XR_EFR, UART_EFR_ECB); + + /* + * Make sure all interrups are masked until initialization is + * complete and the FIFOs are cleared + */ + serial_port_out(port, UART_IER, 0); + } + + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + serial8250_clear_fifos(up); + + /* + * Clear the interrupt registers. + */ + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); + serial_port_in(port, UART_IIR); + serial_port_in(port, UART_MSR); + + /* + * At this point, there's no way the LSR could still be 0xff; + * if it is, then bail out, because there's likely no UART + * here. + */ + if (!(port->flags & UPF_BUGGY_UART) && + (serial_port_in(port, UART_LSR) == 0xff)) { + printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n", + serial_index(port)); + retval = -ENODEV; + goto out; + } + + /* + * For a XR16C850, we need to set the trigger levels + */ + if (port->type == PORT_16850) { + unsigned char fctr; + + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + + fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX); + serial_port_out(port, UART_FCTR, + fctr | UART_FCTR_TRGD | UART_FCTR_RX); + serial_port_out(port, UART_TRG, UART_TRG_96); + serial_port_out(port, UART_FCTR, + fctr | UART_FCTR_TRGD | UART_FCTR_TX); + serial_port_out(port, UART_TRG, UART_TRG_96); + + serial_port_out(port, UART_LCR, 0); + } + + if (port->irq) { + unsigned char iir1; + /* + * Test for UARTs that do not reassert THRE when the + * transmitter is idle and the interrupt has already + * been cleared. Real 16550s should always reassert + * this interrupt whenever the transmitter is idle and + * the interrupt is enabled. Delays are necessary to + * allow register changes to become visible. + */ + spin_lock_irqsave(&port->lock, flags); + if (up->port.irqflags & IRQF_SHARED) + disable_irq_nosync(port->irq); + + wait_for_xmitr(up, UART_LSR_THRE); + serial_port_out_sync(port, UART_IER, UART_IER_THRI); + udelay(1); /* allow THRE to set */ + iir1 = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + serial_port_out_sync(port, UART_IER, UART_IER_THRI); + udelay(1); /* allow a working UART time to re-assert THRE */ + iir = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + + if (port->irqflags & IRQF_SHARED) + enable_irq(port->irq); + spin_unlock_irqrestore(&port->lock, flags); + + /* + * If the interrupt is not reasserted, or we otherwise + * don't trust the iir, setup a timer to kick the UART + * on a regular basis. + */ + if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) || + up->port.flags & UPF_BUG_THRE) { + up->bugs |= UART_BUG_THRE; + } + } + + retval = up->ops->setup_irq(up); + if (retval) + goto out; + + /* + * Now, initialize the UART + */ + serial_port_out(port, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&port->lock, flags); + if (up->port.flags & UPF_FOURPORT) { + if (!up->port.irq) + up->port.mctrl |= TIOCM_OUT1; + } else + /* + * Most PC uarts need OUT2 raised to enable interrupts. + */ + if (port->irq) + up->port.mctrl |= TIOCM_OUT2; + + serial8250_set_mctrl(port, port->mctrl); + + /* Serial over Lan (SoL) hack: + Intel 8257x Gigabit ethernet chips have a + 16550 emulation, to be used for Serial Over Lan. + Those chips take a longer time than a normal + serial device to signalize that a transmission + data was queued. Due to that, the above test generally + fails. One solution would be to delay the reading of + iir. However, this is not reliable, since the timeout + is variable. So, let's just don't test if we receive + TX irq. This way, we'll never enable UART_BUG_TXEN. + */ + if (up->port.flags & UPF_NO_TXEN_TEST) + goto dont_test_tx_en; + + /* + * Do a quick test to see if we receive an + * interrupt when we enable the TX irq. + */ + serial_port_out(port, UART_IER, UART_IER_THRI); + lsr = serial_port_in(port, UART_LSR); + iir = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + + if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { + if (!(up->bugs & UART_BUG_TXEN)) { + up->bugs |= UART_BUG_TXEN; + pr_debug("ttyS%d - enabling bad tx status workarounds\n", + serial_index(port)); + } + } else { + up->bugs &= ~UART_BUG_TXEN; + } + +dont_test_tx_en: + spin_unlock_irqrestore(&port->lock, flags); + + /* + * Clear the interrupt registers again for luck, and clear the + * saved flags to avoid getting false values from polling + * routines or the previous session. + */ + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); + serial_port_in(port, UART_IIR); + serial_port_in(port, UART_MSR); + up->lsr_saved_flags = 0; + up->msr_saved_flags = 0; + + /* + * Request DMA channels for both RX and TX. + */ + if (up->dma) { + retval = serial8250_request_dma(up); + if (retval) { + pr_warn_ratelimited("ttyS%d - failed to request DMA\n", + serial_index(port)); + up->dma = NULL; + } + } + + /* + * Set the IER shadow for rx interrupts but defer actual interrupt + * enable until after the FIFOs are enabled; otherwise, an already- + * active sender can swamp the interrupt handler with "too much work". + */ + up->ier = UART_IER_RLSI | UART_IER_RDI; + + if (port->flags & UPF_FOURPORT) { + unsigned int icp; + /* + * Enable interrupts on the AST Fourport board + */ + icp = (port->iobase & 0xfe0) | 0x01f; + outb_p(0x80, icp); + inb_p(icp); + } + retval = 0; +out: + serial8250_rpm_put(up); + return retval; +} +EXPORT_SYMBOL_GPL(serial8250_do_startup); + +static int serial8250_startup(struct uart_port *port) +{ + if (port->startup) + return port->startup(port); + return serial8250_do_startup(port); +} + +void serial8250_do_shutdown(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + + serial8250_rpm_get(up); + /* + * Disable interrupts from this port + */ + up->ier = 0; + serial_port_out(port, UART_IER, 0); + + if (up->dma) + serial8250_release_dma(up); + + spin_lock_irqsave(&port->lock, flags); + if (port->flags & UPF_FOURPORT) { + /* reset interrupts on the AST Fourport board */ + inb((port->iobase & 0xfe0) | 0x1f); + port->mctrl |= TIOCM_OUT1; + } else + port->mctrl &= ~TIOCM_OUT2; + + serial8250_set_mctrl(port, port->mctrl); + spin_unlock_irqrestore(&port->lock, flags); + + /* + * Disable break condition and FIFOs + */ + serial_port_out(port, UART_LCR, + serial_port_in(port, UART_LCR) & ~UART_LCR_SBC); + serial8250_clear_fifos(up); + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * Reset the RSA board back to 115kbps compat mode. + */ + disable_rsa(up); +#endif + + /* + * Read data port to reset things, and then unlink from + * the IRQ chain. + */ + serial_port_in(port, UART_RX); + serial8250_rpm_put(up); + + up->ops->release_irq(up); +} +EXPORT_SYMBOL_GPL(serial8250_do_shutdown); + +static void serial8250_shutdown(struct uart_port *port) +{ + if (port->shutdown) + port->shutdown(port); + else + serial8250_do_shutdown(port); +} + +/* + * XR17V35x UARTs have an extra fractional divisor register (DLD) + * Calculate divisor with extra 4-bit fractional portion + */ +static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up, + unsigned int baud, + unsigned int *frac) +{ + struct uart_port *port = &up->port; + unsigned int quot_16; + + quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud); + *frac = quot_16 & 0x0f; + + return quot_16 >> 4; +} + +static unsigned int serial8250_get_divisor(struct uart_8250_port *up, + unsigned int baud, + unsigned int *frac) +{ + struct uart_port *port = &up->port; + unsigned int quot; + + /* + * Handle magic divisors for baud rates above baud_base on + * SMSC SuperIO chips. + * + */ + if ((port->flags & UPF_MAGIC_MULTIPLIER) && + baud == (port->uartclk/4)) + quot = 0x8001; + else if ((port->flags & UPF_MAGIC_MULTIPLIER) && + baud == (port->uartclk/8)) + quot = 0x8002; + else if (up->port.type == PORT_XR17V35X) + quot = xr17v35x_get_divisor(up, baud, frac); + else + quot = uart_get_divisor(port, baud); + + /* + * Oxford Semi 952 rev B workaround + */ + if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0) + quot++; + + return quot; +} + +static unsigned char serial8250_compute_lcr(struct uart_8250_port *up, + tcflag_t c_cflag) +{ + unsigned char cval; + + switch (c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + if (c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (c_cflag & PARENB) { + cval |= UART_LCR_PARITY; + if (up->bugs & UART_BUG_PARITY) + up->fifo_bug = true; + } + if (!(c_cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (c_cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + return cval; +} + +static void serial8250_set_divisor(struct uart_port *port, unsigned int baud, + unsigned int quot, unsigned int quot_frac) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + /* Workaround to enable 115200 baud on OMAP1510 internal ports */ + if (is_omap1510_8250(up)) { + if (baud == 115200) { + quot = 1; + serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1); + } else + serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0); + } + + /* + * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2, + * otherwise just set DLAB + */ + if (up->capabilities & UART_NATSEMI) + serial_port_out(port, UART_LCR, 0xe0); + else + serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB); + + serial_dl_write(up, quot); + + /* XR17V35x UARTs have an extra fractional divisor register (DLD) */ + if (up->port.type == PORT_XR17V35X) + serial_port_out(port, 0x2, quot_frac); +} + +static unsigned int +serial8250_get_baud_rate(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + unsigned int tolerance = port->uartclk / 100; + + /* + * Ask the core to calculate the divisor for us. + * Allow 1% tolerance at the upper limit so uart clks marginally + * slower than nominal still match standard baud rates without + * causing transmission errors. + */ + return uart_get_baud_rate(port, termios, old, + port->uartclk / 16 / 0xffff, + (port->uartclk + tolerance) / 16); +} + +void +serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char cval; + unsigned long flags; + unsigned int baud, quot, frac = 0; + + cval = serial8250_compute_lcr(up, termios->c_cflag); + + baud = serial8250_get_baud_rate(port, termios, old); + quot = serial8250_get_divisor(up, baud, &frac); + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + serial8250_rpm_get(up); + spin_lock_irqsave(&port->lock, flags); + + up->lcr = cval; /* Save computed LCR */ + + if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) { + /* NOTE: If fifo_bug is not set, a user can set RX_trigger. */ + if ((baud < 2400 && !up->dma) || up->fifo_bug) { + up->fcr &= ~UART_FCR_TRIGGER_MASK; + up->fcr |= UART_FCR_TRIGGER_1; + } + } + + /* + * MCR-based auto flow control. When AFE is enabled, RTS will be + * deasserted when the receive FIFO contains more characters than + * the trigger, or the MCR RTS bit is cleared. In the case where + * the remote UART is not using CTS auto flow control, we must + * have sufficient FIFO entries for the latency of the remote + * UART to respond. IOW, at least 32 bytes of FIFO. + */ + if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) { + up->mcr &= ~UART_MCR_AFE; + if (termios->c_cflag & CRTSCTS) + up->mcr |= UART_MCR_AFE; + } + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + port->read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) + port->read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + port->ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + port->ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (!(up->bugs & UART_BUG_NOMSR) && + UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + if (up->capabilities & UART_CAP_UUE) + up->ier |= UART_IER_UUE; + if (up->capabilities & UART_CAP_RTOIE) + up->ier |= UART_IER_RTOIE; + + serial_port_out(port, UART_IER, up->ier); + + if (up->capabilities & UART_CAP_EFR) { + unsigned char efr = 0; + /* + * TI16C752/Startech hardware flow control. FIXME: + * - TI16C752 requires control thresholds to be set. + * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled. + */ + if (termios->c_cflag & CRTSCTS) + efr |= UART_EFR_CTS; + + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + if (port->flags & UPF_EXAR_EFR) + serial_port_out(port, UART_XR_EFR, efr); + else + serial_port_out(port, UART_EFR, efr); + } + + serial8250_set_divisor(port, baud, quot, frac); + + /* + * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR + * is written without DLAB set, this mode will be disabled. + */ + if (port->type == PORT_16750) + serial_port_out(port, UART_FCR, up->fcr); + + serial_port_out(port, UART_LCR, up->lcr); /* reset DLAB */ + if (port->type != PORT_16750) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + if (up->fcr & UART_FCR_ENABLE_FIFO) + serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_port_out(port, UART_FCR, up->fcr); /* set fcr */ + } + serial8250_set_mctrl(port, port->mctrl); + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); + + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} +EXPORT_SYMBOL(serial8250_do_set_termios); + +static void +serial8250_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + if (port->set_termios) + port->set_termios(port, termios, old); + else + serial8250_do_set_termios(port, termios, old); +} + +static void +serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios) +{ + if (termios->c_line == N_PPS) { + port->flags |= UPF_HARDPPS_CD; + spin_lock_irq(&port->lock); + serial8250_enable_ms(port); + spin_unlock_irq(&port->lock); + } else { + port->flags &= ~UPF_HARDPPS_CD; + if (!UART_ENABLE_MS(port, termios->c_cflag)) { + spin_lock_irq(&port->lock); + serial8250_disable_ms(port); + spin_unlock_irq(&port->lock); + } + } +} + + +void serial8250_do_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ + struct uart_8250_port *p = up_to_u8250p(port); + + serial8250_set_sleep(p, state != 0); +} +EXPORT_SYMBOL(serial8250_do_pm); + +static void +serial8250_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ + if (port->pm) + port->pm(port, state, oldstate); + else + serial8250_do_pm(port, state, oldstate); +} + +static unsigned int serial8250_port_size(struct uart_8250_port *pt) +{ + if (pt->port.mapsize) + return pt->port.mapsize; + if (pt->port.iotype == UPIO_AU) { + if (pt->port.type == PORT_RT2880) + return 0x100; + return 0x1000; + } + if (is_omap1_8250(pt)) + return 0x16 << pt->port.regshift; + + return 8 << pt->port.regshift; +} + +/* + * Resource handling. + */ +static int serial8250_request_std_resource(struct uart_8250_port *up) +{ + unsigned int size = serial8250_port_size(up); + struct uart_port *port = &up->port; + int ret = 0; + + switch (port->iotype) { + case UPIO_AU: + case UPIO_TSI: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_MEM: + if (!port->mapbase) + break; + + if (!request_mem_region(port->mapbase, size, "serial")) { + ret = -EBUSY; + break; + } + + if (port->flags & UPF_IOREMAP) { + port->membase = ioremap_nocache(port->mapbase, size); + if (!port->membase) { + release_mem_region(port->mapbase, size); + ret = -ENOMEM; + } + } + break; + + case UPIO_HUB6: + case UPIO_PORT: + if (!request_region(port->iobase, size, "serial")) + ret = -EBUSY; + break; + } + return ret; +} + +static void serial8250_release_std_resource(struct uart_8250_port *up) +{ + unsigned int size = serial8250_port_size(up); + struct uart_port *port = &up->port; + + switch (port->iotype) { + case UPIO_AU: + case UPIO_TSI: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_MEM: + if (!port->mapbase) + break; + + if (port->flags & UPF_IOREMAP) { + iounmap(port->membase); + port->membase = NULL; + } + + release_mem_region(port->mapbase, size); + break; + + case UPIO_HUB6: + case UPIO_PORT: + release_region(port->iobase, size); + break; + } +} + +static void serial8250_release_port(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_release_std_resource(up); +} + +static int serial8250_request_port(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + return serial8250_request_std_resource(up); +} + +static int fcr_get_rxtrig_bytes(struct uart_8250_port *up) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + unsigned char bytes; + + bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)]; + + return bytes ? bytes : -EOPNOTSUPP; +} + +static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + int i; + + if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)]) + return -EOPNOTSUPP; + + for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) { + if (bytes < conf_type->rxtrig_bytes[i]) + /* Use the nearest lower value */ + return (--i) << UART_FCR_R_TRIG_SHIFT; + } + + return UART_FCR_R_TRIG_11; +} + +static int do_get_rxtrig(struct tty_port *port) +{ + struct uart_state *state = container_of(port, struct uart_state, port); + struct uart_port *uport = state->uart_port; + struct uart_8250_port *up = + container_of(uport, struct uart_8250_port, port); + + if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1) + return -EINVAL; + + return fcr_get_rxtrig_bytes(up); +} + +static int do_serial8250_get_rxtrig(struct tty_port *port) +{ + int rxtrig_bytes; + + mutex_lock(&port->mutex); + rxtrig_bytes = do_get_rxtrig(port); + mutex_unlock(&port->mutex); + + return rxtrig_bytes; +} + +static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct tty_port *port = dev_get_drvdata(dev); + int rxtrig_bytes; + + rxtrig_bytes = do_serial8250_get_rxtrig(port); + if (rxtrig_bytes < 0) + return rxtrig_bytes; + + return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes); +} + +static int do_set_rxtrig(struct tty_port *port, unsigned char bytes) +{ + struct uart_state *state = container_of(port, struct uart_state, port); + struct uart_port *uport = state->uart_port; + struct uart_8250_port *up = + container_of(uport, struct uart_8250_port, port); + int rxtrig; + + if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 || + up->fifo_bug) + return -EINVAL; + + rxtrig = bytes_to_fcr_rxtrig(up, bytes); + if (rxtrig < 0) + return rxtrig; + + serial8250_clear_fifos(up); + up->fcr &= ~UART_FCR_TRIGGER_MASK; + up->fcr |= (unsigned char)rxtrig; + serial_out(up, UART_FCR, up->fcr); + return 0; +} + +static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes) +{ + int ret; + + mutex_lock(&port->mutex); + ret = do_set_rxtrig(port, bytes); + mutex_unlock(&port->mutex); + + return ret; +} + +static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev, + struct device_attribute *attr, const char *buf, size_t count) +{ + struct tty_port *port = dev_get_drvdata(dev); + unsigned char bytes; + int ret; + + if (!count) + return -EINVAL; + + ret = kstrtou8(buf, 10, &bytes); + if (ret < 0) + return ret; + + ret = do_serial8250_set_rxtrig(port, bytes); + if (ret < 0) + return ret; + + return count; +} + +static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP, + serial8250_get_attr_rx_trig_bytes, + serial8250_set_attr_rx_trig_bytes); + +static struct attribute *serial8250_dev_attrs[] = { + &dev_attr_rx_trig_bytes.attr, + NULL, + }; + +static struct attribute_group serial8250_dev_attr_group = { + .attrs = serial8250_dev_attrs, + }; + +static void register_dev_spec_attr_grp(struct uart_8250_port *up) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + + if (conf_type->rxtrig_bytes[0]) + up->port.attr_group = &serial8250_dev_attr_group; +} + +static void serial8250_config_port(struct uart_port *port, int flags) +{ + struct uart_8250_port *up = up_to_u8250p(port); + int ret; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = serial8250_request_std_resource(up); + if (ret < 0) + return; + + if (port->iotype != up->cur_iotype) + set_io_from_upio(port); + + if (flags & UART_CONFIG_TYPE) + autoconfig(up); + + /* if access method is AU, it is a 16550 with a quirk */ + if (port->type == PORT_16550A && port->iotype == UPIO_AU) + up->bugs |= UART_BUG_NOMSR; + + /* HW bugs may trigger IRQ while IIR == NO_INT */ + if (port->type == PORT_TEGRA) + up->bugs |= UART_BUG_NOMSR; + + if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ) + autoconfig_irq(up); + + if (port->type == PORT_UNKNOWN) + serial8250_release_std_resource(up); + + /* Fixme: probably not the best place for this */ + if ((port->type == PORT_XR17V35X) || + (port->type == PORT_XR17D15X)) + port->handle_irq = exar_handle_irq; + + register_dev_spec_attr_grp(up); + up->fcr = uart_config[up->port.type].fcr; +} + +static int +serial8250_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + if (ser->irq >= nr_irqs || ser->irq < 0 || + ser->baud_base < 9600 || ser->type < PORT_UNKNOWN || + ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS || + ser->type == PORT_STARTECH) + return -EINVAL; + return 0; +} + +static const char * +serial8250_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + +static const struct uart_ops serial8250_pops = { + .tx_empty = serial8250_tx_empty, + .set_mctrl = serial8250_set_mctrl, + .get_mctrl = serial8250_get_mctrl, + .stop_tx = serial8250_stop_tx, + .start_tx = serial8250_start_tx, + .throttle = serial8250_throttle, + .unthrottle = serial8250_unthrottle, + .stop_rx = serial8250_stop_rx, + .enable_ms = serial8250_enable_ms, + .break_ctl = serial8250_break_ctl, + .startup = serial8250_startup, + .shutdown = serial8250_shutdown, + .set_termios = serial8250_set_termios, + .set_ldisc = serial8250_set_ldisc, + .pm = serial8250_pm, + .type = serial8250_type, + .release_port = serial8250_release_port, + .request_port = serial8250_request_port, + .config_port = serial8250_config_port, + .verify_port = serial8250_verify_port, +#ifdef CONFIG_CONSOLE_POLL + .poll_get_char = serial8250_get_poll_char, + .poll_put_char = serial8250_put_poll_char, +#endif +}; + +void serial8250_init_port(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + + spin_lock_init(&port->lock); + port->ops = &serial8250_pops; + + up->cur_iotype = 0xFF; +} +EXPORT_SYMBOL_GPL(serial8250_init_port); + +void serial8250_set_defaults(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + + if (up->port.flags & UPF_FIXED_TYPE) { + unsigned int type = up->port.type; + + if (!up->port.fifosize) + up->port.fifosize = uart_config[type].fifo_size; + if (!up->tx_loadsz) + up->tx_loadsz = uart_config[type].tx_loadsz; + if (!up->capabilities) + up->capabilities = uart_config[type].flags; + } + + set_io_from_upio(port); + + /* default dma handlers */ + if (up->dma) { + if (!up->dma->tx_dma) + up->dma->tx_dma = serial8250_tx_dma; + if (!up->dma->rx_dma) + up->dma->rx_dma = serial8250_rx_dma; + } +} +EXPORT_SYMBOL_GPL(serial8250_set_defaults); + +#ifdef CONFIG_SERIAL_8250_CONSOLE + +static void serial8250_console_putchar(struct uart_port *port, int ch) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + wait_for_xmitr(up, UART_LSR_THRE); + serial_port_out(port, UART_TX, ch); +} + +/* + * Restore serial console when h/w power-off detected + */ +static void serial8250_console_restore(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + struct ktermios termios; + unsigned int baud, quot, frac = 0; + + termios.c_cflag = port->cons->cflag; + if (port->state->port.tty && termios.c_cflag == 0) + termios.c_cflag = port->state->port.tty->termios.c_cflag; + + baud = serial8250_get_baud_rate(port, &termios, NULL); + quot = serial8250_get_divisor(up, baud, &frac); + + serial8250_set_divisor(port, baud, quot, frac); + serial_port_out(port, UART_LCR, up->lcr); + serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS); +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + * + * The console_lock must be held when we get here. + */ +void serial8250_console_write(struct uart_8250_port *up, const char *s, + unsigned int count) +{ + struct uart_port *port = &up->port; + unsigned long flags; + unsigned int ier; + int locked = 1; + + touch_nmi_watchdog(); + + serial8250_rpm_get(up); + + if (port->sysrq) + locked = 0; + else if (oops_in_progress || in_kdb_printk()) + locked = spin_trylock_irqsave(&port->lock, flags); + else + spin_lock_irqsave(&port->lock, flags); + + /* + * First save the IER then disable the interrupts + */ + ier = serial_port_in(port, UART_IER); + + if (up->capabilities & UART_CAP_UUE) + serial_port_out(port, UART_IER, UART_IER_UUE); + else + serial_port_out(port, UART_IER, 0); + + /* check scratch reg to see if port powered off during system sleep */ + if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) { + serial8250_console_restore(up); + up->canary = 0; + } + + uart_console_write(port, s, count, serial8250_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up, BOTH_EMPTY); + serial_port_out(port, UART_IER, ier); + + /* + * The receive handling will happen properly because the + * receive ready bit will still be set; it is not cleared + * on read. However, modem control will not, we must + * call it if we have saved something in the saved flags + * while processing with interrupts off. + */ + if (up->msr_saved_flags) + serial8250_modem_status(up); + + if (locked) + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); +} + +static unsigned int probe_baud(struct uart_port *port) +{ + unsigned char lcr, dll, dlm; + unsigned int quot; + + lcr = serial_port_in(port, UART_LCR); + serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB); + dll = serial_port_in(port, UART_DLL); + dlm = serial_port_in(port, UART_DLM); + serial_port_out(port, UART_LCR, lcr); + + quot = (dlm << 8) | dll; + return (port->uartclk / 16) / quot; +} + +int serial8250_console_setup(struct uart_port *port, char *options, bool probe) +{ + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if (!port->iobase && !port->membase) + return -ENODEV; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + else if (probe) + baud = probe_baud(port); + + return uart_set_options(port, port->cons, baud, parity, bits, flow); +} + +#endif /* CONFIG_SERIAL_8250_CONSOLE */ + +MODULE_LICENSE("GPL"); diff --git a/kernel/drivers/tty/serial/8250/8250_uniphier.c b/kernel/drivers/tty/serial/8250/8250_uniphier.c new file mode 100644 index 000000000..245edbb68 --- /dev/null +++ b/kernel/drivers/tty/serial/8250/8250_uniphier.c @@ -0,0 +1,262 @@ +/* + * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include "8250.h" + +/* Most (but not all) of UniPhier UART devices have 64-depth FIFO. */ +#define UNIPHIER_UART_DEFAULT_FIFO_SIZE 64 + +#define UNIPHIER_UART_CHAR_FCR 3 /* Character / FIFO Control Register */ +#define UNIPHIER_UART_LCR_MCR 4 /* Line/Modem Control Register */ +#define UNIPHIER_UART_LCR_SHIFT 8 +#define UNIPHIER_UART_DLR 9 /* Divisor Latch Register */ + +struct uniphier8250_priv { + int line; + struct clk *clk; + spinlock_t atomic_write_lock; +}; + +/* + * The register map is slightly different from that of 8250. + * IO callbacks must be overridden for correct access to FCR, LCR, and MCR. + */ +static unsigned int uniphier_serial_in(struct uart_port *p, int offset) +{ + unsigned int valshift = 0; + + switch (offset) { + case UART_LCR: + valshift = UNIPHIER_UART_LCR_SHIFT; + /* fall through */ + case UART_MCR: + offset = UNIPHIER_UART_LCR_MCR; + break; + default: + break; + } + + offset <<= p->regshift; + + /* + * The return value must be masked with 0xff because LCR and MCR reside + * in the same register that must be accessed by 32-bit write/read. + * 8 or 16 bit access to this hardware result in unexpected behavior. + */ + return (readl(p->membase + offset) >> valshift) & 0xff; +} + +static void uniphier_serial_out(struct uart_port *p, int offset, int value) +{ + unsigned int valshift = 0; + bool normal = false; + + switch (offset) { + case UART_FCR: + offset = UNIPHIER_UART_CHAR_FCR; + break; + case UART_LCR: + valshift = UNIPHIER_UART_LCR_SHIFT; + /* Divisor latch access bit does not exist. */ + value &= ~(UART_LCR_DLAB << valshift); + /* fall through */ + case UART_MCR: + offset = UNIPHIER_UART_LCR_MCR; + break; + default: + normal = true; + break; + } + + offset <<= p->regshift; + + if (normal) { + writel(value, p->membase + offset); + } else { + /* + * Special case: two registers share the same address that + * must be 32-bit accessed. As this is not longer atomic safe, + * take a lock just in case. + */ + struct uniphier8250_priv *priv = p->private_data; + unsigned long flags; + u32 tmp; + + spin_lock_irqsave(&priv->atomic_write_lock, flags); + tmp = readl(p->membase + offset); + tmp &= ~(0xff << valshift); + tmp |= value << valshift; + writel(tmp, p->membase + offset); + spin_unlock_irqrestore(&priv->atomic_write_lock, flags); + } +} + +/* + * This hardware does not have the divisor latch access bit. + * The divisor latch register exists at different address. + * Override dl_read/write callbacks. + */ +static int uniphier_serial_dl_read(struct uart_8250_port *up) +{ + int offset = UNIPHIER_UART_DLR << up->port.regshift; + + return readl(up->port.membase + offset); +} + +static void uniphier_serial_dl_write(struct uart_8250_port *up, int value) +{ + int offset = UNIPHIER_UART_DLR << up->port.regshift; + + writel(value, up->port.membase + offset); +} + +static int uniphier_of_serial_setup(struct device *dev, struct uart_port *port, + struct uniphier8250_priv *priv) +{ + int ret; + u32 prop; + struct device_node *np = dev->of_node; + + ret = of_alias_get_id(np, "serial"); + if (ret < 0) { + dev_err(dev, "failed to get alias id\n"); + return ret; + } + port->line = priv->line = ret; + + /* Get clk rate through clk driver */ + priv->clk = devm_clk_get(dev, NULL); + if (IS_ERR(priv->clk)) { + dev_err(dev, "failed to get clock\n"); + return PTR_ERR(priv->clk); + } + + ret = clk_prepare_enable(priv->clk); + if (ret < 0) + return ret; + + port->uartclk = clk_get_rate(priv->clk); + + /* Check for fifo size */ + if (of_property_read_u32(np, "fifo-size", &prop) == 0) + port->fifosize = prop; + else + port->fifosize = UNIPHIER_UART_DEFAULT_FIFO_SIZE; + + return 0; +} + +static int uniphier_uart_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct uart_8250_port up; + struct uniphier8250_priv *priv; + struct resource *regs; + void __iomem *membase; + int irq; + int ret; + + regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!regs) { + dev_err(dev, "failed to get memory resource"); + return -EINVAL; + } + + membase = devm_ioremap(dev, regs->start, resource_size(regs)); + if (!membase) + return -ENOMEM; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "failed to get IRQ number"); + return irq; + } + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + memset(&up, 0, sizeof(up)); + + ret = uniphier_of_serial_setup(dev, &up.port, priv); + if (ret < 0) + return ret; + + spin_lock_init(&priv->atomic_write_lock); + + up.port.dev = dev; + up.port.private_data = priv; + up.port.mapbase = regs->start; + up.port.mapsize = resource_size(regs); + up.port.membase = membase; + up.port.irq = irq; + + up.port.type = PORT_16550A; + up.port.iotype = UPIO_MEM32; + up.port.regshift = 2; + up.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE; + up.capabilities = UART_CAP_FIFO; + + up.port.serial_in = uniphier_serial_in; + up.port.serial_out = uniphier_serial_out; + up.dl_read = uniphier_serial_dl_read; + up.dl_write = uniphier_serial_dl_write; + + ret = serial8250_register_8250_port(&up); + if (ret < 0) { + dev_err(dev, "failed to register 8250 port\n"); + clk_disable_unprepare(priv->clk); + return ret; + } + + platform_set_drvdata(pdev, priv); + + return 0; +} + +static int uniphier_uart_remove(struct platform_device *pdev) +{ + struct uniphier8250_priv *priv = platform_get_drvdata(pdev); + + serial8250_unregister_port(priv->line); + clk_disable_unprepare(priv->clk); + + return 0; +} + +static const struct of_device_id uniphier_uart_match[] = { + { .compatible = "socionext,uniphier-uart" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, uniphier_uart_match); + +static struct platform_driver uniphier_uart_platform_driver = { + .probe = uniphier_uart_probe, + .remove = uniphier_uart_remove, + .driver = { + .name = "uniphier-uart", + .of_match_table = uniphier_uart_match, + }, +}; +module_platform_driver(uniphier_uart_platform_driver); + +MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>"); +MODULE_DESCRIPTION("UniPhier UART driver"); +MODULE_LICENSE("GPL"); diff --git a/kernel/drivers/tty/serial/8250/Kconfig b/kernel/drivers/tty/serial/8250/Kconfig index c35070356..6412f1455 100644 --- a/kernel/drivers/tty/serial/8250/Kconfig +++ b/kernel/drivers/tty/serial/8250/Kconfig @@ -274,8 +274,8 @@ config SERIAL_8250_ACORN config SERIAL_8250_FSL bool - depends on SERIAL_8250_CONSOLE && PPC_UDBG_16550 - default PPC + depends on SERIAL_8250_CONSOLE + default PPC || ARM || ARM64 config SERIAL_8250_DW tristate "Support for Synopsys DesignWare 8250 quirks" @@ -294,11 +294,12 @@ config SERIAL_8250_EM config SERIAL_8250_RT288X bool "Ralink RT288x/RT305x/RT3662/RT3883 serial port support" - depends on SERIAL_8250 && (SOC_RT288X || SOC_RT305X || SOC_RT3883 || SOC_MT7620) + depends on SERIAL_8250 + default y if MIPS_ALCHEMY || SOC_RT288X || SOC_RT305X || SOC_RT3883 || SOC_MT7620 help - If you have a Ralink RT288x/RT305x SoC based board and want to use the - serial port, say Y to this option. The driver can handle up to 2 serial - ports. If unsure, say N. + Selecting this option will add support for the alternate register + layout used by Ralink RT288x/RT305x, Alchemy Au1xxx, and some others. + If unsure, say N. config SERIAL_8250_OMAP tristate "Support for OMAP internal UART (8250 based driver)" @@ -336,9 +337,44 @@ config SERIAL_8250_FINTEK LPC to 4 UART. This device has some RS485 functionality not available through the PNP driver. If unsure, say N. +config SERIAL_8250_LPC18XX + tristate "NXP LPC18xx/43xx serial port support" + depends on SERIAL_8250 && OF && (ARCH_LPC18XX || COMPILE_TEST) + default ARCH_LPC18XX + help + If you have a LPC18xx/43xx based board and want to use the + serial port, say Y to this option. If unsure, say Y. + config SERIAL_8250_MT6577 bool "Mediatek serial port support" depends on SERIAL_8250 && ARCH_MEDIATEK help If you have a Mediatek based board and want to use the serial port, say Y to this option. If unsure, say N. + +config SERIAL_8250_UNIPHIER + tristate "Support for UniPhier on-chip UART" + depends on SERIAL_8250 && ARCH_UNIPHIER + help + If you have a UniPhier based board and want to use the on-chip + serial ports, say Y to this option. If unsure, say N. + +config SERIAL_8250_INGENIC + bool "Support for Ingenic SoC serial ports" + depends on SERIAL_8250_CONSOLE && OF_FLATTREE + select LIBFDT + select SERIAL_EARLYCON + help + If you have a system using an Ingenic SoC and wish to make use of + its UARTs, say Y to this option. If unsure, say N. + +config SERIAL_8250_MID + tristate "Support for serial ports on Intel MID platforms" + depends on SERIAL_8250 && PCI + select HSU_DMA if SERIAL_8250_DMA + select HSU_DMA_PCI if X86_INTEL_MID + select RATIONAL + help + Selecting this option will enable handling of the extra features + present on the UART found on Intel Medfield SOC and various other + Intel platforms. diff --git a/kernel/drivers/tty/serial/8250/Makefile b/kernel/drivers/tty/serial/8250/Makefile index 31e7cdc68..e177f8681 100644 --- a/kernel/drivers/tty/serial/8250/Makefile +++ b/kernel/drivers/tty/serial/8250/Makefile @@ -2,10 +2,11 @@ # Makefile for the 8250 serial device drivers. # -obj-$(CONFIG_SERIAL_8250) += 8250.o +obj-$(CONFIG_SERIAL_8250) += 8250.o 8250_base.o 8250-y := 8250_core.o 8250-$(CONFIG_SERIAL_8250_PNP) += 8250_pnp.o -8250-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o +8250_base-y := 8250_port.o +8250_base-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o @@ -22,4 +23,10 @@ obj-$(CONFIG_SERIAL_8250_DW) += 8250_dw.o obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o obj-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o +obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o +obj-$(CONFIG_SERIAL_8250_UNIPHIER) += 8250_uniphier.o +obj-$(CONFIG_SERIAL_8250_INGENIC) += 8250_ingenic.o +obj-$(CONFIG_SERIAL_8250_MID) += 8250_mid.o + +CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt |