diff options
Diffstat (limited to 'kernel/drivers/scsi/aic7xxx/aic7xxx_pci.c')
| -rw-r--r-- | kernel/drivers/scsi/aic7xxx/aic7xxx_pci.c | 2469 |
1 files changed, 2469 insertions, 0 deletions
diff --git a/kernel/drivers/scsi/aic7xxx/aic7xxx_pci.c b/kernel/drivers/scsi/aic7xxx/aic7xxx_pci.c new file mode 100644 index 000000000..22d5a949e --- /dev/null +++ b/kernel/drivers/scsi/aic7xxx/aic7xxx_pci.c @@ -0,0 +1,2469 @@ +/* + * Product specific probe and attach routines for: + * 3940, 2940, aic7895, aic7890, aic7880, + * aic7870, aic7860 and aic7850 SCSI controllers + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2001 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_pci.c#79 $ + */ + +#ifdef __linux__ +#include "aic7xxx_osm.h" +#include "aic7xxx_inline.h" +#include "aic7xxx_93cx6.h" +#else +#include <dev/aic7xxx/aic7xxx_osm.h> +#include <dev/aic7xxx/aic7xxx_inline.h> +#include <dev/aic7xxx/aic7xxx_93cx6.h> +#endif + +#include "aic7xxx_pci.h" + +static inline uint64_t +ahc_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor) +{ + uint64_t id; + + id = subvendor + | (subdevice << 16) + | ((uint64_t)vendor << 32) + | ((uint64_t)device << 48); + + return (id); +} + +#define AHC_PCI_IOADDR PCIR_MAPS /* I/O Address */ +#define AHC_PCI_MEMADDR (PCIR_MAPS + 4) /* Mem I/O Address */ + +#define DEVID_9005_TYPE(id) ((id) & 0xF) +#define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */ +#define DEVID_9005_TYPE_AAA 0x3 /* RAID Card */ +#define DEVID_9005_TYPE_SISL 0x5 /* Container ROMB */ +#define DEVID_9005_TYPE_MB 0xF /* On Motherboard */ + +#define DEVID_9005_MAXRATE(id) (((id) & 0x30) >> 4) +#define DEVID_9005_MAXRATE_U160 0x0 +#define DEVID_9005_MAXRATE_ULTRA2 0x1 +#define DEVID_9005_MAXRATE_ULTRA 0x2 +#define DEVID_9005_MAXRATE_FAST 0x3 + +#define DEVID_9005_MFUNC(id) (((id) & 0x40) >> 6) + +#define DEVID_9005_CLASS(id) (((id) & 0xFF00) >> 8) +#define DEVID_9005_CLASS_SPI 0x0 /* Parallel SCSI */ + +#define SUBID_9005_TYPE(id) ((id) & 0xF) +#define SUBID_9005_TYPE_MB 0xF /* On Motherboard */ +#define SUBID_9005_TYPE_CARD 0x0 /* Standard Card */ +#define SUBID_9005_TYPE_LCCARD 0x1 /* Low Cost Card */ +#define SUBID_9005_TYPE_RAID 0x3 /* Combined with Raid */ + +#define SUBID_9005_TYPE_KNOWN(id) \ + ((((id) & 0xF) == SUBID_9005_TYPE_MB) \ + || (((id) & 0xF) == SUBID_9005_TYPE_CARD) \ + || (((id) & 0xF) == SUBID_9005_TYPE_LCCARD) \ + || (((id) & 0xF) == SUBID_9005_TYPE_RAID)) + +#define SUBID_9005_MAXRATE(id) (((id) & 0x30) >> 4) +#define SUBID_9005_MAXRATE_ULTRA2 0x0 +#define SUBID_9005_MAXRATE_ULTRA 0x1 +#define SUBID_9005_MAXRATE_U160 0x2 +#define SUBID_9005_MAXRATE_RESERVED 0x3 + +#define SUBID_9005_SEEPTYPE(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? ((id) & 0xC0) >> 6 \ + : ((id) & 0x300) >> 8) +#define SUBID_9005_SEEPTYPE_NONE 0x0 +#define SUBID_9005_SEEPTYPE_1K 0x1 +#define SUBID_9005_SEEPTYPE_2K_4K 0x2 +#define SUBID_9005_SEEPTYPE_RESERVED 0x3 +#define SUBID_9005_AUTOTERM(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? (((id) & 0x400) >> 10) == 0 \ + : (((id) & 0x40) >> 6) == 0) + +#define SUBID_9005_NUMCHAN(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? ((id) & 0x300) >> 8 \ + : ((id) & 0xC00) >> 10) + +#define SUBID_9005_LEGACYCONN(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? 0 \ + : ((id) & 0x80) >> 7) + +#define SUBID_9005_MFUNCENB(id) \ + ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB) \ + ? ((id) & 0x800) >> 11 \ + : ((id) & 0x1000) >> 12) +/* + * Informational only. Should use chip register to be + * certain, but may be use in identification strings. + */ +#define SUBID_9005_CARD_SCSIWIDTH_MASK 0x2000 +#define SUBID_9005_CARD_PCIWIDTH_MASK 0x4000 +#define SUBID_9005_CARD_SEDIFF_MASK 0x8000 + +static ahc_device_setup_t ahc_aic785X_setup; +static ahc_device_setup_t ahc_aic7860_setup; +static ahc_device_setup_t ahc_apa1480_setup; +static ahc_device_setup_t ahc_aic7870_setup; +static ahc_device_setup_t ahc_aic7870h_setup; +static ahc_device_setup_t ahc_aha394X_setup; +static ahc_device_setup_t ahc_aha394Xh_setup; +static ahc_device_setup_t ahc_aha494X_setup; +static ahc_device_setup_t ahc_aha494Xh_setup; +static ahc_device_setup_t ahc_aha398X_setup; +static ahc_device_setup_t ahc_aic7880_setup; +static ahc_device_setup_t ahc_aic7880h_setup; +static ahc_device_setup_t ahc_aha2940Pro_setup; +static ahc_device_setup_t ahc_aha394XU_setup; +static ahc_device_setup_t ahc_aha394XUh_setup; +static ahc_device_setup_t ahc_aha398XU_setup; +static ahc_device_setup_t ahc_aic7890_setup; +static ahc_device_setup_t ahc_aic7892_setup; +static ahc_device_setup_t ahc_aic7895_setup; +static ahc_device_setup_t ahc_aic7895h_setup; +static ahc_device_setup_t ahc_aic7896_setup; +static ahc_device_setup_t ahc_aic7899_setup; +static ahc_device_setup_t ahc_aha29160C_setup; +static ahc_device_setup_t ahc_raid_setup; +static ahc_device_setup_t ahc_aha394XX_setup; +static ahc_device_setup_t ahc_aha494XX_setup; +static ahc_device_setup_t ahc_aha398XX_setup; + +static const struct ahc_pci_identity ahc_pci_ident_table[] = { + /* aic7850 based controllers */ + { + ID_AHA_2902_04_10_15_20C_30C, + ID_ALL_MASK, + "Adaptec 2902/04/10/15/20C/30C SCSI adapter", + ahc_aic785X_setup + }, + /* aic7860 based controllers */ + { + ID_AHA_2930CU, + ID_ALL_MASK, + "Adaptec 2930CU SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AHA_1480A & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 1480A Ultra SCSI adapter", + ahc_apa1480_setup + }, + { + ID_AHA_2940AU_0 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940A Ultra SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AHA_2940AU_CN & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940A/CN Ultra SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AHA_2930C_VAR & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2930C Ultra SCSI adapter (VAR)", + ahc_aic7860_setup + }, + /* aic7870 based controllers */ + { + ID_AHA_2940, + ID_ALL_MASK, + "Adaptec 2940 SCSI adapter", + ahc_aic7870_setup + }, + { + ID_AHA_3940, + ID_ALL_MASK, + "Adaptec 3940 SCSI adapter", + ahc_aha394X_setup + }, + { + ID_AHA_398X, + ID_ALL_MASK, + "Adaptec 398X SCSI RAID adapter", + ahc_aha398X_setup + }, + { + ID_AHA_2944, + ID_ALL_MASK, + "Adaptec 2944 SCSI adapter", + ahc_aic7870h_setup + }, + { + ID_AHA_3944, + ID_ALL_MASK, + "Adaptec 3944 SCSI adapter", + ahc_aha394Xh_setup + }, + { + ID_AHA_4944, + ID_ALL_MASK, + "Adaptec 4944 SCSI adapter", + ahc_aha494Xh_setup + }, + /* aic7880 based controllers */ + { + ID_AHA_2940U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940 Ultra SCSI adapter", + ahc_aic7880_setup + }, + { + ID_AHA_3940U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 3940 Ultra SCSI adapter", + ahc_aha394XU_setup + }, + { + ID_AHA_2944U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2944 Ultra SCSI adapter", + ahc_aic7880h_setup + }, + { + ID_AHA_3944U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 3944 Ultra SCSI adapter", + ahc_aha394XUh_setup + }, + { + ID_AHA_398XU & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 398X Ultra SCSI RAID adapter", + ahc_aha398XU_setup + }, + { + /* + * XXX Don't know the slot numbers + * so we can't identify channels + */ + ID_AHA_4944U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 4944 Ultra SCSI adapter", + ahc_aic7880h_setup + }, + { + ID_AHA_2930U & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2930 Ultra SCSI adapter", + ahc_aic7880_setup + }, + { + ID_AHA_2940U_PRO & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940 Pro Ultra SCSI adapter", + ahc_aha2940Pro_setup + }, + { + ID_AHA_2940U_CN & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec 2940/CN Ultra SCSI adapter", + ahc_aic7880_setup + }, + /* Ignore all SISL (AAC on MB) based controllers. */ + { + ID_9005_SISL_ID, + ID_9005_SISL_MASK, + NULL, + NULL + }, + /* aic7890 based controllers */ + { + ID_AHA_2930U2, + ID_ALL_MASK, + "Adaptec 2930 Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AHA_2940U2B, + ID_ALL_MASK, + "Adaptec 2940B Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AHA_2940U2_OEM, + ID_ALL_MASK, + "Adaptec 2940 Ultra2 SCSI adapter (OEM)", + ahc_aic7890_setup + }, + { + ID_AHA_2940U2, + ID_ALL_MASK, + "Adaptec 2940 Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AHA_2950U2B, + ID_ALL_MASK, + "Adaptec 2950 Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AIC7890_ARO, + ID_ALL_MASK, + "Adaptec aic7890/91 Ultra2 SCSI adapter (ARO)", + ahc_aic7890_setup + }, + { + ID_AAA_131U2, + ID_ALL_MASK, + "Adaptec AAA-131 Ultra2 RAID adapter", + ahc_aic7890_setup + }, + /* aic7892 based controllers */ + { + ID_AHA_29160, + ID_ALL_MASK, + "Adaptec 29160 Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AHA_29160_CPQ, + ID_ALL_MASK, + "Adaptec (Compaq OEM) 29160 Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AHA_29160N, + ID_ALL_MASK, + "Adaptec 29160N Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AHA_29160C, + ID_ALL_MASK, + "Adaptec 29160C Ultra160 SCSI adapter", + ahc_aha29160C_setup + }, + { + ID_AHA_29160B, + ID_ALL_MASK, + "Adaptec 29160B Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AHA_19160B, + ID_ALL_MASK, + "Adaptec 19160B Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AIC7892_ARO, + ID_ALL_MASK, + "Adaptec aic7892 Ultra160 SCSI adapter (ARO)", + ahc_aic7892_setup + }, + { + ID_AHA_2915_30LP, + ID_ALL_MASK, + "Adaptec 2915/30LP Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + /* aic7895 based controllers */ + { + ID_AHA_2940U_DUAL, + ID_ALL_MASK, + "Adaptec 2940/DUAL Ultra SCSI adapter", + ahc_aic7895_setup + }, + { + ID_AHA_3940AU, + ID_ALL_MASK, + "Adaptec 3940A Ultra SCSI adapter", + ahc_aic7895_setup + }, + { + ID_AHA_3944AU, + ID_ALL_MASK, + "Adaptec 3944A Ultra SCSI adapter", + ahc_aic7895h_setup + }, + { + ID_AIC7895_ARO, + ID_AIC7895_ARO_MASK, + "Adaptec aic7895 Ultra SCSI adapter (ARO)", + ahc_aic7895_setup + }, + /* aic7896/97 based controllers */ + { + ID_AHA_3950U2B_0, + ID_ALL_MASK, + "Adaptec 3950B Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AHA_3950U2B_1, + ID_ALL_MASK, + "Adaptec 3950B Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AHA_3950U2D_0, + ID_ALL_MASK, + "Adaptec 3950D Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AHA_3950U2D_1, + ID_ALL_MASK, + "Adaptec 3950D Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AIC7896_ARO, + ID_ALL_MASK, + "Adaptec aic7896/97 Ultra2 SCSI adapter (ARO)", + ahc_aic7896_setup + }, + /* aic7899 based controllers */ + { + ID_AHA_3960D, + ID_ALL_MASK, + "Adaptec 3960D Ultra160 SCSI adapter", + ahc_aic7899_setup + }, + { + ID_AHA_3960D_CPQ, + ID_ALL_MASK, + "Adaptec (Compaq OEM) 3960D Ultra160 SCSI adapter", + ahc_aic7899_setup + }, + { + ID_AIC7899_ARO, + ID_ALL_MASK, + "Adaptec aic7899 Ultra160 SCSI adapter (ARO)", + ahc_aic7899_setup + }, + /* Generic chip probes for devices we don't know 'exactly' */ + { + ID_AIC7850 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7850 SCSI adapter", + ahc_aic785X_setup + }, + { + ID_AIC7855 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7855 SCSI adapter", + ahc_aic785X_setup + }, + { + ID_AIC7859 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7859 SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AIC7860 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7860 Ultra SCSI adapter", + ahc_aic7860_setup + }, + { + ID_AIC7870 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7870 SCSI adapter", + ahc_aic7870_setup + }, + { + ID_AIC7880 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7880 Ultra SCSI adapter", + ahc_aic7880_setup + }, + { + ID_AIC7890 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec aic7890/91 Ultra2 SCSI adapter", + ahc_aic7890_setup + }, + { + ID_AIC7892 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec aic7892 Ultra160 SCSI adapter", + ahc_aic7892_setup + }, + { + ID_AIC7895 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7895 Ultra SCSI adapter", + ahc_aic7895_setup + }, + { + ID_AIC7896 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec aic7896/97 Ultra2 SCSI adapter", + ahc_aic7896_setup + }, + { + ID_AIC7899 & ID_9005_GENERIC_MASK, + ID_9005_GENERIC_MASK, + "Adaptec aic7899 Ultra160 SCSI adapter", + ahc_aic7899_setup + }, + { + ID_AIC7810 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7810 RAID memory controller", + ahc_raid_setup + }, + { + ID_AIC7815 & ID_DEV_VENDOR_MASK, + ID_DEV_VENDOR_MASK, + "Adaptec aic7815 RAID memory controller", + ahc_raid_setup + } +}; + +static const u_int ahc_num_pci_devs = ARRAY_SIZE(ahc_pci_ident_table); + +#define AHC_394X_SLOT_CHANNEL_A 4 +#define AHC_394X_SLOT_CHANNEL_B 5 + +#define AHC_398X_SLOT_CHANNEL_A 4 +#define AHC_398X_SLOT_CHANNEL_B 8 +#define AHC_398X_SLOT_CHANNEL_C 12 + +#define AHC_494X_SLOT_CHANNEL_A 4 +#define AHC_494X_SLOT_CHANNEL_B 5 +#define AHC_494X_SLOT_CHANNEL_C 6 +#define AHC_494X_SLOT_CHANNEL_D 7 + +#define DEVCONFIG 0x40 +#define PCIERRGENDIS 0x80000000ul +#define SCBSIZE32 0x00010000ul /* aic789X only */ +#define REXTVALID 0x00001000ul /* ultra cards only */ +#define MPORTMODE 0x00000400ul /* aic7870+ only */ +#define RAMPSM 0x00000200ul /* aic7870+ only */ +#define VOLSENSE 0x00000100ul +#define PCI64BIT 0x00000080ul /* 64Bit PCI bus (Ultra2 Only)*/ +#define SCBRAMSEL 0x00000080ul +#define MRDCEN 0x00000040ul +#define EXTSCBTIME 0x00000020ul /* aic7870 only */ +#define EXTSCBPEN 0x00000010ul /* aic7870 only */ +#define BERREN 0x00000008ul +#define DACEN 0x00000004ul +#define STPWLEVEL 0x00000002ul +#define DIFACTNEGEN 0x00000001ul /* aic7870 only */ + +#define CSIZE_LATTIME 0x0c +#define CACHESIZE 0x0000003ful /* only 5 bits */ +#define LATTIME 0x0000ff00ul + +/* PCI STATUS definitions */ +#define DPE 0x80 +#define SSE 0x40 +#define RMA 0x20 +#define RTA 0x10 +#define STA 0x08 +#define DPR 0x01 + +static int ahc_9005_subdevinfo_valid(uint16_t vendor, uint16_t device, + uint16_t subvendor, uint16_t subdevice); +static int ahc_ext_scbram_present(struct ahc_softc *ahc); +static void ahc_scbram_config(struct ahc_softc *ahc, int enable, + int pcheck, int fast, int large); +static void ahc_probe_ext_scbram(struct ahc_softc *ahc); +static void check_extport(struct ahc_softc *ahc, u_int *sxfrctl1); +static void ahc_parse_pci_eeprom(struct ahc_softc *ahc, + struct seeprom_config *sc); +static void configure_termination(struct ahc_softc *ahc, + struct seeprom_descriptor *sd, + u_int adapter_control, + u_int *sxfrctl1); + +static void ahc_new_term_detect(struct ahc_softc *ahc, + int *enableSEC_low, + int *enableSEC_high, + int *enablePRI_low, + int *enablePRI_high, + int *eeprom_present); +static void aic787X_cable_detect(struct ahc_softc *ahc, int *internal50_present, + int *internal68_present, + int *externalcable_present, + int *eeprom_present); +static void aic785X_cable_detect(struct ahc_softc *ahc, int *internal50_present, + int *externalcable_present, + int *eeprom_present); +static void write_brdctl(struct ahc_softc *ahc, uint8_t value); +static uint8_t read_brdctl(struct ahc_softc *ahc); +static void ahc_pci_intr(struct ahc_softc *ahc); +static int ahc_pci_chip_init(struct ahc_softc *ahc); + +static int +ahc_9005_subdevinfo_valid(uint16_t device, uint16_t vendor, + uint16_t subdevice, uint16_t subvendor) +{ + int result; + + /* Default to invalid. */ + result = 0; + if (vendor == 0x9005 + && subvendor == 0x9005 + && subdevice != device + && SUBID_9005_TYPE_KNOWN(subdevice) != 0) { + + switch (SUBID_9005_TYPE(subdevice)) { + case SUBID_9005_TYPE_MB: + break; + case SUBID_9005_TYPE_CARD: + case SUBID_9005_TYPE_LCCARD: + /* + * Currently only trust Adaptec cards to + * get the sub device info correct. + */ + if (DEVID_9005_TYPE(device) == DEVID_9005_TYPE_HBA) + result = 1; + break; + case SUBID_9005_TYPE_RAID: + break; + default: + break; + } + } + return (result); +} + +const struct ahc_pci_identity * +ahc_find_pci_device(ahc_dev_softc_t pci) +{ + uint64_t full_id; + uint16_t device; + uint16_t vendor; + uint16_t subdevice; + uint16_t subvendor; + const struct ahc_pci_identity *entry; + u_int i; + + vendor = ahc_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2); + device = ahc_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2); + subvendor = ahc_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2); + subdevice = ahc_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2); + full_id = ahc_compose_id(device, vendor, subdevice, subvendor); + + /* + * If the second function is not hooked up, ignore it. + * Unfortunately, not all MB vendors implement the + * subdevice ID as per the Adaptec spec, so do our best + * to sanity check it prior to accepting the subdevice + * ID as valid. + */ + if (ahc_get_pci_function(pci) > 0 + && ahc_9005_subdevinfo_valid(device, vendor, subdevice, subvendor) + && SUBID_9005_MFUNCENB(subdevice) == 0) + return (NULL); + + for (i = 0; i < ahc_num_pci_devs; i++) { + entry = &ahc_pci_ident_table[i]; + if (entry->full_id == (full_id & entry->id_mask)) { + /* Honor exclusion entries. */ + if (entry->name == NULL) + return (NULL); + return (entry); + } + } + return (NULL); +} + +int +ahc_pci_config(struct ahc_softc *ahc, const struct ahc_pci_identity *entry) +{ + u_int command; + u_int our_id; + u_int sxfrctl1; + u_int scsiseq; + u_int dscommand0; + uint32_t devconfig; + int error; + uint8_t sblkctl; + + our_id = 0; + error = entry->setup(ahc); + if (error != 0) + return (error); + ahc->chip |= AHC_PCI; + ahc->description = entry->name; + + pci_set_power_state(ahc->dev_softc, AHC_POWER_STATE_D0); + + error = ahc_pci_map_registers(ahc); + if (error != 0) + return (error); + + /* + * Before we continue probing the card, ensure that + * its interrupts are *disabled*. We don't want + * a misstep to hang the machine in an interrupt + * storm. + */ + ahc_intr_enable(ahc, FALSE); + + devconfig = ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4); + + /* + * If we need to support high memory, enable dual + * address cycles. This bit must be set to enable + * high address bit generation even if we are on a + * 64bit bus (PCI64BIT set in devconfig). + */ + if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { + + if (bootverbose) + printk("%s: Enabling 39Bit Addressing\n", + ahc_name(ahc)); + devconfig |= DACEN; + } + + /* Ensure that pci error generation, a test feature, is disabled. */ + devconfig |= PCIERRGENDIS; + + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); + + /* Ensure busmastering is enabled */ + command = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/2); + command |= PCIM_CMD_BUSMASTEREN; + + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, command, /*bytes*/2); + + /* On all PCI adapters, we allow SCB paging */ + ahc->flags |= AHC_PAGESCBS; + + error = ahc_softc_init(ahc); + if (error != 0) + return (error); + + /* + * Disable PCI parity error checking. Users typically + * do this to work around broken PCI chipsets that get + * the parity timing wrong and thus generate lots of spurious + * errors. The chip only allows us to disable *all* parity + * error reporting when doing this, so CIO bus, scb ram, and + * scratch ram parity errors will be ignored too. + */ + if ((ahc->flags & AHC_DISABLE_PCI_PERR) != 0) + ahc->seqctl |= FAILDIS; + + ahc->bus_intr = ahc_pci_intr; + ahc->bus_chip_init = ahc_pci_chip_init; + + /* Remember how the card was setup in case there is no SEEPROM */ + if ((ahc_inb(ahc, HCNTRL) & POWRDN) == 0) { + ahc_pause(ahc); + if ((ahc->features & AHC_ULTRA2) != 0) + our_id = ahc_inb(ahc, SCSIID_ULTRA2) & OID; + else + our_id = ahc_inb(ahc, SCSIID) & OID; + sxfrctl1 = ahc_inb(ahc, SXFRCTL1) & STPWEN; + scsiseq = ahc_inb(ahc, SCSISEQ); + } else { + sxfrctl1 = STPWEN; + our_id = 7; + scsiseq = 0; + } + + error = ahc_reset(ahc, /*reinit*/FALSE); + if (error != 0) + return (ENXIO); + + if ((ahc->features & AHC_DT) != 0) { + u_int sfunct; + + /* Perform ALT-Mode Setup */ + sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE; + ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE); + ahc_outb(ahc, OPTIONMODE, + OPTIONMODE_DEFAULTS|AUTOACKEN|BUSFREEREV|EXPPHASEDIS); + ahc_outb(ahc, SFUNCT, sfunct); + + /* Normal mode setup */ + ahc_outb(ahc, CRCCONTROL1, CRCVALCHKEN|CRCENDCHKEN|CRCREQCHKEN + |TARGCRCENDEN); + } + + dscommand0 = ahc_inb(ahc, DSCOMMAND0); + dscommand0 |= MPARCKEN|CACHETHEN; + if ((ahc->features & AHC_ULTRA2) != 0) { + + /* + * DPARCKEN doesn't work correctly on + * some MBs so don't use it. + */ + dscommand0 &= ~DPARCKEN; + } + + /* + * Handle chips that must have cache line + * streaming (dis/en)abled. + */ + if ((ahc->bugs & AHC_CACHETHEN_DIS_BUG) != 0) + dscommand0 |= CACHETHEN; + + if ((ahc->bugs & AHC_CACHETHEN_BUG) != 0) + dscommand0 &= ~CACHETHEN; + + ahc_outb(ahc, DSCOMMAND0, dscommand0); + + ahc->pci_cachesize = + ahc_pci_read_config(ahc->dev_softc, CSIZE_LATTIME, + /*bytes*/1) & CACHESIZE; + ahc->pci_cachesize *= 4; + + if ((ahc->bugs & AHC_PCI_2_1_RETRY_BUG) != 0 + && ahc->pci_cachesize == 4) { + + ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME, + 0, /*bytes*/1); + ahc->pci_cachesize = 0; + } + + /* + * We cannot perform ULTRA speeds without the presence + * of the external precision resistor. + */ + if ((ahc->features & AHC_ULTRA) != 0) { + uint32_t devconfig; + + devconfig = ahc_pci_read_config(ahc->dev_softc, + DEVCONFIG, /*bytes*/4); + if ((devconfig & REXTVALID) == 0) + ahc->features &= ~AHC_ULTRA; + } + + /* See if we have a SEEPROM and perform auto-term */ + check_extport(ahc, &sxfrctl1); + + /* + * Take the LED out of diagnostic mode + */ + sblkctl = ahc_inb(ahc, SBLKCTL); + ahc_outb(ahc, SBLKCTL, (sblkctl & ~(DIAGLEDEN|DIAGLEDON))); + + if ((ahc->features & AHC_ULTRA2) != 0) { + ahc_outb(ahc, DFF_THRSH, RD_DFTHRSH_MAX|WR_DFTHRSH_MAX); + } else { + ahc_outb(ahc, DSPCISTATUS, DFTHRSH_100); + } + + if (ahc->flags & AHC_USEDEFAULTS) { + /* + * PCI Adapter default setup + * Should only be used if the adapter does not have + * a SEEPROM. + */ + /* See if someone else set us up already */ + if ((ahc->flags & AHC_NO_BIOS_INIT) == 0 + && scsiseq != 0) { + printk("%s: Using left over BIOS settings\n", + ahc_name(ahc)); + ahc->flags &= ~AHC_USEDEFAULTS; + ahc->flags |= AHC_BIOS_ENABLED; + } else { + /* + * Assume only one connector and always turn + * on termination. + */ + our_id = 0x07; + sxfrctl1 = STPWEN; + } + ahc_outb(ahc, SCSICONF, our_id|ENSPCHK|RESET_SCSI); + + ahc->our_id = our_id; + } + + /* + * Take a look to see if we have external SRAM. + * We currently do not attempt to use SRAM that is + * shared among multiple controllers. + */ + ahc_probe_ext_scbram(ahc); + + /* + * Record our termination setting for the + * generic initialization routine. + */ + if ((sxfrctl1 & STPWEN) != 0) + ahc->flags |= AHC_TERM_ENB_A; + + /* + * Save chip register configuration data for chip resets + * that occur during runtime and resume events. + */ + ahc->bus_softc.pci_softc.devconfig = + ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4); + ahc->bus_softc.pci_softc.command = + ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/1); + ahc->bus_softc.pci_softc.csize_lattime = + ahc_pci_read_config(ahc->dev_softc, CSIZE_LATTIME, /*bytes*/1); + ahc->bus_softc.pci_softc.dscommand0 = ahc_inb(ahc, DSCOMMAND0); + ahc->bus_softc.pci_softc.dspcistatus = ahc_inb(ahc, DSPCISTATUS); + if ((ahc->features & AHC_DT) != 0) { + u_int sfunct; + + sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE; + ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE); + ahc->bus_softc.pci_softc.optionmode = ahc_inb(ahc, OPTIONMODE); + ahc->bus_softc.pci_softc.targcrccnt = ahc_inw(ahc, TARGCRCCNT); + ahc_outb(ahc, SFUNCT, sfunct); + ahc->bus_softc.pci_softc.crccontrol1 = + ahc_inb(ahc, CRCCONTROL1); + } + if ((ahc->features & AHC_MULTI_FUNC) != 0) + ahc->bus_softc.pci_softc.scbbaddr = ahc_inb(ahc, SCBBADDR); + + if ((ahc->features & AHC_ULTRA2) != 0) + ahc->bus_softc.pci_softc.dff_thrsh = ahc_inb(ahc, DFF_THRSH); + + /* Core initialization */ + error = ahc_init(ahc); + if (error != 0) + return (error); + ahc->init_level++; + + /* + * Allow interrupts now that we are completely setup. + */ + return ahc_pci_map_int(ahc); +} + +/* + * Test for the presence of external sram in an + * "unshared" configuration. + */ +static int +ahc_ext_scbram_present(struct ahc_softc *ahc) +{ + u_int chip; + int ramps; + int single_user; + uint32_t devconfig; + + chip = ahc->chip & AHC_CHIPID_MASK; + devconfig = ahc_pci_read_config(ahc->dev_softc, + DEVCONFIG, /*bytes*/4); + single_user = (devconfig & MPORTMODE) != 0; + + if ((ahc->features & AHC_ULTRA2) != 0) + ramps = (ahc_inb(ahc, DSCOMMAND0) & RAMPS) != 0; + else if (chip == AHC_AIC7895 || chip == AHC_AIC7895C) + /* + * External SCBRAM arbitration is flakey + * on these chips. Unfortunately this means + * we don't use the extra SCB ram space on the + * 3940AUW. + */ + ramps = 0; + else if (chip >= AHC_AIC7870) + ramps = (devconfig & RAMPSM) != 0; + else + ramps = 0; + + if (ramps && single_user) + return (1); + return (0); +} + +/* + * Enable external scbram. + */ +static void +ahc_scbram_config(struct ahc_softc *ahc, int enable, int pcheck, + int fast, int large) +{ + uint32_t devconfig; + + if (ahc->features & AHC_MULTI_FUNC) { + /* + * Set the SCB Base addr (highest address bit) + * depending on which channel we are. + */ + ahc_outb(ahc, SCBBADDR, ahc_get_pci_function(ahc->dev_softc)); + } + + ahc->flags &= ~AHC_LSCBS_ENABLED; + if (large) + ahc->flags |= AHC_LSCBS_ENABLED; + devconfig = ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4); + if ((ahc->features & AHC_ULTRA2) != 0) { + u_int dscommand0; + + dscommand0 = ahc_inb(ahc, DSCOMMAND0); + if (enable) + dscommand0 &= ~INTSCBRAMSEL; + else + dscommand0 |= INTSCBRAMSEL; + if (large) + dscommand0 &= ~USCBSIZE32; + else + dscommand0 |= USCBSIZE32; + ahc_outb(ahc, DSCOMMAND0, dscommand0); + } else { + if (fast) + devconfig &= ~EXTSCBTIME; + else + devconfig |= EXTSCBTIME; + if (enable) + devconfig &= ~SCBRAMSEL; + else + devconfig |= SCBRAMSEL; + if (large) + devconfig &= ~SCBSIZE32; + else + devconfig |= SCBSIZE32; + } + if (pcheck) + devconfig |= EXTSCBPEN; + else + devconfig &= ~EXTSCBPEN; + + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); +} + +/* + * Take a look to see if we have external SRAM. + * We currently do not attempt to use SRAM that is + * shared among multiple controllers. + */ +static void +ahc_probe_ext_scbram(struct ahc_softc *ahc) +{ + int num_scbs; + int test_num_scbs; + int enable; + int pcheck; + int fast; + int large; + + enable = FALSE; + pcheck = FALSE; + fast = FALSE; + large = FALSE; + num_scbs = 0; + + if (ahc_ext_scbram_present(ahc) == 0) + goto done; + + /* + * Probe for the best parameters to use. + */ + ahc_scbram_config(ahc, /*enable*/TRUE, pcheck, fast, large); + num_scbs = ahc_probe_scbs(ahc); + if (num_scbs == 0) { + /* The SRAM wasn't really present. */ + goto done; + } + enable = TRUE; + + /* + * Clear any outstanding parity error + * and ensure that parity error reporting + * is enabled. + */ + ahc_outb(ahc, SEQCTL, 0); + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); + + /* Now see if we can do parity */ + ahc_scbram_config(ahc, enable, /*pcheck*/TRUE, fast, large); + num_scbs = ahc_probe_scbs(ahc); + if ((ahc_inb(ahc, INTSTAT) & BRKADRINT) == 0 + || (ahc_inb(ahc, ERROR) & MPARERR) == 0) + pcheck = TRUE; + + /* Clear any resulting parity error */ + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); + + /* Now see if we can do fast timing */ + ahc_scbram_config(ahc, enable, pcheck, /*fast*/TRUE, large); + test_num_scbs = ahc_probe_scbs(ahc); + if (test_num_scbs == num_scbs + && ((ahc_inb(ahc, INTSTAT) & BRKADRINT) == 0 + || (ahc_inb(ahc, ERROR) & MPARERR) == 0)) + fast = TRUE; + + /* + * See if we can use large SCBs and still maintain + * the same overall count of SCBs. + */ + if ((ahc->features & AHC_LARGE_SCBS) != 0) { + ahc_scbram_config(ahc, enable, pcheck, fast, /*large*/TRUE); + test_num_scbs = ahc_probe_scbs(ahc); + if (test_num_scbs >= num_scbs) { + large = TRUE; + num_scbs = test_num_scbs; + if (num_scbs >= 64) { + /* + * We have enough space to move the + * "busy targets table" into SCB space + * and make it qualify all the way to the + * lun level. + */ + ahc->flags |= AHC_SCB_BTT; + } + } + } +done: + /* + * Disable parity error reporting until we + * can load instruction ram. + */ + ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS); + /* Clear any latched parity error */ + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); + if (bootverbose && enable) { + printk("%s: External SRAM, %s access%s, %dbytes/SCB\n", + ahc_name(ahc), fast ? "fast" : "slow", + pcheck ? ", parity checking enabled" : "", + large ? 64 : 32); + } + ahc_scbram_config(ahc, enable, pcheck, fast, large); +} + +/* + * Perform some simple tests that should catch situations where + * our registers are invalidly mapped. + */ +int +ahc_pci_test_register_access(struct ahc_softc *ahc) +{ + int error; + u_int status1; + uint32_t cmd; + uint8_t hcntrl; + + error = EIO; + + /* + * Enable PCI error interrupt status, but suppress NMIs + * generated by SERR raised due to target aborts. + */ + cmd = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/2); + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, + cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2); + + /* + * First a simple test to see if any + * registers can be read. Reading + * HCNTRL has no side effects and has + * at least one bit that is guaranteed to + * be zero so it is a good register to + * use for this test. + */ + hcntrl = ahc_inb(ahc, HCNTRL); + + if (hcntrl == 0xFF) + goto fail; + + if ((hcntrl & CHIPRST) != 0) { + /* + * The chip has not been initialized since + * PCI/EISA/VLB bus reset. Don't trust + * "left over BIOS data". + */ + ahc->flags |= AHC_NO_BIOS_INIT; + } + + /* + * Next create a situation where write combining + * or read prefetching could be initiated by the + * CPU or host bridge. Our device does not support + * either, so look for data corruption and/or flagged + * PCI errors. First pause without causing another + * chip reset. + */ + hcntrl &= ~CHIPRST; + ahc_outb(ahc, HCNTRL, hcntrl|PAUSE); + while (ahc_is_paused(ahc) == 0) + ; + + /* Clear any PCI errors that occurred before our driver attached. */ + status1 = ahc_pci_read_config(ahc->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1, + status1, /*bytes*/1); + ahc_outb(ahc, CLRINT, CLRPARERR); + + ahc_outb(ahc, SEQCTL, PERRORDIS); + ahc_outb(ahc, SCBPTR, 0); + ahc_outl(ahc, SCB_BASE, 0x5aa555aa); + if (ahc_inl(ahc, SCB_BASE) != 0x5aa555aa) + goto fail; + + status1 = ahc_pci_read_config(ahc->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + if ((status1 & STA) != 0) + goto fail; + + error = 0; + +fail: + /* Silently clear any latched errors. */ + status1 = ahc_pci_read_config(ahc->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1, + status1, /*bytes*/1); + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS); + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2); + return (error); +} + +/* + * Check the external port logic for a serial eeprom + * and termination/cable detection contrls. + */ +static void +check_extport(struct ahc_softc *ahc, u_int *sxfrctl1) +{ + struct seeprom_descriptor sd; + struct seeprom_config *sc; + int have_seeprom; + int have_autoterm; + + sd.sd_ahc = ahc; + sd.sd_control_offset = SEECTL; + sd.sd_status_offset = SEECTL; + sd.sd_dataout_offset = SEECTL; + sc = ahc->seep_config; + + /* + * For some multi-channel devices, the c46 is simply too + * small to work. For the other controller types, we can + * get our information from either SEEPROM type. Set the + * type to start our probe with accordingly. + */ + if (ahc->flags & AHC_LARGE_SEEPROM) + sd.sd_chip = C56_66; + else + sd.sd_chip = C46; + + sd.sd_MS = SEEMS; + sd.sd_RDY = SEERDY; + sd.sd_CS = SEECS; + sd.sd_CK = SEECK; + sd.sd_DO = SEEDO; + sd.sd_DI = SEEDI; + + have_seeprom = ahc_acquire_seeprom(ahc, &sd); + if (have_seeprom) { + + if (bootverbose) + printk("%s: Reading SEEPROM...", ahc_name(ahc)); + + for (;;) { + u_int start_addr; + + start_addr = 32 * (ahc->channel - 'A'); + + have_seeprom = ahc_read_seeprom(&sd, (uint16_t *)sc, + start_addr, + sizeof(*sc)/2); + + if (have_seeprom) + have_seeprom = ahc_verify_cksum(sc); + + if (have_seeprom != 0 || sd.sd_chip == C56_66) { + if (bootverbose) { + if (have_seeprom == 0) + printk ("checksum error\n"); + else + printk ("done.\n"); + } + break; + } + sd.sd_chip = C56_66; + } + ahc_release_seeprom(&sd); + + /* Remember the SEEPROM type for later */ + if (sd.sd_chip == C56_66) + ahc->flags |= AHC_LARGE_SEEPROM; + } + + if (!have_seeprom) { + /* + * Pull scratch ram settings and treat them as + * if they are the contents of an seeprom if + * the 'ADPT' signature is found in SCB2. + * We manually compose the data as 16bit values + * to avoid endian issues. + */ + ahc_outb(ahc, SCBPTR, 2); + if (ahc_inb(ahc, SCB_BASE) == 'A' + && ahc_inb(ahc, SCB_BASE + 1) == 'D' + && ahc_inb(ahc, SCB_BASE + 2) == 'P' + && ahc_inb(ahc, SCB_BASE + 3) == 'T') { + uint16_t *sc_data; + int i; + + sc_data = (uint16_t *)sc; + for (i = 0; i < 32; i++, sc_data++) { + int j; + + j = i * 2; + *sc_data = ahc_inb(ahc, SRAM_BASE + j) + | ahc_inb(ahc, SRAM_BASE + j + 1) << 8; + } + have_seeprom = ahc_verify_cksum(sc); + if (have_seeprom) + ahc->flags |= AHC_SCB_CONFIG_USED; + } + /* + * Clear any SCB parity errors in case this data and + * its associated parity was not initialized by the BIOS + */ + ahc_outb(ahc, CLRINT, CLRPARERR); + ahc_outb(ahc, CLRINT, CLRBRKADRINT); + } + + if (!have_seeprom) { + if (bootverbose) + printk("%s: No SEEPROM available.\n", ahc_name(ahc)); + ahc->flags |= AHC_USEDEFAULTS; + kfree(ahc->seep_config); + ahc->seep_config = NULL; + sc = NULL; + } else { + ahc_parse_pci_eeprom(ahc, sc); + } + + /* + * Cards that have the external logic necessary to talk to + * a SEEPROM, are almost certain to have the remaining logic + * necessary for auto-termination control. This assumption + * hasn't failed yet... + */ + have_autoterm = have_seeprom; + + /* + * Some low-cost chips have SEEPROM and auto-term control built + * in, instead of using a GAL. They can tell us directly + * if the termination logic is enabled. + */ + if ((ahc->features & AHC_SPIOCAP) != 0) { + if ((ahc_inb(ahc, SPIOCAP) & SSPIOCPS) == 0) + have_autoterm = FALSE; + } + + if (have_autoterm) { + ahc->flags |= AHC_HAS_TERM_LOGIC; + ahc_acquire_seeprom(ahc, &sd); + configure_termination(ahc, &sd, sc->adapter_control, sxfrctl1); + ahc_release_seeprom(&sd); + } else if (have_seeprom) { + *sxfrctl1 &= ~STPWEN; + if ((sc->adapter_control & CFSTERM) != 0) + *sxfrctl1 |= STPWEN; + if (bootverbose) + printk("%s: Low byte termination %sabled\n", + ahc_name(ahc), + (*sxfrctl1 & STPWEN) ? "en" : "dis"); + } +} + +static void +ahc_parse_pci_eeprom(struct ahc_softc *ahc, struct seeprom_config *sc) +{ + /* + * Put the data we've collected down into SRAM + * where ahc_init will find it. + */ + int i; + int max_targ = sc->max_targets & CFMAXTARG; + u_int scsi_conf; + uint16_t discenable; + uint16_t ultraenb; + + discenable = 0; + ultraenb = 0; + if ((sc->adapter_control & CFULTRAEN) != 0) { + /* + * Determine if this adapter has a "newstyle" + * SEEPROM format. + */ + for (i = 0; i < max_targ; i++) { + if ((sc->device_flags[i] & CFSYNCHISULTRA) != 0) { + ahc->flags |= AHC_NEWEEPROM_FMT; + break; + } + } + } + + for (i = 0; i < max_targ; i++) { + u_int scsirate; + uint16_t target_mask; + + target_mask = 0x01 << i; + if (sc->device_flags[i] & CFDISC) + discenable |= target_mask; + if ((ahc->flags & AHC_NEWEEPROM_FMT) != 0) { + if ((sc->device_flags[i] & CFSYNCHISULTRA) != 0) + ultraenb |= target_mask; + } else if ((sc->adapter_control & CFULTRAEN) != 0) { + ultraenb |= target_mask; + } + if ((sc->device_flags[i] & CFXFER) == 0x04 + && (ultraenb & target_mask) != 0) { + /* Treat 10MHz as a non-ultra speed */ + sc->device_flags[i] &= ~CFXFER; + ultraenb &= ~target_mask; + } + if ((ahc->features & AHC_ULTRA2) != 0) { + u_int offset; + + if (sc->device_flags[i] & CFSYNCH) + offset = MAX_OFFSET_ULTRA2; + else + offset = 0; + ahc_outb(ahc, TARG_OFFSET + i, offset); + + /* + * The ultra enable bits contain the + * high bit of the ultra2 sync rate + * field. + */ + scsirate = (sc->device_flags[i] & CFXFER) + | ((ultraenb & target_mask) ? 0x8 : 0x0); + if (sc->device_flags[i] & CFWIDEB) + scsirate |= WIDEXFER; + } else { + scsirate = (sc->device_flags[i] & CFXFER) << 4; + if (sc->device_flags[i] & CFSYNCH) + scsirate |= SOFS; + if (sc->device_flags[i] & CFWIDEB) + scsirate |= WIDEXFER; + } + ahc_outb(ahc, TARG_SCSIRATE + i, scsirate); + } + ahc->our_id = sc->brtime_id & CFSCSIID; + + scsi_conf = (ahc->our_id & 0x7); + if (sc->adapter_control & CFSPARITY) + scsi_conf |= ENSPCHK; + if (sc->adapter_control & CFRESETB) + scsi_conf |= RESET_SCSI; + + ahc->flags |= (sc->adapter_control & CFBOOTCHAN) >> CFBOOTCHANSHIFT; + + if (sc->bios_control & CFEXTEND) + ahc->flags |= AHC_EXTENDED_TRANS_A; + + if (sc->bios_control & CFBIOSEN) + ahc->flags |= AHC_BIOS_ENABLED; + if (ahc->features & AHC_ULTRA + && (ahc->flags & AHC_NEWEEPROM_FMT) == 0) { + /* Should we enable Ultra mode? */ + if (!(sc->adapter_control & CFULTRAEN)) + /* Treat us as a non-ultra card */ + ultraenb = 0; + } + + if (sc->signature == CFSIGNATURE + || sc->signature == CFSIGNATURE2) { + uint32_t devconfig; + + /* Honor the STPWLEVEL settings */ + devconfig = ahc_pci_read_config(ahc->dev_softc, + DEVCONFIG, /*bytes*/4); + devconfig &= ~STPWLEVEL; + if ((sc->bios_control & CFSTPWLEVEL) != 0) + devconfig |= STPWLEVEL; + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, + devconfig, /*bytes*/4); + } + /* Set SCSICONF info */ + ahc_outb(ahc, SCSICONF, scsi_conf); + ahc_outb(ahc, DISC_DSB, ~(discenable & 0xff)); + ahc_outb(ahc, DISC_DSB + 1, ~((discenable >> 8) & 0xff)); + ahc_outb(ahc, ULTRA_ENB, ultraenb & 0xff); + ahc_outb(ahc, ULTRA_ENB + 1, (ultraenb >> 8) & 0xff); +} + +static void +configure_termination(struct ahc_softc *ahc, + struct seeprom_descriptor *sd, + u_int adapter_control, + u_int *sxfrctl1) +{ + uint8_t brddat; + + brddat = 0; + + /* + * Update the settings in sxfrctl1 to match the + * termination settings + */ + *sxfrctl1 = 0; + + /* + * SEECS must be on for the GALS to latch + * the data properly. Be sure to leave MS + * on or we will release the seeprom. + */ + SEEPROM_OUTB(sd, sd->sd_MS | sd->sd_CS); + if ((adapter_control & CFAUTOTERM) != 0 + || (ahc->features & AHC_NEW_TERMCTL) != 0) { + int internal50_present; + int internal68_present; + int externalcable_present; + int eeprom_present; + int enableSEC_low; + int enableSEC_high; + int enablePRI_low; + int enablePRI_high; + int sum; + + enableSEC_low = 0; + enableSEC_high = 0; + enablePRI_low = 0; + enablePRI_high = 0; + if ((ahc->features & AHC_NEW_TERMCTL) != 0) { + ahc_new_term_detect(ahc, &enableSEC_low, + &enableSEC_high, + &enablePRI_low, + &enablePRI_high, + &eeprom_present); + if ((adapter_control & CFSEAUTOTERM) == 0) { + if (bootverbose) + printk("%s: Manual SE Termination\n", + ahc_name(ahc)); + enableSEC_low = (adapter_control & CFSELOWTERM); + enableSEC_high = + (adapter_control & CFSEHIGHTERM); + } + if ((adapter_control & CFAUTOTERM) == 0) { + if (bootverbose) + printk("%s: Manual LVD Termination\n", + ahc_name(ahc)); + enablePRI_low = (adapter_control & CFSTERM); + enablePRI_high = (adapter_control & CFWSTERM); + } + /* Make the table calculations below happy */ + internal50_present = 0; + internal68_present = 1; + externalcable_present = 1; + } else if ((ahc->features & AHC_SPIOCAP) != 0) { + aic785X_cable_detect(ahc, &internal50_present, + &externalcable_present, + &eeprom_present); + /* Can never support a wide connector. */ + internal68_present = 0; + } else { + aic787X_cable_detect(ahc, &internal50_present, + &internal68_present, + &externalcable_present, + &eeprom_present); + } + + if ((ahc->features & AHC_WIDE) == 0) + internal68_present = 0; + + if (bootverbose + && (ahc->features & AHC_ULTRA2) == 0) { + printk("%s: internal 50 cable %s present", + ahc_name(ahc), + internal50_present ? "is":"not"); + + if ((ahc->features & AHC_WIDE) != 0) + printk(", internal 68 cable %s present", + internal68_present ? "is":"not"); + printk("\n%s: external cable %s present\n", + ahc_name(ahc), + externalcable_present ? "is":"not"); + } + if (bootverbose) + printk("%s: BIOS eeprom %s present\n", + ahc_name(ahc), eeprom_present ? "is" : "not"); + + if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0) { + /* + * The 50 pin connector is a separate bus, + * so force it to always be terminated. + * In the future, perform current sensing + * to determine if we are in the middle of + * a properly terminated bus. + */ + internal50_present = 0; + } + + /* + * Now set the termination based on what + * we found. + * Flash Enable = BRDDAT7 + * Secondary High Term Enable = BRDDAT6 + * Secondary Low Term Enable = BRDDAT5 (7890) + * Primary High Term Enable = BRDDAT4 (7890) + */ + if ((ahc->features & AHC_ULTRA2) == 0 + && (internal50_present != 0) + && (internal68_present != 0) + && (externalcable_present != 0)) { + printk("%s: Illegal cable configuration!!. " + "Only two connectors on the " + "adapter may be used at a " + "time!\n", ahc_name(ahc)); + + /* + * Pretend there are no cables in the hope + * that having all of the termination on + * gives us a more stable bus. + */ + internal50_present = 0; + internal68_present = 0; + externalcable_present = 0; + } + + if ((ahc->features & AHC_WIDE) != 0 + && ((externalcable_present == 0) + || (internal68_present == 0) + || (enableSEC_high != 0))) { + brddat |= BRDDAT6; + if (bootverbose) { + if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0) + printk("%s: 68 pin termination " + "Enabled\n", ahc_name(ahc)); + else + printk("%s: %sHigh byte termination " + "Enabled\n", ahc_name(ahc), + enableSEC_high ? "Secondary " + : ""); + } + } + + sum = internal50_present + internal68_present + + externalcable_present; + if (sum < 2 || (enableSEC_low != 0)) { + if ((ahc->features & AHC_ULTRA2) != 0) + brddat |= BRDDAT5; + else + *sxfrctl1 |= STPWEN; + if (bootverbose) { + if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0) + printk("%s: 50 pin termination " + "Enabled\n", ahc_name(ahc)); + else + printk("%s: %sLow byte termination " + "Enabled\n", ahc_name(ahc), + enableSEC_low ? "Secondary " + : ""); + } + } + + if (enablePRI_low != 0) { + *sxfrctl1 |= STPWEN; + if (bootverbose) + printk("%s: Primary Low Byte termination " + "Enabled\n", ahc_name(ahc)); + } + + /* + * Setup STPWEN before setting up the rest of + * the termination per the tech note on the U160 cards. + */ + ahc_outb(ahc, SXFRCTL1, *sxfrctl1); + + if (enablePRI_high != 0) { + brddat |= BRDDAT4; + if (bootverbose) + printk("%s: Primary High Byte " + "termination Enabled\n", + ahc_name(ahc)); + } + + write_brdctl(ahc, brddat); + + } else { + if ((adapter_control & CFSTERM) != 0) { + *sxfrctl1 |= STPWEN; + + if (bootverbose) + printk("%s: %sLow byte termination Enabled\n", + ahc_name(ahc), + (ahc->features & AHC_ULTRA2) ? "Primary " + : ""); + } + + if ((adapter_control & CFWSTERM) != 0 + && (ahc->features & AHC_WIDE) != 0) { + brddat |= BRDDAT6; + if (bootverbose) + printk("%s: %sHigh byte termination Enabled\n", + ahc_name(ahc), + (ahc->features & AHC_ULTRA2) + ? "Secondary " : ""); + } + + /* + * Setup STPWEN before setting up the rest of + * the termination per the tech note on the U160 cards. + */ + ahc_outb(ahc, SXFRCTL1, *sxfrctl1); + + if ((ahc->features & AHC_WIDE) != 0) + write_brdctl(ahc, brddat); + } + SEEPROM_OUTB(sd, sd->sd_MS); /* Clear CS */ +} + +static void +ahc_new_term_detect(struct ahc_softc *ahc, int *enableSEC_low, + int *enableSEC_high, int *enablePRI_low, + int *enablePRI_high, int *eeprom_present) +{ + uint8_t brdctl; + + /* + * BRDDAT7 = Eeprom + * BRDDAT6 = Enable Secondary High Byte termination + * BRDDAT5 = Enable Secondary Low Byte termination + * BRDDAT4 = Enable Primary high byte termination + * BRDDAT3 = Enable Primary low byte termination + */ + brdctl = read_brdctl(ahc); + *eeprom_present = brdctl & BRDDAT7; + *enableSEC_high = (brdctl & BRDDAT6); + *enableSEC_low = (brdctl & BRDDAT5); + *enablePRI_high = (brdctl & BRDDAT4); + *enablePRI_low = (brdctl & BRDDAT3); +} + +static void +aic787X_cable_detect(struct ahc_softc *ahc, int *internal50_present, + int *internal68_present, int *externalcable_present, + int *eeprom_present) +{ + uint8_t brdctl; + + /* + * First read the status of our cables. + * Set the rom bank to 0 since the + * bank setting serves as a multiplexor + * for the cable detection logic. + * BRDDAT5 controls the bank switch. + */ + write_brdctl(ahc, 0); + + /* + * Now read the state of the internal + * connectors. BRDDAT6 is INT50 and + * BRDDAT7 is INT68. + */ + brdctl = read_brdctl(ahc); + *internal50_present = (brdctl & BRDDAT6) ? 0 : 1; + *internal68_present = (brdctl & BRDDAT7) ? 0 : 1; + + /* + * Set the rom bank to 1 and determine + * the other signals. + */ + write_brdctl(ahc, BRDDAT5); + + /* + * Now read the state of the external + * connectors. BRDDAT6 is EXT68 and + * BRDDAT7 is EPROMPS. + */ + brdctl = read_brdctl(ahc); + *externalcable_present = (brdctl & BRDDAT6) ? 0 : 1; + *eeprom_present = (brdctl & BRDDAT7) ? 1 : 0; +} + +static void +aic785X_cable_detect(struct ahc_softc *ahc, int *internal50_present, + int *externalcable_present, int *eeprom_present) +{ + uint8_t brdctl; + uint8_t spiocap; + + spiocap = ahc_inb(ahc, SPIOCAP); + spiocap &= ~SOFTCMDEN; + spiocap |= EXT_BRDCTL; + ahc_outb(ahc, SPIOCAP, spiocap); + ahc_outb(ahc, BRDCTL, BRDRW|BRDCS); + ahc_flush_device_writes(ahc); + ahc_delay(500); + ahc_outb(ahc, BRDCTL, 0); + ahc_flush_device_writes(ahc); + ahc_delay(500); + brdctl = ahc_inb(ahc, BRDCTL); + *internal50_present = (brdctl & BRDDAT5) ? 0 : 1; + *externalcable_present = (brdctl & BRDDAT6) ? 0 : 1; + *eeprom_present = (ahc_inb(ahc, SPIOCAP) & EEPROM) ? 1 : 0; +} + +int +ahc_acquire_seeprom(struct ahc_softc *ahc, struct seeprom_descriptor *sd) +{ + int wait; + + if ((ahc->features & AHC_SPIOCAP) != 0 + && (ahc_inb(ahc, SPIOCAP) & SEEPROM) == 0) + return (0); + + /* + * Request access of the memory port. When access is + * granted, SEERDY will go high. We use a 1 second + * timeout which should be near 1 second more than + * is needed. Reason: after the chip reset, there + * should be no contention. + */ + SEEPROM_OUTB(sd, sd->sd_MS); + wait = 1000; /* 1 second timeout in msec */ + while (--wait && ((SEEPROM_STATUS_INB(sd) & sd->sd_RDY) == 0)) { + ahc_delay(1000); /* delay 1 msec */ + } + if ((SEEPROM_STATUS_INB(sd) & sd->sd_RDY) == 0) { + SEEPROM_OUTB(sd, 0); + return (0); + } + return(1); +} + +void +ahc_release_seeprom(struct seeprom_descriptor *sd) +{ + /* Release access to the memory port and the serial EEPROM. */ + SEEPROM_OUTB(sd, 0); +} + +static void +write_brdctl(struct ahc_softc *ahc, uint8_t value) +{ + uint8_t brdctl; + + if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { + brdctl = BRDSTB; + if (ahc->channel == 'B') + brdctl |= BRDCS; + } else if ((ahc->features & AHC_ULTRA2) != 0) { + brdctl = 0; + } else { + brdctl = BRDSTB|BRDCS; + } + ahc_outb(ahc, BRDCTL, brdctl); + ahc_flush_device_writes(ahc); + brdctl |= value; + ahc_outb(ahc, BRDCTL, brdctl); + ahc_flush_device_writes(ahc); + if ((ahc->features & AHC_ULTRA2) != 0) + brdctl |= BRDSTB_ULTRA2; + else + brdctl &= ~BRDSTB; + ahc_outb(ahc, BRDCTL, brdctl); + ahc_flush_device_writes(ahc); + if ((ahc->features & AHC_ULTRA2) != 0) + brdctl = 0; + else + brdctl &= ~BRDCS; + ahc_outb(ahc, BRDCTL, brdctl); +} + +static uint8_t +read_brdctl(struct ahc_softc *ahc) +{ + uint8_t brdctl; + uint8_t value; + + if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { + brdctl = BRDRW; + if (ahc->channel == 'B') + brdctl |= BRDCS; + } else if ((ahc->features & AHC_ULTRA2) != 0) { + brdctl = BRDRW_ULTRA2; + } else { + brdctl = BRDRW|BRDCS; + } + ahc_outb(ahc, BRDCTL, brdctl); + ahc_flush_device_writes(ahc); + value = ahc_inb(ahc, BRDCTL); + ahc_outb(ahc, BRDCTL, 0); + return (value); +} + +static void +ahc_pci_intr(struct ahc_softc *ahc) +{ + u_int error; + u_int status1; + + error = ahc_inb(ahc, ERROR); + if ((error & PCIERRSTAT) == 0) + return; + + status1 = ahc_pci_read_config(ahc->dev_softc, + PCIR_STATUS + 1, /*bytes*/1); + + printk("%s: PCI error Interrupt at seqaddr = 0x%x\n", + ahc_name(ahc), + ahc_inb(ahc, SEQADDR0) | (ahc_inb(ahc, SEQADDR1) << 8)); + + if (status1 & DPE) { + ahc->pci_target_perr_count++; + printk("%s: Data Parity Error Detected during address " + "or write data phase\n", ahc_name(ahc)); + } + if (status1 & SSE) { + printk("%s: Signal System Error Detected\n", ahc_name(ahc)); + } + if (status1 & RMA) { + printk("%s: Received a Master Abort\n", ahc_name(ahc)); + } + if (status1 & RTA) { + printk("%s: Received a Target Abort\n", ahc_name(ahc)); + } + if (status1 & STA) { + printk("%s: Signaled a Target Abort\n", ahc_name(ahc)); + } + if (status1 & DPR) { + printk("%s: Data Parity Error has been reported via PERR#\n", + ahc_name(ahc)); + } + + /* Clear latched errors. */ + ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1, + status1, /*bytes*/1); + + if ((status1 & (DPE|SSE|RMA|RTA|STA|DPR)) == 0) { + printk("%s: Latched PCIERR interrupt with " + "no status bits set\n", ahc_name(ahc)); + } else { + ahc_outb(ahc, CLRINT, CLRPARERR); + } + + if (ahc->pci_target_perr_count > AHC_PCI_TARGET_PERR_THRESH) { + printk( +"%s: WARNING WARNING WARNING WARNING\n" +"%s: Too many PCI parity errors observed as a target.\n" +"%s: Some device on this bus is generating bad parity.\n" +"%s: This is an error *observed by*, not *generated by*, this controller.\n" +"%s: PCI parity error checking has been disabled.\n" +"%s: WARNING WARNING WARNING WARNING\n", + ahc_name(ahc), ahc_name(ahc), ahc_name(ahc), + ahc_name(ahc), ahc_name(ahc), ahc_name(ahc)); + ahc->seqctl |= FAILDIS; + ahc_outb(ahc, SEQCTL, ahc->seqctl); + } + ahc_unpause(ahc); +} + +static int +ahc_pci_chip_init(struct ahc_softc *ahc) +{ + ahc_outb(ahc, DSCOMMAND0, ahc->bus_softc.pci_softc.dscommand0); + ahc_outb(ahc, DSPCISTATUS, ahc->bus_softc.pci_softc.dspcistatus); + if ((ahc->features & AHC_DT) != 0) { + u_int sfunct; + + sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE; + ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE); + ahc_outb(ahc, OPTIONMODE, ahc->bus_softc.pci_softc.optionmode); + ahc_outw(ahc, TARGCRCCNT, ahc->bus_softc.pci_softc.targcrccnt); + ahc_outb(ahc, SFUNCT, sfunct); + ahc_outb(ahc, CRCCONTROL1, + ahc->bus_softc.pci_softc.crccontrol1); + } + if ((ahc->features & AHC_MULTI_FUNC) != 0) + ahc_outb(ahc, SCBBADDR, ahc->bus_softc.pci_softc.scbbaddr); + + if ((ahc->features & AHC_ULTRA2) != 0) + ahc_outb(ahc, DFF_THRSH, ahc->bus_softc.pci_softc.dff_thrsh); + + return (ahc_chip_init(ahc)); +} + +#ifdef CONFIG_PM +void +ahc_pci_resume(struct ahc_softc *ahc) +{ + /* + * We assume that the OS has restored our register + * mappings, etc. Just update the config space registers + * that the OS doesn't know about and rely on our chip + * reset handler to handle the rest. + */ + ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, + ahc->bus_softc.pci_softc.devconfig, /*bytes*/4); + ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, + ahc->bus_softc.pci_softc.command, /*bytes*/1); + ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME, + ahc->bus_softc.pci_softc.csize_lattime, /*bytes*/1); + if ((ahc->flags & AHC_HAS_TERM_LOGIC) != 0) { + struct seeprom_descriptor sd; + u_int sxfrctl1; + + sd.sd_ahc = ahc; + sd.sd_control_offset = SEECTL; + sd.sd_status_offset = SEECTL; + sd.sd_dataout_offset = SEECTL; + + ahc_acquire_seeprom(ahc, &sd); + configure_termination(ahc, &sd, + ahc->seep_config->adapter_control, + &sxfrctl1); + ahc_release_seeprom(&sd); + } +} +#endif + +static int +ahc_aic785X_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = 'A'; + ahc->chip = AHC_AIC7850; + ahc->features = AHC_AIC7850_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG; + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev >= 1) + ahc->bugs |= AHC_PCI_2_1_RETRY_BUG; + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_aic7860_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = 'A'; + ahc->chip = AHC_AIC7860; + ahc->features = AHC_AIC7860_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG; + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev >= 1) + ahc->bugs |= AHC_PCI_2_1_RETRY_BUG; + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_apa1480_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7860_setup(ahc); + if (error != 0) + return (error); + ahc->features |= AHC_REMOVABLE; + return (0); +} + +static int +ahc_aic7870_setup(struct ahc_softc *ahc) +{ + + ahc->channel = 'A'; + ahc->chip = AHC_AIC7870; + ahc->features = AHC_AIC7870_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG; + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_aic7870h_setup(struct ahc_softc *ahc) +{ + int error = ahc_aic7870_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aha394X_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7870_setup(ahc); + if (error == 0) + error = ahc_aha394XX_setup(ahc); + return (error); +} + +static int +ahc_aha394Xh_setup(struct ahc_softc *ahc) +{ + int error = ahc_aha394X_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aha398X_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7870_setup(ahc); + if (error == 0) + error = ahc_aha398XX_setup(ahc); + return (error); +} + +static int +ahc_aha494X_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7870_setup(ahc); + if (error == 0) + error = ahc_aha494XX_setup(ahc); + return (error); +} + +static int +ahc_aha494Xh_setup(struct ahc_softc *ahc) +{ + int error = ahc_aha494X_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aic7880_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = 'A'; + ahc->chip = AHC_AIC7880; + ahc->features = AHC_AIC7880_FE; + ahc->bugs |= AHC_TMODE_WIDEODD_BUG; + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev >= 1) { + ahc->bugs |= AHC_PCI_2_1_RETRY_BUG; + } else { + ahc->bugs |= AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG; + } + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_aic7880h_setup(struct ahc_softc *ahc) +{ + int error = ahc_aic7880_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + + +static int +ahc_aha2940Pro_setup(struct ahc_softc *ahc) +{ + + ahc->flags |= AHC_INT50_SPEEDFLEX; + return (ahc_aic7880_setup(ahc)); +} + +static int +ahc_aha394XU_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7880_setup(ahc); + if (error == 0) + error = ahc_aha394XX_setup(ahc); + return (error); +} + +static int +ahc_aha394XUh_setup(struct ahc_softc *ahc) +{ + int error = ahc_aha394XU_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aha398XU_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7880_setup(ahc); + if (error == 0) + error = ahc_aha398XX_setup(ahc); + return (error); +} + +static int +ahc_aic7890_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = 'A'; + ahc->chip = AHC_AIC7890; + ahc->features = AHC_AIC7890_FE; + ahc->flags |= AHC_NEWEEPROM_FMT; + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev == 0) + ahc->bugs |= AHC_AUTOFLUSH_BUG|AHC_CACHETHEN_BUG; + ahc->instruction_ram_size = 768; + return (0); +} + +static int +ahc_aic7892_setup(struct ahc_softc *ahc) +{ + + ahc->channel = 'A'; + ahc->chip = AHC_AIC7892; + ahc->features = AHC_AIC7892_FE; + ahc->flags |= AHC_NEWEEPROM_FMT; + ahc->bugs |= AHC_SCBCHAN_UPLOAD_BUG; + ahc->instruction_ram_size = 1024; + return (0); +} + +static int +ahc_aic7895_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + uint8_t rev; + + pci = ahc->dev_softc; + ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A'; + /* + * The 'C' revision of the aic7895 has a few additional features. + */ + rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1); + if (rev >= 4) { + ahc->chip = AHC_AIC7895C; + ahc->features = AHC_AIC7895C_FE; + } else { + u_int command; + + ahc->chip = AHC_AIC7895; + ahc->features = AHC_AIC7895_FE; + + /* + * The BIOS disables the use of MWI transactions + * since it does not have the MWI bug work around + * we have. Disabling MWI reduces performance, so + * turn it on again. + */ + command = ahc_pci_read_config(pci, PCIR_COMMAND, /*bytes*/1); + command |= PCIM_CMD_MWRICEN; + ahc_pci_write_config(pci, PCIR_COMMAND, command, /*bytes*/1); + ahc->bugs |= AHC_PCI_MWI_BUG; + } + /* + * XXX Does CACHETHEN really not work??? What about PCI retry? + * on C level chips. Need to test, but for now, play it safe. + */ + ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_PCI_2_1_RETRY_BUG + | AHC_CACHETHEN_BUG; + +#if 0 + uint32_t devconfig; + + /* + * Cachesize must also be zero due to stray DAC + * problem when sitting behind some bridges. + */ + ahc_pci_write_config(pci, CSIZE_LATTIME, 0, /*bytes*/1); + devconfig = ahc_pci_read_config(pci, DEVCONFIG, /*bytes*/1); + devconfig |= MRDCEN; + ahc_pci_write_config(pci, DEVCONFIG, devconfig, /*bytes*/1); +#endif + ahc->flags |= AHC_NEWEEPROM_FMT; + ahc->instruction_ram_size = 512; + return (0); +} + +static int +ahc_aic7895h_setup(struct ahc_softc *ahc) +{ + int error = ahc_aic7895_setup(ahc); + + ahc->features |= AHC_HVD; + + return error; +} + +static int +ahc_aic7896_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A'; + ahc->chip = AHC_AIC7896; + ahc->features = AHC_AIC7896_FE; + ahc->flags |= AHC_NEWEEPROM_FMT; + ahc->bugs |= AHC_CACHETHEN_DIS_BUG; + ahc->instruction_ram_size = 768; + return (0); +} + +static int +ahc_aic7899_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A'; + ahc->chip = AHC_AIC7899; + ahc->features = AHC_AIC7899_FE; + ahc->flags |= AHC_NEWEEPROM_FMT; + ahc->bugs |= AHC_SCBCHAN_UPLOAD_BUG; + ahc->instruction_ram_size = 1024; + return (0); +} + +static int +ahc_aha29160C_setup(struct ahc_softc *ahc) +{ + int error; + + error = ahc_aic7899_setup(ahc); + if (error != 0) + return (error); + ahc->features |= AHC_REMOVABLE; + return (0); +} + +static int +ahc_raid_setup(struct ahc_softc *ahc) +{ + printk("RAID functionality unsupported\n"); + return (ENXIO); +} + +static int +ahc_aha394XX_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + switch (ahc_get_pci_slot(pci)) { + case AHC_394X_SLOT_CHANNEL_A: + ahc->channel = 'A'; + break; + case AHC_394X_SLOT_CHANNEL_B: + ahc->channel = 'B'; + break; + default: + printk("adapter at unexpected slot %d\n" + "unable to map to a channel\n", + ahc_get_pci_slot(pci)); + ahc->channel = 'A'; + } + return (0); +} + +static int +ahc_aha398XX_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + switch (ahc_get_pci_slot(pci)) { + case AHC_398X_SLOT_CHANNEL_A: + ahc->channel = 'A'; + break; + case AHC_398X_SLOT_CHANNEL_B: + ahc->channel = 'B'; + break; + case AHC_398X_SLOT_CHANNEL_C: + ahc->channel = 'C'; + break; + default: + printk("adapter at unexpected slot %d\n" + "unable to map to a channel\n", + ahc_get_pci_slot(pci)); + ahc->channel = 'A'; + break; + } + ahc->flags |= AHC_LARGE_SEEPROM; + return (0); +} + +static int +ahc_aha494XX_setup(struct ahc_softc *ahc) +{ + ahc_dev_softc_t pci; + + pci = ahc->dev_softc; + switch (ahc_get_pci_slot(pci)) { + case AHC_494X_SLOT_CHANNEL_A: + ahc->channel = 'A'; + break; + case AHC_494X_SLOT_CHANNEL_B: + ahc->channel = 'B'; + break; + case AHC_494X_SLOT_CHANNEL_C: + ahc->channel = 'C'; + break; + case AHC_494X_SLOT_CHANNEL_D: + ahc->channel = 'D'; + break; + default: + printk("adapter at unexpected slot %d\n" + "unable to map to a channel\n", + ahc_get_pci_slot(pci)); + ahc->channel = 'A'; + } + ahc->flags |= AHC_LARGE_SEEPROM; + return (0); +} |