diff options
Diffstat (limited to 'kernel/drivers/thermal/ti-soc-thermal')
| -rw-r--r-- | kernel/drivers/thermal/ti-soc-thermal/Kconfig | 23 | ||||
| -rw-r--r-- | kernel/drivers/thermal/ti-soc-thermal/Makefile | 1 | ||||
| -rw-r--r-- | kernel/drivers/thermal/ti-soc-thermal/omap3-thermal-data.c | 176 | ||||
| -rw-r--r-- | kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.c | 118 | ||||
| -rw-r--r-- | kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.h | 11 | ||||
| -rw-r--r-- | kernel/drivers/thermal/ti-soc-thermal/ti-thermal-common.c | 15 |
6 files changed, 278 insertions, 66 deletions
diff --git a/kernel/drivers/thermal/ti-soc-thermal/Kconfig b/kernel/drivers/thermal/ti-soc-thermal/Kconfig index bd4c7beba..ea8283f08 100644 --- a/kernel/drivers/thermal/ti-soc-thermal/Kconfig +++ b/kernel/drivers/thermal/ti-soc-thermal/Kconfig @@ -1,7 +1,5 @@ config TI_SOC_THERMAL tristate "Texas Instruments SoCs temperature sensor driver" - depends on THERMAL - depends on ARCH_HAS_BANDGAP help If you say yes here you get support for the Texas Instruments OMAP4460+ on die bandgap temperature sensor support. The register @@ -21,10 +19,25 @@ config TI_THERMAL This includes trip points definitions, extrapolation rules and CPU cooling device bindings. +config OMAP3_THERMAL + bool "Texas Instruments OMAP3 thermal support" + depends on TI_SOC_THERMAL + depends on ARCH_OMAP3 || COMPILE_TEST + help + If you say yes here you get thermal support for the Texas Instruments + OMAP3 SoC family. The current chips supported are: + - OMAP3430 + + OMAP3 chips normally don't need thermal management, and sensors in + this generation are not accurate, nor they are very close to + the important hotspots. + + Say 'N' here. + config OMAP4_THERMAL bool "Texas Instruments OMAP4 thermal support" depends on TI_SOC_THERMAL - depends on ARCH_OMAP4 + depends on ARCH_OMAP4 || COMPILE_TEST help If you say yes here you get thermal support for the Texas Instruments OMAP4 SoC family. The current chip supported are: @@ -38,7 +51,7 @@ config OMAP4_THERMAL config OMAP5_THERMAL bool "Texas Instruments OMAP5 thermal support" depends on TI_SOC_THERMAL - depends on SOC_OMAP5 + depends on SOC_OMAP5 || COMPILE_TEST help If you say yes here you get thermal support for the Texas Instruments OMAP5 SoC family. The current chip supported are: @@ -50,7 +63,7 @@ config OMAP5_THERMAL config DRA752_THERMAL bool "Texas Instruments DRA752 thermal support" depends on TI_SOC_THERMAL - depends on SOC_DRA7XX + depends on SOC_DRA7XX || COMPILE_TEST help If you say yes here you get thermal support for the Texas Instruments DRA752 SoC family. The current chip supported are: diff --git a/kernel/drivers/thermal/ti-soc-thermal/Makefile b/kernel/drivers/thermal/ti-soc-thermal/Makefile index 1226b2484..0f89bdf03 100644 --- a/kernel/drivers/thermal/ti-soc-thermal/Makefile +++ b/kernel/drivers/thermal/ti-soc-thermal/Makefile @@ -2,5 +2,6 @@ obj-$(CONFIG_TI_SOC_THERMAL) += ti-soc-thermal.o ti-soc-thermal-y := ti-bandgap.o ti-soc-thermal-$(CONFIG_TI_THERMAL) += ti-thermal-common.o ti-soc-thermal-$(CONFIG_DRA752_THERMAL) += dra752-thermal-data.o +ti-soc-thermal-$(CONFIG_OMAP3_THERMAL) += omap3-thermal-data.o ti-soc-thermal-$(CONFIG_OMAP4_THERMAL) += omap4-thermal-data.o ti-soc-thermal-$(CONFIG_OMAP5_THERMAL) += omap5-thermal-data.o diff --git a/kernel/drivers/thermal/ti-soc-thermal/omap3-thermal-data.c b/kernel/drivers/thermal/ti-soc-thermal/omap3-thermal-data.c new file mode 100644 index 000000000..3ee34340e --- /dev/null +++ b/kernel/drivers/thermal/ti-soc-thermal/omap3-thermal-data.c @@ -0,0 +1,176 @@ +/* + * OMAP3 thermal driver. + * + * Copyright (C) 2011-2012 Texas Instruments Inc. + * Copyright (C) 2014 Pavel Machek <pavel@ucw.cz> + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Note + * http://www.ti.com/lit/er/sprz278f/sprz278f.pdf "Advisory + * 3.1.1.186 MMC OCP Clock Not Gated When Thermal Sensor Is Used" + * + * Also TI says: + * Just be careful when you try to make thermal policy like decisions + * based on this sensor. Placement of the sensor w.r.t the actual logic + * generating heat has to be a factor as well. If you are just looking + * for an approximation temperature (thermometerish kind), you might be + * ok with this. I am not sure we'd find any TI data around this.. just a + * heads up. + */ + +#include "ti-thermal.h" +#include "ti-bandgap.h" + +/* + * OMAP34XX has one instance of thermal sensor for MPU + * need to describe the individual bit fields + */ +static struct temp_sensor_registers +omap34xx_mpu_temp_sensor_registers = { + .temp_sensor_ctrl = 0, + .bgap_soc_mask = BIT(8), + .bgap_eocz_mask = BIT(7), + .bgap_dtemp_mask = 0x7f, + + .bgap_mode_ctrl = 0, + .mode_ctrl_mask = BIT(9), +}; + +/* Thresholds and limits for OMAP34XX MPU temperature sensor */ +static struct temp_sensor_data omap34xx_mpu_temp_sensor_data = { + .min_freq = 32768, + .max_freq = 32768, + .max_temp = 125000, + .min_temp = -40000, + .hyst_val = 5000, +}; + +/* + * Temperature values in milli degree celsius + */ +static const int +omap34xx_adc_to_temp[128] = { + -40000, -40000, -40000, -40000, -40000, -39000, -38000, -36000, + -34000, -32000, -31000, -29000, -28000, -26000, -25000, -24000, + -22000, -21000, -19000, -18000, -17000, -15000, -14000, -12000, + -11000, -9000, -8000, -7000, -5000, -4000, -2000, -1000, 0000, + 1000, 3000, 4000, 5000, 7000, 8000, 10000, 11000, 13000, 14000, + 15000, 17000, 18000, 20000, 21000, 22000, 24000, 25000, 27000, + 28000, 30000, 31000, 32000, 34000, 35000, 37000, 38000, 39000, + 41000, 42000, 44000, 45000, 47000, 48000, 49000, 51000, 52000, + 53000, 55000, 56000, 58000, 59000, 60000, 62000, 63000, 65000, + 66000, 67000, 69000, 70000, 72000, 73000, 74000, 76000, 77000, + 79000, 80000, 81000, 83000, 84000, 85000, 87000, 88000, 89000, + 91000, 92000, 94000, 95000, 96000, 98000, 99000, 100000, + 102000, 103000, 105000, 106000, 107000, 109000, 110000, 111000, + 113000, 114000, 116000, 117000, 118000, 120000, 121000, 122000, + 124000, 124000, 125000, 125000, 125000, 125000, 125000 +}; + +/* OMAP34XX data */ +const struct ti_bandgap_data omap34xx_data = { + .features = TI_BANDGAP_FEATURE_CLK_CTRL | TI_BANDGAP_FEATURE_UNRELIABLE, + .fclock_name = "ts_fck", + .div_ck_name = "ts_fck", + .conv_table = omap34xx_adc_to_temp, + .adc_start_val = 0, + .adc_end_val = 127, + .expose_sensor = ti_thermal_expose_sensor, + .remove_sensor = ti_thermal_remove_sensor, + + .sensors = { + { + .registers = &omap34xx_mpu_temp_sensor_registers, + .ts_data = &omap34xx_mpu_temp_sensor_data, + .domain = "cpu", + .slope = 0, + .constant = 20000, + .slope_pcb = 0, + .constant_pcb = 20000, + .register_cooling = NULL, + .unregister_cooling = NULL, + }, + }, + .sensor_count = 1, +}; + +/* + * OMAP36XX has one instance of thermal sensor for MPU + * need to describe the individual bit fields + */ +static struct temp_sensor_registers +omap36xx_mpu_temp_sensor_registers = { + .temp_sensor_ctrl = 0, + .bgap_soc_mask = BIT(9), + .bgap_eocz_mask = BIT(8), + .bgap_dtemp_mask = 0xFF, + + .bgap_mode_ctrl = 0, + .mode_ctrl_mask = BIT(10), +}; + +/* Thresholds and limits for OMAP36XX MPU temperature sensor */ +static struct temp_sensor_data omap36xx_mpu_temp_sensor_data = { + .min_freq = 32768, + .max_freq = 32768, + .max_temp = 125000, + .min_temp = -40000, + .hyst_val = 5000, +}; + +/* + * Temperature values in milli degree celsius + */ +static const int +omap36xx_adc_to_temp[128] = { + -40000, -40000, -40000, -40000, -40000, -40000, -40000, -40000, + -40000, -40000, -40000, -40000, -40000, -38000, -35000, -34000, + -32000, -30000, -28000, -26000, -24000, -22000, -20000, -18500, + -17000, -15000, -13500, -12000, -10000, -8000, -6500, -5000, -3500, + -1500, 0, 2000, 3500, 5000, 6500, 8500, 10000, 12000, 13500, + 15000, 17000, 19000, 21000, 23000, 25000, 27000, 28500, 30000, + 32000, 33500, 35000, 37000, 38500, 40000, 42000, 43500, 45000, + 47000, 48500, 50000, 52000, 53500, 55000, 57000, 58500, 60000, + 62000, 64000, 66000, 68000, 70000, 71500, 73500, 75000, 77000, + 78500, 80000, 82000, 83500, 85000, 87000, 88500, 90000, 92000, + 93500, 95000, 97000, 98500, 100000, 102000, 103500, 105000, 107000, + 109000, 111000, 113000, 115000, 117000, 118500, 120000, 122000, + 123500, 125000, 125000, 125000, 125000, 125000, 125000, 125000, + 125000, 125000, 125000, 125000, 125000, 125000, 125000, 125000, + 125000, 125000, 125000, 125000, 125000, 125000, 125000 +}; + +/* OMAP36XX data */ +const struct ti_bandgap_data omap36xx_data = { + .features = TI_BANDGAP_FEATURE_CLK_CTRL | TI_BANDGAP_FEATURE_UNRELIABLE, + .fclock_name = "ts_fck", + .div_ck_name = "ts_fck", + .conv_table = omap36xx_adc_to_temp, + .adc_start_val = 0, + .adc_end_val = 127, + .expose_sensor = ti_thermal_expose_sensor, + .remove_sensor = ti_thermal_remove_sensor, + + .sensors = { + { + .registers = &omap36xx_mpu_temp_sensor_registers, + .ts_data = &omap36xx_mpu_temp_sensor_data, + .domain = "cpu", + .slope = 0, + .constant = 20000, + .slope_pcb = 0, + .constant_pcb = 20000, + .register_cooling = NULL, + .unregister_cooling = NULL, + }, + }, + .sensor_count = 1, +}; diff --git a/kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.c index bc14dc874..1e34a1efc 100644 --- a/kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.c +++ b/kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.c @@ -43,6 +43,8 @@ #include "ti-bandgap.h" +static int ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id); + /*** Helper functions to access registers and their bitfields ***/ /** @@ -103,19 +105,15 @@ do { \ */ static int ti_bandgap_power(struct ti_bandgap *bgp, bool on) { - int i, ret = 0; + int i; - if (!TI_BANDGAP_HAS(bgp, POWER_SWITCH)) { - ret = -ENOTSUPP; - goto exit; - } + if (!TI_BANDGAP_HAS(bgp, POWER_SWITCH)) + return -ENOTSUPP; for (i = 0; i < bgp->conf->sensor_count; i++) /* active on 0 */ RMW_BITS(bgp, i, temp_sensor_ctrl, bgap_tempsoff_mask, !on); - -exit: - return ret; + return 0; } /** @@ -298,18 +296,13 @@ static int ti_bandgap_adc_to_mcelsius(struct ti_bandgap *bgp, int adc_val, int *t) { const struct ti_bandgap_data *conf = bgp->conf; - int ret = 0; /* look up for temperature in the table and return the temperature */ - if (adc_val < conf->adc_start_val || adc_val > conf->adc_end_val) { - ret = -ERANGE; - goto exit; - } + if (adc_val < conf->adc_start_val || adc_val > conf->adc_end_val) + return -ERANGE; *t = bgp->conf->conv_table[adc_val - conf->adc_start_val]; - -exit: - return ret; + return 0; } /** @@ -330,16 +323,14 @@ int ti_bandgap_mcelsius_to_adc(struct ti_bandgap *bgp, long temp, int *adc) { const struct ti_bandgap_data *conf = bgp->conf; const int *conv_table = bgp->conf->conv_table; - int high, low, mid, ret = 0; + int high, low, mid; low = 0; high = conf->adc_end_val - conf->adc_start_val; mid = (high + low) / 2; - if (temp < conv_table[low] || temp > conv_table[high]) { - ret = -ERANGE; - goto exit; - } + if (temp < conv_table[low] || temp > conv_table[high]) + return -ERANGE; while (low < high) { if (temp < conv_table[mid]) @@ -350,9 +341,7 @@ int ti_bandgap_mcelsius_to_adc(struct ti_bandgap *bgp, long temp, int *adc) } *adc = conf->adc_start_val + low; - -exit: - return ret; + return 0; } /** @@ -378,13 +367,11 @@ int ti_bandgap_add_hyst(struct ti_bandgap *bgp, int adc_val, int hyst_val, */ ret = ti_bandgap_adc_to_mcelsius(bgp, adc_val, &temp); if (ret < 0) - goto exit; + return ret; temp += hyst_val; ret = ti_bandgap_mcelsius_to_adc(bgp, temp, sum); - -exit: return ret; } @@ -542,22 +529,18 @@ exit: */ static inline int ti_bandgap_validate(struct ti_bandgap *bgp, int id) { - int ret = 0; - if (!bgp || IS_ERR(bgp)) { pr_err("%s: invalid bandgap pointer\n", __func__); - ret = -EINVAL; - goto exit; + return -EINVAL; } if ((id < 0) || (id >= bgp->conf->sensor_count)) { dev_err(bgp->dev, "%s: sensor id out of range (%d)\n", __func__, id); - ret = -ERANGE; + return -ERANGE; } -exit: - return ret; + return 0; } /** @@ -585,12 +568,10 @@ static int _ti_bandgap_write_threshold(struct ti_bandgap *bgp, int id, int val, ret = ti_bandgap_validate(bgp, id); if (ret) - goto exit; + return ret; - if (!TI_BANDGAP_HAS(bgp, TALERT)) { - ret = -ENOTSUPP; - goto exit; - } + if (!TI_BANDGAP_HAS(bgp, TALERT)) + return -ENOTSUPP; ts_data = bgp->conf->sensors[id].ts_data; tsr = bgp->conf->sensors[id].registers; @@ -603,17 +584,15 @@ static int _ti_bandgap_write_threshold(struct ti_bandgap *bgp, int id, int val, } if (ret) - goto exit; + return ret; ret = ti_bandgap_mcelsius_to_adc(bgp, val, &adc_val); if (ret < 0) - goto exit; + return ret; spin_lock(&bgp->lock); ret = ti_bandgap_update_alert_threshold(bgp, id, adc_val, hot); spin_unlock(&bgp->lock); - -exit: return ret; } @@ -656,7 +635,7 @@ static int _ti_bandgap_read_threshold(struct ti_bandgap *bgp, int id, temp = ti_bandgap_readl(bgp, tsr->bgap_threshold); temp = (temp & mask) >> __ffs(mask); - ret |= ti_bandgap_adc_to_mcelsius(bgp, temp, &temp); + ret = ti_bandgap_adc_to_mcelsius(bgp, temp, &temp); if (ret) { dev_err(bgp->dev, "failed to read thot\n"); ret = -EIO; @@ -926,11 +905,17 @@ int ti_bandgap_read_temperature(struct ti_bandgap *bgp, int id, if (ret) return ret; + if (!TI_BANDGAP_HAS(bgp, MODE_CONFIG)) { + ret = ti_bandgap_force_single_read(bgp, id); + if (ret) + return ret; + } + spin_lock(&bgp->lock); temp = ti_bandgap_read_temp(bgp, id); spin_unlock(&bgp->lock); - ret |= ti_bandgap_adc_to_mcelsius(bgp, temp, &temp); + ret = ti_bandgap_adc_to_mcelsius(bgp, temp, &temp); if (ret) return -EIO; @@ -991,7 +976,8 @@ void *ti_bandgap_get_sensor_data(struct ti_bandgap *bgp, int id) static int ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id) { - u32 temp = 0, counter = 1000; + u32 counter = 1000; + struct temp_sensor_registers *tsr; /* Select single conversion mode */ if (TI_BANDGAP_HAS(bgp, MODE_CONFIG)) @@ -999,16 +985,27 @@ ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id) /* Start of Conversion = 1 */ RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 1); - /* Wait until DTEMP is updated */ - temp = ti_bandgap_read_temp(bgp, id); - while ((temp == 0) && --counter) - temp = ti_bandgap_read_temp(bgp, id); - /* REVISIT: Check correct condition for end of conversion */ + /* Wait for EOCZ going up */ + tsr = bgp->conf->sensors[id].registers; + + while (--counter) { + if (ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) & + tsr->bgap_eocz_mask) + break; + } /* Start of Conversion = 0 */ RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 0); + /* Wait for EOCZ going down */ + counter = 1000; + while (--counter) { + if (!(ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) & + tsr->bgap_eocz_mask)) + break; + } + return 0; } @@ -1277,6 +1274,10 @@ int ti_bandgap_probe(struct platform_device *pdev) } bgp->dev = &pdev->dev; + if (TI_BANDGAP_HAS(bgp, UNRELIABLE)) + dev_warn(&pdev->dev, + "This OMAP thermal sensor is unreliable. You've been warned\n"); + if (TI_BANDGAP_HAS(bgp, TSHUT)) { ret = ti_bandgap_tshut_init(bgp, pdev); if (ret) { @@ -1294,11 +1295,10 @@ int ti_bandgap_probe(struct platform_device *pdev) goto free_irqs; } - bgp->div_clk = clk_get(NULL, bgp->conf->div_ck_name); + bgp->div_clk = clk_get(NULL, bgp->conf->div_ck_name); ret = IS_ERR(bgp->div_clk); if (ret) { - dev_err(&pdev->dev, - "failed to request div_ts_ck clock ref\n"); + dev_err(&pdev->dev, "failed to request div_ts_ck clock ref\n"); ret = PTR_ERR(bgp->div_clk); goto free_irqs; } @@ -1583,6 +1583,16 @@ static SIMPLE_DEV_PM_OPS(ti_bandgap_dev_pm_ops, ti_bandgap_suspend, #endif static const struct of_device_id of_ti_bandgap_match[] = { +#ifdef CONFIG_OMAP3_THERMAL + { + .compatible = "ti,omap34xx-bandgap", + .data = (void *)&omap34xx_data, + }, + { + .compatible = "ti,omap36xx-bandgap", + .data = (void *)&omap36xx_data, + }, +#endif #ifdef CONFIG_OMAP4_THERMAL { .compatible = "ti,omap4430-bandgap", diff --git a/kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.h b/kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.h index 0c52f7afb..fe0adb898 100644 --- a/kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.h +++ b/kernel/drivers/thermal/ti-soc-thermal/ti-bandgap.h @@ -322,6 +322,8 @@ struct ti_temp_sensor { * has Errata 814 * TI_BANDGAP_FEATURE_ERRATA_813 - used to workaorund when the bandgap device * has Errata 813 + * TI_BANDGAP_FEATURE_UNRELIABLE - used when the sensor readings are too + * inaccurate. * TI_BANDGAP_HAS(b, f) - macro to check if a bandgap device is capable of a * specific feature (above) or not. Return non-zero, if yes. */ @@ -337,6 +339,7 @@ struct ti_temp_sensor { #define TI_BANDGAP_FEATURE_HISTORY_BUFFER BIT(9) #define TI_BANDGAP_FEATURE_ERRATA_814 BIT(10) #define TI_BANDGAP_FEATURE_ERRATA_813 BIT(11) +#define TI_BANDGAP_FEATURE_UNRELIABLE BIT(12) #define TI_BANDGAP_HAS(b, f) \ ((b)->conf->features & TI_BANDGAP_FEATURE_ ## f) @@ -390,6 +393,14 @@ int ti_bandgap_set_sensor_data(struct ti_bandgap *bgp, int id, void *data); void *ti_bandgap_get_sensor_data(struct ti_bandgap *bgp, int id); int ti_bandgap_get_trend(struct ti_bandgap *bgp, int id, int *trend); +#ifdef CONFIG_OMAP3_THERMAL +extern const struct ti_bandgap_data omap34xx_data; +extern const struct ti_bandgap_data omap36xx_data; +#else +#define omap34xx_data NULL +#define omap36xx_data NULL +#endif + #ifdef CONFIG_OMAP4_THERMAL extern const struct ti_bandgap_data omap4430_data; extern const struct ti_bandgap_data omap4460_data; diff --git a/kernel/drivers/thermal/ti-soc-thermal/ti-thermal-common.c b/kernel/drivers/thermal/ti-soc-thermal/ti-thermal-common.c index a38c17564..b213a1222 100644 --- a/kernel/drivers/thermal/ti-soc-thermal/ti-thermal-common.c +++ b/kernel/drivers/thermal/ti-soc-thermal/ti-thermal-common.c @@ -75,15 +75,15 @@ static inline int ti_thermal_hotspot_temperature(int t, int s, int c) } /* thermal zone ops */ -/* Get temperature callback function for thermal zone*/ -static inline int __ti_thermal_get_temp(void *devdata, long *temp) +/* Get temperature callback function for thermal zone */ +static inline int __ti_thermal_get_temp(void *devdata, int *temp) { struct thermal_zone_device *pcb_tz = NULL; struct ti_thermal_data *data = devdata; struct ti_bandgap *bgp; const struct ti_temp_sensor *s; int ret, tmp, slope, constant; - unsigned long pcb_temp; + int pcb_temp; if (!data) return 0; @@ -119,7 +119,7 @@ static inline int __ti_thermal_get_temp(void *devdata, long *temp) } static inline int ti_thermal_get_temp(struct thermal_zone_device *thermal, - unsigned long *temp) + int *temp) { struct ti_thermal_data *data = thermal->devdata; @@ -146,7 +146,8 @@ static int ti_thermal_bind(struct thermal_zone_device *thermal, return thermal_zone_bind_cooling_device(thermal, 0, cdev, /* bind with min and max states defined by cpu_cooling */ THERMAL_NO_LIMIT, - THERMAL_NO_LIMIT); + THERMAL_NO_LIMIT, + THERMAL_WEIGHT_DEFAULT); } /* Unbind callback functions for thermal zone */ @@ -228,7 +229,7 @@ static int ti_thermal_get_trip_type(struct thermal_zone_device *thermal, /* Get trip temperature callback functions for thermal zone */ static int ti_thermal_get_trip_temp(struct thermal_zone_device *thermal, - int trip, unsigned long *temp) + int trip, int *temp) { if (!ti_thermal_is_valid_trip(trip)) return -EINVAL; @@ -279,7 +280,7 @@ static int ti_thermal_get_trend(struct thermal_zone_device *thermal, /* Get critical temperature callback functions for thermal zone */ static int ti_thermal_get_crit_temp(struct thermal_zone_device *thermal, - unsigned long *temp) + int *temp) { /* shutdown zone */ return ti_thermal_get_trip_temp(thermal, OMAP_TRIP_NUMBER - 1, temp); |