1 files changed, 75 insertions, 0 deletions
diff --git a/kernel/drivers/staging/wilc1000/Kconfig b/kernel/drivers/staging/wilc1000/Kconfig
new file mode 100644
index 000000000..ee51b4278
--- /dev/null
+++ b/kernel/drivers/staging/wilc1000/Kconfig
@@ -0,0 +1,75 @@
+config WILC1000_DRIVER
+	bool "WILC1000 support (WiFi only)"
+	depends on CFG80211 && WEXT_CORE && INET
+	---help---
+	  This module only support IEEE 802.11n WiFi.
+
+if WILC1000_DRIVER
+
+config WILC1000
+	tristate
+
+choice
+        prompt "Memory Allocation"
+        default WILC1000_PREALLOCATE_AT_LOADING_DRIVER
+
+config WILC1000_PREALLOCATE_AT_LOADING_DRIVER
+	bool "Preallocate memory at loading driver"
+	---help---
+	  This choice supports static allocation of the memory
+	  for the receive buffer. The driver will allocate the RX buffer
+	  during initial time. The driver will also free the buffer
+	  by calling network device stop.
+
+config WILC1000_DYNAMICALLY_ALLOCATE_MEMROY
+        bool "Dynamically allocate memory in real time"
+        ---help---
+	  This choice supports dynamic allocation of the memory
+	  for the receive buffer. The driver will allocate the RX buffer
+	  when it is required.
+endchoice
+
+choice
+	prompt "Bus Type"
+	default WILC1000_SDIO
+
+config WILC1000_SDIO
+	bool "SDIO support"
+	depends on MMC
+	select WILC1000
+	---help---
+	  This module adds support for the SDIO interface of adapters using
+	  WILC1000 chipset. The Atmel WILC1000 SDIO is a full speed interface.
+	  It meets SDIO card specification version 2.0. The interface supports
+	  the 1-bit/4-bit SD transfer mode at the clock range of 0-50 MHz.
+	  The host can use this interface to read and write from any register
+	  within the chip as well as configure the WILC1000 for data DMA.
+	  To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
+	  this if your platform is using the SDIO bus.
+
+config WILC1000_SPI
+	depends on SPI
+	select WILC1000
+	bool "SPI support"
+	---help---
+	  This module adds support for the SPI interface of adapters using
+	  WILC1000 chipset. The Atmel WILC1000 has a Serial Peripheral
+	  Interface (SPI) that operates as a SPI slave. This SPI interface can
+	  be used for control and for serial I/O of 802.11 data. The SPI is a
+	  full-duplex slave synchronous serial interface that is available
+	  immediately following reset when pin 9 (SDIO_SPI_CFG) is tied to
+	  VDDIO. Select this if your platform is using the SPI bus.
+endchoice
+
+config WILC1000_HW_OOB_INTR
+	bool "Use out of band interrupt"
+	depends on WILC1000_SDIO
+	default n
+	---help---
+	  This option enables out-of-band interrupt support for the WILC1000
+	  chipset. This OOB interrupt is intended to provide a faster interrupt
+	  mechanism for SDIO host controllers that don't support SDIO interrupt.
+	  Select this option If the SDIO host controller in your platform
+	  doesn't support SDIO time devision interrupt.
+
+endif