diff options
Diffstat (limited to 'kernel/drivers/net/fddi')
41 files changed, 28683 insertions, 0 deletions
diff --git a/kernel/drivers/net/fddi/Kconfig b/kernel/drivers/net/fddi/Kconfig new file mode 100644 index 000000000..3a424c864 --- /dev/null +++ b/kernel/drivers/net/fddi/Kconfig @@ -0,0 +1,77 @@ +# +# FDDI network device configuration +# + +config FDDI + tristate "FDDI driver support" + depends on PCI || EISA || TC + ---help--- + Fiber Distributed Data Interface is a high speed local area network + design; essentially a replacement for high speed Ethernet. FDDI can + run over copper or fiber. If you are connected to such a network and + want a driver for the FDDI card in your computer, say Y here (and + then also Y to the driver for your FDDI card, below). Most people + will say N. + +if FDDI + +config DEFXX + tristate "Digital DEFTA/DEFEA/DEFPA adapter support" + depends on FDDI && (PCI || EISA || TC) + ---help--- + This is support for the DIGITAL series of TURBOchannel (DEFTA), + EISA (DEFEA) and PCI (DEFPA) controllers which can connect you + to a local FDDI network. + + To compile this driver as a module, choose M here: the module + will be called defxx. If unsure, say N. + +config DEFXX_MMIO + bool + prompt "Use MMIO instead of PIO" if PCI || EISA + depends on DEFXX + default n if PCI || EISA + default y + ---help--- + This instructs the driver to use EISA or PCI memory-mapped I/O + (MMIO) as appropriate instead of programmed I/O ports (PIO). + Enabling this gives an improvement in processing time in parts + of the driver, but it may cause problems with EISA (DEFEA) + adapters. TURBOchannel does not have the concept of I/O ports, + so MMIO is always used for these (DEFTA) adapters. + + If unsure, say N. + +config SKFP + tristate "SysKonnect FDDI PCI support" + depends on FDDI && PCI + select BITREVERSE + ---help--- + Say Y here if you have a SysKonnect FDDI PCI adapter. + The following adapters are supported by this driver: + - SK-5521 (SK-NET FDDI-UP) + - SK-5522 (SK-NET FDDI-UP DAS) + - SK-5541 (SK-NET FDDI-FP) + - SK-5543 (SK-NET FDDI-LP) + - SK-5544 (SK-NET FDDI-LP DAS) + - SK-5821 (SK-NET FDDI-UP64) + - SK-5822 (SK-NET FDDI-UP64 DAS) + - SK-5841 (SK-NET FDDI-FP64) + - SK-5843 (SK-NET FDDI-LP64) + - SK-5844 (SK-NET FDDI-LP64 DAS) + - Netelligent 100 FDDI DAS Fibre SC + - Netelligent 100 FDDI SAS Fibre SC + - Netelligent 100 FDDI DAS UTP + - Netelligent 100 FDDI SAS UTP + - Netelligent 100 FDDI SAS Fibre MIC + + Read <file:Documentation/networking/skfp.txt> for information about + the driver. + + Questions concerning this driver can be addressed to: + <linux@syskonnect.de> + + To compile this driver as a module, choose M here: the module + will be called skfp. This is recommended. + +endif # FDDI diff --git a/kernel/drivers/net/fddi/Makefile b/kernel/drivers/net/fddi/Makefile new file mode 100644 index 000000000..36da19c9a --- /dev/null +++ b/kernel/drivers/net/fddi/Makefile @@ -0,0 +1,6 @@ +# +# Makefile for the Linux FDDI network device drivers. +# + +obj-$(CONFIG_DEFXX) += defxx.o +obj-$(CONFIG_SKFP) += skfp/ diff --git a/kernel/drivers/net/fddi/defxx.c b/kernel/drivers/net/fddi/defxx.c new file mode 100644 index 000000000..7f975a2c8 --- /dev/null +++ b/kernel/drivers/net/fddi/defxx.c @@ -0,0 +1,3853 @@ +/* + * File Name: + * defxx.c + * + * Copyright Information: + * Copyright Digital Equipment Corporation 1996. + * + * This software may be used and distributed according to the terms of + * the GNU General Public License, incorporated herein by reference. + * + * Abstract: + * A Linux device driver supporting the Digital Equipment Corporation + * FDDI TURBOchannel, EISA and PCI controller families. Supported + * adapters include: + * + * DEC FDDIcontroller/TURBOchannel (DEFTA) + * DEC FDDIcontroller/EISA (DEFEA) + * DEC FDDIcontroller/PCI (DEFPA) + * + * The original author: + * LVS Lawrence V. Stefani <lstefani@yahoo.com> + * + * Maintainers: + * macro Maciej W. Rozycki <macro@linux-mips.org> + * + * Credits: + * I'd like to thank Patricia Cross for helping me get started with + * Linux, David Davies for a lot of help upgrading and configuring + * my development system and for answering many OS and driver + * development questions, and Alan Cox for recommendations and + * integration help on getting FDDI support into Linux. LVS + * + * Driver Architecture: + * The driver architecture is largely based on previous driver work + * for other operating systems. The upper edge interface and + * functions were largely taken from existing Linux device drivers + * such as David Davies' DE4X5.C driver and Donald Becker's TULIP.C + * driver. + * + * Adapter Probe - + * The driver scans for supported EISA adapters by reading the + * SLOT ID register for each EISA slot and making a match + * against the expected value. + * + * Bus-Specific Initialization - + * This driver currently supports both EISA and PCI controller + * families. While the custom DMA chip and FDDI logic is similar + * or identical, the bus logic is very different. After + * initialization, the only bus-specific differences is in how the + * driver enables and disables interrupts. Other than that, the + * run-time critical code behaves the same on both families. + * It's important to note that both adapter families are configured + * to I/O map, rather than memory map, the adapter registers. + * + * Driver Open/Close - + * In the driver open routine, the driver ISR (interrupt service + * routine) is registered and the adapter is brought to an + * operational state. In the driver close routine, the opposite + * occurs; the driver ISR is deregistered and the adapter is + * brought to a safe, but closed state. Users may use consecutive + * commands to bring the adapter up and down as in the following + * example: + * ifconfig fddi0 up + * ifconfig fddi0 down + * ifconfig fddi0 up + * + * Driver Shutdown - + * Apparently, there is no shutdown or halt routine support under + * Linux. This routine would be called during "reboot" or + * "shutdown" to allow the driver to place the adapter in a safe + * state before a warm reboot occurs. To be really safe, the user + * should close the adapter before shutdown (eg. ifconfig fddi0 down) + * to ensure that the adapter DMA engine is taken off-line. However, + * the current driver code anticipates this problem and always issues + * a soft reset of the adapter at the beginning of driver initialization. + * A future driver enhancement in this area may occur in 2.1.X where + * Alan indicated that a shutdown handler may be implemented. + * + * Interrupt Service Routine - + * The driver supports shared interrupts, so the ISR is registered for + * each board with the appropriate flag and the pointer to that board's + * device structure. This provides the context during interrupt + * processing to support shared interrupts and multiple boards. + * + * Interrupt enabling/disabling can occur at many levels. At the host + * end, you can disable system interrupts, or disable interrupts at the + * PIC (on Intel systems). Across the bus, both EISA and PCI adapters + * have a bus-logic chip interrupt enable/disable as well as a DMA + * controller interrupt enable/disable. + * + * The driver currently enables and disables adapter interrupts at the + * bus-logic chip and assumes that Linux will take care of clearing or + * acknowledging any host-based interrupt chips. + * + * Control Functions - + * Control functions are those used to support functions such as adding + * or deleting multicast addresses, enabling or disabling packet + * reception filters, or other custom/proprietary commands. Presently, + * the driver supports the "get statistics", "set multicast list", and + * "set mac address" functions defined by Linux. A list of possible + * enhancements include: + * + * - Custom ioctl interface for executing port interface commands + * - Custom ioctl interface for adding unicast addresses to + * adapter CAM (to support bridge functions). + * - Custom ioctl interface for supporting firmware upgrades. + * + * Hardware (port interface) Support Routines - + * The driver function names that start with "dfx_hw_" represent + * low-level port interface routines that are called frequently. They + * include issuing a DMA or port control command to the adapter, + * resetting the adapter, or reading the adapter state. Since the + * driver initialization and run-time code must make calls into the + * port interface, these routines were written to be as generic and + * usable as possible. + * + * Receive Path - + * The adapter DMA engine supports a 256 entry receive descriptor block + * of which up to 255 entries can be used at any given time. The + * architecture is a standard producer, consumer, completion model in + * which the driver "produces" receive buffers to the adapter, the + * adapter "consumes" the receive buffers by DMAing incoming packet data, + * and the driver "completes" the receive buffers by servicing the + * incoming packet, then "produces" a new buffer and starts the cycle + * again. Receive buffers can be fragmented in up to 16 fragments + * (descriptor entries). For simplicity, this driver posts + * single-fragment receive buffers of 4608 bytes, then allocates a + * sk_buff, copies the data, then reposts the buffer. To reduce CPU + * utilization, a better approach would be to pass up the receive + * buffer (no extra copy) then allocate and post a replacement buffer. + * This is a performance enhancement that should be looked into at + * some point. + * + * Transmit Path - + * Like the receive path, the adapter DMA engine supports a 256 entry + * transmit descriptor block of which up to 255 entries can be used at + * any given time. Transmit buffers can be fragmented in up to 255 + * fragments (descriptor entries). This driver always posts one + * fragment per transmit packet request. + * + * The fragment contains the entire packet from FC to end of data. + * Before posting the buffer to the adapter, the driver sets a three-byte + * packet request header (PRH) which is required by the Motorola MAC chip + * used on the adapters. The PRH tells the MAC the type of token to + * receive/send, whether or not to generate and append the CRC, whether + * synchronous or asynchronous framing is used, etc. Since the PRH + * definition is not necessarily consistent across all FDDI chipsets, + * the driver, rather than the common FDDI packet handler routines, + * sets these bytes. + * + * To reduce the amount of descriptor fetches needed per transmit request, + * the driver takes advantage of the fact that there are at least three + * bytes available before the skb->data field on the outgoing transmit + * request. This is guaranteed by having fddi_setup() in net_init.c set + * dev->hard_header_len to 24 bytes. 21 bytes accounts for the largest + * header in an 802.2 SNAP frame. The other 3 bytes are the extra "pad" + * bytes which we'll use to store the PRH. + * + * There's a subtle advantage to adding these pad bytes to the + * hard_header_len, it ensures that the data portion of the packet for + * an 802.2 SNAP frame is longword aligned. Other FDDI driver + * implementations may not need the extra padding and can start copying + * or DMAing directly from the FC byte which starts at skb->data. Should + * another driver implementation need ADDITIONAL padding, the net_init.c + * module should be updated and dev->hard_header_len should be increased. + * NOTE: To maintain the alignment on the data portion of the packet, + * dev->hard_header_len should always be evenly divisible by 4 and at + * least 24 bytes in size. + * + * Modification History: + * Date Name Description + * 16-Aug-96 LVS Created. + * 20-Aug-96 LVS Updated dfx_probe so that version information + * string is only displayed if 1 or more cards are + * found. Changed dfx_rcv_queue_process to copy + * 3 NULL bytes before FC to ensure that data is + * longword aligned in receive buffer. + * 09-Sep-96 LVS Updated dfx_ctl_set_multicast_list to enable + * LLC group promiscuous mode if multicast list + * is too large. LLC individual/group promiscuous + * mode is now disabled if IFF_PROMISC flag not set. + * dfx_xmt_queue_pkt no longer checks for NULL skb + * on Alan Cox recommendation. Added node address + * override support. + * 12-Sep-96 LVS Reset current address to factory address during + * device open. Updated transmit path to post a + * single fragment which includes PRH->end of data. + * Mar 2000 AC Did various cleanups for 2.3.x + * Jun 2000 jgarzik PCI and resource alloc cleanups + * Jul 2000 tjeerd Much cleanup and some bug fixes + * Sep 2000 tjeerd Fix leak on unload, cosmetic code cleanup + * Feb 2001 Skb allocation fixes + * Feb 2001 davej PCI enable cleanups. + * 04 Aug 2003 macro Converted to the DMA API. + * 14 Aug 2004 macro Fix device names reported. + * 14 Jun 2005 macro Use irqreturn_t. + * 23 Oct 2006 macro Big-endian host support. + * 14 Dec 2006 macro TURBOchannel support. + * 01 Jul 2014 macro Fixes for DMA on 64-bit hosts. + */ + +/* Include files */ +#include <linux/bitops.h> +#include <linux/compiler.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/eisa.h> +#include <linux/errno.h> +#include <linux/fddidevice.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/pci.h> +#include <linux/skbuff.h> +#include <linux/slab.h> +#include <linux/string.h> +#include <linux/tc.h> + +#include <asm/byteorder.h> +#include <asm/io.h> + +#include "defxx.h" + +/* Version information string should be updated prior to each new release! */ +#define DRV_NAME "defxx" +#define DRV_VERSION "v1.11" +#define DRV_RELDATE "2014/07/01" + +static char version[] = + DRV_NAME ": " DRV_VERSION " " DRV_RELDATE + " Lawrence V. Stefani and others\n"; + +#define DYNAMIC_BUFFERS 1 + +#define SKBUFF_RX_COPYBREAK 200 +/* + * NEW_SKB_SIZE = PI_RCV_DATA_K_SIZE_MAX+128 to allow 128 byte + * alignment for compatibility with old EISA boards. + */ +#define NEW_SKB_SIZE (PI_RCV_DATA_K_SIZE_MAX+128) + +#ifdef CONFIG_EISA +#define DFX_BUS_EISA(dev) (dev->bus == &eisa_bus_type) +#else +#define DFX_BUS_EISA(dev) 0 +#endif + +#ifdef CONFIG_TC +#define DFX_BUS_TC(dev) (dev->bus == &tc_bus_type) +#else +#define DFX_BUS_TC(dev) 0 +#endif + +#ifdef CONFIG_DEFXX_MMIO +#define DFX_MMIO 1 +#else +#define DFX_MMIO 0 +#endif + +/* Define module-wide (static) routines */ + +static void dfx_bus_init(struct net_device *dev); +static void dfx_bus_uninit(struct net_device *dev); +static void dfx_bus_config_check(DFX_board_t *bp); + +static int dfx_driver_init(struct net_device *dev, + const char *print_name, + resource_size_t bar_start); +static int dfx_adap_init(DFX_board_t *bp, int get_buffers); + +static int dfx_open(struct net_device *dev); +static int dfx_close(struct net_device *dev); + +static void dfx_int_pr_halt_id(DFX_board_t *bp); +static void dfx_int_type_0_process(DFX_board_t *bp); +static void dfx_int_common(struct net_device *dev); +static irqreturn_t dfx_interrupt(int irq, void *dev_id); + +static struct net_device_stats *dfx_ctl_get_stats(struct net_device *dev); +static void dfx_ctl_set_multicast_list(struct net_device *dev); +static int dfx_ctl_set_mac_address(struct net_device *dev, void *addr); +static int dfx_ctl_update_cam(DFX_board_t *bp); +static int dfx_ctl_update_filters(DFX_board_t *bp); + +static int dfx_hw_dma_cmd_req(DFX_board_t *bp); +static int dfx_hw_port_ctrl_req(DFX_board_t *bp, PI_UINT32 command, PI_UINT32 data_a, PI_UINT32 data_b, PI_UINT32 *host_data); +static void dfx_hw_adap_reset(DFX_board_t *bp, PI_UINT32 type); +static int dfx_hw_adap_state_rd(DFX_board_t *bp); +static int dfx_hw_dma_uninit(DFX_board_t *bp, PI_UINT32 type); + +static int dfx_rcv_init(DFX_board_t *bp, int get_buffers); +static void dfx_rcv_queue_process(DFX_board_t *bp); +#ifdef DYNAMIC_BUFFERS +static void dfx_rcv_flush(DFX_board_t *bp); +#else +static inline void dfx_rcv_flush(DFX_board_t *bp) {} +#endif + +static netdev_tx_t dfx_xmt_queue_pkt(struct sk_buff *skb, + struct net_device *dev); +static int dfx_xmt_done(DFX_board_t *bp); +static void dfx_xmt_flush(DFX_board_t *bp); + +/* Define module-wide (static) variables */ + +static struct pci_driver dfx_pci_driver; +static struct eisa_driver dfx_eisa_driver; +static struct tc_driver dfx_tc_driver; + + +/* + * ======================= + * = dfx_port_write_long = + * = dfx_port_read_long = + * ======================= + * + * Overview: + * Routines for reading and writing values from/to adapter + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * offset - register offset from base I/O address + * data - for dfx_port_write_long, this is a value to write; + * for dfx_port_read_long, this is a pointer to store + * the read value + * + * Functional Description: + * These routines perform the correct operation to read or write + * the adapter register. + * + * EISA port block base addresses are based on the slot number in which the + * controller is installed. For example, if the EISA controller is installed + * in slot 4, the port block base address is 0x4000. If the controller is + * installed in slot 2, the port block base address is 0x2000, and so on. + * This port block can be used to access PDQ, ESIC, and DEFEA on-board + * registers using the register offsets defined in DEFXX.H. + * + * PCI port block base addresses are assigned by the PCI BIOS or system + * firmware. There is one 128 byte port block which can be accessed. It + * allows for I/O mapping of both PDQ and PFI registers using the register + * offsets defined in DEFXX.H. + * + * Return Codes: + * None + * + * Assumptions: + * bp->base is a valid base I/O address for this adapter. + * offset is a valid register offset for this adapter. + * + * Side Effects: + * Rather than produce macros for these functions, these routines + * are defined using "inline" to ensure that the compiler will + * generate inline code and not waste a procedure call and return. + * This provides all the benefits of macros, but with the + * advantage of strict data type checking. + */ + +static inline void dfx_writel(DFX_board_t *bp, int offset, u32 data) +{ + writel(data, bp->base.mem + offset); + mb(); +} + +static inline void dfx_outl(DFX_board_t *bp, int offset, u32 data) +{ + outl(data, bp->base.port + offset); +} + +static void dfx_port_write_long(DFX_board_t *bp, int offset, u32 data) +{ + struct device __maybe_unused *bdev = bp->bus_dev; + int dfx_bus_tc = DFX_BUS_TC(bdev); + int dfx_use_mmio = DFX_MMIO || dfx_bus_tc; + + if (dfx_use_mmio) + dfx_writel(bp, offset, data); + else + dfx_outl(bp, offset, data); +} + + +static inline void dfx_readl(DFX_board_t *bp, int offset, u32 *data) +{ + mb(); + *data = readl(bp->base.mem + offset); +} + +static inline void dfx_inl(DFX_board_t *bp, int offset, u32 *data) +{ + *data = inl(bp->base.port + offset); +} + +static void dfx_port_read_long(DFX_board_t *bp, int offset, u32 *data) +{ + struct device __maybe_unused *bdev = bp->bus_dev; + int dfx_bus_tc = DFX_BUS_TC(bdev); + int dfx_use_mmio = DFX_MMIO || dfx_bus_tc; + + if (dfx_use_mmio) + dfx_readl(bp, offset, data); + else + dfx_inl(bp, offset, data); +} + + +/* + * ================ + * = dfx_get_bars = + * ================ + * + * Overview: + * Retrieves the address ranges used to access control and status + * registers. + * + * Returns: + * None + * + * Arguments: + * bdev - pointer to device information + * bar_start - pointer to store the start addresses + * bar_len - pointer to store the lengths of the areas + * + * Assumptions: + * I am sure there are some. + * + * Side Effects: + * None + */ +static void dfx_get_bars(struct device *bdev, + resource_size_t *bar_start, resource_size_t *bar_len) +{ + int dfx_bus_pci = dev_is_pci(bdev); + int dfx_bus_eisa = DFX_BUS_EISA(bdev); + int dfx_bus_tc = DFX_BUS_TC(bdev); + int dfx_use_mmio = DFX_MMIO || dfx_bus_tc; + + if (dfx_bus_pci) { + int num = dfx_use_mmio ? 0 : 1; + + bar_start[0] = pci_resource_start(to_pci_dev(bdev), num); + bar_len[0] = pci_resource_len(to_pci_dev(bdev), num); + bar_start[2] = bar_start[1] = 0; + bar_len[2] = bar_len[1] = 0; + } + if (dfx_bus_eisa) { + unsigned long base_addr = to_eisa_device(bdev)->base_addr; + resource_size_t bar_lo; + resource_size_t bar_hi; + + if (dfx_use_mmio) { + bar_lo = inb(base_addr + PI_ESIC_K_MEM_ADD_LO_CMP_2); + bar_lo <<= 8; + bar_lo |= inb(base_addr + PI_ESIC_K_MEM_ADD_LO_CMP_1); + bar_lo <<= 8; + bar_lo |= inb(base_addr + PI_ESIC_K_MEM_ADD_LO_CMP_0); + bar_lo <<= 8; + bar_start[0] = bar_lo; + bar_hi = inb(base_addr + PI_ESIC_K_MEM_ADD_HI_CMP_2); + bar_hi <<= 8; + bar_hi |= inb(base_addr + PI_ESIC_K_MEM_ADD_HI_CMP_1); + bar_hi <<= 8; + bar_hi |= inb(base_addr + PI_ESIC_K_MEM_ADD_HI_CMP_0); + bar_hi <<= 8; + bar_len[0] = ((bar_hi - bar_lo) | PI_MEM_ADD_MASK_M) + + 1; + } else { + bar_start[0] = base_addr; + bar_len[0] = PI_ESIC_K_CSR_IO_LEN; + } + bar_start[1] = base_addr + PI_DEFEA_K_BURST_HOLDOFF; + bar_len[1] = PI_ESIC_K_BURST_HOLDOFF_LEN; + bar_start[2] = base_addr + PI_ESIC_K_ESIC_CSR; + bar_len[2] = PI_ESIC_K_ESIC_CSR_LEN; + } + if (dfx_bus_tc) { + bar_start[0] = to_tc_dev(bdev)->resource.start + + PI_TC_K_CSR_OFFSET; + bar_len[0] = PI_TC_K_CSR_LEN; + bar_start[2] = bar_start[1] = 0; + bar_len[2] = bar_len[1] = 0; + } +} + +static const struct net_device_ops dfx_netdev_ops = { + .ndo_open = dfx_open, + .ndo_stop = dfx_close, + .ndo_start_xmit = dfx_xmt_queue_pkt, + .ndo_get_stats = dfx_ctl_get_stats, + .ndo_set_rx_mode = dfx_ctl_set_multicast_list, + .ndo_set_mac_address = dfx_ctl_set_mac_address, +}; + +/* + * ================ + * = dfx_register = + * ================ + * + * Overview: + * Initializes a supported FDDI controller + * + * Returns: + * Condition code + * + * Arguments: + * bdev - pointer to device information + * + * Functional Description: + * + * Return Codes: + * 0 - This device (fddi0, fddi1, etc) configured successfully + * -EBUSY - Failed to get resources, or dfx_driver_init failed. + * + * Assumptions: + * It compiles so it should work :-( (PCI cards do :-) + * + * Side Effects: + * Device structures for FDDI adapters (fddi0, fddi1, etc) are + * initialized and the board resources are read and stored in + * the device structure. + */ +static int dfx_register(struct device *bdev) +{ + static int version_disp; + int dfx_bus_pci = dev_is_pci(bdev); + int dfx_bus_eisa = DFX_BUS_EISA(bdev); + int dfx_bus_tc = DFX_BUS_TC(bdev); + int dfx_use_mmio = DFX_MMIO || dfx_bus_tc; + const char *print_name = dev_name(bdev); + struct net_device *dev; + DFX_board_t *bp; /* board pointer */ + resource_size_t bar_start[3]; /* pointers to ports */ + resource_size_t bar_len[3]; /* resource length */ + int alloc_size; /* total buffer size used */ + struct resource *region; + int err = 0; + + if (!version_disp) { /* display version info if adapter is found */ + version_disp = 1; /* set display flag to TRUE so that */ + printk(version); /* we only display this string ONCE */ + } + + dev = alloc_fddidev(sizeof(*bp)); + if (!dev) { + printk(KERN_ERR "%s: Unable to allocate fddidev, aborting\n", + print_name); + return -ENOMEM; + } + + /* Enable PCI device. */ + if (dfx_bus_pci) { + err = pci_enable_device(to_pci_dev(bdev)); + if (err) { + pr_err("%s: Cannot enable PCI device, aborting\n", + print_name); + goto err_out; + } + } + + SET_NETDEV_DEV(dev, bdev); + + bp = netdev_priv(dev); + bp->bus_dev = bdev; + dev_set_drvdata(bdev, dev); + + dfx_get_bars(bdev, bar_start, bar_len); + if (dfx_bus_eisa && dfx_use_mmio && bar_start[0] == 0) { + pr_err("%s: Cannot use MMIO, no address set, aborting\n", + print_name); + pr_err("%s: Run ECU and set adapter's MMIO location\n", + print_name); + pr_err("%s: Or recompile driver with \"CONFIG_DEFXX_MMIO=n\"" + "\n", print_name); + err = -ENXIO; + goto err_out; + } + + if (dfx_use_mmio) + region = request_mem_region(bar_start[0], bar_len[0], + print_name); + else + region = request_region(bar_start[0], bar_len[0], print_name); + if (!region) { + pr_err("%s: Cannot reserve %s resource 0x%lx @ 0x%lx, " + "aborting\n", dfx_use_mmio ? "MMIO" : "I/O", print_name, + (long)bar_len[0], (long)bar_start[0]); + err = -EBUSY; + goto err_out_disable; + } + if (bar_start[1] != 0) { + region = request_region(bar_start[1], bar_len[1], print_name); + if (!region) { + pr_err("%s: Cannot reserve I/O resource " + "0x%lx @ 0x%lx, aborting\n", print_name, + (long)bar_len[1], (long)bar_start[1]); + err = -EBUSY; + goto err_out_csr_region; + } + } + if (bar_start[2] != 0) { + region = request_region(bar_start[2], bar_len[2], print_name); + if (!region) { + pr_err("%s: Cannot reserve I/O resource " + "0x%lx @ 0x%lx, aborting\n", print_name, + (long)bar_len[2], (long)bar_start[2]); + err = -EBUSY; + goto err_out_bh_region; + } + } + + /* Set up I/O base address. */ + if (dfx_use_mmio) { + bp->base.mem = ioremap_nocache(bar_start[0], bar_len[0]); + if (!bp->base.mem) { + printk(KERN_ERR "%s: Cannot map MMIO\n", print_name); + err = -ENOMEM; + goto err_out_esic_region; + } + } else { + bp->base.port = bar_start[0]; + dev->base_addr = bar_start[0]; + } + + /* Initialize new device structure */ + dev->netdev_ops = &dfx_netdev_ops; + + if (dfx_bus_pci) + pci_set_master(to_pci_dev(bdev)); + + if (dfx_driver_init(dev, print_name, bar_start[0]) != DFX_K_SUCCESS) { + err = -ENODEV; + goto err_out_unmap; + } + + err = register_netdev(dev); + if (err) + goto err_out_kfree; + + printk("%s: registered as %s\n", print_name, dev->name); + return 0; + +err_out_kfree: + alloc_size = sizeof(PI_DESCR_BLOCK) + + PI_CMD_REQ_K_SIZE_MAX + PI_CMD_RSP_K_SIZE_MAX + +#ifndef DYNAMIC_BUFFERS + (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) + +#endif + sizeof(PI_CONSUMER_BLOCK) + + (PI_ALIGN_K_DESC_BLK - 1); + if (bp->kmalloced) + dma_free_coherent(bdev, alloc_size, + bp->kmalloced, bp->kmalloced_dma); + +err_out_unmap: + if (dfx_use_mmio) + iounmap(bp->base.mem); + +err_out_esic_region: + if (bar_start[2] != 0) + release_region(bar_start[2], bar_len[2]); + +err_out_bh_region: + if (bar_start[1] != 0) + release_region(bar_start[1], bar_len[1]); + +err_out_csr_region: + if (dfx_use_mmio) + release_mem_region(bar_start[0], bar_len[0]); + else + release_region(bar_start[0], bar_len[0]); + +err_out_disable: + if (dfx_bus_pci) + pci_disable_device(to_pci_dev(bdev)); + +err_out: + free_netdev(dev); + return err; +} + + +/* + * ================ + * = dfx_bus_init = + * ================ + * + * Overview: + * Initializes the bus-specific controller logic. + * + * Returns: + * None + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * Determine and save adapter IRQ in device table, + * then perform bus-specific logic initialization. + * + * Return Codes: + * None + * + * Assumptions: + * bp->base has already been set with the proper + * base I/O address for this device. + * + * Side Effects: + * Interrupts are enabled at the adapter bus-specific logic. + * Note: Interrupts at the DMA engine (PDQ chip) are not + * enabled yet. + */ + +static void dfx_bus_init(struct net_device *dev) +{ + DFX_board_t *bp = netdev_priv(dev); + struct device *bdev = bp->bus_dev; + int dfx_bus_pci = dev_is_pci(bdev); + int dfx_bus_eisa = DFX_BUS_EISA(bdev); + int dfx_bus_tc = DFX_BUS_TC(bdev); + int dfx_use_mmio = DFX_MMIO || dfx_bus_tc; + u8 val; + + DBG_printk("In dfx_bus_init...\n"); + + /* Initialize a pointer back to the net_device struct */ + bp->dev = dev; + + /* Initialize adapter based on bus type */ + + if (dfx_bus_tc) + dev->irq = to_tc_dev(bdev)->interrupt; + if (dfx_bus_eisa) { + unsigned long base_addr = to_eisa_device(bdev)->base_addr; + + /* Disable the board before fiddling with the decoders. */ + outb(0, base_addr + PI_ESIC_K_SLOT_CNTRL); + + /* Get the interrupt level from the ESIC chip. */ + val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + val &= PI_CONFIG_STAT_0_M_IRQ; + val >>= PI_CONFIG_STAT_0_V_IRQ; + + switch (val) { + case PI_CONFIG_STAT_0_IRQ_K_9: + dev->irq = 9; + break; + + case PI_CONFIG_STAT_0_IRQ_K_10: + dev->irq = 10; + break; + + case PI_CONFIG_STAT_0_IRQ_K_11: + dev->irq = 11; + break; + + case PI_CONFIG_STAT_0_IRQ_K_15: + dev->irq = 15; + break; + } + + /* + * Enable memory decoding (MEMCS1) and/or port decoding + * (IOCS1/IOCS0) as appropriate in Function Control + * Register. MEMCS1 or IOCS0 is used for PDQ registers, + * taking 16 32-bit words, while IOCS1 is used for the + * Burst Holdoff register, taking a single 32-bit word + * only. We use the slot-specific I/O range as per the + * ESIC spec, that is set bits 15:12 in the mask registers + * to mask them out. + */ + + /* Set the decode range of the board. */ + val = 0; + outb(val, base_addr + PI_ESIC_K_IO_ADD_CMP_0_1); + val = PI_DEFEA_K_CSR_IO; + outb(val, base_addr + PI_ESIC_K_IO_ADD_CMP_0_0); + + val = PI_IO_CMP_M_SLOT; + outb(val, base_addr + PI_ESIC_K_IO_ADD_MASK_0_1); + val = (PI_ESIC_K_CSR_IO_LEN - 1) & ~3; + outb(val, base_addr + PI_ESIC_K_IO_ADD_MASK_0_0); + + val = 0; + outb(val, base_addr + PI_ESIC_K_IO_ADD_CMP_1_1); + val = PI_DEFEA_K_BURST_HOLDOFF; + outb(val, base_addr + PI_ESIC_K_IO_ADD_CMP_1_0); + + val = PI_IO_CMP_M_SLOT; + outb(val, base_addr + PI_ESIC_K_IO_ADD_MASK_1_1); + val = (PI_ESIC_K_BURST_HOLDOFF_LEN - 1) & ~3; + outb(val, base_addr + PI_ESIC_K_IO_ADD_MASK_1_0); + + /* Enable the decoders. */ + val = PI_FUNCTION_CNTRL_M_IOCS1; + if (dfx_use_mmio) + val |= PI_FUNCTION_CNTRL_M_MEMCS1; + else + val |= PI_FUNCTION_CNTRL_M_IOCS0; + outb(val, base_addr + PI_ESIC_K_FUNCTION_CNTRL); + + /* + * Enable access to the rest of the module + * (including PDQ and packet memory). + */ + val = PI_SLOT_CNTRL_M_ENB; + outb(val, base_addr + PI_ESIC_K_SLOT_CNTRL); + + /* + * Map PDQ registers into memory or port space. This is + * done with a bit in the Burst Holdoff register. + */ + val = inb(base_addr + PI_DEFEA_K_BURST_HOLDOFF); + if (dfx_use_mmio) + val |= PI_BURST_HOLDOFF_M_MEM_MAP; + else + val &= ~PI_BURST_HOLDOFF_M_MEM_MAP; + outb(val, base_addr + PI_DEFEA_K_BURST_HOLDOFF); + + /* Enable interrupts at EISA bus interface chip (ESIC) */ + val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + val |= PI_CONFIG_STAT_0_M_INT_ENB; + outb(val, base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + } + if (dfx_bus_pci) { + struct pci_dev *pdev = to_pci_dev(bdev); + + /* Get the interrupt level from the PCI Configuration Table */ + + dev->irq = pdev->irq; + + /* Check Latency Timer and set if less than minimal */ + + pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &val); + if (val < PFI_K_LAT_TIMER_MIN) { + val = PFI_K_LAT_TIMER_DEF; + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, val); + } + + /* Enable interrupts at PCI bus interface chip (PFI) */ + val = PFI_MODE_M_PDQ_INT_ENB | PFI_MODE_M_DMA_ENB; + dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, val); + } +} + +/* + * ================== + * = dfx_bus_uninit = + * ================== + * + * Overview: + * Uninitializes the bus-specific controller logic. + * + * Returns: + * None + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * Perform bus-specific logic uninitialization. + * + * Return Codes: + * None + * + * Assumptions: + * bp->base has already been set with the proper + * base I/O address for this device. + * + * Side Effects: + * Interrupts are disabled at the adapter bus-specific logic. + */ + +static void dfx_bus_uninit(struct net_device *dev) +{ + DFX_board_t *bp = netdev_priv(dev); + struct device *bdev = bp->bus_dev; + int dfx_bus_pci = dev_is_pci(bdev); + int dfx_bus_eisa = DFX_BUS_EISA(bdev); + u8 val; + + DBG_printk("In dfx_bus_uninit...\n"); + + /* Uninitialize adapter based on bus type */ + + if (dfx_bus_eisa) { + unsigned long base_addr = to_eisa_device(bdev)->base_addr; + + /* Disable interrupts at EISA bus interface chip (ESIC) */ + val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + val &= ~PI_CONFIG_STAT_0_M_INT_ENB; + outb(val, base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + + /* Disable the board. */ + outb(0, base_addr + PI_ESIC_K_SLOT_CNTRL); + + /* Disable memory and port decoders. */ + outb(0, base_addr + PI_ESIC_K_FUNCTION_CNTRL); + } + if (dfx_bus_pci) { + /* Disable interrupts at PCI bus interface chip (PFI) */ + dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, 0); + } +} + + +/* + * ======================== + * = dfx_bus_config_check = + * ======================== + * + * Overview: + * Checks the configuration (burst size, full-duplex, etc.) If any parameters + * are illegal, then this routine will set new defaults. + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * For Revision 1 FDDI EISA, Revision 2 or later FDDI EISA with rev E or later + * PDQ, and all FDDI PCI controllers, all values are legal. + * + * Return Codes: + * None + * + * Assumptions: + * dfx_adap_init has NOT been called yet so burst size and other items have + * not been set. + * + * Side Effects: + * None + */ + +static void dfx_bus_config_check(DFX_board_t *bp) +{ + struct device __maybe_unused *bdev = bp->bus_dev; + int dfx_bus_eisa = DFX_BUS_EISA(bdev); + int status; /* return code from adapter port control call */ + u32 host_data; /* LW data returned from port control call */ + + DBG_printk("In dfx_bus_config_check...\n"); + + /* Configuration check only valid for EISA adapter */ + + if (dfx_bus_eisa) { + /* + * First check if revision 2 EISA controller. Rev. 1 cards used + * PDQ revision B, so no workaround needed in this case. Rev. 3 + * cards used PDQ revision E, so no workaround needed in this + * case, either. Only Rev. 2 cards used either Rev. D or E + * chips, so we must verify the chip revision on Rev. 2 cards. + */ + if (to_eisa_device(bdev)->id.driver_data == DEFEA_PROD_ID_2) { + /* + * Revision 2 FDDI EISA controller found, + * so let's check PDQ revision of adapter. + */ + status = dfx_hw_port_ctrl_req(bp, + PI_PCTRL_M_SUB_CMD, + PI_SUB_CMD_K_PDQ_REV_GET, + 0, + &host_data); + if ((status != DFX_K_SUCCESS) || (host_data == 2)) + { + /* + * Either we couldn't determine the PDQ revision, or + * we determined that it is at revision D. In either case, + * we need to implement the workaround. + */ + + /* Ensure that the burst size is set to 8 longwords or less */ + + switch (bp->burst_size) + { + case PI_PDATA_B_DMA_BURST_SIZE_32: + case PI_PDATA_B_DMA_BURST_SIZE_16: + bp->burst_size = PI_PDATA_B_DMA_BURST_SIZE_8; + break; + + default: + break; + } + + /* Ensure that full-duplex mode is not enabled */ + + bp->full_duplex_enb = PI_SNMP_K_FALSE; + } + } + } + } + + +/* + * =================== + * = dfx_driver_init = + * =================== + * + * Overview: + * Initializes remaining adapter board structure information + * and makes sure adapter is in a safe state prior to dfx_open(). + * + * Returns: + * Condition code + * + * Arguments: + * dev - pointer to device information + * print_name - printable device name + * + * Functional Description: + * This function allocates additional resources such as the host memory + * blocks needed by the adapter (eg. descriptor and consumer blocks). + * Remaining bus initialization steps are also completed. The adapter + * is also reset so that it is in the DMA_UNAVAILABLE state. The OS + * must call dfx_open() to open the adapter and bring it on-line. + * + * Return Codes: + * DFX_K_SUCCESS - initialization succeeded + * DFX_K_FAILURE - initialization failed - could not allocate memory + * or read adapter MAC address + * + * Assumptions: + * Memory allocated from pci_alloc_consistent() call is physically + * contiguous, locked memory. + * + * Side Effects: + * Adapter is reset and should be in DMA_UNAVAILABLE state before + * returning from this routine. + */ + +static int dfx_driver_init(struct net_device *dev, const char *print_name, + resource_size_t bar_start) +{ + DFX_board_t *bp = netdev_priv(dev); + struct device *bdev = bp->bus_dev; + int dfx_bus_pci = dev_is_pci(bdev); + int dfx_bus_eisa = DFX_BUS_EISA(bdev); + int dfx_bus_tc = DFX_BUS_TC(bdev); + int dfx_use_mmio = DFX_MMIO || dfx_bus_tc; + int alloc_size; /* total buffer size needed */ + char *top_v, *curr_v; /* virtual addrs into memory block */ + dma_addr_t top_p, curr_p; /* physical addrs into memory block */ + u32 data; /* host data register value */ + __le32 le32; + char *board_name = NULL; + + DBG_printk("In dfx_driver_init...\n"); + + /* Initialize bus-specific hardware registers */ + + dfx_bus_init(dev); + + /* + * Initialize default values for configurable parameters + * + * Note: All of these parameters are ones that a user may + * want to customize. It'd be nice to break these + * out into Space.c or someplace else that's more + * accessible/understandable than this file. + */ + + bp->full_duplex_enb = PI_SNMP_K_FALSE; + bp->req_ttrt = 8 * 12500; /* 8ms in 80 nanosec units */ + bp->burst_size = PI_PDATA_B_DMA_BURST_SIZE_DEF; + bp->rcv_bufs_to_post = RCV_BUFS_DEF; + + /* + * Ensure that HW configuration is OK + * + * Note: Depending on the hardware revision, we may need to modify + * some of the configurable parameters to workaround hardware + * limitations. We'll perform this configuration check AFTER + * setting the parameters to their default values. + */ + + dfx_bus_config_check(bp); + + /* Disable PDQ interrupts first */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS); + + /* Place adapter in DMA_UNAVAILABLE state by resetting adapter */ + + (void) dfx_hw_dma_uninit(bp, PI_PDATA_A_RESET_M_SKIP_ST); + + /* Read the factory MAC address from the adapter then save it */ + + if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_LO, 0, + &data) != DFX_K_SUCCESS) { + printk("%s: Could not read adapter factory MAC address!\n", + print_name); + return DFX_K_FAILURE; + } + le32 = cpu_to_le32(data); + memcpy(&bp->factory_mac_addr[0], &le32, sizeof(u32)); + + if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_HI, 0, + &data) != DFX_K_SUCCESS) { + printk("%s: Could not read adapter factory MAC address!\n", + print_name); + return DFX_K_FAILURE; + } + le32 = cpu_to_le32(data); + memcpy(&bp->factory_mac_addr[4], &le32, sizeof(u16)); + + /* + * Set current address to factory address + * + * Note: Node address override support is handled through + * dfx_ctl_set_mac_address. + */ + + memcpy(dev->dev_addr, bp->factory_mac_addr, FDDI_K_ALEN); + if (dfx_bus_tc) + board_name = "DEFTA"; + if (dfx_bus_eisa) + board_name = "DEFEA"; + if (dfx_bus_pci) + board_name = "DEFPA"; + pr_info("%s: %s at %s addr = 0x%llx, IRQ = %d, Hardware addr = %pMF\n", + print_name, board_name, dfx_use_mmio ? "MMIO" : "I/O", + (long long)bar_start, dev->irq, dev->dev_addr); + + /* + * Get memory for descriptor block, consumer block, and other buffers + * that need to be DMA read or written to by the adapter. + */ + + alloc_size = sizeof(PI_DESCR_BLOCK) + + PI_CMD_REQ_K_SIZE_MAX + + PI_CMD_RSP_K_SIZE_MAX + +#ifndef DYNAMIC_BUFFERS + (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) + +#endif + sizeof(PI_CONSUMER_BLOCK) + + (PI_ALIGN_K_DESC_BLK - 1); + bp->kmalloced = top_v = dma_zalloc_coherent(bp->bus_dev, alloc_size, + &bp->kmalloced_dma, + GFP_ATOMIC); + if (top_v == NULL) + return DFX_K_FAILURE; + + top_p = bp->kmalloced_dma; /* get physical address of buffer */ + + /* + * To guarantee the 8K alignment required for the descriptor block, 8K - 1 + * plus the amount of memory needed was allocated. The physical address + * is now 8K aligned. By carving up the memory in a specific order, + * we'll guarantee the alignment requirements for all other structures. + * + * Note: If the assumptions change regarding the non-paged, non-cached, + * physically contiguous nature of the memory block or the address + * alignments, then we'll need to implement a different algorithm + * for allocating the needed memory. + */ + + curr_p = ALIGN(top_p, PI_ALIGN_K_DESC_BLK); + curr_v = top_v + (curr_p - top_p); + + /* Reserve space for descriptor block */ + + bp->descr_block_virt = (PI_DESCR_BLOCK *) curr_v; + bp->descr_block_phys = curr_p; + curr_v += sizeof(PI_DESCR_BLOCK); + curr_p += sizeof(PI_DESCR_BLOCK); + + /* Reserve space for command request buffer */ + + bp->cmd_req_virt = (PI_DMA_CMD_REQ *) curr_v; + bp->cmd_req_phys = curr_p; + curr_v += PI_CMD_REQ_K_SIZE_MAX; + curr_p += PI_CMD_REQ_K_SIZE_MAX; + + /* Reserve space for command response buffer */ + + bp->cmd_rsp_virt = (PI_DMA_CMD_RSP *) curr_v; + bp->cmd_rsp_phys = curr_p; + curr_v += PI_CMD_RSP_K_SIZE_MAX; + curr_p += PI_CMD_RSP_K_SIZE_MAX; + + /* Reserve space for the LLC host receive queue buffers */ + + bp->rcv_block_virt = curr_v; + bp->rcv_block_phys = curr_p; + +#ifndef DYNAMIC_BUFFERS + curr_v += (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX); + curr_p += (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX); +#endif + + /* Reserve space for the consumer block */ + + bp->cons_block_virt = (PI_CONSUMER_BLOCK *) curr_v; + bp->cons_block_phys = curr_p; + + /* Display virtual and physical addresses if debug driver */ + + DBG_printk("%s: Descriptor block virt = %p, phys = %pad\n", + print_name, bp->descr_block_virt, &bp->descr_block_phys); + DBG_printk("%s: Command Request buffer virt = %p, phys = %pad\n", + print_name, bp->cmd_req_virt, &bp->cmd_req_phys); + DBG_printk("%s: Command Response buffer virt = %p, phys = %pad\n", + print_name, bp->cmd_rsp_virt, &bp->cmd_rsp_phys); + DBG_printk("%s: Receive buffer block virt = %p, phys = %pad\n", + print_name, bp->rcv_block_virt, &bp->rcv_block_phys); + DBG_printk("%s: Consumer block virt = %p, phys = %pad\n", + print_name, bp->cons_block_virt, &bp->cons_block_phys); + + return DFX_K_SUCCESS; +} + + +/* + * ================= + * = dfx_adap_init = + * ================= + * + * Overview: + * Brings the adapter to the link avail/link unavailable state. + * + * Returns: + * Condition code + * + * Arguments: + * bp - pointer to board information + * get_buffers - non-zero if buffers to be allocated + * + * Functional Description: + * Issues the low-level firmware/hardware calls necessary to bring + * the adapter up, or to properly reset and restore adapter during + * run-time. + * + * Return Codes: + * DFX_K_SUCCESS - Adapter brought up successfully + * DFX_K_FAILURE - Adapter initialization failed + * + * Assumptions: + * bp->reset_type should be set to a valid reset type value before + * calling this routine. + * + * Side Effects: + * Adapter should be in LINK_AVAILABLE or LINK_UNAVAILABLE state + * upon a successful return of this routine. + */ + +static int dfx_adap_init(DFX_board_t *bp, int get_buffers) + { + DBG_printk("In dfx_adap_init...\n"); + + /* Disable PDQ interrupts first */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS); + + /* Place adapter in DMA_UNAVAILABLE state by resetting adapter */ + + if (dfx_hw_dma_uninit(bp, bp->reset_type) != DFX_K_SUCCESS) + { + printk("%s: Could not uninitialize/reset adapter!\n", bp->dev->name); + return DFX_K_FAILURE; + } + + /* + * When the PDQ is reset, some false Type 0 interrupts may be pending, + * so we'll acknowledge all Type 0 interrupts now before continuing. + */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, PI_HOST_INT_K_ACK_ALL_TYPE_0); + + /* + * Clear Type 1 and Type 2 registers before going to DMA_AVAILABLE state + * + * Note: We only need to clear host copies of these registers. The PDQ reset + * takes care of the on-board register values. + */ + + bp->cmd_req_reg.lword = 0; + bp->cmd_rsp_reg.lword = 0; + bp->rcv_xmt_reg.lword = 0; + + /* Clear consumer block before going to DMA_AVAILABLE state */ + + memset(bp->cons_block_virt, 0, sizeof(PI_CONSUMER_BLOCK)); + + /* Initialize the DMA Burst Size */ + + if (dfx_hw_port_ctrl_req(bp, + PI_PCTRL_M_SUB_CMD, + PI_SUB_CMD_K_BURST_SIZE_SET, + bp->burst_size, + NULL) != DFX_K_SUCCESS) + { + printk("%s: Could not set adapter burst size!\n", bp->dev->name); + return DFX_K_FAILURE; + } + + /* + * Set base address of Consumer Block + * + * Assumption: 32-bit physical address of consumer block is 64 byte + * aligned. That is, bits 0-5 of the address must be zero. + */ + + if (dfx_hw_port_ctrl_req(bp, + PI_PCTRL_M_CONS_BLOCK, + bp->cons_block_phys, + 0, + NULL) != DFX_K_SUCCESS) + { + printk("%s: Could not set consumer block address!\n", bp->dev->name); + return DFX_K_FAILURE; + } + + /* + * Set the base address of Descriptor Block and bring adapter + * to DMA_AVAILABLE state. + * + * Note: We also set the literal and data swapping requirements + * in this command. + * + * Assumption: 32-bit physical address of descriptor block + * is 8Kbyte aligned. + */ + if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_INIT, + (u32)(bp->descr_block_phys | + PI_PDATA_A_INIT_M_BSWAP_INIT), + 0, NULL) != DFX_K_SUCCESS) { + printk("%s: Could not set descriptor block address!\n", + bp->dev->name); + return DFX_K_FAILURE; + } + + /* Set transmit flush timeout value */ + + bp->cmd_req_virt->cmd_type = PI_CMD_K_CHARS_SET; + bp->cmd_req_virt->char_set.item[0].item_code = PI_ITEM_K_FLUSH_TIME; + bp->cmd_req_virt->char_set.item[0].value = 3; /* 3 seconds */ + bp->cmd_req_virt->char_set.item[0].item_index = 0; + bp->cmd_req_virt->char_set.item[1].item_code = PI_ITEM_K_EOL; + if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS) + { + printk("%s: DMA command request failed!\n", bp->dev->name); + return DFX_K_FAILURE; + } + + /* Set the initial values for eFDXEnable and MACTReq MIB objects */ + + bp->cmd_req_virt->cmd_type = PI_CMD_K_SNMP_SET; + bp->cmd_req_virt->snmp_set.item[0].item_code = PI_ITEM_K_FDX_ENB_DIS; + bp->cmd_req_virt->snmp_set.item[0].value = bp->full_duplex_enb; + bp->cmd_req_virt->snmp_set.item[0].item_index = 0; + bp->cmd_req_virt->snmp_set.item[1].item_code = PI_ITEM_K_MAC_T_REQ; + bp->cmd_req_virt->snmp_set.item[1].value = bp->req_ttrt; + bp->cmd_req_virt->snmp_set.item[1].item_index = 0; + bp->cmd_req_virt->snmp_set.item[2].item_code = PI_ITEM_K_EOL; + if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS) + { + printk("%s: DMA command request failed!\n", bp->dev->name); + return DFX_K_FAILURE; + } + + /* Initialize adapter CAM */ + + if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS) + { + printk("%s: Adapter CAM update failed!\n", bp->dev->name); + return DFX_K_FAILURE; + } + + /* Initialize adapter filters */ + + if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS) + { + printk("%s: Adapter filters update failed!\n", bp->dev->name); + return DFX_K_FAILURE; + } + + /* + * Remove any existing dynamic buffers (i.e. if the adapter is being + * reinitialized) + */ + + if (get_buffers) + dfx_rcv_flush(bp); + + /* Initialize receive descriptor block and produce buffers */ + + if (dfx_rcv_init(bp, get_buffers)) + { + printk("%s: Receive buffer allocation failed\n", bp->dev->name); + if (get_buffers) + dfx_rcv_flush(bp); + return DFX_K_FAILURE; + } + + /* Issue START command and bring adapter to LINK_(UN)AVAILABLE state */ + + bp->cmd_req_virt->cmd_type = PI_CMD_K_START; + if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS) + { + printk("%s: Start command failed\n", bp->dev->name); + if (get_buffers) + dfx_rcv_flush(bp); + return DFX_K_FAILURE; + } + + /* Initialization succeeded, reenable PDQ interrupts */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_ENABLE_DEF_INTS); + return DFX_K_SUCCESS; + } + + +/* + * ============ + * = dfx_open = + * ============ + * + * Overview: + * Opens the adapter + * + * Returns: + * Condition code + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * This function brings the adapter to an operational state. + * + * Return Codes: + * 0 - Adapter was successfully opened + * -EAGAIN - Could not register IRQ or adapter initialization failed + * + * Assumptions: + * This routine should only be called for a device that was + * initialized successfully. + * + * Side Effects: + * Adapter should be in LINK_AVAILABLE or LINK_UNAVAILABLE state + * if the open is successful. + */ + +static int dfx_open(struct net_device *dev) +{ + DFX_board_t *bp = netdev_priv(dev); + int ret; + + DBG_printk("In dfx_open...\n"); + + /* Register IRQ - support shared interrupts by passing device ptr */ + + ret = request_irq(dev->irq, dfx_interrupt, IRQF_SHARED, dev->name, + dev); + if (ret) { + printk(KERN_ERR "%s: Requested IRQ %d is busy\n", dev->name, dev->irq); + return ret; + } + + /* + * Set current address to factory MAC address + * + * Note: We've already done this step in dfx_driver_init. + * However, it's possible that a user has set a node + * address override, then closed and reopened the + * adapter. Unless we reset the device address field + * now, we'll continue to use the existing modified + * address. + */ + + memcpy(dev->dev_addr, bp->factory_mac_addr, FDDI_K_ALEN); + + /* Clear local unicast/multicast address tables and counts */ + + memset(bp->uc_table, 0, sizeof(bp->uc_table)); + memset(bp->mc_table, 0, sizeof(bp->mc_table)); + bp->uc_count = 0; + bp->mc_count = 0; + + /* Disable promiscuous filter settings */ + + bp->ind_group_prom = PI_FSTATE_K_BLOCK; + bp->group_prom = PI_FSTATE_K_BLOCK; + + spin_lock_init(&bp->lock); + + /* Reset and initialize adapter */ + + bp->reset_type = PI_PDATA_A_RESET_M_SKIP_ST; /* skip self-test */ + if (dfx_adap_init(bp, 1) != DFX_K_SUCCESS) + { + printk(KERN_ERR "%s: Adapter open failed!\n", dev->name); + free_irq(dev->irq, dev); + return -EAGAIN; + } + + /* Set device structure info */ + netif_start_queue(dev); + return 0; +} + + +/* + * ============= + * = dfx_close = + * ============= + * + * Overview: + * Closes the device/module. + * + * Returns: + * Condition code + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * This routine closes the adapter and brings it to a safe state. + * The interrupt service routine is deregistered with the OS. + * The adapter can be opened again with another call to dfx_open(). + * + * Return Codes: + * Always return 0. + * + * Assumptions: + * No further requests for this adapter are made after this routine is + * called. dfx_open() can be called to reset and reinitialize the + * adapter. + * + * Side Effects: + * Adapter should be in DMA_UNAVAILABLE state upon completion of this + * routine. + */ + +static int dfx_close(struct net_device *dev) +{ + DFX_board_t *bp = netdev_priv(dev); + + DBG_printk("In dfx_close...\n"); + + /* Disable PDQ interrupts first */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS); + + /* Place adapter in DMA_UNAVAILABLE state by resetting adapter */ + + (void) dfx_hw_dma_uninit(bp, PI_PDATA_A_RESET_M_SKIP_ST); + + /* + * Flush any pending transmit buffers + * + * Note: It's important that we flush the transmit buffers + * BEFORE we clear our copy of the Type 2 register. + * Otherwise, we'll have no idea how many buffers + * we need to free. + */ + + dfx_xmt_flush(bp); + + /* + * Clear Type 1 and Type 2 registers after adapter reset + * + * Note: Even though we're closing the adapter, it's + * possible that an interrupt will occur after + * dfx_close is called. Without some assurance to + * the contrary we want to make sure that we don't + * process receive and transmit LLC frames and update + * the Type 2 register with bad information. + */ + + bp->cmd_req_reg.lword = 0; + bp->cmd_rsp_reg.lword = 0; + bp->rcv_xmt_reg.lword = 0; + + /* Clear consumer block for the same reason given above */ + + memset(bp->cons_block_virt, 0, sizeof(PI_CONSUMER_BLOCK)); + + /* Release all dynamically allocate skb in the receive ring. */ + + dfx_rcv_flush(bp); + + /* Clear device structure flags */ + + netif_stop_queue(dev); + + /* Deregister (free) IRQ */ + + free_irq(dev->irq, dev); + + return 0; +} + + +/* + * ====================== + * = dfx_int_pr_halt_id = + * ====================== + * + * Overview: + * Displays halt id's in string form. + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * Determine current halt id and display appropriate string. + * + * Return Codes: + * None + * + * Assumptions: + * None + * + * Side Effects: + * None + */ + +static void dfx_int_pr_halt_id(DFX_board_t *bp) + { + PI_UINT32 port_status; /* PDQ port status register value */ + PI_UINT32 halt_id; /* PDQ port status halt ID */ + + /* Read the latest port status */ + + dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status); + + /* Display halt state transition information */ + + halt_id = (port_status & PI_PSTATUS_M_HALT_ID) >> PI_PSTATUS_V_HALT_ID; + switch (halt_id) + { + case PI_HALT_ID_K_SELFTEST_TIMEOUT: + printk("%s: Halt ID: Selftest Timeout\n", bp->dev->name); + break; + + case PI_HALT_ID_K_PARITY_ERROR: + printk("%s: Halt ID: Host Bus Parity Error\n", bp->dev->name); + break; + + case PI_HALT_ID_K_HOST_DIR_HALT: + printk("%s: Halt ID: Host-Directed Halt\n", bp->dev->name); + break; + + case PI_HALT_ID_K_SW_FAULT: + printk("%s: Halt ID: Adapter Software Fault\n", bp->dev->name); + break; + + case PI_HALT_ID_K_HW_FAULT: + printk("%s: Halt ID: Adapter Hardware Fault\n", bp->dev->name); + break; + + case PI_HALT_ID_K_PC_TRACE: + printk("%s: Halt ID: FDDI Network PC Trace Path Test\n", bp->dev->name); + break; + + case PI_HALT_ID_K_DMA_ERROR: + printk("%s: Halt ID: Adapter DMA Error\n", bp->dev->name); + break; + + case PI_HALT_ID_K_IMAGE_CRC_ERROR: + printk("%s: Halt ID: Firmware Image CRC Error\n", bp->dev->name); + break; + + case PI_HALT_ID_K_BUS_EXCEPTION: + printk("%s: Halt ID: 68000 Bus Exception\n", bp->dev->name); + break; + + default: + printk("%s: Halt ID: Unknown (code = %X)\n", bp->dev->name, halt_id); + break; + } + } + + +/* + * ========================== + * = dfx_int_type_0_process = + * ========================== + * + * Overview: + * Processes Type 0 interrupts. + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * Processes all enabled Type 0 interrupts. If the reason for the interrupt + * is a serious fault on the adapter, then an error message is displayed + * and the adapter is reset. + * + * One tricky potential timing window is the rapid succession of "link avail" + * "link unavail" state change interrupts. The acknowledgement of the Type 0 + * interrupt must be done before reading the state from the Port Status + * register. This is true because a state change could occur after reading + * the data, but before acknowledging the interrupt. If this state change + * does happen, it would be lost because the driver is using the old state, + * and it will never know about the new state because it subsequently + * acknowledges the state change interrupt. + * + * INCORRECT CORRECT + * read type 0 int reasons read type 0 int reasons + * read adapter state ack type 0 interrupts + * ack type 0 interrupts read adapter state + * ... process interrupt ... ... process interrupt ... + * + * Return Codes: + * None + * + * Assumptions: + * None + * + * Side Effects: + * An adapter reset may occur if the adapter has any Type 0 error interrupts + * or if the port status indicates that the adapter is halted. The driver + * is responsible for reinitializing the adapter with the current CAM + * contents and adapter filter settings. + */ + +static void dfx_int_type_0_process(DFX_board_t *bp) + + { + PI_UINT32 type_0_status; /* Host Interrupt Type 0 register */ + PI_UINT32 state; /* current adap state (from port status) */ + + /* + * Read host interrupt Type 0 register to determine which Type 0 + * interrupts are pending. Immediately write it back out to clear + * those interrupts. + */ + + dfx_port_read_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, &type_0_status); + dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, type_0_status); + + /* Check for Type 0 error interrupts */ + + if (type_0_status & (PI_TYPE_0_STAT_M_NXM | + PI_TYPE_0_STAT_M_PM_PAR_ERR | + PI_TYPE_0_STAT_M_BUS_PAR_ERR)) + { + /* Check for Non-Existent Memory error */ + + if (type_0_status & PI_TYPE_0_STAT_M_NXM) + printk("%s: Non-Existent Memory Access Error\n", bp->dev->name); + + /* Check for Packet Memory Parity error */ + + if (type_0_status & PI_TYPE_0_STAT_M_PM_PAR_ERR) + printk("%s: Packet Memory Parity Error\n", bp->dev->name); + + /* Check for Host Bus Parity error */ + + if (type_0_status & PI_TYPE_0_STAT_M_BUS_PAR_ERR) + printk("%s: Host Bus Parity Error\n", bp->dev->name); + + /* Reset adapter and bring it back on-line */ + + bp->link_available = PI_K_FALSE; /* link is no longer available */ + bp->reset_type = 0; /* rerun on-board diagnostics */ + printk("%s: Resetting adapter...\n", bp->dev->name); + if (dfx_adap_init(bp, 0) != DFX_K_SUCCESS) + { + printk("%s: Adapter reset failed! Disabling adapter interrupts.\n", bp->dev->name); + dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS); + return; + } + printk("%s: Adapter reset successful!\n", bp->dev->name); + return; + } + + /* Check for transmit flush interrupt */ + + if (type_0_status & PI_TYPE_0_STAT_M_XMT_FLUSH) + { + /* Flush any pending xmt's and acknowledge the flush interrupt */ + + bp->link_available = PI_K_FALSE; /* link is no longer available */ + dfx_xmt_flush(bp); /* flush any outstanding packets */ + (void) dfx_hw_port_ctrl_req(bp, + PI_PCTRL_M_XMT_DATA_FLUSH_DONE, + 0, + 0, + NULL); + } + + /* Check for adapter state change */ + + if (type_0_status & PI_TYPE_0_STAT_M_STATE_CHANGE) + { + /* Get latest adapter state */ + + state = dfx_hw_adap_state_rd(bp); /* get adapter state */ + if (state == PI_STATE_K_HALTED) + { + /* + * Adapter has transitioned to HALTED state, try to reset + * adapter to bring it back on-line. If reset fails, + * leave the adapter in the broken state. + */ + + printk("%s: Controller has transitioned to HALTED state!\n", bp->dev->name); + dfx_int_pr_halt_id(bp); /* display halt id as string */ + + /* Reset adapter and bring it back on-line */ + + bp->link_available = PI_K_FALSE; /* link is no longer available */ + bp->reset_type = 0; /* rerun on-board diagnostics */ + printk("%s: Resetting adapter...\n", bp->dev->name); + if (dfx_adap_init(bp, 0) != DFX_K_SUCCESS) + { + printk("%s: Adapter reset failed! Disabling adapter interrupts.\n", bp->dev->name); + dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS); + return; + } + printk("%s: Adapter reset successful!\n", bp->dev->name); + } + else if (state == PI_STATE_K_LINK_AVAIL) + { + bp->link_available = PI_K_TRUE; /* set link available flag */ + } + } + } + + +/* + * ================== + * = dfx_int_common = + * ================== + * + * Overview: + * Interrupt service routine (ISR) + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * This is the ISR which processes incoming adapter interrupts. + * + * Return Codes: + * None + * + * Assumptions: + * This routine assumes PDQ interrupts have not been disabled. + * When interrupts are disabled at the PDQ, the Port Status register + * is automatically cleared. This routine uses the Port Status + * register value to determine whether a Type 0 interrupt occurred, + * so it's important that adapter interrupts are not normally + * enabled/disabled at the PDQ. + * + * It's vital that this routine is NOT reentered for the + * same board and that the OS is not in another section of + * code (eg. dfx_xmt_queue_pkt) for the same board on a + * different thread. + * + * Side Effects: + * Pending interrupts are serviced. Depending on the type of + * interrupt, acknowledging and clearing the interrupt at the + * PDQ involves writing a register to clear the interrupt bit + * or updating completion indices. + */ + +static void dfx_int_common(struct net_device *dev) +{ + DFX_board_t *bp = netdev_priv(dev); + PI_UINT32 port_status; /* Port Status register */ + + /* Process xmt interrupts - frequent case, so always call this routine */ + + if(dfx_xmt_done(bp)) /* free consumed xmt packets */ + netif_wake_queue(dev); + + /* Process rcv interrupts - frequent case, so always call this routine */ + + dfx_rcv_queue_process(bp); /* service received LLC frames */ + + /* + * Transmit and receive producer and completion indices are updated on the + * adapter by writing to the Type 2 Producer register. Since the frequent + * case is that we'll be processing either LLC transmit or receive buffers, + * we'll optimize I/O writes by doing a single register write here. + */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword); + + /* Read PDQ Port Status register to find out which interrupts need processing */ + + dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status); + + /* Process Type 0 interrupts (if any) - infrequent, so only call when needed */ + + if (port_status & PI_PSTATUS_M_TYPE_0_PENDING) + dfx_int_type_0_process(bp); /* process Type 0 interrupts */ + } + + +/* + * ================= + * = dfx_interrupt = + * ================= + * + * Overview: + * Interrupt processing routine + * + * Returns: + * Whether a valid interrupt was seen. + * + * Arguments: + * irq - interrupt vector + * dev_id - pointer to device information + * + * Functional Description: + * This routine calls the interrupt processing routine for this adapter. It + * disables and reenables adapter interrupts, as appropriate. We can support + * shared interrupts since the incoming dev_id pointer provides our device + * structure context. + * + * Return Codes: + * IRQ_HANDLED - an IRQ was handled. + * IRQ_NONE - no IRQ was handled. + * + * Assumptions: + * The interrupt acknowledgement at the hardware level (eg. ACKing the PIC + * on Intel-based systems) is done by the operating system outside this + * routine. + * + * System interrupts are enabled through this call. + * + * Side Effects: + * Interrupts are disabled, then reenabled at the adapter. + */ + +static irqreturn_t dfx_interrupt(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + DFX_board_t *bp = netdev_priv(dev); + struct device *bdev = bp->bus_dev; + int dfx_bus_pci = dev_is_pci(bdev); + int dfx_bus_eisa = DFX_BUS_EISA(bdev); + int dfx_bus_tc = DFX_BUS_TC(bdev); + + /* Service adapter interrupts */ + + if (dfx_bus_pci) { + u32 status; + + dfx_port_read_long(bp, PFI_K_REG_STATUS, &status); + if (!(status & PFI_STATUS_M_PDQ_INT)) + return IRQ_NONE; + + spin_lock(&bp->lock); + + /* Disable PDQ-PFI interrupts at PFI */ + dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, + PFI_MODE_M_DMA_ENB); + + /* Call interrupt service routine for this adapter */ + dfx_int_common(dev); + + /* Clear PDQ interrupt status bit and reenable interrupts */ + dfx_port_write_long(bp, PFI_K_REG_STATUS, + PFI_STATUS_M_PDQ_INT); + dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, + (PFI_MODE_M_PDQ_INT_ENB | + PFI_MODE_M_DMA_ENB)); + + spin_unlock(&bp->lock); + } + if (dfx_bus_eisa) { + unsigned long base_addr = to_eisa_device(bdev)->base_addr; + u8 status; + + status = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + if (!(status & PI_CONFIG_STAT_0_M_PEND)) + return IRQ_NONE; + + spin_lock(&bp->lock); + + /* Disable interrupts at the ESIC */ + status &= ~PI_CONFIG_STAT_0_M_INT_ENB; + outb(status, base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + + /* Call interrupt service routine for this adapter */ + dfx_int_common(dev); + + /* Reenable interrupts at the ESIC */ + status = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + status |= PI_CONFIG_STAT_0_M_INT_ENB; + outb(status, base_addr + PI_ESIC_K_IO_CONFIG_STAT_0); + + spin_unlock(&bp->lock); + } + if (dfx_bus_tc) { + u32 status; + + dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &status); + if (!(status & (PI_PSTATUS_M_RCV_DATA_PENDING | + PI_PSTATUS_M_XMT_DATA_PENDING | + PI_PSTATUS_M_SMT_HOST_PENDING | + PI_PSTATUS_M_UNSOL_PENDING | + PI_PSTATUS_M_CMD_RSP_PENDING | + PI_PSTATUS_M_CMD_REQ_PENDING | + PI_PSTATUS_M_TYPE_0_PENDING))) + return IRQ_NONE; + + spin_lock(&bp->lock); + + /* Call interrupt service routine for this adapter */ + dfx_int_common(dev); + + spin_unlock(&bp->lock); + } + + return IRQ_HANDLED; +} + + +/* + * ===================== + * = dfx_ctl_get_stats = + * ===================== + * + * Overview: + * Get statistics for FDDI adapter + * + * Returns: + * Pointer to FDDI statistics structure + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * Gets current MIB objects from adapter, then + * returns FDDI statistics structure as defined + * in if_fddi.h. + * + * Note: Since the FDDI statistics structure is + * still new and the device structure doesn't + * have an FDDI-specific get statistics handler, + * we'll return the FDDI statistics structure as + * a pointer to an Ethernet statistics structure. + * That way, at least the first part of the statistics + * structure can be decoded properly, and it allows + * "smart" applications to perform a second cast to + * decode the FDDI-specific statistics. + * + * We'll have to pay attention to this routine as the + * device structure becomes more mature and LAN media + * independent. + * + * Return Codes: + * None + * + * Assumptions: + * None + * + * Side Effects: + * None + */ + +static struct net_device_stats *dfx_ctl_get_stats(struct net_device *dev) + { + DFX_board_t *bp = netdev_priv(dev); + + /* Fill the bp->stats structure with driver-maintained counters */ + + bp->stats.gen.rx_packets = bp->rcv_total_frames; + bp->stats.gen.tx_packets = bp->xmt_total_frames; + bp->stats.gen.rx_bytes = bp->rcv_total_bytes; + bp->stats.gen.tx_bytes = bp->xmt_total_bytes; + bp->stats.gen.rx_errors = bp->rcv_crc_errors + + bp->rcv_frame_status_errors + + bp->rcv_length_errors; + bp->stats.gen.tx_errors = bp->xmt_length_errors; + bp->stats.gen.rx_dropped = bp->rcv_discards; + bp->stats.gen.tx_dropped = bp->xmt_discards; + bp->stats.gen.multicast = bp->rcv_multicast_frames; + bp->stats.gen.collisions = 0; /* always zero (0) for FDDI */ + + /* Get FDDI SMT MIB objects */ + + bp->cmd_req_virt->cmd_type = PI_CMD_K_SMT_MIB_GET; + if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS) + return (struct net_device_stats *)&bp->stats; + + /* Fill the bp->stats structure with the SMT MIB object values */ + + memcpy(bp->stats.smt_station_id, &bp->cmd_rsp_virt->smt_mib_get.smt_station_id, sizeof(bp->cmd_rsp_virt->smt_mib_get.smt_station_id)); + bp->stats.smt_op_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_op_version_id; + bp->stats.smt_hi_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_hi_version_id; + bp->stats.smt_lo_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_lo_version_id; + memcpy(bp->stats.smt_user_data, &bp->cmd_rsp_virt->smt_mib_get.smt_user_data, sizeof(bp->cmd_rsp_virt->smt_mib_get.smt_user_data)); + bp->stats.smt_mib_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_mib_version_id; + bp->stats.smt_mac_cts = bp->cmd_rsp_virt->smt_mib_get.smt_mac_ct; + bp->stats.smt_non_master_cts = bp->cmd_rsp_virt->smt_mib_get.smt_non_master_ct; + bp->stats.smt_master_cts = bp->cmd_rsp_virt->smt_mib_get.smt_master_ct; + bp->stats.smt_available_paths = bp->cmd_rsp_virt->smt_mib_get.smt_available_paths; + bp->stats.smt_config_capabilities = bp->cmd_rsp_virt->smt_mib_get.smt_config_capabilities; + bp->stats.smt_config_policy = bp->cmd_rsp_virt->smt_mib_get.smt_config_policy; + bp->stats.smt_connection_policy = bp->cmd_rsp_virt->smt_mib_get.smt_connection_policy; + bp->stats.smt_t_notify = bp->cmd_rsp_virt->smt_mib_get.smt_t_notify; + bp->stats.smt_stat_rpt_policy = bp->cmd_rsp_virt->smt_mib_get.smt_stat_rpt_policy; + bp->stats.smt_trace_max_expiration = bp->cmd_rsp_virt->smt_mib_get.smt_trace_max_expiration; + bp->stats.smt_bypass_present = bp->cmd_rsp_virt->smt_mib_get.smt_bypass_present; + bp->stats.smt_ecm_state = bp->cmd_rsp_virt->smt_mib_get.smt_ecm_state; + bp->stats.smt_cf_state = bp->cmd_rsp_virt->smt_mib_get.smt_cf_state; + bp->stats.smt_remote_disconnect_flag = bp->cmd_rsp_virt->smt_mib_get.smt_remote_disconnect_flag; + bp->stats.smt_station_status = bp->cmd_rsp_virt->smt_mib_get.smt_station_status; + bp->stats.smt_peer_wrap_flag = bp->cmd_rsp_virt->smt_mib_get.smt_peer_wrap_flag; + bp->stats.smt_time_stamp = bp->cmd_rsp_virt->smt_mib_get.smt_msg_time_stamp.ls; + bp->stats.smt_transition_time_stamp = bp->cmd_rsp_virt->smt_mib_get.smt_transition_time_stamp.ls; + bp->stats.mac_frame_status_functions = bp->cmd_rsp_virt->smt_mib_get.mac_frame_status_functions; + bp->stats.mac_t_max_capability = bp->cmd_rsp_virt->smt_mib_get.mac_t_max_capability; + bp->stats.mac_tvx_capability = bp->cmd_rsp_virt->smt_mib_get.mac_tvx_capability; + bp->stats.mac_available_paths = bp->cmd_rsp_virt->smt_mib_get.mac_available_paths; + bp->stats.mac_current_path = bp->cmd_rsp_virt->smt_mib_get.mac_current_path; + memcpy(bp->stats.mac_upstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_upstream_nbr, FDDI_K_ALEN); + memcpy(bp->stats.mac_downstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_downstream_nbr, FDDI_K_ALEN); + memcpy(bp->stats.mac_old_upstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_old_upstream_nbr, FDDI_K_ALEN); + memcpy(bp->stats.mac_old_downstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_old_downstream_nbr, FDDI_K_ALEN); + bp->stats.mac_dup_address_test = bp->cmd_rsp_virt->smt_mib_get.mac_dup_address_test; + bp->stats.mac_requested_paths = bp->cmd_rsp_virt->smt_mib_get.mac_requested_paths; + bp->stats.mac_downstream_port_type = bp->cmd_rsp_virt->smt_mib_get.mac_downstream_port_type; + memcpy(bp->stats.mac_smt_address, &bp->cmd_rsp_virt->smt_mib_get.mac_smt_address, FDDI_K_ALEN); + bp->stats.mac_t_req = bp->cmd_rsp_virt->smt_mib_get.mac_t_req; + bp->stats.mac_t_neg = bp->cmd_rsp_virt->smt_mib_get.mac_t_neg; + bp->stats.mac_t_max = bp->cmd_rsp_virt->smt_mib_get.mac_t_max; + bp->stats.mac_tvx_value = bp->cmd_rsp_virt->smt_mib_get.mac_tvx_value; + bp->stats.mac_frame_error_threshold = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_threshold; + bp->stats.mac_frame_error_ratio = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_ratio; + bp->stats.mac_rmt_state = bp->cmd_rsp_virt->smt_mib_get.mac_rmt_state; + bp->stats.mac_da_flag = bp->cmd_rsp_virt->smt_mib_get.mac_da_flag; + bp->stats.mac_una_da_flag = bp->cmd_rsp_virt->smt_mib_get.mac_unda_flag; + bp->stats.mac_frame_error_flag = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_flag; + bp->stats.mac_ma_unitdata_available = bp->cmd_rsp_virt->smt_mib_get.mac_ma_unitdata_available; + bp->stats.mac_hardware_present = bp->cmd_rsp_virt->smt_mib_get.mac_hardware_present; + bp->stats.mac_ma_unitdata_enable = bp->cmd_rsp_virt->smt_mib_get.mac_ma_unitdata_enable; + bp->stats.path_tvx_lower_bound = bp->cmd_rsp_virt->smt_mib_get.path_tvx_lower_bound; + bp->stats.path_t_max_lower_bound = bp->cmd_rsp_virt->smt_mib_get.path_t_max_lower_bound; + bp->stats.path_max_t_req = bp->cmd_rsp_virt->smt_mib_get.path_max_t_req; + memcpy(bp->stats.path_configuration, &bp->cmd_rsp_virt->smt_mib_get.path_configuration, sizeof(bp->cmd_rsp_virt->smt_mib_get.path_configuration)); + bp->stats.port_my_type[0] = bp->cmd_rsp_virt->smt_mib_get.port_my_type[0]; + bp->stats.port_my_type[1] = bp->cmd_rsp_virt->smt_mib_get.port_my_type[1]; + bp->stats.port_neighbor_type[0] = bp->cmd_rsp_virt->smt_mib_get.port_neighbor_type[0]; + bp->stats.port_neighbor_type[1] = bp->cmd_rsp_virt->smt_mib_get.port_neighbor_type[1]; + bp->stats.port_connection_policies[0] = bp->cmd_rsp_virt->smt_mib_get.port_connection_policies[0]; + bp->stats.port_connection_policies[1] = bp->cmd_rsp_virt->smt_mib_get.port_connection_policies[1]; + bp->stats.port_mac_indicated[0] = bp->cmd_rsp_virt->smt_mib_get.port_mac_indicated[0]; + bp->stats.port_mac_indicated[1] = bp->cmd_rsp_virt->smt_mib_get.port_mac_indicated[1]; + bp->stats.port_current_path[0] = bp->cmd_rsp_virt->smt_mib_get.port_current_path[0]; + bp->stats.port_current_path[1] = bp->cmd_rsp_virt->smt_mib_get.port_current_path[1]; + memcpy(&bp->stats.port_requested_paths[0*3], &bp->cmd_rsp_virt->smt_mib_get.port_requested_paths[0], 3); + memcpy(&bp->stats.port_requested_paths[1*3], &bp->cmd_rsp_virt->smt_mib_get.port_requested_paths[1], 3); + bp->stats.port_mac_placement[0] = bp->cmd_rsp_virt->smt_mib_get.port_mac_placement[0]; + bp->stats.port_mac_placement[1] = bp->cmd_rsp_virt->smt_mib_get.port_mac_placement[1]; + bp->stats.port_available_paths[0] = bp->cmd_rsp_virt->smt_mib_get.port_available_paths[0]; + bp->stats.port_available_paths[1] = bp->cmd_rsp_virt->smt_mib_get.port_available_paths[1]; + bp->stats.port_pmd_class[0] = bp->cmd_rsp_virt->smt_mib_get.port_pmd_class[0]; + bp->stats.port_pmd_class[1] = bp->cmd_rsp_virt->smt_mib_get.port_pmd_class[1]; + bp->stats.port_connection_capabilities[0] = bp->cmd_rsp_virt->smt_mib_get.port_connection_capabilities[0]; + bp->stats.port_connection_capabilities[1] = bp->cmd_rsp_virt->smt_mib_get.port_connection_capabilities[1]; + bp->stats.port_bs_flag[0] = bp->cmd_rsp_virt->smt_mib_get.port_bs_flag[0]; + bp->stats.port_bs_flag[1] = bp->cmd_rsp_virt->smt_mib_get.port_bs_flag[1]; + bp->stats.port_ler_estimate[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_estimate[0]; + bp->stats.port_ler_estimate[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_estimate[1]; + bp->stats.port_ler_cutoff[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_cutoff[0]; + bp->stats.port_ler_cutoff[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_cutoff[1]; + bp->stats.port_ler_alarm[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_alarm[0]; + bp->stats.port_ler_alarm[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_alarm[1]; + bp->stats.port_connect_state[0] = bp->cmd_rsp_virt->smt_mib_get.port_connect_state[0]; + bp->stats.port_connect_state[1] = bp->cmd_rsp_virt->smt_mib_get.port_connect_state[1]; + bp->stats.port_pcm_state[0] = bp->cmd_rsp_virt->smt_mib_get.port_pcm_state[0]; + bp->stats.port_pcm_state[1] = bp->cmd_rsp_virt->smt_mib_get.port_pcm_state[1]; + bp->stats.port_pc_withhold[0] = bp->cmd_rsp_virt->smt_mib_get.port_pc_withhold[0]; + bp->stats.port_pc_withhold[1] = bp->cmd_rsp_virt->smt_mib_get.port_pc_withhold[1]; + bp->stats.port_ler_flag[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_flag[0]; + bp->stats.port_ler_flag[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_flag[1]; + bp->stats.port_hardware_present[0] = bp->cmd_rsp_virt->smt_mib_get.port_hardware_present[0]; + bp->stats.port_hardware_present[1] = bp->cmd_rsp_virt->smt_mib_get.port_hardware_present[1]; + + /* Get FDDI counters */ + + bp->cmd_req_virt->cmd_type = PI_CMD_K_CNTRS_GET; + if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS) + return (struct net_device_stats *)&bp->stats; + + /* Fill the bp->stats structure with the FDDI counter values */ + + bp->stats.mac_frame_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.frame_cnt.ls; + bp->stats.mac_copied_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.copied_cnt.ls; + bp->stats.mac_transmit_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.transmit_cnt.ls; + bp->stats.mac_error_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.error_cnt.ls; + bp->stats.mac_lost_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.lost_cnt.ls; + bp->stats.port_lct_fail_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.lct_rejects[0].ls; + bp->stats.port_lct_fail_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.lct_rejects[1].ls; + bp->stats.port_lem_reject_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.lem_rejects[0].ls; + bp->stats.port_lem_reject_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.lem_rejects[1].ls; + bp->stats.port_lem_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.link_errors[0].ls; + bp->stats.port_lem_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.link_errors[1].ls; + + return (struct net_device_stats *)&bp->stats; + } + + +/* + * ============================== + * = dfx_ctl_set_multicast_list = + * ============================== + * + * Overview: + * Enable/Disable LLC frame promiscuous mode reception + * on the adapter and/or update multicast address table. + * + * Returns: + * None + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * This routine follows a fairly simple algorithm for setting the + * adapter filters and CAM: + * + * if IFF_PROMISC flag is set + * enable LLC individual/group promiscuous mode + * else + * disable LLC individual/group promiscuous mode + * if number of incoming multicast addresses > + * (CAM max size - number of unicast addresses in CAM) + * enable LLC group promiscuous mode + * set driver-maintained multicast address count to zero + * else + * disable LLC group promiscuous mode + * set driver-maintained multicast address count to incoming count + * update adapter CAM + * update adapter filters + * + * Return Codes: + * None + * + * Assumptions: + * Multicast addresses are presented in canonical (LSB) format. + * + * Side Effects: + * On-board adapter CAM and filters are updated. + */ + +static void dfx_ctl_set_multicast_list(struct net_device *dev) +{ + DFX_board_t *bp = netdev_priv(dev); + int i; /* used as index in for loop */ + struct netdev_hw_addr *ha; + + /* Enable LLC frame promiscuous mode, if necessary */ + + if (dev->flags & IFF_PROMISC) + bp->ind_group_prom = PI_FSTATE_K_PASS; /* Enable LLC ind/group prom mode */ + + /* Else, update multicast address table */ + + else + { + bp->ind_group_prom = PI_FSTATE_K_BLOCK; /* Disable LLC ind/group prom mode */ + /* + * Check whether incoming multicast address count exceeds table size + * + * Note: The adapters utilize an on-board 64 entry CAM for + * supporting perfect filtering of multicast packets + * and bridge functions when adding unicast addresses. + * There is no hash function available. To support + * additional multicast addresses, the all multicast + * filter (LLC group promiscuous mode) must be enabled. + * + * The firmware reserves two CAM entries for SMT-related + * multicast addresses, which leaves 62 entries available. + * The following code ensures that we're not being asked + * to add more than 62 addresses to the CAM. If we are, + * the driver will enable the all multicast filter. + * Should the number of multicast addresses drop below + * the high water mark, the filter will be disabled and + * perfect filtering will be used. + */ + + if (netdev_mc_count(dev) > (PI_CMD_ADDR_FILTER_K_SIZE - bp->uc_count)) + { + bp->group_prom = PI_FSTATE_K_PASS; /* Enable LLC group prom mode */ + bp->mc_count = 0; /* Don't add mc addrs to CAM */ + } + else + { + bp->group_prom = PI_FSTATE_K_BLOCK; /* Disable LLC group prom mode */ + bp->mc_count = netdev_mc_count(dev); /* Add mc addrs to CAM */ + } + + /* Copy addresses to multicast address table, then update adapter CAM */ + + i = 0; + netdev_for_each_mc_addr(ha, dev) + memcpy(&bp->mc_table[i++ * FDDI_K_ALEN], + ha->addr, FDDI_K_ALEN); + + if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS) + { + DBG_printk("%s: Could not update multicast address table!\n", dev->name); + } + else + { + DBG_printk("%s: Multicast address table updated! Added %d addresses.\n", dev->name, bp->mc_count); + } + } + + /* Update adapter filters */ + + if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS) + { + DBG_printk("%s: Could not update adapter filters!\n", dev->name); + } + else + { + DBG_printk("%s: Adapter filters updated!\n", dev->name); + } + } + + +/* + * =========================== + * = dfx_ctl_set_mac_address = + * =========================== + * + * Overview: + * Add node address override (unicast address) to adapter + * CAM and update dev_addr field in device table. + * + * Returns: + * None + * + * Arguments: + * dev - pointer to device information + * addr - pointer to sockaddr structure containing unicast address to add + * + * Functional Description: + * The adapter supports node address overrides by adding one or more + * unicast addresses to the adapter CAM. This is similar to adding + * multicast addresses. In this routine we'll update the driver and + * device structures with the new address, then update the adapter CAM + * to ensure that the adapter will copy and strip frames destined and + * sourced by that address. + * + * Return Codes: + * Always returns zero. + * + * Assumptions: + * The address pointed to by addr->sa_data is a valid unicast + * address and is presented in canonical (LSB) format. + * + * Side Effects: + * On-board adapter CAM is updated. On-board adapter filters + * may be updated. + */ + +static int dfx_ctl_set_mac_address(struct net_device *dev, void *addr) + { + struct sockaddr *p_sockaddr = (struct sockaddr *)addr; + DFX_board_t *bp = netdev_priv(dev); + + /* Copy unicast address to driver-maintained structs and update count */ + + memcpy(dev->dev_addr, p_sockaddr->sa_data, FDDI_K_ALEN); /* update device struct */ + memcpy(&bp->uc_table[0], p_sockaddr->sa_data, FDDI_K_ALEN); /* update driver struct */ + bp->uc_count = 1; + + /* + * Verify we're not exceeding the CAM size by adding unicast address + * + * Note: It's possible that before entering this routine we've + * already filled the CAM with 62 multicast addresses. + * Since we need to place the node address override into + * the CAM, we have to check to see that we're not + * exceeding the CAM size. If we are, we have to enable + * the LLC group (multicast) promiscuous mode filter as + * in dfx_ctl_set_multicast_list. + */ + + if ((bp->uc_count + bp->mc_count) > PI_CMD_ADDR_FILTER_K_SIZE) + { + bp->group_prom = PI_FSTATE_K_PASS; /* Enable LLC group prom mode */ + bp->mc_count = 0; /* Don't add mc addrs to CAM */ + + /* Update adapter filters */ + + if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS) + { + DBG_printk("%s: Could not update adapter filters!\n", dev->name); + } + else + { + DBG_printk("%s: Adapter filters updated!\n", dev->name); + } + } + + /* Update adapter CAM with new unicast address */ + + if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS) + { + DBG_printk("%s: Could not set new MAC address!\n", dev->name); + } + else + { + DBG_printk("%s: Adapter CAM updated with new MAC address\n", dev->name); + } + return 0; /* always return zero */ + } + + +/* + * ====================== + * = dfx_ctl_update_cam = + * ====================== + * + * Overview: + * Procedure to update adapter CAM (Content Addressable Memory) + * with desired unicast and multicast address entries. + * + * Returns: + * Condition code + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * Updates adapter CAM with current contents of board structure + * unicast and multicast address tables. Since there are only 62 + * free entries in CAM, this routine ensures that the command + * request buffer is not overrun. + * + * Return Codes: + * DFX_K_SUCCESS - Request succeeded + * DFX_K_FAILURE - Request failed + * + * Assumptions: + * All addresses being added (unicast and multicast) are in canonical + * order. + * + * Side Effects: + * On-board adapter CAM is updated. + */ + +static int dfx_ctl_update_cam(DFX_board_t *bp) + { + int i; /* used as index */ + PI_LAN_ADDR *p_addr; /* pointer to CAM entry */ + + /* + * Fill in command request information + * + * Note: Even though both the unicast and multicast address + * table entries are stored as contiguous 6 byte entries, + * the firmware address filter set command expects each + * entry to be two longwords (8 bytes total). We must be + * careful to only copy the six bytes of each unicast and + * multicast table entry into each command entry. This + * is also why we must first clear the entire command + * request buffer. + */ + + memset(bp->cmd_req_virt, 0, PI_CMD_REQ_K_SIZE_MAX); /* first clear buffer */ + bp->cmd_req_virt->cmd_type = PI_CMD_K_ADDR_FILTER_SET; + p_addr = &bp->cmd_req_virt->addr_filter_set.entry[0]; + + /* Now add unicast addresses to command request buffer, if any */ + + for (i=0; i < (int)bp->uc_count; i++) + { + if (i < PI_CMD_ADDR_FILTER_K_SIZE) + { + memcpy(p_addr, &bp->uc_table[i*FDDI_K_ALEN], FDDI_K_ALEN); + p_addr++; /* point to next command entry */ + } + } + + /* Now add multicast addresses to command request buffer, if any */ + + for (i=0; i < (int)bp->mc_count; i++) + { + if ((i + bp->uc_count) < PI_CMD_ADDR_FILTER_K_SIZE) + { + memcpy(p_addr, &bp->mc_table[i*FDDI_K_ALEN], FDDI_K_ALEN); + p_addr++; /* point to next command entry */ + } + } + + /* Issue command to update adapter CAM, then return */ + + if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS) + return DFX_K_FAILURE; + return DFX_K_SUCCESS; + } + + +/* + * ========================== + * = dfx_ctl_update_filters = + * ========================== + * + * Overview: + * Procedure to update adapter filters with desired + * filter settings. + * + * Returns: + * Condition code + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * Enables or disables filter using current filter settings. + * + * Return Codes: + * DFX_K_SUCCESS - Request succeeded. + * DFX_K_FAILURE - Request failed. + * + * Assumptions: + * We must always pass up packets destined to the broadcast + * address (FF-FF-FF-FF-FF-FF), so we'll always keep the + * broadcast filter enabled. + * + * Side Effects: + * On-board adapter filters are updated. + */ + +static int dfx_ctl_update_filters(DFX_board_t *bp) + { + int i = 0; /* used as index */ + + /* Fill in command request information */ + + bp->cmd_req_virt->cmd_type = PI_CMD_K_FILTERS_SET; + + /* Initialize Broadcast filter - * ALWAYS ENABLED * */ + + bp->cmd_req_virt->filter_set.item[i].item_code = PI_ITEM_K_BROADCAST; + bp->cmd_req_virt->filter_set.item[i++].value = PI_FSTATE_K_PASS; + + /* Initialize LLC Individual/Group Promiscuous filter */ + + bp->cmd_req_virt->filter_set.item[i].item_code = PI_ITEM_K_IND_GROUP_PROM; + bp->cmd_req_virt->filter_set.item[i++].value = bp->ind_group_prom; + + /* Initialize LLC Group Promiscuous filter */ + + bp->cmd_req_virt->filter_set.item[i].item_code = PI_ITEM_K_GROUP_PROM; + bp->cmd_req_virt->filter_set.item[i++].value = bp->group_prom; + + /* Terminate the item code list */ + + bp->cmd_req_virt->filter_set.item[i].item_code = PI_ITEM_K_EOL; + + /* Issue command to update adapter filters, then return */ + + if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS) + return DFX_K_FAILURE; + return DFX_K_SUCCESS; + } + + +/* + * ====================== + * = dfx_hw_dma_cmd_req = + * ====================== + * + * Overview: + * Sends PDQ DMA command to adapter firmware + * + * Returns: + * Condition code + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * The command request and response buffers are posted to the adapter in the manner + * described in the PDQ Port Specification: + * + * 1. Command Response Buffer is posted to adapter. + * 2. Command Request Buffer is posted to adapter. + * 3. Command Request consumer index is polled until it indicates that request + * buffer has been DMA'd to adapter. + * 4. Command Response consumer index is polled until it indicates that response + * buffer has been DMA'd from adapter. + * + * This ordering ensures that a response buffer is already available for the firmware + * to use once it's done processing the request buffer. + * + * Return Codes: + * DFX_K_SUCCESS - DMA command succeeded + * DFX_K_OUTSTATE - Adapter is NOT in proper state + * DFX_K_HW_TIMEOUT - DMA command timed out + * + * Assumptions: + * Command request buffer has already been filled with desired DMA command. + * + * Side Effects: + * None + */ + +static int dfx_hw_dma_cmd_req(DFX_board_t *bp) + { + int status; /* adapter status */ + int timeout_cnt; /* used in for loops */ + + /* Make sure the adapter is in a state that we can issue the DMA command in */ + + status = dfx_hw_adap_state_rd(bp); + if ((status == PI_STATE_K_RESET) || + (status == PI_STATE_K_HALTED) || + (status == PI_STATE_K_DMA_UNAVAIL) || + (status == PI_STATE_K_UPGRADE)) + return DFX_K_OUTSTATE; + + /* Put response buffer on the command response queue */ + + bp->descr_block_virt->cmd_rsp[bp->cmd_rsp_reg.index.prod].long_0 = (u32) (PI_RCV_DESCR_M_SOP | + ((PI_CMD_RSP_K_SIZE_MAX / PI_ALIGN_K_CMD_RSP_BUFF) << PI_RCV_DESCR_V_SEG_LEN)); + bp->descr_block_virt->cmd_rsp[bp->cmd_rsp_reg.index.prod].long_1 = bp->cmd_rsp_phys; + + /* Bump (and wrap) the producer index and write out to register */ + + bp->cmd_rsp_reg.index.prod += 1; + bp->cmd_rsp_reg.index.prod &= PI_CMD_RSP_K_NUM_ENTRIES-1; + dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_RSP_PROD, bp->cmd_rsp_reg.lword); + + /* Put request buffer on the command request queue */ + + bp->descr_block_virt->cmd_req[bp->cmd_req_reg.index.prod].long_0 = (u32) (PI_XMT_DESCR_M_SOP | + PI_XMT_DESCR_M_EOP | (PI_CMD_REQ_K_SIZE_MAX << PI_XMT_DESCR_V_SEG_LEN)); + bp->descr_block_virt->cmd_req[bp->cmd_req_reg.index.prod].long_1 = bp->cmd_req_phys; + + /* Bump (and wrap) the producer index and write out to register */ + + bp->cmd_req_reg.index.prod += 1; + bp->cmd_req_reg.index.prod &= PI_CMD_REQ_K_NUM_ENTRIES-1; + dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_REQ_PROD, bp->cmd_req_reg.lword); + + /* + * Here we wait for the command request consumer index to be equal + * to the producer, indicating that the adapter has DMAed the request. + */ + + for (timeout_cnt = 20000; timeout_cnt > 0; timeout_cnt--) + { + if (bp->cmd_req_reg.index.prod == (u8)(bp->cons_block_virt->cmd_req)) + break; + udelay(100); /* wait for 100 microseconds */ + } + if (timeout_cnt == 0) + return DFX_K_HW_TIMEOUT; + + /* Bump (and wrap) the completion index and write out to register */ + + bp->cmd_req_reg.index.comp += 1; + bp->cmd_req_reg.index.comp &= PI_CMD_REQ_K_NUM_ENTRIES-1; + dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_REQ_PROD, bp->cmd_req_reg.lword); + + /* + * Here we wait for the command response consumer index to be equal + * to the producer, indicating that the adapter has DMAed the response. + */ + + for (timeout_cnt = 20000; timeout_cnt > 0; timeout_cnt--) + { + if (bp->cmd_rsp_reg.index.prod == (u8)(bp->cons_block_virt->cmd_rsp)) + break; + udelay(100); /* wait for 100 microseconds */ + } + if (timeout_cnt == 0) + return DFX_K_HW_TIMEOUT; + + /* Bump (and wrap) the completion index and write out to register */ + + bp->cmd_rsp_reg.index.comp += 1; + bp->cmd_rsp_reg.index.comp &= PI_CMD_RSP_K_NUM_ENTRIES-1; + dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_RSP_PROD, bp->cmd_rsp_reg.lword); + return DFX_K_SUCCESS; + } + + +/* + * ======================== + * = dfx_hw_port_ctrl_req = + * ======================== + * + * Overview: + * Sends PDQ port control command to adapter firmware + * + * Returns: + * Host data register value in host_data if ptr is not NULL + * + * Arguments: + * bp - pointer to board information + * command - port control command + * data_a - port data A register value + * data_b - port data B register value + * host_data - ptr to host data register value + * + * Functional Description: + * Send generic port control command to adapter by writing + * to various PDQ port registers, then polling for completion. + * + * Return Codes: + * DFX_K_SUCCESS - port control command succeeded + * DFX_K_HW_TIMEOUT - port control command timed out + * + * Assumptions: + * None + * + * Side Effects: + * None + */ + +static int dfx_hw_port_ctrl_req( + DFX_board_t *bp, + PI_UINT32 command, + PI_UINT32 data_a, + PI_UINT32 data_b, + PI_UINT32 *host_data + ) + + { + PI_UINT32 port_cmd; /* Port Control command register value */ + int timeout_cnt; /* used in for loops */ + + /* Set Command Error bit in command longword */ + + port_cmd = (PI_UINT32) (command | PI_PCTRL_M_CMD_ERROR); + + /* Issue port command to the adapter */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_A, data_a); + dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_B, data_b); + dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_CTRL, port_cmd); + + /* Now wait for command to complete */ + + if (command == PI_PCTRL_M_BLAST_FLASH) + timeout_cnt = 600000; /* set command timeout count to 60 seconds */ + else + timeout_cnt = 20000; /* set command timeout count to 2 seconds */ + + for (; timeout_cnt > 0; timeout_cnt--) + { + dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_CTRL, &port_cmd); + if (!(port_cmd & PI_PCTRL_M_CMD_ERROR)) + break; + udelay(100); /* wait for 100 microseconds */ + } + if (timeout_cnt == 0) + return DFX_K_HW_TIMEOUT; + + /* + * If the address of host_data is non-zero, assume caller has supplied a + * non NULL pointer, and return the contents of the HOST_DATA register in + * it. + */ + + if (host_data != NULL) + dfx_port_read_long(bp, PI_PDQ_K_REG_HOST_DATA, host_data); + return DFX_K_SUCCESS; + } + + +/* + * ===================== + * = dfx_hw_adap_reset = + * ===================== + * + * Overview: + * Resets adapter + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * type - type of reset to perform + * + * Functional Description: + * Issue soft reset to adapter by writing to PDQ Port Reset + * register. Use incoming reset type to tell adapter what + * kind of reset operation to perform. + * + * Return Codes: + * None + * + * Assumptions: + * This routine merely issues a soft reset to the adapter. + * It is expected that after this routine returns, the caller + * will appropriately poll the Port Status register for the + * adapter to enter the proper state. + * + * Side Effects: + * Internal adapter registers are cleared. + */ + +static void dfx_hw_adap_reset( + DFX_board_t *bp, + PI_UINT32 type + ) + + { + /* Set Reset type and assert reset */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_A, type); /* tell adapter type of reset */ + dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_RESET, PI_RESET_M_ASSERT_RESET); + + /* Wait for at least 1 Microsecond according to the spec. We wait 20 just to be safe */ + + udelay(20); + + /* Deassert reset */ + + dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_RESET, 0); + } + + +/* + * ======================== + * = dfx_hw_adap_state_rd = + * ======================== + * + * Overview: + * Returns current adapter state + * + * Returns: + * Adapter state per PDQ Port Specification + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * Reads PDQ Port Status register and returns adapter state. + * + * Return Codes: + * None + * + * Assumptions: + * None + * + * Side Effects: + * None + */ + +static int dfx_hw_adap_state_rd(DFX_board_t *bp) + { + PI_UINT32 port_status; /* Port Status register value */ + + dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status); + return (port_status & PI_PSTATUS_M_STATE) >> PI_PSTATUS_V_STATE; + } + + +/* + * ===================== + * = dfx_hw_dma_uninit = + * ===================== + * + * Overview: + * Brings adapter to DMA_UNAVAILABLE state + * + * Returns: + * Condition code + * + * Arguments: + * bp - pointer to board information + * type - type of reset to perform + * + * Functional Description: + * Bring adapter to DMA_UNAVAILABLE state by performing the following: + * 1. Set reset type bit in Port Data A Register then reset adapter. + * 2. Check that adapter is in DMA_UNAVAILABLE state. + * + * Return Codes: + * DFX_K_SUCCESS - adapter is in DMA_UNAVAILABLE state + * DFX_K_HW_TIMEOUT - adapter did not reset properly + * + * Assumptions: + * None + * + * Side Effects: + * Internal adapter registers are cleared. + */ + +static int dfx_hw_dma_uninit(DFX_board_t *bp, PI_UINT32 type) + { + int timeout_cnt; /* used in for loops */ + + /* Set reset type bit and reset adapter */ + + dfx_hw_adap_reset(bp, type); + + /* Now wait for adapter to enter DMA_UNAVAILABLE state */ + + for (timeout_cnt = 100000; timeout_cnt > 0; timeout_cnt--) + { + if (dfx_hw_adap_state_rd(bp) == PI_STATE_K_DMA_UNAVAIL) + break; + udelay(100); /* wait for 100 microseconds */ + } + if (timeout_cnt == 0) + return DFX_K_HW_TIMEOUT; + return DFX_K_SUCCESS; + } + +/* + * Align an sk_buff to a boundary power of 2 + * + */ +#ifdef DYNAMIC_BUFFERS +static void my_skb_align(struct sk_buff *skb, int n) +{ + unsigned long x = (unsigned long)skb->data; + unsigned long v; + + v = ALIGN(x, n); /* Where we want to be */ + + skb_reserve(skb, v - x); +} +#endif + +/* + * ================ + * = dfx_rcv_init = + * ================ + * + * Overview: + * Produces buffers to adapter LLC Host receive descriptor block + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * get_buffers - non-zero if buffers to be allocated + * + * Functional Description: + * This routine can be called during dfx_adap_init() or during an adapter + * reset. It initializes the descriptor block and produces all allocated + * LLC Host queue receive buffers. + * + * Return Codes: + * Return 0 on success or -ENOMEM if buffer allocation failed (when using + * dynamic buffer allocation). If the buffer allocation failed, the + * already allocated buffers will not be released and the caller should do + * this. + * + * Assumptions: + * The PDQ has been reset and the adapter and driver maintained Type 2 + * register indices are cleared. + * + * Side Effects: + * Receive buffers are posted to the adapter LLC queue and the adapter + * is notified. + */ + +static int dfx_rcv_init(DFX_board_t *bp, int get_buffers) + { + int i, j; /* used in for loop */ + + /* + * Since each receive buffer is a single fragment of same length, initialize + * first longword in each receive descriptor for entire LLC Host descriptor + * block. Also initialize second longword in each receive descriptor with + * physical address of receive buffer. We'll always allocate receive + * buffers in powers of 2 so that we can easily fill the 256 entry descriptor + * block and produce new receive buffers by simply updating the receive + * producer index. + * + * Assumptions: + * To support all shipping versions of PDQ, the receive buffer size + * must be mod 128 in length and the physical address must be 128 byte + * aligned. In other words, bits 0-6 of the length and address must + * be zero for the following descriptor field entries to be correct on + * all PDQ-based boards. We guaranteed both requirements during + * driver initialization when we allocated memory for the receive buffers. + */ + + if (get_buffers) { +#ifdef DYNAMIC_BUFFERS + for (i = 0; i < (int)(bp->rcv_bufs_to_post); i++) + for (j = 0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post) + { + struct sk_buff *newskb; + dma_addr_t dma_addr; + + newskb = __netdev_alloc_skb(bp->dev, NEW_SKB_SIZE, + GFP_NOIO); + if (!newskb) + return -ENOMEM; + /* + * align to 128 bytes for compatibility with + * the old EISA boards. + */ + + my_skb_align(newskb, 128); + dma_addr = dma_map_single(bp->bus_dev, + newskb->data, + PI_RCV_DATA_K_SIZE_MAX, + DMA_FROM_DEVICE); + if (dma_mapping_error(bp->bus_dev, dma_addr)) { + dev_kfree_skb(newskb); + return -ENOMEM; + } + bp->descr_block_virt->rcv_data[i + j].long_0 = + (u32)(PI_RCV_DESCR_M_SOP | + ((PI_RCV_DATA_K_SIZE_MAX / + PI_ALIGN_K_RCV_DATA_BUFF) << + PI_RCV_DESCR_V_SEG_LEN)); + bp->descr_block_virt->rcv_data[i + j].long_1 = + (u32)dma_addr; + + /* + * p_rcv_buff_va is only used inside the + * kernel so we put the skb pointer here. + */ + bp->p_rcv_buff_va[i+j] = (char *) newskb; + } +#else + for (i=0; i < (int)(bp->rcv_bufs_to_post); i++) + for (j=0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post) + { + bp->descr_block_virt->rcv_data[i+j].long_0 = (u32) (PI_RCV_DESCR_M_SOP | + ((PI_RCV_DATA_K_SIZE_MAX / PI_ALIGN_K_RCV_DATA_BUFF) << PI_RCV_DESCR_V_SEG_LEN)); + bp->descr_block_virt->rcv_data[i+j].long_1 = (u32) (bp->rcv_block_phys + (i * PI_RCV_DATA_K_SIZE_MAX)); + bp->p_rcv_buff_va[i+j] = (bp->rcv_block_virt + (i * PI_RCV_DATA_K_SIZE_MAX)); + } +#endif + } + + /* Update receive producer and Type 2 register */ + + bp->rcv_xmt_reg.index.rcv_prod = bp->rcv_bufs_to_post; + dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword); + return 0; + } + + +/* + * ========================= + * = dfx_rcv_queue_process = + * ========================= + * + * Overview: + * Process received LLC frames. + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * Received LLC frames are processed until there are no more consumed frames. + * Once all frames are processed, the receive buffers are returned to the + * adapter. Note that this algorithm fixes the length of time that can be spent + * in this routine, because there are a fixed number of receive buffers to + * process and buffers are not produced until this routine exits and returns + * to the ISR. + * + * Return Codes: + * None + * + * Assumptions: + * None + * + * Side Effects: + * None + */ + +static void dfx_rcv_queue_process( + DFX_board_t *bp + ) + + { + PI_TYPE_2_CONSUMER *p_type_2_cons; /* ptr to rcv/xmt consumer block register */ + char *p_buff; /* ptr to start of packet receive buffer (FMC descriptor) */ + u32 descr, pkt_len; /* FMC descriptor field and packet length */ + struct sk_buff *skb = NULL; /* pointer to a sk_buff to hold incoming packet data */ + + /* Service all consumed LLC receive frames */ + + p_type_2_cons = (PI_TYPE_2_CONSUMER *)(&bp->cons_block_virt->xmt_rcv_data); + while (bp->rcv_xmt_reg.index.rcv_comp != p_type_2_cons->index.rcv_cons) + { + /* Process any errors */ + dma_addr_t dma_addr; + int entry; + + entry = bp->rcv_xmt_reg.index.rcv_comp; +#ifdef DYNAMIC_BUFFERS + p_buff = (char *) (((struct sk_buff *)bp->p_rcv_buff_va[entry])->data); +#else + p_buff = bp->p_rcv_buff_va[entry]; +#endif + dma_addr = bp->descr_block_virt->rcv_data[entry].long_1; + dma_sync_single_for_cpu(bp->bus_dev, + dma_addr + RCV_BUFF_K_DESCR, + sizeof(u32), + DMA_FROM_DEVICE); + memcpy(&descr, p_buff + RCV_BUFF_K_DESCR, sizeof(u32)); + + if (descr & PI_FMC_DESCR_M_RCC_FLUSH) + { + if (descr & PI_FMC_DESCR_M_RCC_CRC) + bp->rcv_crc_errors++; + else + bp->rcv_frame_status_errors++; + } + else + { + int rx_in_place = 0; + + /* The frame was received without errors - verify packet length */ + + pkt_len = (u32)((descr & PI_FMC_DESCR_M_LEN) >> PI_FMC_DESCR_V_LEN); + pkt_len -= 4; /* subtract 4 byte CRC */ + if (!IN_RANGE(pkt_len, FDDI_K_LLC_ZLEN, FDDI_K_LLC_LEN)) + bp->rcv_length_errors++; + else{ +#ifdef DYNAMIC_BUFFERS + struct sk_buff *newskb = NULL; + + if (pkt_len > SKBUFF_RX_COPYBREAK) { + dma_addr_t new_dma_addr; + + newskb = netdev_alloc_skb(bp->dev, + NEW_SKB_SIZE); + if (newskb){ + my_skb_align(newskb, 128); + new_dma_addr = dma_map_single( + bp->bus_dev, + newskb->data, + PI_RCV_DATA_K_SIZE_MAX, + DMA_FROM_DEVICE); + if (dma_mapping_error( + bp->bus_dev, + new_dma_addr)) { + dev_kfree_skb(newskb); + newskb = NULL; + } + } + if (newskb) { + rx_in_place = 1; + + skb = (struct sk_buff *)bp->p_rcv_buff_va[entry]; + dma_unmap_single(bp->bus_dev, + dma_addr, + PI_RCV_DATA_K_SIZE_MAX, + DMA_FROM_DEVICE); + skb_reserve(skb, RCV_BUFF_K_PADDING); + bp->p_rcv_buff_va[entry] = (char *)newskb; + bp->descr_block_virt->rcv_data[entry].long_1 = (u32)new_dma_addr; + } + } + if (!newskb) +#endif + /* Alloc new buffer to pass up, + * add room for PRH. */ + skb = netdev_alloc_skb(bp->dev, + pkt_len + 3); + if (skb == NULL) + { + printk("%s: Could not allocate receive buffer. Dropping packet.\n", bp->dev->name); + bp->rcv_discards++; + break; + } + else { + if (!rx_in_place) { + /* Receive buffer allocated, pass receive packet up */ + dma_sync_single_for_cpu( + bp->bus_dev, + dma_addr + + RCV_BUFF_K_PADDING, + pkt_len + 3, + DMA_FROM_DEVICE); + + skb_copy_to_linear_data(skb, + p_buff + RCV_BUFF_K_PADDING, + pkt_len + 3); + } + + skb_reserve(skb,3); /* adjust data field so that it points to FC byte */ + skb_put(skb, pkt_len); /* pass up packet length, NOT including CRC */ + skb->protocol = fddi_type_trans(skb, bp->dev); + bp->rcv_total_bytes += skb->len; + netif_rx(skb); + + /* Update the rcv counters */ + bp->rcv_total_frames++; + if (*(p_buff + RCV_BUFF_K_DA) & 0x01) + bp->rcv_multicast_frames++; + } + } + } + + /* + * Advance the producer (for recycling) and advance the completion + * (for servicing received frames). Note that it is okay to + * advance the producer without checking that it passes the + * completion index because they are both advanced at the same + * rate. + */ + + bp->rcv_xmt_reg.index.rcv_prod += 1; + bp->rcv_xmt_reg.index.rcv_comp += 1; + } + } + + +/* + * ===================== + * = dfx_xmt_queue_pkt = + * ===================== + * + * Overview: + * Queues packets for transmission + * + * Returns: + * Condition code + * + * Arguments: + * skb - pointer to sk_buff to queue for transmission + * dev - pointer to device information + * + * Functional Description: + * Here we assume that an incoming skb transmit request + * is contained in a single physically contiguous buffer + * in which the virtual address of the start of packet + * (skb->data) can be converted to a physical address + * by using pci_map_single(). + * + * Since the adapter architecture requires a three byte + * packet request header to prepend the start of packet, + * we'll write the three byte field immediately prior to + * the FC byte. This assumption is valid because we've + * ensured that dev->hard_header_len includes three pad + * bytes. By posting a single fragment to the adapter, + * we'll reduce the number of descriptor fetches and + * bus traffic needed to send the request. + * + * Also, we can't free the skb until after it's been DMA'd + * out by the adapter, so we'll queue it in the driver and + * return it in dfx_xmt_done. + * + * Return Codes: + * 0 - driver queued packet, link is unavailable, or skbuff was bad + * 1 - caller should requeue the sk_buff for later transmission + * + * Assumptions: + * First and foremost, we assume the incoming skb pointer + * is NOT NULL and is pointing to a valid sk_buff structure. + * + * The outgoing packet is complete, starting with the + * frame control byte including the last byte of data, + * but NOT including the 4 byte CRC. We'll let the + * adapter hardware generate and append the CRC. + * + * The entire packet is stored in one physically + * contiguous buffer which is not cached and whose + * 32-bit physical address can be determined. + * + * It's vital that this routine is NOT reentered for the + * same board and that the OS is not in another section of + * code (eg. dfx_int_common) for the same board on a + * different thread. + * + * Side Effects: + * None + */ + +static netdev_tx_t dfx_xmt_queue_pkt(struct sk_buff *skb, + struct net_device *dev) + { + DFX_board_t *bp = netdev_priv(dev); + u8 prod; /* local transmit producer index */ + PI_XMT_DESCR *p_xmt_descr; /* ptr to transmit descriptor block entry */ + XMT_DRIVER_DESCR *p_xmt_drv_descr; /* ptr to transmit driver descriptor */ + dma_addr_t dma_addr; + unsigned long flags; + + netif_stop_queue(dev); + + /* + * Verify that incoming transmit request is OK + * + * Note: The packet size check is consistent with other + * Linux device drivers, although the correct packet + * size should be verified before calling the + * transmit routine. + */ + + if (!IN_RANGE(skb->len, FDDI_K_LLC_ZLEN, FDDI_K_LLC_LEN)) + { + printk("%s: Invalid packet length - %u bytes\n", + dev->name, skb->len); + bp->xmt_length_errors++; /* bump error counter */ + netif_wake_queue(dev); + dev_kfree_skb(skb); + return NETDEV_TX_OK; /* return "success" */ + } + /* + * See if adapter link is available, if not, free buffer + * + * Note: If the link isn't available, free buffer and return 0 + * rather than tell the upper layer to requeue the packet. + * The methodology here is that by the time the link + * becomes available, the packet to be sent will be + * fairly stale. By simply dropping the packet, the + * higher layer protocols will eventually time out + * waiting for response packets which it won't receive. + */ + + if (bp->link_available == PI_K_FALSE) + { + if (dfx_hw_adap_state_rd(bp) == PI_STATE_K_LINK_AVAIL) /* is link really available? */ + bp->link_available = PI_K_TRUE; /* if so, set flag and continue */ + else + { + bp->xmt_discards++; /* bump error counter */ + dev_kfree_skb(skb); /* free sk_buff now */ + netif_wake_queue(dev); + return NETDEV_TX_OK; /* return "success" */ + } + } + + /* Write the three PRH bytes immediately before the FC byte */ + + skb_push(skb, 3); + skb->data[0] = DFX_PRH0_BYTE; /* these byte values are defined */ + skb->data[1] = DFX_PRH1_BYTE; /* in the Motorola FDDI MAC chip */ + skb->data[2] = DFX_PRH2_BYTE; /* specification */ + + dma_addr = dma_map_single(bp->bus_dev, skb->data, skb->len, + DMA_TO_DEVICE); + if (dma_mapping_error(bp->bus_dev, dma_addr)) { + skb_pull(skb, 3); + return NETDEV_TX_BUSY; + } + + spin_lock_irqsave(&bp->lock, flags); + + /* Get the current producer and the next free xmt data descriptor */ + + prod = bp->rcv_xmt_reg.index.xmt_prod; + p_xmt_descr = &(bp->descr_block_virt->xmt_data[prod]); + + /* + * Get pointer to auxiliary queue entry to contain information + * for this packet. + * + * Note: The current xmt producer index will become the + * current xmt completion index when we complete this + * packet later on. So, we'll get the pointer to the + * next auxiliary queue entry now before we bump the + * producer index. + */ + + p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[prod++]); /* also bump producer index */ + + /* + * Write the descriptor with buffer info and bump producer + * + * Note: Since we need to start DMA from the packet request + * header, we'll add 3 bytes to the DMA buffer length, + * and we'll determine the physical address of the + * buffer from the PRH, not skb->data. + * + * Assumptions: + * 1. Packet starts with the frame control (FC) byte + * at skb->data. + * 2. The 4-byte CRC is not appended to the buffer or + * included in the length. + * 3. Packet length (skb->len) is from FC to end of + * data, inclusive. + * 4. The packet length does not exceed the maximum + * FDDI LLC frame length of 4491 bytes. + * 5. The entire packet is contained in a physically + * contiguous, non-cached, locked memory space + * comprised of a single buffer pointed to by + * skb->data. + * 6. The physical address of the start of packet + * can be determined from the virtual address + * by using pci_map_single() and is only 32-bits + * wide. + */ + + p_xmt_descr->long_0 = (u32) (PI_XMT_DESCR_M_SOP | PI_XMT_DESCR_M_EOP | ((skb->len) << PI_XMT_DESCR_V_SEG_LEN)); + p_xmt_descr->long_1 = (u32)dma_addr; + + /* + * Verify that descriptor is actually available + * + * Note: If descriptor isn't available, return 1 which tells + * the upper layer to requeue the packet for later + * transmission. + * + * We need to ensure that the producer never reaches the + * completion, except to indicate that the queue is empty. + */ + + if (prod == bp->rcv_xmt_reg.index.xmt_comp) + { + skb_pull(skb,3); + spin_unlock_irqrestore(&bp->lock, flags); + return NETDEV_TX_BUSY; /* requeue packet for later */ + } + + /* + * Save info for this packet for xmt done indication routine + * + * Normally, we'd save the producer index in the p_xmt_drv_descr + * structure so that we'd have it handy when we complete this + * packet later (in dfx_xmt_done). However, since the current + * transmit architecture guarantees a single fragment for the + * entire packet, we can simply bump the completion index by + * one (1) for each completed packet. + * + * Note: If this assumption changes and we're presented with + * an inconsistent number of transmit fragments for packet + * data, we'll need to modify this code to save the current + * transmit producer index. + */ + + p_xmt_drv_descr->p_skb = skb; + + /* Update Type 2 register */ + + bp->rcv_xmt_reg.index.xmt_prod = prod; + dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword); + spin_unlock_irqrestore(&bp->lock, flags); + netif_wake_queue(dev); + return NETDEV_TX_OK; /* packet queued to adapter */ + } + + +/* + * ================ + * = dfx_xmt_done = + * ================ + * + * Overview: + * Processes all frames that have been transmitted. + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * For all consumed transmit descriptors that have not + * yet been completed, we'll free the skb we were holding + * onto using dev_kfree_skb and bump the appropriate + * counters. + * + * Return Codes: + * None + * + * Assumptions: + * The Type 2 register is not updated in this routine. It is + * assumed that it will be updated in the ISR when dfx_xmt_done + * returns. + * + * Side Effects: + * None + */ + +static int dfx_xmt_done(DFX_board_t *bp) + { + XMT_DRIVER_DESCR *p_xmt_drv_descr; /* ptr to transmit driver descriptor */ + PI_TYPE_2_CONSUMER *p_type_2_cons; /* ptr to rcv/xmt consumer block register */ + u8 comp; /* local transmit completion index */ + int freed = 0; /* buffers freed */ + + /* Service all consumed transmit frames */ + + p_type_2_cons = (PI_TYPE_2_CONSUMER *)(&bp->cons_block_virt->xmt_rcv_data); + while (bp->rcv_xmt_reg.index.xmt_comp != p_type_2_cons->index.xmt_cons) + { + /* Get pointer to the transmit driver descriptor block information */ + + p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[bp->rcv_xmt_reg.index.xmt_comp]); + + /* Increment transmit counters */ + + bp->xmt_total_frames++; + bp->xmt_total_bytes += p_xmt_drv_descr->p_skb->len; + + /* Return skb to operating system */ + comp = bp->rcv_xmt_reg.index.xmt_comp; + dma_unmap_single(bp->bus_dev, + bp->descr_block_virt->xmt_data[comp].long_1, + p_xmt_drv_descr->p_skb->len, + DMA_TO_DEVICE); + dev_kfree_skb_irq(p_xmt_drv_descr->p_skb); + + /* + * Move to start of next packet by updating completion index + * + * Here we assume that a transmit packet request is always + * serviced by posting one fragment. We can therefore + * simplify the completion code by incrementing the + * completion index by one. This code will need to be + * modified if this assumption changes. See comments + * in dfx_xmt_queue_pkt for more details. + */ + + bp->rcv_xmt_reg.index.xmt_comp += 1; + freed++; + } + return freed; + } + + +/* + * ================= + * = dfx_rcv_flush = + * ================= + * + * Overview: + * Remove all skb's in the receive ring. + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * Free's all the dynamically allocated skb's that are + * currently attached to the device receive ring. This + * function is typically only used when the device is + * initialized or reinitialized. + * + * Return Codes: + * None + * + * Side Effects: + * None + */ +#ifdef DYNAMIC_BUFFERS +static void dfx_rcv_flush( DFX_board_t *bp ) + { + int i, j; + + for (i = 0; i < (int)(bp->rcv_bufs_to_post); i++) + for (j = 0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post) + { + struct sk_buff *skb; + skb = (struct sk_buff *)bp->p_rcv_buff_va[i+j]; + if (skb) { + dma_unmap_single(bp->bus_dev, + bp->descr_block_virt->rcv_data[i+j].long_1, + PI_RCV_DATA_K_SIZE_MAX, + DMA_FROM_DEVICE); + dev_kfree_skb(skb); + } + bp->p_rcv_buff_va[i+j] = NULL; + } + + } +#endif /* DYNAMIC_BUFFERS */ + +/* + * ================= + * = dfx_xmt_flush = + * ================= + * + * Overview: + * Processes all frames whether they've been transmitted + * or not. + * + * Returns: + * None + * + * Arguments: + * bp - pointer to board information + * + * Functional Description: + * For all produced transmit descriptors that have not + * yet been completed, we'll free the skb we were holding + * onto using dev_kfree_skb and bump the appropriate + * counters. Of course, it's possible that some of + * these transmit requests actually did go out, but we + * won't make that distinction here. Finally, we'll + * update the consumer index to match the producer. + * + * Return Codes: + * None + * + * Assumptions: + * This routine does NOT update the Type 2 register. It + * is assumed that this routine is being called during a + * transmit flush interrupt, or a shutdown or close routine. + * + * Side Effects: + * None + */ + +static void dfx_xmt_flush( DFX_board_t *bp ) + { + u32 prod_cons; /* rcv/xmt consumer block longword */ + XMT_DRIVER_DESCR *p_xmt_drv_descr; /* ptr to transmit driver descriptor */ + u8 comp; /* local transmit completion index */ + + /* Flush all outstanding transmit frames */ + + while (bp->rcv_xmt_reg.index.xmt_comp != bp->rcv_xmt_reg.index.xmt_prod) + { + /* Get pointer to the transmit driver descriptor block information */ + + p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[bp->rcv_xmt_reg.index.xmt_comp]); + + /* Return skb to operating system */ + comp = bp->rcv_xmt_reg.index.xmt_comp; + dma_unmap_single(bp->bus_dev, + bp->descr_block_virt->xmt_data[comp].long_1, + p_xmt_drv_descr->p_skb->len, + DMA_TO_DEVICE); + dev_kfree_skb(p_xmt_drv_descr->p_skb); + + /* Increment transmit error counter */ + + bp->xmt_discards++; + + /* + * Move to start of next packet by updating completion index + * + * Here we assume that a transmit packet request is always + * serviced by posting one fragment. We can therefore + * simplify the completion code by incrementing the + * completion index by one. This code will need to be + * modified if this assumption changes. See comments + * in dfx_xmt_queue_pkt for more details. + */ + + bp->rcv_xmt_reg.index.xmt_comp += 1; + } + + /* Update the transmit consumer index in the consumer block */ + + prod_cons = (u32)(bp->cons_block_virt->xmt_rcv_data & ~PI_CONS_M_XMT_INDEX); + prod_cons |= (u32)(bp->rcv_xmt_reg.index.xmt_prod << PI_CONS_V_XMT_INDEX); + bp->cons_block_virt->xmt_rcv_data = prod_cons; + } + +/* + * ================== + * = dfx_unregister = + * ================== + * + * Overview: + * Shuts down an FDDI controller + * + * Returns: + * Condition code + * + * Arguments: + * bdev - pointer to device information + * + * Functional Description: + * + * Return Codes: + * None + * + * Assumptions: + * It compiles so it should work :-( (PCI cards do :-) + * + * Side Effects: + * Device structures for FDDI adapters (fddi0, fddi1, etc) are + * freed. + */ +static void dfx_unregister(struct device *bdev) +{ + struct net_device *dev = dev_get_drvdata(bdev); + DFX_board_t *bp = netdev_priv(dev); + int dfx_bus_pci = dev_is_pci(bdev); + int dfx_bus_tc = DFX_BUS_TC(bdev); + int dfx_use_mmio = DFX_MMIO || dfx_bus_tc; + resource_size_t bar_start[3]; /* pointers to ports */ + resource_size_t bar_len[3]; /* resource lengths */ + int alloc_size; /* total buffer size used */ + + unregister_netdev(dev); + + alloc_size = sizeof(PI_DESCR_BLOCK) + + PI_CMD_REQ_K_SIZE_MAX + PI_CMD_RSP_K_SIZE_MAX + +#ifndef DYNAMIC_BUFFERS + (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) + +#endif + sizeof(PI_CONSUMER_BLOCK) + + (PI_ALIGN_K_DESC_BLK - 1); + if (bp->kmalloced) + dma_free_coherent(bdev, alloc_size, + bp->kmalloced, bp->kmalloced_dma); + + dfx_bus_uninit(dev); + + dfx_get_bars(bdev, bar_start, bar_len); + if (bar_start[2] != 0) + release_region(bar_start[2], bar_len[2]); + if (bar_start[1] != 0) + release_region(bar_start[1], bar_len[1]); + if (dfx_use_mmio) { + iounmap(bp->base.mem); + release_mem_region(bar_start[0], bar_len[0]); + } else + release_region(bar_start[0], bar_len[0]); + + if (dfx_bus_pci) + pci_disable_device(to_pci_dev(bdev)); + + free_netdev(dev); +} + + +static int __maybe_unused dfx_dev_register(struct device *); +static int __maybe_unused dfx_dev_unregister(struct device *); + +#ifdef CONFIG_PCI +static int dfx_pci_register(struct pci_dev *, const struct pci_device_id *); +static void dfx_pci_unregister(struct pci_dev *); + +static const struct pci_device_id dfx_pci_table[] = { + { PCI_DEVICE(PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_FDDI) }, + { } +}; +MODULE_DEVICE_TABLE(pci, dfx_pci_table); + +static struct pci_driver dfx_pci_driver = { + .name = "defxx", + .id_table = dfx_pci_table, + .probe = dfx_pci_register, + .remove = dfx_pci_unregister, +}; + +static int dfx_pci_register(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + return dfx_register(&pdev->dev); +} + +static void dfx_pci_unregister(struct pci_dev *pdev) +{ + dfx_unregister(&pdev->dev); +} +#endif /* CONFIG_PCI */ + +#ifdef CONFIG_EISA +static struct eisa_device_id dfx_eisa_table[] = { + { "DEC3001", DEFEA_PROD_ID_1 }, + { "DEC3002", DEFEA_PROD_ID_2 }, + { "DEC3003", DEFEA_PROD_ID_3 }, + { "DEC3004", DEFEA_PROD_ID_4 }, + { } +}; +MODULE_DEVICE_TABLE(eisa, dfx_eisa_table); + +static struct eisa_driver dfx_eisa_driver = { + .id_table = dfx_eisa_table, + .driver = { + .name = "defxx", + .bus = &eisa_bus_type, + .probe = dfx_dev_register, + .remove = dfx_dev_unregister, + }, +}; +#endif /* CONFIG_EISA */ + +#ifdef CONFIG_TC +static struct tc_device_id const dfx_tc_table[] = { + { "DEC ", "PMAF-FA " }, + { "DEC ", "PMAF-FD " }, + { "DEC ", "PMAF-FS " }, + { "DEC ", "PMAF-FU " }, + { } +}; +MODULE_DEVICE_TABLE(tc, dfx_tc_table); + +static struct tc_driver dfx_tc_driver = { + .id_table = dfx_tc_table, + .driver = { + .name = "defxx", + .bus = &tc_bus_type, + .probe = dfx_dev_register, + .remove = dfx_dev_unregister, + }, +}; +#endif /* CONFIG_TC */ + +static int __maybe_unused dfx_dev_register(struct device *dev) +{ + int status; + + status = dfx_register(dev); + if (!status) + get_device(dev); + return status; +} + +static int __maybe_unused dfx_dev_unregister(struct device *dev) +{ + put_device(dev); + dfx_unregister(dev); + return 0; +} + + +static int dfx_init(void) +{ + int status; + + status = pci_register_driver(&dfx_pci_driver); + if (!status) + status = eisa_driver_register(&dfx_eisa_driver); + if (!status) + status = tc_register_driver(&dfx_tc_driver); + return status; +} + +static void dfx_cleanup(void) +{ + tc_unregister_driver(&dfx_tc_driver); + eisa_driver_unregister(&dfx_eisa_driver); + pci_unregister_driver(&dfx_pci_driver); +} + +module_init(dfx_init); +module_exit(dfx_cleanup); +MODULE_AUTHOR("Lawrence V. Stefani"); +MODULE_DESCRIPTION("DEC FDDIcontroller TC/EISA/PCI (DEFTA/DEFEA/DEFPA) driver " + DRV_VERSION " " DRV_RELDATE); +MODULE_LICENSE("GPL"); diff --git a/kernel/drivers/net/fddi/defxx.h b/kernel/drivers/net/fddi/defxx.h new file mode 100644 index 000000000..9d30fde2e --- /dev/null +++ b/kernel/drivers/net/fddi/defxx.h @@ -0,0 +1,1803 @@ +/* + * File Name: + * defxx.h + * + * Copyright Information: + * Copyright Digital Equipment Corporation 1996. + * + * This software may be used and distributed according to the terms of + * the GNU General Public License, incorporated herein by reference. + * + * Abstract: + * Contains all definitions specified by port specification and required + * by the defxx.c driver. + * + * The original author: + * LVS Lawrence V. Stefani <lstefani@yahoo.com> + * + * Maintainers: + * macro Maciej W. Rozycki <macro@linux-mips.org> + * + * Modification History: + * Date Name Description + * 16-Aug-96 LVS Created. + * 09-Sep-96 LVS Added group_prom field. Moved read/write I/O + * macros to DEFXX.C. + * 12-Sep-96 LVS Removed packet request header pointers. + * 04 Aug 2003 macro Converted to the DMA API. + * 23 Oct 2006 macro Big-endian host support. + * 14 Dec 2006 macro TURBOchannel support. + */ + +#ifndef _DEFXX_H_ +#define _DEFXX_H_ + +/* Define basic types for unsigned chars, shorts, longs */ + +typedef u8 PI_UINT8; +typedef u16 PI_UINT16; +typedef u32 PI_UINT32; + +/* Define general structures */ + +typedef struct /* 64-bit counter */ + { + PI_UINT32 ms; + PI_UINT32 ls; + } PI_CNTR; + +typedef struct /* LAN address */ + { + PI_UINT32 lwrd_0; + PI_UINT32 lwrd_1; + } PI_LAN_ADDR; + +typedef struct /* Station ID address */ + { + PI_UINT32 octet_7_4; + PI_UINT32 octet_3_0; + } PI_STATION_ID; + + +/* Define general constants */ + +#define PI_ALIGN_K_DESC_BLK 8192 /* Descriptor block boundary */ +#define PI_ALIGN_K_CONS_BLK 64 /* Consumer block boundary */ +#define PI_ALIGN_K_CMD_REQ_BUFF 128 /* Xmt Command que buffer alignment */ +#define PI_ALIGN_K_CMD_RSP_BUFF 128 /* Rcv Command que buffer alignment */ +#define PI_ALIGN_K_UNSOL_BUFF 128 /* Unsol que buffer alignment */ +#define PI_ALIGN_K_XMT_DATA_BUFF 0 /* Xmt data que buffer alignment */ +#define PI_ALIGN_K_RCV_DATA_BUFF 128 /* Rcv que buffer alignment */ + +/* Define PHY index values */ + +#define PI_PHY_K_S 0 /* Index to S phy */ +#define PI_PHY_K_A 0 /* Index to A phy */ +#define PI_PHY_K_B 1 /* Index to B phy */ +#define PI_PHY_K_MAX 2 /* Max number of phys */ + +/* Define FMC descriptor fields */ + +#define PI_FMC_DESCR_V_SOP 31 +#define PI_FMC_DESCR_V_EOP 30 +#define PI_FMC_DESCR_V_FSC 27 +#define PI_FMC_DESCR_V_FSB_ERROR 26 +#define PI_FMC_DESCR_V_FSB_ADDR_RECOG 25 +#define PI_FMC_DESCR_V_FSB_ADDR_COPIED 24 +#define PI_FMC_DESCR_V_FSB 22 +#define PI_FMC_DESCR_V_RCC_FLUSH 21 +#define PI_FMC_DESCR_V_RCC_CRC 20 +#define PI_FMC_DESCR_V_RCC_RRR 17 +#define PI_FMC_DESCR_V_RCC_DD 15 +#define PI_FMC_DESCR_V_RCC_SS 13 +#define PI_FMC_DESCR_V_RCC 13 +#define PI_FMC_DESCR_V_LEN 0 + +#define PI_FMC_DESCR_M_SOP 0x80000000 +#define PI_FMC_DESCR_M_EOP 0x40000000 +#define PI_FMC_DESCR_M_FSC 0x38000000 +#define PI_FMC_DESCR_M_FSB_ERROR 0x04000000 +#define PI_FMC_DESCR_M_FSB_ADDR_RECOG 0x02000000 +#define PI_FMC_DESCR_M_FSB_ADDR_COPIED 0x01000000 +#define PI_FMC_DESCR_M_FSB 0x07C00000 +#define PI_FMC_DESCR_M_RCC_FLUSH 0x00200000 +#define PI_FMC_DESCR_M_RCC_CRC 0x00100000 +#define PI_FMC_DESCR_M_RCC_RRR 0x000E0000 +#define PI_FMC_DESCR_M_RCC_DD 0x00018000 +#define PI_FMC_DESCR_M_RCC_SS 0x00006000 +#define PI_FMC_DESCR_M_RCC 0x003FE000 +#define PI_FMC_DESCR_M_LEN 0x00001FFF + +#define PI_FMC_DESCR_K_RCC_FMC_INT_ERR 0x01AA + +#define PI_FMC_DESCR_K_RRR_SUCCESS 0x00 +#define PI_FMC_DESCR_K_RRR_SA_MATCH 0x01 +#define PI_FMC_DESCR_K_RRR_DA_MATCH 0x02 +#define PI_FMC_DESCR_K_RRR_FMC_ABORT 0x03 +#define PI_FMC_DESCR_K_RRR_LENGTH_BAD 0x04 +#define PI_FMC_DESCR_K_RRR_FRAGMENT 0x05 +#define PI_FMC_DESCR_K_RRR_FORMAT_ERR 0x06 +#define PI_FMC_DESCR_K_RRR_MAC_RESET 0x07 + +#define PI_FMC_DESCR_K_DD_NO_MATCH 0x0 +#define PI_FMC_DESCR_K_DD_PROMISCUOUS 0x1 +#define PI_FMC_DESCR_K_DD_CAM_MATCH 0x2 +#define PI_FMC_DESCR_K_DD_LOCAL_MATCH 0x3 + +#define PI_FMC_DESCR_K_SS_NO_MATCH 0x0 +#define PI_FMC_DESCR_K_SS_BRIDGE_MATCH 0x1 +#define PI_FMC_DESCR_K_SS_NOT_POSSIBLE 0x2 +#define PI_FMC_DESCR_K_SS_LOCAL_MATCH 0x3 + +/* Define some max buffer sizes */ + +#define PI_CMD_REQ_K_SIZE_MAX 512 +#define PI_CMD_RSP_K_SIZE_MAX 512 +#define PI_UNSOL_K_SIZE_MAX 512 +#define PI_SMT_HOST_K_SIZE_MAX 4608 /* 4 1/2 K */ +#define PI_RCV_DATA_K_SIZE_MAX 4608 /* 4 1/2 K */ +#define PI_XMT_DATA_K_SIZE_MAX 4608 /* 4 1/2 K */ + +/* Define adapter states */ + +#define PI_STATE_K_RESET 0 +#define PI_STATE_K_UPGRADE 1 +#define PI_STATE_K_DMA_UNAVAIL 2 +#define PI_STATE_K_DMA_AVAIL 3 +#define PI_STATE_K_LINK_AVAIL 4 +#define PI_STATE_K_LINK_UNAVAIL 5 +#define PI_STATE_K_HALTED 6 +#define PI_STATE_K_RING_MEMBER 7 +#define PI_STATE_K_NUMBER 8 + +/* Define codes for command type */ + +#define PI_CMD_K_START 0x00 +#define PI_CMD_K_FILTERS_SET 0x01 +#define PI_CMD_K_FILTERS_GET 0x02 +#define PI_CMD_K_CHARS_SET 0x03 +#define PI_CMD_K_STATUS_CHARS_GET 0x04 +#define PI_CMD_K_CNTRS_GET 0x05 +#define PI_CMD_K_CNTRS_SET 0x06 +#define PI_CMD_K_ADDR_FILTER_SET 0x07 +#define PI_CMD_K_ADDR_FILTER_GET 0x08 +#define PI_CMD_K_ERROR_LOG_CLEAR 0x09 +#define PI_CMD_K_ERROR_LOG_GET 0x0A +#define PI_CMD_K_FDDI_MIB_GET 0x0B +#define PI_CMD_K_DEC_EXT_MIB_GET 0x0C +#define PI_CMD_K_DEVICE_SPECIFIC_GET 0x0D +#define PI_CMD_K_SNMP_SET 0x0E +#define PI_CMD_K_UNSOL_TEST 0x0F +#define PI_CMD_K_SMT_MIB_GET 0x10 +#define PI_CMD_K_SMT_MIB_SET 0x11 +#define PI_CMD_K_MAX 0x11 /* Must match last */ + +/* Define item codes for Chars_Set and Filters_Set commands */ + +#define PI_ITEM_K_EOL 0x00 /* End-of-Item list */ +#define PI_ITEM_K_T_REQ 0x01 /* DECnet T_REQ */ +#define PI_ITEM_K_TVX 0x02 /* DECnet TVX */ +#define PI_ITEM_K_RESTRICTED_TOKEN 0x03 /* DECnet Restricted Token */ +#define PI_ITEM_K_LEM_THRESHOLD 0x04 /* DECnet LEM Threshold */ +#define PI_ITEM_K_RING_PURGER 0x05 /* DECnet Ring Purger Enable */ +#define PI_ITEM_K_CNTR_INTERVAL 0x06 /* Chars_Set */ +#define PI_ITEM_K_IND_GROUP_PROM 0x07 /* Filters_Set */ +#define PI_ITEM_K_GROUP_PROM 0x08 /* Filters_Set */ +#define PI_ITEM_K_BROADCAST 0x09 /* Filters_Set */ +#define PI_ITEM_K_SMT_PROM 0x0A /* Filters_Set */ +#define PI_ITEM_K_SMT_USER 0x0B /* Filters_Set */ +#define PI_ITEM_K_RESERVED 0x0C /* Filters_Set */ +#define PI_ITEM_K_IMPLEMENTOR 0x0D /* Filters_Set */ +#define PI_ITEM_K_LOOPBACK_MODE 0x0E /* Chars_Set */ +#define PI_ITEM_K_CONFIG_POLICY 0x10 /* SMTConfigPolicy */ +#define PI_ITEM_K_CON_POLICY 0x11 /* SMTConnectionPolicy */ +#define PI_ITEM_K_T_NOTIFY 0x12 /* SMTTNotify */ +#define PI_ITEM_K_STATION_ACTION 0x13 /* SMTStationAction */ +#define PI_ITEM_K_MAC_PATHS_REQ 0x15 /* MACPathsRequested */ +#define PI_ITEM_K_MAC_ACTION 0x17 /* MACAction */ +#define PI_ITEM_K_CON_POLICIES 0x18 /* PORTConnectionPolicies */ +#define PI_ITEM_K_PORT_PATHS_REQ 0x19 /* PORTPathsRequested */ +#define PI_ITEM_K_MAC_LOOP_TIME 0x1A /* PORTMACLoopTime */ +#define PI_ITEM_K_TB_MAX 0x1B /* PORTTBMax */ +#define PI_ITEM_K_LER_CUTOFF 0x1C /* PORTLerCutoff */ +#define PI_ITEM_K_LER_ALARM 0x1D /* PORTLerAlarm */ +#define PI_ITEM_K_PORT_ACTION 0x1E /* PORTAction */ +#define PI_ITEM_K_FLUSH_TIME 0x20 /* Chars_Set */ +#define PI_ITEM_K_MAC_T_REQ 0x29 /* MACTReq */ +#define PI_ITEM_K_EMAC_RING_PURGER 0x2A /* eMACRingPurgerEnable */ +#define PI_ITEM_K_EMAC_RTOKEN_TIMEOUT 0x2B /* eMACRestrictedTokenTimeout */ +#define PI_ITEM_K_FDX_ENB_DIS 0x2C /* eFDXEnable */ +#define PI_ITEM_K_MAX 0x2C /* Must equal high item */ + +/* Values for some of the items */ + +#define PI_K_FALSE 0 /* Generic false */ +#define PI_K_TRUE 1 /* Generic true */ + +#define PI_SNMP_K_TRUE 1 /* SNMP true/false values */ +#define PI_SNMP_K_FALSE 2 + +#define PI_FSTATE_K_BLOCK 0 /* Filter State */ +#define PI_FSTATE_K_PASS 1 + +/* Define command return codes */ + +#define PI_RSP_K_SUCCESS 0x00 +#define PI_RSP_K_FAILURE 0x01 +#define PI_RSP_K_WARNING 0x02 +#define PI_RSP_K_LOOP_MODE_BAD 0x03 +#define PI_RSP_K_ITEM_CODE_BAD 0x04 +#define PI_RSP_K_TVX_BAD 0x05 +#define PI_RSP_K_TREQ_BAD 0x06 +#define PI_RSP_K_TOKEN_BAD 0x07 +#define PI_RSP_K_NO_EOL 0x0C +#define PI_RSP_K_FILTER_STATE_BAD 0x0D +#define PI_RSP_K_CMD_TYPE_BAD 0x0E +#define PI_RSP_K_ADAPTER_STATE_BAD 0x0F +#define PI_RSP_K_RING_PURGER_BAD 0x10 +#define PI_RSP_K_LEM_THRESHOLD_BAD 0x11 +#define PI_RSP_K_LOOP_NOT_SUPPORTED 0x12 +#define PI_RSP_K_FLUSH_TIME_BAD 0x13 +#define PI_RSP_K_NOT_IMPLEMENTED 0x14 +#define PI_RSP_K_CONFIG_POLICY_BAD 0x15 +#define PI_RSP_K_STATION_ACTION_BAD 0x16 +#define PI_RSP_K_MAC_ACTION_BAD 0x17 +#define PI_RSP_K_CON_POLICIES_BAD 0x18 +#define PI_RSP_K_MAC_LOOP_TIME_BAD 0x19 +#define PI_RSP_K_TB_MAX_BAD 0x1A +#define PI_RSP_K_LER_CUTOFF_BAD 0x1B +#define PI_RSP_K_LER_ALARM_BAD 0x1C +#define PI_RSP_K_MAC_PATHS_REQ_BAD 0x1D +#define PI_RSP_K_MAC_T_REQ_BAD 0x1E +#define PI_RSP_K_EMAC_RING_PURGER_BAD 0x1F +#define PI_RSP_K_EMAC_RTOKEN_TIME_BAD 0x20 +#define PI_RSP_K_NO_SUCH_ENTRY 0x21 +#define PI_RSP_K_T_NOTIFY_BAD 0x22 +#define PI_RSP_K_TR_MAX_EXP_BAD 0x23 +#define PI_RSP_K_MAC_FRM_ERR_THR_BAD 0x24 +#define PI_RSP_K_MAX_T_REQ_BAD 0x25 +#define PI_RSP_K_FDX_ENB_DIS_BAD 0x26 +#define PI_RSP_K_ITEM_INDEX_BAD 0x27 +#define PI_RSP_K_PORT_ACTION_BAD 0x28 + +/* Commonly used structures */ + +typedef struct /* Item list */ + { + PI_UINT32 item_code; + PI_UINT32 value; + } PI_ITEM_LIST; + +typedef struct /* Response header */ + { + PI_UINT32 reserved; + PI_UINT32 cmd_type; + PI_UINT32 status; + } PI_RSP_HEADER; + + +/* Start Command */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_START_REQ; + +/* Start Response */ + +typedef struct + { + PI_RSP_HEADER header; + } PI_CMD_START_RSP; + +/* Filters_Set Request */ + +#define PI_CMD_FILTERS_SET_K_ITEMS_MAX 63 /* Fits in a 512 byte buffer */ + +typedef struct + { + PI_UINT32 cmd_type; + PI_ITEM_LIST item[PI_CMD_FILTERS_SET_K_ITEMS_MAX]; + } PI_CMD_FILTERS_SET_REQ; + +/* Filters_Set Response */ + +typedef struct + { + PI_RSP_HEADER header; + } PI_CMD_FILTERS_SET_RSP; + +/* Filters_Get Request */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_FILTERS_GET_REQ; + +/* Filters_Get Response */ + +typedef struct + { + PI_RSP_HEADER header; + PI_UINT32 ind_group_prom; + PI_UINT32 group_prom; + PI_UINT32 broadcast_all; + PI_UINT32 smt_all; + PI_UINT32 smt_user; + PI_UINT32 reserved_all; + PI_UINT32 implementor_all; + } PI_CMD_FILTERS_GET_RSP; + + +/* Chars_Set Request */ + +#define PI_CMD_CHARS_SET_K_ITEMS_MAX 42 /* Fits in a 512 byte buffer */ + +typedef struct + { + PI_UINT32 cmd_type; + struct /* Item list */ + { + PI_UINT32 item_code; + PI_UINT32 value; + PI_UINT32 item_index; + } item[PI_CMD_CHARS_SET_K_ITEMS_MAX]; + } PI_CMD_CHARS_SET_REQ; + +/* Chars_Set Response */ + +typedef struct + { + PI_RSP_HEADER header; + } PI_CMD_CHARS_SET_RSP; + + +/* SNMP_Set Request */ + +#define PI_CMD_SNMP_SET_K_ITEMS_MAX 42 /* Fits in a 512 byte buffer */ + +typedef struct + { + PI_UINT32 cmd_type; + struct /* Item list */ + { + PI_UINT32 item_code; + PI_UINT32 value; + PI_UINT32 item_index; + } item[PI_CMD_SNMP_SET_K_ITEMS_MAX]; + } PI_CMD_SNMP_SET_REQ; + +/* SNMP_Set Response */ + +typedef struct + { + PI_RSP_HEADER header; + } PI_CMD_SNMP_SET_RSP; + + +/* SMT_MIB_Set Request */ + +#define PI_CMD_SMT_MIB_SET_K_ITEMS_MAX 42 /* Max number of items */ + +typedef struct + { + PI_UINT32 cmd_type; + struct + { + PI_UINT32 item_code; + PI_UINT32 value; + PI_UINT32 item_index; + } item[PI_CMD_SMT_MIB_SET_K_ITEMS_MAX]; + } PI_CMD_SMT_MIB_SET_REQ; + +/* SMT_MIB_Set Response */ + +typedef struct + { + PI_RSP_HEADER header; + } PI_CMD_SMT_MIB_SET_RSP; + +/* SMT_MIB_Get Request */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_SMT_MIB_GET_REQ; + +/* SMT_MIB_Get Response */ + +typedef struct /* Refer to ANSI FDDI SMT Rev. 7.3 */ + { + PI_RSP_HEADER header; + + /* SMT GROUP */ + + PI_STATION_ID smt_station_id; + PI_UINT32 smt_op_version_id; + PI_UINT32 smt_hi_version_id; + PI_UINT32 smt_lo_version_id; + PI_UINT32 smt_user_data[8]; + PI_UINT32 smt_mib_version_id; + PI_UINT32 smt_mac_ct; + PI_UINT32 smt_non_master_ct; + PI_UINT32 smt_master_ct; + PI_UINT32 smt_available_paths; + PI_UINT32 smt_config_capabilities; + PI_UINT32 smt_config_policy; + PI_UINT32 smt_connection_policy; + PI_UINT32 smt_t_notify; + PI_UINT32 smt_stat_rpt_policy; + PI_UINT32 smt_trace_max_expiration; + PI_UINT32 smt_bypass_present; + PI_UINT32 smt_ecm_state; + PI_UINT32 smt_cf_state; + PI_UINT32 smt_remote_disconnect_flag; + PI_UINT32 smt_station_status; + PI_UINT32 smt_peer_wrap_flag; + PI_CNTR smt_msg_time_stamp; + PI_CNTR smt_transition_time_stamp; + + /* MAC GROUP */ + + PI_UINT32 mac_frame_status_functions; + PI_UINT32 mac_t_max_capability; + PI_UINT32 mac_tvx_capability; + PI_UINT32 mac_available_paths; + PI_UINT32 mac_current_path; + PI_LAN_ADDR mac_upstream_nbr; + PI_LAN_ADDR mac_downstream_nbr; + PI_LAN_ADDR mac_old_upstream_nbr; + PI_LAN_ADDR mac_old_downstream_nbr; + PI_UINT32 mac_dup_address_test; + PI_UINT32 mac_requested_paths; + PI_UINT32 mac_downstream_port_type; + PI_LAN_ADDR mac_smt_address; + PI_UINT32 mac_t_req; + PI_UINT32 mac_t_neg; + PI_UINT32 mac_t_max; + PI_UINT32 mac_tvx_value; + PI_UINT32 mac_frame_error_threshold; + PI_UINT32 mac_frame_error_ratio; + PI_UINT32 mac_rmt_state; + PI_UINT32 mac_da_flag; + PI_UINT32 mac_unda_flag; + PI_UINT32 mac_frame_error_flag; + PI_UINT32 mac_ma_unitdata_available; + PI_UINT32 mac_hardware_present; + PI_UINT32 mac_ma_unitdata_enable; + + /* PATH GROUP */ + + PI_UINT32 path_configuration[8]; + PI_UINT32 path_tvx_lower_bound; + PI_UINT32 path_t_max_lower_bound; + PI_UINT32 path_max_t_req; + + /* PORT GROUP */ + + PI_UINT32 port_my_type[PI_PHY_K_MAX]; + PI_UINT32 port_neighbor_type[PI_PHY_K_MAX]; + PI_UINT32 port_connection_policies[PI_PHY_K_MAX]; + PI_UINT32 port_mac_indicated[PI_PHY_K_MAX]; + PI_UINT32 port_current_path[PI_PHY_K_MAX]; + PI_UINT32 port_requested_paths[PI_PHY_K_MAX]; + PI_UINT32 port_mac_placement[PI_PHY_K_MAX]; + PI_UINT32 port_available_paths[PI_PHY_K_MAX]; + PI_UINT32 port_pmd_class[PI_PHY_K_MAX]; + PI_UINT32 port_connection_capabilities[PI_PHY_K_MAX]; + PI_UINT32 port_bs_flag[PI_PHY_K_MAX]; + PI_UINT32 port_ler_estimate[PI_PHY_K_MAX]; + PI_UINT32 port_ler_cutoff[PI_PHY_K_MAX]; + PI_UINT32 port_ler_alarm[PI_PHY_K_MAX]; + PI_UINT32 port_connect_state[PI_PHY_K_MAX]; + PI_UINT32 port_pcm_state[PI_PHY_K_MAX]; + PI_UINT32 port_pc_withhold[PI_PHY_K_MAX]; + PI_UINT32 port_ler_flag[PI_PHY_K_MAX]; + PI_UINT32 port_hardware_present[PI_PHY_K_MAX]; + + /* GROUP for things that were added later, so must be at the end. */ + + PI_CNTR path_ring_latency; + + } PI_CMD_SMT_MIB_GET_RSP; + + +/* + * Item and group code definitions for SMT 7.3 mandatory objects. These + * definitions are to be used as appropriate in SMT_MIB_SET commands and + * certain host-sent SMT frames such as PMF Get and Set requests. The + * codes have been taken from the MIB summary section of ANSI SMT 7.3. + */ + +#define PI_GRP_K_SMT_STATION_ID 0x100A +#define PI_ITEM_K_SMT_STATION_ID 0x100B +#define PI_ITEM_K_SMT_OP_VERS_ID 0x100D +#define PI_ITEM_K_SMT_HI_VERS_ID 0x100E +#define PI_ITEM_K_SMT_LO_VERS_ID 0x100F +#define PI_ITEM_K_SMT_USER_DATA 0x1011 +#define PI_ITEM_K_SMT_MIB_VERS_ID 0x1012 + +#define PI_GRP_K_SMT_STATION_CONFIG 0x1014 +#define PI_ITEM_K_SMT_MAC_CT 0x1015 +#define PI_ITEM_K_SMT_NON_MASTER_CT 0x1016 +#define PI_ITEM_K_SMT_MASTER_CT 0x1017 +#define PI_ITEM_K_SMT_AVAIL_PATHS 0x1018 +#define PI_ITEM_K_SMT_CONFIG_CAPS 0x1019 +#define PI_ITEM_K_SMT_CONFIG_POL 0x101A +#define PI_ITEM_K_SMT_CONN_POL 0x101B +#define PI_ITEM_K_SMT_T_NOTIFY 0x101D +#define PI_ITEM_K_SMT_STAT_POL 0x101E +#define PI_ITEM_K_SMT_TR_MAX_EXP 0x101F +#define PI_ITEM_K_SMT_PORT_INDEXES 0x1020 +#define PI_ITEM_K_SMT_MAC_INDEXES 0x1021 +#define PI_ITEM_K_SMT_BYPASS_PRESENT 0x1022 + +#define PI_GRP_K_SMT_STATUS 0x1028 +#define PI_ITEM_K_SMT_ECM_STATE 0x1029 +#define PI_ITEM_K_SMT_CF_STATE 0x102A +#define PI_ITEM_K_SMT_REM_DISC_FLAG 0x102C +#define PI_ITEM_K_SMT_STATION_STATUS 0x102D +#define PI_ITEM_K_SMT_PEER_WRAP_FLAG 0x102E + +#define PI_GRP_K_SMT_MIB_OPERATION 0x1032 +#define PI_ITEM_K_SMT_MSG_TIME_STAMP 0x1033 +#define PI_ITEM_K_SMT_TRN_TIME_STAMP 0x1034 + +#define PI_ITEM_K_SMT_STATION_ACT 0x103C + +#define PI_GRP_K_MAC_CAPABILITIES 0x200A +#define PI_ITEM_K_MAC_FRM_STAT_FUNC 0x200B +#define PI_ITEM_K_MAC_T_MAX_CAP 0x200D +#define PI_ITEM_K_MAC_TVX_CAP 0x200E + +#define PI_GRP_K_MAC_CONFIG 0x2014 +#define PI_ITEM_K_MAC_AVAIL_PATHS 0x2016 +#define PI_ITEM_K_MAC_CURRENT_PATH 0x2017 +#define PI_ITEM_K_MAC_UP_NBR 0x2018 +#define PI_ITEM_K_MAC_DOWN_NBR 0x2019 +#define PI_ITEM_K_MAC_OLD_UP_NBR 0x201A +#define PI_ITEM_K_MAC_OLD_DOWN_NBR 0x201B +#define PI_ITEM_K_MAC_DUP_ADDR_TEST 0x201D +#define PI_ITEM_K_MAC_REQ_PATHS 0x2020 +#define PI_ITEM_K_MAC_DOWN_PORT_TYPE 0x2021 +#define PI_ITEM_K_MAC_INDEX 0x2022 + +#define PI_GRP_K_MAC_ADDRESS 0x2028 +#define PI_ITEM_K_MAC_SMT_ADDRESS 0x2029 + +#define PI_GRP_K_MAC_OPERATION 0x2032 +#define PI_ITEM_K_MAC_TREQ 0x2033 +#define PI_ITEM_K_MAC_TNEG 0x2034 +#define PI_ITEM_K_MAC_TMAX 0x2035 +#define PI_ITEM_K_MAC_TVX_VALUE 0x2036 + +#define PI_GRP_K_MAC_COUNTERS 0x2046 +#define PI_ITEM_K_MAC_FRAME_CT 0x2047 +#define PI_ITEM_K_MAC_COPIED_CT 0x2048 +#define PI_ITEM_K_MAC_TRANSMIT_CT 0x2049 +#define PI_ITEM_K_MAC_ERROR_CT 0x2051 +#define PI_ITEM_K_MAC_LOST_CT 0x2052 + +#define PI_GRP_K_MAC_FRM_ERR_COND 0x205A +#define PI_ITEM_K_MAC_FRM_ERR_THR 0x205F +#define PI_ITEM_K_MAC_FRM_ERR_RAT 0x2060 + +#define PI_GRP_K_MAC_STATUS 0x206E +#define PI_ITEM_K_MAC_RMT_STATE 0x206F +#define PI_ITEM_K_MAC_DA_FLAG 0x2070 +#define PI_ITEM_K_MAC_UNDA_FLAG 0x2071 +#define PI_ITEM_K_MAC_FRM_ERR_FLAG 0x2072 +#define PI_ITEM_K_MAC_MA_UNIT_AVAIL 0x2074 +#define PI_ITEM_K_MAC_HW_PRESENT 0x2075 +#define PI_ITEM_K_MAC_MA_UNIT_ENAB 0x2076 + +#define PI_GRP_K_PATH_CONFIG 0x320A +#define PI_ITEM_K_PATH_INDEX 0x320B +#define PI_ITEM_K_PATH_CONFIGURATION 0x3212 +#define PI_ITEM_K_PATH_TVX_LB 0x3215 +#define PI_ITEM_K_PATH_T_MAX_LB 0x3216 +#define PI_ITEM_K_PATH_MAX_T_REQ 0x3217 + +#define PI_GRP_K_PORT_CONFIG 0x400A +#define PI_ITEM_K_PORT_MY_TYPE 0x400C +#define PI_ITEM_K_PORT_NBR_TYPE 0x400D +#define PI_ITEM_K_PORT_CONN_POLS 0x400E +#define PI_ITEM_K_PORT_MAC_INDICATED 0x400F +#define PI_ITEM_K_PORT_CURRENT_PATH 0x4010 +#define PI_ITEM_K_PORT_REQ_PATHS 0x4011 +#define PI_ITEM_K_PORT_MAC_PLACEMENT 0x4012 +#define PI_ITEM_K_PORT_AVAIL_PATHS 0x4013 +#define PI_ITEM_K_PORT_PMD_CLASS 0x4016 +#define PI_ITEM_K_PORT_CONN_CAPS 0x4017 +#define PI_ITEM_K_PORT_INDEX 0x401D + +#define PI_GRP_K_PORT_OPERATION 0x401E +#define PI_ITEM_K_PORT_BS_FLAG 0x4021 + +#define PI_GRP_K_PORT_ERR_CNTRS 0x4028 +#define PI_ITEM_K_PORT_LCT_FAIL_CT 0x402A + +#define PI_GRP_K_PORT_LER 0x4032 +#define PI_ITEM_K_PORT_LER_ESTIMATE 0x4033 +#define PI_ITEM_K_PORT_LEM_REJ_CT 0x4034 +#define PI_ITEM_K_PORT_LEM_CT 0x4035 +#define PI_ITEM_K_PORT_LER_CUTOFF 0x403A +#define PI_ITEM_K_PORT_LER_ALARM 0x403B + +#define PI_GRP_K_PORT_STATUS 0x403C +#define PI_ITEM_K_PORT_CONNECT_STATE 0x403D +#define PI_ITEM_K_PORT_PCM_STATE 0x403E +#define PI_ITEM_K_PORT_PC_WITHHOLD 0x403F +#define PI_ITEM_K_PORT_LER_FLAG 0x4040 +#define PI_ITEM_K_PORT_HW_PRESENT 0x4041 + +#define PI_ITEM_K_PORT_ACT 0x4046 + +/* Addr_Filter_Set Request */ + +#define PI_CMD_ADDR_FILTER_K_SIZE 62 + +typedef struct + { + PI_UINT32 cmd_type; + PI_LAN_ADDR entry[PI_CMD_ADDR_FILTER_K_SIZE]; + } PI_CMD_ADDR_FILTER_SET_REQ; + +/* Addr_Filter_Set Response */ + +typedef struct + { + PI_RSP_HEADER header; + } PI_CMD_ADDR_FILTER_SET_RSP; + +/* Addr_Filter_Get Request */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_ADDR_FILTER_GET_REQ; + +/* Addr_Filter_Get Response */ + +typedef struct + { + PI_RSP_HEADER header; + PI_LAN_ADDR entry[PI_CMD_ADDR_FILTER_K_SIZE]; + } PI_CMD_ADDR_FILTER_GET_RSP; + +/* Status_Chars_Get Request */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_STATUS_CHARS_GET_REQ; + +/* Status_Chars_Get Response */ + +typedef struct + { + PI_RSP_HEADER header; + PI_STATION_ID station_id; /* Station */ + PI_UINT32 station_type; + PI_UINT32 smt_ver_id; + PI_UINT32 smt_ver_id_max; + PI_UINT32 smt_ver_id_min; + PI_UINT32 station_state; + PI_LAN_ADDR link_addr; /* Link */ + PI_UINT32 t_req; + PI_UINT32 tvx; + PI_UINT32 token_timeout; + PI_UINT32 purger_enb; + PI_UINT32 link_state; + PI_UINT32 tneg; + PI_UINT32 dup_addr_flag; + PI_LAN_ADDR una; + PI_LAN_ADDR una_old; + PI_UINT32 un_dup_addr_flag; + PI_LAN_ADDR dna; + PI_LAN_ADDR dna_old; + PI_UINT32 purger_state; + PI_UINT32 fci_mode; + PI_UINT32 error_reason; + PI_UINT32 loopback; + PI_UINT32 ring_latency; + PI_LAN_ADDR last_dir_beacon_sa; + PI_LAN_ADDR last_dir_beacon_una; + PI_UINT32 phy_type[PI_PHY_K_MAX]; /* Phy */ + PI_UINT32 pmd_type[PI_PHY_K_MAX]; + PI_UINT32 lem_threshold[PI_PHY_K_MAX]; + PI_UINT32 phy_state[PI_PHY_K_MAX]; + PI_UINT32 nbor_phy_type[PI_PHY_K_MAX]; + PI_UINT32 link_error_est[PI_PHY_K_MAX]; + PI_UINT32 broken_reason[PI_PHY_K_MAX]; + PI_UINT32 reject_reason[PI_PHY_K_MAX]; + PI_UINT32 cntr_interval; /* Miscellaneous */ + PI_UINT32 module_rev; + PI_UINT32 firmware_rev; + PI_UINT32 mop_device_type; + PI_UINT32 phy_led[PI_PHY_K_MAX]; + PI_UINT32 flush_time; + } PI_CMD_STATUS_CHARS_GET_RSP; + +/* FDDI_MIB_Get Request */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_FDDI_MIB_GET_REQ; + +/* FDDI_MIB_Get Response */ + +typedef struct + { + PI_RSP_HEADER header; + + /* SMT GROUP */ + + PI_STATION_ID smt_station_id; + PI_UINT32 smt_op_version_id; + PI_UINT32 smt_hi_version_id; + PI_UINT32 smt_lo_version_id; + PI_UINT32 smt_mac_ct; + PI_UINT32 smt_non_master_ct; + PI_UINT32 smt_master_ct; + PI_UINT32 smt_paths_available; + PI_UINT32 smt_config_capabilities; + PI_UINT32 smt_config_policy; + PI_UINT32 smt_connection_policy; + PI_UINT32 smt_t_notify; + PI_UINT32 smt_status_reporting; + PI_UINT32 smt_ecm_state; + PI_UINT32 smt_cf_state; + PI_UINT32 smt_hold_state; + PI_UINT32 smt_remote_disconnect_flag; + PI_UINT32 smt_station_action; + + /* MAC GROUP */ + + PI_UINT32 mac_frame_status_capabilities; + PI_UINT32 mac_t_max_greatest_lower_bound; + PI_UINT32 mac_tvx_greatest_lower_bound; + PI_UINT32 mac_paths_available; + PI_UINT32 mac_current_path; + PI_LAN_ADDR mac_upstream_nbr; + PI_LAN_ADDR mac_old_upstream_nbr; + PI_UINT32 mac_dup_addr_test; + PI_UINT32 mac_paths_requested; + PI_UINT32 mac_downstream_port_type; + PI_LAN_ADDR mac_smt_address; + PI_UINT32 mac_t_req; + PI_UINT32 mac_t_neg; + PI_UINT32 mac_t_max; + PI_UINT32 mac_tvx_value; + PI_UINT32 mac_t_min; + PI_UINT32 mac_current_frame_status; + /* mac_frame_cts */ + /* mac_error_cts */ + /* mac_lost_cts */ + PI_UINT32 mac_frame_error_threshold; + PI_UINT32 mac_frame_error_ratio; + PI_UINT32 mac_rmt_state; + PI_UINT32 mac_da_flag; + PI_UINT32 mac_una_da_flag; + PI_UINT32 mac_frame_condition; + PI_UINT32 mac_chip_set; + PI_UINT32 mac_action; + + /* PATH GROUP => Does not need to be implemented */ + + /* PORT GROUP */ + + PI_UINT32 port_pc_type[PI_PHY_K_MAX]; + PI_UINT32 port_pc_neighbor[PI_PHY_K_MAX]; + PI_UINT32 port_connection_policies[PI_PHY_K_MAX]; + PI_UINT32 port_remote_mac_indicated[PI_PHY_K_MAX]; + PI_UINT32 port_ce_state[PI_PHY_K_MAX]; + PI_UINT32 port_paths_requested[PI_PHY_K_MAX]; + PI_UINT32 port_mac_placement[PI_PHY_K_MAX]; + PI_UINT32 port_available_paths[PI_PHY_K_MAX]; + PI_UINT32 port_mac_loop_time[PI_PHY_K_MAX]; + PI_UINT32 port_tb_max[PI_PHY_K_MAX]; + PI_UINT32 port_bs_flag[PI_PHY_K_MAX]; + /* port_lct_fail_cts[PI_PHY_K_MAX]; */ + PI_UINT32 port_ler_estimate[PI_PHY_K_MAX]; + /* port_lem_reject_cts[PI_PHY_K_MAX]; */ + /* port_lem_cts[PI_PHY_K_MAX]; */ + PI_UINT32 port_ler_cutoff[PI_PHY_K_MAX]; + PI_UINT32 port_ler_alarm[PI_PHY_K_MAX]; + PI_UINT32 port_connect_state[PI_PHY_K_MAX]; + PI_UINT32 port_pcm_state[PI_PHY_K_MAX]; + PI_UINT32 port_pc_withhold[PI_PHY_K_MAX]; + PI_UINT32 port_ler_condition[PI_PHY_K_MAX]; + PI_UINT32 port_chip_set[PI_PHY_K_MAX]; + PI_UINT32 port_action[PI_PHY_K_MAX]; + + /* ATTACHMENT GROUP */ + + PI_UINT32 attachment_class; + PI_UINT32 attachment_ob_present; + PI_UINT32 attachment_imax_expiration; + PI_UINT32 attachment_inserted_status; + PI_UINT32 attachment_insert_policy; + + /* CHIP SET GROUP => Does not need to be implemented */ + + } PI_CMD_FDDI_MIB_GET_RSP; + +/* DEC_Ext_MIB_Get Request */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_DEC_EXT_MIB_GET_REQ; + +/* DEC_Ext_MIB_Get (efddi and efdx groups only) Response */ + +typedef struct + { + PI_RSP_HEADER header; + + /* SMT GROUP */ + + PI_UINT32 esmt_station_type; + + /* MAC GROUP */ + + PI_UINT32 emac_link_state; + PI_UINT32 emac_ring_purger_state; + PI_UINT32 emac_ring_purger_enable; + PI_UINT32 emac_frame_strip_mode; + PI_UINT32 emac_ring_error_reason; + PI_UINT32 emac_up_nbr_dup_addr_flag; + PI_UINT32 emac_restricted_token_timeout; + + /* PORT GROUP */ + + PI_UINT32 eport_pmd_type[PI_PHY_K_MAX]; + PI_UINT32 eport_phy_state[PI_PHY_K_MAX]; + PI_UINT32 eport_reject_reason[PI_PHY_K_MAX]; + + /* FDX (Full-Duplex) GROUP */ + + PI_UINT32 efdx_enable; /* Valid only in SMT 7.3 */ + PI_UINT32 efdx_op; /* Valid only in SMT 7.3 */ + PI_UINT32 efdx_state; /* Valid only in SMT 7.3 */ + + } PI_CMD_DEC_EXT_MIB_GET_RSP; + +typedef struct + { + PI_CNTR traces_rcvd; /* Station */ + PI_CNTR frame_cnt; /* Link */ + PI_CNTR error_cnt; + PI_CNTR lost_cnt; + PI_CNTR octets_rcvd; + PI_CNTR octets_sent; + PI_CNTR pdus_rcvd; + PI_CNTR pdus_sent; + PI_CNTR mcast_octets_rcvd; + PI_CNTR mcast_octets_sent; + PI_CNTR mcast_pdus_rcvd; + PI_CNTR mcast_pdus_sent; + PI_CNTR xmt_underruns; + PI_CNTR xmt_failures; + PI_CNTR block_check_errors; + PI_CNTR frame_status_errors; + PI_CNTR pdu_length_errors; + PI_CNTR rcv_overruns; + PI_CNTR user_buff_unavailable; + PI_CNTR inits_initiated; + PI_CNTR inits_rcvd; + PI_CNTR beacons_initiated; + PI_CNTR dup_addrs; + PI_CNTR dup_tokens; + PI_CNTR purge_errors; + PI_CNTR fci_strip_errors; + PI_CNTR traces_initiated; + PI_CNTR directed_beacons_rcvd; + PI_CNTR emac_frame_alignment_errors; + PI_CNTR ebuff_errors[PI_PHY_K_MAX]; /* Phy */ + PI_CNTR lct_rejects[PI_PHY_K_MAX]; + PI_CNTR lem_rejects[PI_PHY_K_MAX]; + PI_CNTR link_errors[PI_PHY_K_MAX]; + PI_CNTR connections[PI_PHY_K_MAX]; + PI_CNTR copied_cnt; /* Valid only if using SMT 7.3 */ + PI_CNTR transmit_cnt; /* Valid only if using SMT 7.3 */ + PI_CNTR tokens; + } PI_CNTR_BLK; + +/* Counters_Get Request */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_CNTRS_GET_REQ; + +/* Counters_Get Response */ + +typedef struct + { + PI_RSP_HEADER header; + PI_CNTR time_since_reset; + PI_CNTR_BLK cntrs; + } PI_CMD_CNTRS_GET_RSP; + +/* Counters_Set Request */ + +typedef struct + { + PI_UINT32 cmd_type; + PI_CNTR_BLK cntrs; + } PI_CMD_CNTRS_SET_REQ; + +/* Counters_Set Response */ + +typedef struct + { + PI_RSP_HEADER header; + } PI_CMD_CNTRS_SET_RSP; + +/* Error_Log_Clear Request */ + +typedef struct + { + PI_UINT32 cmd_type; + } PI_CMD_ERROR_LOG_CLEAR_REQ; + +/* Error_Log_Clear Response */ + +typedef struct + { + PI_RSP_HEADER header; + } PI_CMD_ERROR_LOG_CLEAR_RSP; + +/* Error_Log_Get Request */ + +#define PI_LOG_ENTRY_K_INDEX_MIN 0 /* Minimum index for entry */ + +typedef struct + { + PI_UINT32 cmd_type; + PI_UINT32 entry_index; + } PI_CMD_ERROR_LOG_GET_REQ; + +/* Error_Log_Get Response */ + +#define PI_K_LOG_FW_SIZE 111 /* Max number of fw longwords */ +#define PI_K_LOG_DIAG_SIZE 6 /* Max number of diag longwords */ + +typedef struct + { + struct + { + PI_UINT32 fru_imp_mask; + PI_UINT32 test_id; + PI_UINT32 reserved[PI_K_LOG_DIAG_SIZE]; + } diag; + PI_UINT32 fw[PI_K_LOG_FW_SIZE]; + } PI_LOG_ENTRY; + +typedef struct + { + PI_RSP_HEADER header; + PI_UINT32 event_status; + PI_UINT32 caller_id; + PI_UINT32 timestamp_l; + PI_UINT32 timestamp_h; + PI_UINT32 write_count; + PI_LOG_ENTRY entry_info; + } PI_CMD_ERROR_LOG_GET_RSP; + +/* Define error log related constants and types. */ +/* Not all of the caller id's can occur. The only ones currently */ +/* implemented are: none, selftest, mfg, fw, console */ + +#define PI_LOG_EVENT_STATUS_K_VALID 0 /* Valid Event Status */ +#define PI_LOG_EVENT_STATUS_K_INVALID 1 /* Invalid Event Status */ +#define PI_LOG_CALLER_ID_K_NONE 0 /* No caller */ +#define PI_LOG_CALLER_ID_K_SELFTEST 1 /* Normal power-up selftest */ +#define PI_LOG_CALLER_ID_K_MFG 2 /* Mfg power-up selftest */ +#define PI_LOG_CALLER_ID_K_ONLINE 3 /* On-line diagnostics */ +#define PI_LOG_CALLER_ID_K_HW 4 /* Hardware */ +#define PI_LOG_CALLER_ID_K_FW 5 /* Firmware */ +#define PI_LOG_CALLER_ID_K_CNS_HW 6 /* CNS firmware */ +#define PI_LOG_CALLER_ID_K_CNS_FW 7 /* CNS hardware */ +#define PI_LOG_CALLER_ID_K_CONSOLE 8 /* Console Caller Id */ + +/* + * Place all DMA commands in the following request and response structures + * to simplify code. + */ + +typedef union + { + PI_UINT32 cmd_type; + PI_CMD_START_REQ start; + PI_CMD_FILTERS_SET_REQ filter_set; + PI_CMD_FILTERS_GET_REQ filter_get; + PI_CMD_CHARS_SET_REQ char_set; + PI_CMD_ADDR_FILTER_SET_REQ addr_filter_set; + PI_CMD_ADDR_FILTER_GET_REQ addr_filter_get; + PI_CMD_STATUS_CHARS_GET_REQ stat_char_get; + PI_CMD_CNTRS_GET_REQ cntrs_get; + PI_CMD_CNTRS_SET_REQ cntrs_set; + PI_CMD_ERROR_LOG_CLEAR_REQ error_log_clear; + PI_CMD_ERROR_LOG_GET_REQ error_log_read; + PI_CMD_SNMP_SET_REQ snmp_set; + PI_CMD_FDDI_MIB_GET_REQ fddi_mib_get; + PI_CMD_DEC_EXT_MIB_GET_REQ dec_mib_get; + PI_CMD_SMT_MIB_SET_REQ smt_mib_set; + PI_CMD_SMT_MIB_GET_REQ smt_mib_get; + char pad[PI_CMD_REQ_K_SIZE_MAX]; + } PI_DMA_CMD_REQ; + +typedef union + { + PI_RSP_HEADER header; + PI_CMD_START_RSP start; + PI_CMD_FILTERS_SET_RSP filter_set; + PI_CMD_FILTERS_GET_RSP filter_get; + PI_CMD_CHARS_SET_RSP char_set; + PI_CMD_ADDR_FILTER_SET_RSP addr_filter_set; + PI_CMD_ADDR_FILTER_GET_RSP addr_filter_get; + PI_CMD_STATUS_CHARS_GET_RSP stat_char_get; + PI_CMD_CNTRS_GET_RSP cntrs_get; + PI_CMD_CNTRS_SET_RSP cntrs_set; + PI_CMD_ERROR_LOG_CLEAR_RSP error_log_clear; + PI_CMD_ERROR_LOG_GET_RSP error_log_get; + PI_CMD_SNMP_SET_RSP snmp_set; + PI_CMD_FDDI_MIB_GET_RSP fddi_mib_get; + PI_CMD_DEC_EXT_MIB_GET_RSP dec_mib_get; + PI_CMD_SMT_MIB_SET_RSP smt_mib_set; + PI_CMD_SMT_MIB_GET_RSP smt_mib_get; + char pad[PI_CMD_RSP_K_SIZE_MAX]; + } PI_DMA_CMD_RSP; + +typedef union + { + PI_DMA_CMD_REQ request; + PI_DMA_CMD_RSP response; + } PI_DMA_CMD_BUFFER; + + +/* Define format of Consumer Block (resident in host memory) */ + +typedef struct + { + volatile PI_UINT32 xmt_rcv_data; + volatile PI_UINT32 reserved_1; + volatile PI_UINT32 smt_host; + volatile PI_UINT32 reserved_2; + volatile PI_UINT32 unsol; + volatile PI_UINT32 reserved_3; + volatile PI_UINT32 cmd_rsp; + volatile PI_UINT32 reserved_4; + volatile PI_UINT32 cmd_req; + volatile PI_UINT32 reserved_5; + } PI_CONSUMER_BLOCK; + +#define PI_CONS_M_RCV_INDEX 0x000000FF +#define PI_CONS_M_XMT_INDEX 0x00FF0000 +#define PI_CONS_V_RCV_INDEX 0 +#define PI_CONS_V_XMT_INDEX 16 + +/* Offsets into consumer block */ + +#define PI_CONS_BLK_K_XMT_RCV 0x00 +#define PI_CONS_BLK_K_SMT_HOST 0x08 +#define PI_CONS_BLK_K_UNSOL 0x10 +#define PI_CONS_BLK_K_CMD_RSP 0x18 +#define PI_CONS_BLK_K_CMD_REQ 0x20 + +/* Offsets into descriptor block */ + +#define PI_DESCR_BLK_K_RCV_DATA 0x0000 +#define PI_DESCR_BLK_K_XMT_DATA 0x0800 +#define PI_DESCR_BLK_K_SMT_HOST 0x1000 +#define PI_DESCR_BLK_K_UNSOL 0x1200 +#define PI_DESCR_BLK_K_CMD_RSP 0x1280 +#define PI_DESCR_BLK_K_CMD_REQ 0x1300 + +/* Define format of a rcv descr (Rcv Data, Cmd Rsp, Unsolicited, SMT Host) */ +/* Note a field has been added for later versions of the PDQ to allow for */ +/* finer granularity of the rcv buffer alignment. For backwards */ +/* compatibility, the two bits (which allow the rcv buffer to be longword */ +/* aligned) have been added at the MBZ bits. To support previous drivers, */ +/* the MBZ definition is left intact. */ + +typedef struct + { + PI_UINT32 long_0; + PI_UINT32 long_1; + } PI_RCV_DESCR; + +#define PI_RCV_DESCR_M_SOP 0x80000000 +#define PI_RCV_DESCR_M_SEG_LEN_LO 0x60000000 +#define PI_RCV_DESCR_M_MBZ 0x60000000 +#define PI_RCV_DESCR_M_SEG_LEN 0x1F800000 +#define PI_RCV_DESCR_M_SEG_LEN_HI 0x1FF00000 +#define PI_RCV_DESCR_M_SEG_CNT 0x000F0000 +#define PI_RCV_DESCR_M_BUFF_HI 0x0000FFFF + +#define PI_RCV_DESCR_V_SOP 31 +#define PI_RCV_DESCR_V_SEG_LEN_LO 29 +#define PI_RCV_DESCR_V_MBZ 29 +#define PI_RCV_DESCR_V_SEG_LEN 23 +#define PI_RCV_DESCR_V_SEG_LEN_HI 20 +#define PI_RCV_DESCR_V_SEG_CNT 16 +#define PI_RCV_DESCR_V_BUFF_HI 0 + +/* Define the format of a transmit descriptor (Xmt Data, Cmd Req) */ + +typedef struct + { + PI_UINT32 long_0; + PI_UINT32 long_1; + } PI_XMT_DESCR; + +#define PI_XMT_DESCR_M_SOP 0x80000000 +#define PI_XMT_DESCR_M_EOP 0x40000000 +#define PI_XMT_DESCR_M_MBZ 0x20000000 +#define PI_XMT_DESCR_M_SEG_LEN 0x1FFF0000 +#define PI_XMT_DESCR_M_BUFF_HI 0x0000FFFF + +#define PI_XMT_DESCR_V_SOP 31 +#define PI_XMT_DESCR_V_EOP 30 +#define PI_XMT_DESCR_V_MBZ 29 +#define PI_XMT_DESCR_V_SEG_LEN 16 +#define PI_XMT_DESCR_V_BUFF_HI 0 + +/* Define format of the Descriptor Block (resident in host memory) */ + +#define PI_RCV_DATA_K_NUM_ENTRIES 256 +#define PI_XMT_DATA_K_NUM_ENTRIES 256 +#define PI_SMT_HOST_K_NUM_ENTRIES 64 +#define PI_UNSOL_K_NUM_ENTRIES 16 +#define PI_CMD_RSP_K_NUM_ENTRIES 16 +#define PI_CMD_REQ_K_NUM_ENTRIES 16 + +typedef struct + { + PI_RCV_DESCR rcv_data[PI_RCV_DATA_K_NUM_ENTRIES]; + PI_XMT_DESCR xmt_data[PI_XMT_DATA_K_NUM_ENTRIES]; + PI_RCV_DESCR smt_host[PI_SMT_HOST_K_NUM_ENTRIES]; + PI_RCV_DESCR unsol[PI_UNSOL_K_NUM_ENTRIES]; + PI_RCV_DESCR cmd_rsp[PI_CMD_RSP_K_NUM_ENTRIES]; + PI_XMT_DESCR cmd_req[PI_CMD_REQ_K_NUM_ENTRIES]; + } PI_DESCR_BLOCK; + +/* Define Port Registers - offsets from PDQ Base address */ + +#define PI_PDQ_K_REG_PORT_RESET 0x00000000 +#define PI_PDQ_K_REG_HOST_DATA 0x00000004 +#define PI_PDQ_K_REG_PORT_CTRL 0x00000008 +#define PI_PDQ_K_REG_PORT_DATA_A 0x0000000C +#define PI_PDQ_K_REG_PORT_DATA_B 0x00000010 +#define PI_PDQ_K_REG_PORT_STATUS 0x00000014 +#define PI_PDQ_K_REG_TYPE_0_STATUS 0x00000018 +#define PI_PDQ_K_REG_HOST_INT_ENB 0x0000001C +#define PI_PDQ_K_REG_TYPE_2_PROD_NOINT 0x00000020 +#define PI_PDQ_K_REG_TYPE_2_PROD 0x00000024 +#define PI_PDQ_K_REG_CMD_RSP_PROD 0x00000028 +#define PI_PDQ_K_REG_CMD_REQ_PROD 0x0000002C +#define PI_PDQ_K_REG_SMT_HOST_PROD 0x00000030 +#define PI_PDQ_K_REG_UNSOL_PROD 0x00000034 + +/* Port Control Register - Command codes for primary commands */ + +#define PI_PCTRL_M_CMD_ERROR 0x8000 +#define PI_PCTRL_M_BLAST_FLASH 0x4000 +#define PI_PCTRL_M_HALT 0x2000 +#define PI_PCTRL_M_COPY_DATA 0x1000 +#define PI_PCTRL_M_ERROR_LOG_START 0x0800 +#define PI_PCTRL_M_ERROR_LOG_READ 0x0400 +#define PI_PCTRL_M_XMT_DATA_FLUSH_DONE 0x0200 +#define PI_PCTRL_M_INIT 0x0100 +#define PI_PCTRL_M_INIT_START 0x0080 +#define PI_PCTRL_M_CONS_BLOCK 0x0040 +#define PI_PCTRL_M_UNINIT 0x0020 +#define PI_PCTRL_M_RING_MEMBER 0x0010 +#define PI_PCTRL_M_MLA 0x0008 +#define PI_PCTRL_M_FW_REV_READ 0x0004 +#define PI_PCTRL_M_DEV_SPECIFIC 0x0002 +#define PI_PCTRL_M_SUB_CMD 0x0001 + +/* Define sub-commands accessed via the PI_PCTRL_M_SUB_CMD command */ + +#define PI_SUB_CMD_K_LINK_UNINIT 0x0001 +#define PI_SUB_CMD_K_BURST_SIZE_SET 0x0002 +#define PI_SUB_CMD_K_PDQ_REV_GET 0x0004 +#define PI_SUB_CMD_K_HW_REV_GET 0x0008 + +/* Define some Port Data B values */ + +#define PI_PDATA_B_DMA_BURST_SIZE_4 0 /* valid values for command */ +#define PI_PDATA_B_DMA_BURST_SIZE_8 1 +#define PI_PDATA_B_DMA_BURST_SIZE_16 2 +#define PI_PDATA_B_DMA_BURST_SIZE_32 3 /* not supported on PCI */ +#define PI_PDATA_B_DMA_BURST_SIZE_DEF PI_PDATA_B_DMA_BURST_SIZE_16 + +/* Port Data A Reset state */ + +#define PI_PDATA_A_RESET_M_UPGRADE 0x00000001 +#define PI_PDATA_A_RESET_M_SOFT_RESET 0x00000002 +#define PI_PDATA_A_RESET_M_SKIP_ST 0x00000004 + +/* Read adapter MLA address port control command constants */ + +#define PI_PDATA_A_MLA_K_LO 0 +#define PI_PDATA_A_MLA_K_HI 1 + +/* Byte Swap values for init command */ + +#define PI_PDATA_A_INIT_M_DESC_BLK_ADDR 0x0FFFFE000 +#define PI_PDATA_A_INIT_M_RESERVED 0x000001FFC +#define PI_PDATA_A_INIT_M_BSWAP_DATA 0x000000002 +#define PI_PDATA_A_INIT_M_BSWAP_LITERAL 0x000000001 + +#define PI_PDATA_A_INIT_V_DESC_BLK_ADDR 13 +#define PI_PDATA_A_INIT_V_RESERVED 3 +#define PI_PDATA_A_INIT_V_BSWAP_DATA 1 +#define PI_PDATA_A_INIT_V_BSWAP_LITERAL 0 + +/* Port Reset Register */ + +#define PI_RESET_M_ASSERT_RESET 1 + +/* Port Status register */ + +#define PI_PSTATUS_V_RCV_DATA_PENDING 31 +#define PI_PSTATUS_V_XMT_DATA_PENDING 30 +#define PI_PSTATUS_V_SMT_HOST_PENDING 29 +#define PI_PSTATUS_V_UNSOL_PENDING 28 +#define PI_PSTATUS_V_CMD_RSP_PENDING 27 +#define PI_PSTATUS_V_CMD_REQ_PENDING 26 +#define PI_PSTATUS_V_TYPE_0_PENDING 25 +#define PI_PSTATUS_V_RESERVED_1 16 +#define PI_PSTATUS_V_RESERVED_2 11 +#define PI_PSTATUS_V_STATE 8 +#define PI_PSTATUS_V_HALT_ID 0 + +#define PI_PSTATUS_M_RCV_DATA_PENDING 0x80000000 +#define PI_PSTATUS_M_XMT_DATA_PENDING 0x40000000 +#define PI_PSTATUS_M_SMT_HOST_PENDING 0x20000000 +#define PI_PSTATUS_M_UNSOL_PENDING 0x10000000 +#define PI_PSTATUS_M_CMD_RSP_PENDING 0x08000000 +#define PI_PSTATUS_M_CMD_REQ_PENDING 0x04000000 +#define PI_PSTATUS_M_TYPE_0_PENDING 0x02000000 +#define PI_PSTATUS_M_RESERVED_1 0x01FF0000 +#define PI_PSTATUS_M_RESERVED_2 0x0000F800 +#define PI_PSTATUS_M_STATE 0x00000700 +#define PI_PSTATUS_M_HALT_ID 0x000000FF + +/* Define Halt Id's */ +/* Do not insert into this list, only append. */ + +#define PI_HALT_ID_K_SELFTEST_TIMEOUT 0 +#define PI_HALT_ID_K_PARITY_ERROR 1 +#define PI_HALT_ID_K_HOST_DIR_HALT 2 +#define PI_HALT_ID_K_SW_FAULT 3 +#define PI_HALT_ID_K_HW_FAULT 4 +#define PI_HALT_ID_K_PC_TRACE 5 +#define PI_HALT_ID_K_DMA_ERROR 6 /* Host Data has error reg */ +#define PI_HALT_ID_K_IMAGE_CRC_ERROR 7 /* Image is bad, update it */ +#define PI_HALT_ID_K_BUS_EXCEPTION 8 /* 68K bus exception */ + +/* Host Interrupt Enable Register as seen by host */ + +#define PI_HOST_INT_M_XMT_DATA_ENB 0x80000000 /* Type 2 Enables */ +#define PI_HOST_INT_M_RCV_DATA_ENB 0x40000000 +#define PI_HOST_INT_M_SMT_HOST_ENB 0x10000000 /* Type 1 Enables */ +#define PI_HOST_INT_M_UNSOL_ENB 0x20000000 +#define PI_HOST_INT_M_CMD_RSP_ENB 0x08000000 +#define PI_HOST_INT_M_CMD_REQ_ENB 0x04000000 +#define PI_HOST_INT_M_TYPE_1_RESERVED 0x00FF0000 +#define PI_HOST_INT_M_TYPE_0_RESERVED 0x0000FF00 /* Type 0 Enables */ +#define PI_HOST_INT_M_1MS 0x00000080 +#define PI_HOST_INT_M_20MS 0x00000040 +#define PI_HOST_INT_M_CSR_CMD_DONE 0x00000020 +#define PI_HOST_INT_M_STATE_CHANGE 0x00000010 +#define PI_HOST_INT_M_XMT_FLUSH 0x00000008 +#define PI_HOST_INT_M_NXM 0x00000004 +#define PI_HOST_INT_M_PM_PAR_ERR 0x00000002 +#define PI_HOST_INT_M_BUS_PAR_ERR 0x00000001 + +#define PI_HOST_INT_V_XMT_DATA_ENB 31 /* Type 2 Enables */ +#define PI_HOST_INT_V_RCV_DATA_ENB 30 +#define PI_HOST_INT_V_SMT_HOST_ENB 29 /* Type 1 Enables */ +#define PI_HOST_INT_V_UNSOL_ENB 28 +#define PI_HOST_INT_V_CMD_RSP_ENB 27 +#define PI_HOST_INT_V_CMD_REQ_ENB 26 +#define PI_HOST_INT_V_TYPE_1_RESERVED 16 +#define PI_HOST_INT_V_TYPE_0_RESERVED 8 /* Type 0 Enables */ +#define PI_HOST_INT_V_1MS_ENB 7 +#define PI_HOST_INT_V_20MS_ENB 6 +#define PI_HOST_INT_V_CSR_CMD_DONE_ENB 5 +#define PI_HOST_INT_V_STATE_CHANGE_ENB 4 +#define PI_HOST_INT_V_XMT_FLUSH_ENB 3 +#define PI_HOST_INT_V_NXM_ENB 2 +#define PI_HOST_INT_V_PM_PAR_ERR_ENB 1 +#define PI_HOST_INT_V_BUS_PAR_ERR_ENB 0 + +#define PI_HOST_INT_K_ACK_ALL_TYPE_0 0x000000FF +#define PI_HOST_INT_K_DISABLE_ALL_INTS 0x00000000 +#define PI_HOST_INT_K_ENABLE_ALL_INTS 0xFFFFFFFF +#define PI_HOST_INT_K_ENABLE_DEF_INTS 0xC000001F + +/* Type 0 Interrupt Status Register */ + +#define PI_TYPE_0_STAT_M_1MS 0x00000080 +#define PI_TYPE_0_STAT_M_20MS 0x00000040 +#define PI_TYPE_0_STAT_M_CSR_CMD_DONE 0x00000020 +#define PI_TYPE_0_STAT_M_STATE_CHANGE 0x00000010 +#define PI_TYPE_0_STAT_M_XMT_FLUSH 0x00000008 +#define PI_TYPE_0_STAT_M_NXM 0x00000004 +#define PI_TYPE_0_STAT_M_PM_PAR_ERR 0x00000002 +#define PI_TYPE_0_STAT_M_BUS_PAR_ERR 0x00000001 + +#define PI_TYPE_0_STAT_V_1MS 7 +#define PI_TYPE_0_STAT_V_20MS 6 +#define PI_TYPE_0_STAT_V_CSR_CMD_DONE 5 +#define PI_TYPE_0_STAT_V_STATE_CHANGE 4 +#define PI_TYPE_0_STAT_V_XMT_FLUSH 3 +#define PI_TYPE_0_STAT_V_NXM 2 +#define PI_TYPE_0_STAT_V_PM_PAR_ERR 1 +#define PI_TYPE_0_STAT_V_BUS_PAR_ERR 0 + +/* Register definition structures are defined for both big and little endian systems */ + +#ifndef __BIG_ENDIAN + +/* Little endian format of Type 1 Producer register */ + +typedef union + { + PI_UINT32 lword; + struct + { + PI_UINT8 prod; + PI_UINT8 comp; + PI_UINT8 mbz_1; + PI_UINT8 mbz_2; + } index; + } PI_TYPE_1_PROD_REG; + +/* Little endian format of Type 2 Producer register */ + +typedef union + { + PI_UINT32 lword; + struct + { + PI_UINT8 rcv_prod; + PI_UINT8 xmt_prod; + PI_UINT8 rcv_comp; + PI_UINT8 xmt_comp; + } index; + } PI_TYPE_2_PROD_REG; + +/* Little endian format of Type 1 Consumer Block longword */ + +typedef union + { + PI_UINT32 lword; + struct + { + PI_UINT8 cons; + PI_UINT8 res0; + PI_UINT8 res1; + PI_UINT8 res2; + } index; + } PI_TYPE_1_CONSUMER; + +/* Little endian format of Type 2 Consumer Block longword */ + +typedef union + { + PI_UINT32 lword; + struct + { + PI_UINT8 rcv_cons; + PI_UINT8 res0; + PI_UINT8 xmt_cons; + PI_UINT8 res1; + } index; + } PI_TYPE_2_CONSUMER; + +/* Define swapping required by DMA transfers. */ +#define PI_PDATA_A_INIT_M_BSWAP_INIT \ + (PI_PDATA_A_INIT_M_BSWAP_DATA) + +#else /* __BIG_ENDIAN */ + +/* Big endian format of Type 1 Producer register */ + +typedef union + { + PI_UINT32 lword; + struct + { + PI_UINT8 mbz_2; + PI_UINT8 mbz_1; + PI_UINT8 comp; + PI_UINT8 prod; + } index; + } PI_TYPE_1_PROD_REG; + +/* Big endian format of Type 2 Producer register */ + +typedef union + { + PI_UINT32 lword; + struct + { + PI_UINT8 xmt_comp; + PI_UINT8 rcv_comp; + PI_UINT8 xmt_prod; + PI_UINT8 rcv_prod; + } index; + } PI_TYPE_2_PROD_REG; + +/* Big endian format of Type 1 Consumer Block longword */ + +typedef union + { + PI_UINT32 lword; + struct + { + PI_UINT8 res2; + PI_UINT8 res1; + PI_UINT8 res0; + PI_UINT8 cons; + } index; + } PI_TYPE_1_CONSUMER; + +/* Big endian format of Type 2 Consumer Block longword */ + +typedef union + { + PI_UINT32 lword; + struct + { + PI_UINT8 res1; + PI_UINT8 xmt_cons; + PI_UINT8 res0; + PI_UINT8 rcv_cons; + } index; + } PI_TYPE_2_CONSUMER; + +/* Define swapping required by DMA transfers. */ +#define PI_PDATA_A_INIT_M_BSWAP_INIT \ + (PI_PDATA_A_INIT_M_BSWAP_DATA | PI_PDATA_A_INIT_M_BSWAP_LITERAL) + +#endif /* __BIG_ENDIAN */ + +/* Define TC PDQ CSR offset and length */ + +#define PI_TC_K_CSR_OFFSET 0x100000 +#define PI_TC_K_CSR_LEN 0x40 /* 64 bytes */ + +/* Define EISA controller register offsets */ + +#define PI_ESIC_K_CSR_IO_LEN 0x40 /* 64 bytes */ +#define PI_ESIC_K_BURST_HOLDOFF_LEN 0x04 /* 4 bytes */ +#define PI_ESIC_K_ESIC_CSR_LEN 0x40 /* 64 bytes */ + +#define PI_DEFEA_K_CSR_IO 0x000 +#define PI_DEFEA_K_BURST_HOLDOFF 0x040 +#define PI_ESIC_K_ESIC_CSR 0xC80 + +#define PI_ESIC_K_SLOT_ID 0xC80 +#define PI_ESIC_K_SLOT_CNTRL 0xC84 +#define PI_ESIC_K_MEM_ADD_CMP_0 0xC85 +#define PI_ESIC_K_MEM_ADD_CMP_1 0xC86 +#define PI_ESIC_K_MEM_ADD_CMP_2 0xC87 +#define PI_ESIC_K_MEM_ADD_HI_CMP_0 0xC88 +#define PI_ESIC_K_MEM_ADD_HI_CMP_1 0xC89 +#define PI_ESIC_K_MEM_ADD_HI_CMP_2 0xC8A +#define PI_ESIC_K_MEM_ADD_MASK_0 0xC8B +#define PI_ESIC_K_MEM_ADD_MASK_1 0xC8C +#define PI_ESIC_K_MEM_ADD_MASK_2 0xC8D +#define PI_ESIC_K_MEM_ADD_LO_CMP_0 0xC8E +#define PI_ESIC_K_MEM_ADD_LO_CMP_1 0xC8F +#define PI_ESIC_K_MEM_ADD_LO_CMP_2 0xC90 +#define PI_ESIC_K_IO_ADD_CMP_0_0 0xC91 +#define PI_ESIC_K_IO_ADD_CMP_0_1 0xC92 +#define PI_ESIC_K_IO_ADD_CMP_1_0 0xC93 +#define PI_ESIC_K_IO_ADD_CMP_1_1 0xC94 +#define PI_ESIC_K_IO_ADD_CMP_2_0 0xC95 +#define PI_ESIC_K_IO_ADD_CMP_2_1 0xC96 +#define PI_ESIC_K_IO_ADD_CMP_3_0 0xC97 +#define PI_ESIC_K_IO_ADD_CMP_3_1 0xC98 +#define PI_ESIC_K_IO_ADD_MASK_0_0 0xC99 +#define PI_ESIC_K_IO_ADD_MASK_0_1 0xC9A +#define PI_ESIC_K_IO_ADD_MASK_1_0 0xC9B +#define PI_ESIC_K_IO_ADD_MASK_1_1 0xC9C +#define PI_ESIC_K_IO_ADD_MASK_2_0 0xC9D +#define PI_ESIC_K_IO_ADD_MASK_2_1 0xC9E +#define PI_ESIC_K_IO_ADD_MASK_3_0 0xC9F +#define PI_ESIC_K_IO_ADD_MASK_3_1 0xCA0 +#define PI_ESIC_K_MOD_CONFIG_1 0xCA1 +#define PI_ESIC_K_MOD_CONFIG_2 0xCA2 +#define PI_ESIC_K_MOD_CONFIG_3 0xCA3 +#define PI_ESIC_K_MOD_CONFIG_4 0xCA4 +#define PI_ESIC_K_MOD_CONFIG_5 0xCA5 +#define PI_ESIC_K_MOD_CONFIG_6 0xCA6 +#define PI_ESIC_K_MOD_CONFIG_7 0xCA7 +#define PI_ESIC_K_DIP_SWITCH 0xCA8 +#define PI_ESIC_K_IO_CONFIG_STAT_0 0xCA9 +#define PI_ESIC_K_IO_CONFIG_STAT_1 0xCAA +#define PI_ESIC_K_DMA_CONFIG 0xCAB +#define PI_ESIC_K_INPUT_PORT 0xCAC +#define PI_ESIC_K_OUTPUT_PORT 0xCAD +#define PI_ESIC_K_FUNCTION_CNTRL 0xCAE + +/* Define the bits in the function control register. */ + +#define PI_FUNCTION_CNTRL_M_IOCS0 0x01 +#define PI_FUNCTION_CNTRL_M_IOCS1 0x02 +#define PI_FUNCTION_CNTRL_M_IOCS2 0x04 +#define PI_FUNCTION_CNTRL_M_IOCS3 0x08 +#define PI_FUNCTION_CNTRL_M_MEMCS0 0x10 +#define PI_FUNCTION_CNTRL_M_MEMCS1 0x20 +#define PI_FUNCTION_CNTRL_M_DMA 0x80 + +/* Define the bits in the slot control register. */ + +#define PI_SLOT_CNTRL_M_RESET 0x04 /* Don't use. */ +#define PI_SLOT_CNTRL_M_ERROR 0x02 /* Not implemented. */ +#define PI_SLOT_CNTRL_M_ENB 0x01 /* Must be set. */ + +/* Define the bits in the burst holdoff register. */ + +#define PI_BURST_HOLDOFF_M_HOLDOFF 0xFC +#define PI_BURST_HOLDOFF_M_RESERVED 0x02 +#define PI_BURST_HOLDOFF_M_MEM_MAP 0x01 + +#define PI_BURST_HOLDOFF_V_HOLDOFF 2 +#define PI_BURST_HOLDOFF_V_RESERVED 1 +#define PI_BURST_HOLDOFF_V_MEM_MAP 0 + +/* Define the implicit mask of the Memory Address Compare registers. */ + +#define PI_MEM_ADD_MASK_M 0x3ff + +/* Define the fields in the I/O Address Compare and Mask registers. */ + +#define PI_IO_CMP_M_SLOT 0xf0 + +#define PI_IO_CMP_V_SLOT 4 + +/* Define the fields in the Interrupt Channel Configuration and Status reg */ + +#define PI_CONFIG_STAT_0_M_PEND 0x80 +#define PI_CONFIG_STAT_0_M_RES_1 0x40 +#define PI_CONFIG_STAT_0_M_IREQ_OUT 0x20 +#define PI_CONFIG_STAT_0_M_IREQ_IN 0x10 +#define PI_CONFIG_STAT_0_M_INT_ENB 0x08 +#define PI_CONFIG_STAT_0_M_RES_0 0x04 +#define PI_CONFIG_STAT_0_M_IRQ 0x03 + +#define PI_CONFIG_STAT_0_V_PEND 7 +#define PI_CONFIG_STAT_0_V_RES_1 6 +#define PI_CONFIG_STAT_0_V_IREQ_OUT 5 +#define PI_CONFIG_STAT_0_V_IREQ_IN 4 +#define PI_CONFIG_STAT_0_V_INT_ENB 3 +#define PI_CONFIG_STAT_0_V_RES_0 2 +#define PI_CONFIG_STAT_0_V_IRQ 0 + +#define PI_CONFIG_STAT_0_IRQ_K_9 0 +#define PI_CONFIG_STAT_0_IRQ_K_10 1 +#define PI_CONFIG_STAT_0_IRQ_K_11 2 +#define PI_CONFIG_STAT_0_IRQ_K_15 3 + +/* Define DEC FDDIcontroller/EISA (DEFEA) EISA hardware ID's */ + +#define DEFEA_PRODUCT_ID 0x0030A310 /* DEC product 300 (no rev) */ +#define DEFEA_PROD_ID_1 0x0130A310 /* DEC product 300, rev 1 */ +#define DEFEA_PROD_ID_2 0x0230A310 /* DEC product 300, rev 2 */ +#define DEFEA_PROD_ID_3 0x0330A310 /* DEC product 300, rev 3 */ +#define DEFEA_PROD_ID_4 0x0430A310 /* DEC product 300, rev 4 */ + +/**********************************************/ +/* Digital PFI Specification v1.0 Definitions */ +/**********************************************/ + +/* PCI Configuration Space Constants */ + +#define PFI_K_LAT_TIMER_DEF 0x88 /* def max master latency timer */ +#define PFI_K_LAT_TIMER_MIN 0x20 /* min max master latency timer */ +#define PFI_K_CSR_MEM_LEN 0x80 /* 128 bytes */ +#define PFI_K_CSR_IO_LEN 0x80 /* 128 bytes */ +#define PFI_K_PKT_MEM_LEN 0x10000 /* 64K bytes */ + +/* PFI Register Offsets (starting at PDQ Register Base Address) */ + +#define PFI_K_REG_RESERVED_0 0X00000038 +#define PFI_K_REG_RESERVED_1 0X0000003C +#define PFI_K_REG_MODE_CTRL 0X00000040 +#define PFI_K_REG_STATUS 0X00000044 +#define PFI_K_REG_FIFO_WRITE 0X00000048 +#define PFI_K_REG_FIFO_READ 0X0000004C + +/* PFI Mode Control Register Constants */ + +#define PFI_MODE_M_RESERVED 0XFFFFFFF0 +#define PFI_MODE_M_TGT_ABORT_ENB 0X00000008 +#define PFI_MODE_M_PDQ_INT_ENB 0X00000004 +#define PFI_MODE_M_PFI_INT_ENB 0X00000002 +#define PFI_MODE_M_DMA_ENB 0X00000001 + +#define PFI_MODE_V_RESERVED 4 +#define PFI_MODE_V_TGT_ABORT_ENB 3 +#define PFI_MODE_V_PDQ_INT_ENB 2 +#define PFI_MODE_V_PFI_INT_ENB 1 +#define PFI_MODE_V_DMA_ENB 0 + +#define PFI_MODE_K_ALL_DISABLE 0X00000000 + +/* PFI Status Register Constants */ + +#define PFI_STATUS_M_RESERVED 0XFFFFFFC0 +#define PFI_STATUS_M_PFI_ERROR 0X00000020 /* only valid in rev 1 or later PFI */ +#define PFI_STATUS_M_PDQ_INT 0X00000010 +#define PFI_STATUS_M_PDQ_DMA_ABORT 0X00000008 +#define PFI_STATUS_M_FIFO_FULL 0X00000004 +#define PFI_STATUS_M_FIFO_EMPTY 0X00000002 +#define PFI_STATUS_M_DMA_IN_PROGRESS 0X00000001 + +#define PFI_STATUS_V_RESERVED 6 +#define PFI_STATUS_V_PFI_ERROR 5 /* only valid in rev 1 or later PFI */ +#define PFI_STATUS_V_PDQ_INT 4 +#define PFI_STATUS_V_PDQ_DMA_ABORT 3 +#define PFI_STATUS_V_FIFO_FULL 2 +#define PFI_STATUS_V_FIFO_EMPTY 1 +#define PFI_STATUS_V_DMA_IN_PROGRESS 0 + +#define DFX_FC_PRH2_PRH1_PRH0 0x54003820 /* Packet Request Header bytes + FC */ +#define DFX_PRH0_BYTE 0x20 /* Packet Request Header byte 0 */ +#define DFX_PRH1_BYTE 0x38 /* Packet Request Header byte 1 */ +#define DFX_PRH2_BYTE 0x00 /* Packet Request Header byte 2 */ + +/* Driver routine status (return) codes */ + +#define DFX_K_SUCCESS 0 /* routine succeeded */ +#define DFX_K_FAILURE 1 /* routine failed */ +#define DFX_K_OUTSTATE 2 /* bad state for command */ +#define DFX_K_HW_TIMEOUT 3 /* command timed out */ + +/* Define LLC host receive buffer min/max/default values */ + +#define RCV_BUFS_MIN 2 /* minimum pre-allocated receive buffers */ +#define RCV_BUFS_MAX 32 /* maximum pre-allocated receive buffers */ +#define RCV_BUFS_DEF 8 /* default pre-allocated receive buffers */ + +/* Define offsets into FDDI LLC or SMT receive frame buffers - used when indicating frames */ + +#define RCV_BUFF_K_DESCR 0 /* four byte FMC descriptor */ +#define RCV_BUFF_K_PADDING 4 /* three null bytes */ +#define RCV_BUFF_K_FC 7 /* one byte frame control */ +#define RCV_BUFF_K_DA 8 /* six byte destination address */ +#define RCV_BUFF_K_SA 14 /* six byte source address */ +#define RCV_BUFF_K_DATA 20 /* offset to start of packet data */ + +/* Define offsets into FDDI LLC transmit frame buffers - used when sending frames */ + +#define XMT_BUFF_K_FC 0 /* one byte frame control */ +#define XMT_BUFF_K_DA 1 /* six byte destination address */ +#define XMT_BUFF_K_SA 7 /* six byte source address */ +#define XMT_BUFF_K_DATA 13 /* offset to start of packet data */ + +/* Macro for checking a "value" is within a specific range */ + +#define IN_RANGE(value,low,high) ((value >= low) && (value <= high)) + +/* Only execute special print call when debug driver was built */ + +#ifdef DEFXX_DEBUG +#define DBG_printk(args...) printk(args) +#else +#define DBG_printk(args...) +#endif + +/* Define constants for masking/unmasking interrupts */ + +#define DFX_MASK_INTERRUPTS 1 +#define DFX_UNMASK_INTERRUPTS 0 + +/* Define structure for driver transmit descriptor block */ + +typedef struct + { + struct sk_buff *p_skb; /* ptr to skb */ + } XMT_DRIVER_DESCR; + +typedef struct DFX_board_tag + { + /* Keep virtual and physical pointers to locked, physically contiguous memory */ + + char *kmalloced; /* pci_free_consistent this on unload */ + dma_addr_t kmalloced_dma; + /* DMA handle for the above */ + PI_DESCR_BLOCK *descr_block_virt; /* PDQ descriptor block virt address */ + dma_addr_t descr_block_phys; /* PDQ descriptor block phys address */ + PI_DMA_CMD_REQ *cmd_req_virt; /* Command request buffer virt address */ + dma_addr_t cmd_req_phys; /* Command request buffer phys address */ + PI_DMA_CMD_RSP *cmd_rsp_virt; /* Command response buffer virt address */ + dma_addr_t cmd_rsp_phys; /* Command response buffer phys address */ + char *rcv_block_virt; /* LLC host receive queue buf blk virt */ + dma_addr_t rcv_block_phys; /* LLC host receive queue buf blk phys */ + PI_CONSUMER_BLOCK *cons_block_virt; /* PDQ consumer block virt address */ + dma_addr_t cons_block_phys; /* PDQ consumer block phys address */ + + /* Keep local copies of Type 1 and Type 2 register data */ + + PI_TYPE_1_PROD_REG cmd_req_reg; /* Command Request register */ + PI_TYPE_1_PROD_REG cmd_rsp_reg; /* Command Response register */ + PI_TYPE_2_PROD_REG rcv_xmt_reg; /* Type 2 (RCV/XMT) register */ + + /* Storage for unicast and multicast address entries in adapter CAM */ + + u8 uc_table[1*FDDI_K_ALEN]; + u32 uc_count; /* number of unicast addresses */ + u8 mc_table[PI_CMD_ADDR_FILTER_K_SIZE*FDDI_K_ALEN]; + u32 mc_count; /* number of multicast addresses */ + + /* Current packet filter settings */ + + u32 ind_group_prom; /* LLC individual & group frame prom mode */ + u32 group_prom; /* LLC group (multicast) frame prom mode */ + + /* Link available flag needed to determine whether to drop outgoing packet requests */ + + u32 link_available; /* is link available? */ + + /* Resources to indicate reset type when resetting adapter */ + + u32 reset_type; /* skip or rerun diagnostics */ + + /* Store pointers to receive buffers for queue processing code */ + + char *p_rcv_buff_va[PI_RCV_DATA_K_NUM_ENTRIES]; + + /* Store pointers to transmit buffers for transmit completion code */ + + XMT_DRIVER_DESCR xmt_drv_descr_blk[PI_XMT_DATA_K_NUM_ENTRIES]; + + /* Transmit spinlocks */ + + spinlock_t lock; + + /* Store device, bus-specific, and parameter information for this adapter */ + + struct net_device *dev; /* pointer to device structure */ + union { + void __iomem *mem; + int port; + } base; /* base address */ + struct device *bus_dev; + u32 full_duplex_enb; /* FDDI Full Duplex enable (1 == on, 2 == off) */ + u32 req_ttrt; /* requested TTRT value (in 80ns units) */ + u32 burst_size; /* adapter burst size (enumerated) */ + u32 rcv_bufs_to_post; /* receive buffers to post for LLC host queue */ + u8 factory_mac_addr[FDDI_K_ALEN]; /* factory (on-board) MAC address */ + + /* Common FDDI statistics structure and private counters */ + + struct fddi_statistics stats; + + u32 rcv_discards; + u32 rcv_crc_errors; + u32 rcv_frame_status_errors; + u32 rcv_length_errors; + u32 rcv_total_frames; + u32 rcv_multicast_frames; + u32 rcv_total_bytes; + + u32 xmt_discards; + u32 xmt_length_errors; + u32 xmt_total_frames; + u32 xmt_total_bytes; + } DFX_board_t; + +#endif /* #ifndef _DEFXX_H_ */ diff --git a/kernel/drivers/net/fddi/skfp/Makefile b/kernel/drivers/net/fddi/skfp/Makefile new file mode 100644 index 000000000..b0be0234a --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/Makefile @@ -0,0 +1,20 @@ +# +# Makefile for the SysKonnect FDDI PCI adapter driver +# + +obj-$(CONFIG_SKFP) += skfp.o + +skfp-objs := skfddi.o hwmtm.o fplustm.o smt.o cfm.o \ + ecm.o pcmplc.o pmf.o queue.o rmt.o \ + smtdef.o smtinit.o smttimer.o srf.o hwt.o \ + drvfbi.o ess.o + +# NOTE: +# Compiling this driver produces some warnings (and some more are +# switched off below), but I did not fix this, because the Hardware +# Module source (see skfddi.c for details) is used for different +# drivers, and fixing it for Linux might bring problems on other +# projects. To keep the source common for all those drivers (and +# thus simplify fixes to it), please do not clean it up! + +ccflags-y := -Idrivers/net/skfp -DPCI -DMEM_MAPPED_IO -Wno-strict-prototypes diff --git a/kernel/drivers/net/fddi/skfp/cfm.c b/kernel/drivers/net/fddi/skfp/cfm.c new file mode 100644 index 000000000..e395ace31 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/cfm.c @@ -0,0 +1,627 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + SMT CFM + Configuration Management + DAS with single MAC +*/ + +/* + * Hardware independent state machine implemantation + * The following external SMT functions are referenced : + * + * queue_event() + * + * The following external HW dependent functions are referenced : + * config_mux() + * + * The following HW dependent events are required : + * NONE + */ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" + +#define KERNEL +#include "h/smtstate.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)cfm.c 2.18 98/10/06 (C) SK " ; +#endif + +/* + * FSM Macros + */ +#define AFLAG 0x10 +#define GO_STATE(x) (smc->mib.fddiSMTCF_State = (x)|AFLAG) +#define ACTIONS_DONE() (smc->mib.fddiSMTCF_State &= ~AFLAG) +#define ACTIONS(x) (x|AFLAG) + +#ifdef DEBUG +/* + * symbolic state names + */ +static const char * const cfm_states[] = { + "SC0_ISOLATED","CF1","CF2","CF3","CF4", + "SC1_WRAP_A","SC2_WRAP_B","SC5_TRHU_B","SC7_WRAP_S", + "SC9_C_WRAP_A","SC10_C_WRAP_B","SC11_C_WRAP_S","SC4_THRU_A" +} ; + +/* + * symbolic event names + */ +static const char * const cfm_events[] = { + "NONE","CF_LOOP_A","CF_LOOP_B","CF_JOIN_A","CF_JOIN_B" +} ; +#endif + +/* + * map from state to downstream port type + */ +static const unsigned char cf_to_ptype[] = { + TNONE,TNONE,TNONE,TNONE,TNONE, + TNONE,TB,TB,TS, + TA,TB,TS,TB +} ; + +/* + * CEM port states + */ +#define CEM_PST_DOWN 0 +#define CEM_PST_UP 1 +#define CEM_PST_HOLD 2 +/* define portstate array only for A and B port */ +/* Do this within the smc structure (use in multiple cards) */ + +/* + * all Globals are defined in smc.h + * struct s_cfm + */ + +/* + * function declarations + */ +static void cfm_fsm(struct s_smc *smc, int cmd); + +/* + init CFM state machine + clear all CFM vars and flags +*/ +void cfm_init(struct s_smc *smc) +{ + smc->mib.fddiSMTCF_State = ACTIONS(SC0_ISOLATED) ; + smc->r.rm_join = 0 ; + smc->r.rm_loop = 0 ; + smc->y[PA].scrub = 0 ; + smc->y[PB].scrub = 0 ; + smc->y[PA].cem_pst = CEM_PST_DOWN ; + smc->y[PB].cem_pst = CEM_PST_DOWN ; +} + +/* Some terms conditions used by the selection criteria */ +#define THRU_ENABLED(smc) (smc->y[PA].pc_mode != PM_TREE && \ + smc->y[PB].pc_mode != PM_TREE) +/* Selection criteria for the ports */ +static void selection_criteria (struct s_smc *smc, struct s_phy *phy) +{ + + switch (phy->mib->fddiPORTMy_Type) { + case TA: + if ( !THRU_ENABLED(smc) && smc->y[PB].cf_join ) { + phy->wc_flag = TRUE ; + } else { + phy->wc_flag = FALSE ; + } + + break; + case TB: + /* take precedence over PA */ + phy->wc_flag = FALSE ; + break; + case TS: + phy->wc_flag = FALSE ; + break; + case TM: + phy->wc_flag = FALSE ; + break; + } + +} + +void all_selection_criteria(struct s_smc *smc) +{ + struct s_phy *phy ; + int p ; + + for ( p = 0,phy = smc->y ; p < NUMPHYS; p++, phy++ ) { + /* Do the selection criteria */ + selection_criteria (smc,phy); + } +} + +static void cem_priv_state(struct s_smc *smc, int event) +/* State machine for private PORT states: used to optimize dual homing */ +{ + int np; /* Number of the port */ + int i; + + /* Do this only in a DAS */ + if (smc->s.sas != SMT_DAS ) + return ; + + np = event - CF_JOIN; + + if (np != PA && np != PB) { + return ; + } + /* Change the port state according to the event (portnumber) */ + if (smc->y[np].cf_join) { + smc->y[np].cem_pst = CEM_PST_UP ; + } else if (!smc->y[np].wc_flag) { + /* set the port to done only if it is not withheld */ + smc->y[np].cem_pst = CEM_PST_DOWN ; + } + + /* Don't set an hold port to down */ + + /* Check all ports of restart conditions */ + for (i = 0 ; i < 2 ; i ++ ) { + /* Check all port for PORT is on hold and no withhold is done */ + if ( smc->y[i].cem_pst == CEM_PST_HOLD && !smc->y[i].wc_flag ) { + smc->y[i].cem_pst = CEM_PST_DOWN; + queue_event(smc,(int)(EVENT_PCM+i),PC_START) ; + } + if ( smc->y[i].cem_pst == CEM_PST_UP && smc->y[i].wc_flag ) { + smc->y[i].cem_pst = CEM_PST_HOLD; + queue_event(smc,(int)(EVENT_PCM+i),PC_START) ; + } + if ( smc->y[i].cem_pst == CEM_PST_DOWN && smc->y[i].wc_flag ) { + /* + * The port must be restarted when the wc_flag + * will be reset. So set the port on hold. + */ + smc->y[i].cem_pst = CEM_PST_HOLD; + } + } + return ; +} + +/* + CFM state machine + called by dispatcher + + do + display state change + process event + until SM is stable +*/ +void cfm(struct s_smc *smc, int event) +{ + int state ; /* remember last state */ + int cond ; + int oldstate ; + + /* We will do the following: */ + /* - compute the variable WC_Flag for every port (This is where */ + /* we can extend the requested path checking !!) */ + /* - do the old (SMT 6.2 like) state machine */ + /* - do the resulting station states */ + + all_selection_criteria (smc); + + /* We will check now whether a state transition is allowed or not */ + /* - change the portstates */ + cem_priv_state (smc, event); + + oldstate = smc->mib.fddiSMTCF_State ; + do { + DB_CFM("CFM : state %s%s", + (smc->mib.fddiSMTCF_State & AFLAG) ? "ACTIONS " : "", + cfm_states[smc->mib.fddiSMTCF_State & ~AFLAG]) ; + DB_CFM(" event %s\n",cfm_events[event],0) ; + state = smc->mib.fddiSMTCF_State ; + cfm_fsm(smc,event) ; + event = 0 ; + } while (state != smc->mib.fddiSMTCF_State) ; + +#ifndef SLIM_SMT + /* + * check peer wrap condition + */ + cond = FALSE ; + if ( (smc->mib.fddiSMTCF_State == SC9_C_WRAP_A && + smc->y[PA].pc_mode == PM_PEER) || + (smc->mib.fddiSMTCF_State == SC10_C_WRAP_B && + smc->y[PB].pc_mode == PM_PEER) || + (smc->mib.fddiSMTCF_State == SC11_C_WRAP_S && + smc->y[PS].pc_mode == PM_PEER && + smc->y[PS].mib->fddiPORTNeighborType != TS ) ) { + cond = TRUE ; + } + if (cond != smc->mib.fddiSMTPeerWrapFlag) + smt_srf_event(smc,SMT_COND_SMT_PEER_WRAP,0,cond) ; + +#if 0 + /* + * Don't send ever MAC_PATH_CHANGE events. Our MAC is hard-wired + * to the primary path. + */ + /* + * path change + */ + if (smc->mib.fddiSMTCF_State != oldstate) { + smt_srf_event(smc,SMT_EVENT_MAC_PATH_CHANGE,INDEX_MAC,0) ; + } +#endif +#endif /* no SLIM_SMT */ + + /* + * set MAC port type + */ + smc->mib.m[MAC0].fddiMACDownstreamPORTType = + cf_to_ptype[smc->mib.fddiSMTCF_State] ; + cfm_state_change(smc,(int)smc->mib.fddiSMTCF_State) ; +} + +/* + process CFM event +*/ +/*ARGSUSED1*/ +static void cfm_fsm(struct s_smc *smc, int cmd) +{ + switch(smc->mib.fddiSMTCF_State) { + case ACTIONS(SC0_ISOLATED) : + smc->mib.p[PA].fddiPORTCurrentPath = MIB_PATH_ISOLATED ; + smc->mib.p[PB].fddiPORTCurrentPath = MIB_PATH_ISOLATED ; + smc->mib.p[PA].fddiPORTMACPlacement = 0 ; + smc->mib.p[PB].fddiPORTMACPlacement = 0 ; + smc->mib.fddiSMTStationStatus = MIB_SMT_STASTA_SEPA ; + config_mux(smc,MUX_ISOLATE) ; /* configure PHY Mux */ + smc->r.rm_loop = FALSE ; + smc->r.rm_join = FALSE ; + queue_event(smc,EVENT_RMT,RM_JOIN) ;/* signal RMT */ + /* Don't do the WC-Flag changing here */ + ACTIONS_DONE() ; + DB_CFMN(1,"CFM : %s\n",cfm_states[smc->mib.fddiSMTCF_State],0) ; + break; + case SC0_ISOLATED : + /*SC07*/ + /*SAS port can be PA or PB ! */ + if (smc->s.sas && (smc->y[PA].cf_join || smc->y[PA].cf_loop || + smc->y[PB].cf_join || smc->y[PB].cf_loop)) { + GO_STATE(SC11_C_WRAP_S) ; + break ; + } + /*SC01*/ + if ((smc->y[PA].cem_pst == CEM_PST_UP && smc->y[PA].cf_join && + !smc->y[PA].wc_flag) || smc->y[PA].cf_loop) { + GO_STATE(SC9_C_WRAP_A) ; + break ; + } + /*SC02*/ + if ((smc->y[PB].cem_pst == CEM_PST_UP && smc->y[PB].cf_join && + !smc->y[PB].wc_flag) || smc->y[PB].cf_loop) { + GO_STATE(SC10_C_WRAP_B) ; + break ; + } + break ; + case ACTIONS(SC9_C_WRAP_A) : + smc->mib.p[PA].fddiPORTCurrentPath = MIB_PATH_CONCATENATED ; + smc->mib.p[PB].fddiPORTCurrentPath = MIB_PATH_ISOLATED ; + smc->mib.p[PA].fddiPORTMACPlacement = INDEX_MAC ; + smc->mib.p[PB].fddiPORTMACPlacement = 0 ; + smc->mib.fddiSMTStationStatus = MIB_SMT_STASTA_CON ; + config_mux(smc,MUX_WRAPA) ; /* configure PHY mux */ + if (smc->y[PA].cf_loop) { + smc->r.rm_join = FALSE ; + smc->r.rm_loop = TRUE ; + queue_event(smc,EVENT_RMT,RM_LOOP) ;/* signal RMT */ + } + if (smc->y[PA].cf_join) { + smc->r.rm_loop = FALSE ; + smc->r.rm_join = TRUE ; + queue_event(smc,EVENT_RMT,RM_JOIN) ;/* signal RMT */ + } + ACTIONS_DONE() ; + DB_CFMN(1,"CFM : %s\n",cfm_states[smc->mib.fddiSMTCF_State],0) ; + break ; + case SC9_C_WRAP_A : + /*SC10*/ + if ( (smc->y[PA].wc_flag || !smc->y[PA].cf_join) && + !smc->y[PA].cf_loop ) { + GO_STATE(SC0_ISOLATED) ; + break ; + } + /*SC12*/ + else if ( (smc->y[PB].cf_loop && smc->y[PA].cf_join && + smc->y[PA].cem_pst == CEM_PST_UP) || + ((smc->y[PB].cf_loop || + (smc->y[PB].cf_join && + smc->y[PB].cem_pst == CEM_PST_UP)) && + (smc->y[PA].pc_mode == PM_TREE || + smc->y[PB].pc_mode == PM_TREE))) { + smc->y[PA].scrub = TRUE ; + GO_STATE(SC10_C_WRAP_B) ; + break ; + } + /*SC14*/ + else if (!smc->s.attach_s && + smc->y[PA].cf_join && + smc->y[PA].cem_pst == CEM_PST_UP && + smc->y[PA].pc_mode == PM_PEER && smc->y[PB].cf_join && + smc->y[PB].cem_pst == CEM_PST_UP && + smc->y[PB].pc_mode == PM_PEER) { + smc->y[PA].scrub = TRUE ; + smc->y[PB].scrub = TRUE ; + GO_STATE(SC4_THRU_A) ; + break ; + } + /*SC15*/ + else if ( smc->s.attach_s && + smc->y[PA].cf_join && + smc->y[PA].cem_pst == CEM_PST_UP && + smc->y[PA].pc_mode == PM_PEER && + smc->y[PB].cf_join && + smc->y[PB].cem_pst == CEM_PST_UP && + smc->y[PB].pc_mode == PM_PEER) { + smc->y[PA].scrub = TRUE ; + smc->y[PB].scrub = TRUE ; + GO_STATE(SC5_THRU_B) ; + break ; + } + break ; + case ACTIONS(SC10_C_WRAP_B) : + smc->mib.p[PA].fddiPORTCurrentPath = MIB_PATH_ISOLATED ; + smc->mib.p[PB].fddiPORTCurrentPath = MIB_PATH_CONCATENATED ; + smc->mib.p[PA].fddiPORTMACPlacement = 0 ; + smc->mib.p[PB].fddiPORTMACPlacement = INDEX_MAC ; + smc->mib.fddiSMTStationStatus = MIB_SMT_STASTA_CON ; + config_mux(smc,MUX_WRAPB) ; /* configure PHY mux */ + if (smc->y[PB].cf_loop) { + smc->r.rm_join = FALSE ; + smc->r.rm_loop = TRUE ; + queue_event(smc,EVENT_RMT,RM_LOOP) ;/* signal RMT */ + } + if (smc->y[PB].cf_join) { + smc->r.rm_loop = FALSE ; + smc->r.rm_join = TRUE ; + queue_event(smc,EVENT_RMT,RM_JOIN) ;/* signal RMT */ + } + ACTIONS_DONE() ; + DB_CFMN(1,"CFM : %s\n",cfm_states[smc->mib.fddiSMTCF_State],0) ; + break ; + case SC10_C_WRAP_B : + /*SC20*/ + if ( !smc->y[PB].cf_join && !smc->y[PB].cf_loop ) { + GO_STATE(SC0_ISOLATED) ; + break ; + } + /*SC21*/ + else if ( smc->y[PA].cf_loop && smc->y[PA].pc_mode == PM_PEER && + smc->y[PB].cf_join && smc->y[PB].pc_mode == PM_PEER) { + smc->y[PB].scrub = TRUE ; + GO_STATE(SC9_C_WRAP_A) ; + break ; + } + /*SC24*/ + else if (!smc->s.attach_s && + smc->y[PA].cf_join && smc->y[PA].pc_mode == PM_PEER && + smc->y[PB].cf_join && smc->y[PB].pc_mode == PM_PEER) { + smc->y[PA].scrub = TRUE ; + smc->y[PB].scrub = TRUE ; + GO_STATE(SC4_THRU_A) ; + break ; + } + /*SC25*/ + else if ( smc->s.attach_s && + smc->y[PA].cf_join && smc->y[PA].pc_mode == PM_PEER && + smc->y[PB].cf_join && smc->y[PB].pc_mode == PM_PEER) { + smc->y[PA].scrub = TRUE ; + smc->y[PB].scrub = TRUE ; + GO_STATE(SC5_THRU_B) ; + break ; + } + break ; + case ACTIONS(SC4_THRU_A) : + smc->mib.p[PA].fddiPORTCurrentPath = MIB_PATH_THRU ; + smc->mib.p[PB].fddiPORTCurrentPath = MIB_PATH_THRU ; + smc->mib.p[PA].fddiPORTMACPlacement = 0 ; + smc->mib.p[PB].fddiPORTMACPlacement = INDEX_MAC ; + smc->mib.fddiSMTStationStatus = MIB_SMT_STASTA_THRU ; + config_mux(smc,MUX_THRUA) ; /* configure PHY mux */ + smc->r.rm_loop = FALSE ; + smc->r.rm_join = TRUE ; + queue_event(smc,EVENT_RMT,RM_JOIN) ;/* signal RMT */ + ACTIONS_DONE() ; + DB_CFMN(1,"CFM : %s\n",cfm_states[smc->mib.fddiSMTCF_State],0) ; + break ; + case SC4_THRU_A : + /*SC41*/ + if (smc->y[PB].wc_flag || !smc->y[PB].cf_join) { + smc->y[PA].scrub = TRUE ; + GO_STATE(SC9_C_WRAP_A) ; + break ; + } + /*SC42*/ + else if (!smc->y[PA].cf_join || smc->y[PA].wc_flag) { + smc->y[PB].scrub = TRUE ; + GO_STATE(SC10_C_WRAP_B) ; + break ; + } + /*SC45*/ + else if (smc->s.attach_s) { + smc->y[PB].scrub = TRUE ; + GO_STATE(SC5_THRU_B) ; + break ; + } + break ; + case ACTIONS(SC5_THRU_B) : + smc->mib.p[PA].fddiPORTCurrentPath = MIB_PATH_THRU ; + smc->mib.p[PB].fddiPORTCurrentPath = MIB_PATH_THRU ; + smc->mib.p[PA].fddiPORTMACPlacement = INDEX_MAC ; + smc->mib.p[PB].fddiPORTMACPlacement = 0 ; + smc->mib.fddiSMTStationStatus = MIB_SMT_STASTA_THRU ; + config_mux(smc,MUX_THRUB) ; /* configure PHY mux */ + smc->r.rm_loop = FALSE ; + smc->r.rm_join = TRUE ; + queue_event(smc,EVENT_RMT,RM_JOIN) ;/* signal RMT */ + ACTIONS_DONE() ; + DB_CFMN(1,"CFM : %s\n",cfm_states[smc->mib.fddiSMTCF_State],0) ; + break ; + case SC5_THRU_B : + /*SC51*/ + if (!smc->y[PB].cf_join || smc->y[PB].wc_flag) { + smc->y[PA].scrub = TRUE ; + GO_STATE(SC9_C_WRAP_A) ; + break ; + } + /*SC52*/ + else if (!smc->y[PA].cf_join || smc->y[PA].wc_flag) { + smc->y[PB].scrub = TRUE ; + GO_STATE(SC10_C_WRAP_B) ; + break ; + } + /*SC54*/ + else if (!smc->s.attach_s) { + smc->y[PA].scrub = TRUE ; + GO_STATE(SC4_THRU_A) ; + break ; + } + break ; + case ACTIONS(SC11_C_WRAP_S) : + smc->mib.p[PS].fddiPORTCurrentPath = MIB_PATH_CONCATENATED ; + smc->mib.p[PS].fddiPORTMACPlacement = INDEX_MAC ; + smc->mib.fddiSMTStationStatus = MIB_SMT_STASTA_CON ; + config_mux(smc,MUX_WRAPS) ; /* configure PHY mux */ + if (smc->y[PA].cf_loop || smc->y[PB].cf_loop) { + smc->r.rm_join = FALSE ; + smc->r.rm_loop = TRUE ; + queue_event(smc,EVENT_RMT,RM_LOOP) ;/* signal RMT */ + } + if (smc->y[PA].cf_join || smc->y[PB].cf_join) { + smc->r.rm_loop = FALSE ; + smc->r.rm_join = TRUE ; + queue_event(smc,EVENT_RMT,RM_JOIN) ;/* signal RMT */ + } + ACTIONS_DONE() ; + DB_CFMN(1,"CFM : %s\n",cfm_states[smc->mib.fddiSMTCF_State],0) ; + break ; + case SC11_C_WRAP_S : + /*SC70*/ + if ( !smc->y[PA].cf_join && !smc->y[PA].cf_loop && + !smc->y[PB].cf_join && !smc->y[PB].cf_loop) { + GO_STATE(SC0_ISOLATED) ; + break ; + } + break ; + default: + SMT_PANIC(smc,SMT_E0106, SMT_E0106_MSG) ; + break; + } +} + +/* + * get MAC's input Port + * return : + * PA or PB + */ +int cfm_get_mac_input(struct s_smc *smc) +{ + return (smc->mib.fddiSMTCF_State == SC10_C_WRAP_B || + smc->mib.fddiSMTCF_State == SC5_THRU_B) ? PB : PA; +} + +/* + * get MAC's output Port + * return : + * PA or PB + */ +int cfm_get_mac_output(struct s_smc *smc) +{ + return (smc->mib.fddiSMTCF_State == SC10_C_WRAP_B || + smc->mib.fddiSMTCF_State == SC4_THRU_A) ? PB : PA; +} + +static char path_iso[] = { + 0,0, 0,RES_PORT, 0,PA + INDEX_PORT, 0,PATH_ISO, + 0,0, 0,RES_MAC, 0,INDEX_MAC, 0,PATH_ISO, + 0,0, 0,RES_PORT, 0,PB + INDEX_PORT, 0,PATH_ISO +} ; + +static char path_wrap_a[] = { + 0,0, 0,RES_PORT, 0,PA + INDEX_PORT, 0,PATH_PRIM, + 0,0, 0,RES_MAC, 0,INDEX_MAC, 0,PATH_PRIM, + 0,0, 0,RES_PORT, 0,PB + INDEX_PORT, 0,PATH_ISO +} ; + +static char path_wrap_b[] = { + 0,0, 0,RES_PORT, 0,PB + INDEX_PORT, 0,PATH_PRIM, + 0,0, 0,RES_MAC, 0,INDEX_MAC, 0,PATH_PRIM, + 0,0, 0,RES_PORT, 0,PA + INDEX_PORT, 0,PATH_ISO +} ; + +static char path_thru[] = { + 0,0, 0,RES_PORT, 0,PA + INDEX_PORT, 0,PATH_PRIM, + 0,0, 0,RES_MAC, 0,INDEX_MAC, 0,PATH_PRIM, + 0,0, 0,RES_PORT, 0,PB + INDEX_PORT, 0,PATH_PRIM +} ; + +static char path_wrap_s[] = { + 0,0, 0,RES_PORT, 0,PS + INDEX_PORT, 0,PATH_PRIM, + 0,0, 0,RES_MAC, 0,INDEX_MAC, 0,PATH_PRIM, +} ; + +static char path_iso_s[] = { + 0,0, 0,RES_PORT, 0,PS + INDEX_PORT, 0,PATH_ISO, + 0,0, 0,RES_MAC, 0,INDEX_MAC, 0,PATH_ISO, +} ; + +int cem_build_path(struct s_smc *smc, char *to, int path_index) +{ + char *path ; + int len ; + + switch (smc->mib.fddiSMTCF_State) { + default : + case SC0_ISOLATED : + path = smc->s.sas ? path_iso_s : path_iso ; + len = smc->s.sas ? sizeof(path_iso_s) : sizeof(path_iso) ; + break ; + case SC9_C_WRAP_A : + path = path_wrap_a ; + len = sizeof(path_wrap_a) ; + break ; + case SC10_C_WRAP_B : + path = path_wrap_b ; + len = sizeof(path_wrap_b) ; + break ; + case SC4_THRU_A : + path = path_thru ; + len = sizeof(path_thru) ; + break ; + case SC11_C_WRAP_S : + path = path_wrap_s ; + len = sizeof(path_wrap_s) ; + break ; + } + memcpy(to,path,len) ; + + LINT_USE(path_index); + + return len; +} diff --git a/kernel/drivers/net/fddi/skfp/drvfbi.c b/kernel/drivers/net/fddi/skfp/drvfbi.c new file mode 100644 index 000000000..07da97c30 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/drvfbi.c @@ -0,0 +1,584 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * FBI board dependent Driver for SMT and LLC + */ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/supern_2.h" +#include "h/skfbiinc.h" +#include <linux/bitrev.h> + +#ifndef lint +static const char ID_sccs[] = "@(#)drvfbi.c 1.63 99/02/11 (C) SK " ; +#endif + +/* + * PCM active state + */ +#define PC8_ACTIVE 8 + +#define LED_Y_ON 0x11 /* Used for ring up/down indication */ +#define LED_Y_OFF 0x10 + + +#define MS2BCLK(x) ((x)*12500L) + +/* + * valid configuration values are: + */ + +/* + * xPOS_ID:xxxx + * | \ / + * | \/ + * | --------------------- the patched POS_ID of the Adapter + * | xxxx = (Vendor ID low byte, + * | Vendor ID high byte, + * | Device ID low byte, + * | Device ID high byte) + * +------------------------------ the patched oem_id must be + * 'S' for SK or 'I' for IBM + * this is a short id for the driver. + */ +#ifndef MULT_OEM +#ifndef OEM_CONCEPT +const u_char oem_id[] = "xPOS_ID:xxxx" ; +#else /* OEM_CONCEPT */ +const u_char oem_id[] = OEM_ID ; +#endif /* OEM_CONCEPT */ +#define ID_BYTE0 8 +#define OEMID(smc,i) oem_id[ID_BYTE0 + i] +#else /* MULT_OEM */ +const struct s_oem_ids oem_ids[] = { +#include "oemids.h" +{0} +}; +#define OEMID(smc,i) smc->hw.oem_id->oi_id[i] +#endif /* MULT_OEM */ + +/* Prototypes of external functions */ +#ifdef AIX +extern int AIX_vpdReadByte() ; +#endif + + +/* Prototype of a local function. */ +static void smt_stop_watchdog(struct s_smc *smc); + +/* + * FDDI card reset + */ +static void card_start(struct s_smc *smc) +{ + int i ; +#ifdef PCI + u_char rev_id ; + u_short word; +#endif + + smt_stop_watchdog(smc) ; + +#ifdef PCI + /* + * make sure no transfer activity is pending + */ + outpw(FM_A(FM_MDREG1),FM_MINIT) ; + outp(ADDR(B0_CTRL), CTRL_HPI_SET) ; + hwt_wait_time(smc,hwt_quick_read(smc),MS2BCLK(10)) ; + /* + * now reset everything + */ + outp(ADDR(B0_CTRL),CTRL_RST_SET) ; /* reset for all chips */ + i = (int) inp(ADDR(B0_CTRL)) ; /* do dummy read */ + SK_UNUSED(i) ; /* Make LINT happy. */ + outp(ADDR(B0_CTRL), CTRL_RST_CLR) ; + + /* + * Reset all bits in the PCI STATUS register + */ + outp(ADDR(B0_TST_CTRL), TST_CFG_WRITE_ON) ; /* enable for writes */ + word = inpw(PCI_C(PCI_STATUS)) ; + outpw(PCI_C(PCI_STATUS), word | PCI_ERRBITS) ; + outp(ADDR(B0_TST_CTRL), TST_CFG_WRITE_OFF) ; /* disable writes */ + + /* + * Release the reset of all the State machines + * Release Master_Reset + * Release HPI_SM_Reset + */ + outp(ADDR(B0_CTRL), CTRL_MRST_CLR|CTRL_HPI_CLR) ; + + /* + * determine the adapter type + * Note: Do it here, because some drivers may call card_start() once + * at very first before any other initialization functions is + * executed. + */ + rev_id = inp(PCI_C(PCI_REV_ID)) ; + if ((rev_id & 0xf0) == SK_ML_ID_1 || (rev_id & 0xf0) == SK_ML_ID_2) { + smc->hw.hw_is_64bit = TRUE ; + } else { + smc->hw.hw_is_64bit = FALSE ; + } + + /* + * Watermark initialization + */ + if (!smc->hw.hw_is_64bit) { + outpd(ADDR(B4_R1_F), RX_WATERMARK) ; + outpd(ADDR(B5_XA_F), TX_WATERMARK) ; + outpd(ADDR(B5_XS_F), TX_WATERMARK) ; + } + + outp(ADDR(B0_CTRL),CTRL_RST_CLR) ; /* clear the reset chips */ + outp(ADDR(B0_LED),LED_GA_OFF|LED_MY_ON|LED_GB_OFF) ; /* ye LED on */ + + /* init the timer value for the watch dog 2,5 minutes */ + outpd(ADDR(B2_WDOG_INI),0x6FC23AC0) ; + + /* initialize the ISR mask */ + smc->hw.is_imask = ISR_MASK ; + smc->hw.hw_state = STOPPED ; +#endif + GET_PAGE(0) ; /* necessary for BOOT */ +} + +void card_stop(struct s_smc *smc) +{ + smt_stop_watchdog(smc) ; + smc->hw.mac_ring_is_up = 0 ; /* ring down */ + +#ifdef PCI + /* + * make sure no transfer activity is pending + */ + outpw(FM_A(FM_MDREG1),FM_MINIT) ; + outp(ADDR(B0_CTRL), CTRL_HPI_SET) ; + hwt_wait_time(smc,hwt_quick_read(smc),MS2BCLK(10)) ; + /* + * now reset everything + */ + outp(ADDR(B0_CTRL),CTRL_RST_SET) ; /* reset for all chips */ + outp(ADDR(B0_CTRL),CTRL_RST_CLR) ; /* reset for all chips */ + outp(ADDR(B0_LED),LED_GA_OFF|LED_MY_OFF|LED_GB_OFF) ; /* all LEDs off */ + smc->hw.hw_state = STOPPED ; +#endif +} +/*--------------------------- ISR handling ----------------------------------*/ + +void mac1_irq(struct s_smc *smc, u_short stu, u_short stl) +{ + int restart_tx = 0 ; +again: + + /* + * parity error: note encoding error is not possible in tag mode + */ + if (stl & (FM_SPCEPDS | /* parity err. syn.q.*/ + FM_SPCEPDA0 | /* parity err. a.q.0 */ + FM_SPCEPDA1)) { /* parity err. a.q.1 */ + SMT_PANIC(smc,SMT_E0134, SMT_E0134_MSG) ; + } + /* + * buffer underrun: can only occur if a tx threshold is specified + */ + if (stl & (FM_STBURS | /* tx buffer underrun syn.q.*/ + FM_STBURA0 | /* tx buffer underrun a.q.0 */ + FM_STBURA1)) { /* tx buffer underrun a.q.2 */ + SMT_PANIC(smc,SMT_E0133, SMT_E0133_MSG) ; + } + + if ( (stu & (FM_SXMTABT | /* transmit abort */ + FM_STXABRS | /* syn. tx abort */ + FM_STXABRA0)) || /* asyn. tx abort */ + (stl & (FM_SQLCKS | /* lock for syn. q. */ + FM_SQLCKA0)) ) { /* lock for asyn. q. */ + formac_tx_restart(smc) ; /* init tx */ + restart_tx = 1 ; + stu = inpw(FM_A(FM_ST1U)) ; + stl = inpw(FM_A(FM_ST1L)) ; + stu &= ~ (FM_STECFRMA0 | FM_STEFRMA0 | FM_STEFRMS) ; + if (stu || stl) + goto again ; + } + + if (stu & (FM_STEFRMA0 | /* end of asyn tx */ + FM_STEFRMS)) { /* end of sync tx */ + restart_tx = 1 ; + } + + if (restart_tx) + llc_restart_tx(smc) ; +} + +/* + * interrupt source= plc1 + * this function is called in nwfbisr.asm + */ +void plc1_irq(struct s_smc *smc) +{ + u_short st = inpw(PLC(PB,PL_INTR_EVENT)) ; + + plc_irq(smc,PB,st) ; +} + +/* + * interrupt source= plc2 + * this function is called in nwfbisr.asm + */ +void plc2_irq(struct s_smc *smc) +{ + u_short st = inpw(PLC(PA,PL_INTR_EVENT)) ; + + plc_irq(smc,PA,st) ; +} + + +/* + * interrupt source= timer + */ +void timer_irq(struct s_smc *smc) +{ + hwt_restart(smc); + smc->hw.t_stop = smc->hw.t_start; + smt_timer_done(smc) ; +} + +/* + * return S-port (PA or PB) + */ +int pcm_get_s_port(struct s_smc *smc) +{ + SK_UNUSED(smc) ; + return PS; +} + +/* + * Station Label = "FDDI-XYZ" where + * + * X = connector type + * Y = PMD type + * Z = port type + */ +#define STATION_LABEL_CONNECTOR_OFFSET 5 +#define STATION_LABEL_PMD_OFFSET 6 +#define STATION_LABEL_PORT_OFFSET 7 + +void read_address(struct s_smc *smc, u_char *mac_addr) +{ + char ConnectorType ; + char PmdType ; + int i ; + +#ifdef PCI + for (i = 0; i < 6; i++) { /* read mac address from board */ + smc->hw.fddi_phys_addr.a[i] = + bitrev8(inp(ADDR(B2_MAC_0+i))); + } +#endif + + ConnectorType = inp(ADDR(B2_CONN_TYP)) ; + PmdType = inp(ADDR(B2_PMD_TYP)) ; + + smc->y[PA].pmd_type[PMD_SK_CONN] = + smc->y[PB].pmd_type[PMD_SK_CONN] = ConnectorType ; + smc->y[PA].pmd_type[PMD_SK_PMD ] = + smc->y[PB].pmd_type[PMD_SK_PMD ] = PmdType ; + + if (mac_addr) { + for (i = 0; i < 6 ;i++) { + smc->hw.fddi_canon_addr.a[i] = mac_addr[i] ; + smc->hw.fddi_home_addr.a[i] = bitrev8(mac_addr[i]); + } + return ; + } + smc->hw.fddi_home_addr = smc->hw.fddi_phys_addr ; + + for (i = 0; i < 6 ;i++) { + smc->hw.fddi_canon_addr.a[i] = + bitrev8(smc->hw.fddi_phys_addr.a[i]); + } +} + +/* + * FDDI card soft reset + */ +void init_board(struct s_smc *smc, u_char *mac_addr) +{ + card_start(smc) ; + read_address(smc,mac_addr) ; + + if (!(inp(ADDR(B0_DAS)) & DAS_AVAIL)) + smc->s.sas = SMT_SAS ; /* Single att. station */ + else + smc->s.sas = SMT_DAS ; /* Dual att. station */ + + if (!(inp(ADDR(B0_DAS)) & DAS_BYP_ST)) + smc->mib.fddiSMTBypassPresent = 0 ; + /* without opt. bypass */ + else + smc->mib.fddiSMTBypassPresent = 1 ; + /* with opt. bypass */ +} + +/* + * insert or deinsert optical bypass (called by ECM) + */ +void sm_pm_bypass_req(struct s_smc *smc, int mode) +{ + DB_ECMN(1,"ECM : sm_pm_bypass_req(%s)\n",(mode == BP_INSERT) ? + "BP_INSERT" : "BP_DEINSERT",0) ; + + if (smc->s.sas != SMT_DAS) + return ; + +#ifdef PCI + switch(mode) { + case BP_INSERT : + outp(ADDR(B0_DAS),DAS_BYP_INS) ; /* insert station */ + break ; + case BP_DEINSERT : + outp(ADDR(B0_DAS),DAS_BYP_RMV) ; /* bypass station */ + break ; + } +#endif +} + +/* + * check if bypass connected + */ +int sm_pm_bypass_present(struct s_smc *smc) +{ + return (inp(ADDR(B0_DAS)) & DAS_BYP_ST) ? TRUE : FALSE; +} + +void plc_clear_irq(struct s_smc *smc, int p) +{ + SK_UNUSED(p) ; + + SK_UNUSED(smc) ; +} + + +/* + * led_indication called by rmt_indication() and + * pcm_state_change() + * + * Input: + * smc: SMT context + * led_event: + * 0 Only switch green LEDs according to their respective PCM state + * LED_Y_OFF just switch yellow LED off + * LED_Y_ON just switch yello LED on + */ +static void led_indication(struct s_smc *smc, int led_event) +{ + /* use smc->hw.mac_ring_is_up == TRUE + * as indication for Ring Operational + */ + u_short led_state ; + struct s_phy *phy ; + struct fddi_mib_p *mib_a ; + struct fddi_mib_p *mib_b ; + + phy = &smc->y[PA] ; + mib_a = phy->mib ; + phy = &smc->y[PB] ; + mib_b = phy->mib ; + +#ifdef PCI + led_state = 0 ; + + /* Ring up = yellow led OFF*/ + if (led_event == LED_Y_ON) { + led_state |= LED_MY_ON ; + } + else if (led_event == LED_Y_OFF) { + led_state |= LED_MY_OFF ; + } + else { /* PCM state changed */ + /* Link at Port A/S = green led A ON */ + if (mib_a->fddiPORTPCMState == PC8_ACTIVE) { + led_state |= LED_GA_ON ; + } + else { + led_state |= LED_GA_OFF ; + } + + /* Link at Port B = green led B ON */ + if (mib_b->fddiPORTPCMState == PC8_ACTIVE) { + led_state |= LED_GB_ON ; + } + else { + led_state |= LED_GB_OFF ; + } + } + + outp(ADDR(B0_LED), led_state) ; +#endif /* PCI */ + +} + + +void pcm_state_change(struct s_smc *smc, int plc, int p_state) +{ + /* + * the current implementation of pcm_state_change() in the driver + * parts must be renamed to drv_pcm_state_change() which will be called + * now after led_indication. + */ + DRV_PCM_STATE_CHANGE(smc,plc,p_state) ; + + led_indication(smc,0) ; +} + + +void rmt_indication(struct s_smc *smc, int i) +{ + /* Call a driver special function if defined */ + DRV_RMT_INDICATION(smc,i) ; + + led_indication(smc, i ? LED_Y_OFF : LED_Y_ON) ; +} + + +/* + * llc_recover_tx called by init_tx (fplus.c) + */ +void llc_recover_tx(struct s_smc *smc) +{ +#ifdef LOAD_GEN + extern int load_gen_flag ; + + load_gen_flag = 0 ; +#endif +#ifndef SYNC + smc->hw.n_a_send= 0 ; +#else + SK_UNUSED(smc) ; +#endif +} + +#ifdef MULT_OEM +static int is_equal_num(char comp1[], char comp2[], int num) +{ + int i ; + + for (i = 0 ; i < num ; i++) { + if (comp1[i] != comp2[i]) + return 0; + } + return 1; +} /* is_equal_num */ + + +/* + * set the OEM ID defaults, and test the contents of the OEM data base + * The default OEM is the first ACTIVE entry in the OEM data base + * + * returns: 0 success + * 1 error in data base + * 2 data base empty + * 3 no active entry + */ +int set_oi_id_def(struct s_smc *smc) +{ + int sel_id ; + int i ; + int act_entries ; + + i = 0 ; + sel_id = -1 ; + act_entries = FALSE ; + smc->hw.oem_id = 0 ; + smc->hw.oem_min_status = OI_STAT_ACTIVE ; + + /* check OEM data base */ + while (oem_ids[i].oi_status) { + switch (oem_ids[i].oi_status) { + case OI_STAT_ACTIVE: + act_entries = TRUE ; /* we have active IDs */ + if (sel_id == -1) + sel_id = i ; /* save the first active ID */ + case OI_STAT_VALID: + case OI_STAT_PRESENT: + i++ ; + break ; /* entry ok */ + default: + return 1; /* invalid oi_status */ + } + } + + if (i == 0) + return 2; + if (!act_entries) + return 3; + + /* ok, we have a valid OEM data base with an active entry */ + smc->hw.oem_id = (struct s_oem_ids *) &oem_ids[sel_id] ; + return 0; +} +#endif /* MULT_OEM */ + +void driver_get_bia(struct s_smc *smc, struct fddi_addr *bia_addr) +{ + int i ; + + for (i = 0 ; i < 6 ; i++) + bia_addr->a[i] = bitrev8(smc->hw.fddi_phys_addr.a[i]); +} + +void smt_start_watchdog(struct s_smc *smc) +{ + SK_UNUSED(smc) ; /* Make LINT happy. */ + +#ifndef DEBUG + +#ifdef PCI + if (smc->hw.wdog_used) { + outpw(ADDR(B2_WDOG_CRTL),TIM_START) ; /* Start timer. */ + } +#endif + +#endif /* DEBUG */ +} + +static void smt_stop_watchdog(struct s_smc *smc) +{ + SK_UNUSED(smc) ; /* Make LINT happy. */ +#ifndef DEBUG + +#ifdef PCI + if (smc->hw.wdog_used) { + outpw(ADDR(B2_WDOG_CRTL),TIM_STOP) ; /* Stop timer. */ + } +#endif + +#endif /* DEBUG */ +} + +#ifdef PCI + +void mac_do_pci_fix(struct s_smc *smc) +{ + SK_UNUSED(smc) ; +} +#endif /* PCI */ + diff --git a/kernel/drivers/net/fddi/skfp/ecm.c b/kernel/drivers/net/fddi/skfp/ecm.c new file mode 100644 index 000000000..47d922cb3 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/ecm.c @@ -0,0 +1,536 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + SMT ECM + Entity Coordination Management + Hardware independent state machine +*/ + +/* + * Hardware independent state machine implemantation + * The following external SMT functions are referenced : + * + * queue_event() + * smt_timer_start() + * smt_timer_stop() + * + * The following external HW dependent functions are referenced : + * sm_pm_bypass_req() + * sm_pm_ls_latch() + * sm_pm_get_ls() + * + * The following HW dependent events are required : + * NONE + * + */ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" + +#define KERNEL +#include "h/smtstate.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)ecm.c 2.7 99/08/05 (C) SK " ; +#endif + +/* + * FSM Macros + */ +#define AFLAG 0x10 +#define GO_STATE(x) (smc->mib.fddiSMTECMState = (x)|AFLAG) +#define ACTIONS_DONE() (smc->mib.fddiSMTECMState &= ~AFLAG) +#define ACTIONS(x) (x|AFLAG) + +#define EC0_OUT 0 /* not inserted */ +#define EC1_IN 1 /* inserted */ +#define EC2_TRACE 2 /* tracing */ +#define EC3_LEAVE 3 /* leaving the ring */ +#define EC4_PATH_TEST 4 /* performing path test */ +#define EC5_INSERT 5 /* bypass being turned on */ +#define EC6_CHECK 6 /* checking bypass */ +#define EC7_DEINSERT 7 /* bypass being turnde off */ + +#ifdef DEBUG +/* + * symbolic state names + */ +static const char * const ecm_states[] = { + "EC0_OUT","EC1_IN","EC2_TRACE","EC3_LEAVE","EC4_PATH_TEST", + "EC5_INSERT","EC6_CHECK","EC7_DEINSERT" +} ; + +/* + * symbolic event names + */ +static const char * const ecm_events[] = { + "NONE","EC_CONNECT","EC_DISCONNECT","EC_TRACE_PROP","EC_PATH_TEST", + "EC_TIMEOUT_TD","EC_TIMEOUT_TMAX", + "EC_TIMEOUT_IMAX","EC_TIMEOUT_INMAX","EC_TEST_DONE" +} ; +#endif + +/* + * all Globals are defined in smc.h + * struct s_ecm + */ + +/* + * function declarations + */ + +static void ecm_fsm(struct s_smc *smc, int cmd); +static void start_ecm_timer(struct s_smc *smc, u_long value, int event); +static void stop_ecm_timer(struct s_smc *smc); +static void prop_actions(struct s_smc *smc); + +/* + init ECM state machine + clear all ECM vars and flags +*/ +void ecm_init(struct s_smc *smc) +{ + smc->e.path_test = PT_PASSED ; + smc->e.trace_prop = 0 ; + smc->e.sb_flag = 0 ; + smc->mib.fddiSMTECMState = ACTIONS(EC0_OUT) ; + smc->e.ecm_line_state = FALSE ; +} + +/* + ECM state machine + called by dispatcher + + do + display state change + process event + until SM is stable +*/ +void ecm(struct s_smc *smc, int event) +{ + int state ; + + do { + DB_ECM("ECM : state %s%s", + (smc->mib.fddiSMTECMState & AFLAG) ? "ACTIONS " : "", + ecm_states[smc->mib.fddiSMTECMState & ~AFLAG]) ; + DB_ECM(" event %s\n",ecm_events[event],0) ; + state = smc->mib.fddiSMTECMState ; + ecm_fsm(smc,event) ; + event = 0 ; + } while (state != smc->mib.fddiSMTECMState) ; + ecm_state_change(smc,(int)smc->mib.fddiSMTECMState) ; +} + +/* + process ECM event +*/ +static void ecm_fsm(struct s_smc *smc, int cmd) +{ + int ls_a ; /* current line state PHY A */ + int ls_b ; /* current line state PHY B */ + int p ; /* ports */ + + + smc->mib.fddiSMTBypassPresent = sm_pm_bypass_present(smc) ; + if (cmd == EC_CONNECT) + smc->mib.fddiSMTRemoteDisconnectFlag = FALSE ; + + /* For AIX event notification: */ + /* Is a disconnect command remotely issued ? */ + if (cmd == EC_DISCONNECT && + smc->mib.fddiSMTRemoteDisconnectFlag == TRUE) + AIX_EVENT (smc, (u_long) CIO_HARD_FAIL, (u_long) + FDDI_REMOTE_DISCONNECT, smt_get_event_word(smc), + smt_get_error_word(smc) ); + + /*jd 05-Aug-1999 Bug #10419 "Port Disconnect fails at Dup MAc Cond."*/ + if (cmd == EC_CONNECT) { + smc->e.DisconnectFlag = FALSE ; + } + else if (cmd == EC_DISCONNECT) { + smc->e.DisconnectFlag = TRUE ; + } + + switch(smc->mib.fddiSMTECMState) { + case ACTIONS(EC0_OUT) : + /* + * We do not perform a path test + */ + smc->e.path_test = PT_PASSED ; + smc->e.ecm_line_state = FALSE ; + stop_ecm_timer(smc) ; + ACTIONS_DONE() ; + break ; + case EC0_OUT: + /*EC01*/ + if (cmd == EC_CONNECT && !smc->mib.fddiSMTBypassPresent + && smc->e.path_test==PT_PASSED) { + GO_STATE(EC1_IN) ; + break ; + } + /*EC05*/ + else if (cmd == EC_CONNECT && (smc->e.path_test==PT_PASSED) && + smc->mib.fddiSMTBypassPresent && + (smc->s.sas == SMT_DAS)) { + GO_STATE(EC5_INSERT) ; + break ; + } + break; + case ACTIONS(EC1_IN) : + stop_ecm_timer(smc) ; + smc->e.trace_prop = 0 ; + sm_ma_control(smc,MA_TREQ) ; + for (p = 0 ; p < NUMPHYS ; p++) + if (smc->mib.p[p].fddiPORTHardwarePresent) + queue_event(smc,EVENT_PCMA+p,PC_START) ; + ACTIONS_DONE() ; + break ; + case EC1_IN: + /*EC12*/ + if (cmd == EC_TRACE_PROP) { + prop_actions(smc) ; + GO_STATE(EC2_TRACE) ; + break ; + } + /*EC13*/ + else if (cmd == EC_DISCONNECT) { + GO_STATE(EC3_LEAVE) ; + break ; + } + break; + case ACTIONS(EC2_TRACE) : + start_ecm_timer(smc,MIB2US(smc->mib.fddiSMTTrace_MaxExpiration), + EC_TIMEOUT_TMAX) ; + ACTIONS_DONE() ; + break ; + case EC2_TRACE : + /*EC22*/ + if (cmd == EC_TRACE_PROP) { + prop_actions(smc) ; + GO_STATE(EC2_TRACE) ; + break ; + } + /*EC23a*/ + else if (cmd == EC_DISCONNECT) { + smc->e.path_test = PT_EXITING ; + GO_STATE(EC3_LEAVE) ; + break ; + } + /*EC23b*/ + else if (smc->e.path_test == PT_PENDING) { + GO_STATE(EC3_LEAVE) ; + break ; + } + /*EC23c*/ + else if (cmd == EC_TIMEOUT_TMAX) { + /* Trace_Max is expired */ + /* -> send AIX_EVENT */ + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, + (u_long) FDDI_SMT_ERROR, (u_long) + FDDI_TRACE_MAX, smt_get_error_word(smc)); + smc->e.path_test = PT_PENDING ; + GO_STATE(EC3_LEAVE) ; + break ; + } + break ; + case ACTIONS(EC3_LEAVE) : + start_ecm_timer(smc,smc->s.ecm_td_min,EC_TIMEOUT_TD) ; + for (p = 0 ; p < NUMPHYS ; p++) + queue_event(smc,EVENT_PCMA+p,PC_STOP) ; + ACTIONS_DONE() ; + break ; + case EC3_LEAVE: + /*EC30*/ + if (cmd == EC_TIMEOUT_TD && !smc->mib.fddiSMTBypassPresent && + (smc->e.path_test != PT_PENDING)) { + GO_STATE(EC0_OUT) ; + break ; + } + /*EC34*/ + else if (cmd == EC_TIMEOUT_TD && + (smc->e.path_test == PT_PENDING)) { + GO_STATE(EC4_PATH_TEST) ; + break ; + } + /*EC31*/ + else if (cmd == EC_CONNECT && smc->e.path_test == PT_PASSED) { + GO_STATE(EC1_IN) ; + break ; + } + /*EC33*/ + else if (cmd == EC_DISCONNECT && + smc->e.path_test == PT_PENDING) { + smc->e.path_test = PT_EXITING ; + /* + * stay in state - state will be left via timeout + */ + } + /*EC37*/ + else if (cmd == EC_TIMEOUT_TD && + smc->mib.fddiSMTBypassPresent && + smc->e.path_test != PT_PENDING) { + GO_STATE(EC7_DEINSERT) ; + break ; + } + break ; + case ACTIONS(EC4_PATH_TEST) : + stop_ecm_timer(smc) ; + smc->e.path_test = PT_TESTING ; + start_ecm_timer(smc,smc->s.ecm_test_done,EC_TEST_DONE) ; + /* now perform path test ... just a simulation */ + ACTIONS_DONE() ; + break ; + case EC4_PATH_TEST : + /* path test done delay */ + if (cmd == EC_TEST_DONE) + smc->e.path_test = PT_PASSED ; + + if (smc->e.path_test == PT_FAILED) + RS_SET(smc,RS_PATHTEST) ; + + /*EC40a*/ + if (smc->e.path_test == PT_FAILED && + !smc->mib.fddiSMTBypassPresent) { + GO_STATE(EC0_OUT) ; + break ; + } + /*EC40b*/ + else if (cmd == EC_DISCONNECT && + !smc->mib.fddiSMTBypassPresent) { + GO_STATE(EC0_OUT) ; + break ; + } + /*EC41*/ + else if (smc->e.path_test == PT_PASSED) { + GO_STATE(EC1_IN) ; + break ; + } + /*EC47a*/ + else if (smc->e.path_test == PT_FAILED && + smc->mib.fddiSMTBypassPresent) { + GO_STATE(EC7_DEINSERT) ; + break ; + } + /*EC47b*/ + else if (cmd == EC_DISCONNECT && + smc->mib.fddiSMTBypassPresent) { + GO_STATE(EC7_DEINSERT) ; + break ; + } + break ; + case ACTIONS(EC5_INSERT) : + sm_pm_bypass_req(smc,BP_INSERT); + start_ecm_timer(smc,smc->s.ecm_in_max,EC_TIMEOUT_INMAX) ; + ACTIONS_DONE() ; + break ; + case EC5_INSERT : + /*EC56*/ + if (cmd == EC_TIMEOUT_INMAX) { + GO_STATE(EC6_CHECK) ; + break ; + } + /*EC57*/ + else if (cmd == EC_DISCONNECT) { + GO_STATE(EC7_DEINSERT) ; + break ; + } + break ; + case ACTIONS(EC6_CHECK) : + /* + * in EC6_CHECK, we *POLL* the line state ! + * check whether both bypass switches have switched. + */ + start_ecm_timer(smc,smc->s.ecm_check_poll,0) ; + smc->e.ecm_line_state = TRUE ; /* flag to pcm: report Q/HLS */ + (void) sm_pm_ls_latch(smc,PA,1) ; /* enable line state latch */ + (void) sm_pm_ls_latch(smc,PB,1) ; /* enable line state latch */ + ACTIONS_DONE() ; + break ; + case EC6_CHECK : + ls_a = sm_pm_get_ls(smc,PA) ; + ls_b = sm_pm_get_ls(smc,PB) ; + + /*EC61*/ + if (((ls_a == PC_QLS) || (ls_a == PC_HLS)) && + ((ls_b == PC_QLS) || (ls_b == PC_HLS)) ) { + smc->e.sb_flag = FALSE ; + smc->e.ecm_line_state = FALSE ; + GO_STATE(EC1_IN) ; + break ; + } + /*EC66*/ + else if (!smc->e.sb_flag && + (((ls_a == PC_ILS) && (ls_b == PC_QLS)) || + ((ls_a == PC_QLS) && (ls_b == PC_ILS)))){ + smc->e.sb_flag = TRUE ; + DB_ECMN(1,"ECM : EC6_CHECK - stuck bypass\n",0,0) ; + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, (u_long) + FDDI_SMT_ERROR, (u_long) FDDI_BYPASS_STUCK, + smt_get_error_word(smc)); + } + /*EC67*/ + else if (cmd == EC_DISCONNECT) { + smc->e.ecm_line_state = FALSE ; + GO_STATE(EC7_DEINSERT) ; + break ; + } + else { + /* + * restart poll + */ + start_ecm_timer(smc,smc->s.ecm_check_poll,0) ; + } + break ; + case ACTIONS(EC7_DEINSERT) : + sm_pm_bypass_req(smc,BP_DEINSERT); + start_ecm_timer(smc,smc->s.ecm_i_max,EC_TIMEOUT_IMAX) ; + ACTIONS_DONE() ; + break ; + case EC7_DEINSERT: + /*EC70*/ + if (cmd == EC_TIMEOUT_IMAX) { + GO_STATE(EC0_OUT) ; + break ; + } + /*EC75*/ + else if (cmd == EC_CONNECT && smc->e.path_test == PT_PASSED) { + GO_STATE(EC5_INSERT) ; + break ; + } + break; + default: + SMT_PANIC(smc,SMT_E0107, SMT_E0107_MSG) ; + break; + } +} + +#ifndef CONCENTRATOR +/* + * trace propagation actions for SAS & DAS + */ +static void prop_actions(struct s_smc *smc) +{ + int port_in = 0 ; + int port_out = 0 ; + + RS_SET(smc,RS_EVENT) ; + switch (smc->s.sas) { + case SMT_SAS : + port_in = port_out = pcm_get_s_port(smc) ; + break ; + case SMT_DAS : + port_in = cfm_get_mac_input(smc) ; /* PA or PB */ + port_out = cfm_get_mac_output(smc) ; /* PA or PB */ + break ; + case SMT_NAC : + SMT_PANIC(smc,SMT_E0108, SMT_E0108_MSG) ; + return ; + } + + DB_ECM("ECM : prop_actions - trace_prop %d\n", smc->e.trace_prop,0) ; + DB_ECM("ECM : prop_actions - in %d out %d\n", port_in,port_out) ; + + if (smc->e.trace_prop & ENTITY_BIT(ENTITY_MAC)) { + /* trace initiatior */ + DB_ECM("ECM : initiate TRACE on PHY %c\n",'A'+port_in-PA,0) ; + queue_event(smc,EVENT_PCM+port_in,PC_TRACE) ; + } + else if ((smc->e.trace_prop & ENTITY_BIT(ENTITY_PHY(PA))) && + port_out != PA) { + /* trace propagate upstream */ + DB_ECM("ECM : propagate TRACE on PHY B\n",0,0) ; + queue_event(smc,EVENT_PCMB,PC_TRACE) ; + } + else if ((smc->e.trace_prop & ENTITY_BIT(ENTITY_PHY(PB))) && + port_out != PB) { + /* trace propagate upstream */ + DB_ECM("ECM : propagate TRACE on PHY A\n",0,0) ; + queue_event(smc,EVENT_PCMA,PC_TRACE) ; + } + else { + /* signal trace termination */ + DB_ECM("ECM : TRACE terminated\n",0,0) ; + smc->e.path_test = PT_PENDING ; + } + smc->e.trace_prop = 0 ; +} +#else +/* + * trace propagation actions for Concentrator + */ +static void prop_actions(struct s_smc *smc) +{ + int initiator ; + int upstream ; + int p ; + + RS_SET(smc,RS_EVENT) ; + while (smc->e.trace_prop) { + DB_ECM("ECM : prop_actions - trace_prop %d\n", + smc->e.trace_prop,0) ; + + if (smc->e.trace_prop & ENTITY_BIT(ENTITY_MAC)) { + initiator = ENTITY_MAC ; + smc->e.trace_prop &= ~ENTITY_BIT(ENTITY_MAC) ; + DB_ECM("ECM: MAC initiates trace\n",0,0) ; + } + else { + for (p = NUMPHYS-1 ; p >= 0 ; p--) { + if (smc->e.trace_prop & + ENTITY_BIT(ENTITY_PHY(p))) + break ; + } + initiator = ENTITY_PHY(p) ; + smc->e.trace_prop &= ~ENTITY_BIT(ENTITY_PHY(p)) ; + } + upstream = cem_get_upstream(smc,initiator) ; + + if (upstream == ENTITY_MAC) { + /* signal trace termination */ + DB_ECM("ECM : TRACE terminated\n",0,0) ; + smc->e.path_test = PT_PENDING ; + } + else { + /* trace propagate upstream */ + DB_ECM("ECM : propagate TRACE on PHY %d\n",upstream,0) ; + queue_event(smc,EVENT_PCM+upstream,PC_TRACE) ; + } + } +} +#endif + + +/* + * SMT timer interface + * start ECM timer + */ +static void start_ecm_timer(struct s_smc *smc, u_long value, int event) +{ + smt_timer_start(smc,&smc->e.ecm_timer,value,EV_TOKEN(EVENT_ECM,event)); +} + +/* + * SMT timer interface + * stop ECM timer + */ +static void stop_ecm_timer(struct s_smc *smc) +{ + if (smc->e.ecm_timer.tm_active) + smt_timer_stop(smc,&smc->e.ecm_timer) ; +} diff --git a/kernel/drivers/net/fddi/skfp/ess.c b/kernel/drivers/net/fddi/skfp/ess.c new file mode 100644 index 000000000..2fc5987b4 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/ess.c @@ -0,0 +1,720 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * ******************************************************************* + * This SBA code implements the Synchronous Bandwidth Allocation + * functions described in the "FDDI Synchronous Forum Implementer's + * Agreement" dated December 1th, 1993. + * ******************************************************************* + * + * PURPOSE: The purpose of this function is to control + * synchronous allocations on a single FDDI segment. + * Allocations are limited to the primary FDDI ring. + * The SBM provides recovery mechanisms to recover + * unused bandwidth also resolves T_Neg and + * reconfiguration changes. Many of the SBM state + * machine inputs are sourced by the underlying + * FDDI sub-system supporting the SBA application. + * + * ******************************************************************* + */ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/smt_p.h" + + +#ifndef SLIM_SMT + +#ifdef ESS + +#ifndef lint +static const char ID_sccs[] = "@(#)ess.c 1.10 96/02/23 (C) SK" ; +#define LINT_USE(x) +#else +#define LINT_USE(x) (x)=(x) +#endif +#define MS2BCLK(x) ((x)*12500L) + +/* + ------------------------------------------------------------- + LOCAL VARIABLES: + ------------------------------------------------------------- +*/ + +static const u_short plist_raf_alc_res[] = { SMT_P0012, SMT_P320B, SMT_P320F, + SMT_P3210, SMT_P0019, SMT_P001A, + SMT_P001D, 0 } ; + +static const u_short plist_raf_chg_req[] = { SMT_P320B, SMT_P320F, SMT_P3210, + SMT_P001A, 0 } ; + +static const struct fddi_addr smt_sba_da = {{0x80,0x01,0x43,0x00,0x80,0x0C}} ; +static const struct fddi_addr null_addr = {{0,0,0,0,0,0}} ; + +/* + ------------------------------------------------------------- + GLOBAL VARIABLES: + ------------------------------------------------------------- +*/ + + +/* + ------------------------------------------------------------- + LOCAL FUNCTIONS: + ------------------------------------------------------------- +*/ + +static void ess_send_response(struct s_smc *smc, struct smt_header *sm, + int sba_cmd); +static void ess_config_fifo(struct s_smc *smc); +static void ess_send_alc_req(struct s_smc *smc); +static void ess_send_frame(struct s_smc *smc, SMbuf *mb); + +/* + ------------------------------------------------------------- + EXTERNAL FUNCTIONS: + ------------------------------------------------------------- +*/ + +/* + ------------------------------------------------------------- + PUBLIC FUNCTIONS: + ------------------------------------------------------------- +*/ + +void ess_timer_poll(struct s_smc *smc); +void ess_para_change(struct s_smc *smc); +int ess_raf_received_pack(struct s_smc *smc, SMbuf *mb, struct smt_header *sm, + int fs); +static int process_bw_alloc(struct s_smc *smc, long int payload, long int overhead); + + +/* + * -------------------------------------------------------------------------- + * End Station Support (ESS) + * -------------------------------------------------------------------------- + */ + +/* + * evaluate the RAF frame + */ +int ess_raf_received_pack(struct s_smc *smc, SMbuf *mb, struct smt_header *sm, + int fs) +{ + void *p ; /* universal pointer */ + struct smt_p_0016 *cmd ; /* para: command for the ESS */ + SMbuf *db ; + u_long msg_res_type ; /* recource type */ + u_long payload, overhead ; + int local ; + int i ; + + /* + * Message Processing Code + */ + local = ((fs & L_INDICATOR) != 0) ; + + /* + * get the resource type + */ + if (!(p = (void *) sm_to_para(smc,sm,SMT_P0015))) { + DB_ESS("ESS: RAF frame error, parameter type not found\n",0,0) ; + return fs; + } + msg_res_type = ((struct smt_p_0015 *)p)->res_type ; + + /* + * get the pointer to the ESS command + */ + if (!(cmd = (struct smt_p_0016 *) sm_to_para(smc,sm,SMT_P0016))) { + /* + * error in frame: para ESS command was not found + */ + DB_ESS("ESS: RAF frame error, parameter command not found\n",0,0); + return fs; + } + + DB_ESSN(2,"fc %x ft %x\n",sm->smt_class,sm->smt_type) ; + DB_ESSN(2,"ver %x tran %lx\n",sm->smt_version,sm->smt_tid) ; + DB_ESSN(2,"stn_id %s\n",addr_to_string(&sm->smt_source),0) ; + + DB_ESSN(2,"infolen %x res %x\n",sm->smt_len, msg_res_type) ; + DB_ESSN(2,"sbacmd %x\n",cmd->sba_cmd,0) ; + + /* + * evaluate the ESS command + */ + switch (cmd->sba_cmd) { + + /* + * Process an ESS Allocation Request + */ + case REQUEST_ALLOCATION : + /* + * check for an RAF Request (Allocation Request) + */ + if (sm->smt_type == SMT_REQUEST) { + /* + * process the Allocation request only if the frame is + * local and no static allocation is used + */ + if (!local || smc->mib.fddiESSPayload) + return fs; + + p = (void *) sm_to_para(smc,sm,SMT_P0019) ; + for (i = 0; i < 5; i++) { + if (((struct smt_p_0019 *)p)->alloc_addr.a[i]) { + return fs; + } + } + + /* + * Note: The Application should send a LAN_LOC_FRAME. + * The ESS do not send the Frame to the network! + */ + smc->ess.alloc_trans_id = sm->smt_tid ; + DB_ESS("ESS: save Alloc Req Trans ID %lx\n",sm->smt_tid,0); + p = (void *) sm_to_para(smc,sm,SMT_P320F) ; + ((struct smt_p_320f *)p)->mib_payload = + smc->mib.a[PATH0].fddiPATHSbaPayload ; + p = (void *) sm_to_para(smc,sm,SMT_P3210) ; + ((struct smt_p_3210 *)p)->mib_overhead = + smc->mib.a[PATH0].fddiPATHSbaOverhead ; + sm->smt_dest = smt_sba_da ; + + if (smc->ess.local_sba_active) + return fs | I_INDICATOR; + + if (!(db = smt_get_mbuf(smc))) + return fs; + + db->sm_len = mb->sm_len ; + db->sm_off = mb->sm_off ; + memcpy(((char *)(db->sm_data+db->sm_off)),(char *)sm, + (int)db->sm_len) ; + dump_smt(smc, + (struct smt_header *)(db->sm_data+db->sm_off), + "RAF") ; + smt_send_frame(smc,db,FC_SMT_INFO,0) ; + return fs; + } + + /* + * The RAF frame is an Allocation Response ! + * check the parameters + */ + if (smt_check_para(smc,sm,plist_raf_alc_res)) { + DB_ESS("ESS: RAF with para problem, ignoring\n",0,0) ; + return fs; + } + + /* + * VERIFY THE FRAME IS WELL BUILT: + * + * 1. path index = primary ring only + * 2. resource type = sync bw only + * 3. trans action id = alloc_trans_id + * 4. reason code = success + * + * If any are violated, discard the RAF frame + */ + if ((((struct smt_p_320b *)sm_to_para(smc,sm,SMT_P320B))->path_index + != PRIMARY_RING) || + (msg_res_type != SYNC_BW) || + (((struct smt_p_reason *)sm_to_para(smc,sm,SMT_P0012))->rdf_reason + != SMT_RDF_SUCCESS) || + (sm->smt_tid != smc->ess.alloc_trans_id)) { + + DB_ESS("ESS: Allocation Response not accepted\n",0,0) ; + return fs; + } + + /* + * Extract message parameters + */ + p = (void *) sm_to_para(smc,sm,SMT_P320F) ; + if (!p) { + printk(KERN_ERR "ESS: sm_to_para failed"); + return fs; + } + payload = ((struct smt_p_320f *)p)->mib_payload ; + p = (void *) sm_to_para(smc,sm,SMT_P3210) ; + if (!p) { + printk(KERN_ERR "ESS: sm_to_para failed"); + return fs; + } + overhead = ((struct smt_p_3210 *)p)->mib_overhead ; + + DB_ESSN(2,"payload= %lx overhead= %lx\n",payload,overhead) ; + + /* + * process the bandwidth allocation + */ + (void)process_bw_alloc(smc,(long)payload,(long)overhead) ; + + return fs; + /* end of Process Allocation Request */ + + /* + * Process an ESS Change Request + */ + case CHANGE_ALLOCATION : + /* + * except only replies + */ + if (sm->smt_type != SMT_REQUEST) { + DB_ESS("ESS: Do not process Change Responses\n",0,0) ; + return fs; + } + + /* + * check the para for the Change Request + */ + if (smt_check_para(smc,sm,plist_raf_chg_req)) { + DB_ESS("ESS: RAF with para problem, ignoring\n",0,0) ; + return fs; + } + + /* + * Verify the path index and resource + * type are correct. If any of + * these are false, don't process this + * change request frame. + */ + if ((((struct smt_p_320b *)sm_to_para(smc,sm,SMT_P320B))->path_index + != PRIMARY_RING) || (msg_res_type != SYNC_BW)) { + DB_ESS("ESS: RAF frame with para problem, ignoring\n",0,0) ; + return fs; + } + + /* + * Extract message queue parameters + */ + p = (void *) sm_to_para(smc,sm,SMT_P320F) ; + payload = ((struct smt_p_320f *)p)->mib_payload ; + p = (void *) sm_to_para(smc,sm,SMT_P3210) ; + overhead = ((struct smt_p_3210 *)p)->mib_overhead ; + + DB_ESSN(2,"ESS: Change Request from %s\n", + addr_to_string(&sm->smt_source),0) ; + DB_ESSN(2,"payload= %lx overhead= %lx\n",payload,overhead) ; + + /* + * process the bandwidth allocation + */ + if(!process_bw_alloc(smc,(long)payload,(long)overhead)) + return fs; + + /* + * send an RAF Change Reply + */ + ess_send_response(smc,sm,CHANGE_ALLOCATION) ; + + return fs; + /* end of Process Change Request */ + + /* + * Process Report Response + */ + case REPORT_ALLOCATION : + /* + * except only requests + */ + if (sm->smt_type != SMT_REQUEST) { + DB_ESS("ESS: Do not process a Report Reply\n",0,0) ; + return fs; + } + + DB_ESSN(2,"ESS: Report Request from %s\n", + addr_to_string(&(sm->smt_source)),0) ; + + /* + * verify that the resource type is sync bw only + */ + if (msg_res_type != SYNC_BW) { + DB_ESS("ESS: ignoring RAF with para problem\n",0,0) ; + return fs; + } + + /* + * send an RAF Change Reply + */ + ess_send_response(smc,sm,REPORT_ALLOCATION) ; + + return fs; + /* end of Process Report Request */ + + default: + /* + * error in frame + */ + DB_ESS("ESS: ignoring RAF with bad sba_cmd\n",0,0) ; + break ; + } + + return fs; +} + +/* + * determines the synchronous bandwidth, set the TSYNC register and the + * mib variables SBAPayload, SBAOverhead and fddiMACT-NEG. + */ +static int process_bw_alloc(struct s_smc *smc, long int payload, long int overhead) +{ + /* + * determine the synchronous bandwidth (sync_bw) in bytes per T-NEG, + * if the payload is greater than zero. + * For the SBAPayload and the SBAOverhead we have the following + * unite quations + * _ _ + * | bytes | + * SBAPayload = | 8000 ------ | + * | s | + * - - + * _ _ + * | bytes | + * SBAOverhead = | ------ | + * | T-NEG | + * - - + * + * T-NEG is described by the equation: + * + * (-) fddiMACT-NEG + * T-NEG = ------------------- + * 12500000 1/s + * + * The number of bytes we are able to send is the payload + * plus the overhead. + * + * bytes T-NEG SBAPayload 8000 bytes/s + * sync_bw = SBAOverhead ------ + ----------------------------- + * T-NEG T-NEG + * + * + * 1 + * sync_bw = SBAOverhead + ---- (-)fddiMACT-NEG * SBAPayload + * 1562 + * + */ + + /* + * set the mib attributes fddiPATHSbaOverhead, fddiPATHSbaPayload + */ +/* if (smt_set_obj(smc,SMT_P320F,payload,S_SET)) { + DB_ESS("ESS: SMT does not accept the payload value\n",0,0) ; + return FALSE; + } + if (smt_set_obj(smc,SMT_P3210,overhead,S_SET)) { + DB_ESS("ESS: SMT does not accept the overhead value\n",0,0) ; + return FALSE; + } */ + + /* premliminary */ + if (payload > MAX_PAYLOAD || overhead > 5000) { + DB_ESS("ESS: payload / overhead not accepted\n",0,0) ; + return FALSE; + } + + /* + * start the iterative allocation process if the payload or the overhead + * are smaller than the parsed values + */ + if (smc->mib.fddiESSPayload && + ((u_long)payload != smc->mib.fddiESSPayload || + (u_long)overhead != smc->mib.fddiESSOverhead)) { + smc->ess.raf_act_timer_poll = TRUE ; + smc->ess.timer_count = 0 ; + } + + /* + * evulate the Payload + */ + if (payload) { + DB_ESSN(2,"ESS: turn SMT_ST_SYNC_SERVICE bit on\n",0,0) ; + smc->ess.sync_bw_available = TRUE ; + + smc->ess.sync_bw = overhead - + (long)smc->mib.m[MAC0].fddiMACT_Neg * + payload / 1562 ; + } + else { + DB_ESSN(2,"ESS: turn SMT_ST_SYNC_SERVICE bit off\n",0,0) ; + smc->ess.sync_bw_available = FALSE ; + smc->ess.sync_bw = 0 ; + overhead = 0 ; + } + + smc->mib.a[PATH0].fddiPATHSbaPayload = payload ; + smc->mib.a[PATH0].fddiPATHSbaOverhead = overhead ; + + + DB_ESSN(2,"tsync = %lx\n",smc->ess.sync_bw,0) ; + + ess_config_fifo(smc) ; + set_formac_tsync(smc,smc->ess.sync_bw) ; + return TRUE; +} + +static void ess_send_response(struct s_smc *smc, struct smt_header *sm, + int sba_cmd) +{ + struct smt_sba_chg *chg ; + SMbuf *mb ; + void *p ; + + /* + * get and initialize the response frame + */ + if (sba_cmd == CHANGE_ALLOCATION) { + if (!(mb=smt_build_frame(smc,SMT_RAF,SMT_REPLY, + sizeof(struct smt_sba_chg)))) + return ; + } + else { + if (!(mb=smt_build_frame(smc,SMT_RAF,SMT_REPLY, + sizeof(struct smt_sba_rep_res)))) + return ; + } + + chg = smtod(mb,struct smt_sba_chg *) ; + chg->smt.smt_tid = sm->smt_tid ; + chg->smt.smt_dest = sm->smt_source ; + + /* set P15 */ + chg->s_type.para.p_type = SMT_P0015 ; + chg->s_type.para.p_len = sizeof(struct smt_p_0015) - PARA_LEN ; + chg->s_type.res_type = SYNC_BW ; + + /* set P16 */ + chg->cmd.para.p_type = SMT_P0016 ; + chg->cmd.para.p_len = sizeof(struct smt_p_0016) - PARA_LEN ; + chg->cmd.sba_cmd = sba_cmd ; + + /* set P320B */ + chg->path.para.p_type = SMT_P320B ; + chg->path.para.p_len = sizeof(struct smt_p_320b) - PARA_LEN ; + chg->path.mib_index = SBAPATHINDEX ; + chg->path.path_pad = 0; + chg->path.path_index = PRIMARY_RING ; + + /* set P320F */ + chg->payload.para.p_type = SMT_P320F ; + chg->payload.para.p_len = sizeof(struct smt_p_320f) - PARA_LEN ; + chg->payload.mib_index = SBAPATHINDEX ; + chg->payload.mib_payload = smc->mib.a[PATH0].fddiPATHSbaPayload ; + + /* set P3210 */ + chg->overhead.para.p_type = SMT_P3210 ; + chg->overhead.para.p_len = sizeof(struct smt_p_3210) - PARA_LEN ; + chg->overhead.mib_index = SBAPATHINDEX ; + chg->overhead.mib_overhead = smc->mib.a[PATH0].fddiPATHSbaOverhead ; + + if (sba_cmd == CHANGE_ALLOCATION) { + /* set P1A */ + chg->cat.para.p_type = SMT_P001A ; + chg->cat.para.p_len = sizeof(struct smt_p_001a) - PARA_LEN ; + p = (void *) sm_to_para(smc,sm,SMT_P001A) ; + chg->cat.category = ((struct smt_p_001a *)p)->category ; + } + dump_smt(smc,(struct smt_header *)chg,"RAF") ; + ess_send_frame(smc,mb) ; +} + +void ess_timer_poll(struct s_smc *smc) +{ + if (!smc->ess.raf_act_timer_poll) + return ; + + DB_ESSN(2,"ESS: timer_poll\n",0,0) ; + + smc->ess.timer_count++ ; + if (smc->ess.timer_count == 10) { + smc->ess.timer_count = 0 ; + ess_send_alc_req(smc) ; + } +} + +static void ess_send_alc_req(struct s_smc *smc) +{ + struct smt_sba_alc_req *req ; + SMbuf *mb ; + + /* + * send never allocation request where the requested payload and + * overhead is zero or deallocate bandwidth when no bandwidth is + * parsed + */ + if (!smc->mib.fddiESSPayload) { + smc->mib.fddiESSOverhead = 0 ; + } + else { + if (!smc->mib.fddiESSOverhead) + smc->mib.fddiESSOverhead = DEFAULT_OV ; + } + + if (smc->mib.fddiESSOverhead == + smc->mib.a[PATH0].fddiPATHSbaOverhead && + smc->mib.fddiESSPayload == + smc->mib.a[PATH0].fddiPATHSbaPayload){ + smc->ess.raf_act_timer_poll = FALSE ; + smc->ess.timer_count = 7 ; /* next RAF alc req after 3 s */ + return ; + } + + /* + * get and initialize the response frame + */ + if (!(mb=smt_build_frame(smc,SMT_RAF,SMT_REQUEST, + sizeof(struct smt_sba_alc_req)))) + return ; + req = smtod(mb,struct smt_sba_alc_req *) ; + req->smt.smt_tid = smc->ess.alloc_trans_id = smt_get_tid(smc) ; + req->smt.smt_dest = smt_sba_da ; + + /* set P15 */ + req->s_type.para.p_type = SMT_P0015 ; + req->s_type.para.p_len = sizeof(struct smt_p_0015) - PARA_LEN ; + req->s_type.res_type = SYNC_BW ; + + /* set P16 */ + req->cmd.para.p_type = SMT_P0016 ; + req->cmd.para.p_len = sizeof(struct smt_p_0016) - PARA_LEN ; + req->cmd.sba_cmd = REQUEST_ALLOCATION ; + + /* + * set the parameter type and parameter length of all used + * parameters + */ + + /* set P320B */ + req->path.para.p_type = SMT_P320B ; + req->path.para.p_len = sizeof(struct smt_p_320b) - PARA_LEN ; + req->path.mib_index = SBAPATHINDEX ; + req->path.path_pad = 0; + req->path.path_index = PRIMARY_RING ; + + /* set P0017 */ + req->pl_req.para.p_type = SMT_P0017 ; + req->pl_req.para.p_len = sizeof(struct smt_p_0017) - PARA_LEN ; + req->pl_req.sba_pl_req = smc->mib.fddiESSPayload - + smc->mib.a[PATH0].fddiPATHSbaPayload ; + + /* set P0018 */ + req->ov_req.para.p_type = SMT_P0018 ; + req->ov_req.para.p_len = sizeof(struct smt_p_0018) - PARA_LEN ; + req->ov_req.sba_ov_req = smc->mib.fddiESSOverhead - + smc->mib.a[PATH0].fddiPATHSbaOverhead ; + + /* set P320F */ + req->payload.para.p_type = SMT_P320F ; + req->payload.para.p_len = sizeof(struct smt_p_320f) - PARA_LEN ; + req->payload.mib_index = SBAPATHINDEX ; + req->payload.mib_payload = smc->mib.a[PATH0].fddiPATHSbaPayload ; + + /* set P3210 */ + req->overhead.para.p_type = SMT_P3210 ; + req->overhead.para.p_len = sizeof(struct smt_p_3210) - PARA_LEN ; + req->overhead.mib_index = SBAPATHINDEX ; + req->overhead.mib_overhead = smc->mib.a[PATH0].fddiPATHSbaOverhead ; + + /* set P19 */ + req->a_addr.para.p_type = SMT_P0019 ; + req->a_addr.para.p_len = sizeof(struct smt_p_0019) - PARA_LEN ; + req->a_addr.sba_pad = 0; + req->a_addr.alloc_addr = null_addr ; + + /* set P1A */ + req->cat.para.p_type = SMT_P001A ; + req->cat.para.p_len = sizeof(struct smt_p_001a) - PARA_LEN ; + req->cat.category = smc->mib.fddiESSCategory ; + + /* set P1B */ + req->tneg.para.p_type = SMT_P001B ; + req->tneg.para.p_len = sizeof(struct smt_p_001b) - PARA_LEN ; + req->tneg.max_t_neg = smc->mib.fddiESSMaxTNeg ; + + /* set P1C */ + req->segm.para.p_type = SMT_P001C ; + req->segm.para.p_len = sizeof(struct smt_p_001c) - PARA_LEN ; + req->segm.min_seg_siz = smc->mib.fddiESSMinSegmentSize ; + + dump_smt(smc,(struct smt_header *)req,"RAF") ; + ess_send_frame(smc,mb) ; +} + +static void ess_send_frame(struct s_smc *smc, SMbuf *mb) +{ + /* + * check if the frame must be send to the own ESS + */ + if (smc->ess.local_sba_active) { + /* + * Send the Change Reply to the local SBA + */ + DB_ESS("ESS:Send to the local SBA\n",0,0) ; + if (!smc->ess.sba_reply_pend) + smc->ess.sba_reply_pend = mb ; + else { + DB_ESS("Frame is lost - another frame was pending\n",0,0); + smt_free_mbuf(smc,mb) ; + } + } + else { + /* + * Send the SBA RAF Change Reply to the network + */ + DB_ESS("ESS:Send to the network\n",0,0) ; + smt_send_frame(smc,mb,FC_SMT_INFO,0) ; + } +} + +void ess_para_change(struct s_smc *smc) +{ + (void)process_bw_alloc(smc,(long)smc->mib.a[PATH0].fddiPATHSbaPayload, + (long)smc->mib.a[PATH0].fddiPATHSbaOverhead) ; +} + +static void ess_config_fifo(struct s_smc *smc) +{ + /* + * if nothing to do exit + */ + if (smc->mib.a[PATH0].fddiPATHSbaPayload) { + if (smc->hw.fp.fifo.fifo_config_mode & SYNC_TRAFFIC_ON && + (smc->hw.fp.fifo.fifo_config_mode&SEND_ASYNC_AS_SYNC) == + smc->mib.fddiESSSynchTxMode) { + return ; + } + } + else { + if (!(smc->hw.fp.fifo.fifo_config_mode & SYNC_TRAFFIC_ON)) { + return ; + } + } + + /* + * split up the FIFO and reinitialize the queues + */ + formac_reinit_tx(smc) ; +} + +#endif /* ESS */ + +#endif /* no SLIM_SMT */ + diff --git a/kernel/drivers/net/fddi/skfp/fplustm.c b/kernel/drivers/net/fddi/skfp/fplustm.c new file mode 100644 index 000000000..7d3779ae7 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/fplustm.c @@ -0,0 +1,1492 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * FORMAC+ Driver for tag mode + */ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/supern_2.h" +#include <linux/bitrev.h> +#include <linux/etherdevice.h> + +#ifndef lint +static const char ID_sccs[] = "@(#)fplustm.c 1.32 99/02/23 (C) SK " ; +#endif + +#ifndef UNUSED +#ifdef lint +#define UNUSED(x) (x) = (x) +#else +#define UNUSED(x) +#endif +#endif + +#define FM_ADDRX (FM_ADDET|FM_EXGPA0|FM_EXGPA1) +#define MS2BCLK(x) ((x)*12500L) +#define US2BCLK(x) ((x)*1250L) + +/* + * prototypes for static function + */ +static void build_claim_beacon(struct s_smc *smc, u_long t_request); +static int init_mac(struct s_smc *smc, int all); +static void rtm_init(struct s_smc *smc); +static void smt_split_up_fifo(struct s_smc *smc); + +#if (!defined(NO_SMT_PANIC) || defined(DEBUG)) +static char write_mdr_warning [] = "E350 write_mdr() FM_SNPPND is set\n"; +static char cam_warning [] = "E_SMT_004: CAM still busy\n"; +#endif + +#define DUMMY_READ() smc->hw.mc_dummy = (u_short) inp(ADDR(B0_RAP)) + +#define CHECK_NPP() { unsigned int k = 10000 ;\ + while ((inpw(FM_A(FM_STMCHN)) & FM_SNPPND) && k) k--;\ + if (!k) { \ + SMT_PANIC(smc,SMT_E0130, SMT_E0130_MSG) ; \ + } \ + } + +#define CHECK_CAM() { unsigned int k = 10 ;\ + while (!(inpw(FM_A(FM_AFSTAT)) & FM_DONE) && k) k--;\ + if (!k) { \ + SMT_PANIC(smc,SMT_E0131, SMT_E0131_MSG) ; \ + } \ + } + +const struct fddi_addr fddi_broadcast = {{0xff,0xff,0xff,0xff,0xff,0xff}}; +static const struct fddi_addr null_addr = {{0,0,0,0,0,0}}; +static const struct fddi_addr dbeacon_multi = {{0x01,0x80,0xc2,0x00,0x01,0x00}}; + +static const u_short my_said = 0xffff ; /* short address (n.u.) */ +static const u_short my_sagp = 0xffff ; /* short group address (n.u.) */ + +/* + * define my address + */ +#ifdef USE_CAN_ADDR +#define MA smc->hw.fddi_canon_addr +#else +#define MA smc->hw.fddi_home_addr +#endif + + +/* + * useful interrupt bits + */ +static const int mac_imsk1u = FM_STXABRS | FM_STXABRA0 | FM_SXMTABT ; +static const int mac_imsk1l = FM_SQLCKS | FM_SQLCKA0 | FM_SPCEPDS | FM_SPCEPDA0| + FM_STBURS | FM_STBURA0 ; + + /* delete FM_SRBFL after tests */ +static const int mac_imsk2u = FM_SERRSF | FM_SNFSLD | FM_SRCVOVR | FM_SRBFL | + FM_SMYCLM ; +static const int mac_imsk2l = FM_STRTEXR | FM_SDUPCLM | FM_SFRMCTR | + FM_SERRCTR | FM_SLSTCTR | + FM_STRTEXP | FM_SMULTDA | FM_SRNGOP ; + +static const int mac_imsk3u = FM_SRCVOVR2 | FM_SRBFL2 ; +static const int mac_imsk3l = FM_SRPERRQ2 | FM_SRPERRQ1 ; + +static const int mac_beacon_imsk2u = FM_SOTRBEC | FM_SMYBEC | FM_SBEC | + FM_SLOCLM | FM_SHICLM | FM_SMYCLM | FM_SCLM ; + + +static u_long mac_get_tneg(struct s_smc *smc) +{ + u_long tneg ; + + tneg = (u_long)((long)inpw(FM_A(FM_TNEG))<<5) ; + return (u_long)((tneg + ((inpw(FM_A(FM_TMRS))>>10)&0x1f)) | + 0xffe00000L) ; +} + +void mac_update_counter(struct s_smc *smc) +{ + smc->mib.m[MAC0].fddiMACFrame_Ct = + (smc->mib.m[MAC0].fddiMACFrame_Ct & 0xffff0000L) + + (u_short) inpw(FM_A(FM_FCNTR)) ; + smc->mib.m[MAC0].fddiMACLost_Ct = + (smc->mib.m[MAC0].fddiMACLost_Ct & 0xffff0000L) + + (u_short) inpw(FM_A(FM_LCNTR)) ; + smc->mib.m[MAC0].fddiMACError_Ct = + (smc->mib.m[MAC0].fddiMACError_Ct & 0xffff0000L) + + (u_short) inpw(FM_A(FM_ECNTR)) ; + smc->mib.m[MAC0].fddiMACT_Neg = mac_get_tneg(smc) ; +#ifdef SMT_REAL_TOKEN_CT + /* + * If the token counter is emulated it is updated in smt_event. + */ + TBD +#else + smt_emulate_token_ct( smc, MAC0 ); +#endif +} + +/* + * write long value into buffer memory over memory data register (MDR), + */ +static void write_mdr(struct s_smc *smc, u_long val) +{ + CHECK_NPP() ; + MDRW(val) ; +} + +#if 0 +/* + * read long value from buffer memory over memory data register (MDR), + */ +static u_long read_mdr(struct s_smc *smc, unsigned int addr) +{ + long p ; + CHECK_NPP() ; + MARR(addr) ; + outpw(FM_A(FM_CMDREG1),FM_IRMEMWO) ; + CHECK_NPP() ; /* needed for PCI to prevent from timeing violations */ +/* p = MDRR() ; */ /* bad read values if the workaround */ + /* smc->hw.mc_dummy = *((short volatile far *)(addr)))*/ + /* is used */ + p = (u_long)inpw(FM_A(FM_MDRU))<<16 ; + p += (u_long)inpw(FM_A(FM_MDRL)) ; + return p; +} +#endif + +/* + * clear buffer memory + */ +static void init_ram(struct s_smc *smc) +{ + u_short i ; + + smc->hw.fp.fifo.rbc_ram_start = 0 ; + smc->hw.fp.fifo.rbc_ram_end = + smc->hw.fp.fifo.rbc_ram_start + RBC_MEM_SIZE ; + CHECK_NPP() ; + MARW(smc->hw.fp.fifo.rbc_ram_start) ; + for (i = smc->hw.fp.fifo.rbc_ram_start; + i < (u_short) (smc->hw.fp.fifo.rbc_ram_end-1); i++) + write_mdr(smc,0L) ; + /* Erase the last byte too */ + write_mdr(smc,0L) ; +} + +/* + * set receive FIFO pointer + */ +static void set_recvptr(struct s_smc *smc) +{ + /* + * initialize the pointer for receive queue 1 + */ + outpw(FM_A(FM_RPR1),smc->hw.fp.fifo.rx1_fifo_start) ; /* RPR1 */ + outpw(FM_A(FM_SWPR1),smc->hw.fp.fifo.rx1_fifo_start) ; /* SWPR1 */ + outpw(FM_A(FM_WPR1),smc->hw.fp.fifo.rx1_fifo_start) ; /* WPR1 */ + outpw(FM_A(FM_EARV1),smc->hw.fp.fifo.tx_s_start-1) ; /* EARV1 */ + + /* + * initialize the pointer for receive queue 2 + */ + if (smc->hw.fp.fifo.rx2_fifo_size) { + outpw(FM_A(FM_RPR2),smc->hw.fp.fifo.rx2_fifo_start) ; + outpw(FM_A(FM_SWPR2),smc->hw.fp.fifo.rx2_fifo_start) ; + outpw(FM_A(FM_WPR2),smc->hw.fp.fifo.rx2_fifo_start) ; + outpw(FM_A(FM_EARV2),smc->hw.fp.fifo.rbc_ram_end-1) ; + } + else { + outpw(FM_A(FM_RPR2),smc->hw.fp.fifo.rbc_ram_end-1) ; + outpw(FM_A(FM_SWPR2),smc->hw.fp.fifo.rbc_ram_end-1) ; + outpw(FM_A(FM_WPR2),smc->hw.fp.fifo.rbc_ram_end-1) ; + outpw(FM_A(FM_EARV2),smc->hw.fp.fifo.rbc_ram_end-1) ; + } +} + +/* + * set transmit FIFO pointer + */ +static void set_txptr(struct s_smc *smc) +{ + outpw(FM_A(FM_CMDREG2),FM_IRSTQ) ; /* reset transmit queues */ + + /* + * initialize the pointer for asynchronous transmit queue + */ + outpw(FM_A(FM_RPXA0),smc->hw.fp.fifo.tx_a0_start) ; /* RPXA0 */ + outpw(FM_A(FM_SWPXA0),smc->hw.fp.fifo.tx_a0_start) ; /* SWPXA0 */ + outpw(FM_A(FM_WPXA0),smc->hw.fp.fifo.tx_a0_start) ; /* WPXA0 */ + outpw(FM_A(FM_EAA0),smc->hw.fp.fifo.rx2_fifo_start-1) ; /* EAA0 */ + + /* + * initialize the pointer for synchronous transmit queue + */ + if (smc->hw.fp.fifo.tx_s_size) { + outpw(FM_A(FM_RPXS),smc->hw.fp.fifo.tx_s_start) ; + outpw(FM_A(FM_SWPXS),smc->hw.fp.fifo.tx_s_start) ; + outpw(FM_A(FM_WPXS),smc->hw.fp.fifo.tx_s_start) ; + outpw(FM_A(FM_EAS),smc->hw.fp.fifo.tx_a0_start-1) ; + } + else { + outpw(FM_A(FM_RPXS),smc->hw.fp.fifo.tx_a0_start-1) ; + outpw(FM_A(FM_SWPXS),smc->hw.fp.fifo.tx_a0_start-1) ; + outpw(FM_A(FM_WPXS),smc->hw.fp.fifo.tx_a0_start-1) ; + outpw(FM_A(FM_EAS),smc->hw.fp.fifo.tx_a0_start-1) ; + } +} + +/* + * init memory buffer management registers + */ +static void init_rbc(struct s_smc *smc) +{ + u_short rbc_ram_addr ; + + /* + * set unused pointers or permanent pointers + */ + rbc_ram_addr = smc->hw.fp.fifo.rx2_fifo_start - 1 ; + + outpw(FM_A(FM_RPXA1),rbc_ram_addr) ; /* a1-send pointer */ + outpw(FM_A(FM_WPXA1),rbc_ram_addr) ; + outpw(FM_A(FM_SWPXA1),rbc_ram_addr) ; + outpw(FM_A(FM_EAA1),rbc_ram_addr) ; + + set_recvptr(smc) ; + set_txptr(smc) ; +} + +/* + * init rx pointer + */ +static void init_rx(struct s_smc *smc) +{ + struct s_smt_rx_queue *queue ; + + /* + * init all tx data structures for receive queue 1 + */ + smc->hw.fp.rx[QUEUE_R1] = queue = &smc->hw.fp.rx_q[QUEUE_R1] ; + queue->rx_bmu_ctl = (HW_PTR) ADDR(B0_R1_CSR) ; + queue->rx_bmu_dsc = (HW_PTR) ADDR(B4_R1_DA) ; + + /* + * init all tx data structures for receive queue 2 + */ + smc->hw.fp.rx[QUEUE_R2] = queue = &smc->hw.fp.rx_q[QUEUE_R2] ; + queue->rx_bmu_ctl = (HW_PTR) ADDR(B0_R2_CSR) ; + queue->rx_bmu_dsc = (HW_PTR) ADDR(B4_R2_DA) ; +} + +/* + * set the TSYNC register of the FORMAC to regulate synchronous transmission + */ +void set_formac_tsync(struct s_smc *smc, long sync_bw) +{ + outpw(FM_A(FM_TSYNC),(unsigned int) (((-sync_bw) >> 5) & 0xffff) ) ; +} + +/* + * init all tx data structures + */ +static void init_tx(struct s_smc *smc) +{ + struct s_smt_tx_queue *queue ; + + /* + * init all tx data structures for the synchronous queue + */ + smc->hw.fp.tx[QUEUE_S] = queue = &smc->hw.fp.tx_q[QUEUE_S] ; + queue->tx_bmu_ctl = (HW_PTR) ADDR(B0_XS_CSR) ; + queue->tx_bmu_dsc = (HW_PTR) ADDR(B5_XS_DA) ; + +#ifdef ESS + set_formac_tsync(smc,smc->ess.sync_bw) ; +#endif + + /* + * init all tx data structures for the asynchronous queue 0 + */ + smc->hw.fp.tx[QUEUE_A0] = queue = &smc->hw.fp.tx_q[QUEUE_A0] ; + queue->tx_bmu_ctl = (HW_PTR) ADDR(B0_XA_CSR) ; + queue->tx_bmu_dsc = (HW_PTR) ADDR(B5_XA_DA) ; + + + llc_recover_tx(smc) ; +} + +static void mac_counter_init(struct s_smc *smc) +{ + int i ; + u_long *ec ; + + /* + * clear FORMAC+ frame-, lost- and error counter + */ + outpw(FM_A(FM_FCNTR),0) ; + outpw(FM_A(FM_LCNTR),0) ; + outpw(FM_A(FM_ECNTR),0) ; + /* + * clear internal error counter structure + */ + ec = (u_long *)&smc->hw.fp.err_stats ; + for (i = (sizeof(struct err_st)/sizeof(long)) ; i ; i--) + *ec++ = 0L ; + smc->mib.m[MAC0].fddiMACRingOp_Ct = 0 ; +} + +/* + * set FORMAC address, and t_request + */ +static void set_formac_addr(struct s_smc *smc) +{ + long t_requ = smc->mib.m[MAC0].fddiMACT_Req ; + + outpw(FM_A(FM_SAID),my_said) ; /* set short address */ + outpw(FM_A(FM_LAIL),(unsigned short)((smc->hw.fddi_home_addr.a[4]<<8) + + smc->hw.fddi_home_addr.a[5])) ; + outpw(FM_A(FM_LAIC),(unsigned short)((smc->hw.fddi_home_addr.a[2]<<8) + + smc->hw.fddi_home_addr.a[3])) ; + outpw(FM_A(FM_LAIM),(unsigned short)((smc->hw.fddi_home_addr.a[0]<<8) + + smc->hw.fddi_home_addr.a[1])) ; + + outpw(FM_A(FM_SAGP),my_sagp) ; /* set short group address */ + + outpw(FM_A(FM_LAGL),(unsigned short)((smc->hw.fp.group_addr.a[4]<<8) + + smc->hw.fp.group_addr.a[5])) ; + outpw(FM_A(FM_LAGC),(unsigned short)((smc->hw.fp.group_addr.a[2]<<8) + + smc->hw.fp.group_addr.a[3])) ; + outpw(FM_A(FM_LAGM),(unsigned short)((smc->hw.fp.group_addr.a[0]<<8) + + smc->hw.fp.group_addr.a[1])) ; + + /* set r_request regs. (MSW & LSW of TRT ) */ + outpw(FM_A(FM_TREQ1),(unsigned short)(t_requ>>16)) ; + outpw(FM_A(FM_TREQ0),(unsigned short)t_requ) ; +} + +static void set_int(char *p, int l) +{ + p[0] = (char)(l >> 24) ; + p[1] = (char)(l >> 16) ; + p[2] = (char)(l >> 8) ; + p[3] = (char)(l >> 0) ; +} + +/* + * copy TX descriptor to buffer mem + * append FC field and MAC frame + * if more bit is set in descr + * append pointer to descriptor (endless loop) + * else + * append 'end of chain' pointer + */ +static void copy_tx_mac(struct s_smc *smc, u_long td, struct fddi_mac *mac, + unsigned int off, int len) +/* u_long td; transmit descriptor */ +/* struct fddi_mac *mac; mac frame pointer */ +/* unsigned int off; start address within buffer memory */ +/* int len ; length of the frame including the FC */ +{ + int i ; + __le32 *p ; + + CHECK_NPP() ; + MARW(off) ; /* set memory address reg for writes */ + + p = (__le32 *) mac ; + for (i = (len + 3)/4 ; i ; i--) { + if (i == 1) { + /* last word, set the tag bit */ + outpw(FM_A(FM_CMDREG2),FM_ISTTB) ; + } + write_mdr(smc,le32_to_cpu(*p)) ; + p++ ; + } + + outpw(FM_A(FM_CMDREG2),FM_ISTTB) ; /* set the tag bit */ + write_mdr(smc,td) ; /* write over memory data reg to buffer */ +} + +/* + BEGIN_MANUAL_ENTRY(module;tests;3) + How to test directed beacon frames + ---------------------------------------------------------------- + + o Insert a break point in the function build_claim_beacon() + before calling copy_tx_mac() for building the claim frame. + o Modify the RM3_DETECT case so that the RM6_DETECT state + will always entered from the RM3_DETECT state (function rmt_fsm(), + rmt.c) + o Compile the driver. + o Set the parameter TREQ in the protocol.ini or net.cfg to a + small value to make sure your station will win the claim + process. + o Start the driver. + o When you reach the break point, modify the SA and DA address + of the claim frame (e.g. SA = DA = 10005affffff). + o When you see RM3_DETECT and RM6_DETECT, observe the direct + beacon frames on the UPPSLANA. + + END_MANUAL_ENTRY + */ +static void directed_beacon(struct s_smc *smc) +{ + SK_LOC_DECL(__le32,a[2]) ; + + /* + * set UNA in frame + * enable FORMAC to send endless queue of directed beacon + * important: the UNA starts at byte 1 (not at byte 0) + */ + * (char *) a = (char) ((long)DBEACON_INFO<<24L) ; + a[1] = 0 ; + memcpy((char *)a+1, (char *) &smc->mib.m[MAC0].fddiMACUpstreamNbr, ETH_ALEN); + + CHECK_NPP() ; + /* set memory address reg for writes */ + MARW(smc->hw.fp.fifo.rbc_ram_start+DBEACON_FRAME_OFF+4) ; + write_mdr(smc,le32_to_cpu(a[0])) ; + outpw(FM_A(FM_CMDREG2),FM_ISTTB) ; /* set the tag bit */ + write_mdr(smc,le32_to_cpu(a[1])) ; + + outpw(FM_A(FM_SABC),smc->hw.fp.fifo.rbc_ram_start + DBEACON_FRAME_OFF) ; +} + +/* + setup claim & beacon pointer + NOTE : + special frame packets end with a pointer to their own + descriptor, and the MORE bit is set in the descriptor +*/ +static void build_claim_beacon(struct s_smc *smc, u_long t_request) +{ + u_int td ; + int len ; + struct fddi_mac_sf *mac ; + + /* + * build claim packet + */ + len = 17 ; + td = TX_DESCRIPTOR | ((((u_int)len-1)&3)<<27) ; + mac = &smc->hw.fp.mac_sfb ; + mac->mac_fc = FC_CLAIM ; + /* DA == SA in claim frame */ + mac->mac_source = mac->mac_dest = MA ; + /* 2's complement */ + set_int((char *)mac->mac_info,(int)t_request) ; + + copy_tx_mac(smc,td,(struct fddi_mac *)mac, + smc->hw.fp.fifo.rbc_ram_start + CLAIM_FRAME_OFF,len) ; + /* set CLAIM start pointer */ + outpw(FM_A(FM_SACL),smc->hw.fp.fifo.rbc_ram_start + CLAIM_FRAME_OFF) ; + + /* + * build beacon packet + */ + len = 17 ; + td = TX_DESCRIPTOR | ((((u_int)len-1)&3)<<27) ; + mac->mac_fc = FC_BEACON ; + mac->mac_source = MA ; + mac->mac_dest = null_addr ; /* DA == 0 in beacon frame */ + set_int((char *) mac->mac_info,((int)BEACON_INFO<<24) + 0 ) ; + + copy_tx_mac(smc,td,(struct fddi_mac *)mac, + smc->hw.fp.fifo.rbc_ram_start + BEACON_FRAME_OFF,len) ; + /* set beacon start pointer */ + outpw(FM_A(FM_SABC),smc->hw.fp.fifo.rbc_ram_start + BEACON_FRAME_OFF) ; + + /* + * build directed beacon packet + * contains optional UNA + */ + len = 23 ; + td = TX_DESCRIPTOR | ((((u_int)len-1)&3)<<27) ; + mac->mac_fc = FC_BEACON ; + mac->mac_source = MA ; + mac->mac_dest = dbeacon_multi ; /* multicast */ + set_int((char *) mac->mac_info,((int)DBEACON_INFO<<24) + 0 ) ; + set_int((char *) mac->mac_info+4,0) ; + set_int((char *) mac->mac_info+8,0) ; + + copy_tx_mac(smc,td,(struct fddi_mac *)mac, + smc->hw.fp.fifo.rbc_ram_start + DBEACON_FRAME_OFF,len) ; + + /* end of claim/beacon queue */ + outpw(FM_A(FM_EACB),smc->hw.fp.fifo.rx1_fifo_start-1) ; + + outpw(FM_A(FM_WPXSF),0) ; + outpw(FM_A(FM_RPXSF),0) ; +} + +static void formac_rcv_restart(struct s_smc *smc) +{ + /* enable receive function */ + SETMASK(FM_A(FM_MDREG1),smc->hw.fp.rx_mode,FM_ADDRX) ; + + outpw(FM_A(FM_CMDREG1),FM_ICLLR) ; /* clear receive lock */ +} + +void formac_tx_restart(struct s_smc *smc) +{ + outpw(FM_A(FM_CMDREG1),FM_ICLLS) ; /* clear s-frame lock */ + outpw(FM_A(FM_CMDREG1),FM_ICLLA0) ; /* clear a-frame lock */ +} + +static void enable_formac(struct s_smc *smc) +{ + /* set formac IMSK : 0 enables irq */ + outpw(FM_A(FM_IMSK1U),(unsigned short)~mac_imsk1u); + outpw(FM_A(FM_IMSK1L),(unsigned short)~mac_imsk1l); + outpw(FM_A(FM_IMSK2U),(unsigned short)~mac_imsk2u); + outpw(FM_A(FM_IMSK2L),(unsigned short)~mac_imsk2l); + outpw(FM_A(FM_IMSK3U),(unsigned short)~mac_imsk3u); + outpw(FM_A(FM_IMSK3L),(unsigned short)~mac_imsk3l); +} + +#if 0 /* Removed because the driver should use the ASICs TX complete IRQ. */ + /* The FORMACs tx complete IRQ should be used any longer */ + +/* + BEGIN_MANUAL_ENTRY(if,func;others;4) + + void enable_tx_irq(smc, queue) + struct s_smc *smc ; + u_short queue ; + +Function DOWNCALL (SMT, fplustm.c) + enable_tx_irq() enables the FORMACs transmit complete + interrupt of the queue. + +Para queue = QUEUE_S: synchronous queue + = QUEUE_A0: asynchronous queue + +Note After any ring operational change the transmit complete + interrupts are disabled. + The operating system dependent module must enable + the transmit complete interrupt of a queue, + - when it queues the first frame, + because of no transmit resources are beeing + available and + - when it escapes from the function llc_restart_tx + while some frames are still queued. + + END_MANUAL_ENTRY + */ +void enable_tx_irq(struct s_smc *smc, u_short queue) +/* u_short queue; 0 = synchronous queue, 1 = asynchronous queue 0 */ +{ + u_short imask ; + + imask = ~(inpw(FM_A(FM_IMSK1U))) ; + + if (queue == 0) { + outpw(FM_A(FM_IMSK1U),~(imask|FM_STEFRMS)) ; + } + if (queue == 1) { + outpw(FM_A(FM_IMSK1U),~(imask|FM_STEFRMA0)) ; + } +} + +/* + BEGIN_MANUAL_ENTRY(if,func;others;4) + + void disable_tx_irq(smc, queue) + struct s_smc *smc ; + u_short queue ; + +Function DOWNCALL (SMT, fplustm.c) + disable_tx_irq disables the FORMACs transmit complete + interrupt of the queue + +Para queue = QUEUE_S: synchronous queue + = QUEUE_A0: asynchronous queue + +Note The operating system dependent module should disable + the transmit complete interrupts if it escapes from the + function llc_restart_tx and no frames are queued. + + END_MANUAL_ENTRY + */ +void disable_tx_irq(struct s_smc *smc, u_short queue) +/* u_short queue; 0 = synchronous queue, 1 = asynchronous queue 0 */ +{ + u_short imask ; + + imask = ~(inpw(FM_A(FM_IMSK1U))) ; + + if (queue == 0) { + outpw(FM_A(FM_IMSK1U),~(imask&~FM_STEFRMS)) ; + } + if (queue == 1) { + outpw(FM_A(FM_IMSK1U),~(imask&~FM_STEFRMA0)) ; + } +} +#endif + +static void disable_formac(struct s_smc *smc) +{ + /* clear formac IMSK : 1 disables irq */ + outpw(FM_A(FM_IMSK1U),MW) ; + outpw(FM_A(FM_IMSK1L),MW) ; + outpw(FM_A(FM_IMSK2U),MW) ; + outpw(FM_A(FM_IMSK2L),MW) ; + outpw(FM_A(FM_IMSK3U),MW) ; + outpw(FM_A(FM_IMSK3L),MW) ; +} + + +static void mac_ring_up(struct s_smc *smc, int up) +{ + if (up) { + formac_rcv_restart(smc) ; /* enable receive function */ + smc->hw.mac_ring_is_up = TRUE ; + llc_restart_tx(smc) ; /* TX queue */ + } + else { + /* disable receive function */ + SETMASK(FM_A(FM_MDREG1),FM_MDISRCV,FM_ADDET) ; + + /* abort current transmit activity */ + outpw(FM_A(FM_CMDREG2),FM_IACTR) ; + + smc->hw.mac_ring_is_up = FALSE ; + } +} + +/*--------------------------- ISR handling ----------------------------------*/ +/* + * mac1_irq is in drvfbi.c + */ + +/* + * mac2_irq: status bits for the receive queue 1, and ring status + * ring status indication bits + */ +void mac2_irq(struct s_smc *smc, u_short code_s2u, u_short code_s2l) +{ + u_short change_s2l ; + u_short change_s2u ; + + /* (jd) 22-Feb-1999 + * Restart 2_DMax Timer after end of claiming or beaconing + */ + if (code_s2u & (FM_SCLM|FM_SHICLM|FM_SBEC|FM_SOTRBEC)) { + queue_event(smc,EVENT_RMT,RM_TX_STATE_CHANGE) ; + } + else if (code_s2l & (FM_STKISS)) { + queue_event(smc,EVENT_RMT,RM_TX_STATE_CHANGE) ; + } + + /* + * XOR current st bits with the last to avoid useless RMT event queuing + */ + change_s2l = smc->hw.fp.s2l ^ code_s2l ; + change_s2u = smc->hw.fp.s2u ^ code_s2u ; + + if ((change_s2l & FM_SRNGOP) || + (!smc->hw.mac_ring_is_up && ((code_s2l & FM_SRNGOP)))) { + if (code_s2l & FM_SRNGOP) { + mac_ring_up(smc,1) ; + queue_event(smc,EVENT_RMT,RM_RING_OP) ; + smc->mib.m[MAC0].fddiMACRingOp_Ct++ ; + } + else { + mac_ring_up(smc,0) ; + queue_event(smc,EVENT_RMT,RM_RING_NON_OP) ; + } + goto mac2_end ; + } + if (code_s2l & FM_SMISFRM) { /* missed frame */ + smc->mib.m[MAC0].fddiMACNotCopied_Ct++ ; + } + if (code_s2u & (FM_SRCVOVR | /* recv. FIFO overflow */ + FM_SRBFL)) { /* recv. buffer full */ + smc->hw.mac_ct.mac_r_restart_counter++ ; +/* formac_rcv_restart(smc) ; */ + smt_stat_counter(smc,1) ; +/* goto mac2_end ; */ + } + if (code_s2u & FM_SOTRBEC) + queue_event(smc,EVENT_RMT,RM_OTHER_BEACON) ; + if (code_s2u & FM_SMYBEC) + queue_event(smc,EVENT_RMT,RM_MY_BEACON) ; + if (change_s2u & code_s2u & FM_SLOCLM) { + DB_RMTN(2,"RMT : lower claim received\n",0,0) ; + } + if ((code_s2u & FM_SMYCLM) && !(code_s2l & FM_SDUPCLM)) { + /* + * This is my claim and that claim is not detected as a + * duplicate one. + */ + queue_event(smc,EVENT_RMT,RM_MY_CLAIM) ; + } + if (code_s2l & FM_SDUPCLM) { + /* + * If a duplicate claim frame (same SA but T_Bid != T_Req) + * this flag will be set. + * In the RMT state machine we need a RM_VALID_CLAIM event + * to do the appropriate state change. + * RM(34c) + */ + queue_event(smc,EVENT_RMT,RM_VALID_CLAIM) ; + } + if (change_s2u & code_s2u & FM_SHICLM) { + DB_RMTN(2,"RMT : higher claim received\n",0,0) ; + } + if ( (code_s2l & FM_STRTEXP) || + (code_s2l & FM_STRTEXR) ) + queue_event(smc,EVENT_RMT,RM_TRT_EXP) ; + if (code_s2l & FM_SMULTDA) { + /* + * The MAC has found a 2. MAC with the same address. + * Signal dup_addr_test = failed to RMT state machine. + * RM(25) + */ + smc->r.dup_addr_test = DA_FAILED ; + queue_event(smc,EVENT_RMT,RM_DUP_ADDR) ; + } + if (code_s2u & FM_SBEC) + smc->hw.fp.err_stats.err_bec_stat++ ; + if (code_s2u & FM_SCLM) + smc->hw.fp.err_stats.err_clm_stat++ ; + if (code_s2l & FM_STVXEXP) + smc->mib.m[MAC0].fddiMACTvxExpired_Ct++ ; + if ((code_s2u & (FM_SBEC|FM_SCLM))) { + if (!(change_s2l & FM_SRNGOP) && (smc->hw.fp.s2l & FM_SRNGOP)) { + mac_ring_up(smc,0) ; + queue_event(smc,EVENT_RMT,RM_RING_NON_OP) ; + + mac_ring_up(smc,1) ; + queue_event(smc,EVENT_RMT,RM_RING_OP) ; + smc->mib.m[MAC0].fddiMACRingOp_Ct++ ; + } + } + if (code_s2l & FM_SPHINV) + smc->hw.fp.err_stats.err_phinv++ ; + if (code_s2l & FM_SSIFG) + smc->hw.fp.err_stats.err_sifg_det++ ; + if (code_s2l & FM_STKISS) + smc->hw.fp.err_stats.err_tkiss++ ; + if (code_s2l & FM_STKERR) + smc->hw.fp.err_stats.err_tkerr++ ; + if (code_s2l & FM_SFRMCTR) + smc->mib.m[MAC0].fddiMACFrame_Ct += 0x10000L ; + if (code_s2l & FM_SERRCTR) + smc->mib.m[MAC0].fddiMACError_Ct += 0x10000L ; + if (code_s2l & FM_SLSTCTR) + smc->mib.m[MAC0].fddiMACLost_Ct += 0x10000L ; + if (code_s2u & FM_SERRSF) { + SMT_PANIC(smc,SMT_E0114, SMT_E0114_MSG) ; + } +mac2_end: + /* notice old status */ + smc->hw.fp.s2l = code_s2l ; + smc->hw.fp.s2u = code_s2u ; + outpw(FM_A(FM_IMSK2U),~mac_imsk2u) ; +} + +/* + * mac3_irq: receive queue 2 bits and address detection bits + */ +void mac3_irq(struct s_smc *smc, u_short code_s3u, u_short code_s3l) +{ + UNUSED(code_s3l) ; + + if (code_s3u & (FM_SRCVOVR2 | /* recv. FIFO overflow */ + FM_SRBFL2)) { /* recv. buffer full */ + smc->hw.mac_ct.mac_r_restart_counter++ ; + smt_stat_counter(smc,1); + } + + + if (code_s3u & FM_SRPERRQ2) { /* parity error receive queue 2 */ + SMT_PANIC(smc,SMT_E0115, SMT_E0115_MSG) ; + } + if (code_s3u & FM_SRPERRQ1) { /* parity error receive queue 2 */ + SMT_PANIC(smc,SMT_E0116, SMT_E0116_MSG) ; + } +} + + +/* + * take formac offline + */ +static void formac_offline(struct s_smc *smc) +{ + outpw(FM_A(FM_CMDREG2),FM_IACTR) ;/* abort current transmit activity */ + + /* disable receive function */ + SETMASK(FM_A(FM_MDREG1),FM_MDISRCV,FM_ADDET) ; + + /* FORMAC+ 'Initialize Mode' */ + SETMASK(FM_A(FM_MDREG1),FM_MINIT,FM_MMODE) ; + + disable_formac(smc) ; + smc->hw.mac_ring_is_up = FALSE ; + smc->hw.hw_state = STOPPED ; +} + +/* + * bring formac online + */ +static void formac_online(struct s_smc *smc) +{ + enable_formac(smc) ; + SETMASK(FM_A(FM_MDREG1),FM_MONLINE | FM_SELRA | MDR1INIT | + smc->hw.fp.rx_mode, FM_MMODE | FM_SELRA | FM_ADDRX) ; +} + +/* + * FORMAC+ full init. (tx, rx, timer, counter, claim & beacon) + */ +int init_fplus(struct s_smc *smc) +{ + smc->hw.fp.nsa_mode = FM_MRNNSAFNMA ; + smc->hw.fp.rx_mode = FM_MDAMA ; + smc->hw.fp.group_addr = fddi_broadcast ; + smc->hw.fp.func_addr = 0 ; + smc->hw.fp.frselreg_init = 0 ; + + init_driver_fplus(smc) ; + if (smc->s.sas == SMT_DAS) + smc->hw.fp.mdr3init |= FM_MENDAS ; + + smc->hw.mac_ct.mac_nobuf_counter = 0 ; + smc->hw.mac_ct.mac_r_restart_counter = 0 ; + + smc->hw.fp.fm_st1u = (HW_PTR) ADDR(B0_ST1U) ; + smc->hw.fp.fm_st1l = (HW_PTR) ADDR(B0_ST1L) ; + smc->hw.fp.fm_st2u = (HW_PTR) ADDR(B0_ST2U) ; + smc->hw.fp.fm_st2l = (HW_PTR) ADDR(B0_ST2L) ; + smc->hw.fp.fm_st3u = (HW_PTR) ADDR(B0_ST3U) ; + smc->hw.fp.fm_st3l = (HW_PTR) ADDR(B0_ST3L) ; + + smc->hw.fp.s2l = smc->hw.fp.s2u = 0 ; + smc->hw.mac_ring_is_up = 0 ; + + mac_counter_init(smc) ; + + /* convert BCKL units to symbol time */ + smc->hw.mac_pa.t_neg = (u_long)0 ; + smc->hw.mac_pa.t_pri = (u_long)0 ; + + /* make sure all PCI settings are correct */ + mac_do_pci_fix(smc) ; + + return init_mac(smc, 1); + /* enable_formac(smc) ; */ +} + +static int init_mac(struct s_smc *smc, int all) +{ + u_short t_max,x ; + u_long time=0 ; + + /* + * clear memory + */ + outpw(FM_A(FM_MDREG1),FM_MINIT) ; /* FORMAC+ init mode */ + set_formac_addr(smc) ; + outpw(FM_A(FM_MDREG1),FM_MMEMACT) ; /* FORMAC+ memory activ mode */ + /* Note: Mode register 2 is set here, incase parity is enabled. */ + outpw(FM_A(FM_MDREG2),smc->hw.fp.mdr2init) ; + + if (all) { + init_ram(smc) ; + } + else { + /* + * reset the HPI, the Master and the BMUs + */ + outp(ADDR(B0_CTRL), CTRL_HPI_SET) ; + time = hwt_quick_read(smc) ; + } + + /* + * set all pointers, frames etc + */ + smt_split_up_fifo(smc) ; + + init_tx(smc) ; + init_rx(smc) ; + init_rbc(smc) ; + + build_claim_beacon(smc,smc->mib.m[MAC0].fddiMACT_Req) ; + + /* set RX threshold */ + /* see Errata #SN2 Phantom receive overflow */ + outpw(FM_A(FM_FRMTHR),14<<12) ; /* switch on */ + + /* set formac work mode */ + outpw(FM_A(FM_MDREG1),MDR1INIT | FM_SELRA | smc->hw.fp.rx_mode) ; + outpw(FM_A(FM_MDREG2),smc->hw.fp.mdr2init) ; + outpw(FM_A(FM_MDREG3),smc->hw.fp.mdr3init) ; + outpw(FM_A(FM_FRSELREG),smc->hw.fp.frselreg_init) ; + + /* set timer */ + /* + * errata #22 fplus: + * T_MAX must not be FFFE + * or one of FFDF, FFB8, FF91 (-0x27 etc..) + */ + t_max = (u_short)(smc->mib.m[MAC0].fddiMACT_Max/32) ; + x = t_max/0x27 ; + x *= 0x27 ; + if ((t_max == 0xfffe) || (t_max - x == 0x16)) + t_max-- ; + outpw(FM_A(FM_TMAX),(u_short)t_max) ; + + /* BugFix for report #10204 */ + if (smc->mib.m[MAC0].fddiMACTvxValue < (u_long) (- US2BCLK(52))) { + outpw(FM_A(FM_TVX), (u_short) (- US2BCLK(52))/255 & MB) ; + } else { + outpw(FM_A(FM_TVX), + (u_short)((smc->mib.m[MAC0].fddiMACTvxValue/255) & MB)) ; + } + + outpw(FM_A(FM_CMDREG1),FM_ICLLS) ; /* clear s-frame lock */ + outpw(FM_A(FM_CMDREG1),FM_ICLLA0) ; /* clear a-frame lock */ + outpw(FM_A(FM_CMDREG1),FM_ICLLR); /* clear receive lock */ + + /* Auto unlock receice threshold for receive queue 1 and 2 */ + outpw(FM_A(FM_UNLCKDLY),(0xff|(0xff<<8))) ; + + rtm_init(smc) ; /* RT-Monitor */ + + if (!all) { + /* + * after 10ms, reset the BMUs and repair the rings + */ + hwt_wait_time(smc,time,MS2BCLK(10)) ; + outpd(ADDR(B0_R1_CSR),CSR_SET_RESET) ; + outpd(ADDR(B0_XA_CSR),CSR_SET_RESET) ; + outpd(ADDR(B0_XS_CSR),CSR_SET_RESET) ; + outp(ADDR(B0_CTRL), CTRL_HPI_CLR) ; + outpd(ADDR(B0_R1_CSR),CSR_CLR_RESET) ; + outpd(ADDR(B0_XA_CSR),CSR_CLR_RESET) ; + outpd(ADDR(B0_XS_CSR),CSR_CLR_RESET) ; + if (!smc->hw.hw_is_64bit) { + outpd(ADDR(B4_R1_F), RX_WATERMARK) ; + outpd(ADDR(B5_XA_F), TX_WATERMARK) ; + outpd(ADDR(B5_XS_F), TX_WATERMARK) ; + } + smc->hw.hw_state = STOPPED ; + mac_drv_repair_descr(smc) ; + } + smc->hw.hw_state = STARTED ; + + return 0; +} + + +/* + * called by CFM + */ +void config_mux(struct s_smc *smc, int mux) +{ + plc_config_mux(smc,mux) ; + + SETMASK(FM_A(FM_MDREG1),FM_SELRA,FM_SELRA) ; +} + +/* + * called by RMT + * enable CLAIM/BEACON interrupts + * (only called if these events are of interest, e.g. in DETECT state + * the interrupt must not be permanently enabled + * RMT calls this function periodically (timer driven polling) + */ +void sm_mac_check_beacon_claim(struct s_smc *smc) +{ + /* set formac IMSK : 0 enables irq */ + outpw(FM_A(FM_IMSK2U),~(mac_imsk2u | mac_beacon_imsk2u)) ; + /* the driver must receive the directed beacons */ + formac_rcv_restart(smc) ; + process_receive(smc) ; +} + +/*-------------------------- interface functions ----------------------------*/ +/* + * control MAC layer (called by RMT) + */ +void sm_ma_control(struct s_smc *smc, int mode) +{ + switch(mode) { + case MA_OFFLINE : + /* Add to make the MAC offline in RM0_ISOLATED state */ + formac_offline(smc) ; + break ; + case MA_RESET : + (void)init_mac(smc,0) ; + break ; + case MA_BEACON : + formac_online(smc) ; + break ; + case MA_DIRECTED : + directed_beacon(smc) ; + break ; + case MA_TREQ : + /* + * no actions necessary, TREQ is already set + */ + break ; + } +} + +int sm_mac_get_tx_state(struct s_smc *smc) +{ + return (inpw(FM_A(FM_STMCHN))>>4) & 7; +} + +/* + * multicast functions + */ + +static struct s_fpmc* mac_get_mc_table(struct s_smc *smc, + struct fddi_addr *user, + struct fddi_addr *own, + int del, int can) +{ + struct s_fpmc *tb ; + struct s_fpmc *slot ; + u_char *p ; + int i ; + + /* + * set own = can(user) + */ + *own = *user ; + if (can) { + p = own->a ; + for (i = 0 ; i < 6 ; i++, p++) + *p = bitrev8(*p); + } + slot = NULL; + for (i = 0, tb = smc->hw.fp.mc.table ; i < FPMAX_MULTICAST ; i++, tb++){ + if (!tb->n) { /* not used */ + if (!del && !slot) /* if !del save first free */ + slot = tb ; + continue ; + } + if (!ether_addr_equal((char *)&tb->a, (char *)own)) + continue ; + return tb; + } + return slot; /* return first free or NULL */ +} + +/* + BEGIN_MANUAL_ENTRY(if,func;others;2) + + void mac_clear_multicast(smc) + struct s_smc *smc ; + +Function DOWNCALL (SMT, fplustm.c) + Clear all multicast entries + + END_MANUAL_ENTRY() + */ +void mac_clear_multicast(struct s_smc *smc) +{ + struct s_fpmc *tb ; + int i ; + + smc->hw.fp.os_slots_used = 0 ; /* note the SMT addresses */ + /* will not be deleted */ + for (i = 0, tb = smc->hw.fp.mc.table ; i < FPMAX_MULTICAST ; i++, tb++){ + if (!tb->perm) { + tb->n = 0 ; + } + } +} + +/* + BEGIN_MANUAL_ENTRY(if,func;others;2) + + int mac_add_multicast(smc,addr,can) + struct s_smc *smc ; + struct fddi_addr *addr ; + int can ; + +Function DOWNCALL (SMC, fplustm.c) + Add an entry to the multicast table + +Para addr pointer to a multicast address + can = 0: the multicast address has the physical format + = 1: the multicast address has the canonical format + | 0x80 permanent + +Returns 0: success + 1: address table full + +Note After a 'driver reset' or a 'station set address' all + entries of the multicast table are cleared. + In this case the driver has to fill the multicast table again. + After the operating system dependent module filled + the multicast table it must call mac_update_multicast + to activate the new multicast addresses! + + END_MANUAL_ENTRY() + */ +int mac_add_multicast(struct s_smc *smc, struct fddi_addr *addr, int can) +{ + SK_LOC_DECL(struct fddi_addr,own) ; + struct s_fpmc *tb ; + + /* + * check if there are free table entries + */ + if (can & 0x80) { + if (smc->hw.fp.smt_slots_used >= SMT_MAX_MULTI) { + return 1; + } + } + else { + if (smc->hw.fp.os_slots_used >= FPMAX_MULTICAST-SMT_MAX_MULTI) { + return 1; + } + } + + /* + * find empty slot + */ + if (!(tb = mac_get_mc_table(smc,addr,&own,0,can & ~0x80))) + return 1; + tb->n++ ; + tb->a = own ; + tb->perm = (can & 0x80) ? 1 : 0 ; + + if (can & 0x80) + smc->hw.fp.smt_slots_used++ ; + else + smc->hw.fp.os_slots_used++ ; + + return 0; +} + +/* + * mode + */ + +#define RX_MODE_PROM 0x1 +#define RX_MODE_ALL_MULTI 0x2 + +/* + BEGIN_MANUAL_ENTRY(if,func;others;2) + + void mac_update_multicast(smc) + struct s_smc *smc ; + +Function DOWNCALL (SMT, fplustm.c) + Update FORMAC multicast registers + + END_MANUAL_ENTRY() + */ +void mac_update_multicast(struct s_smc *smc) +{ + struct s_fpmc *tb ; + u_char *fu ; + int i ; + + /* + * invalidate the CAM + */ + outpw(FM_A(FM_AFCMD),FM_IINV_CAM) ; + + /* + * set the functional address + */ + if (smc->hw.fp.func_addr) { + fu = (u_char *) &smc->hw.fp.func_addr ; + outpw(FM_A(FM_AFMASK2),0xffff) ; + outpw(FM_A(FM_AFMASK1),(u_short) ~((fu[0] << 8) + fu[1])) ; + outpw(FM_A(FM_AFMASK0),(u_short) ~((fu[2] << 8) + fu[3])) ; + outpw(FM_A(FM_AFPERS),FM_VALID|FM_DA) ; + outpw(FM_A(FM_AFCOMP2), 0xc000) ; + outpw(FM_A(FM_AFCOMP1), 0x0000) ; + outpw(FM_A(FM_AFCOMP0), 0x0000) ; + outpw(FM_A(FM_AFCMD),FM_IWRITE_CAM) ; + } + + /* + * set the mask and the personality register(s) + */ + outpw(FM_A(FM_AFMASK0),0xffff) ; + outpw(FM_A(FM_AFMASK1),0xffff) ; + outpw(FM_A(FM_AFMASK2),0xffff) ; + outpw(FM_A(FM_AFPERS),FM_VALID|FM_DA) ; + + for (i = 0, tb = smc->hw.fp.mc.table; i < FPMAX_MULTICAST; i++, tb++) { + if (tb->n) { + CHECK_CAM() ; + + /* + * write the multicast address into the CAM + */ + outpw(FM_A(FM_AFCOMP2), + (u_short)((tb->a.a[0]<<8)+tb->a.a[1])) ; + outpw(FM_A(FM_AFCOMP1), + (u_short)((tb->a.a[2]<<8)+tb->a.a[3])) ; + outpw(FM_A(FM_AFCOMP0), + (u_short)((tb->a.a[4]<<8)+tb->a.a[5])) ; + outpw(FM_A(FM_AFCMD),FM_IWRITE_CAM) ; + } + } +} + +/* + BEGIN_MANUAL_ENTRY(if,func;others;3) + + void mac_set_rx_mode(smc,mode) + struct s_smc *smc ; + int mode ; + +Function DOWNCALL/INTERN (SMT, fplustm.c) + This function enables / disables the selected receive. + Don't call this function if the hardware module is + used -- use mac_drv_rx_mode() instead of. + +Para mode = 1 RX_ENABLE_ALLMULTI enable all multicasts + 2 RX_DISABLE_ALLMULTI disable "enable all multicasts" + 3 RX_ENABLE_PROMISC enable promiscuous + 4 RX_DISABLE_PROMISC disable promiscuous + 5 RX_ENABLE_NSA enable reception of NSA frames + 6 RX_DISABLE_NSA disable reception of NSA frames + +Note The selected receive modes will be lost after 'driver reset' + or 'set station address' + + END_MANUAL_ENTRY + */ +void mac_set_rx_mode(struct s_smc *smc, int mode) +{ + switch (mode) { + case RX_ENABLE_ALLMULTI : + smc->hw.fp.rx_prom |= RX_MODE_ALL_MULTI ; + break ; + case RX_DISABLE_ALLMULTI : + smc->hw.fp.rx_prom &= ~RX_MODE_ALL_MULTI ; + break ; + case RX_ENABLE_PROMISC : + smc->hw.fp.rx_prom |= RX_MODE_PROM ; + break ; + case RX_DISABLE_PROMISC : + smc->hw.fp.rx_prom &= ~RX_MODE_PROM ; + break ; + case RX_ENABLE_NSA : + smc->hw.fp.nsa_mode = FM_MDAMA ; + smc->hw.fp.rx_mode = (smc->hw.fp.rx_mode & ~FM_ADDET) | + smc->hw.fp.nsa_mode ; + break ; + case RX_DISABLE_NSA : + smc->hw.fp.nsa_mode = FM_MRNNSAFNMA ; + smc->hw.fp.rx_mode = (smc->hw.fp.rx_mode & ~FM_ADDET) | + smc->hw.fp.nsa_mode ; + break ; + } + if (smc->hw.fp.rx_prom & RX_MODE_PROM) { + smc->hw.fp.rx_mode = FM_MLIMPROM ; + } + else if (smc->hw.fp.rx_prom & RX_MODE_ALL_MULTI) { + smc->hw.fp.rx_mode = smc->hw.fp.nsa_mode | FM_EXGPA0 ; + } + else + smc->hw.fp.rx_mode = smc->hw.fp.nsa_mode ; + SETMASK(FM_A(FM_MDREG1),smc->hw.fp.rx_mode,FM_ADDRX) ; + mac_update_multicast(smc) ; +} + +/* + BEGIN_MANUAL_ENTRY(module;tests;3) + How to test the Restricted Token Monitor + ---------------------------------------------------------------- + + o Insert a break point in the function rtm_irq() + o Remove all stations with a restricted token monitor from the + network. + o Connect a UPPS ISA or EISA station to the network. + o Give the FORMAC of UPPS station the command to send + restricted tokens until the ring becomes instable. + o Now connect your test test client. + o The restricted token monitor should detect the restricted token, + and your break point will be reached. + o You can ovserve how the station will clean the ring. + + END_MANUAL_ENTRY + */ +void rtm_irq(struct s_smc *smc) +{ + outpw(ADDR(B2_RTM_CRTL),TIM_CL_IRQ) ; /* clear IRQ */ + if (inpw(ADDR(B2_RTM_CRTL)) & TIM_RES_TOK) { + outpw(FM_A(FM_CMDREG1),FM_ICL) ; /* force claim */ + DB_RMT("RMT: fddiPATHT_Rmode expired\n",0,0) ; + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, + (u_long) FDDI_SMT_EVENT, + (u_long) FDDI_RTT, smt_get_event_word(smc)); + } + outpw(ADDR(B2_RTM_CRTL),TIM_START) ; /* enable RTM monitoring */ +} + +static void rtm_init(struct s_smc *smc) +{ + outpd(ADDR(B2_RTM_INI),0) ; /* timer = 0 */ + outpw(ADDR(B2_RTM_CRTL),TIM_START) ; /* enable IRQ */ +} + +void rtm_set_timer(struct s_smc *smc) +{ + /* + * MIB timer and hardware timer have the same resolution of 80nS + */ + DB_RMT("RMT: setting new fddiPATHT_Rmode, t = %d ns\n", + (int) smc->mib.a[PATH0].fddiPATHT_Rmode,0) ; + outpd(ADDR(B2_RTM_INI),smc->mib.a[PATH0].fddiPATHT_Rmode) ; +} + +static void smt_split_up_fifo(struct s_smc *smc) +{ + +/* + BEGIN_MANUAL_ENTRY(module;mem;1) + ------------------------------------------------------------- + RECEIVE BUFFER MEMORY DIVERSION + ------------------------------------------------------------- + + R1_RxD == SMT_R1_RXD_COUNT + R2_RxD == SMT_R2_RXD_COUNT + + SMT_R1_RXD_COUNT must be unequal zero + + | R1_RxD R2_RxD |R1_RxD R2_RxD | R1_RxD R2_RxD + | x 0 | x 1-3 | x < 3 + ---------------------------------------------------------------------- + | 63,75 kB | 54,75 | R1_RxD + rx queue 1 | RX_FIFO_SPACE | RX_LARGE_FIFO| ------------- * 63,75 kB + | | | R1_RxD+R2_RxD + ---------------------------------------------------------------------- + | | 9 kB | R2_RxD + rx queue 2 | 0 kB | RX_SMALL_FIFO| ------------- * 63,75 kB + | (not used) | | R1_RxD+R2_RxD + + END_MANUAL_ENTRY +*/ + + if (SMT_R1_RXD_COUNT == 0) { + SMT_PANIC(smc,SMT_E0117, SMT_E0117_MSG) ; + } + + switch(SMT_R2_RXD_COUNT) { + case 0: + smc->hw.fp.fifo.rx1_fifo_size = RX_FIFO_SPACE ; + smc->hw.fp.fifo.rx2_fifo_size = 0 ; + break ; + case 1: + case 2: + case 3: + smc->hw.fp.fifo.rx1_fifo_size = RX_LARGE_FIFO ; + smc->hw.fp.fifo.rx2_fifo_size = RX_SMALL_FIFO ; + break ; + default: /* this is not the real defaule */ + smc->hw.fp.fifo.rx1_fifo_size = RX_FIFO_SPACE * + SMT_R1_RXD_COUNT/(SMT_R1_RXD_COUNT+SMT_R2_RXD_COUNT) ; + smc->hw.fp.fifo.rx2_fifo_size = RX_FIFO_SPACE * + SMT_R2_RXD_COUNT/(SMT_R1_RXD_COUNT+SMT_R2_RXD_COUNT) ; + break ; + } + +/* + BEGIN_MANUAL_ENTRY(module;mem;1) + ------------------------------------------------------------- + TRANSMIT BUFFER MEMORY DIVERSION + ------------------------------------------------------------- + + + | no sync bw | sync bw available and | sync bw available and + | available | SynchTxMode = SPLIT | SynchTxMode = ALL + ----------------------------------------------------------------------- + sync tx | 0 kB | 32 kB | 55 kB + queue | | TX_MEDIUM_FIFO | TX_LARGE_FIFO + ----------------------------------------------------------------------- + async tx | 64 kB | 32 kB | 9 k + queue | TX_FIFO_SPACE| TX_MEDIUM_FIFO | TX_SMALL_FIFO + + END_MANUAL_ENTRY +*/ + + /* + * set the tx mode bits + */ + if (smc->mib.a[PATH0].fddiPATHSbaPayload) { +#ifdef ESS + smc->hw.fp.fifo.fifo_config_mode |= + smc->mib.fddiESSSynchTxMode | SYNC_TRAFFIC_ON ; +#endif + } + else { + smc->hw.fp.fifo.fifo_config_mode &= + ~(SEND_ASYNC_AS_SYNC|SYNC_TRAFFIC_ON) ; + } + + /* + * split up the FIFO + */ + if (smc->hw.fp.fifo.fifo_config_mode & SYNC_TRAFFIC_ON) { + if (smc->hw.fp.fifo.fifo_config_mode & SEND_ASYNC_AS_SYNC) { + smc->hw.fp.fifo.tx_s_size = TX_LARGE_FIFO ; + smc->hw.fp.fifo.tx_a0_size = TX_SMALL_FIFO ; + } + else { + smc->hw.fp.fifo.tx_s_size = TX_MEDIUM_FIFO ; + smc->hw.fp.fifo.tx_a0_size = TX_MEDIUM_FIFO ; + } + } + else { + smc->hw.fp.fifo.tx_s_size = 0 ; + smc->hw.fp.fifo.tx_a0_size = TX_FIFO_SPACE ; + } + + smc->hw.fp.fifo.rx1_fifo_start = smc->hw.fp.fifo.rbc_ram_start + + RX_FIFO_OFF ; + smc->hw.fp.fifo.tx_s_start = smc->hw.fp.fifo.rx1_fifo_start + + smc->hw.fp.fifo.rx1_fifo_size ; + smc->hw.fp.fifo.tx_a0_start = smc->hw.fp.fifo.tx_s_start + + smc->hw.fp.fifo.tx_s_size ; + smc->hw.fp.fifo.rx2_fifo_start = smc->hw.fp.fifo.tx_a0_start + + smc->hw.fp.fifo.tx_a0_size ; + + DB_SMT("FIFO split: mode = %x\n",smc->hw.fp.fifo.fifo_config_mode,0) ; + DB_SMT("rbc_ram_start = %x rbc_ram_end = %x\n", + smc->hw.fp.fifo.rbc_ram_start, smc->hw.fp.fifo.rbc_ram_end) ; + DB_SMT("rx1_fifo_start = %x tx_s_start = %x\n", + smc->hw.fp.fifo.rx1_fifo_start, smc->hw.fp.fifo.tx_s_start) ; + DB_SMT("tx_a0_start = %x rx2_fifo_start = %x\n", + smc->hw.fp.fifo.tx_a0_start, smc->hw.fp.fifo.rx2_fifo_start) ; +} + +void formac_reinit_tx(struct s_smc *smc) +{ + /* + * Split up the FIFO and reinitialize the MAC if synchronous + * bandwidth becomes available but no synchronous queue is + * configured. + */ + if (!smc->hw.fp.fifo.tx_s_size && smc->mib.a[PATH0].fddiPATHSbaPayload){ + (void)init_mac(smc,0) ; + } +} + diff --git a/kernel/drivers/net/fddi/skfp/h/cmtdef.h b/kernel/drivers/net/fddi/skfp/h/cmtdef.h new file mode 100644 index 000000000..f5bc90ff2 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/cmtdef.h @@ -0,0 +1,756 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _CMTDEF_ +#define _CMTDEF_ + +/* **************************************************************** */ + +/* + * implementation specific constants + * MODIIFY THE FOLLOWING THREE DEFINES + */ +#define AMDPLC /* if Amd PLC chip used */ +#ifdef CONC +#define NUMPHYS 12 /* 2 for SAS or DAS, more for Concentrator */ +#else +#ifdef CONC_II +#define NUMPHYS 24 /* 2 for SAS or DAS, more for Concentrator */ +#else +#define NUMPHYS 2 /* 2 for SAS or DAS, more for Concentrator */ +#endif +#endif +#define NUMMACS 1 /* only 1 supported at the moment */ +#define NUMPATHS 2 /* primary and secondary path supported */ + +/* + * DO NOT MODIFY BEYOND THIS POINT + */ + +/* **************************************************************** */ + +#if NUMPHYS > 2 +#define CONCENTRATOR +#endif + +/* + * Definitions for comfortable LINT usage + */ +#ifdef lint +#define LINT_USE(x) (x)=(x) +#else +#define LINT_USE(x) +#endif + +#ifdef DEBUG +#define DB_PR(flag,a,b,c) { if (flag) printf(a,b,c) ; } +#else +#define DB_PR(flag,a,b,c) +#endif + +#ifdef DEBUG_BRD +#define DB_ECM(a,b,c) DB_PR((smc->debug.d_smt&1),a,b,c) +#define DB_ECMN(n,a,b,c) DB_PR((smc->debug.d_ecm >=(n)),a,b,c) +#define DB_RMT(a,b,c) DB_PR((smc->debug.d_smt&2),a,b,c) +#define DB_RMTN(n,a,b,c) DB_PR((smc->debug.d_rmt >=(n)),a,b,c) +#define DB_CFM(a,b,c) DB_PR((smc->debug.d_smt&4),a,b,c) +#define DB_CFMN(n,a,b,c) DB_PR((smc->debug.d_cfm >=(n)),a,b,c) +#define DB_PCM(a,b,c) DB_PR((smc->debug.d_smt&8),a,b,c) +#define DB_PCMN(n,a,b,c) DB_PR((smc->debug.d_pcm >=(n)),a,b,c) +#define DB_SMT(a,b,c) DB_PR((smc->debug.d_smtf),a,b,c) +#define DB_SMTN(n,a,b,c) DB_PR((smc->debug.d_smtf >=(n)),a,b,c) +#define DB_SBA(a,b,c) DB_PR((smc->debug.d_sba),a,b,c) +#define DB_SBAN(n,a,b,c) DB_PR((smc->debug.d_sba >=(n)),a,b,c) +#define DB_ESS(a,b,c) DB_PR((smc->debug.d_ess),a,b,c) +#define DB_ESSN(n,a,b,c) DB_PR((smc->debug.d_ess >=(n)),a,b,c) +#else +#define DB_ECM(a,b,c) DB_PR((debug.d_smt&1),a,b,c) +#define DB_ECMN(n,a,b,c) DB_PR((debug.d_ecm >=(n)),a,b,c) +#define DB_RMT(a,b,c) DB_PR((debug.d_smt&2),a,b,c) +#define DB_RMTN(n,a,b,c) DB_PR((debug.d_rmt >=(n)),a,b,c) +#define DB_CFM(a,b,c) DB_PR((debug.d_smt&4),a,b,c) +#define DB_CFMN(n,a,b,c) DB_PR((debug.d_cfm >=(n)),a,b,c) +#define DB_PCM(a,b,c) DB_PR((debug.d_smt&8),a,b,c) +#define DB_PCMN(n,a,b,c) DB_PR((debug.d_pcm >=(n)),a,b,c) +#define DB_SMT(a,b,c) DB_PR((debug.d_smtf),a,b,c) +#define DB_SMTN(n,a,b,c) DB_PR((debug.d_smtf >=(n)),a,b,c) +#define DB_SBA(a,b,c) DB_PR((debug.d_sba),a,b,c) +#define DB_SBAN(n,a,b,c) DB_PR((debug.d_sba >=(n)),a,b,c) +#define DB_ESS(a,b,c) DB_PR((debug.d_ess),a,b,c) +#define DB_ESSN(n,a,b,c) DB_PR((debug.d_ess >=(n)),a,b,c) +#endif + +#ifndef SS_NOT_DS +#define SK_LOC_DECL(type,var) type var +#else +#define SK_LOC_DECL(type,var) static type var +#endif +/* + * PHYs and PORTS + * Note: Don't touch the definition of PA and PB. Those might be used + * by some "for" loops. + */ +#define PA 0 +#define PB 1 +#if defined(SUPERNET_3) || defined(CONC_II) +/* + * The port indices have to be different, + * because the MAC output goes through the 2. PLC + * Conc II: It has to be the first port in the row. + */ +#define PS 0 /* Internal PLC which is the same as PA */ +#else +#define PS 1 +#endif +#define PM 2 /* PM .. PA+NUM_PHYS-1 */ + +/* + * PHY types - as in path descriptor 'fddiPHYType' + */ +#define TA 0 /* A port */ +#define TB 1 /* B port */ +#define TS 2 /* S port */ +#define TM 3 /* M port */ +#define TNONE 4 + + +/* + * indexes in MIB + */ +#define INDEX_MAC 1 +#define INDEX_PATH 1 +#define INDEX_PORT 1 + + +/* + * policies + */ +#define POLICY_AA (1<<0) /* reject AA */ +#define POLICY_AB (1<<1) /* reject AB */ +#define POLICY_AS (1<<2) /* reject AS */ +#define POLICY_AM (1<<3) /* reject AM */ +#define POLICY_BA (1<<4) /* reject BA */ +#define POLICY_BB (1<<5) /* reject BB */ +#define POLICY_BS (1<<6) /* reject BS */ +#define POLICY_BM (1<<7) /* reject BM */ +#define POLICY_SA (1<<8) /* reject SA */ +#define POLICY_SB (1<<9) /* reject SB */ +#define POLICY_SS (1<<10) /* reject SS */ +#define POLICY_SM (1<<11) /* reject SM */ +#define POLICY_MA (1<<12) /* reject MA */ +#define POLICY_MB (1<<13) /* reject MB */ +#define POLICY_MS (1<<14) /* reject MS */ +#define POLICY_MM (1<<15) /* reject MM */ + +/* + * commands + */ + +/* + * EVENTS + * event classes + */ +#define EVENT_ECM 1 /* event class ECM */ +#define EVENT_CFM 2 /* event class CFM */ +#define EVENT_RMT 3 /* event class RMT */ +#define EVENT_SMT 4 /* event class SMT */ +#define EVENT_PCM 5 /* event class PCM */ +#define EVENT_PCMA 5 /* event class PCMA */ +#define EVENT_PCMB 6 /* event class PCMB */ + +/* WARNING : + * EVENT_PCM* must be last in the above list + * if more than two ports are used, EVENT_PCM .. EVENT_PCMA+NUM_PHYS-1 + * are used ! + */ + +#define EV_TOKEN(class,event) (((u_long)(class)<<16L)|((u_long)(event))) +#define EV_T_CLASS(token) ((int)((token)>>16)&0xffff) +#define EV_T_EVENT(token) ((int)(token)&0xffff) + +/* + * ECM events + */ +#define EC_CONNECT 1 /* connect request */ +#define EC_DISCONNECT 2 /* disconnect request */ +#define EC_TRACE_PROP 3 /* trace propagation */ +#define EC_PATH_TEST 4 /* path test */ +#define EC_TIMEOUT_TD 5 /* timer TD_min */ +#define EC_TIMEOUT_TMAX 6 /* timer trace_max */ +#define EC_TIMEOUT_IMAX 7 /* timer I_max */ +#define EC_TIMEOUT_INMAX 8 /* timer IN_max */ +#define EC_TEST_DONE 9 /* path test done */ + +/* + * CFM events + */ +#define CF_LOOP 1 /* cf_loop flag from PCM */ +#define CF_LOOP_A 1 /* cf_loop flag from PCM */ +#define CF_LOOP_B 2 /* cf_loop flag from PCM */ +#define CF_JOIN 3 /* cf_join flag from PCM */ +#define CF_JOIN_A 3 /* cf_join flag from PCM */ +#define CF_JOIN_B 4 /* cf_join flag from PCM */ + +/* + * PCM events + */ +#define PC_START 1 +#define PC_STOP 2 +#define PC_LOOP 3 +#define PC_JOIN 4 +#define PC_SIGNAL 5 +#define PC_REJECT 6 +#define PC_MAINT 7 +#define PC_TRACE 8 +#define PC_PDR 9 +#define PC_ENABLE 10 +#define PC_DISABLE 11 + +/* + * must be ordered as in LineStateType + */ +#define PC_QLS 12 +#define PC_ILS 13 +#define PC_MLS 14 +#define PC_HLS 15 +#define PC_LS_PDR 16 +#define PC_LS_NONE 17 +#define LS2MIB(x) ((x)-PC_QLS) +#define MIB2LS(x) ((x)+PC_QLS) + +#define PC_TIMEOUT_TB_MAX 18 /* timer TB_max */ +#define PC_TIMEOUT_TB_MIN 19 /* timer TB_min */ +#define PC_TIMEOUT_C_MIN 20 /* timer C_Min */ +#define PC_TIMEOUT_T_OUT 21 /* timer T_Out */ +#define PC_TIMEOUT_TL_MIN 22 /* timer TL_Min */ +#define PC_TIMEOUT_T_NEXT 23 /* timer t_next[] */ +#define PC_TIMEOUT_LCT 24 +#define PC_NSE 25 /* NOISE hardware timer */ +#define PC_LEM 26 /* LEM done */ + +/* + * RMT events meaning from + */ +#define RM_RING_OP 1 /* ring operational MAC */ +#define RM_RING_NON_OP 2 /* ring not operational MAC */ +#define RM_MY_BEACON 3 /* recvd my beacon MAC */ +#define RM_OTHER_BEACON 4 /* recvd other beacon MAC */ +#define RM_MY_CLAIM 5 /* recvd my claim MAC */ +#define RM_TRT_EXP 6 /* TRT exp MAC */ +#define RM_VALID_CLAIM 7 /* claim from dup addr MAC */ +#define RM_JOIN 8 /* signal rm_join CFM */ +#define RM_LOOP 9 /* signal rm_loop CFM */ +#define RM_DUP_ADDR 10 /* dup_addr_test hange SMT-NIF */ +#define RM_ENABLE_FLAG 11 /* enable flag */ + +#define RM_TIMEOUT_NON_OP 12 /* timeout T_Non_OP */ +#define RM_TIMEOUT_T_STUCK 13 /* timeout T_Stuck */ +#define RM_TIMEOUT_ANNOUNCE 14 /* timeout T_Announce */ +#define RM_TIMEOUT_T_DIRECT 15 /* timeout T_Direct */ +#define RM_TIMEOUT_D_MAX 16 /* timeout D_Max */ +#define RM_TIMEOUT_POLL 17 /* claim/beacon poller */ +#define RM_TX_STATE_CHANGE 18 /* To restart timer for D_Max */ + +/* + * SMT events + */ +#define SM_TIMER 1 /* timer */ +#define SM_FAST 2 /* smt_force_irq */ + +/* PC modes */ +#define PM_NONE 0 +#define PM_PEER 1 +#define PM_TREE 2 + +/* + * PCM withhold codes + * MIB PC-WithholdType ENUM + */ +#define PC_WH_NONE 0 /* ok */ +#define PC_WH_M_M 1 /* M to M */ +#define PC_WH_OTHER 2 /* other incompatible phys */ +#define PC_WH_PATH 3 /* path not available */ +/* + * LCT duration + */ +#define LC_SHORT 1 /* short LCT */ +#define LC_MEDIUM 2 /* medium LCT */ +#define LC_LONG 3 /* long LCT */ +#define LC_EXTENDED 4 /* extended LCT */ + +/* + * path_test values + */ +#define PT_NONE 0 +#define PT_TESTING 1 /* test is running */ +#define PT_PASSED 2 /* test passed */ +#define PT_FAILED 3 /* test failed */ +#define PT_PENDING 4 /* path test follows */ +#define PT_EXITING 5 /* disconnected while in trace/leave */ + +/* + * duplicate address test + * MIB DupAddressTest ENUM + */ +#define DA_NONE 0 /* */ +#define DA_PASSED 1 /* test passed */ +#define DA_FAILED 2 /* test failed */ + + +/* + * optical bypass + */ +#define BP_DEINSERT 0 /* disable bypass */ +#define BP_INSERT 1 /* enable bypass */ + +/* + * ODL enable/disable + */ +#define PM_TRANSMIT_DISABLE 0 /* disable xmit */ +#define PM_TRANSMIT_ENABLE 1 /* enable xmit */ + +/* + * parameter for config_mux + * note : number is index in config_endec table ! + */ +#define MUX_THRUA 0 /* through A */ +#define MUX_THRUB 1 /* through B */ +#define MUX_WRAPA 2 /* wrap A */ +#define MUX_WRAPB 3 /* wrap B */ +#define MUX_ISOLATE 4 /* isolated */ +#define MUX_WRAPS 5 /* SAS */ + +/* + * MAC control + */ +#define MA_RESET 0 +#define MA_BEACON 1 +#define MA_CLAIM 2 +#define MA_DIRECTED 3 /* directed beacon */ +#define MA_TREQ 4 /* change T_Req */ +#define MA_OFFLINE 5 /* switch MAC to offline */ + + +/* + * trace prop + * bit map for trace propagation + */ +#define ENTITY_MAC (NUMPHYS) +#define ENTITY_PHY(p) (p) +#define ENTITY_BIT(m) (1<<(m)) + +/* + * Resource Tag Types + */ +#define PATH_ISO 0 /* isolated */ +#define PATH_PRIM 3 /* primary path */ +#define PATH_THRU 5 /* through path */ + +#define RES_MAC 2 /* resource type MAC */ +#define RES_PORT 4 /* resource type PORT */ + + +/* + * CFM state + * oops: MUST MATCH CF-StateType in SMT7.2 ! + */ +#define SC0_ISOLATED 0 /* isolated */ +#define SC1_WRAP_A 5 /* wrap A (not used) */ +#define SC2_WRAP_B 6 /* wrap B (not used) */ +#define SC4_THRU_A 12 /* through A */ +#define SC5_THRU_B 7 /* through B (used in SMT 6.2) */ +#define SC7_WRAP_S 8 /* SAS (not used) */ +#define SC9_C_WRAP_A 9 /* c wrap A */ +#define SC10_C_WRAP_B 10 /* c wrap B */ +#define SC11_C_WRAP_S 11 /* c wrap S */ + +/* + * convert MIB time in units of 80nS to uS + */ +#define MIB2US(t) ((t)/12) +#define SEC2MIB(s) ((s)*12500000L) +/* + * SMT timer + */ +struct smt_timer { + struct smt_timer *tm_next ; /* linked list */ + struct s_smc *tm_smc ; /* pointer to context */ + u_long tm_delta ; /* delta time */ + u_long tm_token ; /* token value */ + u_short tm_active ; /* flag : active/inactive */ + u_short tm_pad ; /* pad field */ +} ; + +/* + * communication structures + */ +struct mac_parameter { + u_long t_neg ; /* T_Neg parameter */ + u_long t_pri ; /* T_Pri register in MAC */ +} ; + +/* + * MAC counters + */ +struct mac_counter { + u_long mac_nobuf_counter ; /* MAC SW counter: no buffer */ + u_long mac_r_restart_counter ; /* MAC SW counter: rx restarted */ +} ; + +/* + * para struct context for SMT parameters + */ +struct s_pcon { + int pc_len ; + int pc_err ; + int pc_badset ; + void *pc_p ; +} ; + +/* + * link error monitor + */ +#define LEM_AVG 5 +struct lem_counter { +#ifdef AM29K + int lem_on ; + u_long lem_errors ; + u_long lem_symbols ; + u_long lem_tsymbols ; + int lem_s_count ; + int lem_n_s ; + int lem_values ; + int lem_index ; + int lem_avg_ber[LEM_AVG] ; + int lem_sum ; +#else + u_short lem_float_ber ; /* 10E-nn bit error rate */ + u_long lem_errors ; /* accumulated error count */ + u_short lem_on ; +#endif +} ; + +#define NUMBITS 10 + +#ifdef AMDPLC + +/* + * PLC state table + */ +struct s_plc { + u_short p_state ; /* current state */ + u_short p_bits ; /* number of bits to send */ + u_short p_start ; /* first bit pos */ + u_short p_pad ; /* padding for alignment */ + u_long soft_err ; /* error counter */ + u_long parity_err ; /* error counter */ + u_long ebuf_err ; /* error counter */ + u_long ebuf_cont ; /* continuous error counter */ + u_long phyinv ; /* error counter */ + u_long vsym_ctr ; /* error counter */ + u_long mini_ctr ; /* error counter */ + u_long tpc_exp ; /* error counter */ + u_long np_err ; /* error counter */ + u_long b_pcs ; /* error counter */ + u_long b_tpc ; /* error counter */ + u_long b_tne ; /* error counter */ + u_long b_qls ; /* error counter */ + u_long b_ils ; /* error counter */ + u_long b_hls ; /* error counter */ +} ; +#endif + +#ifdef PROTOTYP_INC +#include "fddi/driver.pro" +#else /* PROTOTYP_INC */ +/* + * function prototypes + */ +#include "mbuf.h" /* Type definitions for MBUFs */ +#include "smtstate.h" /* struct smt_state */ + +void hwt_restart(struct s_smc *smc); /* hwt.c */ +SMbuf *smt_build_frame(struct s_smc *smc, int class, int type, + int length); /* smt.c */ +SMbuf *smt_get_mbuf(struct s_smc *smc); /* drvsr.c */ +void *sm_to_para(struct s_smc *smc, struct smt_header *sm, + int para); /* smt.c */ + +#ifndef SK_UNUSED +#define SK_UNUSED(var) (void)(var) +#endif + +void queue_event(struct s_smc *smc, int class, int event); +void ecm(struct s_smc *smc, int event); +void ecm_init(struct s_smc *smc); +void rmt(struct s_smc *smc, int event); +void rmt_init(struct s_smc *smc); +void pcm(struct s_smc *smc, const int np, int event); +void pcm_init(struct s_smc *smc); +void cfm(struct s_smc *smc, int event); +void cfm_init(struct s_smc *smc); +void smt_timer_start(struct s_smc *smc, struct smt_timer *timer, u_long time, + u_long token); +void smt_timer_stop(struct s_smc *smc, struct smt_timer *timer); +void pcm_status_state(struct s_smc *smc, int np, int *type, int *state, + int *remote, int *mac); +void plc_config_mux(struct s_smc *smc, int mux); +void sm_lem_evaluate(struct s_smc *smc); +void mac_update_counter(struct s_smc *smc); +void sm_pm_ls_latch(struct s_smc *smc, int phy, int on_off); +void sm_ma_control(struct s_smc *smc, int mode); +void sm_mac_check_beacon_claim(struct s_smc *smc); +void config_mux(struct s_smc *smc, int mux); +void smt_agent_init(struct s_smc *smc); +void smt_timer_init(struct s_smc *smc); +void smt_received_pack(struct s_smc *smc, SMbuf *mb, int fs); +void smt_add_para(struct s_smc *smc, struct s_pcon *pcon, u_short para, + int index, int local); +void smt_swap_para(struct smt_header *sm, int len, int direction); +void ev_init(struct s_smc *smc); +void hwt_init(struct s_smc *smc); +u_long hwt_read(struct s_smc *smc); +void hwt_stop(struct s_smc *smc); +void hwt_start(struct s_smc *smc, u_long time); +void smt_send_mbuf(struct s_smc *smc, SMbuf *mb, int fc); +void smt_free_mbuf(struct s_smc *smc, SMbuf *mb); +void sm_pm_bypass_req(struct s_smc *smc, int mode); +void rmt_indication(struct s_smc *smc, int i); +void cfm_state_change(struct s_smc *smc, int c_state); + +#if defined(DEBUG) || !defined(NO_SMT_PANIC) +void smt_panic(struct s_smc *smc, char *text); +#else +#define smt_panic(smc,text) +#endif /* DEBUG || !NO_SMT_PANIC */ + +void smt_stat_counter(struct s_smc *smc, int stat); +void smt_timer_poll(struct s_smc *smc); +u_long smt_get_time(void); +u_long smt_get_tid(struct s_smc *smc); +void smt_timer_done(struct s_smc *smc); +void smt_fixup_mib(struct s_smc *smc); +void smt_reset_defaults(struct s_smc *smc, int level); +void smt_agent_task(struct s_smc *smc); +int smt_check_para(struct s_smc *smc, struct smt_header *sm, + const u_short list[]); +void driver_get_bia(struct s_smc *smc, struct fddi_addr *bia_addr); + +#ifdef SUPERNET_3 +void drv_reset_indication(struct s_smc *smc); +#endif /* SUPERNET_3 */ + +void smt_start_watchdog(struct s_smc *smc); +void smt_event(struct s_smc *smc, int event); +void timer_event(struct s_smc *smc, u_long token); +void ev_dispatcher(struct s_smc *smc); +void pcm_get_state(struct s_smc *smc, struct smt_state *state); +void ecm_state_change(struct s_smc *smc, int e_state); +int sm_pm_bypass_present(struct s_smc *smc); +void pcm_state_change(struct s_smc *smc, int plc, int p_state); +void rmt_state_change(struct s_smc *smc, int r_state); +int sm_pm_get_ls(struct s_smc *smc, int phy); +int pcm_get_s_port(struct s_smc *smc); +int pcm_rooted_station(struct s_smc *smc); +int cfm_get_mac_input(struct s_smc *smc); +int cfm_get_mac_output(struct s_smc *smc); +int cem_build_path(struct s_smc *smc, char *to, int path_index); +int sm_mac_get_tx_state(struct s_smc *smc); +char *get_pcmstate(struct s_smc *smc, int np); +int smt_action(struct s_smc *smc, int class, int code, int index); +u_short smt_online(struct s_smc *smc, int on); +void smt_force_irq(struct s_smc *smc); +void smt_pmf_received_pack(struct s_smc *smc, SMbuf *mb, int local); +void smt_send_frame(struct s_smc *smc, SMbuf *mb, int fc, int local); +void smt_set_timestamp(struct s_smc *smc, u_char *p); +void mac_set_rx_mode(struct s_smc *smc, int mode); +int mac_add_multicast(struct s_smc *smc, struct fddi_addr *addr, int can); +void mac_update_multicast(struct s_smc *smc); +void mac_clear_multicast(struct s_smc *smc); +void set_formac_tsync(struct s_smc *smc, long sync_bw); +void formac_reinit_tx(struct s_smc *smc); +void formac_tx_restart(struct s_smc *smc); +void process_receive(struct s_smc *smc); +void init_driver_fplus(struct s_smc *smc); +void rtm_irq(struct s_smc *smc); +void rtm_set_timer(struct s_smc *smc); +void ring_status_indication(struct s_smc *smc, u_long status); +void llc_recover_tx(struct s_smc *smc); +void llc_restart_tx(struct s_smc *smc); +void plc_clear_irq(struct s_smc *smc, int p); +void plc_irq(struct s_smc *smc, int np, unsigned int cmd); +int smt_set_mac_opvalues(struct s_smc *smc); + +#ifdef TAG_MODE +void mac_do_pci_fix(struct s_smc *smc); +void mac_drv_clear_tx_queue(struct s_smc *smc); +void mac_drv_repair_descr(struct s_smc *smc); +u_long hwt_quick_read(struct s_smc *smc); +void hwt_wait_time(struct s_smc *smc, u_long start, long duration); +#endif + +#ifdef SMT_PNMI +int pnmi_init(struct s_smc* smc); +int pnmi_process_ndis_id(struct s_smc *smc, u_long ndis_oid, void *buf, int len, + int *BytesAccessed, int *BytesNeeded, u_char action); +#endif + +#ifdef SBA +#ifndef _H2INC +void sba(); +#endif +void sba_raf_received_pack(); +void sba_timer_poll(); +void smt_init_sba(); +#endif + +#ifdef ESS +int ess_raf_received_pack(struct s_smc *smc, SMbuf *mb, struct smt_header *sm, + int fs); +void ess_timer_poll(struct s_smc *smc); +void ess_para_change(struct s_smc *smc); +#endif + +#ifndef BOOT +void smt_init_evc(struct s_smc *smc); +void smt_srf_event(struct s_smc *smc, int code, int index, int cond); +#else +#define smt_init_evc(smc) +#define smt_srf_event(smc,code,index,cond) +#endif + +#ifndef SMT_REAL_TOKEN_CT +void smt_emulate_token_ct(struct s_smc *smc, int mac_index); +#endif + +#if defined(DEBUG) && !defined(BOOT) +void dump_smt(struct s_smc *smc, struct smt_header *sm, char *text); +#else +#define dump_smt(smc,sm,text) +#endif + +#ifdef DEBUG +char* addr_to_string(struct fddi_addr *addr); +void dump_hex(char *p, int len); +#endif + +#endif /* PROTOTYP_INC */ + +/* PNMI default defines */ +#ifndef PNMI_INIT +#define PNMI_INIT(smc) /* Nothing */ +#endif +#ifndef PNMI_GET_ID +#define PNMI_GET_ID( smc, ndis_oid, buf, len, BytesWritten, BytesNeeded ) \ + ( 1 ? (-1) : (-1) ) +#endif +#ifndef PNMI_SET_ID +#define PNMI_SET_ID( smc, ndis_oid, buf, len, BytesRead, BytesNeeded, \ + set_type) ( 1 ? (-1) : (-1) ) +#endif + +/* + * SMT_PANIC defines + */ +#ifndef SMT_PANIC +#define SMT_PANIC(smc,nr,msg) smt_panic (smc, msg) +#endif + +#ifndef SMT_ERR_LOG +#define SMT_ERR_LOG(smc,nr,msg) SMT_PANIC (smc, nr, msg) +#endif + +#ifndef SMT_EBASE +#define SMT_EBASE 100 +#endif + +#define SMT_E0100 SMT_EBASE + 0 +#define SMT_E0100_MSG "cfm FSM: invalid ce_type" +#define SMT_E0101 SMT_EBASE + 1 +#define SMT_E0101_MSG "CEM: case ???" +#define SMT_E0102 SMT_EBASE + 2 +#define SMT_E0102_MSG "CEM A: invalid state" +#define SMT_E0103 SMT_EBASE + 3 +#define SMT_E0103_MSG "CEM B: invalid state" +#define SMT_E0104 SMT_EBASE + 4 +#define SMT_E0104_MSG "CEM M: invalid state" +#define SMT_E0105 SMT_EBASE + 5 +#define SMT_E0105_MSG "CEM S: invalid state" +#define SMT_E0106 SMT_EBASE + 6 +#define SMT_E0106_MSG "CFM : invalid state" +#define SMT_E0107 SMT_EBASE + 7 +#define SMT_E0107_MSG "ECM : invalid state" +#define SMT_E0108 SMT_EBASE + 8 +#define SMT_E0108_MSG "prop_actions : NAC in DAS CFM" +#define SMT_E0109 SMT_EBASE + 9 +#define SMT_E0109_MSG "ST2U.FM_SERRSF error in special frame" +#define SMT_E0110 SMT_EBASE + 10 +#define SMT_E0110_MSG "ST2U.FM_SRFRCTOV recv. count. overflow" +#define SMT_E0111 SMT_EBASE + 11 +#define SMT_E0111_MSG "ST2U.FM_SNFSLD NP & FORMAC simult. load" +#define SMT_E0112 SMT_EBASE + 12 +#define SMT_E0112_MSG "ST2U.FM_SRCVFRM single-frame recv.-mode" +#define SMT_E0113 SMT_EBASE + 13 +#define SMT_E0113_MSG "FPLUS: Buffer Memory Error" +#define SMT_E0114 SMT_EBASE + 14 +#define SMT_E0114_MSG "ST2U.FM_SERRSF error in special frame" +#define SMT_E0115 SMT_EBASE + 15 +#define SMT_E0115_MSG "ST3L: parity error in receive queue 2" +#define SMT_E0116 SMT_EBASE + 16 +#define SMT_E0116_MSG "ST3L: parity error in receive queue 1" +#define SMT_E0117 SMT_EBASE + 17 +#define SMT_E0117_MSG "E_SMT_001: RxD count for receive queue 1 = 0" +#define SMT_E0118 SMT_EBASE + 18 +#define SMT_E0118_MSG "PCM : invalid state" +#define SMT_E0119 SMT_EBASE + 19 +#define SMT_E0119_MSG "smt_add_para" +#define SMT_E0120 SMT_EBASE + 20 +#define SMT_E0120_MSG "smt_set_para" +#define SMT_E0121 SMT_EBASE + 21 +#define SMT_E0121_MSG "invalid event in dispatcher" +#define SMT_E0122 SMT_EBASE + 22 +#define SMT_E0122_MSG "RMT : invalid state" +#define SMT_E0123 SMT_EBASE + 23 +#define SMT_E0123_MSG "SBA: state machine has invalid state" +#define SMT_E0124 SMT_EBASE + 24 +#define SMT_E0124_MSG "sba_free_session() called with NULL pointer" +#define SMT_E0125 SMT_EBASE + 25 +#define SMT_E0125_MSG "SBA : invalid session pointer" +#define SMT_E0126 SMT_EBASE + 26 +#define SMT_E0126_MSG "smt_free_mbuf() called with NULL pointer\n" +#define SMT_E0127 SMT_EBASE + 27 +#define SMT_E0127_MSG "sizeof evcs" +#define SMT_E0128 SMT_EBASE + 28 +#define SMT_E0128_MSG "evc->evc_cond_state = 0" +#define SMT_E0129 SMT_EBASE + 29 +#define SMT_E0129_MSG "evc->evc_multiple = 0" +#define SMT_E0130 SMT_EBASE + 30 +#define SMT_E0130_MSG write_mdr_warning +#define SMT_E0131 SMT_EBASE + 31 +#define SMT_E0131_MSG cam_warning +#define SMT_E0132 SMT_EBASE + 32 +#define SMT_E0132_MSG "ST1L.FM_SPCEPDx parity/coding error" +#define SMT_E0133 SMT_EBASE + 33 +#define SMT_E0133_MSG "ST1L.FM_STBURx tx buffer underrun" +#define SMT_E0134 SMT_EBASE + 34 +#define SMT_E0134_MSG "ST1L.FM_SPCEPDx parity error" +#define SMT_E0135 SMT_EBASE + 35 +#define SMT_E0135_MSG "RMT: duplicate MAC address detected. Ring left!" +#define SMT_E0136 SMT_EBASE + 36 +#define SMT_E0136_MSG "Elasticity Buffer hang-up" +#define SMT_E0137 SMT_EBASE + 37 +#define SMT_E0137_MSG "SMT: queue overrun" +#define SMT_E0138 SMT_EBASE + 38 +#define SMT_E0138_MSG "RMT: duplicate MAC address detected. Ring NOT left!" +#endif /* _CMTDEF_ */ diff --git a/kernel/drivers/net/fddi/skfp/h/fddi.h b/kernel/drivers/net/fddi/skfp/h/fddi.h new file mode 100644 index 000000000..c9a28a8a3 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/fddi.h @@ -0,0 +1,69 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _FDDI_ +#define _FDDI_ + +struct fddi_addr { + u_char a[6] ; +} ; + +#define GROUP_ADDR 0x80 /* MSB in a[0] */ + +struct fddi_mac { + struct fddi_addr mac_dest ; + struct fddi_addr mac_source ; + u_char mac_info[4478] ; +} ; + +#define FDDI_MAC_SIZE (12) +#define FDDI_RAW_MTU (4500-5) /* exl. Pr,SD, ED/FS */ +#define FDDI_RAW (4500) + +/* + * FC values + */ +#define FC_VOID 0x40 /* void frame */ +#define FC_TOKEN 0x80 /* token */ +#define FC_RES_TOKEN 0xc0 /* restricted token */ +#define FC_SMT_INFO 0x41 /* SMT Info frame */ +/* + * FC_SMT_LAN_LOC && FC_SMT_LOC are SK specific ! + */ +#define FC_SMT_LAN_LOC 0x42 /* local SMT Info frame */ +#define FC_SMT_LOC 0x43 /* local SMT Info frame */ +#define FC_SMT_NSA 0x4f /* SMT NSA frame */ +#define FC_MAC 0xc0 /* MAC frame */ +#define FC_BEACON 0xc2 /* MAC beacon frame */ +#define FC_CLAIM 0xc3 /* MAC claim frame */ +#define FC_SYNC_LLC 0xd0 /* sync. LLC frame */ +#define FC_ASYNC_LLC 0x50 /* async. LLC frame */ +#define FC_SYNC_BIT 0x80 /* sync. bit in FC */ + +#define FC_LLC_PRIOR 0x07 /* priority bits */ + +#define BEACON_INFO 0 /* beacon type */ +#define DBEACON_INFO 1 /* beacon type DIRECTED */ + + +/* + * indicator bits + */ +#define C_INDICATOR (1<<0) +#define A_INDICATOR (1<<1) +#define E_INDICATOR (1<<2) +#define I_INDICATOR (1<<6) /* SK specific */ +#define L_INDICATOR (1<<7) /* SK specific */ + +#endif /* _FDDI_ */ diff --git a/kernel/drivers/net/fddi/skfp/h/fddimib.h b/kernel/drivers/net/fddi/skfp/h/fddimib.h new file mode 100644 index 000000000..d1acdc773 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/fddimib.h @@ -0,0 +1,349 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * FDDI MIB + */ + +/* + * typedefs + */ + +typedef u_long Counter ; +typedef u_char TimeStamp[8] ; +typedef struct fddi_addr LongAddr ; +typedef u_long Timer_2 ; +typedef u_long Timer ; +typedef u_short ResId ; +typedef u_short SMTEnum ; +typedef u_char SMTFlag ; + +typedef struct { + Counter count ; + TimeStamp timestamp ; +} SetCountType ; + +/* + * bits for bit string "available_path" + */ +#define MIB_PATH_P (1<<0) +#define MIB_PATH_S (1<<1) +#define MIB_PATH_L (1<<2) + +/* + * bits for bit string PermittedPaths & RequestedPaths (SIZE(8)) + */ +#define MIB_P_PATH_LOCAL (1<<0) +#define MIB_P_PATH_SEC_ALTER (1<<1) +#define MIB_P_PATH_PRIM_ALTER (1<<2) +#define MIB_P_PATH_CON_ALTER (1<<3) +#define MIB_P_PATH_SEC_PREFER (1<<4) +#define MIB_P_PATH_PRIM_PREFER (1<<5) +#define MIB_P_PATH_CON_PREFER (1<<6) +#define MIB_P_PATH_THRU (1<<7) + +/* + * enum current path + */ +#define MIB_PATH_ISOLATED 0 +#define MIB_PATH_LOCAL 1 +#define MIB_PATH_SECONDARY 2 +#define MIB_PATH_PRIMARY 3 +#define MIB_PATH_CONCATENATED 4 +#define MIB_PATH_THRU 5 + +/* + * enum PMDClass + */ +#define MIB_PMDCLASS_MULTI 0 +#define MIB_PMDCLASS_SINGLE1 1 +#define MIB_PMDCLASS_SINGLE2 2 +#define MIB_PMDCLASS_SONET 3 +#define MIB_PMDCLASS_LCF 4 +#define MIB_PMDCLASS_TP 5 +#define MIB_PMDCLASS_UNKNOWN 6 +#define MIB_PMDCLASS_UNSPEC 7 + +/* + * enum SMTStationStatus + */ +#define MIB_SMT_STASTA_CON 0 +#define MIB_SMT_STASTA_SEPA 1 +#define MIB_SMT_STASTA_THRU 2 + + +struct fddi_mib { + /* + * private + */ + u_char fddiPRPMFPasswd[8] ; + struct smt_sid fddiPRPMFStation ; + +#ifdef ESS + /* + * private variables for static allocation of the + * End Station Support + */ + u_long fddiESSPayload ; /* payload for static alloc */ + u_long fddiESSOverhead ; /* frame ov for static alloc */ + u_long fddiESSMaxTNeg ; /* maximum of T-NEG */ + u_long fddiESSMinSegmentSize ; /* min size of the sync frames */ + u_long fddiESSCategory ; /* category for the Alloc req */ + short fddiESSSynchTxMode ; /* send all LLC frames as sync */ +#endif /* ESS */ +#ifdef SBA + /* + * private variables for the Synchronous Bandwidth Allocator + */ + char fddiSBACommand ; /* holds the parsed SBA cmd */ + u_char fddiSBAAvailable ; /* SBA allocatable value */ +#endif /* SBA */ + + /* + * SMT standard mib + */ + struct smt_sid fddiSMTStationId ; + u_short fddiSMTOpVersionId ; + u_short fddiSMTHiVersionId ; + u_short fddiSMTLoVersionId ; + u_char fddiSMTManufacturerData[32] ; + u_char fddiSMTUserData[32] ; + u_short fddiSMTMIBVersionId ; + + /* + * ConfigGrp + */ + u_char fddiSMTMac_Ct ; + u_char fddiSMTNonMaster_Ct ; + u_char fddiSMTMaster_Ct ; + u_char fddiSMTAvailablePaths ; + u_short fddiSMTConfigCapabilities ; + u_short fddiSMTConfigPolicy ; + u_short fddiSMTConnectionPolicy ; + u_short fddiSMTTT_Notify ; + u_char fddiSMTStatRptPolicy ; + u_long fddiSMTTrace_MaxExpiration ; + u_short fddiSMTPORTIndexes[NUMPHYS] ; + u_short fddiSMTMACIndexes ; + u_char fddiSMTBypassPresent ; + + /* + * StatusGrp + */ + SMTEnum fddiSMTECMState ; + SMTEnum fddiSMTCF_State ; + SMTEnum fddiSMTStationStatus ; + u_char fddiSMTRemoteDisconnectFlag ; + u_char fddiSMTPeerWrapFlag ; + + /* + * MIBOperationGrp + */ + TimeStamp fddiSMTTimeStamp ; + TimeStamp fddiSMTTransitionTimeStamp ; + SetCountType fddiSMTSetCount ; + struct smt_sid fddiSMTLastSetStationId ; + + struct fddi_mib_m { + u_short fddiMACFrameStatusFunctions ; + Timer_2 fddiMACT_MaxCapabilitiy ; + Timer_2 fddiMACTVXCapabilitiy ; + + /* ConfigGrp */ + u_char fddiMACMultiple_N ; /* private */ + u_char fddiMACMultiple_P ; /* private */ + u_char fddiMACDuplicateAddressCond ;/* private */ + u_char fddiMACAvailablePaths ; + u_short fddiMACCurrentPath ; + LongAddr fddiMACUpstreamNbr ; + LongAddr fddiMACDownstreamNbr ; + LongAddr fddiMACOldUpstreamNbr ; + LongAddr fddiMACOldDownstreamNbr ; + SMTEnum fddiMACDupAddressTest ; + u_short fddiMACRequestedPaths ; + SMTEnum fddiMACDownstreamPORTType ; + ResId fddiMACIndex ; + + /* AddressGrp */ + LongAddr fddiMACSMTAddress ; + + /* OperationGrp */ + Timer_2 fddiMACT_Min ; /* private */ + Timer_2 fddiMACT_ReqMIB ; + Timer_2 fddiMACT_Req ; /* private */ + Timer_2 fddiMACT_Neg ; + Timer_2 fddiMACT_MaxMIB ; + Timer_2 fddiMACT_Max ; /* private */ + Timer_2 fddiMACTvxValueMIB ; + Timer_2 fddiMACTvxValue ; /* private */ + Timer_2 fddiMACT_Pri0 ; + Timer_2 fddiMACT_Pri1 ; + Timer_2 fddiMACT_Pri2 ; + Timer_2 fddiMACT_Pri3 ; + Timer_2 fddiMACT_Pri4 ; + Timer_2 fddiMACT_Pri5 ; + Timer_2 fddiMACT_Pri6 ; + + /* CountersGrp */ + Counter fddiMACFrame_Ct ; + Counter fddiMACCopied_Ct ; + Counter fddiMACTransmit_Ct ; + Counter fddiMACToken_Ct ; + Counter fddiMACError_Ct ; + Counter fddiMACLost_Ct ; + Counter fddiMACTvxExpired_Ct ; + Counter fddiMACNotCopied_Ct ; + Counter fddiMACRingOp_Ct ; + + Counter fddiMACSMTCopied_Ct ; /* private */ + Counter fddiMACSMTTransmit_Ct ; /* private */ + + /* private for delta ratio */ + Counter fddiMACOld_Frame_Ct ; + Counter fddiMACOld_Copied_Ct ; + Counter fddiMACOld_Error_Ct ; + Counter fddiMACOld_Lost_Ct ; + Counter fddiMACOld_NotCopied_Ct ; + + /* FrameErrorConditionGrp */ + u_short fddiMACFrameErrorThreshold ; + u_short fddiMACFrameErrorRatio ; + + /* NotCopiedConditionGrp */ + u_short fddiMACNotCopiedThreshold ; + u_short fddiMACNotCopiedRatio ; + + /* StatusGrp */ + SMTEnum fddiMACRMTState ; + SMTFlag fddiMACDA_Flag ; + SMTFlag fddiMACUNDA_Flag ; + SMTFlag fddiMACFrameErrorFlag ; + SMTFlag fddiMACNotCopiedFlag ; + SMTFlag fddiMACMA_UnitdataAvailable ; + SMTFlag fddiMACHardwarePresent ; + SMTFlag fddiMACMA_UnitdataEnable ; + + } m[NUMMACS] ; +#define MAC0 0 + + struct fddi_mib_a { + ResId fddiPATHIndex ; + u_long fddiPATHSbaPayload ; + u_long fddiPATHSbaOverhead ; + /* fddiPATHConfiguration is built on demand */ + /* u_long fddiPATHConfiguration ; */ + Timer fddiPATHT_Rmode ; + u_long fddiPATHSbaAvailable ; + Timer_2 fddiPATHTVXLowerBound ; + Timer_2 fddiPATHT_MaxLowerBound ; + Timer_2 fddiPATHMaxT_Req ; + } a[NUMPATHS] ; +#define PATH0 0 + + struct fddi_mib_p { + /* ConfigGrp */ + SMTEnum fddiPORTMy_Type ; + SMTEnum fddiPORTNeighborType ; + u_char fddiPORTConnectionPolicies ; + struct { + u_char T_val ; + u_char R_val ; + } fddiPORTMacIndicated ; + SMTEnum fddiPORTCurrentPath ; + /* must be 4: is 32 bit in SMT format + * indices : + * 1 none + * 2 tree + * 3 peer + */ + u_char fddiPORTRequestedPaths[4] ; + u_short fddiPORTMACPlacement ; + u_char fddiPORTAvailablePaths ; + u_char fddiPORTConnectionCapabilities ; + SMTEnum fddiPORTPMDClass ; + ResId fddiPORTIndex ; + + /* OperationGrp */ + SMTEnum fddiPORTMaint_LS ; + SMTEnum fddiPORTPC_LS ; + u_char fddiPORTBS_Flag ; + + /* ErrorCtrsGrp */ + Counter fddiPORTLCTFail_Ct ; + Counter fddiPORTEBError_Ct ; + Counter fddiPORTOldEBError_Ct ; + + /* LerGrp */ + Counter fddiPORTLem_Reject_Ct ; + Counter fddiPORTLem_Ct ; + u_char fddiPORTLer_Estimate ; + u_char fddiPORTLer_Cutoff ; + u_char fddiPORTLer_Alarm ; + + /* StatusGrp */ + SMTEnum fddiPORTConnectState ; + SMTEnum fddiPORTPCMState ; /* real value */ + SMTEnum fddiPORTPCMStateX ; /* value for MIB */ + SMTEnum fddiPORTPC_Withhold ; + SMTFlag fddiPORTHardwarePresent ; + u_char fddiPORTLerFlag ; + + u_char fddiPORTMultiple_U ; /* private */ + u_char fddiPORTMultiple_P ; /* private */ + u_char fddiPORTEB_Condition ; /* private */ + } p[NUMPHYS] ; + struct { + Counter fddiPRIVECF_Req_Rx ; /* ECF req received */ + Counter fddiPRIVECF_Reply_Rx ; /* ECF repl received */ + Counter fddiPRIVECF_Req_Tx ; /* ECF req transm */ + Counter fddiPRIVECF_Reply_Tx ; /* ECF repl transm */ + Counter fddiPRIVPMF_Get_Rx ; /* PMF Get rec */ + Counter fddiPRIVPMF_Set_Rx ; /* PMF Set rec */ + Counter fddiPRIVRDF_Rx ; /* RDF received */ + Counter fddiPRIVRDF_Tx ; /* RDF transmitted */ + } priv ; +} ; + +/* + * OIDs for statistics + */ +#define SMT_OID_CF_STATE 1 /* fddiSMTCF_State */ +#define SMT_OID_PCM_STATE_A 2 /* fddiPORTPCMState port A */ +#define SMT_OID_PCM_STATE_B 17 /* fddiPORTPCMState port B */ +#define SMT_OID_RMT_STATE 3 /* fddiMACRMTState */ +#define SMT_OID_UNA 4 /* fddiMACUpstreamNbr */ +#define SMT_OID_DNA 5 /* fddiMACOldDownstreamNbr */ +#define SMT_OID_ERROR_CT 6 /* fddiMACError_Ct */ +#define SMT_OID_LOST_CT 7 /* fddiMACLost_Ct */ +#define SMT_OID_LEM_CT 8 /* fddiPORTLem_Ct */ +#define SMT_OID_LEM_CT_A 11 /* fddiPORTLem_Ct port A */ +#define SMT_OID_LEM_CT_B 12 /* fddiPORTLem_Ct port B */ +#define SMT_OID_LCT_FAIL_CT 9 /* fddiPORTLCTFail_Ct */ +#define SMT_OID_LCT_FAIL_CT_A 13 /* fddiPORTLCTFail_Ct port A */ +#define SMT_OID_LCT_FAIL_CT_B 14 /* fddiPORTLCTFail_Ct port B */ +#define SMT_OID_LEM_REJECT_CT 10 /* fddiPORTLem_Reject_Ct */ +#define SMT_OID_LEM_REJECT_CT_A 15 /* fddiPORTLem_Reject_Ct port A */ +#define SMT_OID_LEM_REJECT_CT_B 16 /* fddiPORTLem_Reject_Ct port B */ + +/* + * SK MIB + */ +#define SMT_OID_ECF_REQ_RX 20 /* ECF requests received */ +#define SMT_OID_ECF_REPLY_RX 21 /* ECF replies received */ +#define SMT_OID_ECF_REQ_TX 22 /* ECF requests transmitted */ +#define SMT_OID_ECF_REPLY_TX 23 /* ECF replies transmitted */ +#define SMT_OID_PMF_GET_RX 24 /* PMF get requests received */ +#define SMT_OID_PMF_SET_RX 25 /* PMF set requests received */ +#define SMT_OID_RDF_RX 26 /* RDF received */ +#define SMT_OID_RDF_TX 27 /* RDF transmitted */ diff --git a/kernel/drivers/net/fddi/skfp/h/fplustm.h b/kernel/drivers/net/fddi/skfp/h/fplustm.h new file mode 100644 index 000000000..d43191ed9 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/fplustm.h @@ -0,0 +1,274 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * AMD Fplus in tag mode data structs + * defs for fplustm.c + */ + +#ifndef _FPLUS_ +#define _FPLUS_ + +#ifndef HW_PTR +#define HW_PTR void __iomem * +#endif + +/* + * fplus error statistic structure + */ +struct err_st { + u_long err_valid ; /* memory status valid */ + u_long err_abort ; /* memory status receive abort */ + u_long err_e_indicator ; /* error indicator */ + u_long err_crc ; /* error detected (CRC or length) */ + u_long err_llc_frame ; /* LLC frame */ + u_long err_mac_frame ; /* MAC frame */ + u_long err_smt_frame ; /* SMT frame */ + u_long err_imp_frame ; /* implementer frame */ + u_long err_no_buf ; /* no buffer available */ + u_long err_too_long ; /* longer than max. buffer */ + u_long err_bec_stat ; /* beacon state entered */ + u_long err_clm_stat ; /* claim state entered */ + u_long err_sifg_det ; /* short interframe gap detect */ + u_long err_phinv ; /* PHY invalid */ + u_long err_tkiss ; /* token issued */ + u_long err_tkerr ; /* token error */ +} ; + +/* + * Transmit Descriptor struct + */ +struct s_smt_fp_txd { + __le32 txd_tbctrl ; /* transmit buffer control */ + __le32 txd_txdscr ; /* transmit frame status word */ + __le32 txd_tbadr ; /* physical tx buffer address */ + __le32 txd_ntdadr ; /* physical pointer to the next TxD */ +#ifdef ENA_64BIT_SUP + __le32 txd_tbadr_hi ; /* physical tx buffer addr (high dword)*/ +#endif + char far *txd_virt ; /* virtual pointer to the data frag */ + /* virt pointer to the next TxD */ + struct s_smt_fp_txd volatile far *txd_next ; + struct s_txd_os txd_os ; /* OS - specific struct */ +} ; + +/* + * Receive Descriptor struct + */ +struct s_smt_fp_rxd { + __le32 rxd_rbctrl ; /* receive buffer control */ + __le32 rxd_rfsw ; /* receive frame status word */ + __le32 rxd_rbadr ; /* physical rx buffer address */ + __le32 rxd_nrdadr ; /* physical pointer to the next RxD */ +#ifdef ENA_64BIT_SUP + __le32 rxd_rbadr_hi ; /* physical tx buffer addr (high dword)*/ +#endif + char far *rxd_virt ; /* virtual pointer to the data frag */ + /* virt pointer to the next RxD */ + struct s_smt_fp_rxd volatile far *rxd_next ; + struct s_rxd_os rxd_os ; /* OS - specific struct */ +} ; + +/* + * Descriptor Union Definition + */ +union s_fp_descr { + struct s_smt_fp_txd t ; /* pointer to the TxD */ + struct s_smt_fp_rxd r ; /* pointer to the RxD */ +} ; + +/* + * TxD Ring Control struct + */ +struct s_smt_tx_queue { + struct s_smt_fp_txd volatile *tx_curr_put ; /* next free TxD */ + struct s_smt_fp_txd volatile *tx_prev_put ; /* shadow put pointer */ + struct s_smt_fp_txd volatile *tx_curr_get ; /* next TxD to release*/ + u_short tx_free ; /* count of free TxD's */ + u_short tx_used ; /* count of used TxD's */ + HW_PTR tx_bmu_ctl ; /* BMU addr for tx start */ + HW_PTR tx_bmu_dsc ; /* BMU addr for curr dsc. */ +} ; + +/* + * RxD Ring Control struct + */ +struct s_smt_rx_queue { + struct s_smt_fp_rxd volatile *rx_curr_put ; /* next RxD to queue into */ + struct s_smt_fp_rxd volatile *rx_prev_put ; /* shadow put pointer */ + struct s_smt_fp_rxd volatile *rx_curr_get ; /* next RxD to fill */ + u_short rx_free ; /* count of free RxD's */ + u_short rx_used ; /* count of used RxD's */ + HW_PTR rx_bmu_ctl ; /* BMU addr for rx start */ + HW_PTR rx_bmu_dsc ; /* BMU addr for curr dsc. */ +} ; + +#define VOID_FRAME_OFF 0x00 +#define CLAIM_FRAME_OFF 0x08 +#define BEACON_FRAME_OFF 0x10 +#define DBEACON_FRAME_OFF 0x18 +#define RX_FIFO_OFF 0x21 /* to get a prime number for */ + /* the RX_FIFO_SPACE */ + +#define RBC_MEM_SIZE 0x8000 +#define SEND_ASYNC_AS_SYNC 0x1 +#define SYNC_TRAFFIC_ON 0x2 + +/* big FIFO memory */ +#define RX_FIFO_SPACE 0x4000 - RX_FIFO_OFF +#define TX_FIFO_SPACE 0x4000 + +#define TX_SMALL_FIFO 0x0900 +#define TX_MEDIUM_FIFO TX_FIFO_SPACE / 2 +#define TX_LARGE_FIFO TX_FIFO_SPACE - TX_SMALL_FIFO + +#define RX_SMALL_FIFO 0x0900 +#define RX_LARGE_FIFO RX_FIFO_SPACE - RX_SMALL_FIFO + +struct s_smt_fifo_conf { + u_short rbc_ram_start ; /* FIFO start address */ + u_short rbc_ram_end ; /* FIFO size */ + u_short rx1_fifo_start ; /* rx queue start address */ + u_short rx1_fifo_size ; /* rx queue size */ + u_short rx2_fifo_start ; /* rx queue start address */ + u_short rx2_fifo_size ; /* rx queue size */ + u_short tx_s_start ; /* sync queue start address */ + u_short tx_s_size ; /* sync queue size */ + u_short tx_a0_start ; /* async queue A0 start address */ + u_short tx_a0_size ; /* async queue A0 size */ + u_short fifo_config_mode ; /* FIFO configuration mode */ +} ; + +#define FM_ADDRX (FM_ADDET|FM_EXGPA0|FM_EXGPA1) + +struct s_smt_fp { + u_short mdr2init ; /* mode register 2 init value */ + u_short mdr3init ; /* mode register 3 init value */ + u_short frselreg_init ; /* frame selection register init val */ + u_short rx_mode ; /* address mode broad/multi/promisc */ + u_short nsa_mode ; + u_short rx_prom ; + u_short exgpa ; + + struct err_st err_stats ; /* error statistics */ + + /* + * MAC buffers + */ + struct fddi_mac_sf { /* special frame build buffer */ + u_char mac_fc ; + struct fddi_addr mac_dest ; + struct fddi_addr mac_source ; + u_char mac_info[0x20] ; + } mac_sfb ; + + + /* + * queues + */ +#define QUEUE_S 0 +#define QUEUE_A0 1 +#define QUEUE_R1 0 +#define QUEUE_R2 1 +#define USED_QUEUES 2 + + /* + * queue pointers; points to the queue dependent variables + */ + struct s_smt_tx_queue *tx[USED_QUEUES] ; + struct s_smt_rx_queue *rx[USED_QUEUES] ; + + /* + * queue dependent variables + */ + struct s_smt_tx_queue tx_q[USED_QUEUES] ; + struct s_smt_rx_queue rx_q[USED_QUEUES] ; + + /* + * FIFO configuration struct + */ + struct s_smt_fifo_conf fifo ; + + /* last formac status */ + u_short s2u ; + u_short s2l ; + + /* calculated FORMAC+ reg.addr. */ + HW_PTR fm_st1u ; + HW_PTR fm_st1l ; + HW_PTR fm_st2u ; + HW_PTR fm_st2l ; + HW_PTR fm_st3u ; + HW_PTR fm_st3l ; + + + /* + * multicast table + */ +#define FPMAX_MULTICAST 32 +#define SMT_MAX_MULTI 4 + struct { + struct s_fpmc { + struct fddi_addr a ; /* mc address */ + u_char n ; /* usage counter */ + u_char perm ; /* flag: permanent */ + } table[FPMAX_MULTICAST] ; + } mc ; + struct fddi_addr group_addr ; + u_long func_addr ; /* functional address */ + int smt_slots_used ; /* count of table entries for the SMT */ + int os_slots_used ; /* count of table entries */ + /* used by the os-specific module */ +} ; + +/* + * modes for mac_set_rx_mode() + */ +#define RX_ENABLE_ALLMULTI 1 /* enable all multicasts */ +#define RX_DISABLE_ALLMULTI 2 /* disable "enable all multicasts" */ +#define RX_ENABLE_PROMISC 3 /* enable promiscuous */ +#define RX_DISABLE_PROMISC 4 /* disable promiscuous */ +#define RX_ENABLE_NSA 5 /* enable reception of NSA frames */ +#define RX_DISABLE_NSA 6 /* disable reception of NSA frames */ + + +/* + * support for byte reversal in AIX + * (descriptors and pointers must be byte reversed in memory + * CPU is big endian; M-Channel is little endian) + */ +#ifdef AIX +#define MDR_REV +#define AIX_REVERSE(x) ((((x)<<24L)&0xff000000L) + \ + (((x)<< 8L)&0x00ff0000L) + \ + (((x)>> 8L)&0x0000ff00L) + \ + (((x)>>24L)&0x000000ffL)) +#else +#ifndef AIX_REVERSE +#define AIX_REVERSE(x) (x) +#endif +#endif + +#ifdef MDR_REV +#define MDR_REVERSE(x) ((((x)<<24L)&0xff000000L) + \ + (((x)<< 8L)&0x00ff0000L) + \ + (((x)>> 8L)&0x0000ff00L) + \ + (((x)>>24L)&0x000000ffL)) +#else +#ifndef MDR_REVERSE +#define MDR_REVERSE(x) (x) +#endif +#endif + +#endif diff --git a/kernel/drivers/net/fddi/skfp/h/hwmtm.h b/kernel/drivers/net/fddi/skfp/h/hwmtm.h new file mode 100644 index 000000000..5924d4219 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/hwmtm.h @@ -0,0 +1,399 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _HWM_ +#define _HWM_ + +#include "mbuf.h" + +/* + * MACRO for DMA synchronization: + * The descriptor 'desc' is flushed for the device 'flag'. + * Devices are the CPU (DDI_DMA_SYNC_FORCPU) and the + * adapter (DDI_DMA_SYNC_FORDEV). + * + * 'desc' Pointer to a Rx or Tx descriptor. + * 'flag' Flag for direction (view for CPU or DEVICE) that + * should be synchronized. + * + * Empty macros and defines are specified here. The real macro + * is os-specific and should be defined in osdef1st.h. + */ +#ifndef DRV_BUF_FLUSH +#define DRV_BUF_FLUSH(desc,flag) +#define DDI_DMA_SYNC_FORCPU +#define DDI_DMA_SYNC_FORDEV +#endif + + /* + * hardware modul dependent receive modes + */ +#define RX_ENABLE_PASS_SMT 21 +#define RX_DISABLE_PASS_SMT 22 +#define RX_ENABLE_PASS_NSA 23 +#define RX_DISABLE_PASS_NSA 24 +#define RX_ENABLE_PASS_DB 25 +#define RX_DISABLE_PASS_DB 26 +#define RX_DISABLE_PASS_ALL 27 +#define RX_DISABLE_LLC_PROMISC 28 +#define RX_ENABLE_LLC_PROMISC 29 + + +#ifndef DMA_RD +#define DMA_RD 1 /* memory -> hw */ +#endif +#ifndef DMA_WR +#define DMA_WR 2 /* hw -> memory */ +#endif +#define SMT_BUF 0x80 + + /* + * bits of the frame status byte + */ +#define EN_IRQ_EOF 0x02 /* get IRQ after end of frame transmission */ +#define LOC_TX 0x04 /* send frame to the local SMT */ +#define LAST_FRAG 0x08 /* last TxD of the frame */ +#define FIRST_FRAG 0x10 /* first TxD of the frame */ +#define LAN_TX 0x20 /* send frame to network if set */ +#define RING_DOWN 0x40 /* error: unable to send, ring down */ +#define OUT_OF_TXD 0x80 /* error: not enough TxDs available */ + + +#ifndef NULL +#define NULL 0 +#endif + +#ifdef LITTLE_ENDIAN +#define HWM_REVERSE(x) (x) +#else +#define HWM_REVERSE(x) ((((x)<<24L)&0xff000000L) + \ + (((x)<< 8L)&0x00ff0000L) + \ + (((x)>> 8L)&0x0000ff00L) + \ + (((x)>>24L)&0x000000ffL)) +#endif + +#define C_INDIC (1L<<25) +#define A_INDIC (1L<<26) +#define RD_FS_LOCAL 0x80 + + /* + * DEBUG FLAGS + */ +#define DEBUG_SMTF 1 +#define DEBUG_SMT 2 +#define DEBUG_ECM 3 +#define DEBUG_RMT 4 +#define DEBUG_CFM 5 +#define DEBUG_PCM 6 +#define DEBUG_SBA 7 +#define DEBUG_ESS 8 + +#define DB_HWM_RX 10 +#define DB_HWM_TX 11 +#define DB_HWM_GEN 12 + +struct s_mbuf_pool { +#ifndef MB_OUTSIDE_SMC + SMbuf mb[MAX_MBUF] ; /* mbuf pool */ +#endif + SMbuf *mb_start ; /* points to the first mb */ + SMbuf *mb_free ; /* free queue */ +} ; + +struct hwm_r { + /* + * hardware modul specific receive variables + */ + u_int len ; /* length of the whole frame */ + char *mb_pos ; /* SMbuf receive position */ +} ; + +struct hw_modul { + /* + * All hardware modul specific variables + */ + struct s_mbuf_pool mbuf_pool ; + struct hwm_r r ; + + union s_fp_descr volatile *descr_p ; /* points to the desriptor area */ + + u_short pass_SMT ; /* pass SMT frames */ + u_short pass_NSA ; /* pass all NSA frames */ + u_short pass_DB ; /* pass Direct Beacon Frames */ + u_short pass_llc_promisc ; /* pass all llc frames (default ON) */ + + SMbuf *llc_rx_pipe ; /* points to the first queued llc fr */ + SMbuf *llc_rx_tail ; /* points to the last queued llc fr */ + int queued_rx_frames ; /* number of queued frames */ + + SMbuf *txd_tx_pipe ; /* points to first mb in the txd ring */ + SMbuf *txd_tx_tail ; /* points to last mb in the txd ring */ + int queued_txd_mb ; /* number of SMT MBufs in txd ring */ + + int rx_break ; /* rev. was breaked because ind. off */ + int leave_isr ; /* leave fddi_isr immedeately if set */ + int isr_flag ; /* set, when HWM is entered from isr */ + /* + * variables for the current transmit frame + */ + struct s_smt_tx_queue *tx_p ; /* pointer to the transmit queue */ + u_long tx_descr ; /* tx descriptor for FORMAC+ */ + int tx_len ; /* tx frame length */ + SMbuf *tx_mb ; /* SMT tx MBuf pointer */ + char *tx_data ; /* data pointer to the SMT tx Mbuf */ + + int detec_count ; /* counter for out of RxD condition */ + u_long rx_len_error ; /* rx len FORMAC != sum of fragments */ +} ; + + +/* + * DEBUG structs and macros + */ + +#ifdef DEBUG +struct os_debug { + int hwm_rx ; + int hwm_tx ; + int hwm_gen ; +} ; +#endif + +#ifdef DEBUG +#ifdef DEBUG_BRD +#define DB_P smc->debug +#else +#define DB_P debug +#endif + +#define DB_RX(a,b,c,lev) if (DB_P.d_os.hwm_rx >= (lev)) printf(a,b,c) +#define DB_TX(a,b,c,lev) if (DB_P.d_os.hwm_tx >= (lev)) printf(a,b,c) +#define DB_GEN(a,b,c,lev) if (DB_P.d_os.hwm_gen >= (lev)) printf(a,b,c) +#else /* DEBUG */ +#define DB_RX(a,b,c,lev) +#define DB_TX(a,b,c,lev) +#define DB_GEN(a,b,c,lev) +#endif /* DEBUG */ + +#ifndef SK_BREAK +#define SK_BREAK() +#endif + + +/* + * HWM Macros + */ + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_TX_PHYS) + * u_long HWM_GET_TX_PHYS(txd) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to read + * the physical address of the specified TxD. + * + * para txd pointer to the TxD + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_TX_PHYS(txd) (u_long)AIX_REVERSE((txd)->txd_tbadr) + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_TX_LEN) + * int HWM_GET_TX_LEN(txd) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to read + * the fragment length of the specified TxD + * + * para rxd pointer to the TxD + * + * return the length of the fragment in bytes + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_TX_LEN(txd) ((int)AIX_REVERSE((txd)->txd_tbctrl)& RD_LENGTH) + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_TX_USED) + * txd *HWM_GET_TX_USED(smc,queue) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to get the + * number of used TxDs for the queue, specified by the index. + * + * para queue the number of the send queue: Can be specified by + * QUEUE_A0, QUEUE_S or (frame_status & QUEUE_A0) + * + * return number of used TxDs for this send queue + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_TX_USED(smc,queue) (int) (smc)->hw.fp.tx_q[queue].tx_used + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_CURR_TXD) + * txd *HWM_GET_CURR_TXD(smc,queue) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to get the + * pointer to the TxD which points to the current queue put + * position. + * + * para queue the number of the send queue: Can be specified by + * QUEUE_A0, QUEUE_S or (frame_status & QUEUE_A0) + * + * return pointer to the current TxD + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_CURR_TXD(smc,queue) (struct s_smt_fp_txd volatile *)\ + (smc)->hw.fp.tx_q[queue].tx_curr_put + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_RX_FRAG_LEN) + * int HWM_GET_RX_FRAG_LEN(rxd) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to read + * the fragment length of the specified RxD + * + * para rxd pointer to the RxD + * + * return the length of the fragment in bytes + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_RX_FRAG_LEN(rxd) ((int)AIX_REVERSE((rxd)->rxd_rbctrl)& \ + RD_LENGTH) + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_RX_PHYS) + * u_long HWM_GET_RX_PHYS(rxd) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to read + * the physical address of the specified RxD. + * + * para rxd pointer to the RxD + * + * return the RxD's physical pointer to the data fragment + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_RX_PHYS(rxd) (u_long)AIX_REVERSE((rxd)->rxd_rbadr) + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_RX_USED) + * int HWM_GET_RX_USED(smc) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to get + * the count of used RXDs in receive queue 1. + * + * return the used RXD count of receive queue 1 + * + * NOTE: Remember, because of an ASIC bug at least one RXD should be unused + * in the descriptor ring ! + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_RX_USED(smc) ((int)(smc)->hw.fp.rx_q[QUEUE_R1].rx_used) + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_RX_FREE) + * int HWM_GET_RX_FREE(smc) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to get + * the rxd_free count of receive queue 1. + * + * return the rxd_free count of receive queue 1 + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_RX_FREE(smc) ((int)(smc)->hw.fp.rx_q[QUEUE_R1].rx_free-1) + +/* + * BEGIN_MANUAL_ENTRY(HWM_GET_CURR_RXD) + * rxd *HWM_GET_CURR_RXD(smc) + * + * function MACRO (hardware module, hwmtm.h) + * This macro may be invoked by the OS-specific module to get the + * pointer to the RxD which points to the current queue put + * position. + * + * return pointer to the current RxD + * + * END_MANUAL_ENTRY + */ +#define HWM_GET_CURR_RXD(smc) (struct s_smt_fp_rxd volatile *)\ + (smc)->hw.fp.rx_q[QUEUE_R1].rx_curr_put + +/* + * BEGIN_MANUAL_ENTRY(HWM_RX_CHECK) + * void HWM_RX_CHECK(smc,low_water) + * + * function MACRO (hardware module, hwmtm.h) + * This macro is invoked by the OS-specific before it left the + * function mac_drv_rx_complete. This macro calls mac_drv_fill_rxd + * if the number of used RxDs is equal or lower than the + * the given low water mark. + * + * para low_water low water mark of used RxD's + * + * END_MANUAL_ENTRY + */ +#ifndef HWM_NO_FLOW_CTL +#define HWM_RX_CHECK(smc,low_water) {\ + if ((low_water) >= (smc)->hw.fp.rx_q[QUEUE_R1].rx_used) {\ + mac_drv_fill_rxd(smc) ;\ + }\ +} +#else +#define HWM_RX_CHECK(smc,low_water) mac_drv_fill_rxd(smc) +#endif + +#ifndef HWM_EBASE +#define HWM_EBASE 500 +#endif + +#define HWM_E0001 HWM_EBASE + 1 +#define HWM_E0001_MSG "HWM: Wrong size of s_rxd_os struct" +#define HWM_E0002 HWM_EBASE + 2 +#define HWM_E0002_MSG "HWM: Wrong size of s_txd_os struct" +#define HWM_E0003 HWM_EBASE + 3 +#define HWM_E0003_MSG "HWM: smt_free_mbuf() called with NULL pointer" +#define HWM_E0004 HWM_EBASE + 4 +#define HWM_E0004_MSG "HWM: Parity error rx queue 1" +#define HWM_E0005 HWM_EBASE + 5 +#define HWM_E0005_MSG "HWM: Encoding error rx queue 1" +#define HWM_E0006 HWM_EBASE + 6 +#define HWM_E0006_MSG "HWM: Encoding error async tx queue" +#define HWM_E0007 HWM_EBASE + 7 +#define HWM_E0007_MSG "HWM: Encoding error sync tx queue" +#define HWM_E0008 HWM_EBASE + 8 +#define HWM_E0008_MSG "" +#define HWM_E0009 HWM_EBASE + 9 +#define HWM_E0009_MSG "HWM: Out of RxD condition detected" +#define HWM_E0010 HWM_EBASE + 10 +#define HWM_E0010_MSG "HWM: A protocol layer has tried to send a frame with an invalid frame control" +#define HWM_E0011 HWM_EBASE + 11 +#define HWM_E0011_MSG "HWM: mac_drv_clear_tx_queue was called although the hardware wasn't stopped" +#define HWM_E0012 HWM_EBASE + 12 +#define HWM_E0012_MSG "HWM: mac_drv_clear_rx_queue was called although the hardware wasn't stopped" +#define HWM_E0013 HWM_EBASE + 13 +#define HWM_E0013_MSG "HWM: mac_drv_repair_descr was called although the hardware wasn't stopped" + +#endif diff --git a/kernel/drivers/net/fddi/skfp/h/mbuf.h b/kernel/drivers/net/fddi/skfp/h/mbuf.h new file mode 100644 index 000000000..f2aadcda9 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/mbuf.h @@ -0,0 +1,50 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _MBUF_ +#define _MBUF_ + +#define M_SIZE 4504 + +#ifndef MAX_MBUF +#define MAX_MBUF 4 +#endif + +#ifndef NO_STD_MBUF +#define sm_next m_next +#define sm_off m_off +#define sm_len m_len +#define sm_data m_data +#define SMbuf Mbuf +#define mtod smtod +#define mtodoff smtodoff +#endif + +struct s_mbuf { + struct s_mbuf *sm_next ; /* low level linked list */ + short sm_off ; /* offset in m_data */ + u_int sm_len ; /* len of data */ +#ifdef PCI + int sm_use_count ; +#endif + char sm_data[M_SIZE] ; +} ; + +typedef struct s_mbuf SMbuf ; + +/* mbuf head, to typed data */ +#define smtod(x,t) ((t)((x)->sm_data + (x)->sm_off)) +#define smtodoff(x,t,o) ((t)((x)->sm_data + (o))) + +#endif /* _MBUF_ */ diff --git a/kernel/drivers/net/fddi/skfp/h/osdef1st.h b/kernel/drivers/net/fddi/skfp/h/osdef1st.h new file mode 100644 index 000000000..763ca18cb --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/osdef1st.h @@ -0,0 +1,125 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * Operating system-dependent definitions that have to be defined + * before any other header files are included. + */ + +// HWM (HardWare Module) Definitions +// ----------------------- + +#include <asm/byteorder.h> + +#ifdef __LITTLE_ENDIAN +#define LITTLE_ENDIAN +#else +#define BIG_ENDIAN +#endif + +// this is set in the makefile +// #define PCI /* only PCI adapters supported by this driver */ +// #define MEM_MAPPED_IO /* use memory mapped I/O */ + + +#define USE_CAN_ADDR /* DA and SA in MAC header are canonical. */ + +#define MB_OUTSIDE_SMC /* SMT Mbufs outside of smc struct. */ + +// ----------------------- + + +// SMT Definitions +// ----------------------- +#define SYNC /* allow synchronous frames */ + +// #define SBA /* Synchronous Bandwidth Allocator support */ + /* not available as free source */ + +#define ESS /* SBA End Station Support */ + +#define SMT_PANIC(smc, nr, msg) printk(KERN_INFO "SMT PANIC: code: %d, msg: %s\n",nr,msg) + + +#ifdef DEBUG +#define printf(s,args...) printk(KERN_INFO s, ## args) +#endif + +// #define HW_PTR u_long +// ----------------------- + + + +// HWM and OS-specific buffer definitions +// ----------------------- + +// default number of receive buffers. +#define NUM_RECEIVE_BUFFERS 10 + +// default number of transmit buffers. +#define NUM_TRANSMIT_BUFFERS 10 + +// Number of SMT buffers (Mbufs). +#define NUM_SMT_BUF 4 + +// Number of TXDs for asynchronous transmit queue. +#define HWM_ASYNC_TXD_COUNT (NUM_TRANSMIT_BUFFERS + NUM_SMT_BUF) + +// Number of TXDs for synchronous transmit queue. +#define HWM_SYNC_TXD_COUNT HWM_ASYNC_TXD_COUNT + + +// Number of RXDs for receive queue #1. +// Note: Workaround for ASIC Errata #7: One extra RXD is required. +#if (NUM_RECEIVE_BUFFERS > 100) +#define SMT_R1_RXD_COUNT (1 + 100) +#else +#define SMT_R1_RXD_COUNT (1 + NUM_RECEIVE_BUFFERS) +#endif + +// Number of RXDs for receive queue #2. +#define SMT_R2_RXD_COUNT 0 // Not used. +// ----------------------- + + + +/* + * OS-specific part of the transmit/receive descriptor structure (TXD/RXD). + * + * Note: The size of these structures must follow this rule: + * + * sizeof(struct) + 2*sizeof(void*) == n * 16, n >= 1 + * + * We use the dma_addr fields under Linux to keep track of the + * DMA address of the packet data, for later pci_unmap_single. -DaveM + */ + +struct s_txd_os { // os-specific part of transmit descriptor + struct sk_buff *skb; + dma_addr_t dma_addr; +} ; + +struct s_rxd_os { // os-specific part of receive descriptor + struct sk_buff *skb; + dma_addr_t dma_addr; +} ; + + +/* + * So we do not need to make too many modifications to the generic driver + * parts, we take advantage of the AIX byte swapping macro interface. + */ + +#define AIX_REVERSE(x) ((u32)le32_to_cpu((u32)(x))) +#define MDR_REVERSE(x) ((u32)le32_to_cpu((u32)(x))) diff --git a/kernel/drivers/net/fddi/skfp/h/sba.h b/kernel/drivers/net/fddi/skfp/h/sba.h new file mode 100644 index 000000000..35ddb44a1 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/sba.h @@ -0,0 +1,142 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * Synchronous Bandwidth Allocation (SBA) structs + */ + +#ifndef _SBA_ +#define _SBA_ + +#include "mbuf.h" +#include "sba_def.h" + +#ifdef SBA + +/* Timer Cell Template */ +struct timer_cell { + struct timer_cell *next_ptr ; + struct timer_cell *prev_ptr ; + u_long start_time ; + struct s_sba_node_vars *node_var ; +} ; + +/* + * Node variables + */ +struct s_sba_node_vars { + u_char change_resp_flag ; + u_char report_resp_flag ; + u_char change_req_flag ; + u_char report_req_flag ; + long change_amount ; + long node_overhead ; + long node_payload ; + u_long node_status ; + u_char deallocate_status ; + u_char timer_state ; + u_short report_cnt ; + long lastrep_req_tranid ; + struct fddi_addr mac_address ; + struct s_sba_sessions *node_sessions ; + struct timer_cell timer ; +} ; + +/* + * Session variables + */ +struct s_sba_sessions { + u_long deallocate_status ; + long session_overhead ; + u_long min_segment_size ; + long session_payload ; + u_long session_status ; + u_long sba_category ; + long lastchg_req_tranid ; + u_short session_id ; + u_char class ; + u_char fddi2 ; + u_long max_t_neg ; + struct s_sba_sessions *next_session ; +} ; + +struct s_sba { + + struct s_sba_node_vars node[MAX_NODES] ; + struct s_sba_sessions session[MAX_SESSIONS] ; + + struct s_sba_sessions *free_session ; /* points to the first */ + /* free session */ + + struct timer_cell *tail_timer ; /* points to the last timer cell */ + + /* + * variables for allocation actions + */ + long total_payload ; /* Total Payload */ + long total_overhead ; /* Total Overhead */ + long sba_allocatable ; /* allocatable sync bandwidth */ + + /* + * RAF message receive parameters + */ + long msg_path_index ; /* Path Type */ + long msg_sba_pl_req ; /* Payload Request */ + long msg_sba_ov_req ; /* Overhead Request */ + long msg_mib_pl ; /* Current Payload for this Path */ + long msg_mib_ov ; /* Current Overhead for this Path*/ + long msg_category ; /* Category of the Allocation */ + u_long msg_max_t_neg ; /* longest T_Neg acceptable */ + u_long msg_min_seg_siz ; /* minimum segement size */ + struct smt_header *sm ; /* points to the rec message */ + struct fddi_addr *msg_alloc_addr ; /* Allocation Address */ + + /* + * SBA variables + */ + u_long sba_t_neg ; /* holds the last T_NEG */ + long sba_max_alloc ; /* the parsed value of SBAAvailable */ + + /* + * SBA state machine variables + */ + short sba_next_state ; /* the next state of the SBA */ + char sba_command ; /* holds the execuded SBA cmd */ + u_char sba_available ; /* parsed value after possible check */ +} ; + +#endif /* SBA */ + + /* + * variables for the End Station Support + */ +struct s_ess { + + /* + * flags and counters + */ + u_char sync_bw_available ; /* is set if sync bw is allocated */ + u_char local_sba_active ; /* set when a local sba is available */ + char raf_act_timer_poll ; /* activate the timer to send allc req */ + char timer_count ; /* counts every timer function call */ + + SMbuf *sba_reply_pend ; /* local reply for the sba is pending */ + + /* + * variables for the ess bandwidth control + */ + long sync_bw ; /* holds the allocaed sync bw */ + u_long alloc_trans_id ; /* trans id of the last alloc req */ +} ; +#endif diff --git a/kernel/drivers/net/fddi/skfp/h/sba_def.h b/kernel/drivers/net/fddi/skfp/h/sba_def.h new file mode 100644 index 000000000..0459a095d --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/sba_def.h @@ -0,0 +1,76 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#define PHYS 0 /* physical addr */ +#define PERM_ADDR 0x80 /* permanet address */ +#define SB_STATIC 0x00000001 +#define MAX_PAYLOAD 1562 +#define PRIMARY_RING 0x00000001 +#ifndef NULL +#define NULL 0x00 +#endif + +/*********************** SB_Input Variable Values ***********************/ +/* may be needed when ever the SBA state machine is called */ + +#define UNKNOWN_SYNC_SOURCE 0x0001 +#define REQ_ALLOCATION 0x0002 +#define REPORT_RESP 0x0003 +#define CHANGE_RESP 0x0004 +#define TNEG 0x0005 +#define NIF 0x0006 +#define SB_STOP 0x0007 +#define SB_START 0x0008 +#define REPORT_TIMER 0x0009 +#define CHANGE_REQUIRED 0x000A + +#define DEFAULT_OV 50 + +#ifdef SBA +/**************************** SBA STATES *****************************/ + +#define SBA_STANDBY 0x00000000 +#define SBA_ACTIVE 0x00000001 +#define SBA_RECOVERY 0x00000002 +#define SBA_REPORT 0x00000003 +#define SBA_CHANGE 0x00000004 + +/**************************** OTHERS *********************************/ + +#define FIFTY_PERCENT 50 /* bytes per second */ +#define MAX_SESSIONS 150 +#define TWO_MINUTES 13079 /* 9.175 ms/tick */ +#define FIFTY_BYTES 50 +#define SBA_DENIED 0x0000000D +#define I_NEED_ONE 0x00000000 +#define MAX_NODES 50 +/*#define T_REPORT 0x59682F00L*/ /* 120s/80ns in Hex */ +#define TWO_MIN 120 /* seconds */ +#define SBA_ST_UNKNOWN 0x00000002 +#define SBA_ST_ACTIVE 0x00000001 +#define S_CLEAR 0x00000000L +#define ZERO 0x00000000 +#define FULL 0x00000000 /* old: 0xFFFFFFFFF */ +#define S_SET 0x00000001L +#define LOW_PRIO 0x02 /* ??????? */ +#define OK 0x01 /* ??????? */ +#define NOT_OK 0x00 /* ??????? */ + +/****************************************/ +/* deallocate_status[ni][si] values */ +/****************************************/ +#define TX_CHANGE 0X00000001L +#define PENDING 0x00000002L +#define NONE 0X00000000L +#endif diff --git a/kernel/drivers/net/fddi/skfp/h/skfbi.h b/kernel/drivers/net/fddi/skfp/h/skfbi.h new file mode 100644 index 000000000..3de2f0d15 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/skfbi.h @@ -0,0 +1,1128 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _SKFBI_H_ +#define _SKFBI_H_ + +/* + * FDDI-Fx (x := {I(SA), P(CI)}) + * address calculation & function defines + */ + +/*--------------------------------------------------------------------------*/ +#ifdef PCI + +/* + * (DV) = only defined for Da Vinci + * (ML) = only defined for Monalisa + */ + +/* + * Configuration Space header + */ +#define PCI_VENDOR_ID 0x00 /* 16 bit Vendor ID */ +#define PCI_DEVICE_ID 0x02 /* 16 bit Device ID */ +#define PCI_COMMAND 0x04 /* 16 bit Command */ +#define PCI_STATUS 0x06 /* 16 bit Status */ +#define PCI_REV_ID 0x08 /* 8 bit Revision ID */ +#define PCI_CLASS_CODE 0x09 /* 24 bit Class Code */ +#define PCI_CACHE_LSZ 0x0c /* 8 bit Cache Line Size */ +#define PCI_LAT_TIM 0x0d /* 8 bit Latency Timer */ +#define PCI_HEADER_T 0x0e /* 8 bit Header Type */ +#define PCI_BIST 0x0f /* 8 bit Built-in selftest */ +#define PCI_BASE_1ST 0x10 /* 32 bit 1st Base address */ +#define PCI_BASE_2ND 0x14 /* 32 bit 2nd Base address */ +/* Byte 18..2b: Reserved */ +#define PCI_SUB_VID 0x2c /* 16 bit Subsystem Vendor ID */ +#define PCI_SUB_ID 0x2e /* 16 bit Subsystem ID */ +#define PCI_BASE_ROM 0x30 /* 32 bit Expansion ROM Base Address */ +/* Byte 34..33: Reserved */ +#define PCI_CAP_PTR 0x34 /* 8 bit (ML) Capabilities Ptr */ +/* Byte 35..3b: Reserved */ +#define PCI_IRQ_LINE 0x3c /* 8 bit Interrupt Line */ +#define PCI_IRQ_PIN 0x3d /* 8 bit Interrupt Pin */ +#define PCI_MIN_GNT 0x3e /* 8 bit Min_Gnt */ +#define PCI_MAX_LAT 0x3f /* 8 bit Max_Lat */ +/* Device Dependent Region */ +#define PCI_OUR_REG 0x40 /* 32 bit (DV) Our Register */ +#define PCI_OUR_REG_1 0x40 /* 32 bit (ML) Our Register 1 */ +#define PCI_OUR_REG_2 0x44 /* 32 bit (ML) Our Register 2 */ +/* Power Management Region */ +#define PCI_PM_CAP_ID 0x48 /* 8 bit (ML) Power Management Cap. ID */ +#define PCI_PM_NITEM 0x49 /* 8 bit (ML) Next Item Ptr */ +#define PCI_PM_CAP_REG 0x4a /* 16 bit (ML) Power Management Capabilities */ +#define PCI_PM_CTL_STS 0x4c /* 16 bit (ML) Power Manag. Control/Status */ +/* Byte 0x4e: Reserved */ +#define PCI_PM_DAT_REG 0x4f /* 8 bit (ML) Power Manag. Data Register */ +/* VPD Region */ +#define PCI_VPD_CAP_ID 0x50 /* 8 bit (ML) VPD Cap. ID */ +#define PCI_VPD_NITEM 0x51 /* 8 bit (ML) Next Item Ptr */ +#define PCI_VPD_ADR_REG 0x52 /* 16 bit (ML) VPD Address Register */ +#define PCI_VPD_DAT_REG 0x54 /* 32 bit (ML) VPD Data Register */ +/* Byte 58..ff: Reserved */ + +/* + * I2C Address (PCI Config) + * + * Note: The temperature and voltage sensors are relocated on a different + * I2C bus. + */ +#define I2C_ADDR_VPD 0xA0 /* I2C address for the VPD EEPROM */ + +/* + * Define Bits and Values of the registers + */ +/* PCI_VENDOR_ID 16 bit Vendor ID */ +/* PCI_DEVICE_ID 16 bit Device ID */ +/* Values for Vendor ID and Device ID shall be patched into the code */ +/* PCI_COMMAND 16 bit Command */ +#define PCI_FBTEN 0x0200 /* Bit 9: Fast Back-To-Back enable */ +#define PCI_SERREN 0x0100 /* Bit 8: SERR enable */ +#define PCI_ADSTEP 0x0080 /* Bit 7: Address Stepping */ +#define PCI_PERREN 0x0040 /* Bit 6: Parity Report Response enable */ +#define PCI_VGA_SNOOP 0x0020 /* Bit 5: VGA palette snoop */ +#define PCI_MWIEN 0x0010 /* Bit 4: Memory write an inv cycl ena */ +#define PCI_SCYCEN 0x0008 /* Bit 3: Special Cycle enable */ +#define PCI_BMEN 0x0004 /* Bit 2: Bus Master enable */ +#define PCI_MEMEN 0x0002 /* Bit 1: Memory Space Access enable */ +#define PCI_IOEN 0x0001 /* Bit 0: IO Space Access enable */ + +/* PCI_STATUS 16 bit Status */ +#define PCI_PERR 0x8000 /* Bit 15: Parity Error */ +#define PCI_SERR 0x4000 /* Bit 14: Signaled SERR */ +#define PCI_RMABORT 0x2000 /* Bit 13: Received Master Abort */ +#define PCI_RTABORT 0x1000 /* Bit 12: Received Target Abort */ +#define PCI_STABORT 0x0800 /* Bit 11: Sent Target Abort */ +#define PCI_DEVSEL 0x0600 /* Bit 10..9: DEVSEL Timing */ +#define PCI_DEV_FAST (0<<9) /* fast */ +#define PCI_DEV_MEDIUM (1<<9) /* medium */ +#define PCI_DEV_SLOW (2<<9) /* slow */ +#define PCI_DATAPERR 0x0100 /* Bit 8: DATA Parity error detected */ +#define PCI_FB2BCAP 0x0080 /* Bit 7: Fast Back-to-Back Capability */ +#define PCI_UDF 0x0040 /* Bit 6: User Defined Features */ +#define PCI_66MHZCAP 0x0020 /* Bit 5: 66 MHz PCI bus clock capable */ +#define PCI_NEWCAP 0x0010 /* Bit 4: New cap. list implemented */ + +#define PCI_ERRBITS (PCI_PERR|PCI_SERR|PCI_RMABORT|PCI_STABORT|PCI_DATAPERR) + +/* PCI_REV_ID 8 bit Revision ID */ +/* PCI_CLASS_CODE 24 bit Class Code */ +/* Byte 2: Base Class (02) */ +/* Byte 1: SubClass (02) */ +/* Byte 0: Programming Interface (00) */ + +/* PCI_CACHE_LSZ 8 bit Cache Line Size */ +/* Possible values: 0,2,4,8,16 */ + +/* PCI_LAT_TIM 8 bit Latency Timer */ + +/* PCI_HEADER_T 8 bit Header Type */ +#define PCI_HD_MF_DEV 0x80 /* Bit 7: 0= single, 1= multi-func dev */ +#define PCI_HD_TYPE 0x7f /* Bit 6..0: Header Layout 0= normal */ + +/* PCI_BIST 8 bit Built-in selftest */ +#define PCI_BIST_CAP 0x80 /* Bit 7: BIST Capable */ +#define PCI_BIST_ST 0x40 /* Bit 6: Start BIST */ +#define PCI_BIST_RET 0x0f /* Bit 3..0: Completion Code */ + +/* PCI_BASE_1ST 32 bit 1st Base address */ +#define PCI_MEMSIZE 0x800L /* use 2 kB Memory Base */ +#define PCI_MEMBASE_BITS 0xfffff800L /* Bit 31..11: Memory Base Address */ +#define PCI_MEMSIZE_BIIS 0x000007f0L /* Bit 10..4: Memory Size Req. */ +#define PCI_PREFEN 0x00000008L /* Bit 3: Prefetchable */ +#define PCI_MEM_TYP 0x00000006L /* Bit 2..1: Memory Type */ +#define PCI_MEM32BIT (0<<1) /* Base addr anywhere in 32 Bit range */ +#define PCI_MEM1M (1<<1) /* Base addr below 1 MegaByte */ +#define PCI_MEM64BIT (2<<1) /* Base addr anywhere in 64 Bit range */ +#define PCI_MEMSPACE 0x00000001L /* Bit 0: Memory Space Indic. */ + +/* PCI_SUB_VID 16 bit Subsystem Vendor ID */ +/* PCI_SUB_ID 16 bit Subsystem ID */ + +/* PCI_BASE_ROM 32 bit Expansion ROM Base Address */ +#define PCI_ROMBASE 0xfffe0000L /* Bit 31..17: ROM BASE address (1st) */ +#define PCI_ROMBASZ 0x0001c000L /* Bit 16..14: Treat as BASE or SIZE */ +#define PCI_ROMSIZE 0x00003800L /* Bit 13..11: ROM Size Requirements */ +#define PCI_ROMEN 0x00000001L /* Bit 0: Address Decode enable */ + +/* PCI_CAP_PTR 8 bit New Capabilities Pointers */ +/* PCI_IRQ_LINE 8 bit Interrupt Line */ +/* PCI_IRQ_PIN 8 bit Interrupt Pin */ +/* PCI_MIN_GNT 8 bit Min_Gnt */ +/* PCI_MAX_LAT 8 bit Max_Lat */ +/* Device Dependent Region */ +/* PCI_OUR_REG (DV) 32 bit Our Register */ +/* PCI_OUR_REG_1 (ML) 32 bit Our Register 1 */ + /* Bit 31..29: reserved */ +#define PCI_PATCH_DIR (3L<<27) /*(DV) Bit 28..27: Ext Patchs direction */ +#define PCI_PATCH_DIR_0 (1L<<27) /*(DV) Type of the pins EXT_PATCHS<1..0> */ +#define PCI_PATCH_DIR_1 (1L<<28) /* 0 = input */ + /* 1 = output */ +#define PCI_EXT_PATCHS (3L<<25) /*(DV) Bit 26..25: Extended Patches */ +#define PCI_EXT_PATCH_0 (1L<<25) /*(DV) */ +#define PCI_EXT_PATCH_1 (1L<<26) /* CLK for MicroWire (ML) */ +#define PCI_VIO (1L<<25) /*(ML) */ +#define PCI_EN_BOOT (1L<<24) /* Bit 24: Enable BOOT via ROM */ + /* 1 = Don't boot with ROM */ + /* 0 = Boot with ROM */ +#define PCI_EN_IO (1L<<23) /* Bit 23: Mapping to IO space */ +#define PCI_EN_FPROM (1L<<22) /* Bit 22: FLASH mapped to mem? */ + /* 1 = Map Flash to Memory */ + /* 0 = Disable all addr. decoding */ +#define PCI_PAGESIZE (3L<<20) /* Bit 21..20: FLASH Page Size */ +#define PCI_PAGE_16 (0L<<20) /* 16 k pages */ +#define PCI_PAGE_32K (1L<<20) /* 32 k pages */ +#define PCI_PAGE_64K (2L<<20) /* 64 k pages */ +#define PCI_PAGE_128K (3L<<20) /* 128 k pages */ + /* Bit 19: reserved (ML) and (DV) */ +#define PCI_PAGEREG (7L<<16) /* Bit 18..16: Page Register */ + /* Bit 15: reserved */ +#define PCI_FORCE_BE (1L<<14) /* Bit 14: Assert all BEs on MR */ +#define PCI_DIS_MRL (1L<<13) /* Bit 13: Disable Mem R Line */ +#define PCI_DIS_MRM (1L<<12) /* Bit 12: Disable Mem R multip */ +#define PCI_DIS_MWI (1L<<11) /* Bit 11: Disable Mem W & inv */ +#define PCI_DISC_CLS (1L<<10) /* Bit 10: Disc: cacheLsz bound */ +#define PCI_BURST_DIS (1L<<9) /* Bit 9: Burst Disable */ +#define PCI_BYTE_SWAP (1L<<8) /*(DV) Bit 8: Byte Swap in DATA */ +#define PCI_SKEW_DAS (0xfL<<4) /* Bit 7..4: Skew Ctrl, DAS Ext */ +#define PCI_SKEW_BASE (0xfL<<0) /* Bit 3..0: Skew Ctrl, Base */ + +/* PCI_OUR_REG_2 (ML) 32 bit Our Register 2 (Monalisa only) */ +#define PCI_VPD_WR_TH (0xffL<<24) /* Bit 24..31 VPD Write Threshold */ +#define PCI_DEV_SEL (0x7fL<<17) /* Bit 17..23 EEPROM Device Select */ +#define PCI_VPD_ROM_SZ (7L<<14) /* Bit 14..16 VPD ROM Size */ + /* Bit 12..13 reserved */ +#define PCI_PATCH_DIR2 (0xfL<<8) /* Bit 8..11 Ext Patchs dir 2..5 */ +#define PCI_PATCH_DIR_2 (1L<<8) /* Bit 8 CS for MicroWire */ +#define PCI_PATCH_DIR_3 (1L<<9) +#define PCI_PATCH_DIR_4 (1L<<10) +#define PCI_PATCH_DIR_5 (1L<<11) +#define PCI_EXT_PATCHS2 (0xfL<<4) /* Bit 4..7 Extended Patches */ +#define PCI_EXT_PATCH_2 (1L<<4) /* Bit 4 CS for MicroWire */ +#define PCI_EXT_PATCH_3 (1L<<5) +#define PCI_EXT_PATCH_4 (1L<<6) +#define PCI_EXT_PATCH_5 (1L<<7) +#define PCI_EN_DUMMY_RD (1L<<3) /* Bit 3 Enable Dummy Read */ +#define PCI_REV_DESC (1L<<2) /* Bit 2 Reverse Desc. Bytes */ +#define PCI_USEADDR64 (1L<<1) /* Bit 1 Use 64 Bit Addresse */ +#define PCI_USEDATA64 (1L<<0) /* Bit 0 Use 64 Bit Data bus ext*/ + +/* Power Management Region */ +/* PCI_PM_CAP_ID 8 bit (ML) Power Management Cap. ID */ +/* PCI_PM_NITEM 8 bit (ML) Next Item Ptr */ +/* PCI_PM_CAP_REG 16 bit (ML) Power Management Capabilities*/ +#define PCI_PME_SUP (0x1f<<11) /* Bit 11..15 PM Manag. Event Support*/ +#define PCI_PM_D2_SUB (1<<10) /* Bit 10 D2 Support Bit */ +#define PCI_PM_D1_SUB (1<<9) /* Bit 9 D1 Support Bit */ + /* Bit 6..8 reserved */ +#define PCI_PM_DSI (1<<5) /* Bit 5 Device Specific Init.*/ +#define PCI_PM_APS (1<<4) /* Bit 4 Auxialiary Power Src */ +#define PCI_PME_CLOCK (1<<3) /* Bit 3 PM Event Clock */ +#define PCI_PM_VER (7<<0) /* Bit 0..2 PM PCI Spec. version */ + +/* PCI_PM_CTL_STS 16 bit (ML) Power Manag. Control/Status */ +#define PCI_PME_STATUS (1<<15) /* Bit 15 PFA doesn't sup. PME#*/ +#define PCI_PM_DAT_SCL (3<<13) /* Bit 13..14 dat reg Scaling factor */ +#define PCI_PM_DAT_SEL (0xf<<9) /* Bit 9..12 PM data selector field */ + /* Bit 7.. 2 reserved */ +#define PCI_PM_STATE (3<<0) /* Bit 0.. 1 Power Management State */ +#define PCI_PM_STATE_D0 (0<<0) /* D0: Operational (default) */ +#define PCI_PM_STATE_D1 (1<<0) /* D1: not supported */ +#define PCI_PM_STATE_D2 (2<<0) /* D2: not supported */ +#define PCI_PM_STATE_D3 (3<<0) /* D3: HOT, Power Down and Reset */ + +/* PCI_PM_DAT_REG 8 bit (ML) Power Manag. Data Register */ +/* VPD Region */ +/* PCI_VPD_CAP_ID 8 bit (ML) VPD Cap. ID */ +/* PCI_VPD_NITEM 8 bit (ML) Next Item Ptr */ +/* PCI_VPD_ADR_REG 16 bit (ML) VPD Address Register */ +#define PCI_VPD_FLAG (1<<15) /* Bit 15 starts VPD rd/wd cycle*/ + +/* PCI_VPD_DAT_REG 32 bit (ML) VPD Data Register */ + +/* + * Control Register File: + * Bank 0 + */ +#define B0_RAP 0x0000 /* 8 bit register address port */ + /* 0x0001 - 0x0003: reserved */ +#define B0_CTRL 0x0004 /* 8 bit control register */ +#define B0_DAS 0x0005 /* 8 Bit control register (DAS) */ +#define B0_LED 0x0006 /* 8 Bit LED register */ +#define B0_TST_CTRL 0x0007 /* 8 bit test control register */ +#define B0_ISRC 0x0008 /* 32 bit Interrupt source register */ +#define B0_IMSK 0x000c /* 32 bit Interrupt mask register */ + +/* 0x0010 - 0x006b: formac+ (supernet_3) fequently used registers */ +#define B0_CMDREG1 0x0010 /* write command reg 1 instruction */ +#define B0_CMDREG2 0x0014 /* write command reg 2 instruction */ +#define B0_ST1U 0x0010 /* read upper 16-bit of status reg 1 */ +#define B0_ST1L 0x0014 /* read lower 16-bit of status reg 1 */ +#define B0_ST2U 0x0018 /* read upper 16-bit of status reg 2 */ +#define B0_ST2L 0x001c /* read lower 16-bit of status reg 2 */ + +#define B0_MARR 0x0020 /* r/w the memory read addr register */ +#define B0_MARW 0x0024 /* r/w the memory write addr register*/ +#define B0_MDRU 0x0028 /* r/w upper 16-bit of mem. data reg */ +#define B0_MDRL 0x002c /* r/w lower 16-bit of mem. data reg */ + +#define B0_MDREG3 0x0030 /* r/w Mode Register 3 */ +#define B0_ST3U 0x0034 /* read upper 16-bit of status reg 3 */ +#define B0_ST3L 0x0038 /* read lower 16-bit of status reg 3 */ +#define B0_IMSK3U 0x003c /* r/w upper 16-bit of IMSK reg 3 */ +#define B0_IMSK3L 0x0040 /* r/w lower 16-bit of IMSK reg 3 */ +#define B0_IVR 0x0044 /* read Interrupt Vector register */ +#define B0_IMR 0x0048 /* r/w Interrupt mask register */ +/* 0x4c Hidden */ + +#define B0_CNTRL_A 0x0050 /* control register A (r/w) */ +#define B0_CNTRL_B 0x0054 /* control register B (r/w) */ +#define B0_INTR_MASK 0x0058 /* interrupt mask (r/w) */ +#define B0_XMIT_VECTOR 0x005c /* transmit vector register (r/w) */ + +#define B0_STATUS_A 0x0060 /* status register A (read only) */ +#define B0_STATUS_B 0x0064 /* status register B (read only) */ +#define B0_CNTRL_C 0x0068 /* control register C (r/w) */ +#define B0_MDREG1 0x006c /* r/w Mode Register 1 */ + +#define B0_R1_CSR 0x0070 /* 32 bit BMU control/status reg (rec q 1) */ +#define B0_R2_CSR 0x0074 /* 32 bit BMU control/status reg (rec q 2)(DV)*/ +#define B0_XA_CSR 0x0078 /* 32 bit BMU control/status reg (a xmit q) */ +#define B0_XS_CSR 0x007c /* 32 bit BMU control/status reg (s xmit q) */ + +/* + * Bank 1 + * - completely empty (this is the RAP Block window) + * Note: if RAP = 1 this page is reserved + */ + +/* + * Bank 2 + */ +#define B2_MAC_0 0x0100 /* 8 bit MAC address Byte 0 */ +#define B2_MAC_1 0x0101 /* 8 bit MAC address Byte 1 */ +#define B2_MAC_2 0x0102 /* 8 bit MAC address Byte 2 */ +#define B2_MAC_3 0x0103 /* 8 bit MAC address Byte 3 */ +#define B2_MAC_4 0x0104 /* 8 bit MAC address Byte 4 */ +#define B2_MAC_5 0x0105 /* 8 bit MAC address Byte 5 */ +#define B2_MAC_6 0x0106 /* 8 bit MAC address Byte 6 (== 0) (DV) */ +#define B2_MAC_7 0x0107 /* 8 bit MAC address Byte 7 (== 0) (DV) */ + +#define B2_CONN_TYP 0x0108 /* 8 bit Connector type */ +#define B2_PMD_TYP 0x0109 /* 8 bit PMD type */ + /* 0x010a - 0x010b: reserved */ + /* Eprom registers are currently of no use */ +#define B2_E_0 0x010c /* 8 bit EPROM Byte 0 */ +#define B2_E_1 0x010d /* 8 bit EPROM Byte 1 */ +#define B2_E_2 0x010e /* 8 bit EPROM Byte 2 */ +#define B2_E_3 0x010f /* 8 bit EPROM Byte 3 */ +#define B2_FAR 0x0110 /* 32 bit Flash-Prom Address Register/Counter */ +#define B2_FDP 0x0114 /* 8 bit Flash-Prom Data Port */ + /* 0x0115 - 0x0117: reserved */ +#define B2_LD_CRTL 0x0118 /* 8 bit loader control */ +#define B2_LD_TEST 0x0119 /* 8 bit loader test */ + /* 0x011a - 0x011f: reserved */ +#define B2_TI_INI 0x0120 /* 32 bit Timer init value */ +#define B2_TI_VAL 0x0124 /* 32 bit Timer value */ +#define B2_TI_CRTL 0x0128 /* 8 bit Timer control */ +#define B2_TI_TEST 0x0129 /* 8 Bit Timer Test */ + /* 0x012a - 0x012f: reserved */ +#define B2_WDOG_INI 0x0130 /* 32 bit Watchdog init value */ +#define B2_WDOG_VAL 0x0134 /* 32 bit Watchdog value */ +#define B2_WDOG_CRTL 0x0138 /* 8 bit Watchdog control */ +#define B2_WDOG_TEST 0x0139 /* 8 Bit Watchdog Test */ + /* 0x013a - 0x013f: reserved */ +#define B2_RTM_INI 0x0140 /* 32 bit RTM init value */ +#define B2_RTM_VAL 0x0144 /* 32 bit RTM value */ +#define B2_RTM_CRTL 0x0148 /* 8 bit RTM control */ +#define B2_RTM_TEST 0x0149 /* 8 Bit RTM Test */ + +#define B2_TOK_COUNT 0x014c /* (ML) 32 bit Token Counter */ +#define B2_DESC_ADDR_H 0x0150 /* (ML) 32 bit Desciptor Base Addr Reg High */ +#define B2_CTRL_2 0x0154 /* (ML) 8 bit Control Register 2 */ +#define B2_IFACE_REG 0x0155 /* (ML) 8 bit Interface Register */ + /* 0x0156: reserved */ +#define B2_TST_CTRL_2 0x0157 /* (ML) 8 bit Test Control Register 2 */ +#define B2_I2C_CTRL 0x0158 /* (ML) 32 bit I2C Control Register */ +#define B2_I2C_DATA 0x015c /* (ML) 32 bit I2C Data Register */ + +#define B2_IRQ_MOD_INI 0x0160 /* (ML) 32 bit IRQ Moderation Timer Init Reg. */ +#define B2_IRQ_MOD_VAL 0x0164 /* (ML) 32 bit IRQ Moderation Timer Value */ +#define B2_IRQ_MOD_CTRL 0x0168 /* (ML) 8 bit IRQ Moderation Timer Control */ +#define B2_IRQ_MOD_TEST 0x0169 /* (ML) 8 bit IRQ Moderation Timer Test */ + /* 0x016a - 0x017f: reserved */ + +/* + * Bank 3 + */ +/* + * This is a copy of the Configuration register file (lower half) + */ +#define B3_CFG_SPC 0x180 + +/* + * Bank 4 + */ +#define B4_R1_D 0x0200 /* 4*32 bit current receive Descriptor */ +#define B4_R1_DA 0x0210 /* 32 bit current rec desc address */ +#define B4_R1_AC 0x0214 /* 32 bit current receive Address Count */ +#define B4_R1_BC 0x0218 /* 32 bit current receive Byte Counter */ +#define B4_R1_CSR 0x021c /* 32 bit BMU Control/Status Register */ +#define B4_R1_F 0x0220 /* 32 bit flag register */ +#define B4_R1_T1 0x0224 /* 32 bit Test Register 1 */ +#define B4_R1_T1_TR 0x0224 /* 8 bit Test Register 1 TR */ +#define B4_R1_T1_WR 0x0225 /* 8 bit Test Register 1 WR */ +#define B4_R1_T1_RD 0x0226 /* 8 bit Test Register 1 RD */ +#define B4_R1_T1_SV 0x0227 /* 8 bit Test Register 1 SV */ +#define B4_R1_T2 0x0228 /* 32 bit Test Register 2 */ +#define B4_R1_T3 0x022c /* 32 bit Test Register 3 */ +#define B4_R1_DA_H 0x0230 /* (ML) 32 bit Curr Rx Desc Address High */ +#define B4_R1_AC_H 0x0234 /* (ML) 32 bit Curr Addr Counter High dword */ + /* 0x0238 - 0x023f: reserved */ + /* Receive queue 2 is removed on Monalisa */ +#define B4_R2_D 0x0240 /* 4*32 bit current receive Descriptor (q2) */ +#define B4_R2_DA 0x0250 /* 32 bit current rec desc address (q2) */ +#define B4_R2_AC 0x0254 /* 32 bit current receive Address Count (q2) */ +#define B4_R2_BC 0x0258 /* 32 bit current receive Byte Counter (q2) */ +#define B4_R2_CSR 0x025c /* 32 bit BMU Control/Status Register (q2) */ +#define B4_R2_F 0x0260 /* 32 bit flag register (q2) */ +#define B4_R2_T1 0x0264 /* 32 bit Test Register 1 (q2) */ +#define B4_R2_T1_TR 0x0264 /* 8 bit Test Register 1 TR (q2) */ +#define B4_R2_T1_WR 0x0265 /* 8 bit Test Register 1 WR (q2) */ +#define B4_R2_T1_RD 0x0266 /* 8 bit Test Register 1 RD (q2) */ +#define B4_R2_T1_SV 0x0267 /* 8 bit Test Register 1 SV (q2) */ +#define B4_R2_T2 0x0268 /* 32 bit Test Register 2 (q2) */ +#define B4_R2_T3 0x026c /* 32 bit Test Register 3 (q2) */ + /* 0x0270 - 0x027c: reserved */ + +/* + * Bank 5 + */ +#define B5_XA_D 0x0280 /* 4*32 bit current transmit Descriptor (xa) */ +#define B5_XA_DA 0x0290 /* 32 bit current tx desc address (xa) */ +#define B5_XA_AC 0x0294 /* 32 bit current tx Address Count (xa) */ +#define B5_XA_BC 0x0298 /* 32 bit current tx Byte Counter (xa) */ +#define B5_XA_CSR 0x029c /* 32 bit BMU Control/Status Register (xa) */ +#define B5_XA_F 0x02a0 /* 32 bit flag register (xa) */ +#define B5_XA_T1 0x02a4 /* 32 bit Test Register 1 (xa) */ +#define B5_XA_T1_TR 0x02a4 /* 8 bit Test Register 1 TR (xa) */ +#define B5_XA_T1_WR 0x02a5 /* 8 bit Test Register 1 WR (xa) */ +#define B5_XA_T1_RD 0x02a6 /* 8 bit Test Register 1 RD (xa) */ +#define B5_XA_T1_SV 0x02a7 /* 8 bit Test Register 1 SV (xa) */ +#define B5_XA_T2 0x02a8 /* 32 bit Test Register 2 (xa) */ +#define B5_XA_T3 0x02ac /* 32 bit Test Register 3 (xa) */ +#define B5_XA_DA_H 0x02b0 /* (ML) 32 bit Curr Tx Desc Address High */ +#define B5_XA_AC_H 0x02b4 /* (ML) 32 bit Curr Addr Counter High dword */ + /* 0x02b8 - 0x02bc: reserved */ +#define B5_XS_D 0x02c0 /* 4*32 bit current transmit Descriptor (xs) */ +#define B5_XS_DA 0x02d0 /* 32 bit current tx desc address (xs) */ +#define B5_XS_AC 0x02d4 /* 32 bit current transmit Address Count(xs) */ +#define B5_XS_BC 0x02d8 /* 32 bit current transmit Byte Counter (xs) */ +#define B5_XS_CSR 0x02dc /* 32 bit BMU Control/Status Register (xs) */ +#define B5_XS_F 0x02e0 /* 32 bit flag register (xs) */ +#define B5_XS_T1 0x02e4 /* 32 bit Test Register 1 (xs) */ +#define B5_XS_T1_TR 0x02e4 /* 8 bit Test Register 1 TR (xs) */ +#define B5_XS_T1_WR 0x02e5 /* 8 bit Test Register 1 WR (xs) */ +#define B5_XS_T1_RD 0x02e6 /* 8 bit Test Register 1 RD (xs) */ +#define B5_XS_T1_SV 0x02e7 /* 8 bit Test Register 1 SV (xs) */ +#define B5_XS_T2 0x02e8 /* 32 bit Test Register 2 (xs) */ +#define B5_XS_T3 0x02ec /* 32 bit Test Register 3 (xs) */ +#define B5_XS_DA_H 0x02f0 /* (ML) 32 bit Curr Tx Desc Address High */ +#define B5_XS_AC_H 0x02f4 /* (ML) 32 bit Curr Addr Counter High dword */ + /* 0x02f8 - 0x02fc: reserved */ + +/* + * Bank 6 + */ +/* External PLC-S registers (SN2 compatibility for DV) */ +/* External registers (ML) */ +#define B6_EXT_REG 0x300 + +/* + * Bank 7 + */ +/* DAS PLC-S Registers */ + +/* + * Bank 8 - 15 + */ +/* IFCP registers */ + +/*---------------------------------------------------------------------------*/ +/* Definitions of the Bits in the registers */ + +/* B0_RAP 16 bit register address port */ +#define RAP_RAP 0x0f /* Bit 3..0: 0 = block0, .., f = block15 */ + +/* B0_CTRL 8 bit control register */ +#define CTRL_FDDI_CLR (1<<7) /* Bit 7: (ML) Clear FDDI Reset */ +#define CTRL_FDDI_SET (1<<6) /* Bit 6: (ML) Set FDDI Reset */ +#define CTRL_HPI_CLR (1<<5) /* Bit 5: Clear HPI SM reset */ +#define CTRL_HPI_SET (1<<4) /* Bit 4: Set HPI SM reset */ +#define CTRL_MRST_CLR (1<<3) /* Bit 3: Clear Master reset */ +#define CTRL_MRST_SET (1<<2) /* Bit 2: Set Master reset */ +#define CTRL_RST_CLR (1<<1) /* Bit 1: Clear Software reset */ +#define CTRL_RST_SET (1<<0) /* Bit 0: Set Software reset */ + +/* B0_DAS 8 Bit control register (DAS) */ +#define BUS_CLOCK (1<<7) /* Bit 7: (ML) Bus Clock 0/1 = 33/66MHz */ +#define BUS_SLOT_SZ (1<<6) /* Bit 6: (ML) Slot Size 0/1 = 32/64 bit slot*/ + /* Bit 5..4: reserved */ +#define DAS_AVAIL (1<<3) /* Bit 3: 1 = DAS, 0 = SAS */ +#define DAS_BYP_ST (1<<2) /* Bit 2: 1 = avail,SAS, 0 = not avail */ +#define DAS_BYP_INS (1<<1) /* Bit 1: 1 = insert Bypass */ +#define DAS_BYP_RMV (1<<0) /* Bit 0: 1 = remove Bypass */ + +/* B0_LED 8 Bit LED register */ + /* Bit 7..6: reserved */ +#define LED_2_ON (1<<5) /* Bit 5: 1 = switch LED_2 on (left,gn)*/ +#define LED_2_OFF (1<<4) /* Bit 4: 1 = switch LED_2 off */ +#define LED_1_ON (1<<3) /* Bit 3: 1 = switch LED_1 on (mid,yel)*/ +#define LED_1_OFF (1<<2) /* Bit 2: 1 = switch LED_1 off */ +#define LED_0_ON (1<<1) /* Bit 1: 1 = switch LED_0 on (rght,gn)*/ +#define LED_0_OFF (1<<0) /* Bit 0: 1 = switch LED_0 off */ +/* This hardware defines are very ugly therefore we define some others */ + +#define LED_GA_ON LED_2_ON /* S port = A port */ +#define LED_GA_OFF LED_2_OFF /* S port = A port */ +#define LED_MY_ON LED_1_ON +#define LED_MY_OFF LED_1_OFF +#define LED_GB_ON LED_0_ON +#define LED_GB_OFF LED_0_OFF + +/* B0_TST_CTRL 8 bit test control register */ +#define TST_FRC_DPERR_MR (1<<7) /* Bit 7: force DATAPERR on MST RE. */ +#define TST_FRC_DPERR_MW (1<<6) /* Bit 6: force DATAPERR on MST WR. */ +#define TST_FRC_DPERR_TR (1<<5) /* Bit 5: force DATAPERR on TRG RE. */ +#define TST_FRC_DPERR_TW (1<<4) /* Bit 4: force DATAPERR on TRG WR. */ +#define TST_FRC_APERR_M (1<<3) /* Bit 3: force ADDRPERR on MST */ +#define TST_FRC_APERR_T (1<<2) /* Bit 2: force ADDRPERR on TRG */ +#define TST_CFG_WRITE_ON (1<<1) /* Bit 1: ena configuration reg. WR */ +#define TST_CFG_WRITE_OFF (1<<0) /* Bit 0: dis configuration reg. WR */ + +/* B0_ISRC 32 bit Interrupt source register */ + /* Bit 31..28: reserved */ +#define IS_I2C_READY (1L<<27) /* Bit 27: (ML) IRQ on end of I2C tx */ +#define IS_IRQ_SW (1L<<26) /* Bit 26: (ML) SW forced IRQ */ +#define IS_EXT_REG (1L<<25) /* Bit 25: (ML) IRQ from external reg*/ +#define IS_IRQ_STAT (1L<<24) /* Bit 24: IRQ status exception */ + /* PERR, RMABORT, RTABORT DATAPERR */ +#define IS_IRQ_MST_ERR (1L<<23) /* Bit 23: IRQ master error */ + /* RMABORT, RTABORT, DATAPERR */ +#define IS_TIMINT (1L<<22) /* Bit 22: IRQ_TIMER */ +#define IS_TOKEN (1L<<21) /* Bit 21: IRQ_RTM */ +/* + * Note: The DAS is our First Port (!=PA) + */ +#define IS_PLINT1 (1L<<20) /* Bit 20: IRQ_PHY_DAS */ +#define IS_PLINT2 (1L<<19) /* Bit 19: IRQ_IFCP_4 */ +#define IS_MINTR3 (1L<<18) /* Bit 18: IRQ_IFCP_3/IRQ_PHY */ +#define IS_MINTR2 (1L<<17) /* Bit 17: IRQ_IFCP_2/IRQ_MAC_2 */ +#define IS_MINTR1 (1L<<16) /* Bit 16: IRQ_IFCP_1/IRQ_MAC_1 */ +/* Receive Queue 1 */ +#define IS_R1_P (1L<<15) /* Bit 15: Parity Error (q1) */ +#define IS_R1_B (1L<<14) /* Bit 14: End of Buffer (q1) */ +#define IS_R1_F (1L<<13) /* Bit 13: End of Frame (q1) */ +#define IS_R1_C (1L<<12) /* Bit 12: Encoding Error (q1) */ +/* Receive Queue 2 */ +#define IS_R2_P (1L<<11) /* Bit 11: (DV) Parity Error (q2) */ +#define IS_R2_B (1L<<10) /* Bit 10: (DV) End of Buffer (q2) */ +#define IS_R2_F (1L<<9) /* Bit 9: (DV) End of Frame (q2) */ +#define IS_R2_C (1L<<8) /* Bit 8: (DV) Encoding Error (q2) */ +/* Asynchronous Transmit queue */ + /* Bit 7: reserved */ +#define IS_XA_B (1L<<6) /* Bit 6: End of Buffer (xa) */ +#define IS_XA_F (1L<<5) /* Bit 5: End of Frame (xa) */ +#define IS_XA_C (1L<<4) /* Bit 4: Encoding Error (xa) */ +/* Synchronous Transmit queue */ + /* Bit 3: reserved */ +#define IS_XS_B (1L<<2) /* Bit 2: End of Buffer (xs) */ +#define IS_XS_F (1L<<1) /* Bit 1: End of Frame (xs) */ +#define IS_XS_C (1L<<0) /* Bit 0: Encoding Error (xs) */ + +/* + * Define all valid interrupt source Bits from GET_ISR () + */ +#define ALL_IRSR 0x01ffff77L /* (DV) */ +#define ALL_IRSR_ML 0x0ffff077L /* (ML) */ + + +/* B0_IMSK 32 bit Interrupt mask register */ +/* + * The Bit definnition of this register are the same as of the interrupt + * source register. These definition are directly derived from the Hardware + * spec. + */ + /* Bit 31..28: reserved */ +#define IRQ_I2C_READY (1L<<27) /* Bit 27: (ML) IRQ on end of I2C tx */ +#define IRQ_SW (1L<<26) /* Bit 26: (ML) SW forced IRQ */ +#define IRQ_EXT_REG (1L<<25) /* Bit 25: (ML) IRQ from external reg*/ +#define IRQ_STAT (1L<<24) /* Bit 24: IRQ status exception */ + /* PERR, RMABORT, RTABORT DATAPERR */ +#define IRQ_MST_ERR (1L<<23) /* Bit 23: IRQ master error */ + /* RMABORT, RTABORT, DATAPERR */ +#define IRQ_TIMER (1L<<22) /* Bit 22: IRQ_TIMER */ +#define IRQ_RTM (1L<<21) /* Bit 21: IRQ_RTM */ +#define IRQ_DAS (1L<<20) /* Bit 20: IRQ_PHY_DAS */ +#define IRQ_IFCP_4 (1L<<19) /* Bit 19: IRQ_IFCP_4 */ +#define IRQ_IFCP_3 (1L<<18) /* Bit 18: IRQ_IFCP_3/IRQ_PHY */ +#define IRQ_IFCP_2 (1L<<17) /* Bit 17: IRQ_IFCP_2/IRQ_MAC_2 */ +#define IRQ_IFCP_1 (1L<<16) /* Bit 16: IRQ_IFCP_1/IRQ_MAC_1 */ +/* Receive Queue 1 */ +#define IRQ_R1_P (1L<<15) /* Bit 15: Parity Error (q1) */ +#define IRQ_R1_B (1L<<14) /* Bit 14: End of Buffer (q1) */ +#define IRQ_R1_F (1L<<13) /* Bit 13: End of Frame (q1) */ +#define IRQ_R1_C (1L<<12) /* Bit 12: Encoding Error (q1) */ +/* Receive Queue 2 */ +#define IRQ_R2_P (1L<<11) /* Bit 11: (DV) Parity Error (q2) */ +#define IRQ_R2_B (1L<<10) /* Bit 10: (DV) End of Buffer (q2) */ +#define IRQ_R2_F (1L<<9) /* Bit 9: (DV) End of Frame (q2) */ +#define IRQ_R2_C (1L<<8) /* Bit 8: (DV) Encoding Error (q2) */ +/* Asynchronous Transmit queue */ + /* Bit 7: reserved */ +#define IRQ_XA_B (1L<<6) /* Bit 6: End of Buffer (xa) */ +#define IRQ_XA_F (1L<<5) /* Bit 5: End of Frame (xa) */ +#define IRQ_XA_C (1L<<4) /* Bit 4: Encoding Error (xa) */ +/* Synchronous Transmit queue */ + /* Bit 3: reserved */ +#define IRQ_XS_B (1L<<2) /* Bit 2: End of Buffer (xs) */ +#define IRQ_XS_F (1L<<1) /* Bit 1: End of Frame (xs) */ +#define IRQ_XS_C (1L<<0) /* Bit 0: Encoding Error (xs) */ + +/* 0x0010 - 0x006b: formac+ (supernet_3) fequently used registers */ +/* B0_R1_CSR 32 bit BMU control/status reg (rec q 1 ) */ +/* B0_R2_CSR 32 bit BMU control/status reg (rec q 2 ) */ +/* B0_XA_CSR 32 bit BMU control/status reg (a xmit q ) */ +/* B0_XS_CSR 32 bit BMU control/status reg (s xmit q ) */ +/* The registers are the same as B4_R1_CSR, B4_R2_CSR, B5_Xa_CSR, B5_XS_CSR */ + +/* B2_MAC_0 8 bit MAC address Byte 0 */ +/* B2_MAC_1 8 bit MAC address Byte 1 */ +/* B2_MAC_2 8 bit MAC address Byte 2 */ +/* B2_MAC_3 8 bit MAC address Byte 3 */ +/* B2_MAC_4 8 bit MAC address Byte 4 */ +/* B2_MAC_5 8 bit MAC address Byte 5 */ +/* B2_MAC_6 8 bit MAC address Byte 6 (== 0) (DV) */ +/* B2_MAC_7 8 bit MAC address Byte 7 (== 0) (DV) */ + +/* B2_CONN_TYP 8 bit Connector type */ +/* B2_PMD_TYP 8 bit PMD type */ +/* Values of connector and PMD type comply to SysKonnect internal std */ + +/* The EPROM register are currently of no use */ +/* B2_E_0 8 bit EPROM Byte 0 */ +/* B2_E_1 8 bit EPROM Byte 1 */ +/* B2_E_2 8 bit EPROM Byte 2 */ +/* B2_E_3 8 bit EPROM Byte 3 */ + +/* B2_FAR 32 bit Flash-Prom Address Register/Counter */ +#define FAR_ADDR 0x1ffffL /* Bit 16..0: FPROM Address mask */ + +/* B2_FDP 8 bit Flash-Prom Data Port */ + +/* B2_LD_CRTL 8 bit loader control */ +/* Bits are currently reserved */ + +/* B2_LD_TEST 8 bit loader test */ +#define LD_T_ON (1<<3) /* Bit 3: Loader Testmode on */ +#define LD_T_OFF (1<<2) /* Bit 2: Loader Testmode off */ +#define LD_T_STEP (1<<1) /* Bit 1: Decrement FPROM addr. Counter */ +#define LD_START (1<<0) /* Bit 0: Start loading FPROM */ + +/* B2_TI_INI 32 bit Timer init value */ +/* B2_TI_VAL 32 bit Timer value */ +/* B2_TI_CRTL 8 bit Timer control */ +/* B2_TI_TEST 8 Bit Timer Test */ +/* B2_WDOG_INI 32 bit Watchdog init value */ +/* B2_WDOG_VAL 32 bit Watchdog value */ +/* B2_WDOG_CRTL 8 bit Watchdog control */ +/* B2_WDOG_TEST 8 Bit Watchdog Test */ +/* B2_RTM_INI 32 bit RTM init value */ +/* B2_RTM_VAL 32 bit RTM value */ +/* B2_RTM_CRTL 8 bit RTM control */ +/* B2_RTM_TEST 8 Bit RTM Test */ +/* B2_<TIM>_CRTL 8 bit <TIM> control */ +/* B2_IRQ_MOD_INI 32 bit IRQ Moderation Timer Init Reg. (ML) */ +/* B2_IRQ_MOD_VAL 32 bit IRQ Moderation Timer Value (ML) */ +/* B2_IRQ_MOD_CTRL 8 bit IRQ Moderation Timer Control (ML) */ +/* B2_IRQ_MOD_TEST 8 bit IRQ Moderation Timer Test (ML) */ +#define GET_TOK_CT (1<<4) /* Bit 4: Get the Token Counter (RTM) */ +#define TIM_RES_TOK (1<<3) /* Bit 3: RTM Status: 1 == restricted */ +#define TIM_ALARM (1<<3) /* Bit 3: Timer Alarm (WDOG) */ +#define TIM_START (1<<2) /* Bit 2: Start Timer (TI,WDOG,RTM,IRQ_MOD)*/ +#define TIM_STOP (1<<1) /* Bit 1: Stop Timer (TI,WDOG,RTM,IRQ_MOD) */ +#define TIM_CL_IRQ (1<<0) /* Bit 0: Clear Timer IRQ (TI,WDOG,RTM) */ +/* B2_<TIM>_TEST 8 Bit <TIM> Test */ +#define TIM_T_ON (1<<2) /* Bit 2: Test mode on (TI,WDOG,RTM,IRQ_MOD) */ +#define TIM_T_OFF (1<<1) /* Bit 1: Test mode off (TI,WDOG,RTM,IRQ_MOD) */ +#define TIM_T_STEP (1<<0) /* Bit 0: Test step (TI,WDOG,RTM,IRQ_MOD) */ + +/* B2_TOK_COUNT 0x014c (ML) 32 bit Token Counter */ +/* B2_DESC_ADDR_H 0x0150 (ML) 32 bit Desciptor Base Addr Reg High */ +/* B2_CTRL_2 0x0154 (ML) 8 bit Control Register 2 */ + /* Bit 7..5: reserved */ +#define CTRL_CL_I2C_IRQ (1<<4) /* Bit 4: Clear I2C IRQ */ +#define CTRL_ST_SW_IRQ (1<<3) /* Bit 3: Set IRQ SW Request */ +#define CTRL_CL_SW_IRQ (1<<2) /* Bit 2: Clear IRQ SW Request */ +#define CTRL_STOP_DONE (1<<1) /* Bit 1: Stop Master is finished */ +#define CTRL_STOP_MAST (1<<0) /* Bit 0: Command Bit to stop the master*/ + +/* B2_IFACE_REG 0x0155 (ML) 8 bit Interface Register */ + /* Bit 7..3: reserved */ +#define IF_I2C_DATA_DIR (1<<2) /* Bit 2: direction of IF_I2C_DATA*/ +#define IF_I2C_DATA (1<<1) /* Bit 1: I2C Data Port */ +#define IF_I2C_CLK (1<<0) /* Bit 0: I2C Clock Port */ + + /* 0x0156: reserved */ +/* B2_TST_CTRL_2 0x0157 (ML) 8 bit Test Control Register 2 */ + /* Bit 7..4: reserved */ + /* force the following error on */ + /* the next master read/write */ +#define TST_FRC_DPERR_MR64 (1<<3) /* Bit 3: DataPERR RD 64 */ +#define TST_FRC_DPERR_MW64 (1<<2) /* Bit 2: DataPERR WR 64 */ +#define TST_FRC_APERR_1M64 (1<<1) /* Bit 1: AddrPERR on 1. phase */ +#define TST_FRC_APERR_2M64 (1<<0) /* Bit 0: AddrPERR on 2. phase */ + +/* B2_I2C_CTRL 0x0158 (ML) 32 bit I2C Control Register */ +#define I2C_FLAG (1L<<31) /* Bit 31: Start read/write if WR */ +#define I2C_ADDR (0x7fffL<<16) /* Bit 30..16: Addr to be read/written*/ +#define I2C_DEV_SEL (0x7fL<<9) /* Bit 9..15: I2C Device Select */ + /* Bit 5.. 8: reserved */ +#define I2C_BURST_LEN (1L<<4) /* Bit 4 Burst Len, 1/4 bytes */ +#define I2C_DEV_SIZE (7L<<1) /* Bit 1.. 3: I2C Device Size */ +#define I2C_025K_DEV (0L<<1) /* 0: 256 Bytes or smaller*/ +#define I2C_05K_DEV (1L<<1) /* 1: 512 Bytes */ +#define I2C_1K_DEV (2L<<1) /* 2: 1024 Bytes */ +#define I2C_2K_DEV (3L<<1) /* 3: 2048 Bytes */ +#define I2C_4K_DEV (4L<<1) /* 4: 4096 Bytes */ +#define I2C_8K_DEV (5L<<1) /* 5: 8192 Bytes */ +#define I2C_16K_DEV (6L<<1) /* 6: 16384 Bytes */ +#define I2C_32K_DEV (7L<<1) /* 7: 32768 Bytes */ +#define I2C_STOP_BIT (1<<0) /* Bit 0: Interrupt I2C transfer */ + +/* + * I2C Addresses + * + * The temperature sensor and the voltage sensor are on the same I2C bus. + * Note: The voltage sensor (Micorwire) will be selected by PCI_EXT_PATCH_1 + * in PCI_OUR_REG 1. + */ +#define I2C_ADDR_TEMP 0x90 /* I2C Address Temperature Sensor */ + +/* B2_I2C_DATA 0x015c (ML) 32 bit I2C Data Register */ + +/* B4_R1_D 4*32 bit current receive Descriptor (q1) */ +/* B4_R1_DA 32 bit current rec desc address (q1) */ +/* B4_R1_AC 32 bit current receive Address Count (q1) */ +/* B4_R1_BC 32 bit current receive Byte Counter (q1) */ +/* B4_R1_CSR 32 bit BMU Control/Status Register (q1) */ +/* B4_R1_F 32 bit flag register (q1) */ +/* B4_R1_T1 32 bit Test Register 1 (q1) */ +/* B4_R1_T2 32 bit Test Register 2 (q1) */ +/* B4_R1_T3 32 bit Test Register 3 (q1) */ +/* B4_R2_D 4*32 bit current receive Descriptor (q2) */ +/* B4_R2_DA 32 bit current rec desc address (q2) */ +/* B4_R2_AC 32 bit current receive Address Count (q2) */ +/* B4_R2_BC 32 bit current receive Byte Counter (q2) */ +/* B4_R2_CSR 32 bit BMU Control/Status Register (q2) */ +/* B4_R2_F 32 bit flag register (q2) */ +/* B4_R2_T1 32 bit Test Register 1 (q2) */ +/* B4_R2_T2 32 bit Test Register 2 (q2) */ +/* B4_R2_T3 32 bit Test Register 3 (q2) */ +/* B5_XA_D 4*32 bit current receive Descriptor (xa) */ +/* B5_XA_DA 32 bit current rec desc address (xa) */ +/* B5_XA_AC 32 bit current receive Address Count (xa) */ +/* B5_XA_BC 32 bit current receive Byte Counter (xa) */ +/* B5_XA_CSR 32 bit BMU Control/Status Register (xa) */ +/* B5_XA_F 32 bit flag register (xa) */ +/* B5_XA_T1 32 bit Test Register 1 (xa) */ +/* B5_XA_T2 32 bit Test Register 2 (xa) */ +/* B5_XA_T3 32 bit Test Register 3 (xa) */ +/* B5_XS_D 4*32 bit current receive Descriptor (xs) */ +/* B5_XS_DA 32 bit current rec desc address (xs) */ +/* B5_XS_AC 32 bit current receive Address Count (xs) */ +/* B5_XS_BC 32 bit current receive Byte Counter (xs) */ +/* B5_XS_CSR 32 bit BMU Control/Status Register (xs) */ +/* B5_XS_F 32 bit flag register (xs) */ +/* B5_XS_T1 32 bit Test Register 1 (xs) */ +/* B5_XS_T2 32 bit Test Register 2 (xs) */ +/* B5_XS_T3 32 bit Test Register 3 (xs) */ +/* B5_<xx>_CSR 32 bit BMU Control/Status Register (xx) */ +#define CSR_DESC_CLEAR (1L<<21) /* Bit 21: Clear Reset for Descr */ +#define CSR_DESC_SET (1L<<20) /* Bit 20: Set Reset for Descr */ +#define CSR_FIFO_CLEAR (1L<<19) /* Bit 19: Clear Reset for FIFO */ +#define CSR_FIFO_SET (1L<<18) /* Bit 18: Set Reset for FIFO */ +#define CSR_HPI_RUN (1L<<17) /* Bit 17: Release HPI SM */ +#define CSR_HPI_RST (1L<<16) /* Bit 16: Reset HPI SM to Idle */ +#define CSR_SV_RUN (1L<<15) /* Bit 15: Release Supervisor SM */ +#define CSR_SV_RST (1L<<14) /* Bit 14: Reset Supervisor SM */ +#define CSR_DREAD_RUN (1L<<13) /* Bit 13: Release Descr Read SM */ +#define CSR_DREAD_RST (1L<<12) /* Bit 12: Reset Descr Read SM */ +#define CSR_DWRITE_RUN (1L<<11) /* Bit 11: Rel. Descr Write SM */ +#define CSR_DWRITE_RST (1L<<10) /* Bit 10: Reset Descr Write SM */ +#define CSR_TRANS_RUN (1L<<9) /* Bit 9: Release Transfer SM */ +#define CSR_TRANS_RST (1L<<8) /* Bit 8: Reset Transfer SM */ + /* Bit 7..5: reserved */ +#define CSR_START (1L<<4) /* Bit 4: Start Rec/Xmit Queue */ +#define CSR_IRQ_CL_P (1L<<3) /* Bit 3: Clear Parity IRQ, Rcv */ +#define CSR_IRQ_CL_B (1L<<2) /* Bit 2: Clear EOB IRQ */ +#define CSR_IRQ_CL_F (1L<<1) /* Bit 1: Clear EOF IRQ */ +#define CSR_IRQ_CL_C (1L<<0) /* Bit 0: Clear ERR IRQ */ + +#define CSR_SET_RESET (CSR_DESC_SET|CSR_FIFO_SET|CSR_HPI_RST|CSR_SV_RST|\ + CSR_DREAD_RST|CSR_DWRITE_RST|CSR_TRANS_RST) +#define CSR_CLR_RESET (CSR_DESC_CLEAR|CSR_FIFO_CLEAR|CSR_HPI_RUN|CSR_SV_RUN|\ + CSR_DREAD_RUN|CSR_DWRITE_RUN|CSR_TRANS_RUN) + + +/* B5_<xx>_F 32 bit flag register (xx) */ + /* Bit 28..31: reserved */ +#define F_ALM_FULL (1L<<27) /* Bit 27: (ML) FIFO almost full */ +#define F_FIFO_EOF (1L<<26) /* Bit 26: (ML) Fag bit in FIFO */ +#define F_WM_REACHED (1L<<25) /* Bit 25: (ML) Watermark reached */ +#define F_UP_DW_USED (1L<<24) /* Bit 24: (ML) Upper Dword used (bug)*/ + /* Bit 23: reserved */ +#define F_FIFO_LEVEL (0x1fL<<16) /* Bit 16..22:(ML) # of Qwords in FIFO*/ + /* Bit 8..15: reserved */ +#define F_ML_WATER_M 0x0000ffL /* Bit 0.. 7:(ML) Watermark */ +#define FLAG_WATER 0x00001fL /* Bit 4..0:(DV) Level of req data tr.*/ + +/* B5_<xx>_T1 32 bit Test Register 1 (xx) */ +/* Holds four State Machine control Bytes */ +#define SM_CRTL_SV (0xffL<<24) /* Bit 31..24: Control Supervisor SM */ +#define SM_CRTL_RD (0xffL<<16) /* Bit 23..16: Control Read Desc SM */ +#define SM_CRTL_WR (0xffL<<8) /* Bit 15..8: Control Write Desc SM */ +#define SM_CRTL_TR (0xffL<<0) /* Bit 7..0: Control Transfer SM */ + +/* B4_<xx>_T1_TR 8 bit Test Register 1 TR (xx) */ +/* B4_<xx>_T1_WR 8 bit Test Register 1 WR (xx) */ +/* B4_<xx>_T1_RD 8 bit Test Register 1 RD (xx) */ +/* B4_<xx>_T1_SV 8 bit Test Register 1 SV (xx) */ +/* The control status byte of each machine looks like ... */ +#define SM_STATE 0xf0 /* Bit 7..4: State which shall be loaded */ +#define SM_LOAD 0x08 /* Bit 3: Load the SM with SM_STATE */ +#define SM_TEST_ON 0x04 /* Bit 2: Switch on SM Test Mode */ +#define SM_TEST_OFF 0x02 /* Bit 1: Go off the Test Mode */ +#define SM_STEP 0x01 /* Bit 0: Step the State Machine */ + +/* The coding of the states */ +#define SM_SV_IDLE 0x0 /* Supervisor Idle Tr/Re */ +#define SM_SV_RES_START 0x1 /* Supervisor Res_Start Tr/Re */ +#define SM_SV_GET_DESC 0x3 /* Supervisor Get_Desc Tr/Re */ +#define SM_SV_CHECK 0x2 /* Supervisor Check Tr/Re */ +#define SM_SV_MOV_DATA 0x6 /* Supervisor Move_Data Tr/Re */ +#define SM_SV_PUT_DESC 0x7 /* Supervisor Put_Desc Tr/Re */ +#define SM_SV_SET_IRQ 0x5 /* Supervisor Set_Irq Tr/Re */ + +#define SM_RD_IDLE 0x0 /* Read Desc. Idle Tr/Re */ +#define SM_RD_LOAD 0x1 /* Read Desc. Load Tr/Re */ +#define SM_RD_WAIT_TC 0x3 /* Read Desc. Wait_TC Tr/Re */ +#define SM_RD_RST_EOF 0x6 /* Read Desc. Reset_EOF Re */ +#define SM_RD_WDONE_R 0x2 /* Read Desc. Wait_Done Re */ +#define SM_RD_WDONE_T 0x4 /* Read Desc. Wait_Done Tr */ + +#define SM_TR_IDLE 0x0 /* Trans. Data Idle Tr/Re */ +#define SM_TR_LOAD 0x3 /* Trans. Data Load Tr/Re */ +#define SM_TR_LOAD_R_ML 0x1 /* Trans. Data Load /Re (ML) */ +#define SM_TR_WAIT_TC 0x2 /* Trans. Data Wait_TC Tr/Re */ +#define SM_TR_WDONE 0x4 /* Trans. Data Wait_Done Tr/Re */ + +#define SM_WR_IDLE 0x0 /* Write Desc. Idle Tr/Re */ +#define SM_WR_ABLEN 0x1 /* Write Desc. Act_Buf_Length Tr/Re */ +#define SM_WR_LD_A4 0x2 /* Write Desc. Load_A4 Re */ +#define SM_WR_RES_OWN 0x2 /* Write Desc. Res_OWN Tr */ +#define SM_WR_WAIT_EOF 0x3 /* Write Desc. Wait_EOF Re */ +#define SM_WR_LD_N2C_R 0x4 /* Write Desc. Load_N2C Re */ +#define SM_WR_WAIT_TC_R 0x5 /* Write Desc. Wait_TC Re */ +#define SM_WR_WAIT_TC4 0x6 /* Write Desc. Wait_TC4 Re */ +#define SM_WR_LD_A_T 0x6 /* Write Desc. Load_A Tr */ +#define SM_WR_LD_A_R 0x7 /* Write Desc. Load_A Re */ +#define SM_WR_WAIT_TC_T 0x7 /* Write Desc. Wait_TC Tr */ +#define SM_WR_LD_N2C_T 0xc /* Write Desc. Load_N2C Tr */ +#define SM_WR_WDONE_T 0x9 /* Write Desc. Wait_Done Tr */ +#define SM_WR_WDONE_R 0xc /* Write Desc. Wait_Done Re */ +#define SM_WR_LD_D_AD 0xe /* Write Desc. Load_Dumr_A Re (ML) */ +#define SM_WR_WAIT_D_TC 0xf /* Write Desc. Wait_Dumr_TC Re (ML) */ + +/* B5_<xx>_T2 32 bit Test Register 2 (xx) */ +/* Note: This register is only defined for the transmit queues */ + /* Bit 31..8: reserved */ +#define AC_TEST_ON (1<<7) /* Bit 7: Address Counter Test Mode on */ +#define AC_TEST_OFF (1<<6) /* Bit 6: Address Counter Test Mode off*/ +#define BC_TEST_ON (1<<5) /* Bit 5: Byte Counter Test Mode on */ +#define BC_TEST_OFF (1<<4) /* Bit 4: Byte Counter Test Mode off */ +#define TEST_STEP04 (1<<3) /* Bit 3: Inc AC/Dec BC by 4 */ +#define TEST_STEP03 (1<<2) /* Bit 2: Inc AC/Dec BC by 3 */ +#define TEST_STEP02 (1<<1) /* Bit 1: Inc AC/Dec BC by 2 */ +#define TEST_STEP01 (1<<0) /* Bit 0: Inc AC/Dec BC by 1 */ + +/* B5_<xx>_T3 32 bit Test Register 3 (xx) */ +/* Note: This register is only defined for the transmit queues */ + /* Bit 31..8: reserved */ +#define T3_MUX_2 (1<<7) /* Bit 7: (ML) Mux position MSB */ +#define T3_VRAM_2 (1<<6) /* Bit 6: (ML) Virtual RAM buffer addr MSB */ +#define T3_LOOP (1<<5) /* Bit 5: Set Loopback (Xmit) */ +#define T3_UNLOOP (1<<4) /* Bit 4: Unset Loopback (Xmit) */ +#define T3_MUX (3<<2) /* Bit 3..2: Mux position */ +#define T3_VRAM (3<<0) /* Bit 1..0: Virtual RAM buffer Address */ + +/* PCI card IDs */ +/* + * Note: The following 4 byte definitions shall not be used! Use OEM Concept! + */ +#define PCI_VEND_ID0 0x48 /* PCI vendor ID (SysKonnect) */ +#define PCI_VEND_ID1 0x11 /* PCI vendor ID (SysKonnect) */ + /* (High byte) */ +#define PCI_DEV_ID0 0x00 /* PCI device ID */ +#define PCI_DEV_ID1 0x40 /* PCI device ID (High byte) */ + +/*#define PCI_CLASS 0x02*/ /* PCI class code: network device */ +#define PCI_NW_CLASS 0x02 /* PCI class code: network device */ +#define PCI_SUB_CLASS 0x02 /* PCI subclass ID: FDDI device */ +#define PCI_PROG_INTFC 0x00 /* PCI programming Interface (=0) */ + +/* + * address transmission from logical to physical offset address on board + */ +#define FMA(a) (0x0400|((a)<<2)) /* FORMAC+ (r/w) (SN3) */ +#define P1(a) (0x0380|((a)<<2)) /* PLC1 (r/w) (DAS) */ +#define P2(a) (0x0600|((a)<<2)) /* PLC2 (r/w) (covered by the SN3) */ +#define PRA(a) (B2_MAC_0 + (a)) /* configuration PROM (MAC address) */ + +/* + * FlashProm specification + */ +#define MAX_PAGES 0x20000L /* Every byte has a single page */ +#define MAX_FADDR 1 /* 1 byte per page */ + +/* + * Receive / Transmit Buffer Control word + */ +#define BMU_OWN (1UL<<31) /* OWN bit: 0 == host, 1 == adapter */ +#define BMU_STF (1L<<30) /* Start of Frame ? */ +#define BMU_EOF (1L<<29) /* End of Frame ? */ +#define BMU_EN_IRQ_EOB (1L<<28) /* Enable "End of Buffer" IRQ */ +#define BMU_EN_IRQ_EOF (1L<<27) /* Enable "End of Frame" IRQ */ +#define BMU_DEV_0 (1L<<26) /* RX: don't transfer to system mem */ +#define BMU_SMT_TX (1L<<25) /* TX: if set, buffer type SMT_MBuf */ +#define BMU_ST_BUF (1L<<25) /* RX: copy of start of frame */ +#define BMU_UNUSED (1L<<24) /* Set if the Descr is curr unused */ +#define BMU_SW (3L<<24) /* 2 Bits reserved for SW usage */ +#define BMU_CHECK 0x00550000L /* To identify the control word */ +#define BMU_BBC 0x0000FFFFL /* R/T Buffer Byte Count */ + +/* + * physical address offset + IO-Port base address + */ +#ifdef MEM_MAPPED_IO +#define ADDR(a) (char far *) smc->hw.iop+(a) +#define ADDRS(smc,a) (char far *) (smc)->hw.iop+(a) +#else +#define ADDR(a) (((a)>>7) ? (outp(smc->hw.iop+B0_RAP,(a)>>7), \ + (smc->hw.iop+(((a)&0x7F)|((a)>>7 ? 0x80:0)))) : \ + (smc->hw.iop+(((a)&0x7F)|((a)>>7 ? 0x80:0)))) +#define ADDRS(smc,a) (((a)>>7) ? (outp((smc)->hw.iop+B0_RAP,(a)>>7), \ + ((smc)->hw.iop+(((a)&0x7F)|((a)>>7 ? 0x80:0)))) : \ + ((smc)->hw.iop+(((a)&0x7F)|((a)>>7 ? 0x80:0)))) +#endif + +/* + * Define a macro to access the configuration space + */ +#define PCI_C(a) ADDR(B3_CFG_SPC + (a)) /* PCI Config Space */ + +#define EXT_R(a) ADDR(B6_EXT_REG + (a)) /* External Registers */ + +/* + * Define some values needed for the MAC address (PROM) + */ +#define SA_MAC (0) /* start addr. MAC_AD within the PROM */ +#define PRA_OFF (0) /* offset correction when 4th byte reading */ + +#define SKFDDI_PSZ 8 /* address PROM size */ + +#define FM_A(a) ADDR(FMA(a)) /* FORMAC Plus physical addr */ +#define P1_A(a) ADDR(P1(a)) /* PLC1 (r/w) */ +#define P2_A(a) ADDR(P2(a)) /* PLC2 (r/w) (DAS) */ +#define PR_A(a) ADDR(PRA(a)) /* config. PROM (MAC address) */ + +/* + * Macro to read the PROM + */ +#define READ_PROM(a) ((u_char)inp(a)) + +#define GET_PAGE(bank) outpd(ADDR(B2_FAR),bank) +#define VPP_ON() +#define VPP_OFF() + +/* + * Note: Values of the Interrupt Source Register are defined above + */ +#define ISR_A ADDR(B0_ISRC) +#define GET_ISR() inpd(ISR_A) +#define GET_ISR_SMP(iop) inpd((iop)+B0_ISRC) +#define CHECK_ISR() (inpd(ISR_A) & inpd(ADDR(B0_IMSK))) +#define CHECK_ISR_SMP(iop) (inpd((iop)+B0_ISRC) & inpd((iop)+B0_IMSK)) + +#define BUS_CHECK() + +/* + * CLI_FBI: Disable Board Interrupts + * STI_FBI: Enable Board Interrupts + */ +#ifndef UNIX +#define CLI_FBI() outpd(ADDR(B0_IMSK),0) +#else +#define CLI_FBI(smc) outpd(ADDRS((smc),B0_IMSK),0) +#endif + +#ifndef UNIX +#define STI_FBI() outpd(ADDR(B0_IMSK),smc->hw.is_imask) +#else +#define STI_FBI(smc) outpd(ADDRS((smc),B0_IMSK),(smc)->hw.is_imask) +#endif + +#define CLI_FBI_SMP(iop) outpd((iop)+B0_IMSK,0) +#define STI_FBI_SMP(smc,iop) outpd((iop)+B0_IMSK,(smc)->hw.is_imask) + +#endif /* PCI */ +/*--------------------------------------------------------------------------*/ + +/* + * 12 bit transfer (dword) counter: + * (ISA: 2*trc = number of byte) + * (EISA: 4*trc = number of byte) + * (MCA: 4*trc = number of byte) + */ +#define MAX_TRANS (0x0fff) + +/* + * PC PIC + */ +#define MST_8259 (0x20) +#define SLV_8259 (0xA0) + +#define TPS (18) /* ticks per second */ + +/* + * error timer defs + */ +#define TN (4) /* number of supported timer = TN+1 */ +#define SNPPND_TIME (5) /* buffer memory access over mem. data reg. */ + +#define MAC_AD 0x405a0000 + +#define MODR1 FM_A(FM_MDREG1) /* mode register 1 */ +#define MODR2 FM_A(FM_MDREG2) /* mode register 2 */ + +#define CMDR1 FM_A(FM_CMDREG1) /* command register 1 */ +#define CMDR2 FM_A(FM_CMDREG2) /* command register 2 */ + + +/* + * function defines + */ +#define CLEAR(io,mask) outpw((io),inpw(io)&(~(mask))) +#define SET(io,mask) outpw((io),inpw(io)|(mask)) +#define GET(io,mask) (inpw(io)&(mask)) +#define SETMASK(io,val,mask) outpw((io),(inpw(io) & ~(mask)) | (val)) + +/* + * PHY Port A (PA) = PLC 1 + * With SuperNet 3 PHY-A and PHY S are identical. + */ +#define PLC(np,reg) (((np) == PA) ? P2_A(reg) : P1_A(reg)) + +/* + * set memory address register for write and read + */ +#define MARW(ma) outpw(FM_A(FM_MARW),(unsigned int)(ma)) +#define MARR(ma) outpw(FM_A(FM_MARR),(unsigned int)(ma)) + +/* + * read/write from/to memory data register + */ +/* write double word */ +#define MDRW(dd) outpw(FM_A(FM_MDRU),(unsigned int)((dd)>>16)) ;\ + outpw(FM_A(FM_MDRL),(unsigned int)(dd)) + +#ifndef WINNT +/* read double word */ +#define MDRR() (((long)inpw(FM_A(FM_MDRU))<<16) + inpw(FM_A(FM_MDRL))) + +/* read FORMAC+ 32-bit status register */ +#define GET_ST1() (((long)inpw(FM_A(FM_ST1U))<<16) + inpw(FM_A(FM_ST1L))) +#define GET_ST2() (((long)inpw(FM_A(FM_ST2U))<<16) + inpw(FM_A(FM_ST2L))) +#ifdef SUPERNET_3 +#define GET_ST3() (((long)inpw(FM_A(FM_ST3U))<<16) + inpw(FM_A(FM_ST3L))) +#endif +#else +/* read double word */ +#define MDRR() inp2w((FM_A(FM_MDRU)),(FM_A(FM_MDRL))) + +/* read FORMAC+ 32-bit status register */ +#define GET_ST1() inp2w((FM_A(FM_ST1U)),(FM_A(FM_ST1L))) +#define GET_ST2() inp2w((FM_A(FM_ST2U)),(FM_A(FM_ST2L))) +#ifdef SUPERNET_3 +#define GET_ST3() inp2w((FM_A(FM_ST3U)),(FM_A(FM_ST3L))) +#endif +#endif + +/* Special timer macro for 82c54 */ + /* timer access over data bus bit 8..15 */ +#define OUT_82c54_TIMER(port,val) outpw(TI_A(port),(val)<<8) +#define IN_82c54_TIMER(port) ((inpw(TI_A(port))>>8) & 0xff) + + +#ifdef DEBUG +#define DB_MAC(mac,st) {if (debug_mac & 0x1)\ + printf("M") ;\ + if (debug_mac & 0x2)\ + printf("\tMAC %d status 0x%08lx\n",mac,st) ;\ + if (debug_mac & 0x4)\ + dp_mac(mac,st) ;\ +} + +#define DB_PLC(p,iev) { if (debug_plc & 0x1)\ + printf("P") ;\ + if (debug_plc & 0x2)\ + printf("\tPLC %s Int 0x%04x\n", \ + (p == PA) ? "A" : "B", iev) ;\ + if (debug_plc & 0x4)\ + dp_plc(p,iev) ;\ +} + +#define DB_TIMER() { if (debug_timer & 0x1)\ + printf("T") ;\ + if (debug_timer & 0x2)\ + printf("\tTimer ISR\n") ;\ +} + +#else /* no DEBUG */ + +#define DB_MAC(mac,st) +#define DB_PLC(p,iev) +#define DB_TIMER() + +#endif /* no DEBUG */ + +#define INC_PTR(sp,cp,ep) if (++cp == ep) cp = sp +/* + * timer defs + */ +#define COUNT(t) ((t)<<6) /* counter */ +#define RW_OP(o) ((o)<<4) /* read/write operation */ +#define TMODE(m) ((m)<<1) /* timer mode */ + +#endif diff --git a/kernel/drivers/net/fddi/skfp/h/skfbiinc.h b/kernel/drivers/net/fddi/skfp/h/skfbiinc.h new file mode 100644 index 000000000..ce72557c3 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/skfbiinc.h @@ -0,0 +1,97 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _SKFBIINC_ +#define _SKFBIINC_ + +#include "supern_2.h" + +/* + * special defines for use into .asm files + */ +#define ERR_FLAGS (FS_MSRABT | FS_SEAC2 | FS_SFRMERR | FS_SFRMTY1) + +#ifdef PCI +#define IMASK_FAST (IS_PLINT1 | IS_PLINT2 | IS_TIMINT | IS_TOKEN | \ + IS_MINTR2 | IS_MINTR3 | IS_R1_P | \ + IS_R1_C | IS_XA_C | IS_XS_C) +#endif + +#ifdef PCI +#define ISR_MASK (IS_MINTR1 | IS_R1_F | IS_XS_F| IS_XA_F | IMASK_FAST) +#else +#define ISR_MASK (IS_MINTR1 | IS_MINTR2 | IMASK_FAST) +#endif + +#define FMA_FM_CMDREG1 FMA(FM_CMDREG1) +#define FMA_FM_CMDREG2 FMA(FM_CMDREG2) +#define FMA_FM_STMCHN FMA(FM_STMCHN) +#define FMA_FM_RPR FMA(FM_RPR) +#define FMA_FM_WPXA0 FMA(FM_WPXA0) +#define FMA_FM_WPXA2 FMA(FM_WPXA2) +#define FMA_FM_MARR FMA(FM_MARR) +#define FMA_FM_MARW FMA(FM_MARW) +#define FMA_FM_MDRU FMA(FM_MDRU) +#define FMA_FM_MDRL FMA(FM_MDRL) +#define FMA_ST1L FMA(FM_ST1L) +#define FMA_ST1U FMA(FM_ST1U) +#define FMA_ST2L FMA(FM_ST2L) +#define FMA_ST2U FMA(FM_ST2U) +#ifdef SUPERNET_3 +#define FMA_ST3L FMA(FM_ST3L) +#define FMA_ST3U FMA(FM_ST3U) +#endif + +#define TMODE_RRQ RQ_RRQ +#define TMODE_WAQ2 RQ_WA2 +#define HSRA HSR(0) + + +#define FMA_FM_ST1L FMA_ST1L +#define FMA_FM_ST1U FMA_ST1U +#define FMA_FM_ST2L FMA_ST2L +#define FMA_FM_ST2U FMA_ST2U +#ifdef SUPERNET_3 +#define FMA_FM_ST3L FMA_ST3L +#define FMA_FM_ST3U FMA_ST3U +#endif + +#define FMA_FM_SWPR FMA(FM_SWPR) + +#define FMA_FM_RPXA0 FMA(FM_RPXA0) + +#define FMA_FM_RPXS FMA(FM_RPXS) +#define FMA_FM_WPXS FMA(FM_WPXS) + +#define FMA_FM_IMSK1U FMA(FM_IMSK1U) +#define FMA_FM_IMSK1L FMA(FM_IMSK1L) + +#define FMA_FM_EAS FMA(FM_EAS) +#define FMA_FM_EAA0 FMA(FM_EAA0) + +#define TMODE_WAQ0 RQ_WA0 +#define TMODE_WSQ RQ_WSQ + +/* Define default for DRV_PCM_STATE_CHANGE */ +#ifndef DRV_PCM_STATE_CHANGE +#define DRV_PCM_STATE_CHANGE(smc,plc,p_state) /* nothing */ +#endif + +/* Define default for DRV_RMT_INDICATION */ +#ifndef DRV_RMT_INDICATION +#define DRV_RMT_INDICATION(smc,i) /* nothing */ +#endif + +#endif /* n_SKFBIINC_ */ + diff --git a/kernel/drivers/net/fddi/skfp/h/smc.h b/kernel/drivers/net/fddi/skfp/h/smc.h new file mode 100644 index 000000000..bd1166bf8 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/smc.h @@ -0,0 +1,488 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _SCMECM_ +#define _SCMECM_ + +#if defined(PCI) && !defined(OSDEF) +/* + * In the case of the PCI bus the file osdef1st.h must be present + */ +#define OSDEF +#endif + +#ifdef PCI +#ifndef SUPERNET_3 +#define SUPERNET_3 +#endif +#ifndef TAG_MODE +#define TAG_MODE +#endif +#endif + +/* + * include all other files in required order + * the following files must have been included before: + * types.h + * fddi.h + */ +#ifdef OSDEF +#include "osdef1st.h" +#endif /* OSDEF */ +#ifdef OEM_CONCEPT +#include "oemdef.h" +#endif /* OEM_CONCEPT */ +#include "smt.h" +#include "cmtdef.h" +#include "fddimib.h" +#include "targethw.h" /* all target hw dependencies */ +#include "targetos.h" /* all target os dependencies */ +#ifdef ESS +#include "sba.h" +#endif + +/* + * Event Queue + * queue.c + * events are class/value pairs + * class is addressee, e.g. RMT, PCM etc. + * value is command, e.g. line state change, ring op change etc. + */ +struct event_queue { + u_short class ; /* event class */ + u_short event ; /* event value */ +} ; + +/* + * define event queue as circular buffer + */ +#ifdef CONCENTRATOR +#define MAX_EVENT 128 +#else /* nCONCENTRATOR */ +#define MAX_EVENT 64 +#endif /* nCONCENTRATOR */ + +struct s_queue { + + struct event_queue ev_queue[MAX_EVENT]; + struct event_queue *ev_put ; + struct event_queue *ev_get ; +} ; + +/* + * ECM - Entity Coordination Management + * ecm.c + */ +struct s_ecm { + u_char path_test ; /* ECM path test variable */ + u_char sb_flag ; /* ECM stuck bypass */ + u_char DisconnectFlag ; /* jd 05-Aug-1999 Bug #10419 + * ECM disconnected */ + u_char ecm_line_state ; /* flag to dispatcher : line states */ + u_long trace_prop ; /* ECM Trace_Prop flag >= 16 bits !! */ + /* NUMPHYS note: + * this variable must have enough bits to hold all entiies in + * the station. So NUMPHYS may not be greater than 31. + */ + char ec_pad[2] ; + struct smt_timer ecm_timer ; /* timer */ +} ; + + +/* + * RMT - Ring Management + * rmt.c + */ +struct s_rmt { + u_char dup_addr_test ; /* state of dupl. addr. test */ + u_char da_flag ; /* flag : duplicate address det. */ + u_char loop_avail ; /* flag : MAC available for loopback */ + u_char sm_ma_avail ; /* flag : MAC available for SMT */ + u_char no_flag ; /* flag : ring not operational */ + u_char bn_flag ; /* flag : MAC reached beacon state */ + u_char jm_flag ; /* flag : jamming in NON_OP_DUP */ + u_char rm_join ; /* CFM flag RM_Join */ + u_char rm_loop ; /* CFM flag RM_Loop */ + + long fast_rm_join ; /* bit mask of active ports */ + /* + * timer and flags + */ + struct smt_timer rmt_timer0 ; /* timer 0 */ + struct smt_timer rmt_timer1 ; /* timer 1 */ + struct smt_timer rmt_timer2 ; /* timer 2 */ + u_char timer0_exp ; /* flag : timer 0 expired */ + u_char timer1_exp ; /* flag : timer 1 expired */ + u_char timer2_exp ; /* flag : timer 2 expired */ + + u_char rm_pad1[1] ; +} ; + +/* + * CFM - Configuration Management + * cfm.c + * used for SAS and DAS + */ +struct s_cfm { + u_char cf_state; /* CFM state machine current state */ + u_char cf_pad[3] ; +} ; + +/* + * CEM - Configuration Element Management + * cem.c + * used for Concentrator + */ +#ifdef CONCENTRATOR +struct s_cem { + int ce_state ; /* CEM state */ + int ce_port ; /* PA PB PM PM+1 .. */ + int ce_type ; /* TA TB TS TM */ +} ; + +/* + * linked list of CCEs in current token path + */ +struct s_c_ring { + struct s_c_ring *c_next ; + char c_entity ; +} ; + +struct mib_path_config { + u_long fddimibPATHConfigSMTIndex; + u_long fddimibPATHConfigPATHIndex; + u_long fddimibPATHConfigTokenOrder; + u_long fddimibPATHConfigResourceType; +#define SNMP_RES_TYPE_MAC 2 /* Resource is a MAC */ +#define SNMP_RES_TYPE_PORT 4 /* Resource is a PORT */ + u_long fddimibPATHConfigResourceIndex; + u_long fddimibPATHConfigCurrentPath; +#define SNMP_PATH_ISOLATED 1 /* Current path is isolated */ +#define SNMP_PATH_LOCAL 2 /* Current path is local */ +#define SNMP_PATH_SECONDARY 3 /* Current path is secondary */ +#define SNMP_PATH_PRIMARY 4 /* Current path is primary */ +#define SNMP_PATH_CONCATENATED 5 /* Current path is concatenated */ +#define SNMP_PATH_THRU 6 /* Current path is thru */ +}; + + +#endif + +/* + * PCM connect states + */ +#define PCM_DISABLED 0 +#define PCM_CONNECTING 1 +#define PCM_STANDBY 2 +#define PCM_ACTIVE 3 + +struct s_pcm { + u_char pcm_pad[3] ; +} ; + +/* + * PHY struct + * one per physical port + */ +struct s_phy { + /* Inter Module Globals */ + struct fddi_mib_p *mib ; + + u_char np ; /* index 0 .. NUMPHYS */ + u_char cf_join ; + u_char cf_loop ; + u_char wc_flag ; /* withhold connection flag */ + u_char pc_mode ; /* Holds the negotiated mode of the PCM */ + u_char pc_lem_fail ; /* flag : LCT failed */ + u_char lc_test ; + u_char scrub ; /* CFM flag Scrub -> PCM */ + char phy_name ; + u_char pmd_type[2] ; /* SK connector/transceiver type codes */ +#define PMD_SK_CONN 0 /* pmd_type[PMD_SK_CONN] = Connector */ +#define PMD_SK_PMD 1 /* pmd_type[PMD_SK_PMD] = Xver */ + u_char pmd_scramble ; /* scrambler on/off */ + + /* inner Module Globals */ + u_char curr_ls ; /* current line state */ + u_char ls_flag ; + u_char rc_flag ; + u_char tc_flag ; + u_char td_flag ; + u_char bitn ; + u_char tr_flag ; /* trace recvd while in active */ + u_char twisted ; /* flag to indicate an A-A or B-B connection */ + u_char t_val[NUMBITS] ; /* transmit bits for signaling */ + u_char r_val[NUMBITS] ; /* receive bits for signaling */ + u_long t_next[NUMBITS] ; + struct smt_timer pcm_timer0 ; + struct smt_timer pcm_timer1 ; + struct smt_timer pcm_timer2 ; + u_char timer0_exp ; + u_char timer1_exp ; + u_char timer2_exp ; + u_char pcm_pad1[1] ; + int cem_pst ; /* CEM privae state; used for dual homing */ + struct lem_counter lem ; +#ifdef AMDPLC + struct s_plc plc ; +#endif +} ; + +/* + * timer package + * smttimer.c + */ +struct s_timer { + struct smt_timer *st_queue ; + struct smt_timer st_fast ; +} ; + +/* + * SRF types and data + */ +#define SMT_EVENT_BASE 1 +#define SMT_EVENT_MAC_PATH_CHANGE (SMT_EVENT_BASE+0) +#define SMT_EVENT_MAC_NEIGHBOR_CHANGE (SMT_EVENT_BASE+1) +#define SMT_EVENT_PORT_PATH_CHANGE (SMT_EVENT_BASE+2) +#define SMT_EVENT_PORT_CONNECTION (SMT_EVENT_BASE+3) + +#define SMT_IS_CONDITION(x) ((x)>=SMT_COND_BASE) + +#define SMT_COND_BASE (SMT_EVENT_PORT_CONNECTION+1) +#define SMT_COND_SMT_PEER_WRAP (SMT_COND_BASE+0) +#define SMT_COND_SMT_HOLD (SMT_COND_BASE+1) +#define SMT_COND_MAC_FRAME_ERROR (SMT_COND_BASE+2) +#define SMT_COND_MAC_DUP_ADDR (SMT_COND_BASE+3) +#define SMT_COND_MAC_NOT_COPIED (SMT_COND_BASE+4) +#define SMT_COND_PORT_EB_ERROR (SMT_COND_BASE+5) +#define SMT_COND_PORT_LER (SMT_COND_BASE+6) + +#define SR0_WAIT 0 +#define SR1_HOLDOFF 1 +#define SR2_DISABLED 2 + +struct s_srf { + u_long SRThreshold ; /* threshold value */ + u_char RT_Flag ; /* report transmitted flag */ + u_char sr_state ; /* state-machine */ + u_char any_report ; /* any report required */ + u_long TSR ; /* timer */ + u_short ring_status ; /* IBM ring status */ +} ; + +/* + * IBM token ring status + */ +#define RS_RES15 (1<<15) /* reserved */ +#define RS_HARDERROR (1<<14) /* ring down */ +#define RS_SOFTERROR (1<<13) /* sent SRF */ +#define RS_BEACON (1<<12) /* transmitted beacon */ +#define RS_PATHTEST (1<<11) /* path test failed */ +#define RS_SELFTEST (1<<10) /* selftest required */ +#define RS_RES9 (1<< 9) /* reserved */ +#define RS_DISCONNECT (1<< 8) /* remote disconnect */ +#define RS_RES7 (1<< 7) /* reserved */ +#define RS_DUPADDR (1<< 6) /* duplicate address */ +#define RS_NORINGOP (1<< 5) /* no ring op */ +#define RS_VERSION (1<< 4) /* SMT version mismatch */ +#define RS_STUCKBYPASSS (1<< 3) /* stuck bypass */ +#define RS_EVENT (1<< 2) /* FDDI event occurred */ +#define RS_RINGOPCHANGE (1<< 1) /* ring op changed */ +#define RS_RES0 (1<< 0) /* reserved */ + +#define RS_SET(smc,bit) \ + ring_status_indication(smc,smc->srf.ring_status |= bit) +#define RS_CLEAR(smc,bit) \ + ring_status_indication(smc,smc->srf.ring_status &= ~bit) + +#define RS_CLEAR_EVENT (0xffff & ~(RS_NORINGOP)) + +/* Define the AIX-event-Notification as null function if it isn't defined */ +/* in the targetos.h file */ +#ifndef AIX_EVENT +#define AIX_EVENT(smc,opt0,opt1,opt2,opt3) /* nothing */ +#endif + +struct s_srf_evc { + u_char evc_code ; /* event code type */ + u_char evc_index ; /* index for mult. instances */ + u_char evc_rep_required ; /* report required */ + u_short evc_para ; /* SMT Para Number */ + u_char *evc_cond_state ; /* condition state */ + u_char *evc_multiple ; /* multiple occurrence */ +} ; + +/* + * Values used by frame based services + * smt.c + */ +#define SMT_MAX_TEST 5 +#define SMT_TID_NIF 0 /* pending NIF request */ +#define SMT_TID_NIF_TEST 1 /* pending NIF test */ +#define SMT_TID_ECF_UNA 2 /* pending ECF UNA test */ +#define SMT_TID_ECF_DNA 3 /* pending ECF DNA test */ +#define SMT_TID_ECF 4 /* pending ECF test */ + +struct smt_values { + u_long smt_tvu ; /* timer valid una */ + u_long smt_tvd ; /* timer valid dna */ + u_long smt_tid ; /* transaction id */ + u_long pend[SMT_MAX_TEST] ; /* TID of requests */ + u_long uniq_time ; /* unique time stamp */ + u_short uniq_ticks ; /* unique time stamp */ + u_short please_reconnect ; /* flag : reconnect */ + u_long smt_last_lem ; + u_long smt_last_notify ; + struct smt_timer smt_timer ; /* SMT NIF timer */ + u_long last_tok_time[NUMMACS]; /* token cnt emulation */ +} ; + +/* + * SMT/CMT configurable parameters + */ +#define SMT_DAS 0 /* dual attach */ +#define SMT_SAS 1 /* single attach */ +#define SMT_NAC 2 /* null attach concentrator */ + +struct smt_config { + u_char attach_s ; /* CFM attach to secondary path */ + u_char sas ; /* SMT_DAS/SAS/NAC */ + u_char build_ring_map ; /* build ringmap if TRUE */ + u_char numphys ; /* number of active phys */ + u_char sc_pad[1] ; + + u_long pcm_tb_min ; /* PCM : TB_Min timer value */ + u_long pcm_tb_max ; /* PCM : TB_Max timer value */ + u_long pcm_c_min ; /* PCM : C_Min timer value */ + u_long pcm_t_out ; /* PCM : T_Out timer value */ + u_long pcm_tl_min ; /* PCM : TL_min timer value */ + u_long pcm_lc_short ; /* PCM : LC_Short timer value */ + u_long pcm_lc_medium ; /* PCM : LC_Medium timer value */ + u_long pcm_lc_long ; /* PCM : LC_Long timer value */ + u_long pcm_lc_extended ; /* PCM : LC_Extended timer value */ + u_long pcm_t_next_9 ; /* PCM : T_Next[9] timer value */ + u_long pcm_ns_max ; /* PCM : NS_Max timer value */ + + u_long ecm_i_max ; /* ECM : I_Max timer value */ + u_long ecm_in_max ; /* ECM : IN_Max timer value */ + u_long ecm_td_min ; /* ECM : TD_Min timer */ + u_long ecm_test_done ; /* ECM : path test done timer */ + u_long ecm_check_poll ; /* ECM : check bypass poller */ + + u_long rmt_t_non_op ; /* RMT : T_Non_OP timer value */ + u_long rmt_t_stuck ; /* RMT : T_Stuck timer value */ + u_long rmt_t_direct ; /* RMT : T_Direct timer value */ + u_long rmt_t_jam ; /* RMT : T_Jam timer value */ + u_long rmt_t_announce ; /* RMT : T_Announce timer value */ + u_long rmt_t_poll ; /* RMT : claim/beacon poller */ + u_long rmt_dup_mac_behavior ; /* Flag for the beavior of SMT if + * a Duplicate MAC Address was detected. + * FALSE: SMT will leave finally the ring + * TRUE: SMT will reinstert into the ring + */ + u_long mac_d_max ; /* MAC : D_Max timer value */ + + u_long lct_short ; /* LCT : error threshold */ + u_long lct_medium ; /* LCT : error threshold */ + u_long lct_long ; /* LCT : error threshold */ + u_long lct_extended ; /* LCT : error threshold */ +} ; + +#ifdef DEBUG +/* + * Debugging struct sometimes used in smc + */ +struct smt_debug { + int d_smtf ; + int d_smt ; + int d_ecm ; + int d_rmt ; + int d_cfm ; + int d_pcm ; + int d_plc ; +#ifdef ESS + int d_ess ; +#endif +#ifdef SBA + int d_sba ; +#endif + struct os_debug d_os; /* Include specific OS DEBUG struct */ +} ; + +#ifndef DEBUG_BRD +/* all boards shall be debugged with one debug struct */ +extern struct smt_debug debug; /* Declaration of debug struct */ +#endif /* DEBUG_BRD */ + +#endif /* DEBUG */ + +/* + * the SMT Context Struct SMC + * this struct contains ALL global variables of SMT + */ +struct s_smc { + struct s_smt_os os ; /* os specific */ + struct s_smt_hw hw ; /* hardware */ + +/* + * NOTE: os and hw MUST BE the first two structs + * anything beyond hw WILL BE SET TO ZERO in smt_set_defaults() + */ + struct smt_config s ; /* smt constants */ + struct smt_values sm ; /* smt variables */ + struct s_ecm e ; /* ecm */ + struct s_rmt r ; /* rmt */ + struct s_cfm cf ; /* cfm/cem */ +#ifdef CONCENTRATOR + struct s_cem ce[NUMPHYS] ; /* cem */ + struct s_c_ring cr[NUMPHYS+NUMMACS] ; +#endif + struct s_pcm p ; /* pcm */ + struct s_phy y[NUMPHYS] ; /* phy */ + struct s_queue q ; /* queue */ + struct s_timer t ; /* timer */ + struct s_srf srf ; /* SRF */ + struct s_srf_evc evcs[6+NUMPHYS*4] ; + struct fddi_mib mib ; /* __THE_MIB__ */ +#ifdef SBA + struct s_sba sba ; /* SBA variables */ +#endif +#ifdef ESS + struct s_ess ess ; /* Ess variables */ +#endif +#if defined(DEBUG) && defined(DEBUG_BRD) + /* If you want all single board to be debugged separately */ + struct smt_debug debug; /* Declaration of debug struct */ +#endif /* DEBUG_BRD && DEBUG */ +} ; + +extern const struct fddi_addr fddi_broadcast; + +void all_selection_criteria(struct s_smc *smc); +void card_stop(struct s_smc *smc); +void init_board(struct s_smc *smc, u_char *mac_addr); +int init_fplus(struct s_smc *smc); +void init_plc(struct s_smc *smc); +int init_smt(struct s_smc *smc, u_char *mac_addr); +void mac1_irq(struct s_smc *smc, u_short stu, u_short stl); +void mac2_irq(struct s_smc *smc, u_short code_s2u, u_short code_s2l); +void mac3_irq(struct s_smc *smc, u_short code_s3u, u_short code_s3l); +int pcm_status_twisted(struct s_smc *smc); +void plc1_irq(struct s_smc *smc); +void plc2_irq(struct s_smc *smc); +void read_address(struct s_smc *smc, u_char *mac_addr); +void timer_irq(struct s_smc *smc); + +#endif /* _SCMECM_ */ + diff --git a/kernel/drivers/net/fddi/skfp/h/smt.h b/kernel/drivers/net/fddi/skfp/h/smt.h new file mode 100644 index 000000000..2030f9cbb --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/smt.h @@ -0,0 +1,882 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * SMT 7.2 frame definitions + */ + +#ifndef _SMT_ +#define _SMT_ + +/* #define SMT5_10 */ +#define SMT6_10 +#define SMT7_20 + +#define OPT_PMF /* if parameter management is supported */ +#define OPT_SRF /* if status report is supported */ + +/* + * SMT frame version 5.1 + */ + +#define SMT_VID 0x0001 /* V 5.1 .. 6.1 */ +#define SMT_VID_2 0x0002 /* V 7.2 */ + +struct smt_sid { + u_char sid_oem[2] ; /* implementation spec. */ + struct fddi_addr sid_node ; /* node address */ +} ; + +typedef u_char t_station_id[8] ; + +/* + * note on alignment : + * sizeof(struct smt_header) = 32 + * all parameters are long aligned + * if struct smt_header starts at offset 0, all longs are aligned correctly + * (FC starts at offset 3) + */ +_packed struct smt_header { + struct fddi_addr smt_dest ; /* destination address */ + struct fddi_addr smt_source ; /* source address */ + u_char smt_class ; /* NIF, SIF ... */ + u_char smt_type ; /* req., response .. */ + u_short smt_version ; /* version id */ + u_int smt_tid ; /* transaction ID */ + struct smt_sid smt_sid ; /* station ID */ + u_short smt_pad ; /* pad with 0 */ + u_short smt_len ; /* length of info field */ +} ; +#define SWAP_SMTHEADER "662sl8ss" + +#if 0 +/* + * MAC FC values + */ +#define FC_SMT_INFO 0x41 /* SMT info */ +#define FC_SMT_NSA 0x4f /* SMT Next Station Addressing */ +#endif + + +/* + * type codes + */ +#define SMT_ANNOUNCE 0x01 /* announcement */ +#define SMT_REQUEST 0x02 /* request */ +#define SMT_REPLY 0x03 /* reply */ + +/* + * class codes + */ +#define SMT_NIF 0x01 /* neighbor information frames */ +#define SMT_SIF_CONFIG 0x02 /* station information configuration */ +#define SMT_SIF_OPER 0x03 /* station information operation */ +#define SMT_ECF 0x04 /* echo frames */ +#define SMT_RAF 0x05 /* resource allocation */ +#define SMT_RDF 0x06 /* request denied */ +#define SMT_SRF 0x07 /* status report */ +#define SMT_PMF_GET 0x08 /* parameter management get */ +#define SMT_PMF_SET 0x09 /* parameter management set */ +#define SMT_ESF 0xff /* extended service */ + +#define SMT_MAX_ECHO_LEN 4458 /* max length of SMT Echo */ +#if defined(CONC) || defined(CONC_II) +#define SMT_TEST_ECHO_LEN 50 /* test length of SMT Echo */ +#else +#define SMT_TEST_ECHO_LEN SMT_MAX_ECHO_LEN /* test length */ +#endif + +#define SMT_MAX_INFO_LEN (4352-20) /* max length for SMT info */ + + +/* + * parameter types + */ + +struct smt_para { + u_short p_type ; /* type */ + u_short p_len ; /* length of parameter */ +} ; + +#define PARA_LEN (sizeof(struct smt_para)) + +#define SMTSETPARA(p,t) (p)->para.p_type = (t),\ + (p)->para.p_len = sizeof(*(p)) - PARA_LEN + +/* + * P01 : Upstream Neighbor Address, UNA + */ +#define SMT_P_UNA 0x0001 /* upstream neighbor address */ +#define SWAP_SMT_P_UNA "s6" + +struct smt_p_una { + struct smt_para para ; /* generic parameter header */ + u_short una_pad ; + struct fddi_addr una_node ; /* node address, zero if unknown */ +} ; + +/* + * P02 : Station Descriptor + */ +#define SMT_P_SDE 0x0002 /* station descriptor */ +#define SWAP_SMT_P_SDE "1111" + +#define SMT_SDE_STATION 0 /* end node */ +#define SMT_SDE_CONCENTRATOR 1 /* concentrator */ + +struct smt_p_sde { + struct smt_para para ; /* generic parameter header */ + u_char sde_type ; /* station type */ + u_char sde_mac_count ; /* number of MACs */ + u_char sde_non_master ; /* number of A,B or S ports */ + u_char sde_master ; /* number of S ports on conc. */ +} ; + +/* + * P03 : Station State + */ +#define SMT_P_STATE 0x0003 /* station state */ +#define SWAP_SMT_P_STATE "scc" + +struct smt_p_state { + struct smt_para para ; /* generic parameter header */ + u_short st_pad ; + u_char st_topology ; /* topology */ + u_char st_dupl_addr ; /* duplicate address detected */ +} ; +#define SMT_ST_WRAPPED (1<<0) /* station wrapped */ +#define SMT_ST_UNATTACHED (1<<1) /* unattached concentrator */ +#define SMT_ST_TWISTED_A (1<<2) /* A-A connection, twisted ring */ +#define SMT_ST_TWISTED_B (1<<3) /* B-B connection, twisted ring */ +#define SMT_ST_ROOTED_S (1<<4) /* rooted station */ +#define SMT_ST_SRF (1<<5) /* SRF protocol supported */ +#define SMT_ST_SYNC_SERVICE (1<<6) /* use synchronous bandwidth */ + +#define SMT_ST_MY_DUPA (1<<0) /* my station detected dupl. */ +#define SMT_ST_UNA_DUPA (1<<1) /* my UNA detected duplicate */ + +/* + * P04 : timestamp + */ +#define SMT_P_TIMESTAMP 0x0004 /* time stamp */ +#define SWAP_SMT_P_TIMESTAMP "8" +struct smt_p_timestamp { + struct smt_para para ; /* generic parameter header */ + u_char ts_time[8] ; /* time, resolution 80nS, unique */ +} ; + +/* + * P05 : station policies + */ +#define SMT_P_POLICY 0x0005 /* station policies */ +#define SWAP_SMT_P_POLICY "ss" + +struct smt_p_policy { + struct smt_para para ; /* generic parameter header */ + u_short pl_config ; + u_short pl_connect ; /* bit string POLICY_AA ... */ +} ; +#define SMT_PL_HOLD 1 /* hold policy supported (Dual MAC) */ + +/* + * P06 : latency equivalent + */ +#define SMT_P_LATENCY 0x0006 /* latency */ +#define SWAP_SMT_P_LATENCY "ssss" + +/* + * note: latency has two phy entries by definition + * for a SAS, the 2nd one is null + */ +struct smt_p_latency { + struct smt_para para ; /* generic parameter header */ + u_short lt_phyout_idx1 ; /* index */ + u_short lt_latency1 ; /* latency , unit : byte clock */ + u_short lt_phyout_idx2 ; /* 0 if SAS */ + u_short lt_latency2 ; /* 0 if SAS */ +} ; + +/* + * P07 : MAC neighbors + */ +#define SMT_P_NEIGHBORS 0x0007 /* MAC neighbor description */ +#define SWAP_SMT_P_NEIGHBORS "ss66" + +struct smt_p_neighbor { + struct smt_para para ; /* generic parameter header */ + u_short nb_mib_index ; /* MIB index */ + u_short nb_mac_index ; /* n+1 .. n+m, m = #MACs, n = #PHYs */ + struct fddi_addr nb_una ; /* UNA , 0 for unknown */ + struct fddi_addr nb_dna ; /* DNA , 0 for unknown */ +} ; + +/* + * PHY record + */ +#define SMT_PHY_A 0 /* A port */ +#define SMT_PHY_B 1 /* B port */ +#define SMT_PHY_S 2 /* slave port */ +#define SMT_PHY_M 3 /* master port */ + +#define SMT_CS_DISABLED 0 /* connect state : disabled */ +#define SMT_CS_CONNECTING 1 /* connect state : connecting */ +#define SMT_CS_STANDBY 2 /* connect state : stand by */ +#define SMT_CS_ACTIVE 3 /* connect state : active */ + +#define SMT_RM_NONE 0 +#define SMT_RM_MAC 1 + +struct smt_phy_rec { + u_short phy_mib_index ; /* MIB index */ + u_char phy_type ; /* A/B/S/M */ + u_char phy_connect_state ; /* disabled/connecting/active */ + u_char phy_remote_type ; /* A/B/S/M */ + u_char phy_remote_mac ; /* none/remote */ + u_short phy_resource_idx ; /* 1 .. n */ +} ; + +/* + * MAC record + */ +struct smt_mac_rec { + struct fddi_addr mac_addr ; /* MAC address */ + u_short mac_resource_idx ; /* n+1 .. n+m */ +} ; + +/* + * P08 : path descriptors + * should be really an array ; however our environment has a fixed number of + * PHYs and MACs + */ +#define SMT_P_PATH 0x0008 /* path descriptor */ +#define SWAP_SMT_P_PATH "[6s]" + +struct smt_p_path { + struct smt_para para ; /* generic parameter header */ + struct smt_phy_rec pd_phy[2] ; /* PHY A */ + struct smt_mac_rec pd_mac ; /* MAC record */ +} ; + +/* + * P09 : MAC status + */ +#define SMT_P_MAC_STATUS 0x0009 /* MAC status */ +#define SWAP_SMT_P_MAC_STATUS "sslllllllll" + +struct smt_p_mac_status { + struct smt_para para ; /* generic parameter header */ + u_short st_mib_index ; /* MIB index */ + u_short st_mac_index ; /* n+1 .. n+m */ + u_int st_t_req ; /* T_Req */ + u_int st_t_neg ; /* T_Neg */ + u_int st_t_max ; /* T_Max */ + u_int st_tvx_value ; /* TVX_Value */ + u_int st_t_min ; /* T_Min */ + u_int st_sba ; /* synchr. bandwidth alloc */ + u_int st_frame_ct ; /* frame counter */ + u_int st_error_ct ; /* error counter */ + u_int st_lost_ct ; /* lost frames counter */ +} ; + +/* + * P0A : PHY link error rate monitoring + */ +#define SMT_P_LEM 0x000a /* link error monitor */ +#define SWAP_SMT_P_LEM "ssccccll" +/* + * units of lem_cutoff,lem_alarm,lem_estimate : 10**-x + */ +struct smt_p_lem { + struct smt_para para ; /* generic parameter header */ + u_short lem_mib_index ; /* MIB index */ + u_short lem_phy_index ; /* 1 .. n */ + u_char lem_pad2 ; /* be nice and make it even . */ + u_char lem_cutoff ; /* 0x4 .. 0xf, default 0x7 */ + u_char lem_alarm ; /* 0x4 .. 0xf, default 0x8 */ + u_char lem_estimate ; /* 0x0 .. 0xff */ + u_int lem_reject_ct ; /* 0x00000000 .. 0xffffffff */ + u_int lem_ct ; /* 0x00000000 .. 0xffffffff */ +} ; + +/* + * P0B : MAC frame counters + */ +#define SMT_P_MAC_COUNTER 0x000b /* MAC frame counters */ +#define SWAP_SMT_P_MAC_COUNTER "ssll" + +struct smt_p_mac_counter { + struct smt_para para ; /* generic parameter header */ + u_short mc_mib_index ; /* MIB index */ + u_short mc_index ; /* mac index */ + u_int mc_receive_ct ; /* receive counter */ + u_int mc_transmit_ct ; /* transmit counter */ +} ; + +/* + * P0C : MAC frame not copied counter + */ +#define SMT_P_MAC_FNC 0x000c /* MAC frame not copied counter */ +#define SWAP_SMT_P_MAC_FNC "ssl" + +struct smt_p_mac_fnc { + struct smt_para para ; /* generic parameter header */ + u_short nc_mib_index ; /* MIB index */ + u_short nc_index ; /* mac index */ + u_int nc_counter ; /* not copied counter */ +} ; + + +/* + * P0D : MAC priority values + */ +#define SMT_P_PRIORITY 0x000d /* MAC priority values */ +#define SWAP_SMT_P_PRIORITY "ssl" + +struct smt_p_priority { + struct smt_para para ; /* generic parameter header */ + u_short pr_mib_index ; /* MIB index */ + u_short pr_index ; /* mac index */ + u_int pr_priority[7] ; /* priority values */ +} ; + +/* + * P0E : PHY elasticity buffer status + */ +#define SMT_P_EB 0x000e /* PHY EB status */ +#define SWAP_SMT_P_EB "ssl" + +struct smt_p_eb { + struct smt_para para ; /* generic parameter header */ + u_short eb_mib_index ; /* MIB index */ + u_short eb_index ; /* phy index */ + u_int eb_error_ct ; /* # of eb overflows */ +} ; + +/* + * P0F : manufacturer field + */ +#define SMT_P_MANUFACTURER 0x000f /* manufacturer field */ +#define SWAP_SMT_P_MANUFACTURER "" + +struct smp_p_manufacturer { + struct smt_para para ; /* generic parameter header */ + u_char mf_data[32] ; /* OUI + arbitrary data */ +} ; + +/* + * P10 : user field + */ +#define SMT_P_USER 0x0010 /* manufacturer field */ +#define SWAP_SMT_P_USER "" + +struct smp_p_user { + struct smt_para para ; /* generic parameter header */ + u_char us_data[32] ; /* arbitrary data */ +} ; + + + +/* + * P11 : echo data + */ +#define SMT_P_ECHODATA 0x0011 /* echo data */ +#define SWAP_SMT_P_ECHODATA "" + +struct smt_p_echo { + struct smt_para para ; /* generic parameter header */ + u_char ec_data[SMT_MAX_ECHO_LEN-4] ; /* echo data */ +} ; + +/* + * P12 : reason code + */ +#define SMT_P_REASON 0x0012 /* reason code */ +#define SWAP_SMT_P_REASON "l" + +struct smt_p_reason { + struct smt_para para ; /* generic parameter header */ + u_int rdf_reason ; /* CLASS/VERSION */ +} ; +#define SMT_RDF_CLASS 0x00000001 /* class not supported */ +#define SMT_RDF_VERSION 0x00000002 /* version not supported */ +#define SMT_RDF_SUCCESS 0x00000003 /* success (PMF) */ +#define SMT_RDF_BADSET 0x00000004 /* bad set count (PMF) */ +#define SMT_RDF_ILLEGAL 0x00000005 /* read only (PMF) */ +#define SMT_RDF_NOPARAM 0x6 /* parameter not supported (PMF) */ +#define SMT_RDF_RANGE 0x8 /* out of range */ +#define SMT_RDF_AUTHOR 0x9 /* not autohorized */ +#define SMT_RDF_LENGTH 0x0a /* length error */ +#define SMT_RDF_TOOLONG 0x0b /* length error */ +#define SMT_RDF_SBA 0x0d /* SBA denied */ + +/* + * P13 : refused frame beginning + */ +#define SMT_P_REFUSED 0x0013 /* refused frame beginning */ +#define SWAP_SMT_P_REFUSED "l" + +struct smt_p_refused { + struct smt_para para ; /* generic parameter header */ + u_int ref_fc ; /* 3 bytes 0 + FC */ + struct smt_header ref_header ; /* refused header */ +} ; + +/* + * P14 : supported SMT versions + */ +#define SMT_P_VERSION 0x0014 /* SMT supported versions */ +#define SWAP_SMT_P_VERSION "sccss" + +struct smt_p_version { + struct smt_para para ; /* generic parameter header */ + u_short v_pad ; + u_char v_n ; /* 1 .. 0xff, #versions */ + u_char v_index ; /* 1 .. 0xff, index of op. v. */ + u_short v_version[1] ; /* list of min. 1 version */ + u_short v_pad2 ; /* pad if necessary */ +} ; + +/* + * P15 : Resource Type + */ +#define SWAP_SMT_P0015 "l" + +struct smt_p_0015 { + struct smt_para para ; /* generic parameter header */ + u_int res_type ; /* recsource type */ +} ; + +#define SYNC_BW 0x00000001L /* Synchronous Bandwidth */ + +/* + * P16 : SBA Command + */ +#define SWAP_SMT_P0016 "l" + +struct smt_p_0016 { + struct smt_para para ; /* generic parameter header */ + u_int sba_cmd ; /* command for the SBA */ +} ; + +#define REQUEST_ALLOCATION 0x1 /* req allocation of sync bandwidth */ +#define REPORT_ALLOCATION 0x2 /* rep of sync bandwidth allocation */ +#define CHANGE_ALLOCATION 0x3 /* forces a station using sync band-*/ + /* width to change its current allo-*/ + /* cation */ + +/* + * P17 : SBA Payload Request + */ +#define SWAP_SMT_P0017 "l" + +struct smt_p_0017 { + struct smt_para para ; /* generic parameter header */ + int sba_pl_req ; /* total sync bandwidth measured in */ +} ; /* bytes per 125 us */ + +/* + * P18 : SBA Overhead Request + */ +#define SWAP_SMT_P0018 "l" + +struct smt_p_0018 { + struct smt_para para ; /* generic parameter header */ + int sba_ov_req ; /* total sync bandwidth req for overhead*/ +} ; /* measuered in bytes per T_Neg */ + +/* + * P19 : SBA Allocation Address + */ +#define SWAP_SMT_P0019 "s6" + +struct smt_p_0019 { + struct smt_para para ; /* generic parameter header */ + u_short sba_pad ; + struct fddi_addr alloc_addr ; /* Allocation Address */ +} ; + +/* + * P1A : SBA Category + */ +#define SWAP_SMT_P001A "l" + +struct smt_p_001a { + struct smt_para para ; /* generic parameter header */ + u_int category ; /* Allocator defined classification */ +} ; + +/* + * P1B : Maximum T_Neg + */ +#define SWAP_SMT_P001B "l" + +struct smt_p_001b { + struct smt_para para ; /* generic parameter header */ + u_int max_t_neg ; /* longest T_NEG for the sync service*/ +} ; + +/* + * P1C : Minimum SBA Segment Size + */ +#define SWAP_SMT_P001C "l" + +struct smt_p_001c { + struct smt_para para ; /* generic parameter header */ + u_int min_seg_siz ; /* smallest number of bytes per frame*/ +} ; + +/* + * P1D : SBA Allocatable + */ +#define SWAP_SMT_P001D "l" + +struct smt_p_001d { + struct smt_para para ; /* generic parameter header */ + u_int allocatable ; /* total sync bw available for alloc */ +} ; + +/* + * P20 0B : frame status capabilities + * NOTE: not in swap table, is used by smt.c AND PMF table + */ +#define SMT_P_FSC 0x200b +/* #define SWAP_SMT_P_FSC "ssss" */ + +struct smt_p_fsc { + struct smt_para para ; /* generic parameter header */ + u_short fsc_pad0 ; + u_short fsc_mac_index ; /* mac index 1 .. ff */ + u_short fsc_pad1 ; + u_short fsc_value ; /* FSC_TYPE[0-2] */ +} ; + +#define FSC_TYPE0 0 /* "normal" node (A/C handling) */ +#define FSC_TYPE1 1 /* Special A/C indicator forwarding */ +#define FSC_TYPE2 2 /* Special A/C indicator forwarding */ + +/* + * P00 21 : user defined authoriziation (see pmf.c) + */ +#define SMT_P_AUTHOR 0x0021 + +/* + * notification parameters + */ +#define SWAP_SMT_P1048 "ll" +struct smt_p_1048 { + u_int p1048_flag ; + u_int p1048_cf_state ; +} ; + +/* + * NOTE: all 2xxx 3xxx and 4xxx must include the INDEX in the swap string, + * even so the INDEX is NOT part of the struct. + * INDEX is already swapped in pmf.c, format in string is '4' + */ +#define SWAP_SMT_P208C "4lss66" +struct smt_p_208c { + u_int p208c_flag ; + u_short p208c_pad ; + u_short p208c_dupcondition ; + struct fddi_addr p208c_fddilong ; + struct fddi_addr p208c_fddiunalong ; +} ; + +#define SWAP_SMT_P208D "4lllll" +struct smt_p_208d { + u_int p208d_flag ; + u_int p208d_frame_ct ; + u_int p208d_error_ct ; + u_int p208d_lost_ct ; + u_int p208d_ratio ; +} ; + +#define SWAP_SMT_P208E "4llll" +struct smt_p_208e { + u_int p208e_flag ; + u_int p208e_not_copied ; + u_int p208e_copied ; + u_int p208e_not_copied_ratio ; +} ; + +#define SWAP_SMT_P208F "4ll6666s6" + +struct smt_p_208f { + u_int p208f_multiple ; + u_int p208f_nacondition ; + struct fddi_addr p208f_old_una ; + struct fddi_addr p208f_new_una ; + struct fddi_addr p208f_old_dna ; + struct fddi_addr p208f_new_dna ; + u_short p208f_curren_path ; + struct fddi_addr p208f_smt_address ; +} ; + +#define SWAP_SMT_P2090 "4lssl" + +struct smt_p_2090 { + u_int p2090_multiple ; + u_short p2090_availablepaths ; + u_short p2090_currentpath ; + u_int p2090_requestedpaths ; +} ; + +/* + * NOTE: + * special kludge for parameters 320b,320f,3210 + * these parameters are part of RAF frames + * RAF frames are parsed in SBA.C and must be swapped + * PMF.C has special code to avoid double swapping + */ +#ifdef LITTLE_ENDIAN +#define SBAPATHINDEX (0x01000000L) +#else +#define SBAPATHINDEX (0x01L) +#endif + +#define SWAP_SMT_P320B "42s" + +struct smt_p_320b { + struct smt_para para ; /* generic parameter header */ + u_int mib_index ; + u_short path_pad ; + u_short path_index ; +} ; + +#define SWAP_SMT_P320F "4l" + +struct smt_p_320f { + struct smt_para para ; /* generic parameter header */ + u_int mib_index ; + u_int mib_payload ; +} ; + +#define SWAP_SMT_P3210 "4l" + +struct smt_p_3210 { + struct smt_para para ; /* generic parameter header */ + u_int mib_index ; + u_int mib_overhead ; +} ; + +#define SWAP_SMT_P4050 "4l1111ll" + +struct smt_p_4050 { + u_int p4050_flag ; + u_char p4050_pad ; + u_char p4050_cutoff ; + u_char p4050_alarm ; + u_char p4050_estimate ; + u_int p4050_reject_ct ; + u_int p4050_ct ; +} ; + +#define SWAP_SMT_P4051 "4lssss" +struct smt_p_4051 { + u_int p4051_multiple ; + u_short p4051_porttype ; + u_short p4051_connectstate ; + u_short p4051_pc_neighbor ; + u_short p4051_pc_withhold ; +} ; + +#define SWAP_SMT_P4052 "4ll" +struct smt_p_4052 { + u_int p4052_flag ; + u_int p4052_eberrorcount ; +} ; + +#define SWAP_SMT_P4053 "4lsslss" + +struct smt_p_4053 { + u_int p4053_multiple ; + u_short p4053_availablepaths ; + u_short p4053_currentpath ; + u_int p4053_requestedpaths ; + u_short p4053_mytype ; + u_short p4053_neighbortype ; +} ; + + +#define SMT_P_SETCOUNT 0x1035 +#define SWAP_SMT_P_SETCOUNT "l8" + +struct smt_p_setcount { + struct smt_para para ; /* generic parameter header */ + u_int count ; + u_char timestamp[8] ; +} ; + +/* + * SMT FRAMES + */ + +/* + * NIF : neighbor information frames + */ +struct smt_nif { + struct smt_header smt ; /* generic header */ + struct smt_p_una una ; /* UNA */ + struct smt_p_sde sde ; /* station descriptor */ + struct smt_p_state state ; /* station state */ +#ifdef SMT6_10 + struct smt_p_fsc fsc ; /* frame status cap. */ +#endif +} ; + +/* + * SIF : station information frames + */ +struct smt_sif_config { + struct smt_header smt ; /* generic header */ + struct smt_p_timestamp ts ; /* time stamp */ + struct smt_p_sde sde ; /* station descriptor */ + struct smt_p_version version ; /* supported versions */ + struct smt_p_state state ; /* station state */ + struct smt_p_policy policy ; /* station policy */ + struct smt_p_latency latency ; /* path latency */ + struct smt_p_neighbor neighbor ; /* neighbors, we have only one*/ +#ifdef OPT_PMF + struct smt_p_setcount setcount ; /* Set Count mandatory */ +#endif + /* WARNING : path MUST BE LAST FIELD !!! (see smt.c:smt_fill_path) */ + struct smt_p_path path ; /* path descriptor */ +} ; +#define SIZEOF_SMT_SIF_CONFIG (sizeof(struct smt_sif_config)- \ + sizeof(struct smt_p_path)) + +struct smt_sif_operation { + struct smt_header smt ; /* generic header */ + struct smt_p_timestamp ts ; /* time stamp */ + struct smt_p_mac_status status ; /* mac status */ + struct smt_p_mac_counter mc ; /* MAC counter */ + struct smt_p_mac_fnc fnc ; /* MAC frame not copied */ + struct smp_p_manufacturer man ; /* manufacturer field */ + struct smp_p_user user ; /* user field */ +#ifdef OPT_PMF + struct smt_p_setcount setcount ; /* Set Count mandatory */ +#endif + /* must be last */ + struct smt_p_lem lem[1] ; /* phy lem status */ +} ; +#define SIZEOF_SMT_SIF_OPERATION (sizeof(struct smt_sif_operation)- \ + sizeof(struct smt_p_lem)) + +/* + * ECF : echo frame + */ +struct smt_ecf { + struct smt_header smt ; /* generic header */ + struct smt_p_echo ec_echo ; /* echo parameter */ +} ; +#define SMT_ECF_LEN (sizeof(struct smt_header)+sizeof(struct smt_para)) + +/* + * RDF : request denied frame + */ +struct smt_rdf { + struct smt_header smt ; /* generic header */ + struct smt_p_reason reason ; /* reason code */ + struct smt_p_version version ; /* supported versions */ + struct smt_p_refused refused ; /* refused frame fragment */ +} ; + +/* + * SBA Request Allocation Response Frame + */ +struct smt_sba_alc_res { + struct smt_header smt ; /* generic header */ + struct smt_p_0015 s_type ; /* resource type */ + struct smt_p_0016 cmd ; /* SBA command */ + struct smt_p_reason reason ; /* reason code */ + struct smt_p_320b path ; /* path type */ + struct smt_p_320f payload ; /* current SBA payload */ + struct smt_p_3210 overhead ; /* current SBA overhead */ + struct smt_p_0019 a_addr ; /* Allocation Address */ + struct smt_p_001a cat ; /* Category - from the request */ + struct smt_p_001d alloc ; /* SBA Allocatable */ +} ; + +/* + * SBA Request Allocation Request Frame + */ +struct smt_sba_alc_req { + struct smt_header smt ; /* generic header */ + struct smt_p_0015 s_type ; /* resource type */ + struct smt_p_0016 cmd ; /* SBA command */ + struct smt_p_320b path ; /* path type */ + struct smt_p_0017 pl_req ; /* requested payload */ + struct smt_p_0018 ov_req ; /* requested SBA overhead */ + struct smt_p_320f payload ; /* current SBA payload */ + struct smt_p_3210 overhead ; /* current SBA overhead */ + struct smt_p_0019 a_addr ; /* Allocation Address */ + struct smt_p_001a cat ; /* Category - from the request */ + struct smt_p_001b tneg ; /* max T-NEG */ + struct smt_p_001c segm ; /* minimum segment size */ +} ; + +/* + * SBA Change Allocation Request Frame + */ +struct smt_sba_chg { + struct smt_header smt ; /* generic header */ + struct smt_p_0015 s_type ; /* resource type */ + struct smt_p_0016 cmd ; /* SBA command */ + struct smt_p_320b path ; /* path type */ + struct smt_p_320f payload ; /* current SBA payload */ + struct smt_p_3210 overhead ; /* current SBA overhead */ + struct smt_p_001a cat ; /* Category - from the request */ +} ; + +/* + * SBA Report Allocation Request Frame + */ +struct smt_sba_rep_req { + struct smt_header smt ; /* generic header */ + struct smt_p_0015 s_type ; /* resource type */ + struct smt_p_0016 cmd ; /* SBA command */ +} ; + +/* + * SBA Report Allocation Response Frame + */ +struct smt_sba_rep_res { + struct smt_header smt ; /* generic header */ + struct smt_p_0015 s_type ; /* resource type */ + struct smt_p_0016 cmd ; /* SBA command */ + struct smt_p_320b path ; /* path type */ + struct smt_p_320f payload ; /* current SBA payload */ + struct smt_p_3210 overhead ; /* current SBA overhead */ +} ; + +/* + * actions + */ +#define SMT_STATION_ACTION 1 +#define SMT_STATION_ACTION_CONNECT 0 +#define SMT_STATION_ACTION_DISCONNECT 1 +#define SMT_STATION_ACTION_PATHTEST 2 +#define SMT_STATION_ACTION_SELFTEST 3 +#define SMT_STATION_ACTION_DISABLE_A 4 +#define SMT_STATION_ACTION_DISABLE_B 5 +#define SMT_STATION_ACTION_DISABLE_M 6 + +#define SMT_PORT_ACTION 2 +#define SMT_PORT_ACTION_MAINT 0 +#define SMT_PORT_ACTION_ENABLE 1 +#define SMT_PORT_ACTION_DISABLE 2 +#define SMT_PORT_ACTION_START 3 +#define SMT_PORT_ACTION_STOP 4 + +#endif /* _SMT_ */ diff --git a/kernel/drivers/net/fddi/skfp/h/smt_p.h b/kernel/drivers/net/fddi/skfp/h/smt_p.h new file mode 100644 index 000000000..99f9be955 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/smt_p.h @@ -0,0 +1,326 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * defines for all SMT attributes + */ + +/* + * this boring file was produced by perl + * thanks Larry ! + */ +#define SMT_P0012 0x0012 + +#define SMT_P0015 0x0015 +#define SMT_P0016 0x0016 +#define SMT_P0017 0x0017 +#define SMT_P0018 0x0018 +#define SMT_P0019 0x0019 + +#define SMT_P001A 0x001a +#define SMT_P001B 0x001b +#define SMT_P001C 0x001c +#define SMT_P001D 0x001d + +#define SMT_P100A 0x100a +#define SMT_P100B 0x100b +#define SMT_P100C 0x100c +#define SMT_P100D 0x100d +#define SMT_P100E 0x100e +#define SMT_P100F 0x100f +#define SMT_P1010 0x1010 +#define SMT_P1011 0x1011 +#define SMT_P1012 0x1012 +#define SMT_P1013 0x1013 +#define SMT_P1014 0x1014 +#define SMT_P1015 0x1015 +#define SMT_P1016 0x1016 +#define SMT_P1017 0x1017 +#define SMT_P1018 0x1018 +#define SMT_P1019 0x1019 +#define SMT_P101A 0x101a +#define SMT_P101B 0x101b +#define SMT_P101C 0x101c +#define SMT_P101D 0x101d +#define SMT_P101E 0x101e +#define SMT_P101F 0x101f +#define SMT_P1020 0x1020 +#define SMT_P1021 0x1021 +#define SMT_P1022 0x1022 +#define SMT_P1023 0x1023 +#define SMT_P1024 0x1024 +#define SMT_P1025 0x1025 +#define SMT_P1026 0x1026 +#define SMT_P1027 0x1027 +#define SMT_P1028 0x1028 +#define SMT_P1029 0x1029 +#define SMT_P102A 0x102a +#define SMT_P102B 0x102b +#define SMT_P102C 0x102c +#define SMT_P102D 0x102d +#define SMT_P102E 0x102e +#define SMT_P102F 0x102f +#define SMT_P1030 0x1030 +#define SMT_P1031 0x1031 +#define SMT_P1032 0x1032 +#define SMT_P1033 0x1033 +#define SMT_P1034 0x1034 +#define SMT_P1035 0x1035 +#define SMT_P1036 0x1036 +#define SMT_P1037 0x1037 +#define SMT_P1038 0x1038 +#define SMT_P1039 0x1039 +#define SMT_P103A 0x103a +#define SMT_P103B 0x103b +#define SMT_P103C 0x103c +#define SMT_P103D 0x103d +#define SMT_P103E 0x103e +#define SMT_P103F 0x103f +#define SMT_P1040 0x1040 +#define SMT_P1041 0x1041 +#define SMT_P1042 0x1042 +#define SMT_P1043 0x1043 +#define SMT_P1044 0x1044 +#define SMT_P1045 0x1045 +#define SMT_P1046 0x1046 +#define SMT_P1047 0x1047 +#define SMT_P1048 0x1048 +#define SMT_P1049 0x1049 +#define SMT_P104A 0x104a +#define SMT_P104B 0x104b +#define SMT_P104C 0x104c +#define SMT_P104D 0x104d +#define SMT_P104E 0x104e +#define SMT_P104F 0x104f +#define SMT_P1050 0x1050 +#define SMT_P1051 0x1051 +#define SMT_P1052 0x1052 +#define SMT_P1053 0x1053 +#define SMT_P1054 0x1054 + +#define SMT_P10F0 0x10f0 +#define SMT_P10F1 0x10f1 +#ifdef ESS +#define SMT_P10F2 0x10f2 +#define SMT_P10F3 0x10f3 +#define SMT_P10F4 0x10f4 +#define SMT_P10F5 0x10f5 +#define SMT_P10F6 0x10f6 +#define SMT_P10F7 0x10f7 +#endif +#ifdef SBA +#define SMT_P10F8 0x10f8 +#define SMT_P10F9 0x10f9 +#endif + +#define SMT_P200A 0x200a +#define SMT_P200B 0x200b +#define SMT_P200C 0x200c +#define SMT_P200D 0x200d +#define SMT_P200E 0x200e +#define SMT_P200F 0x200f +#define SMT_P2010 0x2010 +#define SMT_P2011 0x2011 +#define SMT_P2012 0x2012 +#define SMT_P2013 0x2013 +#define SMT_P2014 0x2014 +#define SMT_P2015 0x2015 +#define SMT_P2016 0x2016 +#define SMT_P2017 0x2017 +#define SMT_P2018 0x2018 +#define SMT_P2019 0x2019 +#define SMT_P201A 0x201a +#define SMT_P201B 0x201b +#define SMT_P201C 0x201c +#define SMT_P201D 0x201d +#define SMT_P201E 0x201e +#define SMT_P201F 0x201f +#define SMT_P2020 0x2020 +#define SMT_P2021 0x2021 +#define SMT_P2022 0x2022 +#define SMT_P2023 0x2023 +#define SMT_P2024 0x2024 +#define SMT_P2025 0x2025 +#define SMT_P2026 0x2026 +#define SMT_P2027 0x2027 +#define SMT_P2028 0x2028 +#define SMT_P2029 0x2029 +#define SMT_P202A 0x202a +#define SMT_P202B 0x202b +#define SMT_P202C 0x202c +#define SMT_P202D 0x202d +#define SMT_P202E 0x202e +#define SMT_P202F 0x202f +#define SMT_P2030 0x2030 +#define SMT_P2031 0x2031 +#define SMT_P2032 0x2032 +#define SMT_P2033 0x2033 +#define SMT_P2034 0x2034 +#define SMT_P2035 0x2035 +#define SMT_P2036 0x2036 +#define SMT_P2037 0x2037 +#define SMT_P2038 0x2038 +#define SMT_P2039 0x2039 +#define SMT_P203A 0x203a +#define SMT_P203B 0x203b +#define SMT_P203C 0x203c +#define SMT_P203D 0x203d +#define SMT_P203E 0x203e +#define SMT_P203F 0x203f +#define SMT_P2040 0x2040 +#define SMT_P2041 0x2041 +#define SMT_P2042 0x2042 +#define SMT_P2043 0x2043 +#define SMT_P2044 0x2044 +#define SMT_P2045 0x2045 +#define SMT_P2046 0x2046 +#define SMT_P2047 0x2047 +#define SMT_P2048 0x2048 +#define SMT_P2049 0x2049 +#define SMT_P204A 0x204a +#define SMT_P204B 0x204b +#define SMT_P204C 0x204c +#define SMT_P204D 0x204d +#define SMT_P204E 0x204e +#define SMT_P204F 0x204f +#define SMT_P2050 0x2050 +#define SMT_P2051 0x2051 +#define SMT_P2052 0x2052 +#define SMT_P2053 0x2053 +#define SMT_P2054 0x2054 +#define SMT_P2055 0x2055 +#define SMT_P2056 0x2056 +#define SMT_P2057 0x2057 +#define SMT_P2058 0x2058 +#define SMT_P2059 0x2059 +#define SMT_P205A 0x205a +#define SMT_P205B 0x205b +#define SMT_P205C 0x205c +#define SMT_P205D 0x205d +#define SMT_P205E 0x205e +#define SMT_P205F 0x205f +#define SMT_P2060 0x2060 +#define SMT_P2061 0x2061 +#define SMT_P2062 0x2062 +#define SMT_P2063 0x2063 +#define SMT_P2064 0x2064 +#define SMT_P2065 0x2065 +#define SMT_P2066 0x2066 +#define SMT_P2067 0x2067 +#define SMT_P2068 0x2068 +#define SMT_P2069 0x2069 +#define SMT_P206A 0x206a +#define SMT_P206B 0x206b +#define SMT_P206C 0x206c +#define SMT_P206D 0x206d +#define SMT_P206E 0x206e +#define SMT_P206F 0x206f +#define SMT_P2070 0x2070 +#define SMT_P2071 0x2071 +#define SMT_P2072 0x2072 +#define SMT_P2073 0x2073 +#define SMT_P2074 0x2074 +#define SMT_P2075 0x2075 +#define SMT_P2076 0x2076 + +#define SMT_P208C 0x208c +#define SMT_P208D 0x208d +#define SMT_P208E 0x208e +#define SMT_P208F 0x208f +#define SMT_P2090 0x2090 + +#define SMT_P20F0 0x20F0 +#define SMT_P20F1 0x20F1 + +#define SMT_P320A 0x320a +#define SMT_P320B 0x320b +#define SMT_P320C 0x320c +#define SMT_P320D 0x320d +#define SMT_P320E 0x320e +#define SMT_P320F 0x320f +#define SMT_P3210 0x3210 +#define SMT_P3211 0x3211 +#define SMT_P3212 0x3212 +#define SMT_P3213 0x3213 +#define SMT_P3214 0x3214 +#define SMT_P3215 0x3215 +#define SMT_P3216 0x3216 +#define SMT_P3217 0x3217 + +#define SMT_P400A 0x400a +#define SMT_P400B 0x400b +#define SMT_P400C 0x400c +#define SMT_P400D 0x400d +#define SMT_P400E 0x400e +#define SMT_P400F 0x400f +#define SMT_P4010 0x4010 +#define SMT_P4011 0x4011 +#define SMT_P4012 0x4012 +#define SMT_P4013 0x4013 +#define SMT_P4014 0x4014 +#define SMT_P4015 0x4015 +#define SMT_P4016 0x4016 +#define SMT_P4017 0x4017 +#define SMT_P4018 0x4018 +#define SMT_P4019 0x4019 +#define SMT_P401A 0x401a +#define SMT_P401B 0x401b +#define SMT_P401C 0x401c +#define SMT_P401D 0x401d +#define SMT_P401E 0x401e +#define SMT_P401F 0x401f +#define SMT_P4020 0x4020 +#define SMT_P4021 0x4021 +#define SMT_P4022 0x4022 +#define SMT_P4023 0x4023 +#define SMT_P4024 0x4024 +#define SMT_P4025 0x4025 +#define SMT_P4026 0x4026 +#define SMT_P4027 0x4027 +#define SMT_P4028 0x4028 +#define SMT_P4029 0x4029 +#define SMT_P402A 0x402a +#define SMT_P402B 0x402b +#define SMT_P402C 0x402c +#define SMT_P402D 0x402d +#define SMT_P402E 0x402e +#define SMT_P402F 0x402f +#define SMT_P4030 0x4030 +#define SMT_P4031 0x4031 +#define SMT_P4032 0x4032 +#define SMT_P4033 0x4033 +#define SMT_P4034 0x4034 +#define SMT_P4035 0x4035 +#define SMT_P4036 0x4036 +#define SMT_P4037 0x4037 +#define SMT_P4038 0x4038 +#define SMT_P4039 0x4039 +#define SMT_P403A 0x403a +#define SMT_P403B 0x403b +#define SMT_P403C 0x403c +#define SMT_P403D 0x403d +#define SMT_P403E 0x403e +#define SMT_P403F 0x403f +#define SMT_P4040 0x4040 +#define SMT_P4041 0x4041 +#define SMT_P4042 0x4042 +#define SMT_P4043 0x4043 +#define SMT_P4044 0x4044 +#define SMT_P4045 0x4045 +#define SMT_P4046 0x4046 + +#define SMT_P4050 0x4050 +#define SMT_P4051 0x4051 +#define SMT_P4052 0x4052 +#define SMT_P4053 0x4053 diff --git a/kernel/drivers/net/fddi/skfp/h/smtstate.h b/kernel/drivers/net/fddi/skfp/h/smtstate.h new file mode 100644 index 000000000..62fe69507 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/smtstate.h @@ -0,0 +1,106 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _SKFP_H_SMTSTATE_H_ +#define _SKFP_H_SMTSTATE_H_ + +/* + * SMT state definitions + */ + +#ifndef KERNEL +/* + * PCM states + */ +#define PC0_OFF 0 +#define PC1_BREAK 1 +#define PC2_TRACE 2 +#define PC3_CONNECT 3 +#define PC4_NEXT 4 +#define PC5_SIGNAL 5 +#define PC6_JOIN 6 +#define PC7_VERIFY 7 +#define PC8_ACTIVE 8 +#define PC9_MAINT 9 + +/* + * PCM modes + */ +#define PM_NONE 0 +#define PM_PEER 1 +#define PM_TREE 2 + +/* + * PCM type + */ +#define TA 0 +#define TB 1 +#define TS 2 +#define TM 3 +#define TNONE 4 + +/* + * CFM states + */ +#define SC0_ISOLATED 0 /* isolated */ +#define SC1_WRAP_A 5 /* wrap A */ +#define SC2_WRAP_B 6 /* wrap B */ +#define SC4_THRU_A 12 /* through A */ +#define SC5_THRU_B 7 /* through B (SMt 6.2) */ +#define SC7_WRAP_S 8 /* SAS */ + +/* + * ECM states + */ +#define EC0_OUT 0 +#define EC1_IN 1 +#define EC2_TRACE 2 +#define EC3_LEAVE 3 +#define EC4_PATH_TEST 4 +#define EC5_INSERT 5 +#define EC6_CHECK 6 +#define EC7_DEINSERT 7 + +/* + * RMT states + */ +#define RM0_ISOLATED 0 +#define RM1_NON_OP 1 /* not operational */ +#define RM2_RING_OP 2 /* ring operational */ +#define RM3_DETECT 3 /* detect dupl addresses */ +#define RM4_NON_OP_DUP 4 /* dupl. addr detected */ +#define RM5_RING_OP_DUP 5 /* ring oper. with dupl. addr */ +#define RM6_DIRECTED 6 /* sending directed beacons */ +#define RM7_TRACE 7 /* trace initiated */ +#endif + +struct pcm_state { + unsigned char pcm_type ; /* TA TB TS TM */ + unsigned char pcm_state ; /* state PC[0-9]_* */ + unsigned char pcm_mode ; /* PM_{NONE,PEER,TREE} */ + unsigned char pcm_neighbor ; /* TA TB TS TM */ + unsigned char pcm_bsf ; /* flag bs : TRUE/FALSE */ + unsigned char pcm_lsf ; /* flag ls : TRUE/FALSE */ + unsigned char pcm_lct_fail ; /* counter lct_fail */ + unsigned char pcm_ls_rx ; /* rx line state */ + short pcm_r_val ; /* signaling bits */ + short pcm_t_val ; /* signaling bits */ +} ; + +struct smt_state { + struct pcm_state pcm_state[NUMPHYS] ; /* port A & port B */ +} ; + +#endif + diff --git a/kernel/drivers/net/fddi/skfp/h/supern_2.h b/kernel/drivers/net/fddi/skfp/h/supern_2.h new file mode 100644 index 000000000..4ee360d2d --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/supern_2.h @@ -0,0 +1,1059 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + defines for AMD Supernet II chip set + the chips are referred to as + FPLUS Formac Plus + PLC Physical Layer + + added defines for AMD Supernet III chip set + added comments on differences between Supernet II and Supernet III + added defines for the Motorola ELM (MOT_ELM) +*/ + +#ifndef _SUPERNET_ +#define _SUPERNET_ + +/* + * Define Supernet 3 when used + */ +#ifdef PCI +#ifndef SUPERNET_3 +#define SUPERNET_3 +#endif +#define TAG +#endif + +#define MB 0xff +#define MW 0xffff +#define MD 0xffffffff + +/* + * FORMAC frame status (rx_msext) + */ +#define FS_EI (1<<2) +#define FS_AI (1<<1) +#define FS_CI (1<<0) + +#define FS_MSVALID (1<<15) /* end of queue */ +#define FS_MSRABT (1<<14) /* frame was aborted during reception*/ +#define FS_SSRCRTG (1<<12) /* if SA has set MSB (source-routing)*/ +#define FS_SEAC2 (FS_EI<<9) /* error indicator */ +#define FS_SEAC1 (FS_AI<<9) /* address indicator */ +#define FS_SEAC0 (FS_CI<<9) /* copy indicator */ +#define FS_SFRMERR (1<<8) /* error detected (CRC or length) */ +#define FS_SADRRG (1<<7) /* address recognized */ +#define FS_SFRMTY2 (1<<6) /* frame-class bit */ +#define FS_SFRMTY1 (1<<5) /* frame-type bit (impementor) */ +#define FS_SFRMTY0 (1<<4) /* frame-type bit (LLC) */ +#define FS_ERFBB1 (1<<1) /* byte offset (depends on LSB bit) */ +#define FS_ERFBB0 (1<<0) /* - " - */ + +/* + * status frame type + */ +#define FRM_SMT (0) /* asynchr. frames */ +#define FRM_LLCA (1) +#define FRM_IMPA (2) +#define FRM_MAC (4) /* synchr. frames */ +#define FRM_LLCS (5) +#define FRM_IMPS (6) + +/* + * bits in rx_descr.i (receive frame status word) + */ +#define RX_MSVALID ((long)1<<31) /* memory status valid */ +#define RX_MSRABT ((long)1<<30) /* memory status receive abort */ +#define RX_FS_E ((long)FS_SEAC2<<16) /* error indicator */ +#define RX_FS_A ((long)FS_SEAC1<<16) /* address indicator */ +#define RX_FS_C ((long)FS_SEAC0<<16) /* copy indicator */ +#define RX_FS_CRC ((long)FS_SFRMERR<<16)/* error detected */ +#define RX_FS_ADDRESS ((long)FS_SADRRG<<16) /* address recognized */ +#define RX_FS_MAC ((long)FS_SFRMTY2<<16)/* MAC frame */ +#define RX_FS_SMT ((long)0<<16) /* SMT frame */ +#define RX_FS_IMPL ((long)FS_SFRMTY1<<16)/* implementer frame */ +#define RX_FS_LLC ((long)FS_SFRMTY0<<16)/* LLC frame */ + +/* + * receive frame descriptor + */ +union rx_descr { + struct { +#ifdef LITTLE_ENDIAN + unsigned int rx_length :16 ; /* frame length lower/upper byte */ + unsigned int rx_erfbb :2 ; /* received frame byte boundary */ + unsigned int rx_reserv2:2 ; /* reserved */ + unsigned int rx_sfrmty :3 ; /* frame type bits */ + unsigned int rx_sadrrg :1 ; /* DA == MA or broad-/multicast */ + unsigned int rx_sfrmerr:1 ; /* received frame not valid */ + unsigned int rx_seac0 :1 ; /* frame-copied C-indicator */ + unsigned int rx_seac1 :1 ; /* address-match A-indicator */ + unsigned int rx_seac2 :1 ; /* frame-error E-indicator */ + unsigned int rx_ssrcrtg:1 ; /* == 1 SA has MSB set */ + unsigned int rx_reserv1:1 ; /* reserved */ + unsigned int rx_msrabt :1 ; /* memory status receive abort */ + unsigned int rx_msvalid:1 ; /* memory status valid */ +#else + unsigned int rx_msvalid:1 ; /* memory status valid */ + unsigned int rx_msrabt :1 ; /* memory status receive abort */ + unsigned int rx_reserv1:1 ; /* reserved */ + unsigned int rx_ssrcrtg:1 ; /* == 1 SA has MSB set */ + unsigned int rx_seac2 :1 ; /* frame-error E-indicator */ + unsigned int rx_seac1 :1 ; /* address-match A-indicator */ + unsigned int rx_seac0 :1 ; /* frame-copied C-indicator */ + unsigned int rx_sfrmerr:1 ; /* received frame not valid */ + unsigned int rx_sadrrg :1 ; /* DA == MA or broad-/multicast */ + unsigned int rx_sfrmty :3 ; /* frame type bits */ + unsigned int rx_erfbb :2 ; /* received frame byte boundary */ + unsigned int rx_reserv2:2 ; /* reserved */ + unsigned int rx_length :16 ; /* frame length lower/upper byte */ +#endif + } r ; + long i ; +} ; + +/* defines for Receive Frame Descriptor access */ +#define RD_S_ERFBB 0x00030000L /* received frame byte boundary */ +#define RD_S_RES2 0x000c0000L /* reserved */ +#define RD_S_SFRMTY 0x00700000L /* frame type bits */ +#define RD_S_SADRRG 0x00800000L /* DA == MA or broad-/multicast */ +#define RD_S_SFRMERR 0x01000000L /* received frame not valid */ +#define RD_S_SEAC 0x0e000000L /* frame status indicators */ +#define RD_S_SEAC0 0x02000000L /* frame-copied case-indicator */ +#define RD_S_SEAC1 0x04000000L /* address-match A-indicator */ +#define RD_S_SEAC2 0x08000000L /* frame-error E-indicator */ +#define RD_S_SSRCRTG 0x10000000L /* == 1 SA has MSB set */ +#define RD_S_RES1 0x20000000L /* reserved */ +#define RD_S_MSRABT 0x40000000L /* memory status receive abort */ +#define RD_S_MSVALID 0x80000000L /* memory status valid */ + +#define RD_STATUS 0xffff0000L +#define RD_LENGTH 0x0000ffffL + +/* defines for Receive Frames Status Word values */ +/*RD_S_SFRMTY*/ +#define RD_FRM_SMT (unsigned long)(0<<20) /* asynchr. frames */ +#define RD_FRM_LLCA (unsigned long)(1<<20) +#define RD_FRM_IMPA (unsigned long)(2<<20) +#define RD_FRM_MAC (unsigned long)(4<<20) /* synchr. frames */ +#define RD_FRM_LLCS (unsigned long)(5<<20) +#define RD_FRM_IMPS (unsigned long)(6<<20) + +#define TX_DESCRIPTOR 0x40000000L +#define TX_OFFSET_3 0x18000000L + +#define TXP1 2 + +/* + * transmit frame descriptor + */ +union tx_descr { + struct { +#ifdef LITTLE_ENDIAN + unsigned int tx_length:16 ; /* frame length lower/upper byte */ + unsigned int tx_res :8 ; /* reserved (bit 16..23) */ + unsigned int tx_xmtabt:1 ; /* transmit abort */ + unsigned int tx_nfcs :1 ; /* no frame check sequence */ + unsigned int tx_xdone :1 ; /* give up token */ + unsigned int tx_rpxm :2 ; /* byte offset */ + unsigned int tx_pat1 :2 ; /* must be TXP1 */ + unsigned int tx_more :1 ; /* more frame in chain */ +#else + unsigned int tx_more :1 ; /* more frame in chain */ + unsigned int tx_pat1 :2 ; /* must be TXP1 */ + unsigned int tx_rpxm :2 ; /* byte offset */ + unsigned int tx_xdone :1 ; /* give up token */ + unsigned int tx_nfcs :1 ; /* no frame check sequence */ + unsigned int tx_xmtabt:1 ; /* transmit abort */ + unsigned int tx_res :8 ; /* reserved (bit 16..23) */ + unsigned int tx_length:16 ; /* frame length lower/upper byte */ +#endif + } t ; + long i ; +} ; + +/* defines for Transmit Descriptor access */ +#define TD_C_MORE 0x80000000L /* more frame in chain */ +#define TD_C_DESCR 0x60000000L /* must be TXP1 */ +#define TD_C_TXFBB 0x18000000L /* byte offset */ +#define TD_C_XDONE 0x04000000L /* give up token */ +#define TD_C_NFCS 0x02000000L /* no frame check sequence */ +#define TD_C_XMTABT 0x01000000L /* transmit abort */ + +#define TD_C_LNCNU 0x0000ff00L +#define TD_C_LNCNL 0x000000ffL +#define TD_C_LNCN 0x0000ffffL /* frame length lower/upper byte */ + +/* + * transmit pointer + */ +union tx_pointer { + struct t { +#ifdef LITTLE_ENDIAN + unsigned int tp_pointer:16 ; /* pointer to tx_descr (low/high) */ + unsigned int tp_res :8 ; /* reserved (bit 16..23) */ + unsigned int tp_pattern:8 ; /* fixed pattern (bit 24..31) */ +#else + unsigned int tp_pattern:8 ; /* fixed pattern (bit 24..31) */ + unsigned int tp_res :8 ; /* reserved (bit 16..23) */ + unsigned int tp_pointer:16 ; /* pointer to tx_descr (low/high) */ +#endif + } t ; + long i ; +} ; + +/* defines for Nontag Mode Pointer access */ +#define TD_P_CNTRL 0xff000000L +#define TD_P_RPXU 0x0000ff00L +#define TD_P_RPXL 0x000000ffL +#define TD_P_RPX 0x0000ffffL + + +#define TX_PATTERN 0xa0 +#define TX_POINTER_END 0xa0000000L +#define TX_INT_PATTERN 0xa0000000L + +struct tx_queue { + struct tx_queue *tq_next ; + u_short tq_pack_offset ; /* offset buffer memory */ + u_char tq_pad[2] ; +} ; + +/* + defines for FORMAC Plus (Am79C830) +*/ + +/* + * FORMAC+ read/write (r/w) registers + */ +#define FM_CMDREG1 0x00 /* write command reg 1 instruction */ +#define FM_CMDREG2 0x01 /* write command reg 2 instruction */ +#define FM_ST1U 0x00 /* read upper 16-bit of status reg 1 */ +#define FM_ST1L 0x01 /* read lower 16-bit of status reg 1 */ +#define FM_ST2U 0x02 /* read upper 16-bit of status reg 2 */ +#define FM_ST2L 0x03 /* read lower 16-bit of status reg 2 */ +#define FM_IMSK1U 0x04 /* r/w upper 16-bit of IMSK 1 */ +#define FM_IMSK1L 0x05 /* r/w lower 16-bit of IMSK 1 */ +#define FM_IMSK2U 0x06 /* r/w upper 16-bit of IMSK 2 */ +#define FM_IMSK2L 0x07 /* r/w lower 16-bit of IMSK 2 */ +#define FM_SAID 0x08 /* r/w short addr.-individual */ +#define FM_LAIM 0x09 /* r/w long addr.-ind. (MSW of LAID) */ +#define FM_LAIC 0x0a /* r/w long addr.-ind. (middle)*/ +#define FM_LAIL 0x0b /* r/w long addr.-ind. (LSW) */ +#define FM_SAGP 0x0c /* r/w short address-group */ +#define FM_LAGM 0x0d /* r/w long addr.-gr. (MSW of LAGP) */ +#define FM_LAGC 0x0e /* r/w long addr.-gr. (middle) */ +#define FM_LAGL 0x0f /* r/w long addr.-gr. (LSW) */ +#define FM_MDREG1 0x10 /* r/w 16-bit mode reg 1 */ +#define FM_STMCHN 0x11 /* read state-machine reg */ +#define FM_MIR1 0x12 /* read upper 16-bit of MAC Info Reg */ +#define FM_MIR0 0x13 /* read lower 16-bit of MAC Info Reg */ +#define FM_TMAX 0x14 /* r/w 16-bit TMAX reg */ +#define FM_TVX 0x15 /* write 8-bit TVX reg with NP7-0 + read TVX on NP7-0, timer on NP15-8*/ +#define FM_TRT 0x16 /* r/w upper 16-bit of TRT timer */ +#define FM_THT 0x17 /* r/w upper 16-bit of THT timer */ +#define FM_TNEG 0x18 /* read upper 16-bit of TNEG (TTRT) */ +#define FM_TMRS 0x19 /* read lower 5-bit of TNEG,TRT,THT */ + /* F E D C B A 9 8 7 6 5 4 3 2 1 0 + x |-TNEG4-0| |-TRT4-0-| |-THT4-0-| (x-late count) */ +#define FM_TREQ0 0x1a /* r/w 16-bit TREQ0 reg (LSW of TRT) */ +#define FM_TREQ1 0x1b /* r/w 16-bit TREQ1 reg (MSW of TRT) */ +#define FM_PRI0 0x1c /* r/w priority r. for asyn.-queue 0 */ +#define FM_PRI1 0x1d /* r/w priority r. for asyn.-queue 1 */ +#define FM_PRI2 0x1e /* r/w priority r. for asyn.-queue 2 */ +#define FM_TSYNC 0x1f /* r/w 16-bit of the TSYNC register */ +#define FM_MDREG2 0x20 /* r/w 16-bit mode reg 2 */ +#define FM_FRMTHR 0x21 /* r/w the frame threshold register */ +#define FM_EACB 0x22 /* r/w end addr of claim/beacon area */ +#define FM_EARV 0x23 /* r/w end addr of receive queue */ +/* Supernet 3 */ +#define FM_EARV1 FM_EARV + +#define FM_EAS 0x24 /* r/w end addr of synchr. queue */ +#define FM_EAA0 0x25 /* r/w end addr of asyn. queue 0 */ +#define FM_EAA1 0x26 /* r/w end addr of asyn. queue 1 */ +#define FM_EAA2 0x27 /* r/w end addr of asyn. queue 2 */ +#define FM_SACL 0x28 /* r/w start addr of claim frame */ +#define FM_SABC 0x29 /* r/w start addr of beacon frame */ +#define FM_WPXSF 0x2a /* r/w the write ptr. for special fr.*/ +#define FM_RPXSF 0x2b /* r/w the read ptr. for special fr. */ +#define FM_RPR 0x2d /* r/w the read ptr. for receive qu. */ +#define FM_WPR 0x2e /* r/w the write ptr. for receive qu.*/ +#define FM_SWPR 0x2f /* r/w the shadow wr.-ptr. for rec.q.*/ +/* Supernet 3 */ +#define FM_RPR1 FM_RPR +#define FM_WPR1 FM_WPR +#define FM_SWPR1 FM_SWPR + +#define FM_WPXS 0x30 /* r/w the write ptr. for synchr. qu.*/ +#define FM_WPXA0 0x31 /* r/w the write ptr. for asyn. qu.0 */ +#define FM_WPXA1 0x32 /* r/w the write ptr. for asyn. qu.1 */ +#define FM_WPXA2 0x33 /* r/w the write ptr. for asyn. qu.2 */ +#define FM_SWPXS 0x34 /* r/w the shadow wr.-ptr. for syn.q.*/ +#define FM_SWPXA0 0x35 /* r/w the shad. wr.-ptr. for asyn.q0*/ +#define FM_SWPXA1 0x36 /* r/w the shad. wr.-ptr. for asyn.q1*/ +#define FM_SWPXA2 0x37 /* r/w the shad. wr.-ptr. for asyn.q2*/ +#define FM_RPXS 0x38 /* r/w the read ptr. for synchr. qu. */ +#define FM_RPXA0 0x39 /* r/w the read ptr. for asyn. qu. 0 */ +#define FM_RPXA1 0x3a /* r/w the read ptr. for asyn. qu. 1 */ +#define FM_RPXA2 0x3b /* r/w the read ptr. for asyn. qu. 2 */ +#define FM_MARR 0x3c /* r/w the memory read addr register */ +#define FM_MARW 0x3d /* r/w the memory write addr register*/ +#define FM_MDRU 0x3e /* r/w upper 16-bit of mem. data reg */ +#define FM_MDRL 0x3f /* r/w lower 16-bit of mem. data reg */ + +/* following instructions relate to MAC counters and timer */ +#define FM_TMSYNC 0x40 /* r/w upper 16 bits of TMSYNC timer */ +#define FM_FCNTR 0x41 /* r/w the 16-bit frame counter */ +#define FM_LCNTR 0x42 /* r/w the 16-bit lost counter */ +#define FM_ECNTR 0x43 /* r/w the 16-bit error counter */ + +/* Supernet 3: extensions to old register block */ +#define FM_FSCNTR 0x44 /* r/? Frame Strip Counter */ +#define FM_FRSELREG 0x45 /* r/w Frame Selection Register */ + +/* Supernet 3: extensions for 2. receive queue etc. */ +#define FM_MDREG3 0x60 /* r/w Mode Register 3 */ +#define FM_ST3U 0x61 /* read upper 16-bit of status reg 3 */ +#define FM_ST3L 0x62 /* read lower 16-bit of status reg 3 */ +#define FM_IMSK3U 0x63 /* r/w upper 16-bit of IMSK reg 3 */ +#define FM_IMSK3L 0x64 /* r/w lower 16-bit of IMSK reg 3 */ +#define FM_IVR 0x65 /* read Interrupt Vector register */ +#define FM_IMR 0x66 /* r/w Interrupt mask register */ +/* 0x67 Hidden */ +#define FM_RPR2 0x68 /* r/w the read ptr. for rec. qu. 2 */ +#define FM_WPR2 0x69 /* r/w the write ptr. for rec. qu. 2 */ +#define FM_SWPR2 0x6a /* r/w the shadow wptr. for rec. q. 2 */ +#define FM_EARV2 0x6b /* r/w end addr of rec. qu. 2 */ +#define FM_UNLCKDLY 0x6c /* r/w Auto Unlock Delay register */ + /* Bit 15-8: RECV2 unlock threshold */ + /* Bit 7-0: RECV1 unlock threshold */ +/* 0x6f-0x73 Hidden */ +#define FM_LTDPA1 0x79 /* r/w Last Trans desc ptr for A1 qu. */ +/* 0x80-0x9a PLCS registers of built-in PLCS (Supernet 3 only) */ + +/* Supernet 3: Adderss Filter Registers */ +#define FM_AFCMD 0xb0 /* r/w Address Filter Command Reg */ +#define FM_AFSTAT 0xb2 /* r/w Address Filter Status Reg */ +#define FM_AFBIST 0xb4 /* r/w Address Filter BIST signature */ +#define FM_AFCOMP2 0xb6 /* r/w Address Filter Comparand 2 */ +#define FM_AFCOMP1 0xb8 /* r/w Address Filter Comparand 1 */ +#define FM_AFCOMP0 0xba /* r/w Address Filter Comparand 0 */ +#define FM_AFMASK2 0xbc /* r/w Address Filter Mask 2 */ +#define FM_AFMASK1 0xbe /* r/w Address Filter Mask 1 */ +#define FM_AFMASK0 0xc0 /* r/w Address Filter Mask 0 */ +#define FM_AFPERS 0xc2 /* r/w Address Filter Personality Reg */ + +/* Supernet 3: Orion (PDX?) Registers */ +#define FM_ORBIST 0xd0 /* r/w Orion BIST signature */ +#define FM_ORSTAT 0xd2 /* r/w Orion Status Register */ + + +/* + * Mode Register 1 (MDREG1) + */ +#define FM_RES0 0x0001 /* reserved */ + /* SN3: other definition */ +#define FM_XMTINH_HOLD 0x0002 /* transmit-inhibit/hold bit */ + /* SN3: other definition */ +#define FM_HOFLXI 0x0003 /* SN3: Hold / Flush / Inhibit */ +#define FM_FULL_HALF 0x0004 /* full-duplex/half-duplex bit */ +#define FM_LOCKTX 0x0008 /* lock-transmit-asynchr.-queues bit */ +#define FM_EXGPA0 0x0010 /* extended-group-addressing bit 0 */ +#define FM_EXGPA1 0x0020 /* extended-group-addressing bit 1 */ +#define FM_DISCRY 0x0040 /* disable-carry bit */ + /* SN3: reserved */ +#define FM_SELRA 0x0080 /* select input from PHY (1=RA,0=RB) */ + +#define FM_ADDET 0x0700 /* address detection */ +#define FM_MDAMA (0<<8) /* address detection : DA = MA */ +#define FM_MDASAMA (1<<8) /* address detection : DA=MA||SA=MA */ +#define FM_MRNNSAFNMA (2<<8) /* rec. non-NSA frames DA=MA&&SA!=MA */ +#define FM_MRNNSAF (3<<8) /* rec. non-NSA frames DA = MA */ +#define FM_MDISRCV (4<<8) /* disable receive function */ +#define FM_MRES0 (5<<8) /* reserve */ +#define FM_MLIMPROM (6<<8) /* limited-promiscuous mode */ +#define FM_MPROMISCOUS (7<<8) /* address detection : promiscuous */ + +#define FM_SELSA 0x0800 /* select-short-address bit */ + +#define FM_MMODE 0x7000 /* mode select */ +#define FM_MINIT (0<<12) /* initialize */ +#define FM_MMEMACT (1<<12) /* memory activate */ +#define FM_MONLINESP (2<<12) /* on-line special */ +#define FM_MONLINE (3<<12) /* on-line (FDDI operational mode) */ +#define FM_MILOOP (4<<12) /* internal loopback */ +#define FM_MRES1 (5<<12) /* reserved */ +#define FM_MRES2 (6<<12) /* reserved */ +#define FM_MELOOP (7<<12) /* external loopback */ + +#define FM_SNGLFRM 0x8000 /* single-frame-receive mode */ + /* SN3: reserved */ + +#define MDR1INIT (FM_MINIT | FM_MDAMA) + +/* + * Mode Register 2 (MDREG2) + */ +#define FM_AFULL 0x000f /* 4-bit value (empty loc.in txqueue)*/ +#define FM_RCVERR 0x0010 /* rec.-errored-frames bit */ +#define FM_SYMCTL 0x0020 /* sysmbol-control bit */ + /* SN3: reserved */ +#define FM_SYNPRQ 0x0040 /* synchron.-NP-DMA-request bit */ +#define FM_ENNPRQ 0x0080 /* enable-NP-DMA-request bit */ +#define FM_ENHSRQ 0x0100 /* enable-host-request bit */ +#define FM_RXFBB01 0x0600 /* rec. frame byte boundary bit0 & 1 */ +#define FM_LSB 0x0800 /* determ. ordering of bytes in buffer*/ +#define FM_PARITY 0x1000 /* 1 = even, 0 = odd */ +#define FM_CHKPAR 0x2000 /* 1 = parity of 32-bit buffer BD-bus*/ +#define FM_STRPFCS 0x4000 /* 1 = strips FCS field of rec.frame */ +#define FM_BMMODE 0x8000 /* Buffer-Memory-Mode (1 = tag mode) */ + /* SN3: 1 = tag, 0 = modified tag */ + +/* + * Status Register 1, Upper 16 Bits (ST1U) + */ +#define FM_STEFRMS 0x0001 /* transmit end of frame: synchr. qu.*/ +#define FM_STEFRMA0 0x0002 /* transmit end of frame: asyn. qu.0 */ +#define FM_STEFRMA1 0x0004 /* transmit end of frame: asyn. qu.1 */ +#define FM_STEFRMA2 0x0008 /* transmit end of frame: asyn. qu.2 */ + /* SN3: reserved */ +#define FM_STECFRMS 0x0010 /* transmit end of chain of syn. qu. */ + /* SN3: reserved */ +#define FM_STECFRMA0 0x0020 /* transmit end of chain of asyn. q0 */ + /* SN3: reserved */ +#define FM_STECFRMA1 0x0040 /* transmit end of chain of asyn. q1 */ + /* SN3: STECMDA1 */ +#define FM_STECMDA1 0x0040 /* SN3: 'no description' */ +#define FM_STECFRMA2 0x0080 /* transmit end of chain of asyn. q2 */ + /* SN3: reserved */ +#define FM_STEXDONS 0x0100 /* transmit until XDONE in syn. qu. */ +#define FM_STBFLA 0x0200 /* asynchr.-queue trans. buffer full */ +#define FM_STBFLS 0x0400 /* synchr.-queue transm. buffer full */ +#define FM_STXABRS 0x0800 /* synchr. queue transmit-abort */ +#define FM_STXABRA0 0x1000 /* asynchr. queue 0 transmit-abort */ +#define FM_STXABRA1 0x2000 /* asynchr. queue 1 transmit-abort */ +#define FM_STXABRA2 0x4000 /* asynchr. queue 2 transmit-abort */ + /* SN3: reserved */ +#define FM_SXMTABT 0x8000 /* transmit abort */ + +/* + * Status Register 1, Lower 16 Bits (ST1L) + */ +#define FM_SQLCKS 0x0001 /* queue lock for synchr. queue */ +#define FM_SQLCKA0 0x0002 /* queue lock for asynchr. queue 0 */ +#define FM_SQLCKA1 0x0004 /* queue lock for asynchr. queue 1 */ +#define FM_SQLCKA2 0x0008 /* queue lock for asynchr. queue 2 */ + /* SN3: reserved */ +#define FM_STXINFLS 0x0010 /* transmit instruction full: syn. */ + /* SN3: reserved */ +#define FM_STXINFLA0 0x0020 /* transmit instruction full: asyn.0 */ + /* SN3: reserved */ +#define FM_STXINFLA1 0x0040 /* transmit instruction full: asyn.1 */ + /* SN3: reserved */ +#define FM_STXINFLA2 0x0080 /* transmit instruction full: asyn.2 */ + /* SN3: reserved */ +#define FM_SPCEPDS 0x0100 /* parity/coding error: syn. queue */ +#define FM_SPCEPDA0 0x0200 /* parity/coding error: asyn. queue0 */ +#define FM_SPCEPDA1 0x0400 /* parity/coding error: asyn. queue1 */ +#define FM_SPCEPDA2 0x0800 /* parity/coding error: asyn. queue2 */ + /* SN3: reserved */ +#define FM_STBURS 0x1000 /* transmit buffer underrun: syn. q. */ +#define FM_STBURA0 0x2000 /* transmit buffer underrun: asyn.0 */ +#define FM_STBURA1 0x4000 /* transmit buffer underrun: asyn.1 */ +#define FM_STBURA2 0x8000 /* transmit buffer underrun: asyn.2 */ + /* SN3: reserved */ + +/* + * Status Register 2, Upper 16 Bits (ST2U) + */ +#define FM_SOTRBEC 0x0001 /* other beacon received */ +#define FM_SMYBEC 0x0002 /* my beacon received */ +#define FM_SBEC 0x0004 /* beacon state entered */ +#define FM_SLOCLM 0x0008 /* low claim received */ +#define FM_SHICLM 0x0010 /* high claim received */ +#define FM_SMYCLM 0x0020 /* my claim received */ +#define FM_SCLM 0x0040 /* claim state entered */ +#define FM_SERRSF 0x0080 /* error in special frame */ +#define FM_SNFSLD 0x0100 /* NP and FORMAC+ simultaneous load */ +#define FM_SRFRCTOV 0x0200 /* receive frame counter overflow */ + /* SN3: reserved */ +#define FM_SRCVFRM 0x0400 /* receive frame */ + /* SN3: reserved */ +#define FM_SRCVOVR 0x0800 /* receive FIFO overflow */ +#define FM_SRBFL 0x1000 /* receive buffer full */ +#define FM_SRABT 0x2000 /* receive abort */ +#define FM_SRBMT 0x4000 /* receive buffer empty */ +#define FM_SRCOMP 0x8000 /* receive complete. Nontag mode */ + +/* + * Status Register 2, Lower 16 Bits (ST2L) + * Attention: SN3 docu shows these bits the other way around + */ +#define FM_SRES0 0x0001 /* reserved */ +#define FM_SESTRIPTK 0x0001 /* SN3: 'no description' */ +#define FM_STRTEXR 0x0002 /* TRT expired in claim | beacon st. */ +#define FM_SDUPCLM 0x0004 /* duplicate claim received */ +#define FM_SSIFG 0x0008 /* short interframe gap */ +#define FM_SFRMCTR 0x0010 /* frame counter overflow */ +#define FM_SERRCTR 0x0020 /* error counter overflow */ +#define FM_SLSTCTR 0x0040 /* lost counter overflow */ +#define FM_SPHINV 0x0080 /* PHY invalid */ +#define FM_SADET 0x0100 /* address detect */ +#define FM_SMISFRM 0x0200 /* missed frame */ +#define FM_STRTEXP 0x0400 /* TRT expired and late count > 0 */ +#define FM_STVXEXP 0x0800 /* TVX expired */ +#define FM_STKISS 0x1000 /* token issued */ +#define FM_STKERR 0x2000 /* token error */ +#define FM_SMULTDA 0x4000 /* multiple destination address */ +#define FM_SRNGOP 0x8000 /* ring operational */ + +/* + * Supernet 3: + * Status Register 3, Upper 16 Bits (ST3U) + */ +#define FM_SRQUNLCK1 0x0001 /* receive queue unlocked queue 1 */ +#define FM_SRQUNLCK2 0x0002 /* receive queue unlocked queue 2 */ +#define FM_SRPERRQ1 0x0004 /* receive parity error rx queue 1 */ +#define FM_SRPERRQ2 0x0008 /* receive parity error rx queue 2 */ + /* Bit 4-10: reserved */ +#define FM_SRCVOVR2 0x0800 /* receive FIFO overfull rx queue 2 */ +#define FM_SRBFL2 0x1000 /* receive buffer full rx queue 2 */ +#define FM_SRABT2 0x2000 /* receive abort rx queue 2 */ +#define FM_SRBMT2 0x4000 /* receive buf empty rx queue 2 */ +#define FM_SRCOMP2 0x8000 /* receive comp rx queue 2 */ + +/* + * Supernet 3: + * Status Register 3, Lower 16 Bits (ST3L) + */ +#define FM_AF_BIST_DONE 0x0001 /* Address Filter BIST is done */ +#define FM_PLC_BIST_DONE 0x0002 /* internal PLC Bist is done */ +#define FM_PDX_BIST_DONE 0x0004 /* PDX BIST is done */ + /* Bit 3: reserved */ +#define FM_SICAMDAMAT 0x0010 /* Status internal CAM DA match */ +#define FM_SICAMDAXACT 0x0020 /* Status internal CAM DA exact match */ +#define FM_SICAMSAMAT 0x0040 /* Status internal CAM SA match */ +#define FM_SICAMSAXACT 0x0080 /* Status internal CAM SA exact match */ + +/* + * MAC State-Machine Register FM_STMCHN + */ +#define FM_MDRTAG 0x0004 /* tag bit of long word read */ +#define FM_SNPPND 0x0008 /* r/w from buffer mem. is pending */ +#define FM_TXSTAT 0x0070 /* transmitter state machine state */ +#define FM_RCSTAT 0x0380 /* receiver state machine state */ +#define FM_TM01 0x0c00 /* indicate token mode */ +#define FM_SIM 0x1000 /* indicate send immediate-mode */ +#define FM_REV 0xe000 /* FORMAC Plus revision number */ + +/* + * Supernet 3 + * Mode Register 3 + */ +#define FM_MENRS 0x0001 /* Ena enhanced rec status encoding */ +#define FM_MENXS 0x0002 /* Ena enhanced xmit status encoding */ +#define FM_MENXCT 0x0004 /* Ena EXACT/INEXACT matching */ +#define FM_MENAFULL 0x0008 /* Ena enh QCTRL encoding for AFULL */ +#define FM_MEIND 0x0030 /* Ena enh A,C indicator settings */ +#define FM_MENQCTRL 0x0040 /* Ena enh QCTRL encoding */ +#define FM_MENRQAUNLCK 0x0080 /* Ena rec q auto unlock */ +#define FM_MENDAS 0x0100 /* Ena DAS connections by cntr MUX */ +#define FM_MENPLCCST 0x0200 /* Ena Counter Segm test in PLC blck */ +#define FM_MENSGLINT 0x0400 /* Ena Vectored Interrupt reading */ +#define FM_MENDRCV 0x0800 /* Ena dual receive queue operation */ +#define FM_MENFCLOC 0x3000 /* Ena FC location within frm data */ +#define FM_MENTRCMD 0x4000 /* Ena ASYNC1 xmit only after command */ +#define FM_MENTDLPBK 0x8000 /* Ena TDAT to RDAT lkoopback */ + +/* + * Supernet 3 + * Frame Selection Register + */ +#define FM_RECV1 0x000f /* options for receive queue 1 */ +#define FM_RCV1_ALL (0<<0) /* receive all frames */ +#define FM_RCV1_LLC (1<<0) /* rec all LLC frames */ +#define FM_RCV1_SMT (2<<0) /* rec all SMT frames */ +#define FM_RCV1_NSMT (3<<0) /* rec non-SMT frames */ +#define FM_RCV1_IMP (4<<0) /* rec Implementor frames */ +#define FM_RCV1_MAC (5<<0) /* rec all MAC frames */ +#define FM_RCV1_SLLC (6<<0) /* rec all sync LLC frames */ +#define FM_RCV1_ALLC (7<<0) /* rec all async LLC frames */ +#define FM_RCV1_VOID (8<<0) /* rec all void frames */ +#define FM_RCV1_ALSMT (9<<0) /* rec all async LLC & SMT frames */ +#define FM_RECV2 0x00f0 /* options for receive queue 2 */ +#define FM_RCV2_ALL (0<<4) /* receive all other frames */ +#define FM_RCV2_LLC (1<<4) /* rec all LLC frames */ +#define FM_RCV2_SMT (2<<4) /* rec all SMT frames */ +#define FM_RCV2_NSMT (3<<4) /* rec non-SMT frames */ +#define FM_RCV2_IMP (4<<4) /* rec Implementor frames */ +#define FM_RCV2_MAC (5<<4) /* rec all MAC frames */ +#define FM_RCV2_SLLC (6<<4) /* rec all sync LLC frames */ +#define FM_RCV2_ALLC (7<<4) /* rec all async LLC frames */ +#define FM_RCV2_VOID (8<<4) /* rec all void frames */ +#define FM_RCV2_ALSMT (9<<4) /* rec all async LLC & SMT frames */ +#define FM_ENXMTADSWAP 0x4000 /* enh rec addr swap (phys -> can) */ +#define FM_ENRCVADSWAP 0x8000 /* enh tx addr swap (can -> phys) */ + +/* + * Supernet 3: + * Address Filter Command Register (AFCMD) + */ +#define FM_INST 0x0007 /* Address Filter Operation */ +#define FM_IINV_CAM (0<<0) /* Invalidate CAM */ +#define FM_IWRITE_CAM (1<<0) /* Write CAM */ +#define FM_IREAD_CAM (2<<0) /* Read CAM */ +#define FM_IRUN_BIST (3<<0) /* Run BIST */ +#define FM_IFIND (4<<0) /* Find */ +#define FM_IINV (5<<0) /* Invalidate */ +#define FM_ISKIP (6<<0) /* Skip */ +#define FM_ICL_SKIP (7<<0) /* Clear all SKIP bits */ + +/* + * Supernet 3: + * Address Filter Status Register (AFSTAT) + */ + /* Bit 0-4: reserved */ +#define FM_REV_NO 0x00e0 /* Revision Number of Address Filter */ +#define FM_BIST_DONE 0x0100 /* BIST complete */ +#define FM_EMPTY 0x0200 /* CAM empty */ +#define FM_ERROR 0x0400 /* Error (improper operation) */ +#define FM_MULT 0x0800 /* Multiple Match */ +#define FM_EXACT 0x1000 /* Exact Match */ +#define FM_FOUND 0x2000 /* Comparand found in CAM */ +#define FM_FULL 0x4000 /* CAM full */ +#define FM_DONE 0x8000 /* DONE indicator */ + +/* + * Supernet 3: + * BIST Signature Register (AFBIST) + */ +#define AF_BIST_SIGNAT 0x0553 /* Address Filter BIST Signature */ + +/* + * Supernet 3: + * Personality Register (AFPERS) + */ +#define FM_VALID 0x0001 /* CAM Entry Valid */ +#define FM_DA 0x0002 /* Destination Address */ +#define FM_DAX 0x0004 /* Destination Address Exact */ +#define FM_SA 0x0008 /* Source Address */ +#define FM_SAX 0x0010 /* Source Address Exact */ +#define FM_SKIP 0x0020 /* Skip this entry */ + +/* + * instruction set for command register 1 (NPADDR6-0 = 0x00) + */ +#define FM_IRESET 0x01 /* software reset */ +#define FM_IRMEMWI 0x02 /* load Memory Data Reg., inc MARR */ +#define FM_IRMEMWO 0x03 /* load MDR from buffer memory, n.i. */ +#define FM_IIL 0x04 /* idle/listen */ +#define FM_ICL 0x05 /* claim/listen */ +#define FM_IBL 0x06 /* beacon/listen */ +#define FM_ILTVX 0x07 /* load TVX timer from TVX reg */ +#define FM_INRTM 0x08 /* nonrestricted token mode */ +#define FM_IENTM 0x09 /* enter nonrestricted token mode */ +#define FM_IERTM 0x0a /* enter restricted token mode */ +#define FM_IRTM 0x0b /* restricted token mode */ +#define FM_ISURT 0x0c /* send unrestricted token */ +#define FM_ISRT 0x0d /* send restricted token */ +#define FM_ISIM 0x0e /* enter send-immediate mode */ +#define FM_IESIM 0x0f /* exit send-immediate mode */ +#define FM_ICLLS 0x11 /* clear synchronous queue lock */ +#define FM_ICLLA0 0x12 /* clear asynchronous queue 0 lock */ +#define FM_ICLLA1 0x14 /* clear asynchronous queue 1 lock */ +#define FM_ICLLA2 0x18 /* clear asynchronous queue 2 lock */ + /* SN3: reserved */ +#define FM_ICLLR 0x20 /* clear receive queue (SN3:1) lock */ +#define FM_ICLLR2 0x21 /* SN3: clear receive queue 2 lock */ +#define FM_ITRXBUS 0x22 /* SN3: Tristate X-Bus (SAS only) */ +#define FM_IDRXBUS 0x23 /* SN3: drive X-Bus */ +#define FM_ICLLAL 0x3f /* clear all queue locks */ + +/* + * instruction set for command register 2 (NPADDR6-0 = 0x01) + */ +#define FM_ITRS 0x01 /* transmit synchronous queue */ + /* SN3: reserved */ +#define FM_ITRA0 0x02 /* transmit asynchronous queue 0 */ + /* SN3: reserved */ +#define FM_ITRA1 0x04 /* transmit asynchronous queue 1 */ + /* SN3: reserved */ +#define FM_ITRA2 0x08 /* transmit asynchronous queue 2 */ + /* SN3: reserved */ +#define FM_IACTR 0x10 /* abort current transmit activity */ +#define FM_IRSTQ 0x20 /* reset transmit queues */ +#define FM_ISTTB 0x30 /* set tag bit */ +#define FM_IERSF 0x40 /* enable receive single frame */ + /* SN3: reserved */ +#define FM_ITR 0x50 /* SN3: Transmit Command */ + + +/* + * defines for PLC (Am79C864) + */ + +/* + * PLC read/write (r/w) registers + */ +#define PL_CNTRL_A 0x00 /* control register A (r/w) */ +#define PL_CNTRL_B 0x01 /* control register B (r/w) */ +#define PL_INTR_MASK 0x02 /* interrupt mask (r/w) */ +#define PL_XMIT_VECTOR 0x03 /* transmit vector register (r/w) */ +#define PL_VECTOR_LEN 0x04 /* transmit vector length (r/w) */ +#define PL_LE_THRESHOLD 0x05 /* link error event threshold (r/w) */ +#define PL_C_MIN 0x06 /* minimum connect state time (r/w) */ +#define PL_TL_MIN 0x07 /* min. line state transmit t. (r/w) */ +#define PL_TB_MIN 0x08 /* minimum break time (r/w) */ +#define PL_T_OUT 0x09 /* signal timeout (r/w) */ +#define PL_CNTRL_C 0x0a /* control register C (r/w) */ +#define PL_LC_LENGTH 0x0b /* link confidence test time (r/w) */ +#define PL_T_SCRUB 0x0c /* scrub time = MAC TVX (r/w) */ +#define PL_NS_MAX 0x0d /* max. noise time before break (r/w)*/ +#define PL_TPC_LOAD_V 0x0e /* TPC timer load value (write only) */ +#define PL_TNE_LOAD_V 0x0f /* TNE timer load value (write only) */ +#define PL_STATUS_A 0x10 /* status register A (read only) */ +#define PL_STATUS_B 0x11 /* status register B (read only) */ +#define PL_TPC 0x12 /* timer for PCM (ro) [20.48 us] */ +#define PL_TNE 0x13 /* time of noise event [0.32 us] */ +#define PL_CLK_DIV 0x14 /* TNE clock divider (read only) */ +#define PL_BIST_SIGNAT 0x15 /* built in self test signature (ro)*/ +#define PL_RCV_VECTOR 0x16 /* receive vector reg. (read only) */ +#define PL_INTR_EVENT 0x17 /* interrupt event reg. (read only) */ +#define PL_VIOL_SYM_CTR 0x18 /* violation symbol count. (read o) */ +#define PL_MIN_IDLE_CTR 0x19 /* minimum idle counter (read only) */ +#define PL_LINK_ERR_CTR 0x1a /* link error event ctr.(read only) */ +#ifdef MOT_ELM +#define PL_T_FOT_ASS 0x1e /* FOTOFF Assert Timer */ +#define PL_T_FOT_DEASS 0x1f /* FOTOFF Deassert Timer */ +#endif /* MOT_ELM */ + +#ifdef MOT_ELM +/* + * Special Quad-Elm Registers. + * A Quad-ELM consists of for ELMs and these additional registers. + */ +#define QELM_XBAR_W 0x80 /* Crossbar Control ELM W */ +#define QELM_XBAR_X 0x81 /* Crossbar Control ELM X */ +#define QELM_XBAR_Y 0x82 /* Crossbar Control ELM Y */ +#define QELM_XBAR_Z 0x83 /* Crossbar Control ELM Z */ +#define QELM_XBAR_P 0x84 /* Crossbar Control Bus P */ +#define QELM_XBAR_S 0x85 /* Crossbar Control Bus S */ +#define QELM_XBAR_R 0x86 /* Crossbar Control Bus R */ +#define QELM_WR_XBAR 0x87 /* Write the Crossbar now (write) */ +#define QELM_CTR_W 0x88 /* Counter W */ +#define QELM_CTR_X 0x89 /* Counter X */ +#define QELM_CTR_Y 0x8a /* Counter Y */ +#define QELM_CTR_Z 0x8b /* Counter Z */ +#define QELM_INT_MASK 0x8c /* Interrupt mask register */ +#define QELM_INT_DATA 0x8d /* Interrupt data (event) register */ +#define QELM_ELMB 0x00 /* Elm base */ +#define QELM_ELM_SIZE 0x20 /* ELM size */ +#endif /* MOT_ELM */ +/* + * PLC control register A (PL_CNTRL_A: log. addr. 0x00) + * It is used for timer configuration, specification of PCM MAINT state option, + * counter interrupt frequency, PLC data path config. and Built In Self Test. + */ +#define PL_RUN_BIST 0x0001 /* begin running its Built In Self T.*/ +#define PL_RF_DISABLE 0x0002 /* disable the Repeat Filter state m.*/ +#define PL_SC_REM_LOOP 0x0004 /* remote loopback path */ +#define PL_SC_BYPASS 0x0008 /* by providing a physical bypass */ +#define PL_LM_LOC_LOOP 0x0010 /* loop path just after elastic buff.*/ +#define PL_EB_LOC_LOOP 0x0020 /* loop path just prior to PDT/PDR IF*/ +#define PL_FOT_OFF 0x0040 /* assertion of /FOTOFF pin of PLC */ +#define PL_LOOPBACK 0x0080 /* it cause the /LPBCK pin ass. low */ +#define PL_MINI_CTR_INT 0x0100 /* partially contr. when bit is ass. */ +#define PL_VSYM_CTR_INT 0x0200 /* controls when int bit is asserted */ +#define PL_ENA_PAR_CHK 0x0400 /* enable parity check */ +#define PL_REQ_SCRUB 0x0800 /* limited access to scrub capability*/ +#define PL_TPC_16BIT 0x1000 /* causes the TPC as a 16 bit timer */ +#define PL_TNE_16BIT 0x2000 /* causes the TNE as a 16 bit timer */ +#define PL_NOISE_TIMER 0x4000 /* allows the noise timing function */ + +/* + * PLC control register B (PL_CNTRL_B: log. addr. 0x01) + * It contains signals and requeste to direct the process of PCM and it is also + * used to control the Line State Match interrupt. + */ +#define PL_PCM_CNTRL 0x0003 /* control PCM state machine */ +#define PL_PCM_NAF (0) /* state is not affected */ +#define PL_PCM_START (1) /* goes to the BREAK state */ +#define PL_PCM_TRACE (2) /* goes to the TRACE state */ +#define PL_PCM_STOP (3) /* goes to the OFF state */ + +#define PL_MAINT 0x0004 /* if OFF state --> MAINT state */ +#define PL_LONG 0x0008 /* perf. a long Link Confid.Test(LCT)*/ +#define PL_PC_JOIN 0x0010 /* if NEXT state --> JOIN state */ + +#define PL_PC_LOOP 0x0060 /* loopback used in the LCT */ +#define PL_NOLCT (0<<5) /* no LCT is performed */ +#define PL_TPDR (1<<5) /* PCM asserts transmit PDR */ +#define PL_TIDLE (2<<5) /* PCM asserts transmit idle */ +#define PL_RLBP (3<<5) /* trans. PDR & remote loopb. path */ + +#define PL_CLASS_S 0x0080 /* signif. that single att. station */ + +#define PL_MAINT_LS 0x0700 /* line state while in the MAINT st. */ +#define PL_M_QUI0 (0<<8) /* transmit QUIET line state */ +#define PL_M_IDLE (1<<8) /* transmit IDLE line state */ +#define PL_M_HALT (2<<8) /* transmit HALT line state */ +#define PL_M_MASTR (3<<8) /* transmit MASTER line state */ +#define PL_M_QUI1 (4<<8) /* transmit QUIET line state */ +#define PL_M_QUI2 (5<<8) /* transmit QUIET line state */ +#define PL_M_TPDR (6<<8) /* tr. PHY_DATA requ.-symbol is tr.ed*/ +#define PL_M_QUI3 (7<<8) /* transmit QUIET line state */ + +#define PL_MATCH_LS 0x7800 /* line state to be comp. with curr.*/ +#define PL_I_ANY (0<<11) /* Int. on any change in *_LINE_ST */ +#define PL_I_IDLE (1<<11) /* Interrupt on IDLE line state */ +#define PL_I_HALT (2<<11) /* Interrupt on HALT line state */ +#define PL_I_MASTR (4<<11) /* Interrupt on MASTER line state */ +#define PL_I_QUIET (8<<11) /* Interrupt on QUIET line state */ + +#define PL_CONFIG_CNTRL 0x8000 /* control over scrub, byp. & loopb.*/ + +/* + * PLC control register C (PL_CNTRL_C: log. addr. 0x0a) + * It contains the scrambling control registers (PLC-S only) + */ +#define PL_C_CIPHER_ENABLE (1<<0) /* enable scrambler */ +#define PL_C_CIPHER_LPBCK (1<<1) /* loopback scrambler */ +#define PL_C_SDOFF_ENABLE (1<<6) /* enable SDOFF timer */ +#define PL_C_SDON_ENABLE (1<<7) /* enable SDON timer */ +#ifdef MOT_ELM +#define PL_C_FOTOFF_CTRL (3<<2) /* FOTOFF timer control */ +#define PL_C_FOTOFF_TIM (0<<2) /* FOTOFF use timer for (de)-assert */ +#define PL_C_FOTOFF_INA (2<<2) /* FOTOFF forced inactive */ +#define PL_C_FOTOFF_ACT (3<<2) /* FOTOFF forced active */ +#define PL_C_FOTOFF_SRCE (1<<4) /* FOTOFF source is PCM state != OFF */ +#define PL_C_RXDATA_EN (1<<5) /* Rec scr data forced to 0 */ +#define PL_C_SDNRZEN (1<<8) /* Monitor rec descr. data for act */ +#else /* nMOT_ELM */ +#define PL_C_FOTOFF_CTRL (3<<8) /* FOTOFF timer control */ +#define PL_C_FOTOFF_0 (0<<8) /* timer off */ +#define PL_C_FOTOFF_30 (1<<8) /* 30uS */ +#define PL_C_FOTOFF_50 (2<<8) /* 50uS */ +#define PL_C_FOTOFF_NEVER (3<<8) /* never */ +#define PL_C_SDON_TIMER (3<<10) /* SDON timer control */ +#define PL_C_SDON_084 (0<<10) /* 0.84 uS */ +#define PL_C_SDON_132 (1<<10) /* 1.32 uS */ +#define PL_C_SDON_252 (2<<10) /* 2.52 uS */ +#define PL_C_SDON_512 (3<<10) /* 5.12 uS */ +#define PL_C_SOFF_TIMER (3<<12) /* SDOFF timer control */ +#define PL_C_SOFF_076 (0<<12) /* 0.76 uS */ +#define PL_C_SOFF_132 (1<<12) /* 1.32 uS */ +#define PL_C_SOFF_252 (2<<12) /* 2.52 uS */ +#define PL_C_SOFF_512 (3<<12) /* 5.12 uS */ +#define PL_C_TSEL (3<<14) /* scrambler path select */ +#endif /* nMOT_ELM */ + +/* + * PLC status register A (PL_STATUS_A: log. addr. 0x10) + * It is used to report status information to the Node Processor about the + * Line State Machine (LSM). + */ +#ifdef MOT_ELM +#define PLC_INT_MASK 0xc000 /* ELM integration bits in status A */ +#define PLC_INT_C 0x0000 /* ELM Revision Band C */ +#define PLC_INT_CAMEL 0x4000 /* ELM integrated into CAMEL */ +#define PLC_INT_QE 0x8000 /* ELM integrated into Quad ELM */ +#define PLC_REV_MASK 0x3800 /* revision bits in status A */ +#define PLC_REVISION_B 0x0000 /* rev bits for ELM Rev B */ +#define PLC_REVISION_QA 0x0800 /* rev bits for ELM core in QELM-A */ +#else /* nMOT_ELM */ +#define PLC_REV_MASK 0xf800 /* revision bits in status A */ +#define PLC_REVISION_A 0x0000 /* revision bits for PLC */ +#define PLC_REVISION_S 0xf800 /* revision bits for PLC-S */ +#define PLC_REV_SN3 0x7800 /* revision bits for PLC-S in IFCP */ +#endif /* nMOT_ELM */ +#define PL_SYM_PR_CTR 0x0007 /* contains the LSM symbol pair Ctr. */ +#define PL_UNKN_LINE_ST 0x0008 /* unknown line state bit from LSM */ +#define PL_LSM_STATE 0x0010 /* state bit of LSM */ + +#define PL_LINE_ST 0x00e0 /* contains recogn. line state of LSM*/ +#define PL_L_NLS (0<<5) /* noise line state */ +#define PL_L_ALS (1<<5) /* activ line state */ +#define PL_L_UND (2<<5) /* undefined */ +#define PL_L_ILS4 (3<<5) /* idle l. s. (after 4 idle symbols) */ +#define PL_L_QLS (4<<5) /* quiet line state */ +#define PL_L_MLS (5<<5) /* master line state */ +#define PL_L_HLS (6<<5) /* halt line state */ +#define PL_L_ILS16 (7<<5) /* idle line state (after 16 idle s.)*/ + +#define PL_PREV_LINE_ST 0x0300 /* value of previous line state */ +#define PL_P_QLS (0<<8) /* quiet line state */ +#define PL_P_MLS (1<<8) /* master line state */ +#define PL_P_HLS (2<<8) /* halt line state */ +#define PL_P_ILS16 (3<<8) /* idle line state (after 16 idle s.)*/ + +#define PL_SIGNAL_DET 0x0400 /* 1=that signal detect is deasserted*/ + + +/* + * PLC status register B (PL_STATUS_B: log. addr. 0x11) + * It contains signals and status from the repeat filter and PCM state machine. + */ +#define PL_BREAK_REASON 0x0007 /* reason for PCM state mach.s to br.*/ +#define PL_B_NOT (0) /* PCM SM has not gone to BREAK state*/ +#define PL_B_PCS (1) /* PC_Start issued */ +#define PL_B_TPC (2) /* TPC timer expired after T_OUT */ +#define PL_B_TNE (3) /* TNE timer expired after NS_MAX */ +#define PL_B_QLS (4) /* quit line state detected */ +#define PL_B_ILS (5) /* idle line state detected */ +#define PL_B_HLS (6) /* halt line state detected */ + +#define PL_TCF 0x0008 /* transmit code flag (start exec.) */ +#define PL_RCF 0x0010 /* receive code flag (start exec.) */ +#define PL_LSF 0x0020 /* line state flag (l.s. has been r.)*/ +#define PL_PCM_SIGNAL 0x0040 /* indic. that XMIT_VECTOR hb.written*/ + +#define PL_PCM_STATE 0x0780 /* state bits of PCM state machine */ +#define PL_PC0 (0<<7) /* OFF - when /RST or PCM_CNTRL */ +#define PL_PC1 (1<<7) /* BREAK - entry point in start PCM*/ +#define PL_PC2 (2<<7) /* TRACE - to localize stuck Beacon*/ +#define PL_PC3 (3<<7) /* CONNECT - synchronize ends of conn*/ +#define PL_PC4 (4<<7) /* NEXT - to separate the signalng*/ +#define PL_PC5 (5<<7) /* SIGNAL - PCM trans/rec. bit infos*/ +#define PL_PC6 (6<<7) /* JOIN - 1. state to activ conn. */ +#define PL_PC7 (7<<7) /* VERIFY - 2. - " - (3. ACTIVE) */ +#define PL_PC8 (8<<7) /* ACTIVE - PHY has been incorporated*/ +#define PL_PC9 (9<<7) /* MAINT - for test purposes or so + that PCM op. completely in softw. */ + +#define PL_PCI_SCRUB 0x0800 /* scrubbing function is being exec. */ + +#define PL_PCI_STATE 0x3000 /* Physical Connect. Insertion SM */ +#define PL_CI_REMV (0<<12) /* REMOVED */ +#define PL_CI_ISCR (1<<12) /* INSERT_SCRUB */ +#define PL_CI_RSCR (2<<12) /* REMOVE_SCRUB */ +#define PL_CI_INS (3<<12) /* INSERTED */ + +#define PL_RF_STATE 0xc000 /* state bit of repeate filter SM */ +#define PL_RF_REPT (0<<14) /* REPEAT */ +#define PL_RF_IDLE (1<<14) /* IDLE */ +#define PL_RF_HALT1 (2<<14) /* HALT1 */ +#define PL_RF_HALT2 (3<<14) /* HALT2 */ + + +/* + * PLC interrupt event register (PL_INTR_EVENT: log. addr. 0x17) + * It is read only and is clearde whenever it is read! + * It is used by the PLC to report events to the node processor. + */ +#define PL_PARITY_ERR 0x0001 /* p. error h.b.detected on TX9-0 inp*/ +#define PL_LS_MATCH 0x0002 /* l.s.== l.s. PLC_CNTRL_B's MATCH_LS*/ +#define PL_PCM_CODE 0x0004 /* transmit&receive | LCT complete */ +#define PL_TRACE_PROP 0x0008 /* master l.s. while PCM ACTIV|TRACE */ +#define PL_SELF_TEST 0x0010 /* QUIET|HALT while PCM in TRACE st. */ +#define PL_PCM_BREAK 0x0020 /* PCM has entered the BREAK state */ +#define PL_PCM_ENABLED 0x0040 /* asserted SC_JOIN, scrub. & ACTIV */ +#define PL_TPC_EXPIRED 0x0080 /* TPC timer reached zero */ +#define PL_TNE_EXPIRED 0x0100 /* TNE timer reached zero */ +#define PL_EBUF_ERR 0x0200 /* elastic buff. det. over-|underflow*/ +#define PL_PHYINV 0x0400 /* physical layer invalid signal */ +#define PL_VSYM_CTR 0x0800 /* violation symbol counter has incr.*/ +#define PL_MINI_CTR 0x1000 /* dep. on PLC_CNTRL_A's MINI_CTR_INT*/ +#define PL_LE_CTR 0x2000 /* link error event counter */ +#define PL_LSDO 0x4000 /* SDO input pin changed to a 1 */ +#define PL_NP_ERR 0x8000 /* NP has requested to r/w an inv. r.*/ + +/* + * The PLC interrupt mask register (PL_INTR_MASK: log. addr. 0x02) constr. is + * equal PL_INTR_EVENT register. + * For each set bit, the setting of corresponding bit generate an int to NP. + */ + +#ifdef MOT_ELM +/* + * Quad ELM Crosbar Control register values (QELM_XBAR_?) + */ +#define QELM_XOUT_IDLE 0x0000 /* Idles/Passthrough */ +#define QELM_XOUT_P 0x0001 /* Output to: Bus P */ +#define QELM_XOUT_S 0x0002 /* Output to: Bus S */ +#define QELM_XOUT_R 0x0003 /* Output to: Bus R */ +#define QELM_XOUT_W 0x0004 /* Output to: ELM W */ +#define QELM_XOUT_X 0x0005 /* Output to: ELM X */ +#define QELM_XOUT_Y 0x0006 /* Output to: ELM Y */ +#define QELM_XOUT_Z 0x0007 /* Output to: ELM Z */ + +/* + * Quad ELM Interrupt data and event registers. + */ +#define QELM_NP_ERR (1<<15) /* Node Processor Error */ +#define QELM_COUNT_Z (1<<7) /* Counter Z Interrupt */ +#define QELM_COUNT_Y (1<<6) /* Counter Y Interrupt */ +#define QELM_COUNT_X (1<<5) /* Counter X Interrupt */ +#define QELM_COUNT_W (1<<4) /* Counter W Interrupt */ +#define QELM_ELM_Z (1<<3) /* ELM Z Interrupt */ +#define QELM_ELM_Y (1<<2) /* ELM Y Interrupt */ +#define QELM_ELM_X (1<<1) /* ELM X Interrupt */ +#define QELM_ELM_W (1<<0) /* ELM W Interrupt */ +#endif /* MOT_ELM */ +/* + * PLC Timing Parameters + */ +#define TP_C_MIN 0xff9c /* 2 ms */ +#define TP_TL_MIN 0xfff0 /* 0.3 ms */ +#define TP_TB_MIN 0xff10 /* 5 ms */ +#define TP_T_OUT 0xd9db /* 200 ms */ +#define TP_LC_LENGTH 0xf676 /* 50 ms */ +#define TP_LC_LONGLN 0xa0a2 /* 500 ms */ +#define TP_T_SCRUB 0xff6d /* 3.5 ms */ +#define TP_NS_MAX 0xf021 /* 1.3 ms */ + +/* + * BIST values + */ +#define PLC_BIST 0x6ecd /* BIST signature for PLC */ +#define PLCS_BIST 0x5b6b /* BIST signature for PLC-S */ +#define PLC_ELM_B_BIST 0x6ecd /* BIST signature of ELM Rev. B */ +#define PLC_ELM_D_BIST 0x5b6b /* BIST signature of ELM Rev. D */ +#define PLC_CAM_A_BIST 0x9e75 /* BIST signature of CAMEL Rev. A */ +#define PLC_CAM_B_BIST 0x5b6b /* BIST signature of CAMEL Rev. B */ +#define PLC_IFD_A_BIST 0x9e75 /* BIST signature of IFDDI Rev. A */ +#define PLC_IFD_B_BIST 0x5b6b /* BIST signature of IFDDI Rev. B */ +#define PLC_QELM_A_BIST 0x5b6b /* BIST signature of QELM Rev. A */ + +/* + FDDI board recources + */ + +/* + * request register array (log. addr: RQA_A + a<<1 {a=0..7}) write only. + * It specifies to FORMAC+ the type of buffer memory access the host requires. + */ +#define RQ_NOT 0 /* not request */ +#define RQ_RES 1 /* reserved */ +#define RQ_SFW 2 /* special frame write */ +#define RQ_RRQ 3 /* read request: receive queue */ +#define RQ_WSQ 4 /* write request: synchronous queue */ +#define RQ_WA0 5 /* write requ.: asynchronous queue 0 */ +#define RQ_WA1 6 /* write requ.: asynchronous queue 1 */ +#define RQ_WA2 7 /* write requ.: asynchronous queue 2 */ + +#define SZ_LONG (sizeof(long)) + +/* + * FDDI defaults + * NOTE : In the ANSI docs, times are specified in units of "symbol time". + * AMD chips use BCLK as unit. 1 BCKL == 2 symbols + */ +#define COMPLREF ((u_long)32*256*256) /* two's complement 21 bit */ +#define MSTOBCLK(x) ((u_long)(x)*12500L) +#define MSTOTVX(x) (((u_long)(x)*1000L)/80/255) + +#endif /* _SUPERNET_ */ diff --git a/kernel/drivers/net/fddi/skfp/h/targethw.h b/kernel/drivers/net/fddi/skfp/h/targethw.h new file mode 100644 index 000000000..842a69044 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/targethw.h @@ -0,0 +1,138 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef _TARGETHW_ +#define _TARGETHW_ + + /* + * PCI Watermark definition + */ +#ifdef PCI +#define RX_WATERMARK 24 +#define TX_WATERMARK 24 +#define SK_ML_ID_1 0x20 +#define SK_ML_ID_2 0x30 +#endif + +#include "skfbi.h" +#ifndef TAG_MODE +#include "fplus.h" +#else +#include "fplustm.h" +#endif + +#ifndef HW_PTR +#define HW_PTR void __iomem * +#endif + +#ifdef MULT_OEM +#define OI_STAT_LAST 0 /* end of OEM data base */ +#define OI_STAT_PRESENT 1 /* entry present but not empty */ +#define OI_STAT_VALID 2 /* holds valid ID, but is not active */ +#define OI_STAT_ACTIVE 3 /* holds valid ID, entry is active */ + /* active = adapter is supported */ + +/* Memory representation of IDs must match representation in adapter. */ +struct s_oem_ids { + u_char oi_status ; /* Stat: last, present, valid, active */ + u_char oi_mark[5] ; /* "PID00" .. "PID07" .. */ + u_char oi_id[4] ; /* id bytes, representation as */ + /* defined by hardware, */ +#ifdef PCI + u_char oi_sub_id[4] ; /* sub id bytes, representation as */ + /* defined by hardware, */ +#endif +} ; +#endif /* MULT_OEM */ + + +struct s_smt_hw { + /* + * global + */ + HW_PTR iop ; /* IO base address */ + short dma ; /* DMA channel */ + short irq ; /* IRQ level */ + short eprom ; /* FLASH prom */ + +#ifndef SYNC + u_short n_a_send ; /* pending send requests */ +#endif + +#if defined(PCI) + short slot ; /* slot number */ + short max_slots ; /* maximum number of slots */ + short wdog_used ; /* TRUE if the watch dog is used */ +#endif + +#ifdef PCI + u_short pci_handle ; /* handle to access the BIOS func */ + u_long is_imask ; /* int maske for the int source reg */ + u_long phys_mem_addr ; /* physical memory address */ + u_short mc_dummy ; /* work around for MC compiler bug */ + /* + * state of the hardware + */ + u_short hw_state ; /* started or stopped */ + +#define STARTED 1 +#define STOPPED 0 + + int hw_is_64bit ; /* does we have a 64 bit adapter */ +#endif + +#ifdef TAG_MODE + u_long pci_fix_value ; /* value parsed by PCIFIX */ +#endif + + /* + * hwt.c + */ + u_long t_start ; /* HWT start */ + u_long t_stop ; /* HWT stop */ + u_short timer_activ ; /* HWT timer active */ + + /* + * PIC + */ + u_char pic_a1 ; + u_char pic_21 ; + + /* + * GENERIC ; do not modify beyond this line + */ + + /* + * physical and canonical address + */ + struct fddi_addr fddi_home_addr ; + struct fddi_addr fddi_canon_addr ; + struct fddi_addr fddi_phys_addr ; + + /* + * mac variables + */ + struct mac_parameter mac_pa ; /* tmin, tmax, tvx, treq .. */ + struct mac_counter mac_ct ; /* recv., lost, error */ + u_short mac_ring_is_up ; /* ring is up flag */ + + struct s_smt_fp fp ; /* formac+ */ + +#ifdef MULT_OEM + struct s_oem_ids *oem_id ; /* pointer to selected id */ + int oem_min_status ; /* IDs to take care of */ +#endif /* MULT_OEM */ + +} ; +#endif diff --git a/kernel/drivers/net/fddi/skfp/h/targetos.h b/kernel/drivers/net/fddi/skfp/h/targetos.h new file mode 100644 index 000000000..355194251 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/targetos.h @@ -0,0 +1,164 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * Operating system specific definitions for driver and + * hardware module. + */ + +#ifndef TARGETOS_H +#define TARGETOS_H + + +//-------- those should go into include/linux/pci.h +#define PCI_VENDOR_ID_SK 0x1148 +#define PCI_DEVICE_ID_SK_FP 0x4000 +//-------- + + + +//-------- those should go into include/linux/if_fddi.h +#define FDDI_MAC_HDR_LEN 13 + +#define FDDI_RII 0x01 /* routing information bit */ +#define FDDI_RCF_DIR_BIT 0x80 +#define FDDI_RCF_LEN_MASK 0x1f +#define FDDI_RCF_BROADCAST 0x8000 +#define FDDI_RCF_LIMITED_BROADCAST 0xA000 +#define FDDI_RCF_FRAME2K 0x20 +#define FDDI_RCF_FRAME4K 0x30 +//-------- + + +#undef ADDR + +#include <asm/io.h> +#include <linux/netdevice.h> +#include <linux/fddidevice.h> +#include <linux/skbuff.h> +#include <linux/pci.h> + +// is redefined by linux, but we need our definition +#undef ADDR +#ifdef MEM_MAPPED_IO +#define ADDR(a) (smc->hw.iop+(a)) +#else +#define ADDR(a) (((a)>>7) ? (outp(smc->hw.iop+B0_RAP,(a)>>7), (smc->hw.iop+( ((a)&0x7F) | ((a)>>7 ? 0x80:0)) )) : (smc->hw.iop+(((a)&0x7F)|((a)>>7 ? 0x80:0)))) +#endif + +#include "hwmtm.h" + +#define TRUE 1 +#define FALSE 0 + +// HWM Definitions +// ----------------------- +#define FDDI_TRACE(string, arg1, arg2, arg3) // Performance analysis. +#ifdef PCI +#define NDD_TRACE(string, arg1, arg2, arg3) // Performance analysis. +#endif // PCI +#define SMT_PAGESIZE PAGE_SIZE // Size of a memory page (power of 2). +// ----------------------- + + +// SMT Definitions +// ----------------------- +#define TICKS_PER_SECOND HZ +#define SMC_VERSION 1 +// ----------------------- + + +// OS-Driver Definitions +// ----------------------- +#define NO_ADDRESS 0xffe0 /* No Device (I/O) Address */ +#define SKFP_MAX_NUM_BOARDS 8 /* maximum number of PCI boards */ + +#define SK_BUS_TYPE_PCI 0 +#define SK_BUS_TYPE_EISA 1 + +#define FP_IO_LEN 256 /* length of IO area used */ + +#define u8 unsigned char +#define u16 unsigned short +#define u32 unsigned int + +#define MAX_TX_QUEUE_LEN 20 // number of packets queued by driver +#define MAX_FRAME_SIZE 4550 + +#define RX_LOW_WATERMARK NUM_RECEIVE_BUFFERS / 2 +#define TX_LOW_WATERMARK NUM_TRANSMIT_BUFFERS - 2 + +/* +** Include the IOCTL stuff +*/ +#include <linux/sockios.h> + +#define SKFPIOCTL SIOCDEVPRIVATE + +struct s_skfp_ioctl { + unsigned short cmd; /* Command to run */ + unsigned short len; /* Length of the data buffer */ + unsigned char __user *data; /* Pointer to the data buffer */ +}; + +/* +** Recognised ioctl commands for the driver +*/ +#define SKFP_GET_STATS 0x05 /* Get the driver statistics */ +#define SKFP_CLR_STATS 0x06 /* Zero out the driver statistics */ + +// The per-adapter driver structure +struct s_smt_os { + struct net_device *dev; + struct net_device *next_module; + u32 bus_type; /* bus type (0 == PCI, 1 == EISA) */ + struct pci_dev pdev; /* PCI device structure */ + + unsigned long base_addr; + unsigned char factory_mac_addr[8]; + ulong SharedMemSize; + ulong SharedMemHeap; + void* SharedMemAddr; + dma_addr_t SharedMemDMA; + + ulong QueueSkb; + struct sk_buff_head SendSkbQueue; + + ulong MaxFrameSize; + u8 ResetRequested; + + // MAC statistics structure + struct fddi_statistics MacStat; + + // receive into this local buffer if no skb available + // data will be not valid, because multiple RxDs can + // point here at the same time, it must be at least + // MAX_FRAME_SIZE bytes in size + unsigned char *LocalRxBuffer; + dma_addr_t LocalRxBufferDMA; + + // Version (required by SMT module). + u_long smc_version ; + + // Required by Hardware Module (HWM). + struct hw_modul hwm ; + + // For SMP-savety + spinlock_t DriverLock; + +}; + +typedef struct s_smt_os skfddi_priv; + +#endif // _TARGETOS_ diff --git a/kernel/drivers/net/fddi/skfp/h/types.h b/kernel/drivers/net/fddi/skfp/h/types.h new file mode 100644 index 000000000..5a3bf8378 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/h/types.h @@ -0,0 +1,39 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#include <linux/types.h> +/* + ---------------------- + Basic SMT system types + ---------------------- +*/ +#ifndef _TYPES_ +#define _TYPES_ + +#define _packed +#ifndef far +#define far +#endif +#ifndef _far +#define _far +#endif + +#define inp(p) ioread8(p) +#define inpw(p) ioread16(p) +#define inpd(p) ioread32(p) +#define outp(p,c) iowrite8(c,p) +#define outpw(p,s) iowrite16(s,p) +#define outpd(p,l) iowrite32(l,p) + +#endif /* _TYPES_ */ diff --git a/kernel/drivers/net/fddi/skfp/hwmtm.c b/kernel/drivers/net/fddi/skfp/hwmtm.c new file mode 100644 index 000000000..e26398b5a --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/hwmtm.c @@ -0,0 +1,2178 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#ifndef lint +static char const ID_sccs[] = "@(#)hwmtm.c 1.40 99/05/31 (C) SK" ; +#endif + +#define HWMTM + +#ifndef FDDI +#define FDDI +#endif + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/supern_2.h" +#include "h/skfbiinc.h" + +/* + ------------------------------------------------------------- + DOCUMENTATION + ------------------------------------------------------------- + BEGIN_MANUAL_ENTRY(DOCUMENTATION) + + T B D + + END_MANUAL_ENTRY +*/ +/* + ------------------------------------------------------------- + LOCAL VARIABLES: + ------------------------------------------------------------- +*/ +#ifdef COMMON_MB_POOL +static SMbuf *mb_start = 0 ; +static SMbuf *mb_free = 0 ; +static int mb_init = FALSE ; +static int call_count = 0 ; +#endif + +/* + ------------------------------------------------------------- + EXTERNE VARIABLES: + ------------------------------------------------------------- +*/ + +#ifdef DEBUG +#ifndef DEBUG_BRD +extern struct smt_debug debug ; +#endif +#endif + +#ifdef NDIS_OS2 +extern u_char offDepth ; +extern u_char force_irq_pending ; +#endif + +/* + ------------------------------------------------------------- + LOCAL FUNCTIONS: + ------------------------------------------------------------- +*/ + +static void queue_llc_rx(struct s_smc *smc, SMbuf *mb); +static void smt_to_llc(struct s_smc *smc, SMbuf *mb); +static void init_txd_ring(struct s_smc *smc); +static void init_rxd_ring(struct s_smc *smc); +static void queue_txd_mb(struct s_smc *smc, SMbuf *mb); +static u_long init_descr_ring(struct s_smc *smc, union s_fp_descr volatile *start, + int count); +static u_long repair_txd_ring(struct s_smc *smc, struct s_smt_tx_queue *queue); +static u_long repair_rxd_ring(struct s_smc *smc, struct s_smt_rx_queue *queue); +static SMbuf* get_llc_rx(struct s_smc *smc); +static SMbuf* get_txd_mb(struct s_smc *smc); +static void mac_drv_clear_txd(struct s_smc *smc); + +/* + ------------------------------------------------------------- + EXTERNAL FUNCTIONS: + ------------------------------------------------------------- +*/ +/* The external SMT functions are listed in cmtdef.h */ + +extern void* mac_drv_get_space(struct s_smc *smc, unsigned int size); +extern void* mac_drv_get_desc_mem(struct s_smc *smc, unsigned int size); +extern void mac_drv_fill_rxd(struct s_smc *smc); +extern void mac_drv_tx_complete(struct s_smc *smc, + volatile struct s_smt_fp_txd *txd); +extern void mac_drv_rx_complete(struct s_smc *smc, + volatile struct s_smt_fp_rxd *rxd, + int frag_count, int len); +extern void mac_drv_requeue_rxd(struct s_smc *smc, + volatile struct s_smt_fp_rxd *rxd, + int frag_count); +extern void mac_drv_clear_rxd(struct s_smc *smc, + volatile struct s_smt_fp_rxd *rxd, int frag_count); + +#ifdef USE_OS_CPY +extern void hwm_cpy_rxd2mb(void); +extern void hwm_cpy_txd2mb(void); +#endif + +#ifdef ALL_RX_COMPLETE +extern void mac_drv_all_receives_complete(void); +#endif + +extern u_long mac_drv_virt2phys(struct s_smc *smc, void *virt); +extern u_long dma_master(struct s_smc *smc, void *virt, int len, int flag); + +#ifdef NDIS_OS2 +extern void post_proc(void); +#else +extern void dma_complete(struct s_smc *smc, volatile union s_fp_descr *descr, + int flag); +#endif + +extern int mac_drv_rx_init(struct s_smc *smc, int len, int fc, char *look_ahead, + int la_len); + +/* + ------------------------------------------------------------- + PUBLIC FUNCTIONS: + ------------------------------------------------------------- +*/ +void process_receive(struct s_smc *smc); +void fddi_isr(struct s_smc *smc); +void smt_free_mbuf(struct s_smc *smc, SMbuf *mb); +void init_driver_fplus(struct s_smc *smc); +void mac_drv_rx_mode(struct s_smc *smc, int mode); +void init_fddi_driver(struct s_smc *smc, u_char *mac_addr); +void mac_drv_clear_tx_queue(struct s_smc *smc); +void mac_drv_clear_rx_queue(struct s_smc *smc); +void hwm_tx_frag(struct s_smc *smc, char far *virt, u_long phys, int len, + int frame_status); +void hwm_rx_frag(struct s_smc *smc, char far *virt, u_long phys, int len, + int frame_status); + +int mac_drv_init(struct s_smc *smc); +int hwm_tx_init(struct s_smc *smc, u_char fc, int frag_count, int frame_len, + int frame_status); + +u_int mac_drv_check_space(void); + +SMbuf* smt_get_mbuf(struct s_smc *smc); + +#ifdef DEBUG + void mac_drv_debug_lev(void); +#endif + +/* + ------------------------------------------------------------- + MACROS: + ------------------------------------------------------------- +*/ +#ifndef UNUSED +#ifdef lint +#define UNUSED(x) (x) = (x) +#else +#define UNUSED(x) +#endif +#endif + +#ifdef USE_CAN_ADDR +#define MA smc->hw.fddi_canon_addr.a +#define GROUP_ADDR_BIT 0x01 +#else +#define MA smc->hw.fddi_home_addr.a +#define GROUP_ADDR_BIT 0x80 +#endif + +#define RXD_TXD_COUNT (HWM_ASYNC_TXD_COUNT+HWM_SYNC_TXD_COUNT+\ + SMT_R1_RXD_COUNT+SMT_R2_RXD_COUNT) + +#ifdef MB_OUTSIDE_SMC +#define EXT_VIRT_MEM ((RXD_TXD_COUNT+1)*sizeof(struct s_smt_fp_txd) +\ + MAX_MBUF*sizeof(SMbuf)) +#define EXT_VIRT_MEM_2 ((RXD_TXD_COUNT+1)*sizeof(struct s_smt_fp_txd)) +#else +#define EXT_VIRT_MEM ((RXD_TXD_COUNT+1)*sizeof(struct s_smt_fp_txd)) +#endif + + /* + * define critical read for 16 Bit drivers + */ +#if defined(NDIS_OS2) || defined(ODI2) +#define CR_READ(var) ((var) & 0xffff0000 | ((var) & 0xffff)) +#else +#define CR_READ(var) (__le32)(var) +#endif + +#define IMASK_SLOW (IS_PLINT1 | IS_PLINT2 | IS_TIMINT | IS_TOKEN | \ + IS_MINTR1 | IS_MINTR2 | IS_MINTR3 | IS_R1_P | \ + IS_R1_C | IS_XA_C | IS_XS_C) + +/* + ------------------------------------------------------------- + INIT- AND SMT FUNCTIONS: + ------------------------------------------------------------- +*/ + + +/* + * BEGIN_MANUAL_ENTRY(mac_drv_check_space) + * u_int mac_drv_check_space() + * + * function DOWNCALL (drvsr.c) + * This function calculates the needed non virtual + * memory for MBufs, RxD and TxD descriptors etc. + * needed by the driver. + * + * return u_int memory in bytes + * + * END_MANUAL_ENTRY + */ +u_int mac_drv_check_space(void) +{ +#ifdef MB_OUTSIDE_SMC +#ifdef COMMON_MB_POOL + call_count++ ; + if (call_count == 1) { + return EXT_VIRT_MEM; + } + else { + return EXT_VIRT_MEM_2; + } +#else + return EXT_VIRT_MEM; +#endif +#else + return 0; +#endif +} + +/* + * BEGIN_MANUAL_ENTRY(mac_drv_init) + * void mac_drv_init(smc) + * + * function DOWNCALL (drvsr.c) + * In this function the hardware module allocates it's + * memory. + * The operating system dependent module should call + * mac_drv_init once, after the adatper is detected. + * END_MANUAL_ENTRY + */ +int mac_drv_init(struct s_smc *smc) +{ + if (sizeof(struct s_smt_fp_rxd) % 16) { + SMT_PANIC(smc,HWM_E0001,HWM_E0001_MSG) ; + } + if (sizeof(struct s_smt_fp_txd) % 16) { + SMT_PANIC(smc,HWM_E0002,HWM_E0002_MSG) ; + } + + /* + * get the required memory for the RxDs and TxDs + */ + if (!(smc->os.hwm.descr_p = (union s_fp_descr volatile *) + mac_drv_get_desc_mem(smc,(u_int) + (RXD_TXD_COUNT+1)*sizeof(struct s_smt_fp_txd)))) { + return 1; /* no space the hwm modul can't work */ + } + + /* + * get the memory for the SMT MBufs + */ +#ifndef MB_OUTSIDE_SMC + smc->os.hwm.mbuf_pool.mb_start=(SMbuf *)(&smc->os.hwm.mbuf_pool.mb[0]) ; +#else +#ifndef COMMON_MB_POOL + if (!(smc->os.hwm.mbuf_pool.mb_start = (SMbuf *) mac_drv_get_space(smc, + MAX_MBUF*sizeof(SMbuf)))) { + return 1; /* no space the hwm modul can't work */ + } +#else + if (!mb_start) { + if (!(mb_start = (SMbuf *) mac_drv_get_space(smc, + MAX_MBUF*sizeof(SMbuf)))) { + return 1; /* no space the hwm modul can't work */ + } + } +#endif +#endif + return 0; +} + +/* + * BEGIN_MANUAL_ENTRY(init_driver_fplus) + * init_driver_fplus(smc) + * + * Sets hardware modul specific values for the mode register 2 + * (e.g. the byte alignment for the received frames, the position of the + * least significant byte etc.) + * END_MANUAL_ENTRY + */ +void init_driver_fplus(struct s_smc *smc) +{ + smc->hw.fp.mdr2init = FM_LSB | FM_BMMODE | FM_ENNPRQ | FM_ENHSRQ | 3 ; + +#ifdef PCI + smc->hw.fp.mdr2init |= FM_CHKPAR | FM_PARITY ; +#endif + smc->hw.fp.mdr3init = FM_MENRQAUNLCK | FM_MENRS ; + +#ifdef USE_CAN_ADDR + /* enable address bit swapping */ + smc->hw.fp.frselreg_init = FM_ENXMTADSWAP | FM_ENRCVADSWAP ; +#endif +} + +static u_long init_descr_ring(struct s_smc *smc, + union s_fp_descr volatile *start, + int count) +{ + int i ; + union s_fp_descr volatile *d1 ; + union s_fp_descr volatile *d2 ; + u_long phys ; + + DB_GEN("descr ring starts at = %x ",(void *)start,0,3) ; + for (i=count-1, d1=start; i ; i--) { + d2 = d1 ; + d1++ ; /* descr is owned by the host */ + d2->r.rxd_rbctrl = cpu_to_le32(BMU_CHECK) ; + d2->r.rxd_next = &d1->r ; + phys = mac_drv_virt2phys(smc,(void *)d1) ; + d2->r.rxd_nrdadr = cpu_to_le32(phys) ; + } + DB_GEN("descr ring ends at = %x ",(void *)d1,0,3) ; + d1->r.rxd_rbctrl = cpu_to_le32(BMU_CHECK) ; + d1->r.rxd_next = &start->r ; + phys = mac_drv_virt2phys(smc,(void *)start) ; + d1->r.rxd_nrdadr = cpu_to_le32(phys) ; + + for (i=count, d1=start; i ; i--) { + DRV_BUF_FLUSH(&d1->r,DDI_DMA_SYNC_FORDEV) ; + d1++; + } + return phys; +} + +static void init_txd_ring(struct s_smc *smc) +{ + struct s_smt_fp_txd volatile *ds ; + struct s_smt_tx_queue *queue ; + u_long phys ; + + /* + * initialize the transmit descriptors + */ + ds = (struct s_smt_fp_txd volatile *) ((char *)smc->os.hwm.descr_p + + SMT_R1_RXD_COUNT*sizeof(struct s_smt_fp_rxd)) ; + queue = smc->hw.fp.tx[QUEUE_A0] ; + DB_GEN("Init async TxD ring, %d TxDs ",HWM_ASYNC_TXD_COUNT,0,3) ; + (void)init_descr_ring(smc,(union s_fp_descr volatile *)ds, + HWM_ASYNC_TXD_COUNT) ; + phys = le32_to_cpu(ds->txd_ntdadr) ; + ds++ ; + queue->tx_curr_put = queue->tx_curr_get = ds ; + ds-- ; + queue->tx_free = HWM_ASYNC_TXD_COUNT ; + queue->tx_used = 0 ; + outpd(ADDR(B5_XA_DA),phys) ; + + ds = (struct s_smt_fp_txd volatile *) ((char *)ds + + HWM_ASYNC_TXD_COUNT*sizeof(struct s_smt_fp_txd)) ; + queue = smc->hw.fp.tx[QUEUE_S] ; + DB_GEN("Init sync TxD ring, %d TxDs ",HWM_SYNC_TXD_COUNT,0,3) ; + (void)init_descr_ring(smc,(union s_fp_descr volatile *)ds, + HWM_SYNC_TXD_COUNT) ; + phys = le32_to_cpu(ds->txd_ntdadr) ; + ds++ ; + queue->tx_curr_put = queue->tx_curr_get = ds ; + queue->tx_free = HWM_SYNC_TXD_COUNT ; + queue->tx_used = 0 ; + outpd(ADDR(B5_XS_DA),phys) ; +} + +static void init_rxd_ring(struct s_smc *smc) +{ + struct s_smt_fp_rxd volatile *ds ; + struct s_smt_rx_queue *queue ; + u_long phys ; + + /* + * initialize the receive descriptors + */ + ds = (struct s_smt_fp_rxd volatile *) smc->os.hwm.descr_p ; + queue = smc->hw.fp.rx[QUEUE_R1] ; + DB_GEN("Init RxD ring, %d RxDs ",SMT_R1_RXD_COUNT,0,3) ; + (void)init_descr_ring(smc,(union s_fp_descr volatile *)ds, + SMT_R1_RXD_COUNT) ; + phys = le32_to_cpu(ds->rxd_nrdadr) ; + ds++ ; + queue->rx_curr_put = queue->rx_curr_get = ds ; + queue->rx_free = SMT_R1_RXD_COUNT ; + queue->rx_used = 0 ; + outpd(ADDR(B4_R1_DA),phys) ; +} + +/* + * BEGIN_MANUAL_ENTRY(init_fddi_driver) + * void init_fddi_driver(smc,mac_addr) + * + * initializes the driver and it's variables + * + * END_MANUAL_ENTRY + */ +void init_fddi_driver(struct s_smc *smc, u_char *mac_addr) +{ + SMbuf *mb ; + int i ; + + init_board(smc,mac_addr) ; + (void)init_fplus(smc) ; + + /* + * initialize the SMbufs for the SMT + */ +#ifndef COMMON_MB_POOL + mb = smc->os.hwm.mbuf_pool.mb_start ; + smc->os.hwm.mbuf_pool.mb_free = (SMbuf *)NULL ; + for (i = 0; i < MAX_MBUF; i++) { + mb->sm_use_count = 1 ; + smt_free_mbuf(smc,mb) ; + mb++ ; + } +#else + mb = mb_start ; + if (!mb_init) { + mb_free = 0 ; + for (i = 0; i < MAX_MBUF; i++) { + mb->sm_use_count = 1 ; + smt_free_mbuf(smc,mb) ; + mb++ ; + } + mb_init = TRUE ; + } +#endif + + /* + * initialize the other variables + */ + smc->os.hwm.llc_rx_pipe = smc->os.hwm.llc_rx_tail = (SMbuf *)NULL ; + smc->os.hwm.txd_tx_pipe = smc->os.hwm.txd_tx_tail = NULL ; + smc->os.hwm.pass_SMT = smc->os.hwm.pass_NSA = smc->os.hwm.pass_DB = 0 ; + smc->os.hwm.pass_llc_promisc = TRUE ; + smc->os.hwm.queued_rx_frames = smc->os.hwm.queued_txd_mb = 0 ; + smc->os.hwm.detec_count = 0 ; + smc->os.hwm.rx_break = 0 ; + smc->os.hwm.rx_len_error = 0 ; + smc->os.hwm.isr_flag = FALSE ; + + /* + * make sure that the start pointer is 16 byte aligned + */ + i = 16 - ((long)smc->os.hwm.descr_p & 0xf) ; + if (i != 16) { + DB_GEN("i = %d",i,0,3) ; + smc->os.hwm.descr_p = (union s_fp_descr volatile *) + ((char *)smc->os.hwm.descr_p+i) ; + } + DB_GEN("pt to descr area = %x",(void *)smc->os.hwm.descr_p,0,3) ; + + init_txd_ring(smc) ; + init_rxd_ring(smc) ; + mac_drv_fill_rxd(smc) ; + + init_plc(smc) ; +} + + +SMbuf *smt_get_mbuf(struct s_smc *smc) +{ + register SMbuf *mb ; + +#ifndef COMMON_MB_POOL + mb = smc->os.hwm.mbuf_pool.mb_free ; +#else + mb = mb_free ; +#endif + if (mb) { +#ifndef COMMON_MB_POOL + smc->os.hwm.mbuf_pool.mb_free = mb->sm_next ; +#else + mb_free = mb->sm_next ; +#endif + mb->sm_off = 8 ; + mb->sm_use_count = 1 ; + } + DB_GEN("get SMbuf: mb = %x",(void *)mb,0,3) ; + return mb; /* May be NULL */ +} + +void smt_free_mbuf(struct s_smc *smc, SMbuf *mb) +{ + + if (mb) { + mb->sm_use_count-- ; + DB_GEN("free_mbuf: sm_use_count = %d",mb->sm_use_count,0,3) ; + /* + * If the use_count is != zero the MBuf is queued + * more than once and must not queued into the + * free MBuf queue + */ + if (!mb->sm_use_count) { + DB_GEN("free SMbuf: mb = %x",(void *)mb,0,3) ; +#ifndef COMMON_MB_POOL + mb->sm_next = smc->os.hwm.mbuf_pool.mb_free ; + smc->os.hwm.mbuf_pool.mb_free = mb ; +#else + mb->sm_next = mb_free ; + mb_free = mb ; +#endif + } + } + else + SMT_PANIC(smc,HWM_E0003,HWM_E0003_MSG) ; +} + + +/* + * BEGIN_MANUAL_ENTRY(mac_drv_repair_descr) + * void mac_drv_repair_descr(smc) + * + * function called from SMT (HWM / hwmtm.c) + * The BMU is idle when this function is called. + * Mac_drv_repair_descr sets up the physical address + * for all receive and transmit queues where the BMU + * should continue. + * It may be that the BMU was reseted during a fragmented + * transfer. In this case there are some fragments which will + * never completed by the BMU. The OWN bit of this fragments + * must be switched to be owned by the host. + * + * Give a start command to the receive BMU. + * Start the transmit BMUs if transmit frames pending. + * + * END_MANUAL_ENTRY + */ +void mac_drv_repair_descr(struct s_smc *smc) +{ + u_long phys ; + + if (smc->hw.hw_state != STOPPED) { + SK_BREAK() ; + SMT_PANIC(smc,HWM_E0013,HWM_E0013_MSG) ; + return ; + } + + /* + * repair tx queues: don't start + */ + phys = repair_txd_ring(smc,smc->hw.fp.tx[QUEUE_A0]) ; + outpd(ADDR(B5_XA_DA),phys) ; + if (smc->hw.fp.tx_q[QUEUE_A0].tx_used) { + outpd(ADDR(B0_XA_CSR),CSR_START) ; + } + phys = repair_txd_ring(smc,smc->hw.fp.tx[QUEUE_S]) ; + outpd(ADDR(B5_XS_DA),phys) ; + if (smc->hw.fp.tx_q[QUEUE_S].tx_used) { + outpd(ADDR(B0_XS_CSR),CSR_START) ; + } + + /* + * repair rx queues + */ + phys = repair_rxd_ring(smc,smc->hw.fp.rx[QUEUE_R1]) ; + outpd(ADDR(B4_R1_DA),phys) ; + outpd(ADDR(B0_R1_CSR),CSR_START) ; +} + +static u_long repair_txd_ring(struct s_smc *smc, struct s_smt_tx_queue *queue) +{ + int i ; + int tx_used ; + u_long phys ; + u_long tbctrl ; + struct s_smt_fp_txd volatile *t ; + + SK_UNUSED(smc) ; + + t = queue->tx_curr_get ; + tx_used = queue->tx_used ; + for (i = tx_used+queue->tx_free-1 ; i ; i-- ) { + t = t->txd_next ; + } + phys = le32_to_cpu(t->txd_ntdadr) ; + + t = queue->tx_curr_get ; + while (tx_used) { + DRV_BUF_FLUSH(t,DDI_DMA_SYNC_FORCPU) ; + tbctrl = le32_to_cpu(t->txd_tbctrl) ; + + if (tbctrl & BMU_OWN) { + if (tbctrl & BMU_STF) { + break ; /* exit the loop */ + } + else { + /* + * repair the descriptor + */ + t->txd_tbctrl &= ~cpu_to_le32(BMU_OWN) ; + } + } + phys = le32_to_cpu(t->txd_ntdadr) ; + DRV_BUF_FLUSH(t,DDI_DMA_SYNC_FORDEV) ; + t = t->txd_next ; + tx_used-- ; + } + return phys; +} + +/* + * Repairs the receive descriptor ring and returns the physical address + * where the BMU should continue working. + * + * o The physical address where the BMU was stopped has to be + * determined. This is the next RxD after rx_curr_get with an OWN + * bit set. + * o The BMU should start working at beginning of the next frame. + * RxDs with an OWN bit set but with a reset STF bit should be + * skipped and owned by the driver (OWN = 0). + */ +static u_long repair_rxd_ring(struct s_smc *smc, struct s_smt_rx_queue *queue) +{ + int i ; + int rx_used ; + u_long phys ; + u_long rbctrl ; + struct s_smt_fp_rxd volatile *r ; + + SK_UNUSED(smc) ; + + r = queue->rx_curr_get ; + rx_used = queue->rx_used ; + for (i = SMT_R1_RXD_COUNT-1 ; i ; i-- ) { + r = r->rxd_next ; + } + phys = le32_to_cpu(r->rxd_nrdadr) ; + + r = queue->rx_curr_get ; + while (rx_used) { + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORCPU) ; + rbctrl = le32_to_cpu(r->rxd_rbctrl) ; + + if (rbctrl & BMU_OWN) { + if (rbctrl & BMU_STF) { + break ; /* exit the loop */ + } + else { + /* + * repair the descriptor + */ + r->rxd_rbctrl &= ~cpu_to_le32(BMU_OWN) ; + } + } + phys = le32_to_cpu(r->rxd_nrdadr) ; + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORDEV) ; + r = r->rxd_next ; + rx_used-- ; + } + return phys; +} + + +/* + ------------------------------------------------------------- + INTERRUPT SERVICE ROUTINE: + ------------------------------------------------------------- +*/ + +/* + * BEGIN_MANUAL_ENTRY(fddi_isr) + * void fddi_isr(smc) + * + * function DOWNCALL (drvsr.c) + * interrupt service routine, handles the interrupt requests + * generated by the FDDI adapter. + * + * NOTE: The operating system dependent module must guarantee that the + * interrupts of the adapter are disabled when it calls fddi_isr. + * + * About the USE_BREAK_ISR mechanismn: + * + * The main requirement of this mechanismn is to force an timer IRQ when + * leaving process_receive() with leave_isr set. process_receive() may + * be called at any time from anywhere! + * To be sure we don't miss such event we set 'force_irq' per default. + * We have to force and Timer IRQ if 'smc->os.hwm.leave_isr' AND + * 'force_irq' are set. 'force_irq' may be reset if a receive complete + * IRQ is pending. + * + * END_MANUAL_ENTRY + */ +void fddi_isr(struct s_smc *smc) +{ + u_long is ; /* ISR source */ + u_short stu, stl ; + SMbuf *mb ; + +#ifdef USE_BREAK_ISR + int force_irq ; +#endif + +#ifdef ODI2 + if (smc->os.hwm.rx_break) { + mac_drv_fill_rxd(smc) ; + if (smc->hw.fp.rx_q[QUEUE_R1].rx_used > 0) { + smc->os.hwm.rx_break = 0 ; + process_receive(smc) ; + } + else { + smc->os.hwm.detec_count = 0 ; + smt_force_irq(smc) ; + } + } +#endif + smc->os.hwm.isr_flag = TRUE ; + +#ifdef USE_BREAK_ISR + force_irq = TRUE ; + if (smc->os.hwm.leave_isr) { + smc->os.hwm.leave_isr = FALSE ; + process_receive(smc) ; + } +#endif + + while ((is = GET_ISR() & ISR_MASK)) { + NDD_TRACE("CH0B",is,0,0) ; + DB_GEN("ISA = 0x%x",is,0,7) ; + + if (is & IMASK_SLOW) { + NDD_TRACE("CH1b",is,0,0) ; + if (is & IS_PLINT1) { /* PLC1 */ + plc1_irq(smc) ; + } + if (is & IS_PLINT2) { /* PLC2 */ + plc2_irq(smc) ; + } + if (is & IS_MINTR1) { /* FORMAC+ STU1(U/L) */ + stu = inpw(FM_A(FM_ST1U)) ; + stl = inpw(FM_A(FM_ST1L)) ; + DB_GEN("Slow transmit complete",0,0,6) ; + mac1_irq(smc,stu,stl) ; + } + if (is & IS_MINTR2) { /* FORMAC+ STU2(U/L) */ + stu= inpw(FM_A(FM_ST2U)) ; + stl= inpw(FM_A(FM_ST2L)) ; + DB_GEN("Slow receive complete",0,0,6) ; + DB_GEN("stl = %x : stu = %x",stl,stu,7) ; + mac2_irq(smc,stu,stl) ; + } + if (is & IS_MINTR3) { /* FORMAC+ STU3(U/L) */ + stu= inpw(FM_A(FM_ST3U)) ; + stl= inpw(FM_A(FM_ST3L)) ; + DB_GEN("FORMAC Mode Register 3",0,0,6) ; + mac3_irq(smc,stu,stl) ; + } + if (is & IS_TIMINT) { /* Timer 82C54-2 */ + timer_irq(smc) ; +#ifdef NDIS_OS2 + force_irq_pending = 0 ; +#endif + /* + * out of RxD detection + */ + if (++smc->os.hwm.detec_count > 4) { + /* + * check out of RxD condition + */ + process_receive(smc) ; + } + } + if (is & IS_TOKEN) { /* Restricted Token Monitor */ + rtm_irq(smc) ; + } + if (is & IS_R1_P) { /* Parity error rx queue 1 */ + /* clear IRQ */ + outpd(ADDR(B4_R1_CSR),CSR_IRQ_CL_P) ; + SMT_PANIC(smc,HWM_E0004,HWM_E0004_MSG) ; + } + if (is & IS_R1_C) { /* Encoding error rx queue 1 */ + /* clear IRQ */ + outpd(ADDR(B4_R1_CSR),CSR_IRQ_CL_C) ; + SMT_PANIC(smc,HWM_E0005,HWM_E0005_MSG) ; + } + if (is & IS_XA_C) { /* Encoding error async tx q */ + /* clear IRQ */ + outpd(ADDR(B5_XA_CSR),CSR_IRQ_CL_C) ; + SMT_PANIC(smc,HWM_E0006,HWM_E0006_MSG) ; + } + if (is & IS_XS_C) { /* Encoding error sync tx q */ + /* clear IRQ */ + outpd(ADDR(B5_XS_CSR),CSR_IRQ_CL_C) ; + SMT_PANIC(smc,HWM_E0007,HWM_E0007_MSG) ; + } + } + + /* + * Fast Tx complete Async/Sync Queue (BMU service) + */ + if (is & (IS_XS_F|IS_XA_F)) { + DB_GEN("Fast tx complete queue",0,0,6) ; + /* + * clear IRQ, Note: no IRQ is lost, because + * we always service both queues + */ + outpd(ADDR(B5_XS_CSR),CSR_IRQ_CL_F) ; + outpd(ADDR(B5_XA_CSR),CSR_IRQ_CL_F) ; + mac_drv_clear_txd(smc) ; + llc_restart_tx(smc) ; + } + + /* + * Fast Rx Complete (BMU service) + */ + if (is & IS_R1_F) { + DB_GEN("Fast receive complete",0,0,6) ; + /* clear IRQ */ +#ifndef USE_BREAK_ISR + outpd(ADDR(B4_R1_CSR),CSR_IRQ_CL_F) ; + process_receive(smc) ; +#else + process_receive(smc) ; + if (smc->os.hwm.leave_isr) { + force_irq = FALSE ; + } else { + outpd(ADDR(B4_R1_CSR),CSR_IRQ_CL_F) ; + process_receive(smc) ; + } +#endif + } + +#ifndef NDIS_OS2 + while ((mb = get_llc_rx(smc))) { + smt_to_llc(smc,mb) ; + } +#else + if (offDepth) + post_proc() ; + + while (!offDepth && (mb = get_llc_rx(smc))) { + smt_to_llc(smc,mb) ; + } + + if (!offDepth && smc->os.hwm.rx_break) { + process_receive(smc) ; + } +#endif + if (smc->q.ev_get != smc->q.ev_put) { + NDD_TRACE("CH2a",0,0,0) ; + ev_dispatcher(smc) ; + } +#ifdef NDIS_OS2 + post_proc() ; + if (offDepth) { /* leave fddi_isr because */ + break ; /* indications not allowed */ + } +#endif +#ifdef USE_BREAK_ISR + if (smc->os.hwm.leave_isr) { + break ; /* leave fddi_isr */ + } +#endif + + /* NOTE: when the isr is left, no rx is pending */ + } /* end of interrupt source polling loop */ + +#ifdef USE_BREAK_ISR + if (smc->os.hwm.leave_isr && force_irq) { + smt_force_irq(smc) ; + } +#endif + smc->os.hwm.isr_flag = FALSE ; + NDD_TRACE("CH0E",0,0,0) ; +} + + +/* + ------------------------------------------------------------- + RECEIVE FUNCTIONS: + ------------------------------------------------------------- +*/ + +#ifndef NDIS_OS2 +/* + * BEGIN_MANUAL_ENTRY(mac_drv_rx_mode) + * void mac_drv_rx_mode(smc,mode) + * + * function DOWNCALL (fplus.c) + * Corresponding to the parameter mode, the operating system + * dependent module can activate several receive modes. + * + * para mode = 1: RX_ENABLE_ALLMULTI enable all multicasts + * = 2: RX_DISABLE_ALLMULTI disable "enable all multicasts" + * = 3: RX_ENABLE_PROMISC enable promiscuous + * = 4: RX_DISABLE_PROMISC disable promiscuous + * = 5: RX_ENABLE_NSA enable rec. of all NSA frames + * (disabled after 'driver reset' & 'set station address') + * = 6: RX_DISABLE_NSA disable rec. of all NSA frames + * + * = 21: RX_ENABLE_PASS_SMT ( see description ) + * = 22: RX_DISABLE_PASS_SMT ( " " ) + * = 23: RX_ENABLE_PASS_NSA ( " " ) + * = 24: RX_DISABLE_PASS_NSA ( " " ) + * = 25: RX_ENABLE_PASS_DB ( " " ) + * = 26: RX_DISABLE_PASS_DB ( " " ) + * = 27: RX_DISABLE_PASS_ALL ( " " ) + * = 28: RX_DISABLE_LLC_PROMISC ( " " ) + * = 29: RX_ENABLE_LLC_PROMISC ( " " ) + * + * + * RX_ENABLE_PASS_SMT / RX_DISABLE_PASS_SMT + * + * If the operating system dependent module activates the + * mode RX_ENABLE_PASS_SMT, the hardware module + * duplicates all SMT frames with the frame control + * FC_SMT_INFO and passes them to the LLC receive channel + * by calling mac_drv_rx_init. + * The SMT Frames which are sent by the local SMT and the NSA + * frames whose A- and C-Indicator is not set are also duplicated + * and passed. + * The receive mode RX_DISABLE_PASS_SMT disables the passing + * of SMT frames. + * + * RX_ENABLE_PASS_NSA / RX_DISABLE_PASS_NSA + * + * If the operating system dependent module activates the + * mode RX_ENABLE_PASS_NSA, the hardware module + * duplicates all NSA frames with frame control FC_SMT_NSA + * and a set A-Indicator and passed them to the LLC + * receive channel by calling mac_drv_rx_init. + * All NSA Frames which are sent by the local SMT + * are also duplicated and passed. + * The receive mode RX_DISABLE_PASS_NSA disables the passing + * of NSA frames with the A- or C-Indicator set. + * + * NOTE: For fear that the hardware module receives NSA frames with + * a reset A-Indicator, the operating system dependent module + * has to call mac_drv_rx_mode with the mode RX_ENABLE_NSA + * before activate the RX_ENABLE_PASS_NSA mode and after every + * 'driver reset' and 'set station address'. + * + * RX_ENABLE_PASS_DB / RX_DISABLE_PASS_DB + * + * If the operating system dependent module activates the + * mode RX_ENABLE_PASS_DB, direct BEACON frames + * (FC_BEACON frame control) are passed to the LLC receive + * channel by mac_drv_rx_init. + * The receive mode RX_DISABLE_PASS_DB disables the passing + * of direct BEACON frames. + * + * RX_DISABLE_PASS_ALL + * + * Disables all special receives modes. It is equal to + * call mac_drv_set_rx_mode successively with the + * parameters RX_DISABLE_NSA, RX_DISABLE_PASS_SMT, + * RX_DISABLE_PASS_NSA and RX_DISABLE_PASS_DB. + * + * RX_ENABLE_LLC_PROMISC + * + * (default) all received LLC frames and all SMT/NSA/DBEACON + * frames depending on the attitude of the flags + * PASS_SMT/PASS_NSA/PASS_DBEACON will be delivered to the + * LLC layer + * + * RX_DISABLE_LLC_PROMISC + * + * all received SMT/NSA/DBEACON frames depending on the + * attitude of the flags PASS_SMT/PASS_NSA/PASS_DBEACON + * will be delivered to the LLC layer. + * all received LLC frames with a directed address, Multicast + * or Broadcast address will be delivered to the LLC + * layer too. + * + * END_MANUAL_ENTRY + */ +void mac_drv_rx_mode(struct s_smc *smc, int mode) +{ + switch(mode) { + case RX_ENABLE_PASS_SMT: + smc->os.hwm.pass_SMT = TRUE ; + break ; + case RX_DISABLE_PASS_SMT: + smc->os.hwm.pass_SMT = FALSE ; + break ; + case RX_ENABLE_PASS_NSA: + smc->os.hwm.pass_NSA = TRUE ; + break ; + case RX_DISABLE_PASS_NSA: + smc->os.hwm.pass_NSA = FALSE ; + break ; + case RX_ENABLE_PASS_DB: + smc->os.hwm.pass_DB = TRUE ; + break ; + case RX_DISABLE_PASS_DB: + smc->os.hwm.pass_DB = FALSE ; + break ; + case RX_DISABLE_PASS_ALL: + smc->os.hwm.pass_SMT = smc->os.hwm.pass_NSA = FALSE ; + smc->os.hwm.pass_DB = FALSE ; + smc->os.hwm.pass_llc_promisc = TRUE ; + mac_set_rx_mode(smc,RX_DISABLE_NSA) ; + break ; + case RX_DISABLE_LLC_PROMISC: + smc->os.hwm.pass_llc_promisc = FALSE ; + break ; + case RX_ENABLE_LLC_PROMISC: + smc->os.hwm.pass_llc_promisc = TRUE ; + break ; + case RX_ENABLE_ALLMULTI: + case RX_DISABLE_ALLMULTI: + case RX_ENABLE_PROMISC: + case RX_DISABLE_PROMISC: + case RX_ENABLE_NSA: + case RX_DISABLE_NSA: + default: + mac_set_rx_mode(smc,mode) ; + break ; + } +} +#endif /* ifndef NDIS_OS2 */ + +/* + * process receive queue + */ +void process_receive(struct s_smc *smc) +{ + int i ; + int n ; + int frag_count ; /* number of RxDs of the curr rx buf */ + int used_frags ; /* number of RxDs of the curr frame */ + struct s_smt_rx_queue *queue ; /* points to the queue ctl struct */ + struct s_smt_fp_rxd volatile *r ; /* rxd pointer */ + struct s_smt_fp_rxd volatile *rxd ; /* first rxd of rx frame */ + u_long rbctrl ; /* receive buffer control word */ + u_long rfsw ; /* receive frame status word */ + u_short rx_used ; + u_char far *virt ; + char far *data ; + SMbuf *mb ; + u_char fc ; /* Frame control */ + int len ; /* Frame length */ + + smc->os.hwm.detec_count = 0 ; + queue = smc->hw.fp.rx[QUEUE_R1] ; + NDD_TRACE("RHxB",0,0,0) ; + for ( ; ; ) { + r = queue->rx_curr_get ; + rx_used = queue->rx_used ; + frag_count = 0 ; + +#ifdef USE_BREAK_ISR + if (smc->os.hwm.leave_isr) { + goto rx_end ; + } +#endif +#ifdef NDIS_OS2 + if (offDepth) { + smc->os.hwm.rx_break = 1 ; + goto rx_end ; + } + smc->os.hwm.rx_break = 0 ; +#endif +#ifdef ODI2 + if (smc->os.hwm.rx_break) { + goto rx_end ; + } +#endif + n = 0 ; + do { + DB_RX("Check RxD %x for OWN and EOF",(void *)r,0,5) ; + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORCPU) ; + rbctrl = le32_to_cpu(CR_READ(r->rxd_rbctrl)); + + if (rbctrl & BMU_OWN) { + NDD_TRACE("RHxE",r,rfsw,rbctrl) ; + DB_RX("End of RxDs",0,0,4) ; + goto rx_end ; + } + /* + * out of RxD detection + */ + if (!rx_used) { + SK_BREAK() ; + SMT_PANIC(smc,HWM_E0009,HWM_E0009_MSG) ; + /* Either we don't have an RxD or all + * RxDs are filled. Therefore it's allowed + * for to set the STOPPED flag */ + smc->hw.hw_state = STOPPED ; + mac_drv_clear_rx_queue(smc) ; + smc->hw.hw_state = STARTED ; + mac_drv_fill_rxd(smc) ; + smc->os.hwm.detec_count = 0 ; + goto rx_end ; + } + rfsw = le32_to_cpu(r->rxd_rfsw) ; + if ((rbctrl & BMU_STF) != ((rbctrl & BMU_ST_BUF) <<5)) { + /* + * The BMU_STF bit is deleted, 1 frame is + * placed into more than 1 rx buffer + * + * skip frame by setting the rx len to 0 + * + * if fragment count == 0 + * The missing STF bit belongs to the + * current frame, search for the + * EOF bit to complete the frame + * else + * the fragment belongs to the next frame, + * exit the loop and process the frame + */ + SK_BREAK() ; + rfsw = 0 ; + if (frag_count) { + break ; + } + } + n += rbctrl & 0xffff ; + r = r->rxd_next ; + frag_count++ ; + rx_used-- ; + } while (!(rbctrl & BMU_EOF)) ; + used_frags = frag_count ; + DB_RX("EOF set in RxD, used_frags = %d ",used_frags,0,5) ; + + /* may be next 2 DRV_BUF_FLUSH() can be skipped, because */ + /* BMU_ST_BUF will not be changed by the ASIC */ + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORCPU) ; + while (rx_used && !(r->rxd_rbctrl & cpu_to_le32(BMU_ST_BUF))) { + DB_RX("Check STF bit in %x",(void *)r,0,5) ; + r = r->rxd_next ; + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORCPU) ; + frag_count++ ; + rx_used-- ; + } + DB_RX("STF bit found",0,0,5) ; + + /* + * The received frame is finished for the process receive + */ + rxd = queue->rx_curr_get ; + queue->rx_curr_get = r ; + queue->rx_free += frag_count ; + queue->rx_used = rx_used ; + + /* + * ASIC Errata no. 7 (STF - Bit Bug) + */ + rxd->rxd_rbctrl &= cpu_to_le32(~BMU_STF) ; + + for (r=rxd, i=frag_count ; i ; r=r->rxd_next, i--){ + DB_RX("dma_complete for RxD %x",(void *)r,0,5) ; + dma_complete(smc,(union s_fp_descr volatile *)r,DMA_WR); + } + smc->hw.fp.err_stats.err_valid++ ; + smc->mib.m[MAC0].fddiMACCopied_Ct++ ; + + /* the length of the data including the FC */ + len = (rfsw & RD_LENGTH) - 4 ; + + DB_RX("frame length = %d",len,0,4) ; + /* + * check the frame_length and all error flags + */ + if (rfsw & (RX_MSRABT|RX_FS_E|RX_FS_CRC|RX_FS_IMPL)){ + if (rfsw & RD_S_MSRABT) { + DB_RX("Frame aborted by the FORMAC",0,0,2) ; + smc->hw.fp.err_stats.err_abort++ ; + } + /* + * check frame status + */ + if (rfsw & RD_S_SEAC2) { + DB_RX("E-Indicator set",0,0,2) ; + smc->hw.fp.err_stats.err_e_indicator++ ; + } + if (rfsw & RD_S_SFRMERR) { + DB_RX("CRC error",0,0,2) ; + smc->hw.fp.err_stats.err_crc++ ; + } + if (rfsw & RX_FS_IMPL) { + DB_RX("Implementer frame",0,0,2) ; + smc->hw.fp.err_stats.err_imp_frame++ ; + } + goto abort_frame ; + } + if (len > FDDI_RAW_MTU-4) { + DB_RX("Frame too long error",0,0,2) ; + smc->hw.fp.err_stats.err_too_long++ ; + goto abort_frame ; + } + /* + * SUPERNET 3 Bug: FORMAC delivers status words + * of aborded frames to the BMU + */ + if (len <= 4) { + DB_RX("Frame length = 0",0,0,2) ; + goto abort_frame ; + } + + if (len != (n-4)) { + DB_RX("BMU: rx len differs: [%d:%d]",len,n,4); + smc->os.hwm.rx_len_error++ ; + goto abort_frame ; + } + + /* + * Check SA == MA + */ + virt = (u_char far *) rxd->rxd_virt ; + DB_RX("FC = %x",*virt,0,2) ; + if (virt[12] == MA[5] && + virt[11] == MA[4] && + virt[10] == MA[3] && + virt[9] == MA[2] && + virt[8] == MA[1] && + (virt[7] & ~GROUP_ADDR_BIT) == MA[0]) { + goto abort_frame ; + } + + /* + * test if LLC frame + */ + if (rfsw & RX_FS_LLC) { + /* + * if pass_llc_promisc is disable + * if DA != Multicast or Broadcast or DA!=MA + * abort the frame + */ + if (!smc->os.hwm.pass_llc_promisc) { + if(!(virt[1] & GROUP_ADDR_BIT)) { + if (virt[6] != MA[5] || + virt[5] != MA[4] || + virt[4] != MA[3] || + virt[3] != MA[2] || + virt[2] != MA[1] || + virt[1] != MA[0]) { + DB_RX("DA != MA and not multi- or broadcast",0,0,2) ; + goto abort_frame ; + } + } + } + + /* + * LLC frame received + */ + DB_RX("LLC - receive",0,0,4) ; + mac_drv_rx_complete(smc,rxd,frag_count,len) ; + } + else { + if (!(mb = smt_get_mbuf(smc))) { + smc->hw.fp.err_stats.err_no_buf++ ; + DB_RX("No SMbuf; receive terminated",0,0,4) ; + goto abort_frame ; + } + data = smtod(mb,char *) - 1 ; + + /* + * copy the frame into a SMT_MBuf + */ +#ifdef USE_OS_CPY + hwm_cpy_rxd2mb(rxd,data,len) ; +#else + for (r=rxd, i=used_frags ; i ; r=r->rxd_next, i--){ + n = le32_to_cpu(r->rxd_rbctrl) & RD_LENGTH ; + DB_RX("cp SMT frame to mb: len = %d",n,0,6) ; + memcpy(data,r->rxd_virt,n) ; + data += n ; + } + data = smtod(mb,char *) - 1 ; +#endif + fc = *(char *)mb->sm_data = *data ; + mb->sm_len = len - 1 ; /* len - fc */ + data++ ; + + /* + * SMT frame received + */ + switch(fc) { + case FC_SMT_INFO : + smc->hw.fp.err_stats.err_smt_frame++ ; + DB_RX("SMT frame received ",0,0,5) ; + + if (smc->os.hwm.pass_SMT) { + DB_RX("pass SMT frame ",0,0,5) ; + mac_drv_rx_complete(smc, rxd, + frag_count,len) ; + } + else { + DB_RX("requeue RxD",0,0,5) ; + mac_drv_requeue_rxd(smc,rxd,frag_count); + } + + smt_received_pack(smc,mb,(int)(rfsw>>25)) ; + break ; + case FC_SMT_NSA : + smc->hw.fp.err_stats.err_smt_frame++ ; + DB_RX("SMT frame received ",0,0,5) ; + + /* if pass_NSA set pass the NSA frame or */ + /* pass_SMT set and the A-Indicator */ + /* is not set, pass the NSA frame */ + if (smc->os.hwm.pass_NSA || + (smc->os.hwm.pass_SMT && + !(rfsw & A_INDIC))) { + DB_RX("pass SMT frame ",0,0,5) ; + mac_drv_rx_complete(smc, rxd, + frag_count,len) ; + } + else { + DB_RX("requeue RxD",0,0,5) ; + mac_drv_requeue_rxd(smc,rxd,frag_count); + } + + smt_received_pack(smc,mb,(int)(rfsw>>25)) ; + break ; + case FC_BEACON : + if (smc->os.hwm.pass_DB) { + DB_RX("pass DB frame ",0,0,5) ; + mac_drv_rx_complete(smc, rxd, + frag_count,len) ; + } + else { + DB_RX("requeue RxD",0,0,5) ; + mac_drv_requeue_rxd(smc,rxd,frag_count); + } + smt_free_mbuf(smc,mb) ; + break ; + default : + /* + * unknown FC abord the frame + */ + DB_RX("unknown FC error",0,0,2) ; + smt_free_mbuf(smc,mb) ; + DB_RX("requeue RxD",0,0,5) ; + mac_drv_requeue_rxd(smc,rxd,frag_count) ; + if ((fc & 0xf0) == FC_MAC) + smc->hw.fp.err_stats.err_mac_frame++ ; + else + smc->hw.fp.err_stats.err_imp_frame++ ; + + break ; + } + } + + DB_RX("next RxD is %x ",queue->rx_curr_get,0,3) ; + NDD_TRACE("RHx1",queue->rx_curr_get,0,0) ; + + continue ; + /*--------------------------------------------------------------------*/ +abort_frame: + DB_RX("requeue RxD",0,0,5) ; + mac_drv_requeue_rxd(smc,rxd,frag_count) ; + + DB_RX("next RxD is %x ",queue->rx_curr_get,0,3) ; + NDD_TRACE("RHx2",queue->rx_curr_get,0,0) ; + } +rx_end: +#ifdef ALL_RX_COMPLETE + mac_drv_all_receives_complete(smc) ; +#endif + return ; /* lint bug: needs return detect end of function */ +} + +static void smt_to_llc(struct s_smc *smc, SMbuf *mb) +{ + u_char fc ; + + DB_RX("send a queued frame to the llc layer",0,0,4) ; + smc->os.hwm.r.len = mb->sm_len ; + smc->os.hwm.r.mb_pos = smtod(mb,char *) ; + fc = *smc->os.hwm.r.mb_pos ; + (void)mac_drv_rx_init(smc,(int)mb->sm_len,(int)fc, + smc->os.hwm.r.mb_pos,(int)mb->sm_len) ; + smt_free_mbuf(smc,mb) ; +} + +/* + * BEGIN_MANUAL_ENTRY(hwm_rx_frag) + * void hwm_rx_frag(smc,virt,phys,len,frame_status) + * + * function MACRO (hardware module, hwmtm.h) + * This function calls dma_master for preparing the + * system hardware for the DMA transfer and initializes + * the current RxD with the length and the physical and + * virtual address of the fragment. Furthermore, it sets the + * STF and EOF bits depending on the frame status byte, + * switches the OWN flag of the RxD, so that it is owned by the + * adapter and issues an rx_start. + * + * para virt virtual pointer to the fragment + * len the length of the fragment + * frame_status status of the frame, see design description + * + * NOTE: It is possible to call this function with a fragment length + * of zero. + * + * END_MANUAL_ENTRY + */ +void hwm_rx_frag(struct s_smc *smc, char far *virt, u_long phys, int len, + int frame_status) +{ + struct s_smt_fp_rxd volatile *r ; + __le32 rbctrl; + + NDD_TRACE("RHfB",virt,len,frame_status) ; + DB_RX("hwm_rx_frag: len = %d, frame_status = %x\n",len,frame_status,2) ; + r = smc->hw.fp.rx_q[QUEUE_R1].rx_curr_put ; + r->rxd_virt = virt ; + r->rxd_rbadr = cpu_to_le32(phys) ; + rbctrl = cpu_to_le32( (((__u32)frame_status & + (FIRST_FRAG|LAST_FRAG))<<26) | + (((u_long) frame_status & FIRST_FRAG) << 21) | + BMU_OWN | BMU_CHECK | BMU_EN_IRQ_EOF | len) ; + r->rxd_rbctrl = rbctrl ; + + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORDEV) ; + outpd(ADDR(B0_R1_CSR),CSR_START) ; + smc->hw.fp.rx_q[QUEUE_R1].rx_free-- ; + smc->hw.fp.rx_q[QUEUE_R1].rx_used++ ; + smc->hw.fp.rx_q[QUEUE_R1].rx_curr_put = r->rxd_next ; + NDD_TRACE("RHfE",r,le32_to_cpu(r->rxd_rbadr),0) ; +} + +/* + * BEGINN_MANUAL_ENTRY(mac_drv_clear_rx_queue) + * + * void mac_drv_clear_rx_queue(smc) + * struct s_smc *smc ; + * + * function DOWNCALL (hardware module, hwmtm.c) + * mac_drv_clear_rx_queue is called by the OS-specific module + * after it has issued a card_stop. + * In this case, the frames in the receive queue are obsolete and + * should be removed. For removing mac_drv_clear_rx_queue + * calls dma_master for each RxD and mac_drv_clear_rxd for each + * receive buffer. + * + * NOTE: calling sequence card_stop: + * CLI_FBI(), card_stop(), + * mac_drv_clear_tx_queue(), mac_drv_clear_rx_queue(), + * + * NOTE: The caller is responsible that the BMUs are idle + * when this function is called. + * + * END_MANUAL_ENTRY + */ +void mac_drv_clear_rx_queue(struct s_smc *smc) +{ + struct s_smt_fp_rxd volatile *r ; + struct s_smt_fp_rxd volatile *next_rxd ; + struct s_smt_rx_queue *queue ; + int frag_count ; + int i ; + + if (smc->hw.hw_state != STOPPED) { + SK_BREAK() ; + SMT_PANIC(smc,HWM_E0012,HWM_E0012_MSG) ; + return ; + } + + queue = smc->hw.fp.rx[QUEUE_R1] ; + DB_RX("clear_rx_queue",0,0,5) ; + + /* + * dma_complete and mac_drv_clear_rxd for all RxDs / receive buffers + */ + r = queue->rx_curr_get ; + while (queue->rx_used) { + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORCPU) ; + DB_RX("switch OWN bit of RxD 0x%x ",r,0,5) ; + r->rxd_rbctrl &= ~cpu_to_le32(BMU_OWN) ; + frag_count = 1 ; + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORDEV) ; + r = r->rxd_next ; + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORCPU) ; + while (r != queue->rx_curr_put && + !(r->rxd_rbctrl & cpu_to_le32(BMU_ST_BUF))) { + DB_RX("Check STF bit in %x",(void *)r,0,5) ; + r->rxd_rbctrl &= ~cpu_to_le32(BMU_OWN) ; + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORDEV) ; + r = r->rxd_next ; + DRV_BUF_FLUSH(r,DDI_DMA_SYNC_FORCPU) ; + frag_count++ ; + } + DB_RX("STF bit found",0,0,5) ; + next_rxd = r ; + + for (r=queue->rx_curr_get,i=frag_count; i ; r=r->rxd_next,i--){ + DB_RX("dma_complete for RxD %x",(void *)r,0,5) ; + dma_complete(smc,(union s_fp_descr volatile *)r,DMA_WR); + } + + DB_RX("mac_drv_clear_rxd: RxD %x frag_count %d ", + (void *)queue->rx_curr_get,frag_count,5) ; + mac_drv_clear_rxd(smc,queue->rx_curr_get,frag_count) ; + + queue->rx_curr_get = next_rxd ; + queue->rx_used -= frag_count ; + queue->rx_free += frag_count ; + } +} + + +/* + ------------------------------------------------------------- + SEND FUNCTIONS: + ------------------------------------------------------------- +*/ + +/* + * BEGIN_MANUAL_ENTRY(hwm_tx_init) + * int hwm_tx_init(smc,fc,frag_count,frame_len,frame_status) + * + * function DOWN_CALL (hardware module, hwmtm.c) + * hwm_tx_init checks if the frame can be sent through the + * corresponding send queue. + * + * para fc the frame control. To determine through which + * send queue the frame should be transmitted. + * 0x50 - 0x57: asynchronous LLC frame + * 0xD0 - 0xD7: synchronous LLC frame + * 0x41, 0x4F: SMT frame to the network + * 0x42: SMT frame to the network and to the local SMT + * 0x43: SMT frame to the local SMT + * frag_count count of the fragments for this frame + * frame_len length of the frame + * frame_status status of the frame, the send queue bit is already + * specified + * + * return frame_status + * + * END_MANUAL_ENTRY + */ +int hwm_tx_init(struct s_smc *smc, u_char fc, int frag_count, int frame_len, + int frame_status) +{ + NDD_TRACE("THiB",fc,frag_count,frame_len) ; + smc->os.hwm.tx_p = smc->hw.fp.tx[frame_status & QUEUE_A0] ; + smc->os.hwm.tx_descr = TX_DESCRIPTOR | (((u_long)(frame_len-1)&3)<<27) ; + smc->os.hwm.tx_len = frame_len ; + DB_TX("hwm_tx_init: fc = %x, len = %d",fc,frame_len,3) ; + if ((fc & ~(FC_SYNC_BIT|FC_LLC_PRIOR)) == FC_ASYNC_LLC) { + frame_status |= LAN_TX ; + } + else { + switch (fc) { + case FC_SMT_INFO : + case FC_SMT_NSA : + frame_status |= LAN_TX ; + break ; + case FC_SMT_LOC : + frame_status |= LOC_TX ; + break ; + case FC_SMT_LAN_LOC : + frame_status |= LAN_TX | LOC_TX ; + break ; + default : + SMT_PANIC(smc,HWM_E0010,HWM_E0010_MSG) ; + } + } + if (!smc->hw.mac_ring_is_up) { + frame_status &= ~LAN_TX ; + frame_status |= RING_DOWN ; + DB_TX("Ring is down: terminate LAN_TX",0,0,2) ; + } + if (frag_count > smc->os.hwm.tx_p->tx_free) { +#ifndef NDIS_OS2 + mac_drv_clear_txd(smc) ; + if (frag_count > smc->os.hwm.tx_p->tx_free) { + DB_TX("Out of TxDs, terminate LAN_TX",0,0,2) ; + frame_status &= ~LAN_TX ; + frame_status |= OUT_OF_TXD ; + } +#else + DB_TX("Out of TxDs, terminate LAN_TX",0,0,2) ; + frame_status &= ~LAN_TX ; + frame_status |= OUT_OF_TXD ; +#endif + } + DB_TX("frame_status = %x",frame_status,0,3) ; + NDD_TRACE("THiE",frame_status,smc->os.hwm.tx_p->tx_free,0) ; + return frame_status; +} + +/* + * BEGIN_MANUAL_ENTRY(hwm_tx_frag) + * void hwm_tx_frag(smc,virt,phys,len,frame_status) + * + * function DOWNCALL (hardware module, hwmtm.c) + * If the frame should be sent to the LAN, this function calls + * dma_master, fills the current TxD with the virtual and the + * physical address, sets the STF and EOF bits dependent on + * the frame status, and requests the BMU to start the + * transmit. + * If the frame should be sent to the local SMT, an SMT_MBuf + * is allocated if the FIRST_FRAG bit is set in the frame_status. + * The fragment of the frame is copied into the SMT MBuf. + * The function smt_received_pack is called if the LAST_FRAG + * bit is set in the frame_status word. + * + * para virt virtual pointer to the fragment + * len the length of the fragment + * frame_status status of the frame, see design description + * + * return nothing returned, no parameter is modified + * + * NOTE: It is possible to invoke this macro with a fragment length + * of zero. + * + * END_MANUAL_ENTRY + */ +void hwm_tx_frag(struct s_smc *smc, char far *virt, u_long phys, int len, + int frame_status) +{ + struct s_smt_fp_txd volatile *t ; + struct s_smt_tx_queue *queue ; + __le32 tbctrl ; + + queue = smc->os.hwm.tx_p ; + + NDD_TRACE("THfB",virt,len,frame_status) ; + /* Bug fix: AF / May 31 1999 (#missing) + * snmpinfo problem reported by IBM is caused by invalid + * t-pointer (txd) if LAN_TX is not set but LOC_TX only. + * Set: t = queue->tx_curr_put here ! + */ + t = queue->tx_curr_put ; + + DB_TX("hwm_tx_frag: len = %d, frame_status = %x ",len,frame_status,2) ; + if (frame_status & LAN_TX) { + /* '*t' is already defined */ + DB_TX("LAN_TX: TxD = %x, virt = %x ",t,virt,3) ; + t->txd_virt = virt ; + t->txd_txdscr = cpu_to_le32(smc->os.hwm.tx_descr) ; + t->txd_tbadr = cpu_to_le32(phys) ; + tbctrl = cpu_to_le32((((__u32)frame_status & + (FIRST_FRAG|LAST_FRAG|EN_IRQ_EOF))<< 26) | + BMU_OWN|BMU_CHECK |len) ; + t->txd_tbctrl = tbctrl ; + +#ifndef AIX + DRV_BUF_FLUSH(t,DDI_DMA_SYNC_FORDEV) ; + outpd(queue->tx_bmu_ctl,CSR_START) ; +#else /* ifndef AIX */ + DRV_BUF_FLUSH(t,DDI_DMA_SYNC_FORDEV) ; + if (frame_status & QUEUE_A0) { + outpd(ADDR(B0_XA_CSR),CSR_START) ; + } + else { + outpd(ADDR(B0_XS_CSR),CSR_START) ; + } +#endif + queue->tx_free-- ; + queue->tx_used++ ; + queue->tx_curr_put = t->txd_next ; + if (frame_status & LAST_FRAG) { + smc->mib.m[MAC0].fddiMACTransmit_Ct++ ; + } + } + if (frame_status & LOC_TX) { + DB_TX("LOC_TX: ",0,0,3) ; + if (frame_status & FIRST_FRAG) { + if(!(smc->os.hwm.tx_mb = smt_get_mbuf(smc))) { + smc->hw.fp.err_stats.err_no_buf++ ; + DB_TX("No SMbuf; transmit terminated",0,0,4) ; + } + else { + smc->os.hwm.tx_data = + smtod(smc->os.hwm.tx_mb,char *) - 1 ; +#ifdef USE_OS_CPY +#ifdef PASS_1ST_TXD_2_TX_COMP + hwm_cpy_txd2mb(t,smc->os.hwm.tx_data, + smc->os.hwm.tx_len) ; +#endif +#endif + } + } + if (smc->os.hwm.tx_mb) { +#ifndef USE_OS_CPY + DB_TX("copy fragment into MBuf ",0,0,3) ; + memcpy(smc->os.hwm.tx_data,virt,len) ; + smc->os.hwm.tx_data += len ; +#endif + if (frame_status & LAST_FRAG) { +#ifdef USE_OS_CPY +#ifndef PASS_1ST_TXD_2_TX_COMP + /* + * hwm_cpy_txd2mb(txd,data,len) copies 'len' + * bytes from the virtual pointer in 'rxd' + * to 'data'. The virtual pointer of the + * os-specific tx-buffer should be written + * in the LAST txd. + */ + hwm_cpy_txd2mb(t,smc->os.hwm.tx_data, + smc->os.hwm.tx_len) ; +#endif /* nPASS_1ST_TXD_2_TX_COMP */ +#endif /* USE_OS_CPY */ + smc->os.hwm.tx_data = + smtod(smc->os.hwm.tx_mb,char *) - 1 ; + *(char *)smc->os.hwm.tx_mb->sm_data = + *smc->os.hwm.tx_data ; + smc->os.hwm.tx_data++ ; + smc->os.hwm.tx_mb->sm_len = + smc->os.hwm.tx_len - 1 ; + DB_TX("pass LLC frame to SMT ",0,0,3) ; + smt_received_pack(smc,smc->os.hwm.tx_mb, + RD_FS_LOCAL) ; + } + } + } + NDD_TRACE("THfE",t,queue->tx_free,0) ; +} + + +/* + * queues a receive for later send + */ +static void queue_llc_rx(struct s_smc *smc, SMbuf *mb) +{ + DB_GEN("queue_llc_rx: mb = %x",(void *)mb,0,4) ; + smc->os.hwm.queued_rx_frames++ ; + mb->sm_next = (SMbuf *)NULL ; + if (smc->os.hwm.llc_rx_pipe == NULL) { + smc->os.hwm.llc_rx_pipe = mb ; + } + else { + smc->os.hwm.llc_rx_tail->sm_next = mb ; + } + smc->os.hwm.llc_rx_tail = mb ; + + /* + * force an timer IRQ to receive the data + */ + if (!smc->os.hwm.isr_flag) { + smt_force_irq(smc) ; + } +} + +/* + * get a SMbuf from the llc_rx_queue + */ +static SMbuf *get_llc_rx(struct s_smc *smc) +{ + SMbuf *mb ; + + if ((mb = smc->os.hwm.llc_rx_pipe)) { + smc->os.hwm.queued_rx_frames-- ; + smc->os.hwm.llc_rx_pipe = mb->sm_next ; + } + DB_GEN("get_llc_rx: mb = 0x%x",(void *)mb,0,4) ; + return mb; +} + +/* + * queues a transmit SMT MBuf during the time were the MBuf is + * queued the TxD ring + */ +static void queue_txd_mb(struct s_smc *smc, SMbuf *mb) +{ + DB_GEN("_rx: queue_txd_mb = %x",(void *)mb,0,4) ; + smc->os.hwm.queued_txd_mb++ ; + mb->sm_next = (SMbuf *)NULL ; + if (smc->os.hwm.txd_tx_pipe == NULL) { + smc->os.hwm.txd_tx_pipe = mb ; + } + else { + smc->os.hwm.txd_tx_tail->sm_next = mb ; + } + smc->os.hwm.txd_tx_tail = mb ; +} + +/* + * get a SMbuf from the txd_tx_queue + */ +static SMbuf *get_txd_mb(struct s_smc *smc) +{ + SMbuf *mb ; + + if ((mb = smc->os.hwm.txd_tx_pipe)) { + smc->os.hwm.queued_txd_mb-- ; + smc->os.hwm.txd_tx_pipe = mb->sm_next ; + } + DB_GEN("get_txd_mb: mb = 0x%x",(void *)mb,0,4) ; + return mb; +} + +/* + * SMT Send function + */ +void smt_send_mbuf(struct s_smc *smc, SMbuf *mb, int fc) +{ + char far *data ; + int len ; + int n ; + int i ; + int frag_count ; + int frame_status ; + SK_LOC_DECL(char far,*virt[3]) ; + int frag_len[3] ; + struct s_smt_tx_queue *queue ; + struct s_smt_fp_txd volatile *t ; + u_long phys ; + __le32 tbctrl; + + NDD_TRACE("THSB",mb,fc,0) ; + DB_TX("smt_send_mbuf: mb = 0x%x, fc = 0x%x",mb,fc,4) ; + + mb->sm_off-- ; /* set to fc */ + mb->sm_len++ ; /* + fc */ + data = smtod(mb,char *) ; + *data = fc ; + if (fc == FC_SMT_LOC) + *data = FC_SMT_INFO ; + + /* + * determine the frag count and the virt addresses of the frags + */ + frag_count = 0 ; + len = mb->sm_len ; + while (len) { + n = SMT_PAGESIZE - ((long)data & (SMT_PAGESIZE-1)) ; + if (n >= len) { + n = len ; + } + DB_TX("frag: virt/len = 0x%x/%d ",(void *)data,n,5) ; + virt[frag_count] = data ; + frag_len[frag_count] = n ; + frag_count++ ; + len -= n ; + data += n ; + } + + /* + * determine the frame status + */ + queue = smc->hw.fp.tx[QUEUE_A0] ; + if (fc == FC_BEACON || fc == FC_SMT_LOC) { + frame_status = LOC_TX ; + } + else { + frame_status = LAN_TX ; + if ((smc->os.hwm.pass_NSA &&(fc == FC_SMT_NSA)) || + (smc->os.hwm.pass_SMT &&(fc == FC_SMT_INFO))) + frame_status |= LOC_TX ; + } + + if (!smc->hw.mac_ring_is_up || frag_count > queue->tx_free) { + frame_status &= ~LAN_TX; + if (frame_status) { + DB_TX("Ring is down: terminate LAN_TX",0,0,2) ; + } + else { + DB_TX("Ring is down: terminate transmission",0,0,2) ; + smt_free_mbuf(smc,mb) ; + return ; + } + } + DB_TX("frame_status = 0x%x ",frame_status,0,5) ; + + if ((frame_status & LAN_TX) && (frame_status & LOC_TX)) { + mb->sm_use_count = 2 ; + } + + if (frame_status & LAN_TX) { + t = queue->tx_curr_put ; + frame_status |= FIRST_FRAG ; + for (i = 0; i < frag_count; i++) { + DB_TX("init TxD = 0x%x",(void *)t,0,5) ; + if (i == frag_count-1) { + frame_status |= LAST_FRAG ; + t->txd_txdscr = cpu_to_le32(TX_DESCRIPTOR | + (((__u32)(mb->sm_len-1)&3) << 27)) ; + } + t->txd_virt = virt[i] ; + phys = dma_master(smc, (void far *)virt[i], + frag_len[i], DMA_RD|SMT_BUF) ; + t->txd_tbadr = cpu_to_le32(phys) ; + tbctrl = cpu_to_le32((((__u32)frame_status & + (FIRST_FRAG|LAST_FRAG)) << 26) | + BMU_OWN | BMU_CHECK | BMU_SMT_TX |frag_len[i]) ; + t->txd_tbctrl = tbctrl ; +#ifndef AIX + DRV_BUF_FLUSH(t,DDI_DMA_SYNC_FORDEV) ; + outpd(queue->tx_bmu_ctl,CSR_START) ; +#else + DRV_BUF_FLUSH(t,DDI_DMA_SYNC_FORDEV) ; + outpd(ADDR(B0_XA_CSR),CSR_START) ; +#endif + frame_status &= ~FIRST_FRAG ; + queue->tx_curr_put = t = t->txd_next ; + queue->tx_free-- ; + queue->tx_used++ ; + } + smc->mib.m[MAC0].fddiMACTransmit_Ct++ ; + queue_txd_mb(smc,mb) ; + } + + if (frame_status & LOC_TX) { + DB_TX("pass Mbuf to LLC queue",0,0,5) ; + queue_llc_rx(smc,mb) ; + } + + /* + * We need to unqueue the free SMT_MBUFs here, because it may + * be that the SMT want's to send more than 1 frame for one down call + */ + mac_drv_clear_txd(smc) ; + NDD_TRACE("THSE",t,queue->tx_free,frag_count) ; +} + +/* BEGIN_MANUAL_ENTRY(mac_drv_clear_txd) + * void mac_drv_clear_txd(smc) + * + * function DOWNCALL (hardware module, hwmtm.c) + * mac_drv_clear_txd searches in both send queues for TxD's + * which were finished by the adapter. It calls dma_complete + * for each TxD. If the last fragment of an LLC frame is + * reached, it calls mac_drv_tx_complete to release the + * send buffer. + * + * return nothing + * + * END_MANUAL_ENTRY + */ +static void mac_drv_clear_txd(struct s_smc *smc) +{ + struct s_smt_tx_queue *queue ; + struct s_smt_fp_txd volatile *t1 ; + struct s_smt_fp_txd volatile *t2 = NULL ; + SMbuf *mb ; + u_long tbctrl ; + int i ; + int frag_count ; + int n ; + + NDD_TRACE("THcB",0,0,0) ; + for (i = QUEUE_S; i <= QUEUE_A0; i++) { + queue = smc->hw.fp.tx[i] ; + t1 = queue->tx_curr_get ; + DB_TX("clear_txd: QUEUE = %d (0=sync/1=async)",i,0,5) ; + + for ( ; ; ) { + frag_count = 0 ; + + do { + DRV_BUF_FLUSH(t1,DDI_DMA_SYNC_FORCPU) ; + DB_TX("check OWN/EOF bit of TxD 0x%x",t1,0,5) ; + tbctrl = le32_to_cpu(CR_READ(t1->txd_tbctrl)); + + if (tbctrl & BMU_OWN || !queue->tx_used){ + DB_TX("End of TxDs queue %d",i,0,4) ; + goto free_next_queue ; /* next queue */ + } + t1 = t1->txd_next ; + frag_count++ ; + } while (!(tbctrl & BMU_EOF)) ; + + t1 = queue->tx_curr_get ; + for (n = frag_count; n; n--) { + tbctrl = le32_to_cpu(t1->txd_tbctrl) ; + dma_complete(smc, + (union s_fp_descr volatile *) t1, + (int) (DMA_RD | + ((tbctrl & BMU_SMT_TX) >> 18))) ; + t2 = t1 ; + t1 = t1->txd_next ; + } + + if (tbctrl & BMU_SMT_TX) { + mb = get_txd_mb(smc) ; + smt_free_mbuf(smc,mb) ; + } + else { +#ifndef PASS_1ST_TXD_2_TX_COMP + DB_TX("mac_drv_tx_comp for TxD 0x%x",t2,0,4) ; + mac_drv_tx_complete(smc,t2) ; +#else + DB_TX("mac_drv_tx_comp for TxD 0x%x", + queue->tx_curr_get,0,4) ; + mac_drv_tx_complete(smc,queue->tx_curr_get) ; +#endif + } + queue->tx_curr_get = t1 ; + queue->tx_free += frag_count ; + queue->tx_used -= frag_count ; + } +free_next_queue: ; + } + NDD_TRACE("THcE",0,0,0) ; +} + +/* + * BEGINN_MANUAL_ENTRY(mac_drv_clear_tx_queue) + * + * void mac_drv_clear_tx_queue(smc) + * struct s_smc *smc ; + * + * function DOWNCALL (hardware module, hwmtm.c) + * mac_drv_clear_tx_queue is called from the SMT when + * the RMT state machine has entered the ISOLATE state. + * This function is also called by the os-specific module + * after it has called the function card_stop(). + * In this case, the frames in the send queues are obsolete and + * should be removed. + * + * note calling sequence: + * CLI_FBI(), card_stop(), + * mac_drv_clear_tx_queue(), mac_drv_clear_rx_queue(), + * + * NOTE: The caller is responsible that the BMUs are idle + * when this function is called. + * + * END_MANUAL_ENTRY + */ +void mac_drv_clear_tx_queue(struct s_smc *smc) +{ + struct s_smt_fp_txd volatile *t ; + struct s_smt_tx_queue *queue ; + int tx_used ; + int i ; + + if (smc->hw.hw_state != STOPPED) { + SK_BREAK() ; + SMT_PANIC(smc,HWM_E0011,HWM_E0011_MSG) ; + return ; + } + + for (i = QUEUE_S; i <= QUEUE_A0; i++) { + queue = smc->hw.fp.tx[i] ; + DB_TX("clear_tx_queue: QUEUE = %d (0=sync/1=async)",i,0,5) ; + + /* + * switch the OWN bit of all pending frames to the host + */ + t = queue->tx_curr_get ; + tx_used = queue->tx_used ; + while (tx_used) { + DRV_BUF_FLUSH(t,DDI_DMA_SYNC_FORCPU) ; + DB_TX("switch OWN bit of TxD 0x%x ",t,0,5) ; + t->txd_tbctrl &= ~cpu_to_le32(BMU_OWN) ; + DRV_BUF_FLUSH(t,DDI_DMA_SYNC_FORDEV) ; + t = t->txd_next ; + tx_used-- ; + } + } + + /* + * release all TxD's for both send queues + */ + mac_drv_clear_txd(smc) ; + + for (i = QUEUE_S; i <= QUEUE_A0; i++) { + queue = smc->hw.fp.tx[i] ; + t = queue->tx_curr_get ; + + /* + * write the phys pointer of the NEXT descriptor into the + * BMU's current address descriptor pointer and set + * tx_curr_get and tx_curr_put to this position + */ + if (i == QUEUE_S) { + outpd(ADDR(B5_XS_DA),le32_to_cpu(t->txd_ntdadr)) ; + } + else { + outpd(ADDR(B5_XA_DA),le32_to_cpu(t->txd_ntdadr)) ; + } + + queue->tx_curr_put = queue->tx_curr_get->txd_next ; + queue->tx_curr_get = queue->tx_curr_put ; + } +} + + +/* + ------------------------------------------------------------- + TEST FUNCTIONS: + ------------------------------------------------------------- +*/ + +#ifdef DEBUG +/* + * BEGIN_MANUAL_ENTRY(mac_drv_debug_lev) + * void mac_drv_debug_lev(smc,flag,lev) + * + * function DOWNCALL (drvsr.c) + * To get a special debug info the user can assign a debug level + * to any debug flag. + * + * para flag debug flag, possible values are: + * = 0: reset all debug flags (the defined level is + * ignored) + * = 1: debug.d_smtf + * = 2: debug.d_smt + * = 3: debug.d_ecm + * = 4: debug.d_rmt + * = 5: debug.d_cfm + * = 6: debug.d_pcm + * + * = 10: debug.d_os.hwm_rx (hardware module receive path) + * = 11: debug.d_os.hwm_tx(hardware module transmit path) + * = 12: debug.d_os.hwm_gen(hardware module general flag) + * + * lev debug level + * + * END_MANUAL_ENTRY + */ +void mac_drv_debug_lev(struct s_smc *smc, int flag, int lev) +{ + switch(flag) { + case (int)NULL: + DB_P.d_smtf = DB_P.d_smt = DB_P.d_ecm = DB_P.d_rmt = 0 ; + DB_P.d_cfm = 0 ; + DB_P.d_os.hwm_rx = DB_P.d_os.hwm_tx = DB_P.d_os.hwm_gen = 0 ; +#ifdef SBA + DB_P.d_sba = 0 ; +#endif +#ifdef ESS + DB_P.d_ess = 0 ; +#endif + break ; + case DEBUG_SMTF: + DB_P.d_smtf = lev ; + break ; + case DEBUG_SMT: + DB_P.d_smt = lev ; + break ; + case DEBUG_ECM: + DB_P.d_ecm = lev ; + break ; + case DEBUG_RMT: + DB_P.d_rmt = lev ; + break ; + case DEBUG_CFM: + DB_P.d_cfm = lev ; + break ; + case DEBUG_PCM: + DB_P.d_pcm = lev ; + break ; + case DEBUG_SBA: +#ifdef SBA + DB_P.d_sba = lev ; +#endif + break ; + case DEBUG_ESS: +#ifdef ESS + DB_P.d_ess = lev ; +#endif + break ; + case DB_HWM_RX: + DB_P.d_os.hwm_rx = lev ; + break ; + case DB_HWM_TX: + DB_P.d_os.hwm_tx = lev ; + break ; + case DB_HWM_GEN: + DB_P.d_os.hwm_gen = lev ; + break ; + default: + break ; + } +} +#endif diff --git a/kernel/drivers/net/fddi/skfp/hwt.c b/kernel/drivers/net/fddi/skfp/hwt.c new file mode 100644 index 000000000..c0798fd2c --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/hwt.c @@ -0,0 +1,269 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + * Timer Driver for FBI board (timer chip 82C54) + */ + +/* + * Modifications: + * + * 28-Jun-1994 sw Edit v1.6. + * MCA: Added support for the SK-NET FDDI-FM2 adapter. The + * following functions have been added(+) or modified(*): + * hwt_start(*), hwt_stop(*), hwt_restart(*), hwt_read(*) + */ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)hwt.c 1.13 97/04/23 (C) SK " ; +#endif + +/* + * Prototypes of local functions. + */ +/* 28-Jun-1994 sw - Note: hwt_restart() is also used in module 'drvfbi.c'. */ +/*static void hwt_restart() ; */ + +/************************ + * + * hwt_start + * + * Start hardware timer (clock ticks are 16us). + * + * void hwt_start( + * struct s_smc *smc, + * u_long time) ; + * In + * smc - A pointer to the SMT Context structure. + * + * time - The time in units of 16us to load the timer with. + * Out + * Nothing. + * + ************************/ +#define HWT_MAX (65000) + +void hwt_start(struct s_smc *smc, u_long time) +{ + u_short cnt ; + + if (time > HWT_MAX) + time = HWT_MAX ; + + smc->hw.t_start = time ; + smc->hw.t_stop = 0L ; + + cnt = (u_short)time ; + /* + * if time < 16 us + * time = 16 us + */ + if (!cnt) + cnt++ ; + + outpd(ADDR(B2_TI_INI), (u_long) cnt * 200) ; /* Load timer value. */ + outpw(ADDR(B2_TI_CRTL), TIM_START) ; /* Start timer. */ + + smc->hw.timer_activ = TRUE ; +} + +/************************ + * + * hwt_stop + * + * Stop hardware timer. + * + * void hwt_stop( + * struct s_smc *smc) ; + * In + * smc - A pointer to the SMT Context structure. + * Out + * Nothing. + * + ************************/ +void hwt_stop(struct s_smc *smc) +{ + outpw(ADDR(B2_TI_CRTL), TIM_STOP) ; + outpw(ADDR(B2_TI_CRTL), TIM_CL_IRQ) ; + + smc->hw.timer_activ = FALSE ; +} + +/************************ + * + * hwt_init + * + * Initialize hardware timer. + * + * void hwt_init( + * struct s_smc *smc) ; + * In + * smc - A pointer to the SMT Context structure. + * Out + * Nothing. + * + ************************/ +void hwt_init(struct s_smc *smc) +{ + smc->hw.t_start = 0 ; + smc->hw.t_stop = 0 ; + smc->hw.timer_activ = FALSE ; + + hwt_restart(smc) ; +} + +/************************ + * + * hwt_restart + * + * Clear timer interrupt. + * + * void hwt_restart( + * struct s_smc *smc) ; + * In + * smc - A pointer to the SMT Context structure. + * Out + * Nothing. + * + ************************/ +void hwt_restart(struct s_smc *smc) +{ + hwt_stop(smc) ; +} + +/************************ + * + * hwt_read + * + * Stop hardware timer and read time elapsed since last start. + * + * u_long hwt_read(smc) ; + * In + * smc - A pointer to the SMT Context structure. + * Out + * The elapsed time since last start in units of 16us. + * + ************************/ +u_long hwt_read(struct s_smc *smc) +{ + u_short tr ; + u_long is ; + + if (smc->hw.timer_activ) { + hwt_stop(smc) ; + tr = (u_short)((inpd(ADDR(B2_TI_VAL))/200) & 0xffff) ; + + is = GET_ISR() ; + /* Check if timer expired (or wraparound). */ + if ((tr > smc->hw.t_start) || (is & IS_TIMINT)) { + hwt_restart(smc) ; + smc->hw.t_stop = smc->hw.t_start ; + } + else + smc->hw.t_stop = smc->hw.t_start - tr ; + } + return smc->hw.t_stop; +} + +#ifdef PCI +/************************ + * + * hwt_quick_read + * + * Stop hardware timer and read timer value and start the timer again. + * + * u_long hwt_read(smc) ; + * In + * smc - A pointer to the SMT Context structure. + * Out + * current timer value in units of 80ns. + * + ************************/ +u_long hwt_quick_read(struct s_smc *smc) +{ + u_long interval ; + u_long time ; + + interval = inpd(ADDR(B2_TI_INI)) ; + outpw(ADDR(B2_TI_CRTL), TIM_STOP) ; + time = inpd(ADDR(B2_TI_VAL)) ; + outpd(ADDR(B2_TI_INI),time) ; + outpw(ADDR(B2_TI_CRTL), TIM_START) ; + outpd(ADDR(B2_TI_INI),interval) ; + + return time; +} + +/************************ + * + * hwt_wait_time(smc,start,duration) + * + * This function returnes after the amount of time is elapsed + * since the start time. + * + * para start start time + * duration time to wait + * + * NOTE: The function will return immediately, if the timer is not + * started + ************************/ +void hwt_wait_time(struct s_smc *smc, u_long start, long int duration) +{ + long diff ; + long interval ; + int wrapped ; + + /* + * check if timer is running + */ + if (smc->hw.timer_activ == FALSE || + hwt_quick_read(smc) == hwt_quick_read(smc)) { + return ; + } + + interval = inpd(ADDR(B2_TI_INI)) ; + if (interval > duration) { + do { + diff = (long)(start - hwt_quick_read(smc)) ; + if (diff < 0) { + diff += interval ; + } + } while (diff <= duration) ; + } + else { + diff = interval ; + wrapped = 0 ; + do { + if (!wrapped) { + if (hwt_quick_read(smc) >= start) { + diff += interval ; + wrapped = 1 ; + } + } + else { + if (hwt_quick_read(smc) < start) { + wrapped = 0 ; + } + } + } while (diff <= duration) ; + } +} +#endif + diff --git a/kernel/drivers/net/fddi/skfp/pcmplc.c b/kernel/drivers/net/fddi/skfp/pcmplc.c new file mode 100644 index 000000000..88d02d0a4 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/pcmplc.c @@ -0,0 +1,2014 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + PCM + Physical Connection Management +*/ + +/* + * Hardware independent state machine implemantation + * The following external SMT functions are referenced : + * + * queue_event() + * smt_timer_start() + * smt_timer_stop() + * + * The following external HW dependent functions are referenced : + * sm_pm_control() + * sm_ph_linestate() + * sm_pm_ls_latch() + * + * The following HW dependent events are required : + * PC_QLS + * PC_ILS + * PC_HLS + * PC_MLS + * PC_NSE + * PC_LEM + * + */ + + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/supern_2.h" +#define KERNEL +#include "h/smtstate.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)pcmplc.c 2.55 99/08/05 (C) SK " ; +#endif + +#ifdef FDDI_MIB +extern int snmp_fddi_trap( +#ifdef ANSIC +struct s_smc * smc, int type, int index +#endif +); +#endif +#ifdef CONCENTRATOR +extern int plc_is_installed( +#ifdef ANSIC +struct s_smc *smc , +int p +#endif +) ; +#endif +/* + * FSM Macros + */ +#define AFLAG (0x20) +#define GO_STATE(x) (mib->fddiPORTPCMState = (x)|AFLAG) +#define ACTIONS_DONE() (mib->fddiPORTPCMState &= ~AFLAG) +#define ACTIONS(x) (x|AFLAG) + +/* + * PCM states + */ +#define PC0_OFF 0 +#define PC1_BREAK 1 +#define PC2_TRACE 2 +#define PC3_CONNECT 3 +#define PC4_NEXT 4 +#define PC5_SIGNAL 5 +#define PC6_JOIN 6 +#define PC7_VERIFY 7 +#define PC8_ACTIVE 8 +#define PC9_MAINT 9 + +#ifdef DEBUG +/* + * symbolic state names + */ +static const char * const pcm_states[] = { + "PC0_OFF","PC1_BREAK","PC2_TRACE","PC3_CONNECT","PC4_NEXT", + "PC5_SIGNAL","PC6_JOIN","PC7_VERIFY","PC8_ACTIVE","PC9_MAINT" +} ; + +/* + * symbolic event names + */ +static const char * const pcm_events[] = { + "NONE","PC_START","PC_STOP","PC_LOOP","PC_JOIN","PC_SIGNAL", + "PC_REJECT","PC_MAINT","PC_TRACE","PC_PDR", + "PC_ENABLE","PC_DISABLE", + "PC_QLS","PC_ILS","PC_MLS","PC_HLS","PC_LS_PDR","PC_LS_NONE", + "PC_TIMEOUT_TB_MAX","PC_TIMEOUT_TB_MIN", + "PC_TIMEOUT_C_MIN","PC_TIMEOUT_T_OUT", + "PC_TIMEOUT_TL_MIN","PC_TIMEOUT_T_NEXT","PC_TIMEOUT_LCT", + "PC_NSE","PC_LEM" +} ; +#endif + +#ifdef MOT_ELM +/* + * PCL-S control register + * this register in the PLC-S controls the scrambling parameters + */ +#define PLCS_CONTROL_C_U 0 +#define PLCS_CONTROL_C_S (PL_C_SDOFF_ENABLE | PL_C_SDON_ENABLE | \ + PL_C_CIPHER_ENABLE) +#define PLCS_FASSERT_U 0 +#define PLCS_FASSERT_S 0xFd76 /* 52.0 us */ +#define PLCS_FDEASSERT_U 0 +#define PLCS_FDEASSERT_S 0 +#else /* nMOT_ELM */ +/* + * PCL-S control register + * this register in the PLC-S controls the scrambling parameters + * can be patched for ANSI compliance if standard changes + */ +static const u_char plcs_control_c_u[17] = "PLC_CNTRL_C_U=\0\0" ; +static const u_char plcs_control_c_s[17] = "PLC_CNTRL_C_S=\01\02" ; + +#define PLCS_CONTROL_C_U (plcs_control_c_u[14] | (plcs_control_c_u[15]<<8)) +#define PLCS_CONTROL_C_S (plcs_control_c_s[14] | (plcs_control_c_s[15]<<8)) +#endif /* nMOT_ELM */ + +/* + * external vars + */ +/* struct definition see 'cmtdef.h' (also used by CFM) */ + +#define PS_OFF 0 +#define PS_BIT3 1 +#define PS_BIT4 2 +#define PS_BIT7 3 +#define PS_LCT 4 +#define PS_BIT8 5 +#define PS_JOIN 6 +#define PS_ACTIVE 7 + +#define LCT_LEM_MAX 255 + +/* + * PLC timing parameter + */ + +#define PLC_MS(m) ((int)((0x10000L-(m*100000L/2048)))) +#define SLOW_TL_MIN PLC_MS(6) +#define SLOW_C_MIN PLC_MS(10) + +static const struct plt { + int timer ; /* relative plc timer address */ + int para ; /* default timing parameters */ +} pltm[] = { + { PL_C_MIN, SLOW_C_MIN }, /* min t. to remain Connect State */ + { PL_TL_MIN, SLOW_TL_MIN }, /* min t. to transmit a Line State */ + { PL_TB_MIN, TP_TB_MIN }, /* min break time */ + { PL_T_OUT, TP_T_OUT }, /* Signaling timeout */ + { PL_LC_LENGTH, TP_LC_LENGTH }, /* Link Confidence Test Time */ + { PL_T_SCRUB, TP_T_SCRUB }, /* Scrub Time == MAC TVX time ! */ + { PL_NS_MAX, TP_NS_MAX }, /* max t. that noise is tolerated */ + { 0,0 } +} ; + +/* + * interrupt mask + */ +#ifdef SUPERNET_3 +/* + * Do we need the EBUF error during signaling, too, to detect SUPERNET_3 + * PLL bug? + */ +static const int plc_imsk_na = PL_PCM_CODE | PL_TRACE_PROP | PL_PCM_BREAK | + PL_PCM_ENABLED | PL_SELF_TEST | PL_EBUF_ERR; +#else /* SUPERNET_3 */ +/* + * We do NOT need the elasticity buffer error during signaling. + */ +static int plc_imsk_na = PL_PCM_CODE | PL_TRACE_PROP | PL_PCM_BREAK | + PL_PCM_ENABLED | PL_SELF_TEST ; +#endif /* SUPERNET_3 */ +static const int plc_imsk_act = PL_PCM_CODE | PL_TRACE_PROP | PL_PCM_BREAK | + PL_PCM_ENABLED | PL_SELF_TEST | PL_EBUF_ERR; + +/* internal functions */ +static void pcm_fsm(struct s_smc *smc, struct s_phy *phy, int cmd); +static void pc_rcode_actions(struct s_smc *smc, int bit, struct s_phy *phy); +static void pc_tcode_actions(struct s_smc *smc, const int bit, struct s_phy *phy); +static void reset_lem_struct(struct s_phy *phy); +static void plc_init(struct s_smc *smc, int p); +static void sm_ph_lem_start(struct s_smc *smc, int np, int threshold); +static void sm_ph_lem_stop(struct s_smc *smc, int np); +static void sm_ph_linestate(struct s_smc *smc, int phy, int ls); +static void real_init_plc(struct s_smc *smc); + +/* + * SMT timer interface + * start PCM timer 0 + */ +static void start_pcm_timer0(struct s_smc *smc, u_long value, int event, + struct s_phy *phy) +{ + phy->timer0_exp = FALSE ; /* clear timer event flag */ + smt_timer_start(smc,&phy->pcm_timer0,value, + EV_TOKEN(EVENT_PCM+phy->np,event)) ; +} +/* + * SMT timer interface + * stop PCM timer 0 + */ +static void stop_pcm_timer0(struct s_smc *smc, struct s_phy *phy) +{ + if (phy->pcm_timer0.tm_active) + smt_timer_stop(smc,&phy->pcm_timer0) ; +} + +/* + init PCM state machine (called by driver) + clear all PCM vars and flags +*/ +void pcm_init(struct s_smc *smc) +{ + int i ; + int np ; + struct s_phy *phy ; + struct fddi_mib_p *mib ; + + for (np = 0,phy = smc->y ; np < NUMPHYS ; np++,phy++) { + /* Indicates the type of PHY being used */ + mib = phy->mib ; + mib->fddiPORTPCMState = ACTIONS(PC0_OFF) ; + phy->np = np ; + switch (smc->s.sas) { +#ifdef CONCENTRATOR + case SMT_SAS : + mib->fddiPORTMy_Type = (np == PS) ? TS : TM ; + break ; + case SMT_DAS : + mib->fddiPORTMy_Type = (np == PA) ? TA : + (np == PB) ? TB : TM ; + break ; + case SMT_NAC : + mib->fddiPORTMy_Type = TM ; + break; +#else + case SMT_SAS : + mib->fddiPORTMy_Type = (np == PS) ? TS : TNONE ; + mib->fddiPORTHardwarePresent = (np == PS) ? TRUE : + FALSE ; +#ifndef SUPERNET_3 + smc->y[PA].mib->fddiPORTPCMState = PC0_OFF ; +#else + smc->y[PB].mib->fddiPORTPCMState = PC0_OFF ; +#endif + break ; + case SMT_DAS : + mib->fddiPORTMy_Type = (np == PB) ? TB : TA ; + break ; +#endif + } + /* + * set PMD-type + */ + phy->pmd_scramble = 0 ; + switch (phy->pmd_type[PMD_SK_PMD]) { + case 'P' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_MULTI ; + break ; + case 'L' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_LCF ; + break ; + case 'D' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_TP ; + break ; + case 'S' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_TP ; + phy->pmd_scramble = TRUE ; + break ; + case 'U' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_TP ; + phy->pmd_scramble = TRUE ; + break ; + case '1' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_SINGLE1 ; + break ; + case '2' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_SINGLE2 ; + break ; + case '3' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_SINGLE2 ; + break ; + case '4' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_SINGLE1 ; + break ; + case 'H' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_UNKNOWN ; + break ; + case 'I' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_TP ; + break ; + case 'G' : + mib->fddiPORTPMDClass = MIB_PMDCLASS_TP ; + break ; + default: + mib->fddiPORTPMDClass = MIB_PMDCLASS_UNKNOWN ; + break ; + } + /* + * A and B port can be on primary and secondary path + */ + switch (mib->fddiPORTMy_Type) { + case TA : + mib->fddiPORTAvailablePaths |= MIB_PATH_S ; + mib->fddiPORTRequestedPaths[1] = MIB_P_PATH_LOCAL ; + mib->fddiPORTRequestedPaths[2] = + MIB_P_PATH_LOCAL | + MIB_P_PATH_CON_ALTER | + MIB_P_PATH_SEC_PREFER ; + mib->fddiPORTRequestedPaths[3] = + MIB_P_PATH_LOCAL | + MIB_P_PATH_CON_ALTER | + MIB_P_PATH_SEC_PREFER | + MIB_P_PATH_THRU ; + break ; + case TB : + mib->fddiPORTAvailablePaths |= MIB_PATH_S ; + mib->fddiPORTRequestedPaths[1] = MIB_P_PATH_LOCAL ; + mib->fddiPORTRequestedPaths[2] = + MIB_P_PATH_LOCAL | + MIB_P_PATH_PRIM_PREFER ; + mib->fddiPORTRequestedPaths[3] = + MIB_P_PATH_LOCAL | + MIB_P_PATH_PRIM_PREFER | + MIB_P_PATH_CON_PREFER | + MIB_P_PATH_THRU ; + break ; + case TS : + mib->fddiPORTAvailablePaths |= MIB_PATH_S ; + mib->fddiPORTRequestedPaths[1] = MIB_P_PATH_LOCAL ; + mib->fddiPORTRequestedPaths[2] = + MIB_P_PATH_LOCAL | + MIB_P_PATH_CON_ALTER | + MIB_P_PATH_PRIM_PREFER ; + mib->fddiPORTRequestedPaths[3] = + MIB_P_PATH_LOCAL | + MIB_P_PATH_CON_ALTER | + MIB_P_PATH_PRIM_PREFER ; + break ; + case TM : + mib->fddiPORTRequestedPaths[1] = MIB_P_PATH_LOCAL ; + mib->fddiPORTRequestedPaths[2] = + MIB_P_PATH_LOCAL | + MIB_P_PATH_SEC_ALTER | + MIB_P_PATH_PRIM_ALTER ; + mib->fddiPORTRequestedPaths[3] = 0 ; + break ; + } + + phy->pc_lem_fail = FALSE ; + mib->fddiPORTPCMStateX = mib->fddiPORTPCMState ; + mib->fddiPORTLCTFail_Ct = 0 ; + mib->fddiPORTBS_Flag = 0 ; + mib->fddiPORTCurrentPath = MIB_PATH_ISOLATED ; + mib->fddiPORTNeighborType = TNONE ; + phy->ls_flag = 0 ; + phy->rc_flag = 0 ; + phy->tc_flag = 0 ; + phy->td_flag = 0 ; + if (np >= PM) + phy->phy_name = '0' + np - PM ; + else + phy->phy_name = 'A' + np ; + phy->wc_flag = FALSE ; /* set by SMT */ + memset((char *)&phy->lem,0,sizeof(struct lem_counter)) ; + reset_lem_struct(phy) ; + memset((char *)&phy->plc,0,sizeof(struct s_plc)) ; + phy->plc.p_state = PS_OFF ; + for (i = 0 ; i < NUMBITS ; i++) { + phy->t_next[i] = 0 ; + } + } + real_init_plc(smc) ; +} + +void init_plc(struct s_smc *smc) +{ + SK_UNUSED(smc) ; + + /* + * dummy + * this is an obsolete public entry point that has to remain + * for compat. It is used by various drivers. + * the work is now done in real_init_plc() + * which is called from pcm_init() ; + */ +} + +static void real_init_plc(struct s_smc *smc) +{ + int p ; + + for (p = 0 ; p < NUMPHYS ; p++) + plc_init(smc,p) ; +} + +static void plc_init(struct s_smc *smc, int p) +{ + int i ; +#ifndef MOT_ELM + int rev ; /* Revision of PLC-x */ +#endif /* MOT_ELM */ + + /* transit PCM state machine to MAINT state */ + outpw(PLC(p,PL_CNTRL_B),0) ; + outpw(PLC(p,PL_CNTRL_B),PL_PCM_STOP) ; + outpw(PLC(p,PL_CNTRL_A),0) ; + + /* + * if PLC-S then set control register C + */ +#ifndef MOT_ELM + rev = inpw(PLC(p,PL_STATUS_A)) & PLC_REV_MASK ; + if (rev != PLC_REVISION_A) +#endif /* MOT_ELM */ + { + if (smc->y[p].pmd_scramble) { + outpw(PLC(p,PL_CNTRL_C),PLCS_CONTROL_C_S) ; +#ifdef MOT_ELM + outpw(PLC(p,PL_T_FOT_ASS),PLCS_FASSERT_S) ; + outpw(PLC(p,PL_T_FOT_DEASS),PLCS_FDEASSERT_S) ; +#endif /* MOT_ELM */ + } + else { + outpw(PLC(p,PL_CNTRL_C),PLCS_CONTROL_C_U) ; +#ifdef MOT_ELM + outpw(PLC(p,PL_T_FOT_ASS),PLCS_FASSERT_U) ; + outpw(PLC(p,PL_T_FOT_DEASS),PLCS_FDEASSERT_U) ; +#endif /* MOT_ELM */ + } + } + + /* + * set timer register + */ + for ( i = 0 ; pltm[i].timer; i++) /* set timer parameter reg */ + outpw(PLC(p,pltm[i].timer),pltm[i].para) ; + + (void)inpw(PLC(p,PL_INTR_EVENT)) ; /* clear interrupt event reg */ + plc_clear_irq(smc,p) ; + outpw(PLC(p,PL_INTR_MASK),plc_imsk_na); /* enable non active irq's */ + + /* + * if PCM is configured for class s, it will NOT go to the + * REMOVE state if offline (page 3-36;) + * in the concentrator, all inactive PHYS always must be in + * the remove state + * there's no real need to use this feature at all .. + */ +#ifndef CONCENTRATOR + if ((smc->s.sas == SMT_SAS) && (p == PS)) { + outpw(PLC(p,PL_CNTRL_B),PL_CLASS_S) ; + } +#endif +} + +/* + * control PCM state machine + */ +static void plc_go_state(struct s_smc *smc, int p, int state) +{ + HW_PTR port ; + int val ; + + SK_UNUSED(smc) ; + + port = (HW_PTR) (PLC(p,PL_CNTRL_B)) ; + val = inpw(port) & ~(PL_PCM_CNTRL | PL_MAINT) ; + outpw(port,val) ; + outpw(port,val | state) ; +} + +/* + * read current line state (called by ECM & PCM) + */ +int sm_pm_get_ls(struct s_smc *smc, int phy) +{ + int state ; + +#ifdef CONCENTRATOR + if (!plc_is_installed(smc,phy)) + return PC_QLS; +#endif + + state = inpw(PLC(phy,PL_STATUS_A)) & PL_LINE_ST ; + switch(state) { + case PL_L_QLS: + state = PC_QLS ; + break ; + case PL_L_MLS: + state = PC_MLS ; + break ; + case PL_L_HLS: + state = PC_HLS ; + break ; + case PL_L_ILS4: + case PL_L_ILS16: + state = PC_ILS ; + break ; + case PL_L_ALS: + state = PC_LS_PDR ; + break ; + default : + state = PC_LS_NONE ; + } + return state; +} + +static int plc_send_bits(struct s_smc *smc, struct s_phy *phy, int len) +{ + int np = phy->np ; /* PHY index */ + int n ; + int i ; + + SK_UNUSED(smc) ; + + /* create bit vector */ + for (i = len-1,n = 0 ; i >= 0 ; i--) { + n = (n<<1) | phy->t_val[phy->bitn+i] ; + } + if (inpw(PLC(np,PL_STATUS_B)) & PL_PCM_SIGNAL) { +#if 0 + printf("PL_PCM_SIGNAL is set\n") ; +#endif + return 1; + } + /* write bit[n] & length = 1 to regs */ + outpw(PLC(np,PL_VECTOR_LEN),len-1) ; /* len=nr-1 */ + outpw(PLC(np,PL_XMIT_VECTOR),n) ; +#ifdef DEBUG +#if 1 +#ifdef DEBUG_BRD + if (smc->debug.d_plc & 0x80) +#else + if (debug.d_plc & 0x80) +#endif + printf("SIGNALING bit %d .. %d\n",phy->bitn,phy->bitn+len-1) ; +#endif +#endif + return 0; +} + +/* + * config plc muxes + */ +void plc_config_mux(struct s_smc *smc, int mux) +{ + if (smc->s.sas != SMT_DAS) + return ; + if (mux == MUX_WRAPB) { + SETMASK(PLC(PA,PL_CNTRL_B),PL_CONFIG_CNTRL,PL_CONFIG_CNTRL) ; + SETMASK(PLC(PA,PL_CNTRL_A),PL_SC_REM_LOOP,PL_SC_REM_LOOP) ; + } + else { + CLEAR(PLC(PA,PL_CNTRL_B),PL_CONFIG_CNTRL) ; + CLEAR(PLC(PA,PL_CNTRL_A),PL_SC_REM_LOOP) ; + } + CLEAR(PLC(PB,PL_CNTRL_B),PL_CONFIG_CNTRL) ; + CLEAR(PLC(PB,PL_CNTRL_A),PL_SC_REM_LOOP) ; +} + +/* + PCM state machine + called by dispatcher & fddi_init() (driver) + do + display state change + process event + until SM is stable +*/ +void pcm(struct s_smc *smc, const int np, int event) +{ + int state ; + int oldstate ; + struct s_phy *phy ; + struct fddi_mib_p *mib ; + +#ifndef CONCENTRATOR + /* + * ignore 2nd PHY if SAS + */ + if ((np != PS) && (smc->s.sas == SMT_SAS)) + return ; +#endif + phy = &smc->y[np] ; + mib = phy->mib ; + oldstate = mib->fddiPORTPCMState ; + do { + DB_PCM("PCM %c: state %s", + phy->phy_name, + (mib->fddiPORTPCMState & AFLAG) ? "ACTIONS " : "") ; + DB_PCM("%s, event %s\n", + pcm_states[mib->fddiPORTPCMState & ~AFLAG], + pcm_events[event]) ; + state = mib->fddiPORTPCMState ; + pcm_fsm(smc,phy,event) ; + event = 0 ; + } while (state != mib->fddiPORTPCMState) ; + /* + * because the PLC does the bit signaling for us, + * we're always in SIGNAL state + * the MIB want's to see CONNECT + * we therefore fake an entry in the MIB + */ + if (state == PC5_SIGNAL) + mib->fddiPORTPCMStateX = PC3_CONNECT ; + else + mib->fddiPORTPCMStateX = state ; + +#ifndef SLIM_SMT + /* + * path change + */ + if ( mib->fddiPORTPCMState != oldstate && + ((oldstate == PC8_ACTIVE) || (mib->fddiPORTPCMState == PC8_ACTIVE))) { + smt_srf_event(smc,SMT_EVENT_PORT_PATH_CHANGE, + (int) (INDEX_PORT+ phy->np),0) ; + } +#endif + +#ifdef FDDI_MIB + /* check whether a snmp-trap has to be sent */ + + if ( mib->fddiPORTPCMState != oldstate ) { + /* a real state change took place */ + DB_SNMP ("PCM from %d to %d\n", oldstate, mib->fddiPORTPCMState); + if ( mib->fddiPORTPCMState == PC0_OFF ) { + /* send first trap */ + snmp_fddi_trap (smc, 1, (int) mib->fddiPORTIndex ); + } else if ( oldstate == PC0_OFF ) { + /* send second trap */ + snmp_fddi_trap (smc, 2, (int) mib->fddiPORTIndex ); + } else if ( mib->fddiPORTPCMState != PC2_TRACE && + oldstate == PC8_ACTIVE ) { + /* send third trap */ + snmp_fddi_trap (smc, 3, (int) mib->fddiPORTIndex ); + } else if ( mib->fddiPORTPCMState == PC8_ACTIVE ) { + /* send fourth trap */ + snmp_fddi_trap (smc, 4, (int) mib->fddiPORTIndex ); + } + } +#endif + + pcm_state_change(smc,np,state) ; +} + +/* + * PCM state machine + */ +static void pcm_fsm(struct s_smc *smc, struct s_phy *phy, int cmd) +{ + int i ; + int np = phy->np ; /* PHY index */ + struct s_plc *plc ; + struct fddi_mib_p *mib ; +#ifndef MOT_ELM + u_short plc_rev ; /* Revision of the plc */ +#endif /* nMOT_ELM */ + + plc = &phy->plc ; + mib = phy->mib ; + + /* + * general transitions independent of state + */ + switch (cmd) { + case PC_STOP : + /*PC00-PC80*/ + if (mib->fddiPORTPCMState != PC9_MAINT) { + GO_STATE(PC0_OFF) ; + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, (u_long) + FDDI_PORT_EVENT, (u_long) FDDI_PORT_STOP, + smt_get_port_event_word(smc)); + } + return ; + case PC_START : + /*PC01-PC81*/ + if (mib->fddiPORTPCMState != PC9_MAINT) + GO_STATE(PC1_BREAK) ; + return ; + case PC_DISABLE : + /* PC09-PC99 */ + GO_STATE(PC9_MAINT) ; + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, (u_long) + FDDI_PORT_EVENT, (u_long) FDDI_PORT_DISABLED, + smt_get_port_event_word(smc)); + return ; + case PC_TIMEOUT_LCT : + /* if long or extended LCT */ + stop_pcm_timer0(smc,phy) ; + CLEAR(PLC(np,PL_CNTRL_B),PL_LONG) ; + /* end of LCT is indicate by PCM_CODE (initiate PCM event) */ + return ; + } + + switch(mib->fddiPORTPCMState) { + case ACTIONS(PC0_OFF) : + stop_pcm_timer0(smc,phy) ; + outpw(PLC(np,PL_CNTRL_A),0) ; + CLEAR(PLC(np,PL_CNTRL_B),PL_PC_JOIN) ; + CLEAR(PLC(np,PL_CNTRL_B),PL_LONG) ; + sm_ph_lem_stop(smc,np) ; /* disable LEM */ + phy->cf_loop = FALSE ; + phy->cf_join = FALSE ; + queue_event(smc,EVENT_CFM,CF_JOIN+np) ; + plc_go_state(smc,np,PL_PCM_STOP) ; + mib->fddiPORTConnectState = PCM_DISABLED ; + ACTIONS_DONE() ; + break ; + case PC0_OFF: + /*PC09*/ + if (cmd == PC_MAINT) { + GO_STATE(PC9_MAINT) ; + break ; + } + break ; + case ACTIONS(PC1_BREAK) : + /* Stop the LCT timer if we came from Signal state */ + stop_pcm_timer0(smc,phy) ; + ACTIONS_DONE() ; + plc_go_state(smc,np,0) ; + CLEAR(PLC(np,PL_CNTRL_B),PL_PC_JOIN) ; + CLEAR(PLC(np,PL_CNTRL_B),PL_LONG) ; + sm_ph_lem_stop(smc,np) ; /* disable LEM */ + /* + * if vector is already loaded, go to OFF to clear PCM_SIGNAL + */ +#if 0 + if (inpw(PLC(np,PL_STATUS_B)) & PL_PCM_SIGNAL) { + plc_go_state(smc,np,PL_PCM_STOP) ; + /* TB_MIN ? */ + } +#endif + /* + * Go to OFF state in any case. + */ + plc_go_state(smc,np,PL_PCM_STOP) ; + + if (mib->fddiPORTPC_Withhold == PC_WH_NONE) + mib->fddiPORTConnectState = PCM_CONNECTING ; + phy->cf_loop = FALSE ; + phy->cf_join = FALSE ; + queue_event(smc,EVENT_CFM,CF_JOIN+np) ; + phy->ls_flag = FALSE ; + phy->pc_mode = PM_NONE ; /* needed by CFM */ + phy->bitn = 0 ; /* bit signaling start bit */ + for (i = 0 ; i < 3 ; i++) + pc_tcode_actions(smc,i,phy) ; + + /* Set the non-active interrupt mask register */ + outpw(PLC(np,PL_INTR_MASK),plc_imsk_na) ; + + /* + * If the LCT was stopped. There might be a + * PCM_CODE interrupt event present. + * This must be cleared. + */ + (void)inpw(PLC(np,PL_INTR_EVENT)) ; +#ifndef MOT_ELM + /* Get the plc revision for revision dependent code */ + plc_rev = inpw(PLC(np,PL_STATUS_A)) & PLC_REV_MASK ; + + if (plc_rev != PLC_REV_SN3) +#endif /* MOT_ELM */ + { + /* + * No supernet III PLC, so set Xmit verctor and + * length BEFORE starting the state machine. + */ + if (plc_send_bits(smc,phy,3)) { + return ; + } + } + + /* + * Now give the Start command. + * - The start command shall be done before setting the bits + * to be signaled. (In PLC-S description and PLCS in SN3. + * - The start command shall be issued AFTER setting the + * XMIT vector and the XMIT length register. + * + * We do it exactly according this specs for the old PLC and + * the new PLCS inside the SN3. + * For the usual PLCS we try it the way it is done for the + * old PLC and set the XMIT registers again, if the PLC is + * not in SIGNAL state. This is done according to an PLCS + * errata workaround. + */ + + plc_go_state(smc,np,PL_PCM_START) ; + + /* + * workaround for PLC-S eng. sample errata + */ +#ifdef MOT_ELM + if (!(inpw(PLC(np,PL_STATUS_B)) & PL_PCM_SIGNAL)) +#else /* nMOT_ELM */ + if (((inpw(PLC(np,PL_STATUS_A)) & PLC_REV_MASK) != + PLC_REVISION_A) && + !(inpw(PLC(np,PL_STATUS_B)) & PL_PCM_SIGNAL)) +#endif /* nMOT_ELM */ + { + /* + * Set register again (PLCS errata) or the first time + * (new SN3 PLCS). + */ + (void) plc_send_bits(smc,phy,3) ; + } + /* + * end of workaround + */ + + GO_STATE(PC5_SIGNAL) ; + plc->p_state = PS_BIT3 ; + plc->p_bits = 3 ; + plc->p_start = 0 ; + + break ; + case PC1_BREAK : + break ; + case ACTIONS(PC2_TRACE) : + plc_go_state(smc,np,PL_PCM_TRACE) ; + ACTIONS_DONE() ; + break ; + case PC2_TRACE : + break ; + + case PC3_CONNECT : /* these states are done by hardware */ + case PC4_NEXT : + break ; + + case ACTIONS(PC5_SIGNAL) : + ACTIONS_DONE() ; + case PC5_SIGNAL : + if ((cmd != PC_SIGNAL) && (cmd != PC_TIMEOUT_LCT)) + break ; + switch (plc->p_state) { + case PS_BIT3 : + for (i = 0 ; i <= 2 ; i++) + pc_rcode_actions(smc,i,phy) ; + pc_tcode_actions(smc,3,phy) ; + plc->p_state = PS_BIT4 ; + plc->p_bits = 1 ; + plc->p_start = 3 ; + phy->bitn = 3 ; + if (plc_send_bits(smc,phy,1)) { + return ; + } + break ; + case PS_BIT4 : + pc_rcode_actions(smc,3,phy) ; + for (i = 4 ; i <= 6 ; i++) + pc_tcode_actions(smc,i,phy) ; + plc->p_state = PS_BIT7 ; + plc->p_bits = 3 ; + plc->p_start = 4 ; + phy->bitn = 4 ; + if (plc_send_bits(smc,phy,3)) { + return ; + } + break ; + case PS_BIT7 : + for (i = 3 ; i <= 6 ; i++) + pc_rcode_actions(smc,i,phy) ; + plc->p_state = PS_LCT ; + plc->p_bits = 0 ; + plc->p_start = 7 ; + phy->bitn = 7 ; + sm_ph_lem_start(smc,np,(int)smc->s.lct_short) ; /* enable LEM */ + /* start LCT */ + i = inpw(PLC(np,PL_CNTRL_B)) & ~PL_PC_LOOP ; + outpw(PLC(np,PL_CNTRL_B),i) ; /* must be cleared */ + outpw(PLC(np,PL_CNTRL_B),i | PL_RLBP) ; + break ; + case PS_LCT : + /* check for local LCT failure */ + pc_tcode_actions(smc,7,phy) ; + /* + * set tval[7] + */ + plc->p_state = PS_BIT8 ; + plc->p_bits = 1 ; + plc->p_start = 7 ; + phy->bitn = 7 ; + if (plc_send_bits(smc,phy,1)) { + return ; + } + break ; + case PS_BIT8 : + /* check for remote LCT failure */ + pc_rcode_actions(smc,7,phy) ; + if (phy->t_val[7] || phy->r_val[7]) { + plc_go_state(smc,np,PL_PCM_STOP) ; + GO_STATE(PC1_BREAK) ; + break ; + } + for (i = 8 ; i <= 9 ; i++) + pc_tcode_actions(smc,i,phy) ; + plc->p_state = PS_JOIN ; + plc->p_bits = 2 ; + plc->p_start = 8 ; + phy->bitn = 8 ; + if (plc_send_bits(smc,phy,2)) { + return ; + } + break ; + case PS_JOIN : + for (i = 8 ; i <= 9 ; i++) + pc_rcode_actions(smc,i,phy) ; + plc->p_state = PS_ACTIVE ; + GO_STATE(PC6_JOIN) ; + break ; + } + break ; + + case ACTIONS(PC6_JOIN) : + /* + * prevent mux error when going from WRAP_A to WRAP_B + */ + if (smc->s.sas == SMT_DAS && np == PB && + (smc->y[PA].pc_mode == PM_TREE || + smc->y[PB].pc_mode == PM_TREE)) { + SETMASK(PLC(np,PL_CNTRL_A), + PL_SC_REM_LOOP,PL_SC_REM_LOOP) ; + SETMASK(PLC(np,PL_CNTRL_B), + PL_CONFIG_CNTRL,PL_CONFIG_CNTRL) ; + } + SETMASK(PLC(np,PL_CNTRL_B),PL_PC_JOIN,PL_PC_JOIN) ; + SETMASK(PLC(np,PL_CNTRL_B),PL_PC_JOIN,PL_PC_JOIN) ; + ACTIONS_DONE() ; + cmd = 0 ; + /* fall thru */ + case PC6_JOIN : + switch (plc->p_state) { + case PS_ACTIVE: + /*PC88b*/ + if (!phy->cf_join) { + phy->cf_join = TRUE ; + queue_event(smc,EVENT_CFM,CF_JOIN+np) ; + } + if (cmd == PC_JOIN) + GO_STATE(PC8_ACTIVE) ; + /*PC82*/ + if (cmd == PC_TRACE) { + GO_STATE(PC2_TRACE) ; + break ; + } + break ; + } + break ; + + case PC7_VERIFY : + break ; + + case ACTIONS(PC8_ACTIVE) : + /* + * start LEM for SMT + */ + sm_ph_lem_start(smc,(int)phy->np,LCT_LEM_MAX) ; + + phy->tr_flag = FALSE ; + mib->fddiPORTConnectState = PCM_ACTIVE ; + + /* Set the active interrupt mask register */ + outpw(PLC(np,PL_INTR_MASK),plc_imsk_act) ; + + ACTIONS_DONE() ; + break ; + case PC8_ACTIVE : + /*PC81 is done by PL_TNE_EXPIRED irq */ + /*PC82*/ + if (cmd == PC_TRACE) { + GO_STATE(PC2_TRACE) ; + break ; + } + /*PC88c: is done by TRACE_PROP irq */ + + break ; + case ACTIONS(PC9_MAINT) : + stop_pcm_timer0(smc,phy) ; + CLEAR(PLC(np,PL_CNTRL_B),PL_PC_JOIN) ; + CLEAR(PLC(np,PL_CNTRL_B),PL_LONG) ; + CLEAR(PLC(np,PL_INTR_MASK),PL_LE_CTR) ; /* disable LEM int. */ + sm_ph_lem_stop(smc,np) ; /* disable LEM */ + phy->cf_loop = FALSE ; + phy->cf_join = FALSE ; + queue_event(smc,EVENT_CFM,CF_JOIN+np) ; + plc_go_state(smc,np,PL_PCM_STOP) ; + mib->fddiPORTConnectState = PCM_DISABLED ; + SETMASK(PLC(np,PL_CNTRL_B),PL_MAINT,PL_MAINT) ; + sm_ph_linestate(smc,np,(int) MIB2LS(mib->fddiPORTMaint_LS)) ; + outpw(PLC(np,PL_CNTRL_A),PL_SC_BYPASS) ; + ACTIONS_DONE() ; + break ; + case PC9_MAINT : + DB_PCMN(1,"PCM %c : MAINT\n",phy->phy_name,0) ; + /*PC90*/ + if (cmd == PC_ENABLE) { + GO_STATE(PC0_OFF) ; + break ; + } + break ; + + default: + SMT_PANIC(smc,SMT_E0118, SMT_E0118_MSG) ; + break ; + } +} + +/* + * force line state on a PHY output (only in MAINT state) + */ +static void sm_ph_linestate(struct s_smc *smc, int phy, int ls) +{ + int cntrl ; + + SK_UNUSED(smc) ; + + cntrl = (inpw(PLC(phy,PL_CNTRL_B)) & ~PL_MAINT_LS) | + PL_PCM_STOP | PL_MAINT ; + switch(ls) { + case PC_QLS: /* Force Quiet */ + cntrl |= PL_M_QUI0 ; + break ; + case PC_MLS: /* Force Master */ + cntrl |= PL_M_MASTR ; + break ; + case PC_HLS: /* Force Halt */ + cntrl |= PL_M_HALT ; + break ; + default : + case PC_ILS: /* Force Idle */ + cntrl |= PL_M_IDLE ; + break ; + case PC_LS_PDR: /* Enable repeat filter */ + cntrl |= PL_M_TPDR ; + break ; + } + outpw(PLC(phy,PL_CNTRL_B),cntrl) ; +} + +static void reset_lem_struct(struct s_phy *phy) +{ + struct lem_counter *lem = &phy->lem ; + + phy->mib->fddiPORTLer_Estimate = 15 ; + lem->lem_float_ber = 15 * 100 ; +} + +/* + * link error monitor + */ +static void lem_evaluate(struct s_smc *smc, struct s_phy *phy) +{ + int ber ; + u_long errors ; + struct lem_counter *lem = &phy->lem ; + struct fddi_mib_p *mib ; + int cond ; + + mib = phy->mib ; + + if (!lem->lem_on) + return ; + + errors = inpw(PLC(((int) phy->np),PL_LINK_ERR_CTR)) ; + lem->lem_errors += errors ; + mib->fddiPORTLem_Ct += errors ; + + errors = lem->lem_errors ; + /* + * calculation is called on a intervall of 8 seconds + * -> this means, that one error in 8 sec. is one of 8*125*10E6 + * the same as BER = 10E-9 + * Please note: + * -> 9 errors in 8 seconds mean: + * BER = 9 * 10E-9 and this is + * < 10E-8, so the limit of 10E-8 is not reached! + */ + + if (!errors) ber = 15 ; + else if (errors <= 9) ber = 9 ; + else if (errors <= 99) ber = 8 ; + else if (errors <= 999) ber = 7 ; + else if (errors <= 9999) ber = 6 ; + else if (errors <= 99999) ber = 5 ; + else if (errors <= 999999) ber = 4 ; + else if (errors <= 9999999) ber = 3 ; + else if (errors <= 99999999) ber = 2 ; + else if (errors <= 999999999) ber = 1 ; + else ber = 0 ; + + /* + * weighted average + */ + ber *= 100 ; + lem->lem_float_ber = lem->lem_float_ber * 7 + ber * 3 ; + lem->lem_float_ber /= 10 ; + mib->fddiPORTLer_Estimate = lem->lem_float_ber / 100 ; + if (mib->fddiPORTLer_Estimate < 4) { + mib->fddiPORTLer_Estimate = 4 ; + } + + if (lem->lem_errors) { + DB_PCMN(1,"LEM %c :\n",phy->np == PB? 'B' : 'A',0) ; + DB_PCMN(1,"errors : %ld\n",lem->lem_errors,0) ; + DB_PCMN(1,"sum_errors : %ld\n",mib->fddiPORTLem_Ct,0) ; + DB_PCMN(1,"current BER : 10E-%d\n",ber/100,0) ; + DB_PCMN(1,"float BER : 10E-(%d/100)\n",lem->lem_float_ber,0) ; + DB_PCMN(1,"avg. BER : 10E-%d\n", + mib->fddiPORTLer_Estimate,0) ; + } + + lem->lem_errors = 0L ; + +#ifndef SLIM_SMT + cond = (mib->fddiPORTLer_Estimate <= mib->fddiPORTLer_Alarm) ? + TRUE : FALSE ; +#ifdef SMT_EXT_CUTOFF + smt_ler_alarm_check(smc,phy,cond) ; +#endif /* nSMT_EXT_CUTOFF */ + if (cond != mib->fddiPORTLerFlag) { + smt_srf_event(smc,SMT_COND_PORT_LER, + (int) (INDEX_PORT+ phy->np) ,cond) ; + } +#endif + + if ( mib->fddiPORTLer_Estimate <= mib->fddiPORTLer_Cutoff) { + phy->pc_lem_fail = TRUE ; /* flag */ + mib->fddiPORTLem_Reject_Ct++ ; + /* + * "forgive 10e-2" if we cutoff so we can come + * up again .. + */ + lem->lem_float_ber += 2*100 ; + + /*PC81b*/ +#ifdef CONCENTRATOR + DB_PCMN(1,"PCM: LER cutoff on port %d cutoff %d\n", + phy->np, mib->fddiPORTLer_Cutoff) ; +#endif +#ifdef SMT_EXT_CUTOFF + smt_port_off_event(smc,phy->np); +#else /* nSMT_EXT_CUTOFF */ + queue_event(smc,(int)(EVENT_PCM+phy->np),PC_START) ; +#endif /* nSMT_EXT_CUTOFF */ + } +} + +/* + * called by SMT to calculate LEM bit error rate + */ +void sm_lem_evaluate(struct s_smc *smc) +{ + int np ; + + for (np = 0 ; np < NUMPHYS ; np++) + lem_evaluate(smc,&smc->y[np]) ; +} + +static void lem_check_lct(struct s_smc *smc, struct s_phy *phy) +{ + struct lem_counter *lem = &phy->lem ; + struct fddi_mib_p *mib ; + int errors ; + + mib = phy->mib ; + + phy->pc_lem_fail = FALSE ; /* flag */ + errors = inpw(PLC(((int)phy->np),PL_LINK_ERR_CTR)) ; + lem->lem_errors += errors ; + mib->fddiPORTLem_Ct += errors ; + if (lem->lem_errors) { + switch(phy->lc_test) { + case LC_SHORT: + if (lem->lem_errors >= smc->s.lct_short) + phy->pc_lem_fail = TRUE ; + break ; + case LC_MEDIUM: + if (lem->lem_errors >= smc->s.lct_medium) + phy->pc_lem_fail = TRUE ; + break ; + case LC_LONG: + if (lem->lem_errors >= smc->s.lct_long) + phy->pc_lem_fail = TRUE ; + break ; + case LC_EXTENDED: + if (lem->lem_errors >= smc->s.lct_extended) + phy->pc_lem_fail = TRUE ; + break ; + } + DB_PCMN(1," >>errors : %d\n",lem->lem_errors,0) ; + } + if (phy->pc_lem_fail) { + mib->fddiPORTLCTFail_Ct++ ; + mib->fddiPORTLem_Reject_Ct++ ; + } + else + mib->fddiPORTLCTFail_Ct = 0 ; +} + +/* + * LEM functions + */ +static void sm_ph_lem_start(struct s_smc *smc, int np, int threshold) +{ + struct lem_counter *lem = &smc->y[np].lem ; + + lem->lem_on = 1 ; + lem->lem_errors = 0L ; + + /* Do NOT reset mib->fddiPORTLer_Estimate here. It is called too + * often. + */ + + outpw(PLC(np,PL_LE_THRESHOLD),threshold) ; + (void)inpw(PLC(np,PL_LINK_ERR_CTR)) ; /* clear error counter */ + + /* enable LE INT */ + SETMASK(PLC(np,PL_INTR_MASK),PL_LE_CTR,PL_LE_CTR) ; +} + +static void sm_ph_lem_stop(struct s_smc *smc, int np) +{ + struct lem_counter *lem = &smc->y[np].lem ; + + lem->lem_on = 0 ; + CLEAR(PLC(np,PL_INTR_MASK),PL_LE_CTR) ; +} + +/* ARGSUSED */ +void sm_pm_ls_latch(struct s_smc *smc, int phy, int on_off) +/* int on_off; en- or disable ident. ls */ +{ + SK_UNUSED(smc) ; + + phy = phy ; on_off = on_off ; +} + + +/* + * PCM pseudo code + * receive actions are called AFTER the bit n is received, + * i.e. if pc_rcode_actions(5) is called, bit 6 is the next bit to be received + */ + +/* + * PCM pseudo code 5.1 .. 6.1 + */ +static void pc_rcode_actions(struct s_smc *smc, int bit, struct s_phy *phy) +{ + struct fddi_mib_p *mib ; + + mib = phy->mib ; + + DB_PCMN(1,"SIG rec %x %x:\n", bit,phy->r_val[bit] ) ; + bit++ ; + + switch(bit) { + case 0: + case 1: + case 2: + break ; + case 3 : + if (phy->r_val[1] == 0 && phy->r_val[2] == 0) + mib->fddiPORTNeighborType = TA ; + else if (phy->r_val[1] == 0 && phy->r_val[2] == 1) + mib->fddiPORTNeighborType = TB ; + else if (phy->r_val[1] == 1 && phy->r_val[2] == 0) + mib->fddiPORTNeighborType = TS ; + else if (phy->r_val[1] == 1 && phy->r_val[2] == 1) + mib->fddiPORTNeighborType = TM ; + break ; + case 4: + if (mib->fddiPORTMy_Type == TM && + mib->fddiPORTNeighborType == TM) { + DB_PCMN(1,"PCM %c : E100 withhold M-M\n", + phy->phy_name,0) ; + mib->fddiPORTPC_Withhold = PC_WH_M_M ; + RS_SET(smc,RS_EVENT) ; + } + else if (phy->t_val[3] || phy->r_val[3]) { + mib->fddiPORTPC_Withhold = PC_WH_NONE ; + if (mib->fddiPORTMy_Type == TM || + mib->fddiPORTNeighborType == TM) + phy->pc_mode = PM_TREE ; + else + phy->pc_mode = PM_PEER ; + + /* reevaluate the selection criteria (wc_flag) */ + all_selection_criteria (smc); + + if (phy->wc_flag) { + mib->fddiPORTPC_Withhold = PC_WH_PATH ; + } + } + else { + mib->fddiPORTPC_Withhold = PC_WH_OTHER ; + RS_SET(smc,RS_EVENT) ; + DB_PCMN(1,"PCM %c : E101 withhold other\n", + phy->phy_name,0) ; + } + phy->twisted = ((mib->fddiPORTMy_Type != TS) && + (mib->fddiPORTMy_Type != TM) && + (mib->fddiPORTNeighborType == + mib->fddiPORTMy_Type)) ; + if (phy->twisted) { + DB_PCMN(1,"PCM %c : E102 !!! TWISTED !!!\n", + phy->phy_name,0) ; + } + break ; + case 5 : + break ; + case 6: + if (phy->t_val[4] || phy->r_val[4]) { + if ((phy->t_val[4] && phy->t_val[5]) || + (phy->r_val[4] && phy->r_val[5]) ) + phy->lc_test = LC_EXTENDED ; + else + phy->lc_test = LC_LONG ; + } + else if (phy->t_val[5] || phy->r_val[5]) + phy->lc_test = LC_MEDIUM ; + else + phy->lc_test = LC_SHORT ; + switch (phy->lc_test) { + case LC_SHORT : /* 50ms */ + outpw(PLC((int)phy->np,PL_LC_LENGTH), TP_LC_LENGTH ) ; + phy->t_next[7] = smc->s.pcm_lc_short ; + break ; + case LC_MEDIUM : /* 500ms */ + outpw(PLC((int)phy->np,PL_LC_LENGTH), TP_LC_LONGLN ) ; + phy->t_next[7] = smc->s.pcm_lc_medium ; + break ; + case LC_LONG : + SETMASK(PLC((int)phy->np,PL_CNTRL_B),PL_LONG,PL_LONG) ; + phy->t_next[7] = smc->s.pcm_lc_long ; + break ; + case LC_EXTENDED : + SETMASK(PLC((int)phy->np,PL_CNTRL_B),PL_LONG,PL_LONG) ; + phy->t_next[7] = smc->s.pcm_lc_extended ; + break ; + } + if (phy->t_next[7] > smc->s.pcm_lc_medium) { + start_pcm_timer0(smc,phy->t_next[7],PC_TIMEOUT_LCT,phy); + } + DB_PCMN(1,"LCT timer = %ld us\n", phy->t_next[7], 0) ; + phy->t_next[9] = smc->s.pcm_t_next_9 ; + break ; + case 7: + if (phy->t_val[6]) { + phy->cf_loop = TRUE ; + } + phy->td_flag = TRUE ; + break ; + case 8: + if (phy->t_val[7] || phy->r_val[7]) { + DB_PCMN(1,"PCM %c : E103 LCT fail %s\n", + phy->phy_name,phy->t_val[7]? "local":"remote") ; + queue_event(smc,(int)(EVENT_PCM+phy->np),PC_START) ; + } + break ; + case 9: + if (phy->t_val[8] || phy->r_val[8]) { + if (phy->t_val[8]) + phy->cf_loop = TRUE ; + phy->td_flag = TRUE ; + } + break ; + case 10: + if (phy->r_val[9]) { + /* neighbor intends to have MAC on output */ ; + mib->fddiPORTMacIndicated.R_val = TRUE ; + } + else { + /* neighbor does not intend to have MAC on output */ ; + mib->fddiPORTMacIndicated.R_val = FALSE ; + } + break ; + } +} + +/* + * PCM pseudo code 5.1 .. 6.1 + */ +static void pc_tcode_actions(struct s_smc *smc, const int bit, struct s_phy *phy) +{ + int np = phy->np ; + struct fddi_mib_p *mib ; + + mib = phy->mib ; + + switch(bit) { + case 0: + phy->t_val[0] = 0 ; /* no escape used */ + break ; + case 1: + if (mib->fddiPORTMy_Type == TS || mib->fddiPORTMy_Type == TM) + phy->t_val[1] = 1 ; + else + phy->t_val[1] = 0 ; + break ; + case 2 : + if (mib->fddiPORTMy_Type == TB || mib->fddiPORTMy_Type == TM) + phy->t_val[2] = 1 ; + else + phy->t_val[2] = 0 ; + break ; + case 3: + { + int type,ne ; + int policy ; + + type = mib->fddiPORTMy_Type ; + ne = mib->fddiPORTNeighborType ; + policy = smc->mib.fddiSMTConnectionPolicy ; + + phy->t_val[3] = 1 ; /* Accept connection */ + switch (type) { + case TA : + if ( + ((policy & POLICY_AA) && ne == TA) || + ((policy & POLICY_AB) && ne == TB) || + ((policy & POLICY_AS) && ne == TS) || + ((policy & POLICY_AM) && ne == TM) ) + phy->t_val[3] = 0 ; /* Reject */ + break ; + case TB : + if ( + ((policy & POLICY_BA) && ne == TA) || + ((policy & POLICY_BB) && ne == TB) || + ((policy & POLICY_BS) && ne == TS) || + ((policy & POLICY_BM) && ne == TM) ) + phy->t_val[3] = 0 ; /* Reject */ + break ; + case TS : + if ( + ((policy & POLICY_SA) && ne == TA) || + ((policy & POLICY_SB) && ne == TB) || + ((policy & POLICY_SS) && ne == TS) || + ((policy & POLICY_SM) && ne == TM) ) + phy->t_val[3] = 0 ; /* Reject */ + break ; + case TM : + if ( ne == TM || + ((policy & POLICY_MA) && ne == TA) || + ((policy & POLICY_MB) && ne == TB) || + ((policy & POLICY_MS) && ne == TS) || + ((policy & POLICY_MM) && ne == TM) ) + phy->t_val[3] = 0 ; /* Reject */ + break ; + } +#ifndef SLIM_SMT + /* + * detect undesirable connection attempt event + */ + if ( (type == TA && ne == TA ) || + (type == TA && ne == TS ) || + (type == TB && ne == TB ) || + (type == TB && ne == TS ) || + (type == TS && ne == TA ) || + (type == TS && ne == TB ) ) { + smt_srf_event(smc,SMT_EVENT_PORT_CONNECTION, + (int) (INDEX_PORT+ phy->np) ,0) ; + } +#endif + } + break ; + case 4: + if (mib->fddiPORTPC_Withhold == PC_WH_NONE) { + if (phy->pc_lem_fail) { + phy->t_val[4] = 1 ; /* long */ + phy->t_val[5] = 0 ; + } + else { + phy->t_val[4] = 0 ; + if (mib->fddiPORTLCTFail_Ct > 0) + phy->t_val[5] = 1 ; /* medium */ + else + phy->t_val[5] = 0 ; /* short */ + + /* + * Implementers choice: use medium + * instead of short when undesired + * connection attempt is made. + */ + if (phy->wc_flag) + phy->t_val[5] = 1 ; /* medium */ + } + mib->fddiPORTConnectState = PCM_CONNECTING ; + } + else { + mib->fddiPORTConnectState = PCM_STANDBY ; + phy->t_val[4] = 1 ; /* extended */ + phy->t_val[5] = 1 ; + } + break ; + case 5: + break ; + case 6: + /* we do NOT have a MAC for LCT */ + phy->t_val[6] = 0 ; + break ; + case 7: + phy->cf_loop = FALSE ; + lem_check_lct(smc,phy) ; + if (phy->pc_lem_fail) { + DB_PCMN(1,"PCM %c : E104 LCT failed\n", + phy->phy_name,0) ; + phy->t_val[7] = 1 ; + } + else + phy->t_val[7] = 0 ; + break ; + case 8: + phy->t_val[8] = 0 ; /* Don't request MAC loopback */ + break ; + case 9: + phy->cf_loop = 0 ; + if ((mib->fddiPORTPC_Withhold != PC_WH_NONE) || + ((smc->s.sas == SMT_DAS) && (phy->wc_flag))) { + queue_event(smc,EVENT_PCM+np,PC_START) ; + break ; + } + phy->t_val[9] = FALSE ; + switch (smc->s.sas) { + case SMT_DAS : + /* + * MAC intended on output + */ + if (phy->pc_mode == PM_TREE) { + if ((np == PB) || ((np == PA) && + (smc->y[PB].mib->fddiPORTConnectState != + PCM_ACTIVE))) + phy->t_val[9] = TRUE ; + } + else { + if (np == PB) + phy->t_val[9] = TRUE ; + } + break ; + case SMT_SAS : + if (np == PS) + phy->t_val[9] = TRUE ; + break ; +#ifdef CONCENTRATOR + case SMT_NAC : + /* + * MAC intended on output + */ + if (np == PB) + phy->t_val[9] = TRUE ; + break ; +#endif + } + mib->fddiPORTMacIndicated.T_val = phy->t_val[9] ; + break ; + } + DB_PCMN(1,"SIG snd %x %x:\n", bit,phy->t_val[bit] ) ; +} + +/* + * return status twisted (called by SMT) + */ +int pcm_status_twisted(struct s_smc *smc) +{ + int twist = 0 ; + if (smc->s.sas != SMT_DAS) + return 0; + if (smc->y[PA].twisted && (smc->y[PA].mib->fddiPORTPCMState == PC8_ACTIVE)) + twist |= 1 ; + if (smc->y[PB].twisted && (smc->y[PB].mib->fddiPORTPCMState == PC8_ACTIVE)) + twist |= 2 ; + return twist; +} + +/* + * return status (called by SMT) + * type + * state + * remote phy type + * remote mac yes/no + */ +void pcm_status_state(struct s_smc *smc, int np, int *type, int *state, + int *remote, int *mac) +{ + struct s_phy *phy = &smc->y[np] ; + struct fddi_mib_p *mib ; + + mib = phy->mib ; + + /* remote PHY type and MAC - set only if active */ + *mac = 0 ; + *type = mib->fddiPORTMy_Type ; /* our PHY type */ + *state = mib->fddiPORTConnectState ; + *remote = mib->fddiPORTNeighborType ; + + switch(mib->fddiPORTPCMState) { + case PC8_ACTIVE : + *mac = mib->fddiPORTMacIndicated.R_val ; + break ; + } +} + +/* + * return rooted station status (called by SMT) + */ +int pcm_rooted_station(struct s_smc *smc) +{ + int n ; + + for (n = 0 ; n < NUMPHYS ; n++) { + if (smc->y[n].mib->fddiPORTPCMState == PC8_ACTIVE && + smc->y[n].mib->fddiPORTNeighborType == TM) + return 0; + } + return 1; +} + +/* + * Interrupt actions for PLC & PCM events + */ +void plc_irq(struct s_smc *smc, int np, unsigned int cmd) +/* int np; PHY index */ +{ + struct s_phy *phy = &smc->y[np] ; + struct s_plc *plc = &phy->plc ; + int n ; +#ifdef SUPERNET_3 + int corr_mask ; +#endif /* SUPERNET_3 */ + int i ; + + if (np >= smc->s.numphys) { + plc->soft_err++ ; + return ; + } + if (cmd & PL_EBUF_ERR) { /* elastic buff. det. over-|underflow*/ + /* + * Check whether the SRF Condition occurred. + */ + if (!plc->ebuf_cont && phy->mib->fddiPORTPCMState == PC8_ACTIVE){ + /* + * This is the real Elasticity Error. + * More than one in a row are treated as a + * single one. + * Only count this in the active state. + */ + phy->mib->fddiPORTEBError_Ct ++ ; + + } + + plc->ebuf_err++ ; + if (plc->ebuf_cont <= 1000) { + /* + * Prevent counter from being wrapped after + * hanging years in that interrupt. + */ + plc->ebuf_cont++ ; /* Ebuf continuous error */ + } + +#ifdef SUPERNET_3 + if (plc->ebuf_cont == 1000 && + ((inpw(PLC(np,PL_STATUS_A)) & PLC_REV_MASK) == + PLC_REV_SN3)) { + /* + * This interrupt remeained high for at least + * 1000 consecutive interrupt calls. + * + * This is caused by a hardware error of the + * ORION part of the Supernet III chipset. + * + * Disable this bit from the mask. + */ + corr_mask = (plc_imsk_na & ~PL_EBUF_ERR) ; + outpw(PLC(np,PL_INTR_MASK),corr_mask); + + /* + * Disconnect from the ring. + * Call the driver with the reset indication. + */ + queue_event(smc,EVENT_ECM,EC_DISCONNECT) ; + + /* + * Make an error log entry. + */ + SMT_ERR_LOG(smc,SMT_E0136, SMT_E0136_MSG) ; + + /* + * Indicate the Reset. + */ + drv_reset_indication(smc) ; + } +#endif /* SUPERNET_3 */ + } else { + /* Reset the continuous error variable */ + plc->ebuf_cont = 0 ; /* reset Ebuf continuous error */ + } + if (cmd & PL_PHYINV) { /* physical layer invalid signal */ + plc->phyinv++ ; + } + if (cmd & PL_VSYM_CTR) { /* violation symbol counter has incr.*/ + plc->vsym_ctr++ ; + } + if (cmd & PL_MINI_CTR) { /* dep. on PLC_CNTRL_A's MINI_CTR_INT*/ + plc->mini_ctr++ ; + } + if (cmd & PL_LE_CTR) { /* link error event counter */ + int j ; + + /* + * note: PL_LINK_ERR_CTR MUST be read to clear it + */ + j = inpw(PLC(np,PL_LE_THRESHOLD)) ; + i = inpw(PLC(np,PL_LINK_ERR_CTR)) ; + + if (i < j) { + /* wrapped around */ + i += 256 ; + } + + if (phy->lem.lem_on) { + /* Note: Lem errors shall only be counted when + * link is ACTIVE or LCT is active. + */ + phy->lem.lem_errors += i ; + phy->mib->fddiPORTLem_Ct += i ; + } + } + if (cmd & PL_TPC_EXPIRED) { /* TPC timer reached zero */ + if (plc->p_state == PS_LCT) { + /* + * end of LCT + */ + ; + } + plc->tpc_exp++ ; + } + if (cmd & PL_LS_MATCH) { /* LS == LS in PLC_CNTRL_B's MATCH_LS*/ + switch (inpw(PLC(np,PL_CNTRL_B)) & PL_MATCH_LS) { + case PL_I_IDLE : phy->curr_ls = PC_ILS ; break ; + case PL_I_HALT : phy->curr_ls = PC_HLS ; break ; + case PL_I_MASTR : phy->curr_ls = PC_MLS ; break ; + case PL_I_QUIET : phy->curr_ls = PC_QLS ; break ; + } + } + if (cmd & PL_PCM_BREAK) { /* PCM has entered the BREAK state */ + int reason; + + reason = inpw(PLC(np,PL_STATUS_B)) & PL_BREAK_REASON ; + + switch (reason) { + case PL_B_PCS : plc->b_pcs++ ; break ; + case PL_B_TPC : plc->b_tpc++ ; break ; + case PL_B_TNE : plc->b_tne++ ; break ; + case PL_B_QLS : plc->b_qls++ ; break ; + case PL_B_ILS : plc->b_ils++ ; break ; + case PL_B_HLS : plc->b_hls++ ; break ; + } + + /*jd 05-Aug-1999 changed: Bug #10419 */ + DB_PCMN(1,"PLC %d: MDcF = %x\n", np, smc->e.DisconnectFlag); + if (smc->e.DisconnectFlag == FALSE) { + DB_PCMN(1,"PLC %d: restart (reason %x)\n", np, reason); + queue_event(smc,EVENT_PCM+np,PC_START) ; + } + else { + DB_PCMN(1,"PLC %d: NO!! restart (reason %x)\n", np, reason); + } + return ; + } + /* + * If both CODE & ENABLE are set ignore enable + */ + if (cmd & PL_PCM_CODE) { /* receive last sign.-bit | LCT complete */ + queue_event(smc,EVENT_PCM+np,PC_SIGNAL) ; + n = inpw(PLC(np,PL_RCV_VECTOR)) ; + for (i = 0 ; i < plc->p_bits ; i++) { + phy->r_val[plc->p_start+i] = n & 1 ; + n >>= 1 ; + } + } + else if (cmd & PL_PCM_ENABLED) { /* asserted SC_JOIN, scrub.completed*/ + queue_event(smc,EVENT_PCM+np,PC_JOIN) ; + } + if (cmd & PL_TRACE_PROP) { /* MLS while PC8_ACTIV || PC2_TRACE */ + /*PC22b*/ + if (!phy->tr_flag) { + DB_PCMN(1,"PCM : irq TRACE_PROP %d %d\n", + np,smc->mib.fddiSMTECMState) ; + phy->tr_flag = TRUE ; + smc->e.trace_prop |= ENTITY_BIT(ENTITY_PHY(np)) ; + queue_event(smc,EVENT_ECM,EC_TRACE_PROP) ; + } + } + /* + * filter PLC glitch ??? + * QLS || HLS only while in PC2_TRACE state + */ + if ((cmd & PL_SELF_TEST) && (phy->mib->fddiPORTPCMState == PC2_TRACE)) { + /*PC22a*/ + if (smc->e.path_test == PT_PASSED) { + DB_PCMN(1,"PCM : state = %s %d\n", get_pcmstate(smc,np), + phy->mib->fddiPORTPCMState) ; + + smc->e.path_test = PT_PENDING ; + queue_event(smc,EVENT_ECM,EC_PATH_TEST) ; + } + } + if (cmd & PL_TNE_EXPIRED) { /* TNE: length of noise events */ + /* break_required (TNE > NS_Max) */ + if (phy->mib->fddiPORTPCMState == PC8_ACTIVE) { + if (!phy->tr_flag) { + DB_PCMN(1,"PCM %c : PC81 %s\n",phy->phy_name,"NSE"); + queue_event(smc,EVENT_PCM+np,PC_START) ; + return ; + } + } + } +#if 0 + if (cmd & PL_NP_ERR) { /* NP has requested to r/w an inv reg*/ + /* + * It's a bug by AMD + */ + plc->np_err++ ; + } + /* pin inactiv (GND) */ + if (cmd & PL_PARITY_ERR) { /* p. error dedected on TX9-0 inp */ + plc->parity_err++ ; + } + if (cmd & PL_LSDO) { /* carrier detected */ + ; + } +#endif +} + +#ifdef DEBUG +/* + * fill state struct + */ +void pcm_get_state(struct s_smc *smc, struct smt_state *state) +{ + struct s_phy *phy ; + struct pcm_state *pcs ; + int i ; + int ii ; + short rbits ; + short tbits ; + struct fddi_mib_p *mib ; + + for (i = 0, phy = smc->y, pcs = state->pcm_state ; i < NUMPHYS ; + i++ , phy++, pcs++ ) { + mib = phy->mib ; + pcs->pcm_type = (u_char) mib->fddiPORTMy_Type ; + pcs->pcm_state = (u_char) mib->fddiPORTPCMState ; + pcs->pcm_mode = phy->pc_mode ; + pcs->pcm_neighbor = (u_char) mib->fddiPORTNeighborType ; + pcs->pcm_bsf = mib->fddiPORTBS_Flag ; + pcs->pcm_lsf = phy->ls_flag ; + pcs->pcm_lct_fail = (u_char) mib->fddiPORTLCTFail_Ct ; + pcs->pcm_ls_rx = LS2MIB(sm_pm_get_ls(smc,i)) ; + for (ii = 0, rbits = tbits = 0 ; ii < NUMBITS ; ii++) { + rbits <<= 1 ; + tbits <<= 1 ; + if (phy->r_val[NUMBITS-1-ii]) + rbits |= 1 ; + if (phy->t_val[NUMBITS-1-ii]) + tbits |= 1 ; + } + pcs->pcm_r_val = rbits ; + pcs->pcm_t_val = tbits ; + } +} + +int get_pcm_state(struct s_smc *smc, int np) +{ + int pcs ; + + SK_UNUSED(smc) ; + + switch (inpw(PLC(np,PL_STATUS_B)) & PL_PCM_STATE) { + case PL_PC0 : pcs = PC_STOP ; break ; + case PL_PC1 : pcs = PC_START ; break ; + case PL_PC2 : pcs = PC_TRACE ; break ; + case PL_PC3 : pcs = PC_SIGNAL ; break ; + case PL_PC4 : pcs = PC_SIGNAL ; break ; + case PL_PC5 : pcs = PC_SIGNAL ; break ; + case PL_PC6 : pcs = PC_JOIN ; break ; + case PL_PC7 : pcs = PC_JOIN ; break ; + case PL_PC8 : pcs = PC_ENABLE ; break ; + case PL_PC9 : pcs = PC_MAINT ; break ; + default : pcs = PC_DISABLE ; break ; + } + return pcs; +} + +char *get_linestate(struct s_smc *smc, int np) +{ + char *ls = "" ; + + SK_UNUSED(smc) ; + + switch (inpw(PLC(np,PL_STATUS_A)) & PL_LINE_ST) { + case PL_L_NLS : ls = "NOISE" ; break ; + case PL_L_ALS : ls = "ACTIV" ; break ; + case PL_L_UND : ls = "UNDEF" ; break ; + case PL_L_ILS4: ls = "ILS 4" ; break ; + case PL_L_QLS : ls = "QLS" ; break ; + case PL_L_MLS : ls = "MLS" ; break ; + case PL_L_HLS : ls = "HLS" ; break ; + case PL_L_ILS16:ls = "ILS16" ; break ; +#ifdef lint + default: ls = "unknown" ; break ; +#endif + } + return ls; +} + +char *get_pcmstate(struct s_smc *smc, int np) +{ + char *pcs ; + + SK_UNUSED(smc) ; + + switch (inpw(PLC(np,PL_STATUS_B)) & PL_PCM_STATE) { + case PL_PC0 : pcs = "OFF" ; break ; + case PL_PC1 : pcs = "BREAK" ; break ; + case PL_PC2 : pcs = "TRACE" ; break ; + case PL_PC3 : pcs = "CONNECT"; break ; + case PL_PC4 : pcs = "NEXT" ; break ; + case PL_PC5 : pcs = "SIGNAL" ; break ; + case PL_PC6 : pcs = "JOIN" ; break ; + case PL_PC7 : pcs = "VERIFY" ; break ; + case PL_PC8 : pcs = "ACTIV" ; break ; + case PL_PC9 : pcs = "MAINT" ; break ; + default : pcs = "UNKNOWN" ; break ; + } + return pcs; +} + +void list_phy(struct s_smc *smc) +{ + struct s_plc *plc ; + int np ; + + for (np = 0 ; np < NUMPHYS ; np++) { + plc = &smc->y[np].plc ; + printf("PHY %d:\tERRORS\t\t\tBREAK_REASONS\t\tSTATES:\n",np) ; + printf("\tsoft_error: %ld \t\tPC_Start : %ld\n", + plc->soft_err,plc->b_pcs); + printf("\tparity_err: %ld \t\tTPC exp. : %ld\t\tLine: %s\n", + plc->parity_err,plc->b_tpc,get_linestate(smc,np)) ; + printf("\tebuf_error: %ld \t\tTNE exp. : %ld\n", + plc->ebuf_err,plc->b_tne) ; + printf("\tphyinvalid: %ld \t\tQLS det. : %ld\t\tPCM : %s\n", + plc->phyinv,plc->b_qls,get_pcmstate(smc,np)) ; + printf("\tviosym_ctr: %ld \t\tILS det. : %ld\n", + plc->vsym_ctr,plc->b_ils) ; + printf("\tmingap_ctr: %ld \t\tHLS det. : %ld\n", + plc->mini_ctr,plc->b_hls) ; + printf("\tnodepr_err: %ld\n",plc->np_err) ; + printf("\tTPC_exp : %ld\n",plc->tpc_exp) ; + printf("\tLEM_err : %ld\n",smc->y[np].lem.lem_errors) ; + } +} + + +#ifdef CONCENTRATOR +void pcm_lem_dump(struct s_smc *smc) +{ + int i ; + struct s_phy *phy ; + struct fddi_mib_p *mib ; + + char *entostring() ; + + printf("PHY errors BER\n") ; + printf("----------------------\n") ; + for (i = 0,phy = smc->y ; i < NUMPHYS ; i++,phy++) { + if (!plc_is_installed(smc,i)) + continue ; + mib = phy->mib ; + printf("%s\t%ld\t10E-%d\n", + entostring(smc,ENTITY_PHY(i)), + mib->fddiPORTLem_Ct, + mib->fddiPORTLer_Estimate) ; + } +} +#endif +#endif diff --git a/kernel/drivers/net/fddi/skfp/pmf.c b/kernel/drivers/net/fddi/skfp/pmf.c new file mode 100644 index 000000000..441b4dc79 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/pmf.c @@ -0,0 +1,1663 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + Parameter Management Frame processing for SMT 7.2 +*/ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/smt_p.h" + +#define KERNEL +#include "h/smtstate.h" + +#ifndef SLIM_SMT + +#ifndef lint +static const char ID_sccs[] = "@(#)pmf.c 1.37 97/08/04 (C) SK " ; +#endif + +static int smt_authorize(struct s_smc *smc, struct smt_header *sm); +static int smt_check_set_count(struct s_smc *smc, struct smt_header *sm); +static const struct s_p_tab* smt_get_ptab(u_short para); +static int smt_mib_phys(struct s_smc *smc); +static int smt_set_para(struct s_smc *smc, struct smt_para *pa, int index, + int local, int set); +void smt_add_para(struct s_smc *smc, struct s_pcon *pcon, u_short para, + int index, int local); +static SMbuf *smt_build_pmf_response(struct s_smc *smc, struct smt_header *req, + int set, int local); +static int port_to_mib(struct s_smc *smc, int p); + +#define MOFFSS(e) offsetof(struct fddi_mib, e) +#define MOFFMS(e) offsetof(struct fddi_mib_m, e) +#define MOFFAS(e) offsetof(struct fddi_mib_a, e) +#define MOFFPS(e) offsetof(struct fddi_mib_p, e) + + +#define AC_G 0x01 /* Get */ +#define AC_GR 0x02 /* Get/Set */ +#define AC_S 0x04 /* Set */ +#define AC_NA 0x08 +#define AC_GROUP 0x10 /* Group */ +#define MS2BCLK(x) ((x)*12500L) +/* + F LFag (byte) + B byte + S u_short 16 bit + C Counter 32 bit + L Long 32 bit + T Timer_2 32 bit + P TimeStamp ; + A LongAddress (6 byte) + E Enum 16 bit + R ResId 16 Bit +*/ +static const struct s_p_tab { + u_short p_num ; /* parameter code */ + u_char p_access ; /* access rights */ + u_short p_offset ; /* offset in mib */ + char p_swap[3] ; /* format string */ +} p_tab[] = { + /* StationIdGrp */ + { SMT_P100A,AC_GROUP } , + { SMT_P100B,AC_G, MOFFSS(fddiSMTStationId), "8" } , + { SMT_P100D,AC_G, MOFFSS(fddiSMTOpVersionId), "S" } , + { SMT_P100E,AC_G, MOFFSS(fddiSMTHiVersionId), "S" } , + { SMT_P100F,AC_G, MOFFSS(fddiSMTLoVersionId), "S" } , + { SMT_P1010,AC_G, MOFFSS(fddiSMTManufacturerData), "D" } , + { SMT_P1011,AC_GR, MOFFSS(fddiSMTUserData), "D" } , + { SMT_P1012,AC_G, MOFFSS(fddiSMTMIBVersionId), "S" } , + + /* StationConfigGrp */ + { SMT_P1014,AC_GROUP } , + { SMT_P1015,AC_G, MOFFSS(fddiSMTMac_Ct), "B" } , + { SMT_P1016,AC_G, MOFFSS(fddiSMTNonMaster_Ct), "B" } , + { SMT_P1017,AC_G, MOFFSS(fddiSMTMaster_Ct), "B" } , + { SMT_P1018,AC_G, MOFFSS(fddiSMTAvailablePaths), "B" } , + { SMT_P1019,AC_G, MOFFSS(fddiSMTConfigCapabilities),"S" } , + { SMT_P101A,AC_GR, MOFFSS(fddiSMTConfigPolicy), "wS" } , + { SMT_P101B,AC_GR, MOFFSS(fddiSMTConnectionPolicy),"wS" } , + { SMT_P101D,AC_GR, MOFFSS(fddiSMTTT_Notify), "wS" } , + { SMT_P101E,AC_GR, MOFFSS(fddiSMTStatRptPolicy), "bB" } , + { SMT_P101F,AC_GR, MOFFSS(fddiSMTTrace_MaxExpiration),"lL" } , + { SMT_P1020,AC_G, MOFFSS(fddiSMTPORTIndexes), "II" } , + { SMT_P1021,AC_G, MOFFSS(fddiSMTMACIndexes), "I" } , + { SMT_P1022,AC_G, MOFFSS(fddiSMTBypassPresent), "F" } , + + /* StatusGrp */ + { SMT_P1028,AC_GROUP } , + { SMT_P1029,AC_G, MOFFSS(fddiSMTECMState), "E" } , + { SMT_P102A,AC_G, MOFFSS(fddiSMTCF_State), "E" } , + { SMT_P102C,AC_G, MOFFSS(fddiSMTRemoteDisconnectFlag),"F" } , + { SMT_P102D,AC_G, MOFFSS(fddiSMTStationStatus), "E" } , + { SMT_P102E,AC_G, MOFFSS(fddiSMTPeerWrapFlag), "F" } , + + /* MIBOperationGrp */ + { SMT_P1032,AC_GROUP } , + { SMT_P1033,AC_G, MOFFSS(fddiSMTTimeStamp),"P" } , + { SMT_P1034,AC_G, MOFFSS(fddiSMTTransitionTimeStamp),"P" } , + /* NOTE : SMT_P1035 is already swapped ! SMT_P_SETCOUNT */ + { SMT_P1035,AC_G, MOFFSS(fddiSMTSetCount),"4P" } , + { SMT_P1036,AC_G, MOFFSS(fddiSMTLastSetStationId),"8" } , + + { SMT_P103C,AC_S, 0, "wS" } , + + /* + * PRIVATE EXTENSIONS + * only accessible locally to get/set passwd + */ + { SMT_P10F0,AC_GR, MOFFSS(fddiPRPMFPasswd), "8" } , + { SMT_P10F1,AC_GR, MOFFSS(fddiPRPMFStation), "8" } , +#ifdef ESS + { SMT_P10F2,AC_GR, MOFFSS(fddiESSPayload), "lL" } , + { SMT_P10F3,AC_GR, MOFFSS(fddiESSOverhead), "lL" } , + { SMT_P10F4,AC_GR, MOFFSS(fddiESSMaxTNeg), "lL" } , + { SMT_P10F5,AC_GR, MOFFSS(fddiESSMinSegmentSize), "lL" } , + { SMT_P10F6,AC_GR, MOFFSS(fddiESSCategory), "lL" } , + { SMT_P10F7,AC_GR, MOFFSS(fddiESSSynchTxMode), "wS" } , +#endif +#ifdef SBA + { SMT_P10F8,AC_GR, MOFFSS(fddiSBACommand), "bF" } , + { SMT_P10F9,AC_GR, MOFFSS(fddiSBAAvailable), "bF" } , +#endif + /* MAC Attributes */ + { SMT_P200A,AC_GROUP } , + { SMT_P200B,AC_G, MOFFMS(fddiMACFrameStatusFunctions),"S" } , + { SMT_P200D,AC_G, MOFFMS(fddiMACT_MaxCapabilitiy),"T" } , + { SMT_P200E,AC_G, MOFFMS(fddiMACTVXCapabilitiy),"T" } , + + /* ConfigGrp */ + { SMT_P2014,AC_GROUP } , + { SMT_P2016,AC_G, MOFFMS(fddiMACAvailablePaths), "B" } , + { SMT_P2017,AC_G, MOFFMS(fddiMACCurrentPath), "S" } , + { SMT_P2018,AC_G, MOFFMS(fddiMACUpstreamNbr), "A" } , + { SMT_P2019,AC_G, MOFFMS(fddiMACDownstreamNbr), "A" } , + { SMT_P201A,AC_G, MOFFMS(fddiMACOldUpstreamNbr), "A" } , + { SMT_P201B,AC_G, MOFFMS(fddiMACOldDownstreamNbr),"A" } , + { SMT_P201D,AC_G, MOFFMS(fddiMACDupAddressTest), "E" } , + { SMT_P2020,AC_GR, MOFFMS(fddiMACRequestedPaths), "wS" } , + { SMT_P2021,AC_G, MOFFMS(fddiMACDownstreamPORTType),"E" } , + { SMT_P2022,AC_G, MOFFMS(fddiMACIndex), "S" } , + + /* AddressGrp */ + { SMT_P2028,AC_GROUP } , + { SMT_P2029,AC_G, MOFFMS(fddiMACSMTAddress), "A" } , + + /* OperationGrp */ + { SMT_P2032,AC_GROUP } , + { SMT_P2033,AC_G, MOFFMS(fddiMACT_Req), "T" } , + { SMT_P2034,AC_G, MOFFMS(fddiMACT_Neg), "T" } , + { SMT_P2035,AC_G, MOFFMS(fddiMACT_Max), "T" } , + { SMT_P2036,AC_G, MOFFMS(fddiMACTvxValue), "T" } , + { SMT_P2038,AC_G, MOFFMS(fddiMACT_Pri0), "T" } , + { SMT_P2039,AC_G, MOFFMS(fddiMACT_Pri1), "T" } , + { SMT_P203A,AC_G, MOFFMS(fddiMACT_Pri2), "T" } , + { SMT_P203B,AC_G, MOFFMS(fddiMACT_Pri3), "T" } , + { SMT_P203C,AC_G, MOFFMS(fddiMACT_Pri4), "T" } , + { SMT_P203D,AC_G, MOFFMS(fddiMACT_Pri5), "T" } , + { SMT_P203E,AC_G, MOFFMS(fddiMACT_Pri6), "T" } , + + + /* CountersGrp */ + { SMT_P2046,AC_GROUP } , + { SMT_P2047,AC_G, MOFFMS(fddiMACFrame_Ct), "C" } , + { SMT_P2048,AC_G, MOFFMS(fddiMACCopied_Ct), "C" } , + { SMT_P2049,AC_G, MOFFMS(fddiMACTransmit_Ct), "C" } , + { SMT_P204A,AC_G, MOFFMS(fddiMACToken_Ct), "C" } , + { SMT_P2051,AC_G, MOFFMS(fddiMACError_Ct), "C" } , + { SMT_P2052,AC_G, MOFFMS(fddiMACLost_Ct), "C" } , + { SMT_P2053,AC_G, MOFFMS(fddiMACTvxExpired_Ct), "C" } , + { SMT_P2054,AC_G, MOFFMS(fddiMACNotCopied_Ct), "C" } , + { SMT_P2056,AC_G, MOFFMS(fddiMACRingOp_Ct), "C" } , + + /* FrameErrorConditionGrp */ + { SMT_P205A,AC_GROUP } , + { SMT_P205F,AC_GR, MOFFMS(fddiMACFrameErrorThreshold),"wS" } , + { SMT_P2060,AC_G, MOFFMS(fddiMACFrameErrorRatio), "S" } , + + /* NotCopiedConditionGrp */ + { SMT_P2064,AC_GROUP } , + { SMT_P2067,AC_GR, MOFFMS(fddiMACNotCopiedThreshold),"wS" } , + { SMT_P2069,AC_G, MOFFMS(fddiMACNotCopiedRatio), "S" } , + + /* StatusGrp */ + { SMT_P206E,AC_GROUP } , + { SMT_P206F,AC_G, MOFFMS(fddiMACRMTState), "S" } , + { SMT_P2070,AC_G, MOFFMS(fddiMACDA_Flag), "F" } , + { SMT_P2071,AC_G, MOFFMS(fddiMACUNDA_Flag), "F" } , + { SMT_P2072,AC_G, MOFFMS(fddiMACFrameErrorFlag), "F" } , + { SMT_P2073,AC_G, MOFFMS(fddiMACNotCopiedFlag), "F" } , + { SMT_P2074,AC_G, MOFFMS(fddiMACMA_UnitdataAvailable),"F" } , + { SMT_P2075,AC_G, MOFFMS(fddiMACHardwarePresent), "F" } , + { SMT_P2076,AC_GR, MOFFMS(fddiMACMA_UnitdataEnable),"bF" } , + + /* + * PRIVATE EXTENSIONS + * only accessible locally to get/set TMIN + */ + { SMT_P20F0,AC_NA } , + { SMT_P20F1,AC_GR, MOFFMS(fddiMACT_Min), "lT" } , + + /* Path Attributes */ + /* + * DON't swap 320B,320F,3210: they are already swapped in swap_para() + */ + { SMT_P320A,AC_GROUP } , + { SMT_P320B,AC_G, MOFFAS(fddiPATHIndex), "r" } , + { SMT_P320F,AC_GR, MOFFAS(fddiPATHSbaPayload), "l4" } , + { SMT_P3210,AC_GR, MOFFAS(fddiPATHSbaOverhead), "l4" } , + /* fddiPATHConfiguration */ + { SMT_P3212,AC_G, 0, "" } , + { SMT_P3213,AC_GR, MOFFAS(fddiPATHT_Rmode), "lT" } , + { SMT_P3214,AC_GR, MOFFAS(fddiPATHSbaAvailable), "lL" } , + { SMT_P3215,AC_GR, MOFFAS(fddiPATHTVXLowerBound), "lT" } , + { SMT_P3216,AC_GR, MOFFAS(fddiPATHT_MaxLowerBound),"lT" } , + { SMT_P3217,AC_GR, MOFFAS(fddiPATHMaxT_Req), "lT" } , + + /* Port Attributes */ + /* ConfigGrp */ + { SMT_P400A,AC_GROUP } , + { SMT_P400C,AC_G, MOFFPS(fddiPORTMy_Type), "E" } , + { SMT_P400D,AC_G, MOFFPS(fddiPORTNeighborType), "E" } , + { SMT_P400E,AC_GR, MOFFPS(fddiPORTConnectionPolicies),"bB" } , + { SMT_P400F,AC_G, MOFFPS(fddiPORTMacIndicated), "2" } , + { SMT_P4010,AC_G, MOFFPS(fddiPORTCurrentPath), "E" } , + { SMT_P4011,AC_GR, MOFFPS(fddiPORTRequestedPaths), "l4" } , + { SMT_P4012,AC_G, MOFFPS(fddiPORTMACPlacement), "S" } , + { SMT_P4013,AC_G, MOFFPS(fddiPORTAvailablePaths), "B" } , + { SMT_P4016,AC_G, MOFFPS(fddiPORTPMDClass), "E" } , + { SMT_P4017,AC_G, MOFFPS(fddiPORTConnectionCapabilities), "B"} , + { SMT_P401D,AC_G, MOFFPS(fddiPORTIndex), "R" } , + + /* OperationGrp */ + { SMT_P401E,AC_GROUP } , + { SMT_P401F,AC_GR, MOFFPS(fddiPORTMaint_LS), "wE" } , + { SMT_P4021,AC_G, MOFFPS(fddiPORTBS_Flag), "F" } , + { SMT_P4022,AC_G, MOFFPS(fddiPORTPC_LS), "E" } , + + /* ErrorCtrsGrp */ + { SMT_P4028,AC_GROUP } , + { SMT_P4029,AC_G, MOFFPS(fddiPORTEBError_Ct), "C" } , + { SMT_P402A,AC_G, MOFFPS(fddiPORTLCTFail_Ct), "C" } , + + /* LerGrp */ + { SMT_P4032,AC_GROUP } , + { SMT_P4033,AC_G, MOFFPS(fddiPORTLer_Estimate), "F" } , + { SMT_P4034,AC_G, MOFFPS(fddiPORTLem_Reject_Ct), "C" } , + { SMT_P4035,AC_G, MOFFPS(fddiPORTLem_Ct), "C" } , + { SMT_P403A,AC_GR, MOFFPS(fddiPORTLer_Cutoff), "bB" } , + { SMT_P403B,AC_GR, MOFFPS(fddiPORTLer_Alarm), "bB" } , + + /* StatusGrp */ + { SMT_P403C,AC_GROUP } , + { SMT_P403D,AC_G, MOFFPS(fddiPORTConnectState), "E" } , + { SMT_P403E,AC_G, MOFFPS(fddiPORTPCMStateX), "E" } , + { SMT_P403F,AC_G, MOFFPS(fddiPORTPC_Withhold), "E" } , + { SMT_P4040,AC_G, MOFFPS(fddiPORTLerFlag), "F" } , + { SMT_P4041,AC_G, MOFFPS(fddiPORTHardwarePresent),"F" } , + + { SMT_P4046,AC_S, 0, "wS" } , + + { 0, AC_GROUP } , + { 0 } +} ; + +void smt_pmf_received_pack(struct s_smc *smc, SMbuf *mb, int local) +{ + struct smt_header *sm ; + SMbuf *reply ; + + sm = smtod(mb,struct smt_header *) ; + DB_SMT("SMT: processing PMF frame at %x len %d\n",sm,mb->sm_len) ; +#ifdef DEBUG + dump_smt(smc,sm,"PMF Received") ; +#endif + /* + * Start the watchdog: It may be a long, long packet and + * maybe the watchdog occurs ... + */ + smt_start_watchdog(smc) ; + + if (sm->smt_class == SMT_PMF_GET || + sm->smt_class == SMT_PMF_SET) { + reply = smt_build_pmf_response(smc,sm, + sm->smt_class == SMT_PMF_SET,local) ; + if (reply) { + sm = smtod(reply,struct smt_header *) ; +#ifdef DEBUG + dump_smt(smc,sm,"PMF Reply") ; +#endif + smt_send_frame(smc,reply,FC_SMT_INFO,local) ; + } + } +} + +static SMbuf *smt_build_pmf_response(struct s_smc *smc, struct smt_header *req, + int set, int local) +{ + SMbuf *mb ; + struct smt_header *smt ; + struct smt_para *pa ; + struct smt_p_reason *res ; + const struct s_p_tab *pt ; + int len ; + int index ; + int idx_end ; + int error ; + int range ; + SK_LOC_DECL(struct s_pcon,pcon) ; + SK_LOC_DECL(struct s_pcon,set_pcon) ; + + /* + * build SMT header + */ + if (!(mb = smt_get_mbuf(smc))) + return mb; + + smt = smtod(mb, struct smt_header *) ; + smt->smt_dest = req->smt_source ; /* DA == source of request */ + smt->smt_class = req->smt_class ; /* same class (GET/SET) */ + smt->smt_type = SMT_REPLY ; + smt->smt_version = SMT_VID_2 ; + smt->smt_tid = req->smt_tid ; /* same TID */ + smt->smt_pad = 0 ; + smt->smt_len = 0 ; + + /* + * setup parameter status + */ + pcon.pc_len = SMT_MAX_INFO_LEN ; /* max para length */ + pcon.pc_err = 0 ; /* no error */ + pcon.pc_badset = 0 ; /* no bad set count */ + pcon.pc_p = (void *) (smt + 1) ; /* paras start here */ + + /* + * check authoriziation and set count + */ + error = 0 ; + if (set) { + if (!local && smt_authorize(smc,req)) + error = SMT_RDF_AUTHOR ; + else if (smt_check_set_count(smc,req)) + pcon.pc_badset = SMT_RDF_BADSET ; + } + /* + * add reason code and all mandatory parameters + */ + res = (struct smt_p_reason *) pcon.pc_p ; + smt_add_para(smc,&pcon,(u_short) SMT_P_REASON,0,0) ; + smt_add_para(smc,&pcon,(u_short) SMT_P1033,0,0) ; + /* update 1035 and 1036 later if set */ + set_pcon = pcon ; + smt_add_para(smc,&pcon,(u_short) SMT_P1035,0,0) ; + smt_add_para(smc,&pcon,(u_short) SMT_P1036,0,0) ; + + pcon.pc_err = error ; + len = req->smt_len ; + pa = (struct smt_para *) (req + 1) ; + /* + * process list of paras + */ + while (!pcon.pc_err && len > 0 ) { + if (((u_short)len < pa->p_len + PARA_LEN) || (pa->p_len & 3)) { + pcon.pc_err = SMT_RDF_LENGTH ; + break ; + } + + if (((range = (pa->p_type & 0xf000)) == 0x2000) || + range == 0x3000 || range == 0x4000) { + /* + * get index for PART,MAC ad PATH group + */ + index = *((u_char *)pa + PARA_LEN + 3) ;/* index */ + idx_end = index ; + if (!set && (pa->p_len != 4)) { + pcon.pc_err = SMT_RDF_LENGTH ; + break ; + } + if (!index && !set) { + switch (range) { + case 0x2000 : + index = INDEX_MAC ; + idx_end = index - 1 + NUMMACS ; + break ; + case 0x3000 : + index = INDEX_PATH ; + idx_end = index - 1 + NUMPATHS ; + break ; + case 0x4000 : + index = INDEX_PORT ; + idx_end = index - 1 + NUMPHYS ; +#ifndef CONCENTRATOR + if (smc->s.sas == SMT_SAS) + idx_end = INDEX_PORT ; +#endif + break ; + } + } + } + else { + /* + * smt group has no index + */ + if (!set && (pa->p_len != 0)) { + pcon.pc_err = SMT_RDF_LENGTH ; + break ; + } + index = 0 ; + idx_end = 0 ; + } + while (index <= idx_end) { + /* + * if group + * add all paras of group + */ + pt = smt_get_ptab(pa->p_type) ; + if (pt && pt->p_access == AC_GROUP && !set) { + pt++ ; + while (pt->p_access == AC_G || + pt->p_access == AC_GR) { + smt_add_para(smc,&pcon,pt->p_num, + index,local); + pt++ ; + } + } + /* + * ignore + * AUTHORIZATION in get/set + * SET COUNT in set + */ + else if (pa->p_type != SMT_P_AUTHOR && + (!set || (pa->p_type != SMT_P1035))) { + int st ; + if (pcon.pc_badset) { + smt_add_para(smc,&pcon,pa->p_type, + index,local) ; + } + else if (set) { + st = smt_set_para(smc,pa,index,local,1); + /* + * return para even if error + */ + smt_add_para(smc,&pcon,pa->p_type, + index,local) ; + pcon.pc_err = st ; + } + else { + if (pt && pt->p_access == AC_S) { + pcon.pc_err = + SMT_RDF_ILLEGAL ; + } + smt_add_para(smc,&pcon,pa->p_type, + index,local) ; + } + } + if (pcon.pc_err) + break ; + index++ ; + } + len -= pa->p_len + PARA_LEN ; + pa = (struct smt_para *) ((char *)pa + pa->p_len + PARA_LEN) ; + } + smt->smt_len = SMT_MAX_INFO_LEN - pcon.pc_len ; + mb->sm_len = smt->smt_len + sizeof(struct smt_header) ; + + /* update reason code */ + res->rdf_reason = pcon.pc_badset ? pcon.pc_badset : + pcon.pc_err ? pcon.pc_err : SMT_RDF_SUCCESS ; + if (set && (res->rdf_reason == SMT_RDF_SUCCESS)) { + /* + * increment set count + * set time stamp + * store station id of last set + */ + smc->mib.fddiSMTSetCount.count++ ; + smt_set_timestamp(smc,smc->mib.fddiSMTSetCount.timestamp) ; + smc->mib.fddiSMTLastSetStationId = req->smt_sid ; + smt_add_para(smc,&set_pcon,(u_short) SMT_P1035,0,0) ; + smt_add_para(smc,&set_pcon,(u_short) SMT_P1036,0,0) ; + } + return mb; +} + +static int smt_authorize(struct s_smc *smc, struct smt_header *sm) +{ + struct smt_para *pa ; + int i ; + char *p ; + + /* + * check source station id if not zero + */ + p = (char *) &smc->mib.fddiPRPMFStation ; + for (i = 0 ; i < 8 && !p[i] ; i++) + ; + if (i != 8) { + if (memcmp((char *) &sm->smt_sid, + (char *) &smc->mib.fddiPRPMFStation,8)) + return 1; + } + /* + * check authoriziation parameter if passwd not zero + */ + p = (char *) smc->mib.fddiPRPMFPasswd ; + for (i = 0 ; i < 8 && !p[i] ; i++) + ; + if (i != 8) { + pa = (struct smt_para *) sm_to_para(smc,sm,SMT_P_AUTHOR) ; + if (!pa) + return 1; + if (pa->p_len != 8) + return 1; + if (memcmp((char *)(pa+1),(char *)smc->mib.fddiPRPMFPasswd,8)) + return 1; + } + return 0; +} + +static int smt_check_set_count(struct s_smc *smc, struct smt_header *sm) +{ + struct smt_para *pa ; + struct smt_p_setcount *sc ; + + pa = (struct smt_para *) sm_to_para(smc,sm,SMT_P1035) ; + if (pa) { + sc = (struct smt_p_setcount *) pa ; + if ((smc->mib.fddiSMTSetCount.count != sc->count) || + memcmp((char *) smc->mib.fddiSMTSetCount.timestamp, + (char *)sc->timestamp,8)) + return 1; + } + return 0; +} + +void smt_add_para(struct s_smc *smc, struct s_pcon *pcon, u_short para, + int index, int local) +{ + struct smt_para *pa ; + const struct s_p_tab *pt ; + struct fddi_mib_m *mib_m = NULL; + struct fddi_mib_p *mib_p = NULL; + int len ; + int plen ; + char *from ; + char *to ; + const char *swap ; + char c ; + int range ; + char *mib_addr ; + int mac ; + int path ; + int port ; + int sp_len ; + + /* + * skip if error + */ + if (pcon->pc_err) + return ; + + /* + * actions don't have a value + */ + pt = smt_get_ptab(para) ; + if (pt && pt->p_access == AC_S) + return ; + + to = (char *) (pcon->pc_p) ; /* destination pointer */ + len = pcon->pc_len ; /* free space */ + plen = len ; /* remember start length */ + pa = (struct smt_para *) to ; /* type/length pointer */ + to += PARA_LEN ; /* skip smt_para */ + len -= PARA_LEN ; + /* + * set index if required + */ + if (((range = (para & 0xf000)) == 0x2000) || + range == 0x3000 || range == 0x4000) { + if (len < 4) + goto wrong_error ; + to[0] = 0 ; + to[1] = 0 ; + to[2] = 0 ; + to[3] = index ; + len -= 4 ; + to += 4 ; + } + mac = index - INDEX_MAC ; + path = index - INDEX_PATH ; + port = index - INDEX_PORT ; + /* + * get pointer to mib + */ + switch (range) { + case 0x1000 : + default : + mib_addr = (char *) (&smc->mib) ; + break ; + case 0x2000 : + if (mac < 0 || mac >= NUMMACS) { + pcon->pc_err = SMT_RDF_NOPARAM ; + return ; + } + mib_addr = (char *) (&smc->mib.m[mac]) ; + mib_m = (struct fddi_mib_m *) mib_addr ; + break ; + case 0x3000 : + if (path < 0 || path >= NUMPATHS) { + pcon->pc_err = SMT_RDF_NOPARAM ; + return ; + } + mib_addr = (char *) (&smc->mib.a[path]) ; + break ; + case 0x4000 : + if (port < 0 || port >= smt_mib_phys(smc)) { + pcon->pc_err = SMT_RDF_NOPARAM ; + return ; + } + mib_addr = (char *) (&smc->mib.p[port_to_mib(smc,port)]) ; + mib_p = (struct fddi_mib_p *) mib_addr ; + break ; + } + /* + * check special paras + */ + swap = NULL; + switch (para) { + case SMT_P10F0 : + case SMT_P10F1 : +#ifdef ESS + case SMT_P10F2 : + case SMT_P10F3 : + case SMT_P10F4 : + case SMT_P10F5 : + case SMT_P10F6 : + case SMT_P10F7 : +#endif +#ifdef SBA + case SMT_P10F8 : + case SMT_P10F9 : +#endif + case SMT_P20F1 : + if (!local) { + pcon->pc_err = SMT_RDF_NOPARAM ; + return ; + } + break ; + case SMT_P2034 : + case SMT_P2046 : + case SMT_P2047 : + case SMT_P204A : + case SMT_P2051 : + case SMT_P2052 : + mac_update_counter(smc) ; + break ; + case SMT_P4022: + mib_p->fddiPORTPC_LS = LS2MIB( + sm_pm_get_ls(smc,port_to_mib(smc,port))) ; + break ; + case SMT_P_REASON : + *(u32 *)to = 0 ; + sp_len = 4 ; + goto sp_done ; + case SMT_P1033 : /* time stamp */ + smt_set_timestamp(smc,smc->mib.fddiSMTTimeStamp) ; + break ; + + case SMT_P1020: /* port indexes */ +#if NUMPHYS == 12 + swap = "IIIIIIIIIIII" ; +#else +#if NUMPHYS == 2 + if (smc->s.sas == SMT_SAS) + swap = "I" ; + else + swap = "II" ; +#else +#if NUMPHYS == 24 + swap = "IIIIIIIIIIIIIIIIIIIIIIII" ; +#else + ???? +#endif +#endif +#endif + break ; + case SMT_P3212 : + { + sp_len = cem_build_path(smc,to,path) ; + goto sp_done ; + } + case SMT_P1048 : /* peer wrap condition */ + { + struct smt_p_1048 *sp ; + sp = (struct smt_p_1048 *) to ; + sp->p1048_flag = smc->mib.fddiSMTPeerWrapFlag ; + sp->p1048_cf_state = smc->mib.fddiSMTCF_State ; + sp_len = sizeof(struct smt_p_1048) ; + goto sp_done ; + } + case SMT_P208C : + { + struct smt_p_208c *sp ; + sp = (struct smt_p_208c *) to ; + sp->p208c_flag = + smc->mib.m[MAC0].fddiMACDuplicateAddressCond ; + sp->p208c_dupcondition = + (mib_m->fddiMACDA_Flag ? SMT_ST_MY_DUPA : 0) | + (mib_m->fddiMACUNDA_Flag ? SMT_ST_UNA_DUPA : 0); + sp->p208c_fddilong = + mib_m->fddiMACSMTAddress ; + sp->p208c_fddiunalong = + mib_m->fddiMACUpstreamNbr ; + sp->p208c_pad = 0 ; + sp_len = sizeof(struct smt_p_208c) ; + goto sp_done ; + } + case SMT_P208D : /* frame error condition */ + { + struct smt_p_208d *sp ; + sp = (struct smt_p_208d *) to ; + sp->p208d_flag = + mib_m->fddiMACFrameErrorFlag ; + sp->p208d_frame_ct = + mib_m->fddiMACFrame_Ct ; + sp->p208d_error_ct = + mib_m->fddiMACError_Ct ; + sp->p208d_lost_ct = + mib_m->fddiMACLost_Ct ; + sp->p208d_ratio = + mib_m->fddiMACFrameErrorRatio ; + sp_len = sizeof(struct smt_p_208d) ; + goto sp_done ; + } + case SMT_P208E : /* not copied condition */ + { + struct smt_p_208e *sp ; + sp = (struct smt_p_208e *) to ; + sp->p208e_flag = + mib_m->fddiMACNotCopiedFlag ; + sp->p208e_not_copied = + mib_m->fddiMACNotCopied_Ct ; + sp->p208e_copied = + mib_m->fddiMACCopied_Ct ; + sp->p208e_not_copied_ratio = + mib_m->fddiMACNotCopiedRatio ; + sp_len = sizeof(struct smt_p_208e) ; + goto sp_done ; + } + case SMT_P208F : /* neighbor change event */ + { + struct smt_p_208f *sp ; + sp = (struct smt_p_208f *) to ; + sp->p208f_multiple = + mib_m->fddiMACMultiple_N ; + sp->p208f_nacondition = + mib_m->fddiMACDuplicateAddressCond ; + sp->p208f_old_una = + mib_m->fddiMACOldUpstreamNbr ; + sp->p208f_new_una = + mib_m->fddiMACUpstreamNbr ; + sp->p208f_old_dna = + mib_m->fddiMACOldDownstreamNbr ; + sp->p208f_new_dna = + mib_m->fddiMACDownstreamNbr ; + sp->p208f_curren_path = + mib_m->fddiMACCurrentPath ; + sp->p208f_smt_address = + mib_m->fddiMACSMTAddress ; + sp_len = sizeof(struct smt_p_208f) ; + goto sp_done ; + } + case SMT_P2090 : + { + struct smt_p_2090 *sp ; + sp = (struct smt_p_2090 *) to ; + sp->p2090_multiple = + mib_m->fddiMACMultiple_P ; + sp->p2090_availablepaths = + mib_m->fddiMACAvailablePaths ; + sp->p2090_currentpath = + mib_m->fddiMACCurrentPath ; + sp->p2090_requestedpaths = + mib_m->fddiMACRequestedPaths ; + sp_len = sizeof(struct smt_p_2090) ; + goto sp_done ; + } + case SMT_P4050 : + { + struct smt_p_4050 *sp ; + sp = (struct smt_p_4050 *) to ; + sp->p4050_flag = + mib_p->fddiPORTLerFlag ; + sp->p4050_pad = 0 ; + sp->p4050_cutoff = + mib_p->fddiPORTLer_Cutoff ; + sp->p4050_alarm = + mib_p->fddiPORTLer_Alarm ; + sp->p4050_estimate = + mib_p->fddiPORTLer_Estimate ; + sp->p4050_reject_ct = + mib_p->fddiPORTLem_Reject_Ct ; + sp->p4050_ct = + mib_p->fddiPORTLem_Ct ; + sp_len = sizeof(struct smt_p_4050) ; + goto sp_done ; + } + + case SMT_P4051 : + { + struct smt_p_4051 *sp ; + sp = (struct smt_p_4051 *) to ; + sp->p4051_multiple = + mib_p->fddiPORTMultiple_U ; + sp->p4051_porttype = + mib_p->fddiPORTMy_Type ; + sp->p4051_connectstate = + mib_p->fddiPORTConnectState ; + sp->p4051_pc_neighbor = + mib_p->fddiPORTNeighborType ; + sp->p4051_pc_withhold = + mib_p->fddiPORTPC_Withhold ; + sp_len = sizeof(struct smt_p_4051) ; + goto sp_done ; + } + case SMT_P4052 : + { + struct smt_p_4052 *sp ; + sp = (struct smt_p_4052 *) to ; + sp->p4052_flag = + mib_p->fddiPORTEB_Condition ; + sp->p4052_eberrorcount = + mib_p->fddiPORTEBError_Ct ; + sp_len = sizeof(struct smt_p_4052) ; + goto sp_done ; + } + case SMT_P4053 : + { + struct smt_p_4053 *sp ; + sp = (struct smt_p_4053 *) to ; + sp->p4053_multiple = + mib_p->fddiPORTMultiple_P ; + sp->p4053_availablepaths = + mib_p->fddiPORTAvailablePaths ; + sp->p4053_currentpath = + mib_p->fddiPORTCurrentPath ; + memcpy( (char *) &sp->p4053_requestedpaths, + (char *) mib_p->fddiPORTRequestedPaths,4) ; + sp->p4053_mytype = + mib_p->fddiPORTMy_Type ; + sp->p4053_neighbortype = + mib_p->fddiPORTNeighborType ; + sp_len = sizeof(struct smt_p_4053) ; + goto sp_done ; + } + default : + break ; + } + /* + * in table ? + */ + if (!pt) { + pcon->pc_err = (para & 0xff00) ? SMT_RDF_NOPARAM : + SMT_RDF_ILLEGAL ; + return ; + } + /* + * check access rights + */ + switch (pt->p_access) { + case AC_G : + case AC_GR : + break ; + default : + pcon->pc_err = SMT_RDF_ILLEGAL ; + return ; + } + from = mib_addr + pt->p_offset ; + if (!swap) + swap = pt->p_swap ; /* pointer to swap string */ + + /* + * copy values + */ + while ((c = *swap++)) { + switch(c) { + case 'b' : + case 'w' : + case 'l' : + break ; + case 'S' : + case 'E' : + case 'R' : + case 'r' : + if (len < 4) + goto len_error ; + to[0] = 0 ; + to[1] = 0 ; +#ifdef LITTLE_ENDIAN + if (c == 'r') { + to[2] = *from++ ; + to[3] = *from++ ; + } + else { + to[3] = *from++ ; + to[2] = *from++ ; + } +#else + to[2] = *from++ ; + to[3] = *from++ ; +#endif + to += 4 ; + len -= 4 ; + break ; + case 'I' : /* for SET of port indexes */ + if (len < 2) + goto len_error ; +#ifdef LITTLE_ENDIAN + to[1] = *from++ ; + to[0] = *from++ ; +#else + to[0] = *from++ ; + to[1] = *from++ ; +#endif + to += 2 ; + len -= 2 ; + break ; + case 'F' : + case 'B' : + if (len < 4) + goto len_error ; + len -= 4 ; + to[0] = 0 ; + to[1] = 0 ; + to[2] = 0 ; + to[3] = *from++ ; + to += 4 ; + break ; + case 'C' : + case 'T' : + case 'L' : + if (len < 4) + goto len_error ; +#ifdef LITTLE_ENDIAN + to[3] = *from++ ; + to[2] = *from++ ; + to[1] = *from++ ; + to[0] = *from++ ; +#else + to[0] = *from++ ; + to[1] = *from++ ; + to[2] = *from++ ; + to[3] = *from++ ; +#endif + len -= 4 ; + to += 4 ; + break ; + case '2' : /* PortMacIndicated */ + if (len < 4) + goto len_error ; + to[0] = 0 ; + to[1] = 0 ; + to[2] = *from++ ; + to[3] = *from++ ; + len -= 4 ; + to += 4 ; + break ; + case '4' : + if (len < 4) + goto len_error ; + to[0] = *from++ ; + to[1] = *from++ ; + to[2] = *from++ ; + to[3] = *from++ ; + len -= 4 ; + to += 4 ; + break ; + case 'A' : + if (len < 8) + goto len_error ; + to[0] = 0 ; + to[1] = 0 ; + memcpy((char *) to+2,(char *) from,6) ; + to += 8 ; + from += 8 ; + len -= 8 ; + break ; + case '8' : + if (len < 8) + goto len_error ; + memcpy((char *) to,(char *) from,8) ; + to += 8 ; + from += 8 ; + len -= 8 ; + break ; + case 'D' : + if (len < 32) + goto len_error ; + memcpy((char *) to,(char *) from,32) ; + to += 32 ; + from += 32 ; + len -= 32 ; + break ; + case 'P' : /* timestamp is NOT swapped */ + if (len < 8) + goto len_error ; + to[0] = *from++ ; + to[1] = *from++ ; + to[2] = *from++ ; + to[3] = *from++ ; + to[4] = *from++ ; + to[5] = *from++ ; + to[6] = *from++ ; + to[7] = *from++ ; + to += 8 ; + len -= 8 ; + break ; + default : + SMT_PANIC(smc,SMT_E0119, SMT_E0119_MSG) ; + break ; + } + } + +done: + /* + * make it even (in case of 'I' encoding) + * note: len is DECREMENTED + */ + if (len & 3) { + to[0] = 0 ; + to[1] = 0 ; + to += 4 - (len & 3 ) ; + len = len & ~ 3 ; + } + + /* set type and length */ + pa->p_type = para ; + pa->p_len = plen - len - PARA_LEN ; + /* return values */ + pcon->pc_p = (void *) to ; + pcon->pc_len = len ; + return ; + +sp_done: + len -= sp_len ; + to += sp_len ; + goto done ; + +len_error: + /* parameter does not fit in frame */ + pcon->pc_err = SMT_RDF_TOOLONG ; + return ; + +wrong_error: + pcon->pc_err = SMT_RDF_LENGTH ; +} + +/* + * set parameter + */ +static int smt_set_para(struct s_smc *smc, struct smt_para *pa, int index, + int local, int set) +{ +#define IFSET(x) if (set) (x) + + const struct s_p_tab *pt ; + int len ; + char *from ; + char *to ; + const char *swap ; + char c ; + char *mib_addr ; + struct fddi_mib *mib ; + struct fddi_mib_m *mib_m = NULL; + struct fddi_mib_a *mib_a = NULL; + struct fddi_mib_p *mib_p = NULL; + int mac ; + int path ; + int port ; + SK_LOC_DECL(u_char,byte_val) ; + SK_LOC_DECL(u_short,word_val) ; + SK_LOC_DECL(u_long,long_val) ; + + mac = index - INDEX_MAC ; + path = index - INDEX_PATH ; + port = index - INDEX_PORT ; + len = pa->p_len ; + from = (char *) (pa + 1 ) ; + + mib = &smc->mib ; + switch (pa->p_type & 0xf000) { + case 0x1000 : + default : + mib_addr = (char *) mib ; + break ; + case 0x2000 : + if (mac < 0 || mac >= NUMMACS) { + return SMT_RDF_NOPARAM; + } + mib_m = &smc->mib.m[mac] ; + mib_addr = (char *) mib_m ; + from += 4 ; /* skip index */ + len -= 4 ; + break ; + case 0x3000 : + if (path < 0 || path >= NUMPATHS) { + return SMT_RDF_NOPARAM; + } + mib_a = &smc->mib.a[path] ; + mib_addr = (char *) mib_a ; + from += 4 ; /* skip index */ + len -= 4 ; + break ; + case 0x4000 : + if (port < 0 || port >= smt_mib_phys(smc)) { + return SMT_RDF_NOPARAM; + } + mib_p = &smc->mib.p[port_to_mib(smc,port)] ; + mib_addr = (char *) mib_p ; + from += 4 ; /* skip index */ + len -= 4 ; + break ; + } + switch (pa->p_type) { + case SMT_P10F0 : + case SMT_P10F1 : +#ifdef ESS + case SMT_P10F2 : + case SMT_P10F3 : + case SMT_P10F4 : + case SMT_P10F5 : + case SMT_P10F6 : + case SMT_P10F7 : +#endif +#ifdef SBA + case SMT_P10F8 : + case SMT_P10F9 : +#endif + case SMT_P20F1 : + if (!local) + return SMT_RDF_NOPARAM; + break ; + } + pt = smt_get_ptab(pa->p_type) ; + if (!pt) + return (pa->p_type & 0xff00) ? SMT_RDF_NOPARAM : + SMT_RDF_ILLEGAL; + switch (pt->p_access) { + case AC_GR : + case AC_S : + break ; + default : + return SMT_RDF_ILLEGAL; + } + to = mib_addr + pt->p_offset ; + swap = pt->p_swap ; /* pointer to swap string */ + + while (swap && (c = *swap++)) { + switch(c) { + case 'b' : + to = (char *) &byte_val ; + break ; + case 'w' : + to = (char *) &word_val ; + break ; + case 'l' : + to = (char *) &long_val ; + break ; + case 'S' : + case 'E' : + case 'R' : + case 'r' : + if (len < 4) { + goto len_error ; + } + if (from[0] | from[1]) + goto val_error ; +#ifdef LITTLE_ENDIAN + if (c == 'r') { + to[0] = from[2] ; + to[1] = from[3] ; + } + else { + to[1] = from[2] ; + to[0] = from[3] ; + } +#else + to[0] = from[2] ; + to[1] = from[3] ; +#endif + from += 4 ; + to += 2 ; + len -= 4 ; + break ; + case 'F' : + case 'B' : + if (len < 4) { + goto len_error ; + } + if (from[0] | from[1] | from[2]) + goto val_error ; + to[0] = from[3] ; + len -= 4 ; + from += 4 ; + to += 4 ; + break ; + case 'C' : + case 'T' : + case 'L' : + if (len < 4) { + goto len_error ; + } +#ifdef LITTLE_ENDIAN + to[3] = *from++ ; + to[2] = *from++ ; + to[1] = *from++ ; + to[0] = *from++ ; +#else + to[0] = *from++ ; + to[1] = *from++ ; + to[2] = *from++ ; + to[3] = *from++ ; +#endif + len -= 4 ; + to += 4 ; + break ; + case 'A' : + if (len < 8) + goto len_error ; + if (set) + memcpy(to,from+2,6) ; + to += 8 ; + from += 8 ; + len -= 8 ; + break ; + case '4' : + if (len < 4) + goto len_error ; + if (set) + memcpy(to,from,4) ; + to += 4 ; + from += 4 ; + len -= 4 ; + break ; + case '8' : + if (len < 8) + goto len_error ; + if (set) + memcpy(to,from,8) ; + to += 8 ; + from += 8 ; + len -= 8 ; + break ; + case 'D' : + if (len < 32) + goto len_error ; + if (set) + memcpy(to,from,32) ; + to += 32 ; + from += 32 ; + len -= 32 ; + break ; + case 'P' : /* timestamp is NOT swapped */ + if (set) { + to[0] = *from++ ; + to[1] = *from++ ; + to[2] = *from++ ; + to[3] = *from++ ; + to[4] = *from++ ; + to[5] = *from++ ; + to[6] = *from++ ; + to[7] = *from++ ; + } + to += 8 ; + len -= 8 ; + break ; + default : + SMT_PANIC(smc,SMT_E0120, SMT_E0120_MSG) ; + return SMT_RDF_ILLEGAL; + } + } + /* + * actions and internal updates + */ + switch (pa->p_type) { + case SMT_P101A: /* fddiSMTConfigPolicy */ + if (word_val & ~1) + goto val_error ; + IFSET(mib->fddiSMTConfigPolicy = word_val) ; + break ; + case SMT_P101B : /* fddiSMTConnectionPolicy */ + if (!(word_val & POLICY_MM)) + goto val_error ; + IFSET(mib->fddiSMTConnectionPolicy = word_val) ; + break ; + case SMT_P101D : /* fddiSMTTT_Notify */ + if (word_val < 2 || word_val > 30) + goto val_error ; + IFSET(mib->fddiSMTTT_Notify = word_val) ; + break ; + case SMT_P101E : /* fddiSMTStatRptPolicy */ + if (byte_val & ~1) + goto val_error ; + IFSET(mib->fddiSMTStatRptPolicy = byte_val) ; + break ; + case SMT_P101F : /* fddiSMTTrace_MaxExpiration */ + /* + * note: lower limit trace_max = 6.001773... s + * NO upper limit + */ + if (long_val < (long)0x478bf51L) + goto val_error ; + IFSET(mib->fddiSMTTrace_MaxExpiration = long_val) ; + break ; +#ifdef ESS + case SMT_P10F2 : /* fddiESSPayload */ + if (long_val > 1562) + goto val_error ; + if (set && smc->mib.fddiESSPayload != long_val) { + smc->ess.raf_act_timer_poll = TRUE ; + smc->mib.fddiESSPayload = long_val ; + } + break ; + case SMT_P10F3 : /* fddiESSOverhead */ + if (long_val < 50 || long_val > 5000) + goto val_error ; + if (set && smc->mib.fddiESSPayload && + smc->mib.fddiESSOverhead != long_val) { + smc->ess.raf_act_timer_poll = TRUE ; + smc->mib.fddiESSOverhead = long_val ; + } + break ; + case SMT_P10F4 : /* fddiESSMaxTNeg */ + if (long_val > -MS2BCLK(5) || long_val < -MS2BCLK(165)) + goto val_error ; + IFSET(mib->fddiESSMaxTNeg = long_val) ; + break ; + case SMT_P10F5 : /* fddiESSMinSegmentSize */ + if (long_val < 1 || long_val > 4478) + goto val_error ; + IFSET(mib->fddiESSMinSegmentSize = long_val) ; + break ; + case SMT_P10F6 : /* fddiESSCategory */ + if ((long_val & 0xffff) != 1) + goto val_error ; + IFSET(mib->fddiESSCategory = long_val) ; + break ; + case SMT_P10F7 : /* fddiESSSyncTxMode */ + if (word_val > 1) + goto val_error ; + IFSET(mib->fddiESSSynchTxMode = word_val) ; + break ; +#endif +#ifdef SBA + case SMT_P10F8 : /* fddiSBACommand */ + if (byte_val != SB_STOP && byte_val != SB_START) + goto val_error ; + IFSET(mib->fddiSBACommand = byte_val) ; + break ; + case SMT_P10F9 : /* fddiSBAAvailable */ + if (byte_val > 100) + goto val_error ; + IFSET(mib->fddiSBAAvailable = byte_val) ; + break ; +#endif + case SMT_P2020 : /* fddiMACRequestedPaths */ + if ((word_val & (MIB_P_PATH_PRIM_PREFER | + MIB_P_PATH_PRIM_ALTER)) == 0 ) + goto val_error ; + IFSET(mib_m->fddiMACRequestedPaths = word_val) ; + break ; + case SMT_P205F : /* fddiMACFrameErrorThreshold */ + /* 0 .. ffff acceptable */ + IFSET(mib_m->fddiMACFrameErrorThreshold = word_val) ; + break ; + case SMT_P2067 : /* fddiMACNotCopiedThreshold */ + /* 0 .. ffff acceptable */ + IFSET(mib_m->fddiMACNotCopiedThreshold = word_val) ; + break ; + case SMT_P2076: /* fddiMACMA_UnitdataEnable */ + if (byte_val & ~1) + goto val_error ; + if (set) { + mib_m->fddiMACMA_UnitdataEnable = byte_val ; + queue_event(smc,EVENT_RMT,RM_ENABLE_FLAG) ; + } + break ; + case SMT_P20F1 : /* fddiMACT_Min */ + IFSET(mib_m->fddiMACT_Min = long_val) ; + break ; + case SMT_P320F : + if (long_val > 1562) + goto val_error ; + IFSET(mib_a->fddiPATHSbaPayload = long_val) ; +#ifdef ESS + if (set) + ess_para_change(smc) ; +#endif + break ; + case SMT_P3210 : + if (long_val > 5000) + goto val_error ; + + if (long_val != 0 && mib_a->fddiPATHSbaPayload == 0) + goto val_error ; + + IFSET(mib_a->fddiPATHSbaOverhead = long_val) ; +#ifdef ESS + if (set) + ess_para_change(smc) ; +#endif + break ; + case SMT_P3213: /* fddiPATHT_Rmode */ + /* no limit : + * 0 .. 343.597 => 0 .. 2e32 * 80nS + */ + if (set) { + mib_a->fddiPATHT_Rmode = long_val ; + rtm_set_timer(smc) ; + } + break ; + case SMT_P3214 : /* fddiPATHSbaAvailable */ + if (long_val > 0x00BEBC20L) + goto val_error ; +#ifdef SBA + if (set && mib->fddiSBACommand == SB_STOP) + goto val_error ; +#endif + IFSET(mib_a->fddiPATHSbaAvailable = long_val) ; + break ; + case SMT_P3215 : /* fddiPATHTVXLowerBound */ + IFSET(mib_a->fddiPATHTVXLowerBound = long_val) ; + goto change_mac_para ; + case SMT_P3216 : /* fddiPATHT_MaxLowerBound */ + IFSET(mib_a->fddiPATHT_MaxLowerBound = long_val) ; + goto change_mac_para ; + case SMT_P3217 : /* fddiPATHMaxT_Req */ + IFSET(mib_a->fddiPATHMaxT_Req = long_val) ; + +change_mac_para: + if (set && smt_set_mac_opvalues(smc)) { + RS_SET(smc,RS_EVENT) ; + smc->sm.please_reconnect = 1 ; + queue_event(smc,EVENT_ECM,EC_DISCONNECT) ; + } + break ; + case SMT_P400E : /* fddiPORTConnectionPolicies */ + if (byte_val > 1) + goto val_error ; + IFSET(mib_p->fddiPORTConnectionPolicies = byte_val) ; + break ; + case SMT_P4011 : /* fddiPORTRequestedPaths */ + /* all 3*8 bits allowed */ + IFSET(memcpy((char *)mib_p->fddiPORTRequestedPaths, + (char *)&long_val,4)) ; + break ; + case SMT_P401F: /* fddiPORTMaint_LS */ + if (word_val > 4) + goto val_error ; + IFSET(mib_p->fddiPORTMaint_LS = word_val) ; + break ; + case SMT_P403A : /* fddiPORTLer_Cutoff */ + if (byte_val < 4 || byte_val > 15) + goto val_error ; + IFSET(mib_p->fddiPORTLer_Cutoff = byte_val) ; + break ; + case SMT_P403B : /* fddiPORTLer_Alarm */ + if (byte_val < 4 || byte_val > 15) + goto val_error ; + IFSET(mib_p->fddiPORTLer_Alarm = byte_val) ; + break ; + + /* + * Actions + */ + case SMT_P103C : /* fddiSMTStationAction */ + if (smt_action(smc,SMT_STATION_ACTION, (int) word_val, 0)) + goto val_error ; + break ; + case SMT_P4046: /* fddiPORTAction */ + if (smt_action(smc,SMT_PORT_ACTION, (int) word_val, + port_to_mib(smc,port))) + goto val_error ; + break ; + default : + break ; + } + return 0; + +val_error: + /* parameter value in frame is out of range */ + return SMT_RDF_RANGE; + +len_error: + /* parameter value in frame is too short */ + return SMT_RDF_LENGTH; + +#if 0 +no_author_error: + /* parameter not setable, because the SBA is not active + * Please note: we give the return code 'not authorizeed + * because SBA denied is not a valid return code in the + * PMF protocol. + */ + return SMT_RDF_AUTHOR; +#endif +} + +static const struct s_p_tab *smt_get_ptab(u_short para) +{ + const struct s_p_tab *pt ; + for (pt = p_tab ; pt->p_num && pt->p_num != para ; pt++) + ; + return pt->p_num ? pt : NULL; +} + +static int smt_mib_phys(struct s_smc *smc) +{ +#ifdef CONCENTRATOR + SK_UNUSED(smc) ; + + return NUMPHYS; +#else + if (smc->s.sas == SMT_SAS) + return 1; + return NUMPHYS; +#endif +} + +static int port_to_mib(struct s_smc *smc, int p) +{ +#ifdef CONCENTRATOR + SK_UNUSED(smc) ; + + return p; +#else + if (smc->s.sas == SMT_SAS) + return PS; + return p; +#endif +} + + +#ifdef DEBUG +#ifndef BOOT +void dump_smt(struct s_smc *smc, struct smt_header *sm, char *text) +{ + int len ; + struct smt_para *pa ; + char *c ; + int n ; + int nn ; +#ifdef LITTLE_ENDIAN + int smtlen ; +#endif + + SK_UNUSED(smc) ; + +#ifdef DEBUG_BRD + if (smc->debug.d_smtf < 2) +#else + if (debug.d_smtf < 2) +#endif + return ; +#ifdef LITTLE_ENDIAN + smtlen = sm->smt_len + sizeof(struct smt_header) ; +#endif + printf("SMT Frame [%s]:\nDA ",text) ; + dump_hex((char *) &sm->smt_dest,6) ; + printf("\tSA ") ; + dump_hex((char *) &sm->smt_source,6) ; + printf(" Class %x Type %x Version %x\n", + sm->smt_class,sm->smt_type,sm->smt_version) ; + printf("TID %lx\t\tSID ",sm->smt_tid) ; + dump_hex((char *) &sm->smt_sid,8) ; + printf(" LEN %x\n",sm->smt_len) ; + + len = sm->smt_len ; + pa = (struct smt_para *) (sm + 1) ; + while (len > 0 ) { + int plen ; +#ifdef UNIX + printf("TYPE %x LEN %x VALUE\t",pa->p_type,pa->p_len) ; +#else + printf("TYPE %04x LEN %2x VALUE\t",pa->p_type,pa->p_len) ; +#endif + n = pa->p_len ; + if ( (n < 0 ) || (n > (int)(len - PARA_LEN))) { + n = len - PARA_LEN ; + printf(" BAD LENGTH\n") ; + break ; + } +#ifdef LITTLE_ENDIAN + smt_swap_para(sm,smtlen,0) ; +#endif + if (n < 24) { + dump_hex((char *)(pa+1),(int) n) ; + printf("\n") ; + } + else { + int first = 0 ; + c = (char *)(pa+1) ; + dump_hex(c,16) ; + printf("\n") ; + n -= 16 ; + c += 16 ; + while (n > 0) { + nn = (n > 16) ? 16 : n ; + if (n > 64) { + if (first == 0) + printf("\t\t\t...\n") ; + first = 1 ; + } + else { + printf("\t\t\t") ; + dump_hex(c,nn) ; + printf("\n") ; + } + n -= nn ; + c += 16 ; + } + } +#ifdef LITTLE_ENDIAN + smt_swap_para(sm,smtlen,1) ; +#endif + plen = (pa->p_len + PARA_LEN + 3) & ~3 ; + len -= plen ; + pa = (struct smt_para *)((char *)pa + plen) ; + } + printf("-------------------------------------------------\n\n") ; +} + +void dump_hex(char *p, int len) +{ + int n = 0 ; + while (len--) { + n++ ; +#ifdef UNIX + printf("%x%s",*p++ & 0xff,len ? ( (n & 7) ? " " : "-") : "") ; +#else + printf("%02x%s",*p++ & 0xff,len ? ( (n & 7) ? " " : "-") : "") ; +#endif + } +} +#endif /* no BOOT */ +#endif /* DEBUG */ + + +#endif /* no SLIM_SMT */ diff --git a/kernel/drivers/net/fddi/skfp/queue.c b/kernel/drivers/net/fddi/skfp/queue.c new file mode 100644 index 000000000..c1a0df455 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/queue.c @@ -0,0 +1,173 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + SMT Event Queue Management +*/ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)queue.c 2.9 97/08/04 (C) SK " ; +#endif + +#define PRINTF(a,b,c) + +/* + * init event queue management + */ +void ev_init(struct s_smc *smc) +{ + smc->q.ev_put = smc->q.ev_get = smc->q.ev_queue ; +} + +/* + * add event to queue + */ +void queue_event(struct s_smc *smc, int class, int event) +{ + PRINTF("queue class %d event %d\n",class,event) ; + smc->q.ev_put->class = class ; + smc->q.ev_put->event = event ; + if (++smc->q.ev_put == &smc->q.ev_queue[MAX_EVENT]) + smc->q.ev_put = smc->q.ev_queue ; + + if (smc->q.ev_put == smc->q.ev_get) { + SMT_ERR_LOG(smc,SMT_E0137, SMT_E0137_MSG) ; + } +} + +/* + * timer_event is called from HW timer package. + */ +void timer_event(struct s_smc *smc, u_long token) +{ + PRINTF("timer event class %d token %d\n", + EV_T_CLASS(token), + EV_T_EVENT(token)) ; + queue_event(smc,EV_T_CLASS(token),EV_T_EVENT(token)); +} + +/* + * event dispatcher + * while event queue is not empty + * get event from queue + * send command to state machine + * end + */ +void ev_dispatcher(struct s_smc *smc) +{ + struct event_queue *ev ; /* pointer into queue */ + int class ; + + ev = smc->q.ev_get ; + PRINTF("dispatch get %x put %x\n",ev,smc->q.ev_put) ; + while (ev != smc->q.ev_put) { + PRINTF("dispatch class %d event %d\n",ev->class,ev->event) ; + switch(class = ev->class) { + case EVENT_ECM : /* Entity Corordination Man. */ + ecm(smc,(int)ev->event) ; + break ; + case EVENT_CFM : /* Configuration Man. */ + cfm(smc,(int)ev->event) ; + break ; + case EVENT_RMT : /* Ring Man. */ + rmt(smc,(int)ev->event) ; + break ; + case EVENT_SMT : + smt_event(smc,(int)ev->event) ; + break ; +#ifdef CONCENTRATOR + case 99 : + timer_test_event(smc,(int)ev->event) ; + break ; +#endif + case EVENT_PCMA : /* PHY A */ + case EVENT_PCMB : /* PHY B */ + default : + if (class >= EVENT_PCMA && + class < EVENT_PCMA + NUMPHYS) { + pcm(smc,class - EVENT_PCMA,(int)ev->event) ; + break ; + } + SMT_PANIC(smc,SMT_E0121, SMT_E0121_MSG) ; + return ; + } + + if (++ev == &smc->q.ev_queue[MAX_EVENT]) + ev = smc->q.ev_queue ; + + /* Renew get: it is used in queue_events to detect overruns */ + smc->q.ev_get = ev; + } +} + +/* + * smt_online connects to or disconnects from the ring + * MUST be called to initiate connection establishment + * + * on 0 disconnect + * on 1 connect + */ +u_short smt_online(struct s_smc *smc, int on) +{ + queue_event(smc,EVENT_ECM,on ? EC_CONNECT : EC_DISCONNECT) ; + ev_dispatcher(smc) ; + return smc->mib.fddiSMTCF_State; +} + +/* + * set SMT flag to value + * flag flag name + * value flag value + * dump current flag setting + */ +#ifdef CONCENTRATOR +void do_smt_flag(struct s_smc *smc, char *flag, int value) +{ +#ifdef DEBUG + struct smt_debug *deb; + + SK_UNUSED(smc) ; + +#ifdef DEBUG_BRD + deb = &smc->debug; +#else + deb = &debug; +#endif + if (!strcmp(flag,"smt")) + deb->d_smt = value ; + else if (!strcmp(flag,"smtf")) + deb->d_smtf = value ; + else if (!strcmp(flag,"pcm")) + deb->d_pcm = value ; + else if (!strcmp(flag,"rmt")) + deb->d_rmt = value ; + else if (!strcmp(flag,"cfm")) + deb->d_cfm = value ; + else if (!strcmp(flag,"ecm")) + deb->d_ecm = value ; + printf("smt %d\n",deb->d_smt) ; + printf("smtf %d\n",deb->d_smtf) ; + printf("pcm %d\n",deb->d_pcm) ; + printf("rmt %d\n",deb->d_rmt) ; + printf("cfm %d\n",deb->d_cfm) ; + printf("ecm %d\n",deb->d_ecm) ; +#endif /* DEBUG */ +} +#endif diff --git a/kernel/drivers/net/fddi/skfp/rmt.c b/kernel/drivers/net/fddi/skfp/rmt.c new file mode 100644 index 000000000..ef8d5672d --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/rmt.c @@ -0,0 +1,654 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + SMT RMT + Ring Management +*/ + +/* + * Hardware independent state machine implemantation + * The following external SMT functions are referenced : + * + * queue_event() + * smt_timer_start() + * smt_timer_stop() + * + * The following external HW dependent functions are referenced : + * sm_ma_control() + * sm_mac_check_beacon_claim() + * + * The following HW dependent events are required : + * RM_RING_OP + * RM_RING_NON_OP + * RM_MY_BEACON + * RM_OTHER_BEACON + * RM_MY_CLAIM + * RM_TRT_EXP + * RM_VALID_CLAIM + * + */ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" + +#define KERNEL +#include "h/smtstate.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)rmt.c 2.13 99/07/02 (C) SK " ; +#endif + +/* + * FSM Macros + */ +#define AFLAG 0x10 +#define GO_STATE(x) (smc->mib.m[MAC0].fddiMACRMTState = (x)|AFLAG) +#define ACTIONS_DONE() (smc->mib.m[MAC0].fddiMACRMTState &= ~AFLAG) +#define ACTIONS(x) (x|AFLAG) + +#define RM0_ISOLATED 0 +#define RM1_NON_OP 1 /* not operational */ +#define RM2_RING_OP 2 /* ring operational */ +#define RM3_DETECT 3 /* detect dupl addresses */ +#define RM4_NON_OP_DUP 4 /* dupl. addr detected */ +#define RM5_RING_OP_DUP 5 /* ring oper. with dupl. addr */ +#define RM6_DIRECTED 6 /* sending directed beacons */ +#define RM7_TRACE 7 /* trace initiated */ + +#ifdef DEBUG +/* + * symbolic state names + */ +static const char * const rmt_states[] = { + "RM0_ISOLATED","RM1_NON_OP","RM2_RING_OP","RM3_DETECT", + "RM4_NON_OP_DUP","RM5_RING_OP_DUP","RM6_DIRECTED", + "RM7_TRACE" +} ; + +/* + * symbolic event names + */ +static const char * const rmt_events[] = { + "NONE","RM_RING_OP","RM_RING_NON_OP","RM_MY_BEACON", + "RM_OTHER_BEACON","RM_MY_CLAIM","RM_TRT_EXP","RM_VALID_CLAIM", + "RM_JOIN","RM_LOOP","RM_DUP_ADDR","RM_ENABLE_FLAG", + "RM_TIMEOUT_NON_OP","RM_TIMEOUT_T_STUCK", + "RM_TIMEOUT_ANNOUNCE","RM_TIMEOUT_T_DIRECT", + "RM_TIMEOUT_D_MAX","RM_TIMEOUT_POLL","RM_TX_STATE_CHANGE" +} ; +#endif + +/* + * Globals + * in struct s_rmt + */ + + +/* + * function declarations + */ +static void rmt_fsm(struct s_smc *smc, int cmd); +static void start_rmt_timer0(struct s_smc *smc, u_long value, int event); +static void start_rmt_timer1(struct s_smc *smc, u_long value, int event); +static void start_rmt_timer2(struct s_smc *smc, u_long value, int event); +static void stop_rmt_timer0(struct s_smc *smc); +static void stop_rmt_timer1(struct s_smc *smc); +static void stop_rmt_timer2(struct s_smc *smc); +static void rmt_dup_actions(struct s_smc *smc); +static void rmt_reinsert_actions(struct s_smc *smc); +static void rmt_leave_actions(struct s_smc *smc); +static void rmt_new_dup_actions(struct s_smc *smc); + +#ifndef SUPERNET_3 +extern void restart_trt_for_dbcn() ; +#endif /*SUPERNET_3*/ + +/* + init RMT state machine + clear all RMT vars and flags +*/ +void rmt_init(struct s_smc *smc) +{ + smc->mib.m[MAC0].fddiMACRMTState = ACTIONS(RM0_ISOLATED) ; + smc->r.dup_addr_test = DA_NONE ; + smc->r.da_flag = 0 ; + smc->mib.m[MAC0].fddiMACMA_UnitdataAvailable = FALSE ; + smc->r.sm_ma_avail = FALSE ; + smc->r.loop_avail = 0 ; + smc->r.bn_flag = 0 ; + smc->r.jm_flag = 0 ; + smc->r.no_flag = TRUE ; +} + +/* + RMT state machine + called by dispatcher + + do + display state change + process event + until SM is stable +*/ +void rmt(struct s_smc *smc, int event) +{ + int state ; + + do { + DB_RMT("RMT : state %s%s", + (smc->mib.m[MAC0].fddiMACRMTState & AFLAG) ? "ACTIONS " : "", + rmt_states[smc->mib.m[MAC0].fddiMACRMTState & ~AFLAG]) ; + DB_RMT(" event %s\n",rmt_events[event],0) ; + state = smc->mib.m[MAC0].fddiMACRMTState ; + rmt_fsm(smc,event) ; + event = 0 ; + } while (state != smc->mib.m[MAC0].fddiMACRMTState) ; + rmt_state_change(smc,(int)smc->mib.m[MAC0].fddiMACRMTState) ; +} + +/* + process RMT event +*/ +static void rmt_fsm(struct s_smc *smc, int cmd) +{ + /* + * RM00-RM70 : from all states + */ + if (!smc->r.rm_join && !smc->r.rm_loop && + smc->mib.m[MAC0].fddiMACRMTState != ACTIONS(RM0_ISOLATED) && + smc->mib.m[MAC0].fddiMACRMTState != RM0_ISOLATED) { + RS_SET(smc,RS_NORINGOP) ; + rmt_indication(smc,0) ; + GO_STATE(RM0_ISOLATED) ; + return ; + } + + switch(smc->mib.m[MAC0].fddiMACRMTState) { + case ACTIONS(RM0_ISOLATED) : + stop_rmt_timer0(smc) ; + stop_rmt_timer1(smc) ; + stop_rmt_timer2(smc) ; + + /* + * Disable MAC. + */ + sm_ma_control(smc,MA_OFFLINE) ; + smc->mib.m[MAC0].fddiMACMA_UnitdataAvailable = FALSE ; + smc->r.loop_avail = FALSE ; + smc->r.sm_ma_avail = FALSE ; + smc->r.no_flag = TRUE ; + DB_RMTN(1,"RMT : ISOLATED\n",0,0) ; + ACTIONS_DONE() ; + break ; + case RM0_ISOLATED : + /*RM01*/ + if (smc->r.rm_join || smc->r.rm_loop) { + /* + * According to the standard the MAC must be reset + * here. The FORMAC will be initialized and Claim + * and Beacon Frames will be uploaded to the MAC. + * So any change of Treq will take effect NOW. + */ + sm_ma_control(smc,MA_RESET) ; + GO_STATE(RM1_NON_OP) ; + break ; + } + break ; + case ACTIONS(RM1_NON_OP) : + start_rmt_timer0(smc,smc->s.rmt_t_non_op,RM_TIMEOUT_NON_OP) ; + stop_rmt_timer1(smc) ; + stop_rmt_timer2(smc) ; + sm_ma_control(smc,MA_BEACON) ; + DB_RMTN(1,"RMT : RING DOWN\n",0,0) ; + RS_SET(smc,RS_NORINGOP) ; + smc->r.sm_ma_avail = FALSE ; + rmt_indication(smc,0) ; + ACTIONS_DONE() ; + break ; + case RM1_NON_OP : + /*RM12*/ + if (cmd == RM_RING_OP) { + RS_SET(smc,RS_RINGOPCHANGE) ; + GO_STATE(RM2_RING_OP) ; + break ; + } + /*RM13*/ + else if (cmd == RM_TIMEOUT_NON_OP) { + smc->r.bn_flag = FALSE ; + smc->r.no_flag = TRUE ; + GO_STATE(RM3_DETECT) ; + break ; + } + break ; + case ACTIONS(RM2_RING_OP) : + stop_rmt_timer0(smc) ; + stop_rmt_timer1(smc) ; + stop_rmt_timer2(smc) ; + smc->r.no_flag = FALSE ; + if (smc->r.rm_loop) + smc->r.loop_avail = TRUE ; + if (smc->r.rm_join) { + smc->r.sm_ma_avail = TRUE ; + if (smc->mib.m[MAC0].fddiMACMA_UnitdataEnable) + smc->mib.m[MAC0].fddiMACMA_UnitdataAvailable = TRUE ; + else + smc->mib.m[MAC0].fddiMACMA_UnitdataAvailable = FALSE ; + } + DB_RMTN(1,"RMT : RING UP\n",0,0) ; + RS_CLEAR(smc,RS_NORINGOP) ; + RS_SET(smc,RS_RINGOPCHANGE) ; + rmt_indication(smc,1) ; + smt_stat_counter(smc,0) ; + ACTIONS_DONE() ; + break ; + case RM2_RING_OP : + /*RM21*/ + if (cmd == RM_RING_NON_OP) { + smc->mib.m[MAC0].fddiMACMA_UnitdataAvailable = FALSE ; + smc->r.loop_avail = FALSE ; + RS_SET(smc,RS_RINGOPCHANGE) ; + GO_STATE(RM1_NON_OP) ; + break ; + } + /*RM22a*/ + else if (cmd == RM_ENABLE_FLAG) { + if (smc->mib.m[MAC0].fddiMACMA_UnitdataEnable) + smc->mib.m[MAC0].fddiMACMA_UnitdataAvailable = TRUE ; + else + smc->mib.m[MAC0].fddiMACMA_UnitdataAvailable = FALSE ; + } + /*RM25*/ + else if (smc->r.dup_addr_test == DA_FAILED) { + smc->mib.m[MAC0].fddiMACMA_UnitdataAvailable = FALSE ; + smc->r.loop_avail = FALSE ; + smc->r.da_flag = TRUE ; + GO_STATE(RM5_RING_OP_DUP) ; + break ; + } + break ; + case ACTIONS(RM3_DETECT) : + start_rmt_timer0(smc,smc->s.mac_d_max*2,RM_TIMEOUT_D_MAX) ; + start_rmt_timer1(smc,smc->s.rmt_t_stuck,RM_TIMEOUT_T_STUCK) ; + start_rmt_timer2(smc,smc->s.rmt_t_poll,RM_TIMEOUT_POLL) ; + sm_mac_check_beacon_claim(smc) ; + DB_RMTN(1,"RMT : RM3_DETECT\n",0,0) ; + ACTIONS_DONE() ; + break ; + case RM3_DETECT : + if (cmd == RM_TIMEOUT_POLL) { + start_rmt_timer2(smc,smc->s.rmt_t_poll,RM_TIMEOUT_POLL); + sm_mac_check_beacon_claim(smc) ; + break ; + } + if (cmd == RM_TIMEOUT_D_MAX) { + smc->r.timer0_exp = TRUE ; + } + /* + *jd(22-Feb-1999) + * We need a time ">= 2*mac_d_max" since we had finished + * Claim or Beacon state. So we will restart timer0 at + * every state change. + */ + if (cmd == RM_TX_STATE_CHANGE) { + start_rmt_timer0(smc, + smc->s.mac_d_max*2, + RM_TIMEOUT_D_MAX) ; + } + /*RM32*/ + if (cmd == RM_RING_OP) { + GO_STATE(RM2_RING_OP) ; + break ; + } + /*RM33a*/ + else if ((cmd == RM_MY_BEACON || cmd == RM_OTHER_BEACON) + && smc->r.bn_flag) { + smc->r.bn_flag = FALSE ; + } + /*RM33b*/ + else if (cmd == RM_TRT_EXP && !smc->r.bn_flag) { + int tx ; + /* + * set bn_flag only if in state T4 or T5: + * only if we're the beaconer should we start the + * trace ! + */ + if ((tx = sm_mac_get_tx_state(smc)) == 4 || tx == 5) { + DB_RMTN(2,"RMT : DETECT && TRT_EXPIRED && T4/T5\n",0,0); + smc->r.bn_flag = TRUE ; + /* + * If one of the upstream stations beaconed + * and the link to the upstream neighbor is + * lost we need to restart the stuck timer to + * check the "stuck beacon" condition. + */ + start_rmt_timer1(smc,smc->s.rmt_t_stuck, + RM_TIMEOUT_T_STUCK) ; + } + /* + * We do NOT need to clear smc->r.bn_flag in case of + * not being in state T4 or T5, because the flag + * must be cleared in order to get in this condition. + */ + + DB_RMTN(2, + "RMT : sm_mac_get_tx_state() = %d (bn_flag = %d)\n", + tx,smc->r.bn_flag) ; + } + /*RM34a*/ + else if (cmd == RM_MY_CLAIM && smc->r.timer0_exp) { + rmt_new_dup_actions(smc) ; + GO_STATE(RM4_NON_OP_DUP) ; + break ; + } + /*RM34b*/ + else if (cmd == RM_MY_BEACON && smc->r.timer0_exp) { + rmt_new_dup_actions(smc) ; + GO_STATE(RM4_NON_OP_DUP) ; + break ; + } + /*RM34c*/ + else if (cmd == RM_VALID_CLAIM) { + rmt_new_dup_actions(smc) ; + GO_STATE(RM4_NON_OP_DUP) ; + break ; + } + /*RM36*/ + else if (cmd == RM_TIMEOUT_T_STUCK && + smc->r.rm_join && smc->r.bn_flag) { + GO_STATE(RM6_DIRECTED) ; + break ; + } + break ; + case ACTIONS(RM4_NON_OP_DUP) : + start_rmt_timer0(smc,smc->s.rmt_t_announce,RM_TIMEOUT_ANNOUNCE); + start_rmt_timer1(smc,smc->s.rmt_t_stuck,RM_TIMEOUT_T_STUCK) ; + start_rmt_timer2(smc,smc->s.rmt_t_poll,RM_TIMEOUT_POLL) ; + sm_mac_check_beacon_claim(smc) ; + DB_RMTN(1,"RMT : RM4_NON_OP_DUP\n",0,0) ; + ACTIONS_DONE() ; + break ; + case RM4_NON_OP_DUP : + if (cmd == RM_TIMEOUT_POLL) { + start_rmt_timer2(smc,smc->s.rmt_t_poll,RM_TIMEOUT_POLL); + sm_mac_check_beacon_claim(smc) ; + break ; + } + /*RM41*/ + if (!smc->r.da_flag) { + GO_STATE(RM1_NON_OP) ; + break ; + } + /*RM44a*/ + else if ((cmd == RM_MY_BEACON || cmd == RM_OTHER_BEACON) && + smc->r.bn_flag) { + smc->r.bn_flag = FALSE ; + } + /*RM44b*/ + else if (cmd == RM_TRT_EXP && !smc->r.bn_flag) { + int tx ; + /* + * set bn_flag only if in state T4 or T5: + * only if we're the beaconer should we start the + * trace ! + */ + if ((tx = sm_mac_get_tx_state(smc)) == 4 || tx == 5) { + DB_RMTN(2,"RMT : NOPDUP && TRT_EXPIRED && T4/T5\n",0,0); + smc->r.bn_flag = TRUE ; + /* + * If one of the upstream stations beaconed + * and the link to the upstream neighbor is + * lost we need to restart the stuck timer to + * check the "stuck beacon" condition. + */ + start_rmt_timer1(smc,smc->s.rmt_t_stuck, + RM_TIMEOUT_T_STUCK) ; + } + /* + * We do NOT need to clear smc->r.bn_flag in case of + * not being in state T4 or T5, because the flag + * must be cleared in order to get in this condition. + */ + + DB_RMTN(2, + "RMT : sm_mac_get_tx_state() = %d (bn_flag = %d)\n", + tx,smc->r.bn_flag) ; + } + /*RM44c*/ + else if (cmd == RM_TIMEOUT_ANNOUNCE && !smc->r.bn_flag) { + rmt_dup_actions(smc) ; + } + /*RM45*/ + else if (cmd == RM_RING_OP) { + smc->r.no_flag = FALSE ; + GO_STATE(RM5_RING_OP_DUP) ; + break ; + } + /*RM46*/ + else if (cmd == RM_TIMEOUT_T_STUCK && + smc->r.rm_join && smc->r.bn_flag) { + GO_STATE(RM6_DIRECTED) ; + break ; + } + break ; + case ACTIONS(RM5_RING_OP_DUP) : + stop_rmt_timer0(smc) ; + stop_rmt_timer1(smc) ; + stop_rmt_timer2(smc) ; + DB_RMTN(1,"RMT : RM5_RING_OP_DUP\n",0,0) ; + ACTIONS_DONE() ; + break; + case RM5_RING_OP_DUP : + /*RM52*/ + if (smc->r.dup_addr_test == DA_PASSED) { + smc->r.da_flag = FALSE ; + GO_STATE(RM2_RING_OP) ; + break ; + } + /*RM54*/ + else if (cmd == RM_RING_NON_OP) { + smc->r.jm_flag = FALSE ; + smc->r.bn_flag = FALSE ; + GO_STATE(RM4_NON_OP_DUP) ; + break ; + } + break ; + case ACTIONS(RM6_DIRECTED) : + start_rmt_timer0(smc,smc->s.rmt_t_direct,RM_TIMEOUT_T_DIRECT) ; + stop_rmt_timer1(smc) ; + start_rmt_timer2(smc,smc->s.rmt_t_poll,RM_TIMEOUT_POLL) ; + sm_ma_control(smc,MA_DIRECTED) ; + RS_SET(smc,RS_BEACON) ; + DB_RMTN(1,"RMT : RM6_DIRECTED\n",0,0) ; + ACTIONS_DONE() ; + break ; + case RM6_DIRECTED : + /*RM63*/ + if (cmd == RM_TIMEOUT_POLL) { + start_rmt_timer2(smc,smc->s.rmt_t_poll,RM_TIMEOUT_POLL); + sm_mac_check_beacon_claim(smc) ; +#ifndef SUPERNET_3 + /* Because of problems with the Supernet II chip set + * sending of Directed Beacon will stop after 165ms + * therefore restart_trt_for_dbcn(smc) will be called + * to prevent this. + */ + restart_trt_for_dbcn(smc) ; +#endif /*SUPERNET_3*/ + break ; + } + if ((cmd == RM_MY_BEACON || cmd == RM_OTHER_BEACON) && + !smc->r.da_flag) { + smc->r.bn_flag = FALSE ; + GO_STATE(RM3_DETECT) ; + break ; + } + /*RM64*/ + else if ((cmd == RM_MY_BEACON || cmd == RM_OTHER_BEACON) && + smc->r.da_flag) { + smc->r.bn_flag = FALSE ; + GO_STATE(RM4_NON_OP_DUP) ; + break ; + } + /*RM67*/ + else if (cmd == RM_TIMEOUT_T_DIRECT) { + GO_STATE(RM7_TRACE) ; + break ; + } + break ; + case ACTIONS(RM7_TRACE) : + stop_rmt_timer0(smc) ; + stop_rmt_timer1(smc) ; + stop_rmt_timer2(smc) ; + smc->e.trace_prop |= ENTITY_BIT(ENTITY_MAC) ; + queue_event(smc,EVENT_ECM,EC_TRACE_PROP) ; + DB_RMTN(1,"RMT : RM7_TRACE\n",0,0) ; + ACTIONS_DONE() ; + break ; + case RM7_TRACE : + break ; + default: + SMT_PANIC(smc,SMT_E0122, SMT_E0122_MSG) ; + break; + } +} + +/* + * (jd) RMT duplicate address actions + * leave the ring or reinsert just as configured + */ +static void rmt_dup_actions(struct s_smc *smc) +{ + if (smc->r.jm_flag) { + } + else { + if (smc->s.rmt_dup_mac_behavior) { + SMT_ERR_LOG(smc,SMT_E0138, SMT_E0138_MSG) ; + rmt_reinsert_actions(smc) ; + } + else { + SMT_ERR_LOG(smc,SMT_E0135, SMT_E0135_MSG) ; + rmt_leave_actions(smc) ; + } + } +} + +/* + * Reconnect to the Ring + */ +static void rmt_reinsert_actions(struct s_smc *smc) +{ + queue_event(smc,EVENT_ECM,EC_DISCONNECT) ; + queue_event(smc,EVENT_ECM,EC_CONNECT) ; +} + +/* + * duplicate address detected + */ +static void rmt_new_dup_actions(struct s_smc *smc) +{ + smc->r.da_flag = TRUE ; + smc->r.bn_flag = FALSE ; + smc->r.jm_flag = FALSE ; + /* + * we have three options : change address, jam or leave + * we leave the ring as default + * Optionally it's possible to reinsert after leaving the Ring + * but this will not conform with SMT Spec. + */ + if (smc->s.rmt_dup_mac_behavior) { + SMT_ERR_LOG(smc,SMT_E0138, SMT_E0138_MSG) ; + rmt_reinsert_actions(smc) ; + } + else { + SMT_ERR_LOG(smc,SMT_E0135, SMT_E0135_MSG) ; + rmt_leave_actions(smc) ; + } +} + + +/* + * leave the ring + */ +static void rmt_leave_actions(struct s_smc *smc) +{ + queue_event(smc,EVENT_ECM,EC_DISCONNECT) ; + /* + * Note: Do NOT try again later. (with please reconnect) + * The station must be left from the ring! + */ +} + +/* + * SMT timer interface + * start RMT timer 0 + */ +static void start_rmt_timer0(struct s_smc *smc, u_long value, int event) +{ + smc->r.timer0_exp = FALSE ; /* clear timer event flag */ + smt_timer_start(smc,&smc->r.rmt_timer0,value,EV_TOKEN(EVENT_RMT,event)); +} + +/* + * SMT timer interface + * start RMT timer 1 + */ +static void start_rmt_timer1(struct s_smc *smc, u_long value, int event) +{ + smc->r.timer1_exp = FALSE ; /* clear timer event flag */ + smt_timer_start(smc,&smc->r.rmt_timer1,value,EV_TOKEN(EVENT_RMT,event)); +} + +/* + * SMT timer interface + * start RMT timer 2 + */ +static void start_rmt_timer2(struct s_smc *smc, u_long value, int event) +{ + smc->r.timer2_exp = FALSE ; /* clear timer event flag */ + smt_timer_start(smc,&smc->r.rmt_timer2,value,EV_TOKEN(EVENT_RMT,event)); +} + +/* + * SMT timer interface + * stop RMT timer 0 + */ +static void stop_rmt_timer0(struct s_smc *smc) +{ + if (smc->r.rmt_timer0.tm_active) + smt_timer_stop(smc,&smc->r.rmt_timer0) ; +} + +/* + * SMT timer interface + * stop RMT timer 1 + */ +static void stop_rmt_timer1(struct s_smc *smc) +{ + if (smc->r.rmt_timer1.tm_active) + smt_timer_stop(smc,&smc->r.rmt_timer1) ; +} + +/* + * SMT timer interface + * stop RMT timer 2 + */ +static void stop_rmt_timer2(struct s_smc *smc) +{ + if (smc->r.rmt_timer2.tm_active) + smt_timer_stop(smc,&smc->r.rmt_timer2) ; +} + diff --git a/kernel/drivers/net/fddi/skfp/skfddi.c b/kernel/drivers/net/fddi/skfp/skfddi.c new file mode 100644 index 000000000..51acc6d86 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/skfddi.c @@ -0,0 +1,2248 @@ +/* + * File Name: + * skfddi.c + * + * Copyright Information: + * Copyright SysKonnect 1998,1999. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + * Abstract: + * A Linux device driver supporting the SysKonnect FDDI PCI controller + * familie. + * + * Maintainers: + * CG Christoph Goos (cgoos@syskonnect.de) + * + * Contributors: + * DM David S. Miller + * + * Address all question to: + * linux@syskonnect.de + * + * The technical manual for the adapters is available from SysKonnect's + * web pages: www.syskonnect.com + * Goto "Support" and search Knowledge Base for "manual". + * + * Driver Architecture: + * The driver architecture is based on the DEC FDDI driver by + * Lawrence V. Stefani and several ethernet drivers. + * I also used an existing Windows NT miniport driver. + * All hardware dependent functions are handled by the SysKonnect + * Hardware Module. + * The only headerfiles that are directly related to this source + * are skfddi.c, h/types.h, h/osdef1st.h, h/targetos.h. + * The others belong to the SysKonnect FDDI Hardware Module and + * should better not be changed. + * + * Modification History: + * Date Name Description + * 02-Mar-98 CG Created. + * + * 10-Mar-99 CG Support for 2.2.x added. + * 25-Mar-99 CG Corrected IRQ routing for SMP (APIC) + * 26-Oct-99 CG Fixed compilation error on 2.2.13 + * 12-Nov-99 CG Source code release + * 22-Nov-99 CG Included in kernel source. + * 07-May-00 DM 64 bit fixes, new dma interface + * 31-Jul-03 DB Audit copy_*_user in skfp_ioctl + * Daniele Bellucci <bellucda@tiscali.it> + * 03-Dec-03 SH Convert to PCI device model + * + * Compilation options (-Dxxx): + * DRIVERDEBUG print lots of messages to log file + * DUMPPACKETS print received/transmitted packets to logfile + * + * Tested cpu architectures: + * - i386 + * - sparc64 + */ + +/* Version information string - should be updated prior to */ +/* each new release!!! */ +#define VERSION "2.07" + +static const char * const boot_msg = + "SysKonnect FDDI PCI Adapter driver v" VERSION " for\n" + " SK-55xx/SK-58xx adapters (SK-NET FDDI-FP/UP/LP)"; + +/* Include files */ + +#include <linux/capability.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/ioport.h> +#include <linux/interrupt.h> +#include <linux/pci.h> +#include <linux/netdevice.h> +#include <linux/fddidevice.h> +#include <linux/skbuff.h> +#include <linux/bitops.h> +#include <linux/gfp.h> + +#include <asm/byteorder.h> +#include <asm/io.h> +#include <asm/uaccess.h> + +#include "h/types.h" +#undef ADDR // undo Linux definition +#include "h/skfbi.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/smtstate.h" + + +// Define module-wide (static) routines +static int skfp_driver_init(struct net_device *dev); +static int skfp_open(struct net_device *dev); +static int skfp_close(struct net_device *dev); +static irqreturn_t skfp_interrupt(int irq, void *dev_id); +static struct net_device_stats *skfp_ctl_get_stats(struct net_device *dev); +static void skfp_ctl_set_multicast_list(struct net_device *dev); +static void skfp_ctl_set_multicast_list_wo_lock(struct net_device *dev); +static int skfp_ctl_set_mac_address(struct net_device *dev, void *addr); +static int skfp_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); +static netdev_tx_t skfp_send_pkt(struct sk_buff *skb, + struct net_device *dev); +static void send_queued_packets(struct s_smc *smc); +static void CheckSourceAddress(unsigned char *frame, unsigned char *hw_addr); +static void ResetAdapter(struct s_smc *smc); + + +// Functions needed by the hardware module +void *mac_drv_get_space(struct s_smc *smc, u_int size); +void *mac_drv_get_desc_mem(struct s_smc *smc, u_int size); +unsigned long mac_drv_virt2phys(struct s_smc *smc, void *virt); +unsigned long dma_master(struct s_smc *smc, void *virt, int len, int flag); +void dma_complete(struct s_smc *smc, volatile union s_fp_descr *descr, + int flag); +void mac_drv_tx_complete(struct s_smc *smc, volatile struct s_smt_fp_txd *txd); +void llc_restart_tx(struct s_smc *smc); +void mac_drv_rx_complete(struct s_smc *smc, volatile struct s_smt_fp_rxd *rxd, + int frag_count, int len); +void mac_drv_requeue_rxd(struct s_smc *smc, volatile struct s_smt_fp_rxd *rxd, + int frag_count); +void mac_drv_fill_rxd(struct s_smc *smc); +void mac_drv_clear_rxd(struct s_smc *smc, volatile struct s_smt_fp_rxd *rxd, + int frag_count); +int mac_drv_rx_init(struct s_smc *smc, int len, int fc, char *look_ahead, + int la_len); +void dump_data(unsigned char *Data, int length); + +// External functions from the hardware module +extern u_int mac_drv_check_space(void); +extern int mac_drv_init(struct s_smc *smc); +extern void hwm_tx_frag(struct s_smc *smc, char far * virt, u_long phys, + int len, int frame_status); +extern int hwm_tx_init(struct s_smc *smc, u_char fc, int frag_count, + int frame_len, int frame_status); +extern void fddi_isr(struct s_smc *smc); +extern void hwm_rx_frag(struct s_smc *smc, char far * virt, u_long phys, + int len, int frame_status); +extern void mac_drv_rx_mode(struct s_smc *smc, int mode); +extern void mac_drv_clear_rx_queue(struct s_smc *smc); +extern void enable_tx_irq(struct s_smc *smc, u_short queue); + +static const struct pci_device_id skfddi_pci_tbl[] = { + { PCI_VENDOR_ID_SK, PCI_DEVICE_ID_SK_FP, PCI_ANY_ID, PCI_ANY_ID, }, + { } /* Terminating entry */ +}; +MODULE_DEVICE_TABLE(pci, skfddi_pci_tbl); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Mirko Lindner <mlindner@syskonnect.de>"); + +// Define module-wide (static) variables + +static int num_boards; /* total number of adapters configured */ + +static const struct net_device_ops skfp_netdev_ops = { + .ndo_open = skfp_open, + .ndo_stop = skfp_close, + .ndo_start_xmit = skfp_send_pkt, + .ndo_get_stats = skfp_ctl_get_stats, + .ndo_change_mtu = fddi_change_mtu, + .ndo_set_rx_mode = skfp_ctl_set_multicast_list, + .ndo_set_mac_address = skfp_ctl_set_mac_address, + .ndo_do_ioctl = skfp_ioctl, +}; + +/* + * ================= + * = skfp_init_one = + * ================= + * + * Overview: + * Probes for supported FDDI PCI controllers + * + * Returns: + * Condition code + * + * Arguments: + * pdev - pointer to PCI device information + * + * Functional Description: + * This is now called by PCI driver registration process + * for each board found. + * + * Return Codes: + * 0 - This device (fddi0, fddi1, etc) configured successfully + * -ENODEV - No devices present, or no SysKonnect FDDI PCI device + * present for this device name + * + * + * Side Effects: + * Device structures for FDDI adapters (fddi0, fddi1, etc) are + * initialized and the board resources are read and stored in + * the device structure. + */ +static int skfp_init_one(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct net_device *dev; + struct s_smc *smc; /* board pointer */ + void __iomem *mem; + int err; + + pr_debug("entering skfp_init_one\n"); + + if (num_boards == 0) + printk("%s\n", boot_msg); + + err = pci_enable_device(pdev); + if (err) + return err; + + err = pci_request_regions(pdev, "skfddi"); + if (err) + goto err_out1; + + pci_set_master(pdev); + +#ifdef MEM_MAPPED_IO + if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) { + printk(KERN_ERR "skfp: region is not an MMIO resource\n"); + err = -EIO; + goto err_out2; + } + + mem = ioremap(pci_resource_start(pdev, 0), 0x4000); +#else + if (!(pci_resource_flags(pdev, 1) & IO_RESOURCE_IO)) { + printk(KERN_ERR "skfp: region is not PIO resource\n"); + err = -EIO; + goto err_out2; + } + + mem = ioport_map(pci_resource_start(pdev, 1), FP_IO_LEN); +#endif + if (!mem) { + printk(KERN_ERR "skfp: Unable to map register, " + "FDDI adapter will be disabled.\n"); + err = -EIO; + goto err_out2; + } + + dev = alloc_fddidev(sizeof(struct s_smc)); + if (!dev) { + printk(KERN_ERR "skfp: Unable to allocate fddi device, " + "FDDI adapter will be disabled.\n"); + err = -ENOMEM; + goto err_out3; + } + + dev->irq = pdev->irq; + dev->netdev_ops = &skfp_netdev_ops; + + SET_NETDEV_DEV(dev, &pdev->dev); + + /* Initialize board structure with bus-specific info */ + smc = netdev_priv(dev); + smc->os.dev = dev; + smc->os.bus_type = SK_BUS_TYPE_PCI; + smc->os.pdev = *pdev; + smc->os.QueueSkb = MAX_TX_QUEUE_LEN; + smc->os.MaxFrameSize = MAX_FRAME_SIZE; + smc->os.dev = dev; + smc->hw.slot = -1; + smc->hw.iop = mem; + smc->os.ResetRequested = FALSE; + skb_queue_head_init(&smc->os.SendSkbQueue); + + dev->base_addr = (unsigned long)mem; + + err = skfp_driver_init(dev); + if (err) + goto err_out4; + + err = register_netdev(dev); + if (err) + goto err_out5; + + ++num_boards; + pci_set_drvdata(pdev, dev); + + if ((pdev->subsystem_device & 0xff00) == 0x5500 || + (pdev->subsystem_device & 0xff00) == 0x5800) + printk("%s: SysKonnect FDDI PCI adapter" + " found (SK-%04X)\n", dev->name, + pdev->subsystem_device); + else + printk("%s: FDDI PCI adapter found\n", dev->name); + + return 0; +err_out5: + if (smc->os.SharedMemAddr) + pci_free_consistent(pdev, smc->os.SharedMemSize, + smc->os.SharedMemAddr, + smc->os.SharedMemDMA); + pci_free_consistent(pdev, MAX_FRAME_SIZE, + smc->os.LocalRxBuffer, smc->os.LocalRxBufferDMA); +err_out4: + free_netdev(dev); +err_out3: +#ifdef MEM_MAPPED_IO + iounmap(mem); +#else + ioport_unmap(mem); +#endif +err_out2: + pci_release_regions(pdev); +err_out1: + pci_disable_device(pdev); + return err; +} + +/* + * Called for each adapter board from pci_unregister_driver + */ +static void skfp_remove_one(struct pci_dev *pdev) +{ + struct net_device *p = pci_get_drvdata(pdev); + struct s_smc *lp = netdev_priv(p); + + unregister_netdev(p); + + if (lp->os.SharedMemAddr) { + pci_free_consistent(&lp->os.pdev, + lp->os.SharedMemSize, + lp->os.SharedMemAddr, + lp->os.SharedMemDMA); + lp->os.SharedMemAddr = NULL; + } + if (lp->os.LocalRxBuffer) { + pci_free_consistent(&lp->os.pdev, + MAX_FRAME_SIZE, + lp->os.LocalRxBuffer, + lp->os.LocalRxBufferDMA); + lp->os.LocalRxBuffer = NULL; + } +#ifdef MEM_MAPPED_IO + iounmap(lp->hw.iop); +#else + ioport_unmap(lp->hw.iop); +#endif + pci_release_regions(pdev); + free_netdev(p); + + pci_disable_device(pdev); +} + +/* + * ==================== + * = skfp_driver_init = + * ==================== + * + * Overview: + * Initializes remaining adapter board structure information + * and makes sure adapter is in a safe state prior to skfp_open(). + * + * Returns: + * Condition code + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * This function allocates additional resources such as the host memory + * blocks needed by the adapter. + * The adapter is also reset. The OS must call skfp_open() to open + * the adapter and bring it on-line. + * + * Return Codes: + * 0 - initialization succeeded + * -1 - initialization failed + */ +static int skfp_driver_init(struct net_device *dev) +{ + struct s_smc *smc = netdev_priv(dev); + skfddi_priv *bp = &smc->os; + int err = -EIO; + + pr_debug("entering skfp_driver_init\n"); + + // set the io address in private structures + bp->base_addr = dev->base_addr; + + // Get the interrupt level from the PCI Configuration Table + smc->hw.irq = dev->irq; + + spin_lock_init(&bp->DriverLock); + + // Allocate invalid frame + bp->LocalRxBuffer = pci_alloc_consistent(&bp->pdev, MAX_FRAME_SIZE, &bp->LocalRxBufferDMA); + if (!bp->LocalRxBuffer) { + printk("could not allocate mem for "); + printk("LocalRxBuffer: %d byte\n", MAX_FRAME_SIZE); + goto fail; + } + + // Determine the required size of the 'shared' memory area. + bp->SharedMemSize = mac_drv_check_space(); + pr_debug("Memory for HWM: %ld\n", bp->SharedMemSize); + if (bp->SharedMemSize > 0) { + bp->SharedMemSize += 16; // for descriptor alignment + + bp->SharedMemAddr = pci_alloc_consistent(&bp->pdev, + bp->SharedMemSize, + &bp->SharedMemDMA); + if (!bp->SharedMemAddr) { + printk("could not allocate mem for "); + printk("hardware module: %ld byte\n", + bp->SharedMemSize); + goto fail; + } + bp->SharedMemHeap = 0; // Nothing used yet. + + } else { + bp->SharedMemAddr = NULL; + bp->SharedMemHeap = 0; + } // SharedMemSize > 0 + + memset(bp->SharedMemAddr, 0, bp->SharedMemSize); + + card_stop(smc); // Reset adapter. + + pr_debug("mac_drv_init()..\n"); + if (mac_drv_init(smc) != 0) { + pr_debug("mac_drv_init() failed\n"); + goto fail; + } + read_address(smc, NULL); + pr_debug("HW-Addr: %pMF\n", smc->hw.fddi_canon_addr.a); + memcpy(dev->dev_addr, smc->hw.fddi_canon_addr.a, ETH_ALEN); + + smt_reset_defaults(smc, 0); + + return 0; + +fail: + if (bp->SharedMemAddr) { + pci_free_consistent(&bp->pdev, + bp->SharedMemSize, + bp->SharedMemAddr, + bp->SharedMemDMA); + bp->SharedMemAddr = NULL; + } + if (bp->LocalRxBuffer) { + pci_free_consistent(&bp->pdev, MAX_FRAME_SIZE, + bp->LocalRxBuffer, bp->LocalRxBufferDMA); + bp->LocalRxBuffer = NULL; + } + return err; +} // skfp_driver_init + + +/* + * ============= + * = skfp_open = + * ============= + * + * Overview: + * Opens the adapter + * + * Returns: + * Condition code + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * This function brings the adapter to an operational state. + * + * Return Codes: + * 0 - Adapter was successfully opened + * -EAGAIN - Could not register IRQ + */ +static int skfp_open(struct net_device *dev) +{ + struct s_smc *smc = netdev_priv(dev); + int err; + + pr_debug("entering skfp_open\n"); + /* Register IRQ - support shared interrupts by passing device ptr */ + err = request_irq(dev->irq, skfp_interrupt, IRQF_SHARED, + dev->name, dev); + if (err) + return err; + + /* + * Set current address to factory MAC address + * + * Note: We've already done this step in skfp_driver_init. + * However, it's possible that a user has set a node + * address override, then closed and reopened the + * adapter. Unless we reset the device address field + * now, we'll continue to use the existing modified + * address. + */ + read_address(smc, NULL); + memcpy(dev->dev_addr, smc->hw.fddi_canon_addr.a, ETH_ALEN); + + init_smt(smc, NULL); + smt_online(smc, 1); + STI_FBI(); + + /* Clear local multicast address tables */ + mac_clear_multicast(smc); + + /* Disable promiscuous filter settings */ + mac_drv_rx_mode(smc, RX_DISABLE_PROMISC); + + netif_start_queue(dev); + return 0; +} // skfp_open + + +/* + * ============== + * = skfp_close = + * ============== + * + * Overview: + * Closes the device/module. + * + * Returns: + * Condition code + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * This routine closes the adapter and brings it to a safe state. + * The interrupt service routine is deregistered with the OS. + * The adapter can be opened again with another call to skfp_open(). + * + * Return Codes: + * Always return 0. + * + * Assumptions: + * No further requests for this adapter are made after this routine is + * called. skfp_open() can be called to reset and reinitialize the + * adapter. + */ +static int skfp_close(struct net_device *dev) +{ + struct s_smc *smc = netdev_priv(dev); + skfddi_priv *bp = &smc->os; + + CLI_FBI(); + smt_reset_defaults(smc, 1); + card_stop(smc); + mac_drv_clear_tx_queue(smc); + mac_drv_clear_rx_queue(smc); + + netif_stop_queue(dev); + /* Deregister (free) IRQ */ + free_irq(dev->irq, dev); + + skb_queue_purge(&bp->SendSkbQueue); + bp->QueueSkb = MAX_TX_QUEUE_LEN; + + return 0; +} // skfp_close + + +/* + * ================== + * = skfp_interrupt = + * ================== + * + * Overview: + * Interrupt processing routine + * + * Returns: + * None + * + * Arguments: + * irq - interrupt vector + * dev_id - pointer to device information + * + * Functional Description: + * This routine calls the interrupt processing routine for this adapter. It + * disables and reenables adapter interrupts, as appropriate. We can support + * shared interrupts since the incoming dev_id pointer provides our device + * structure context. All the real work is done in the hardware module. + * + * Return Codes: + * None + * + * Assumptions: + * The interrupt acknowledgement at the hardware level (eg. ACKing the PIC + * on Intel-based systems) is done by the operating system outside this + * routine. + * + * System interrupts are enabled through this call. + * + * Side Effects: + * Interrupts are disabled, then reenabled at the adapter. + */ + +static irqreturn_t skfp_interrupt(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct s_smc *smc; /* private board structure pointer */ + skfddi_priv *bp; + + smc = netdev_priv(dev); + bp = &smc->os; + + // IRQs enabled or disabled ? + if (inpd(ADDR(B0_IMSK)) == 0) { + // IRQs are disabled: must be shared interrupt + return IRQ_NONE; + } + // Note: At this point, IRQs are enabled. + if ((inpd(ISR_A) & smc->hw.is_imask) == 0) { // IRQ? + // Adapter did not issue an IRQ: must be shared interrupt + return IRQ_NONE; + } + CLI_FBI(); // Disable IRQs from our adapter. + spin_lock(&bp->DriverLock); + + // Call interrupt handler in hardware module (HWM). + fddi_isr(smc); + + if (smc->os.ResetRequested) { + ResetAdapter(smc); + smc->os.ResetRequested = FALSE; + } + spin_unlock(&bp->DriverLock); + STI_FBI(); // Enable IRQs from our adapter. + + return IRQ_HANDLED; +} // skfp_interrupt + + +/* + * ====================== + * = skfp_ctl_get_stats = + * ====================== + * + * Overview: + * Get statistics for FDDI adapter + * + * Returns: + * Pointer to FDDI statistics structure + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * Gets current MIB objects from adapter, then + * returns FDDI statistics structure as defined + * in if_fddi.h. + * + * Note: Since the FDDI statistics structure is + * still new and the device structure doesn't + * have an FDDI-specific get statistics handler, + * we'll return the FDDI statistics structure as + * a pointer to an Ethernet statistics structure. + * That way, at least the first part of the statistics + * structure can be decoded properly. + * We'll have to pay attention to this routine as the + * device structure becomes more mature and LAN media + * independent. + * + */ +static struct net_device_stats *skfp_ctl_get_stats(struct net_device *dev) +{ + struct s_smc *bp = netdev_priv(dev); + + /* Fill the bp->stats structure with driver-maintained counters */ + + bp->os.MacStat.port_bs_flag[0] = 0x1234; + bp->os.MacStat.port_bs_flag[1] = 0x5678; +// goos: need to fill out fddi statistic +#if 0 + /* Get FDDI SMT MIB objects */ + +/* Fill the bp->stats structure with the SMT MIB object values */ + + memcpy(bp->stats.smt_station_id, &bp->cmd_rsp_virt->smt_mib_get.smt_station_id, sizeof(bp->cmd_rsp_virt->smt_mib_get.smt_station_id)); + bp->stats.smt_op_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_op_version_id; + bp->stats.smt_hi_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_hi_version_id; + bp->stats.smt_lo_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_lo_version_id; + memcpy(bp->stats.smt_user_data, &bp->cmd_rsp_virt->smt_mib_get.smt_user_data, sizeof(bp->cmd_rsp_virt->smt_mib_get.smt_user_data)); + bp->stats.smt_mib_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_mib_version_id; + bp->stats.smt_mac_cts = bp->cmd_rsp_virt->smt_mib_get.smt_mac_ct; + bp->stats.smt_non_master_cts = bp->cmd_rsp_virt->smt_mib_get.smt_non_master_ct; + bp->stats.smt_master_cts = bp->cmd_rsp_virt->smt_mib_get.smt_master_ct; + bp->stats.smt_available_paths = bp->cmd_rsp_virt->smt_mib_get.smt_available_paths; + bp->stats.smt_config_capabilities = bp->cmd_rsp_virt->smt_mib_get.smt_config_capabilities; + bp->stats.smt_config_policy = bp->cmd_rsp_virt->smt_mib_get.smt_config_policy; + bp->stats.smt_connection_policy = bp->cmd_rsp_virt->smt_mib_get.smt_connection_policy; + bp->stats.smt_t_notify = bp->cmd_rsp_virt->smt_mib_get.smt_t_notify; + bp->stats.smt_stat_rpt_policy = bp->cmd_rsp_virt->smt_mib_get.smt_stat_rpt_policy; + bp->stats.smt_trace_max_expiration = bp->cmd_rsp_virt->smt_mib_get.smt_trace_max_expiration; + bp->stats.smt_bypass_present = bp->cmd_rsp_virt->smt_mib_get.smt_bypass_present; + bp->stats.smt_ecm_state = bp->cmd_rsp_virt->smt_mib_get.smt_ecm_state; + bp->stats.smt_cf_state = bp->cmd_rsp_virt->smt_mib_get.smt_cf_state; + bp->stats.smt_remote_disconnect_flag = bp->cmd_rsp_virt->smt_mib_get.smt_remote_disconnect_flag; + bp->stats.smt_station_status = bp->cmd_rsp_virt->smt_mib_get.smt_station_status; + bp->stats.smt_peer_wrap_flag = bp->cmd_rsp_virt->smt_mib_get.smt_peer_wrap_flag; + bp->stats.smt_time_stamp = bp->cmd_rsp_virt->smt_mib_get.smt_msg_time_stamp.ls; + bp->stats.smt_transition_time_stamp = bp->cmd_rsp_virt->smt_mib_get.smt_transition_time_stamp.ls; + bp->stats.mac_frame_status_functions = bp->cmd_rsp_virt->smt_mib_get.mac_frame_status_functions; + bp->stats.mac_t_max_capability = bp->cmd_rsp_virt->smt_mib_get.mac_t_max_capability; + bp->stats.mac_tvx_capability = bp->cmd_rsp_virt->smt_mib_get.mac_tvx_capability; + bp->stats.mac_available_paths = bp->cmd_rsp_virt->smt_mib_get.mac_available_paths; + bp->stats.mac_current_path = bp->cmd_rsp_virt->smt_mib_get.mac_current_path; + memcpy(bp->stats.mac_upstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_upstream_nbr, FDDI_K_ALEN); + memcpy(bp->stats.mac_downstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_downstream_nbr, FDDI_K_ALEN); + memcpy(bp->stats.mac_old_upstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_old_upstream_nbr, FDDI_K_ALEN); + memcpy(bp->stats.mac_old_downstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_old_downstream_nbr, FDDI_K_ALEN); + bp->stats.mac_dup_address_test = bp->cmd_rsp_virt->smt_mib_get.mac_dup_address_test; + bp->stats.mac_requested_paths = bp->cmd_rsp_virt->smt_mib_get.mac_requested_paths; + bp->stats.mac_downstream_port_type = bp->cmd_rsp_virt->smt_mib_get.mac_downstream_port_type; + memcpy(bp->stats.mac_smt_address, &bp->cmd_rsp_virt->smt_mib_get.mac_smt_address, FDDI_K_ALEN); + bp->stats.mac_t_req = bp->cmd_rsp_virt->smt_mib_get.mac_t_req; + bp->stats.mac_t_neg = bp->cmd_rsp_virt->smt_mib_get.mac_t_neg; + bp->stats.mac_t_max = bp->cmd_rsp_virt->smt_mib_get.mac_t_max; + bp->stats.mac_tvx_value = bp->cmd_rsp_virt->smt_mib_get.mac_tvx_value; + bp->stats.mac_frame_error_threshold = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_threshold; + bp->stats.mac_frame_error_ratio = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_ratio; + bp->stats.mac_rmt_state = bp->cmd_rsp_virt->smt_mib_get.mac_rmt_state; + bp->stats.mac_da_flag = bp->cmd_rsp_virt->smt_mib_get.mac_da_flag; + bp->stats.mac_una_da_flag = bp->cmd_rsp_virt->smt_mib_get.mac_unda_flag; + bp->stats.mac_frame_error_flag = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_flag; + bp->stats.mac_ma_unitdata_available = bp->cmd_rsp_virt->smt_mib_get.mac_ma_unitdata_available; + bp->stats.mac_hardware_present = bp->cmd_rsp_virt->smt_mib_get.mac_hardware_present; + bp->stats.mac_ma_unitdata_enable = bp->cmd_rsp_virt->smt_mib_get.mac_ma_unitdata_enable; + bp->stats.path_tvx_lower_bound = bp->cmd_rsp_virt->smt_mib_get.path_tvx_lower_bound; + bp->stats.path_t_max_lower_bound = bp->cmd_rsp_virt->smt_mib_get.path_t_max_lower_bound; + bp->stats.path_max_t_req = bp->cmd_rsp_virt->smt_mib_get.path_max_t_req; + memcpy(bp->stats.path_configuration, &bp->cmd_rsp_virt->smt_mib_get.path_configuration, sizeof(bp->cmd_rsp_virt->smt_mib_get.path_configuration)); + bp->stats.port_my_type[0] = bp->cmd_rsp_virt->smt_mib_get.port_my_type[0]; + bp->stats.port_my_type[1] = bp->cmd_rsp_virt->smt_mib_get.port_my_type[1]; + bp->stats.port_neighbor_type[0] = bp->cmd_rsp_virt->smt_mib_get.port_neighbor_type[0]; + bp->stats.port_neighbor_type[1] = bp->cmd_rsp_virt->smt_mib_get.port_neighbor_type[1]; + bp->stats.port_connection_policies[0] = bp->cmd_rsp_virt->smt_mib_get.port_connection_policies[0]; + bp->stats.port_connection_policies[1] = bp->cmd_rsp_virt->smt_mib_get.port_connection_policies[1]; + bp->stats.port_mac_indicated[0] = bp->cmd_rsp_virt->smt_mib_get.port_mac_indicated[0]; + bp->stats.port_mac_indicated[1] = bp->cmd_rsp_virt->smt_mib_get.port_mac_indicated[1]; + bp->stats.port_current_path[0] = bp->cmd_rsp_virt->smt_mib_get.port_current_path[0]; + bp->stats.port_current_path[1] = bp->cmd_rsp_virt->smt_mib_get.port_current_path[1]; + memcpy(&bp->stats.port_requested_paths[0 * 3], &bp->cmd_rsp_virt->smt_mib_get.port_requested_paths[0], 3); + memcpy(&bp->stats.port_requested_paths[1 * 3], &bp->cmd_rsp_virt->smt_mib_get.port_requested_paths[1], 3); + bp->stats.port_mac_placement[0] = bp->cmd_rsp_virt->smt_mib_get.port_mac_placement[0]; + bp->stats.port_mac_placement[1] = bp->cmd_rsp_virt->smt_mib_get.port_mac_placement[1]; + bp->stats.port_available_paths[0] = bp->cmd_rsp_virt->smt_mib_get.port_available_paths[0]; + bp->stats.port_available_paths[1] = bp->cmd_rsp_virt->smt_mib_get.port_available_paths[1]; + bp->stats.port_pmd_class[0] = bp->cmd_rsp_virt->smt_mib_get.port_pmd_class[0]; + bp->stats.port_pmd_class[1] = bp->cmd_rsp_virt->smt_mib_get.port_pmd_class[1]; + bp->stats.port_connection_capabilities[0] = bp->cmd_rsp_virt->smt_mib_get.port_connection_capabilities[0]; + bp->stats.port_connection_capabilities[1] = bp->cmd_rsp_virt->smt_mib_get.port_connection_capabilities[1]; + bp->stats.port_bs_flag[0] = bp->cmd_rsp_virt->smt_mib_get.port_bs_flag[0]; + bp->stats.port_bs_flag[1] = bp->cmd_rsp_virt->smt_mib_get.port_bs_flag[1]; + bp->stats.port_ler_estimate[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_estimate[0]; + bp->stats.port_ler_estimate[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_estimate[1]; + bp->stats.port_ler_cutoff[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_cutoff[0]; + bp->stats.port_ler_cutoff[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_cutoff[1]; + bp->stats.port_ler_alarm[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_alarm[0]; + bp->stats.port_ler_alarm[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_alarm[1]; + bp->stats.port_connect_state[0] = bp->cmd_rsp_virt->smt_mib_get.port_connect_state[0]; + bp->stats.port_connect_state[1] = bp->cmd_rsp_virt->smt_mib_get.port_connect_state[1]; + bp->stats.port_pcm_state[0] = bp->cmd_rsp_virt->smt_mib_get.port_pcm_state[0]; + bp->stats.port_pcm_state[1] = bp->cmd_rsp_virt->smt_mib_get.port_pcm_state[1]; + bp->stats.port_pc_withhold[0] = bp->cmd_rsp_virt->smt_mib_get.port_pc_withhold[0]; + bp->stats.port_pc_withhold[1] = bp->cmd_rsp_virt->smt_mib_get.port_pc_withhold[1]; + bp->stats.port_ler_flag[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_flag[0]; + bp->stats.port_ler_flag[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_flag[1]; + bp->stats.port_hardware_present[0] = bp->cmd_rsp_virt->smt_mib_get.port_hardware_present[0]; + bp->stats.port_hardware_present[1] = bp->cmd_rsp_virt->smt_mib_get.port_hardware_present[1]; + + + /* Fill the bp->stats structure with the FDDI counter values */ + + bp->stats.mac_frame_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.frame_cnt.ls; + bp->stats.mac_copied_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.copied_cnt.ls; + bp->stats.mac_transmit_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.transmit_cnt.ls; + bp->stats.mac_error_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.error_cnt.ls; + bp->stats.mac_lost_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.lost_cnt.ls; + bp->stats.port_lct_fail_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.lct_rejects[0].ls; + bp->stats.port_lct_fail_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.lct_rejects[1].ls; + bp->stats.port_lem_reject_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.lem_rejects[0].ls; + bp->stats.port_lem_reject_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.lem_rejects[1].ls; + bp->stats.port_lem_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.link_errors[0].ls; + bp->stats.port_lem_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.link_errors[1].ls; + +#endif + return (struct net_device_stats *)&bp->os.MacStat; +} // ctl_get_stat + + +/* + * ============================== + * = skfp_ctl_set_multicast_list = + * ============================== + * + * Overview: + * Enable/Disable LLC frame promiscuous mode reception + * on the adapter and/or update multicast address table. + * + * Returns: + * None + * + * Arguments: + * dev - pointer to device information + * + * Functional Description: + * This function acquires the driver lock and only calls + * skfp_ctl_set_multicast_list_wo_lock then. + * This routine follows a fairly simple algorithm for setting the + * adapter filters and CAM: + * + * if IFF_PROMISC flag is set + * enable promiscuous mode + * else + * disable promiscuous mode + * if number of multicast addresses <= max. multicast number + * add mc addresses to adapter table + * else + * enable promiscuous mode + * update adapter filters + * + * Assumptions: + * Multicast addresses are presented in canonical (LSB) format. + * + * Side Effects: + * On-board adapter filters are updated. + */ +static void skfp_ctl_set_multicast_list(struct net_device *dev) +{ + struct s_smc *smc = netdev_priv(dev); + skfddi_priv *bp = &smc->os; + unsigned long Flags; + + spin_lock_irqsave(&bp->DriverLock, Flags); + skfp_ctl_set_multicast_list_wo_lock(dev); + spin_unlock_irqrestore(&bp->DriverLock, Flags); +} // skfp_ctl_set_multicast_list + + + +static void skfp_ctl_set_multicast_list_wo_lock(struct net_device *dev) +{ + struct s_smc *smc = netdev_priv(dev); + struct netdev_hw_addr *ha; + + /* Enable promiscuous mode, if necessary */ + if (dev->flags & IFF_PROMISC) { + mac_drv_rx_mode(smc, RX_ENABLE_PROMISC); + pr_debug("PROMISCUOUS MODE ENABLED\n"); + } + /* Else, update multicast address table */ + else { + mac_drv_rx_mode(smc, RX_DISABLE_PROMISC); + pr_debug("PROMISCUOUS MODE DISABLED\n"); + + // Reset all MC addresses + mac_clear_multicast(smc); + mac_drv_rx_mode(smc, RX_DISABLE_ALLMULTI); + + if (dev->flags & IFF_ALLMULTI) { + mac_drv_rx_mode(smc, RX_ENABLE_ALLMULTI); + pr_debug("ENABLE ALL MC ADDRESSES\n"); + } else if (!netdev_mc_empty(dev)) { + if (netdev_mc_count(dev) <= FPMAX_MULTICAST) { + /* use exact filtering */ + + // point to first multicast addr + netdev_for_each_mc_addr(ha, dev) { + mac_add_multicast(smc, + (struct fddi_addr *)ha->addr, + 1); + + pr_debug("ENABLE MC ADDRESS: %pMF\n", + ha->addr); + } + + } else { // more MC addresses than HW supports + + mac_drv_rx_mode(smc, RX_ENABLE_ALLMULTI); + pr_debug("ENABLE ALL MC ADDRESSES\n"); + } + } else { // no MC addresses + + pr_debug("DISABLE ALL MC ADDRESSES\n"); + } + + /* Update adapter filters */ + mac_update_multicast(smc); + } +} // skfp_ctl_set_multicast_list_wo_lock + + +/* + * =========================== + * = skfp_ctl_set_mac_address = + * =========================== + * + * Overview: + * set new mac address on adapter and update dev_addr field in device table. + * + * Returns: + * None + * + * Arguments: + * dev - pointer to device information + * addr - pointer to sockaddr structure containing unicast address to set + * + * Assumptions: + * The address pointed to by addr->sa_data is a valid unicast + * address and is presented in canonical (LSB) format. + */ +static int skfp_ctl_set_mac_address(struct net_device *dev, void *addr) +{ + struct s_smc *smc = netdev_priv(dev); + struct sockaddr *p_sockaddr = (struct sockaddr *) addr; + skfddi_priv *bp = &smc->os; + unsigned long Flags; + + + memcpy(dev->dev_addr, p_sockaddr->sa_data, FDDI_K_ALEN); + spin_lock_irqsave(&bp->DriverLock, Flags); + ResetAdapter(smc); + spin_unlock_irqrestore(&bp->DriverLock, Flags); + + return 0; /* always return zero */ +} // skfp_ctl_set_mac_address + + +/* + * ============== + * = skfp_ioctl = + * ============== + * + * Overview: + * + * Perform IOCTL call functions here. Some are privileged operations and the + * effective uid is checked in those cases. + * + * Returns: + * status value + * 0 - success + * other - failure + * + * Arguments: + * dev - pointer to device information + * rq - pointer to ioctl request structure + * cmd - ? + * + */ + + +static int skfp_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) +{ + struct s_smc *smc = netdev_priv(dev); + skfddi_priv *lp = &smc->os; + struct s_skfp_ioctl ioc; + int status = 0; + + if (copy_from_user(&ioc, rq->ifr_data, sizeof(struct s_skfp_ioctl))) + return -EFAULT; + + switch (ioc.cmd) { + case SKFP_GET_STATS: /* Get the driver statistics */ + ioc.len = sizeof(lp->MacStat); + status = copy_to_user(ioc.data, skfp_ctl_get_stats(dev), ioc.len) + ? -EFAULT : 0; + break; + case SKFP_CLR_STATS: /* Zero out the driver statistics */ + if (!capable(CAP_NET_ADMIN)) { + status = -EPERM; + } else { + memset(&lp->MacStat, 0, sizeof(lp->MacStat)); + } + break; + default: + printk("ioctl for %s: unknown cmd: %04x\n", dev->name, ioc.cmd); + status = -EOPNOTSUPP; + + } // switch + + return status; +} // skfp_ioctl + + +/* + * ===================== + * = skfp_send_pkt = + * ===================== + * + * Overview: + * Queues a packet for transmission and try to transmit it. + * + * Returns: + * Condition code + * + * Arguments: + * skb - pointer to sk_buff to queue for transmission + * dev - pointer to device information + * + * Functional Description: + * Here we assume that an incoming skb transmit request + * is contained in a single physically contiguous buffer + * in which the virtual address of the start of packet + * (skb->data) can be converted to a physical address + * by using pci_map_single(). + * + * We have an internal queue for packets we can not send + * immediately. Packets in this queue can be given to the + * adapter if transmit buffers are freed. + * + * We can't free the skb until after it's been DMA'd + * out by the adapter, so we'll keep it in the driver and + * return it in mac_drv_tx_complete. + * + * Return Codes: + * 0 - driver has queued and/or sent packet + * 1 - caller should requeue the sk_buff for later transmission + * + * Assumptions: + * The entire packet is stored in one physically + * contiguous buffer which is not cached and whose + * 32-bit physical address can be determined. + * + * It's vital that this routine is NOT reentered for the + * same board and that the OS is not in another section of + * code (eg. skfp_interrupt) for the same board on a + * different thread. + * + * Side Effects: + * None + */ +static netdev_tx_t skfp_send_pkt(struct sk_buff *skb, + struct net_device *dev) +{ + struct s_smc *smc = netdev_priv(dev); + skfddi_priv *bp = &smc->os; + + pr_debug("skfp_send_pkt\n"); + + /* + * Verify that incoming transmit request is OK + * + * Note: The packet size check is consistent with other + * Linux device drivers, although the correct packet + * size should be verified before calling the + * transmit routine. + */ + + if (!(skb->len >= FDDI_K_LLC_ZLEN && skb->len <= FDDI_K_LLC_LEN)) { + bp->MacStat.gen.tx_errors++; /* bump error counter */ + // dequeue packets from xmt queue and send them + netif_start_queue(dev); + dev_kfree_skb(skb); + return NETDEV_TX_OK; /* return "success" */ + } + if (bp->QueueSkb == 0) { // return with tbusy set: queue full + + netif_stop_queue(dev); + return NETDEV_TX_BUSY; + } + bp->QueueSkb--; + skb_queue_tail(&bp->SendSkbQueue, skb); + send_queued_packets(netdev_priv(dev)); + if (bp->QueueSkb == 0) { + netif_stop_queue(dev); + } + return NETDEV_TX_OK; + +} // skfp_send_pkt + + +/* + * ======================= + * = send_queued_packets = + * ======================= + * + * Overview: + * Send packets from the driver queue as long as there are some and + * transmit resources are available. + * + * Returns: + * None + * + * Arguments: + * smc - pointer to smc (adapter) structure + * + * Functional Description: + * Take a packet from queue if there is any. If not, then we are done. + * Check if there are resources to send the packet. If not, requeue it + * and exit. + * Set packet descriptor flags and give packet to adapter. + * Check if any send resources can be freed (we do not use the + * transmit complete interrupt). + */ +static void send_queued_packets(struct s_smc *smc) +{ + skfddi_priv *bp = &smc->os; + struct sk_buff *skb; + unsigned char fc; + int queue; + struct s_smt_fp_txd *txd; // Current TxD. + dma_addr_t dma_address; + unsigned long Flags; + + int frame_status; // HWM tx frame status. + + pr_debug("send queued packets\n"); + for (;;) { + // send first buffer from queue + skb = skb_dequeue(&bp->SendSkbQueue); + + if (!skb) { + pr_debug("queue empty\n"); + return; + } // queue empty ! + + spin_lock_irqsave(&bp->DriverLock, Flags); + fc = skb->data[0]; + queue = (fc & FC_SYNC_BIT) ? QUEUE_S : QUEUE_A0; +#ifdef ESS + // Check if the frame may/must be sent as a synchronous frame. + + if ((fc & ~(FC_SYNC_BIT | FC_LLC_PRIOR)) == FC_ASYNC_LLC) { + // It's an LLC frame. + if (!smc->ess.sync_bw_available) + fc &= ~FC_SYNC_BIT; // No bandwidth available. + + else { // Bandwidth is available. + + if (smc->mib.fddiESSSynchTxMode) { + // Send as sync. frame. + fc |= FC_SYNC_BIT; + } + } + } +#endif // ESS + frame_status = hwm_tx_init(smc, fc, 1, skb->len, queue); + + if ((frame_status & (LOC_TX | LAN_TX)) == 0) { + // Unable to send the frame. + + if ((frame_status & RING_DOWN) != 0) { + // Ring is down. + pr_debug("Tx attempt while ring down.\n"); + } else if ((frame_status & OUT_OF_TXD) != 0) { + pr_debug("%s: out of TXDs.\n", bp->dev->name); + } else { + pr_debug("%s: out of transmit resources", + bp->dev->name); + } + + // Note: We will retry the operation as soon as + // transmit resources become available. + skb_queue_head(&bp->SendSkbQueue, skb); + spin_unlock_irqrestore(&bp->DriverLock, Flags); + return; // Packet has been queued. + + } // if (unable to send frame) + + bp->QueueSkb++; // one packet less in local queue + + // source address in packet ? + CheckSourceAddress(skb->data, smc->hw.fddi_canon_addr.a); + + txd = (struct s_smt_fp_txd *) HWM_GET_CURR_TXD(smc, queue); + + dma_address = pci_map_single(&bp->pdev, skb->data, + skb->len, PCI_DMA_TODEVICE); + if (frame_status & LAN_TX) { + txd->txd_os.skb = skb; // save skb + txd->txd_os.dma_addr = dma_address; // save dma mapping + } + hwm_tx_frag(smc, skb->data, dma_address, skb->len, + frame_status | FIRST_FRAG | LAST_FRAG | EN_IRQ_EOF); + + if (!(frame_status & LAN_TX)) { // local only frame + pci_unmap_single(&bp->pdev, dma_address, + skb->len, PCI_DMA_TODEVICE); + dev_kfree_skb_irq(skb); + } + spin_unlock_irqrestore(&bp->DriverLock, Flags); + } // for + + return; // never reached + +} // send_queued_packets + + +/************************ + * + * CheckSourceAddress + * + * Verify if the source address is set. Insert it if necessary. + * + ************************/ +static void CheckSourceAddress(unsigned char *frame, unsigned char *hw_addr) +{ + unsigned char SRBit; + + if ((((unsigned long) frame[1 + 6]) & ~0x01) != 0) // source routing bit + + return; + if ((unsigned short) frame[1 + 10] != 0) + return; + SRBit = frame[1 + 6] & 0x01; + memcpy(&frame[1 + 6], hw_addr, ETH_ALEN); + frame[8] |= SRBit; +} // CheckSourceAddress + + +/************************ + * + * ResetAdapter + * + * Reset the adapter and bring it back to operational mode. + * Args + * smc - A pointer to the SMT context struct. + * Out + * Nothing. + * + ************************/ +static void ResetAdapter(struct s_smc *smc) +{ + + pr_debug("[fddi: ResetAdapter]\n"); + + // Stop the adapter. + + card_stop(smc); // Stop all activity. + + // Clear the transmit and receive descriptor queues. + mac_drv_clear_tx_queue(smc); + mac_drv_clear_rx_queue(smc); + + // Restart the adapter. + + smt_reset_defaults(smc, 1); // Initialize the SMT module. + + init_smt(smc, (smc->os.dev)->dev_addr); // Initialize the hardware. + + smt_online(smc, 1); // Insert into the ring again. + STI_FBI(); + + // Restore original receive mode (multicasts, promiscuous, etc.). + skfp_ctl_set_multicast_list_wo_lock(smc->os.dev); +} // ResetAdapter + + +//--------------- functions called by hardware module ---------------- + +/************************ + * + * llc_restart_tx + * + * The hardware driver calls this routine when the transmit complete + * interrupt bits (end of frame) for the synchronous or asynchronous + * queue is set. + * + * NOTE The hardware driver calls this function also if no packets are queued. + * The routine must be able to handle this case. + * Args + * smc - A pointer to the SMT context struct. + * Out + * Nothing. + * + ************************/ +void llc_restart_tx(struct s_smc *smc) +{ + skfddi_priv *bp = &smc->os; + + pr_debug("[llc_restart_tx]\n"); + + // Try to send queued packets + spin_unlock(&bp->DriverLock); + send_queued_packets(smc); + spin_lock(&bp->DriverLock); + netif_start_queue(bp->dev);// system may send again if it was blocked + +} // llc_restart_tx + + +/************************ + * + * mac_drv_get_space + * + * The hardware module calls this function to allocate the memory + * for the SMT MBufs if the define MB_OUTSIDE_SMC is specified. + * Args + * smc - A pointer to the SMT context struct. + * + * size - Size of memory in bytes to allocate. + * Out + * != 0 A pointer to the virtual address of the allocated memory. + * == 0 Allocation error. + * + ************************/ +void *mac_drv_get_space(struct s_smc *smc, unsigned int size) +{ + void *virt; + + pr_debug("mac_drv_get_space (%d bytes), ", size); + virt = (void *) (smc->os.SharedMemAddr + smc->os.SharedMemHeap); + + if ((smc->os.SharedMemHeap + size) > smc->os.SharedMemSize) { + printk("Unexpected SMT memory size requested: %d\n", size); + return NULL; + } + smc->os.SharedMemHeap += size; // Move heap pointer. + + pr_debug("mac_drv_get_space end\n"); + pr_debug("virt addr: %lx\n", (ulong) virt); + pr_debug("bus addr: %lx\n", (ulong) + (smc->os.SharedMemDMA + + ((char *) virt - (char *)smc->os.SharedMemAddr))); + return virt; +} // mac_drv_get_space + + +/************************ + * + * mac_drv_get_desc_mem + * + * This function is called by the hardware dependent module. + * It allocates the memory for the RxD and TxD descriptors. + * + * This memory must be non-cached, non-movable and non-swappable. + * This memory should start at a physical page boundary. + * Args + * smc - A pointer to the SMT context struct. + * + * size - Size of memory in bytes to allocate. + * Out + * != 0 A pointer to the virtual address of the allocated memory. + * == 0 Allocation error. + * + ************************/ +void *mac_drv_get_desc_mem(struct s_smc *smc, unsigned int size) +{ + + char *virt; + + pr_debug("mac_drv_get_desc_mem\n"); + + // Descriptor memory must be aligned on 16-byte boundary. + + virt = mac_drv_get_space(smc, size); + + size = (u_int) (16 - (((unsigned long) virt) & 15UL)); + size = size % 16; + + pr_debug("Allocate %u bytes alignment gap ", size); + pr_debug("for descriptor memory.\n"); + + if (!mac_drv_get_space(smc, size)) { + printk("fddi: Unable to align descriptor memory.\n"); + return NULL; + } + return virt + size; +} // mac_drv_get_desc_mem + + +/************************ + * + * mac_drv_virt2phys + * + * Get the physical address of a given virtual address. + * Args + * smc - A pointer to the SMT context struct. + * + * virt - A (virtual) pointer into our 'shared' memory area. + * Out + * Physical address of the given virtual address. + * + ************************/ +unsigned long mac_drv_virt2phys(struct s_smc *smc, void *virt) +{ + return smc->os.SharedMemDMA + + ((char *) virt - (char *)smc->os.SharedMemAddr); +} // mac_drv_virt2phys + + +/************************ + * + * dma_master + * + * The HWM calls this function, when the driver leads through a DMA + * transfer. If the OS-specific module must prepare the system hardware + * for the DMA transfer, it should do it in this function. + * + * The hardware module calls this dma_master if it wants to send an SMT + * frame. This means that the virt address passed in here is part of + * the 'shared' memory area. + * Args + * smc - A pointer to the SMT context struct. + * + * virt - The virtual address of the data. + * + * len - The length in bytes of the data. + * + * flag - Indicates the transmit direction and the buffer type: + * DMA_RD (0x01) system RAM ==> adapter buffer memory + * DMA_WR (0x02) adapter buffer memory ==> system RAM + * SMT_BUF (0x80) SMT buffer + * + * >> NOTE: SMT_BUF and DMA_RD are always set for PCI. << + * Out + * Returns the pyhsical address for the DMA transfer. + * + ************************/ +u_long dma_master(struct s_smc * smc, void *virt, int len, int flag) +{ + return smc->os.SharedMemDMA + + ((char *) virt - (char *)smc->os.SharedMemAddr); +} // dma_master + + +/************************ + * + * dma_complete + * + * The hardware module calls this routine when it has completed a DMA + * transfer. If the operating system dependent module has set up the DMA + * channel via dma_master() (e.g. Windows NT or AIX) it should clean up + * the DMA channel. + * Args + * smc - A pointer to the SMT context struct. + * + * descr - A pointer to a TxD or RxD, respectively. + * + * flag - Indicates the DMA transfer direction / SMT buffer: + * DMA_RD (0x01) system RAM ==> adapter buffer memory + * DMA_WR (0x02) adapter buffer memory ==> system RAM + * SMT_BUF (0x80) SMT buffer (managed by HWM) + * Out + * Nothing. + * + ************************/ +void dma_complete(struct s_smc *smc, volatile union s_fp_descr *descr, int flag) +{ + /* For TX buffers, there are two cases. If it is an SMT transmit + * buffer, there is nothing to do since we use consistent memory + * for the 'shared' memory area. The other case is for normal + * transmit packets given to us by the networking stack, and in + * that case we cleanup the PCI DMA mapping in mac_drv_tx_complete + * below. + * + * For RX buffers, we have to unmap dynamic PCI DMA mappings here + * because the hardware module is about to potentially look at + * the contents of the buffer. If we did not call the PCI DMA + * unmap first, the hardware module could read inconsistent data. + */ + if (flag & DMA_WR) { + skfddi_priv *bp = &smc->os; + volatile struct s_smt_fp_rxd *r = &descr->r; + + /* If SKB is NULL, we used the local buffer. */ + if (r->rxd_os.skb && r->rxd_os.dma_addr) { + int MaxFrameSize = bp->MaxFrameSize; + + pci_unmap_single(&bp->pdev, r->rxd_os.dma_addr, + MaxFrameSize, PCI_DMA_FROMDEVICE); + r->rxd_os.dma_addr = 0; + } + } +} // dma_complete + + +/************************ + * + * mac_drv_tx_complete + * + * Transmit of a packet is complete. Release the tx staging buffer. + * + * Args + * smc - A pointer to the SMT context struct. + * + * txd - A pointer to the last TxD which is used by the frame. + * Out + * Returns nothing. + * + ************************/ +void mac_drv_tx_complete(struct s_smc *smc, volatile struct s_smt_fp_txd *txd) +{ + struct sk_buff *skb; + + pr_debug("entering mac_drv_tx_complete\n"); + // Check if this TxD points to a skb + + if (!(skb = txd->txd_os.skb)) { + pr_debug("TXD with no skb assigned.\n"); + return; + } + txd->txd_os.skb = NULL; + + // release the DMA mapping + pci_unmap_single(&smc->os.pdev, txd->txd_os.dma_addr, + skb->len, PCI_DMA_TODEVICE); + txd->txd_os.dma_addr = 0; + + smc->os.MacStat.gen.tx_packets++; // Count transmitted packets. + smc->os.MacStat.gen.tx_bytes+=skb->len; // Count bytes + + // free the skb + dev_kfree_skb_irq(skb); + + pr_debug("leaving mac_drv_tx_complete\n"); +} // mac_drv_tx_complete + + +/************************ + * + * dump packets to logfile + * + ************************/ +#ifdef DUMPPACKETS +void dump_data(unsigned char *Data, int length) +{ + int i, j; + unsigned char s[255], sh[10]; + if (length > 64) { + length = 64; + } + printk(KERN_INFO "---Packet start---\n"); + for (i = 0, j = 0; i < length / 8; i++, j += 8) + printk(KERN_INFO "%02x %02x %02x %02x %02x %02x %02x %02x\n", + Data[j + 0], Data[j + 1], Data[j + 2], Data[j + 3], + Data[j + 4], Data[j + 5], Data[j + 6], Data[j + 7]); + strcpy(s, ""); + for (i = 0; i < length % 8; i++) { + sprintf(sh, "%02x ", Data[j + i]); + strcat(s, sh); + } + printk(KERN_INFO "%s\n", s); + printk(KERN_INFO "------------------\n"); +} // dump_data +#else +#define dump_data(data,len) +#endif // DUMPPACKETS + +/************************ + * + * mac_drv_rx_complete + * + * The hardware module calls this function if an LLC frame is received + * in a receive buffer. Also the SMT, NSA, and directed beacon frames + * from the network will be passed to the LLC layer by this function + * if passing is enabled. + * + * mac_drv_rx_complete forwards the frame to the LLC layer if it should + * be received. It also fills the RxD ring with new receive buffers if + * some can be queued. + * Args + * smc - A pointer to the SMT context struct. + * + * rxd - A pointer to the first RxD which is used by the receive frame. + * + * frag_count - Count of RxDs used by the received frame. + * + * len - Frame length. + * Out + * Nothing. + * + ************************/ +void mac_drv_rx_complete(struct s_smc *smc, volatile struct s_smt_fp_rxd *rxd, + int frag_count, int len) +{ + skfddi_priv *bp = &smc->os; + struct sk_buff *skb; + unsigned char *virt, *cp; + unsigned short ri; + u_int RifLength; + + pr_debug("entering mac_drv_rx_complete (len=%d)\n", len); + if (frag_count != 1) { // This is not allowed to happen. + + printk("fddi: Multi-fragment receive!\n"); + goto RequeueRxd; // Re-use the given RXD(s). + + } + skb = rxd->rxd_os.skb; + if (!skb) { + pr_debug("No skb in rxd\n"); + smc->os.MacStat.gen.rx_errors++; + goto RequeueRxd; + } + virt = skb->data; + + // The DMA mapping was released in dma_complete above. + + dump_data(skb->data, len); + + /* + * FDDI Frame format: + * +-------+-------+-------+------------+--------+------------+ + * | FC[1] | DA[6] | SA[6] | RIF[0..18] | LLC[3] | Data[0..n] | + * +-------+-------+-------+------------+--------+------------+ + * + * FC = Frame Control + * DA = Destination Address + * SA = Source Address + * RIF = Routing Information Field + * LLC = Logical Link Control + */ + + // Remove Routing Information Field (RIF), if present. + + if ((virt[1 + 6] & FDDI_RII) == 0) + RifLength = 0; + else { + int n; +// goos: RIF removal has still to be tested + pr_debug("RIF found\n"); + // Get RIF length from Routing Control (RC) field. + cp = virt + FDDI_MAC_HDR_LEN; // Point behind MAC header. + + ri = ntohs(*((__be16 *) cp)); + RifLength = ri & FDDI_RCF_LEN_MASK; + if (len < (int) (FDDI_MAC_HDR_LEN + RifLength)) { + printk("fddi: Invalid RIF.\n"); + goto RequeueRxd; // Discard the frame. + + } + virt[1 + 6] &= ~FDDI_RII; // Clear RII bit. + // regions overlap + + virt = cp + RifLength; + for (n = FDDI_MAC_HDR_LEN; n; n--) + *--virt = *--cp; + // adjust sbd->data pointer + skb_pull(skb, RifLength); + len -= RifLength; + RifLength = 0; + } + + // Count statistics. + smc->os.MacStat.gen.rx_packets++; // Count indicated receive + // packets. + smc->os.MacStat.gen.rx_bytes+=len; // Count bytes. + + // virt points to header again + if (virt[1] & 0x01) { // Check group (multicast) bit. + + smc->os.MacStat.gen.multicast++; + } + + // deliver frame to system + rxd->rxd_os.skb = NULL; + skb_trim(skb, len); + skb->protocol = fddi_type_trans(skb, bp->dev); + + netif_rx(skb); + + HWM_RX_CHECK(smc, RX_LOW_WATERMARK); + return; + + RequeueRxd: + pr_debug("Rx: re-queue RXD.\n"); + mac_drv_requeue_rxd(smc, rxd, frag_count); + smc->os.MacStat.gen.rx_errors++; // Count receive packets + // not indicated. + +} // mac_drv_rx_complete + + +/************************ + * + * mac_drv_requeue_rxd + * + * The hardware module calls this function to request the OS-specific + * module to queue the receive buffer(s) represented by the pointer + * to the RxD and the frag_count into the receive queue again. This + * buffer was filled with an invalid frame or an SMT frame. + * Args + * smc - A pointer to the SMT context struct. + * + * rxd - A pointer to the first RxD which is used by the receive frame. + * + * frag_count - Count of RxDs used by the received frame. + * Out + * Nothing. + * + ************************/ +void mac_drv_requeue_rxd(struct s_smc *smc, volatile struct s_smt_fp_rxd *rxd, + int frag_count) +{ + volatile struct s_smt_fp_rxd *next_rxd; + volatile struct s_smt_fp_rxd *src_rxd; + struct sk_buff *skb; + int MaxFrameSize; + unsigned char *v_addr; + dma_addr_t b_addr; + + if (frag_count != 1) // This is not allowed to happen. + + printk("fddi: Multi-fragment requeue!\n"); + + MaxFrameSize = smc->os.MaxFrameSize; + src_rxd = rxd; + for (; frag_count > 0; frag_count--) { + next_rxd = src_rxd->rxd_next; + rxd = HWM_GET_CURR_RXD(smc); + + skb = src_rxd->rxd_os.skb; + if (skb == NULL) { // this should not happen + + pr_debug("Requeue with no skb in rxd!\n"); + skb = alloc_skb(MaxFrameSize + 3, GFP_ATOMIC); + if (skb) { + // we got a skb + rxd->rxd_os.skb = skb; + skb_reserve(skb, 3); + skb_put(skb, MaxFrameSize); + v_addr = skb->data; + b_addr = pci_map_single(&smc->os.pdev, + v_addr, + MaxFrameSize, + PCI_DMA_FROMDEVICE); + rxd->rxd_os.dma_addr = b_addr; + } else { + // no skb available, use local buffer + pr_debug("Queueing invalid buffer!\n"); + rxd->rxd_os.skb = NULL; + v_addr = smc->os.LocalRxBuffer; + b_addr = smc->os.LocalRxBufferDMA; + } + } else { + // we use skb from old rxd + rxd->rxd_os.skb = skb; + v_addr = skb->data; + b_addr = pci_map_single(&smc->os.pdev, + v_addr, + MaxFrameSize, + PCI_DMA_FROMDEVICE); + rxd->rxd_os.dma_addr = b_addr; + } + hwm_rx_frag(smc, v_addr, b_addr, MaxFrameSize, + FIRST_FRAG | LAST_FRAG); + + src_rxd = next_rxd; + } +} // mac_drv_requeue_rxd + + +/************************ + * + * mac_drv_fill_rxd + * + * The hardware module calls this function at initialization time + * to fill the RxD ring with receive buffers. It is also called by + * mac_drv_rx_complete if rx_free is large enough to queue some new + * receive buffers into the RxD ring. mac_drv_fill_rxd queues new + * receive buffers as long as enough RxDs and receive buffers are + * available. + * Args + * smc - A pointer to the SMT context struct. + * Out + * Nothing. + * + ************************/ +void mac_drv_fill_rxd(struct s_smc *smc) +{ + int MaxFrameSize; + unsigned char *v_addr; + unsigned long b_addr; + struct sk_buff *skb; + volatile struct s_smt_fp_rxd *rxd; + + pr_debug("entering mac_drv_fill_rxd\n"); + + // Walk through the list of free receive buffers, passing receive + // buffers to the HWM as long as RXDs are available. + + MaxFrameSize = smc->os.MaxFrameSize; + // Check if there is any RXD left. + while (HWM_GET_RX_FREE(smc) > 0) { + pr_debug(".\n"); + + rxd = HWM_GET_CURR_RXD(smc); + skb = alloc_skb(MaxFrameSize + 3, GFP_ATOMIC); + if (skb) { + // we got a skb + skb_reserve(skb, 3); + skb_put(skb, MaxFrameSize); + v_addr = skb->data; + b_addr = pci_map_single(&smc->os.pdev, + v_addr, + MaxFrameSize, + PCI_DMA_FROMDEVICE); + rxd->rxd_os.dma_addr = b_addr; + } else { + // no skb available, use local buffer + // System has run out of buffer memory, but we want to + // keep the receiver running in hope of better times. + // Multiple descriptors may point to this local buffer, + // so data in it must be considered invalid. + pr_debug("Queueing invalid buffer!\n"); + v_addr = smc->os.LocalRxBuffer; + b_addr = smc->os.LocalRxBufferDMA; + } + + rxd->rxd_os.skb = skb; + + // Pass receive buffer to HWM. + hwm_rx_frag(smc, v_addr, b_addr, MaxFrameSize, + FIRST_FRAG | LAST_FRAG); + } + pr_debug("leaving mac_drv_fill_rxd\n"); +} // mac_drv_fill_rxd + + +/************************ + * + * mac_drv_clear_rxd + * + * The hardware module calls this function to release unused + * receive buffers. + * Args + * smc - A pointer to the SMT context struct. + * + * rxd - A pointer to the first RxD which is used by the receive buffer. + * + * frag_count - Count of RxDs used by the receive buffer. + * Out + * Nothing. + * + ************************/ +void mac_drv_clear_rxd(struct s_smc *smc, volatile struct s_smt_fp_rxd *rxd, + int frag_count) +{ + + struct sk_buff *skb; + + pr_debug("entering mac_drv_clear_rxd\n"); + + if (frag_count != 1) // This is not allowed to happen. + + printk("fddi: Multi-fragment clear!\n"); + + for (; frag_count > 0; frag_count--) { + skb = rxd->rxd_os.skb; + if (skb != NULL) { + skfddi_priv *bp = &smc->os; + int MaxFrameSize = bp->MaxFrameSize; + + pci_unmap_single(&bp->pdev, rxd->rxd_os.dma_addr, + MaxFrameSize, PCI_DMA_FROMDEVICE); + + dev_kfree_skb(skb); + rxd->rxd_os.skb = NULL; + } + rxd = rxd->rxd_next; // Next RXD. + + } +} // mac_drv_clear_rxd + + +/************************ + * + * mac_drv_rx_init + * + * The hardware module calls this routine when an SMT or NSA frame of the + * local SMT should be delivered to the LLC layer. + * + * It is necessary to have this function, because there is no other way to + * copy the contents of SMT MBufs into receive buffers. + * + * mac_drv_rx_init allocates the required target memory for this frame, + * and receives the frame fragment by fragment by calling mac_drv_rx_frag. + * Args + * smc - A pointer to the SMT context struct. + * + * len - The length (in bytes) of the received frame (FC, DA, SA, Data). + * + * fc - The Frame Control field of the received frame. + * + * look_ahead - A pointer to the lookahead data buffer (may be NULL). + * + * la_len - The length of the lookahead data stored in the lookahead + * buffer (may be zero). + * Out + * Always returns zero (0). + * + ************************/ +int mac_drv_rx_init(struct s_smc *smc, int len, int fc, + char *look_ahead, int la_len) +{ + struct sk_buff *skb; + + pr_debug("entering mac_drv_rx_init(len=%d)\n", len); + + // "Received" a SMT or NSA frame of the local SMT. + + if (len != la_len || len < FDDI_MAC_HDR_LEN || !look_ahead) { + pr_debug("fddi: Discard invalid local SMT frame\n"); + pr_debug(" len=%d, la_len=%d, (ULONG) look_ahead=%08lXh.\n", + len, la_len, (unsigned long) look_ahead); + return 0; + } + skb = alloc_skb(len + 3, GFP_ATOMIC); + if (!skb) { + pr_debug("fddi: Local SMT: skb memory exhausted.\n"); + return 0; + } + skb_reserve(skb, 3); + skb_put(skb, len); + skb_copy_to_linear_data(skb, look_ahead, len); + + // deliver frame to system + skb->protocol = fddi_type_trans(skb, smc->os.dev); + netif_rx(skb); + + return 0; +} // mac_drv_rx_init + + +/************************ + * + * smt_timer_poll + * + * This routine is called periodically by the SMT module to clean up the + * driver. + * + * Return any queued frames back to the upper protocol layers if the ring + * is down. + * Args + * smc - A pointer to the SMT context struct. + * Out + * Nothing. + * + ************************/ +void smt_timer_poll(struct s_smc *smc) +{ +} // smt_timer_poll + + +/************************ + * + * ring_status_indication + * + * This function indicates a change of the ring state. + * Args + * smc - A pointer to the SMT context struct. + * + * status - The current ring status. + * Out + * Nothing. + * + ************************/ +void ring_status_indication(struct s_smc *smc, u_long status) +{ + pr_debug("ring_status_indication( "); + if (status & RS_RES15) + pr_debug("RS_RES15 "); + if (status & RS_HARDERROR) + pr_debug("RS_HARDERROR "); + if (status & RS_SOFTERROR) + pr_debug("RS_SOFTERROR "); + if (status & RS_BEACON) + pr_debug("RS_BEACON "); + if (status & RS_PATHTEST) + pr_debug("RS_PATHTEST "); + if (status & RS_SELFTEST) + pr_debug("RS_SELFTEST "); + if (status & RS_RES9) + pr_debug("RS_RES9 "); + if (status & RS_DISCONNECT) + pr_debug("RS_DISCONNECT "); + if (status & RS_RES7) + pr_debug("RS_RES7 "); + if (status & RS_DUPADDR) + pr_debug("RS_DUPADDR "); + if (status & RS_NORINGOP) + pr_debug("RS_NORINGOP "); + if (status & RS_VERSION) + pr_debug("RS_VERSION "); + if (status & RS_STUCKBYPASSS) + pr_debug("RS_STUCKBYPASSS "); + if (status & RS_EVENT) + pr_debug("RS_EVENT "); + if (status & RS_RINGOPCHANGE) + pr_debug("RS_RINGOPCHANGE "); + if (status & RS_RES0) + pr_debug("RS_RES0 "); + pr_debug("]\n"); +} // ring_status_indication + + +/************************ + * + * smt_get_time + * + * Gets the current time from the system. + * Args + * None. + * Out + * The current time in TICKS_PER_SECOND. + * + * TICKS_PER_SECOND has the unit 'count of timer ticks per second'. It is + * defined in "targetos.h". The definition of TICKS_PER_SECOND must comply + * to the time returned by smt_get_time(). + * + ************************/ +unsigned long smt_get_time(void) +{ + return jiffies; +} // smt_get_time + + +/************************ + * + * smt_stat_counter + * + * Status counter update (ring_op, fifo full). + * Args + * smc - A pointer to the SMT context struct. + * + * stat - = 0: A ring operational change occurred. + * = 1: The FORMAC FIFO buffer is full / FIFO overflow. + * Out + * Nothing. + * + ************************/ +void smt_stat_counter(struct s_smc *smc, int stat) +{ +// BOOLEAN RingIsUp ; + + pr_debug("smt_stat_counter\n"); + switch (stat) { + case 0: + pr_debug("Ring operational change.\n"); + break; + case 1: + pr_debug("Receive fifo overflow.\n"); + smc->os.MacStat.gen.rx_errors++; + break; + default: + pr_debug("Unknown status (%d).\n", stat); + break; + } +} // smt_stat_counter + + +/************************ + * + * cfm_state_change + * + * Sets CFM state in custom statistics. + * Args + * smc - A pointer to the SMT context struct. + * + * c_state - Possible values are: + * + * EC0_OUT, EC1_IN, EC2_TRACE, EC3_LEAVE, EC4_PATH_TEST, + * EC5_INSERT, EC6_CHECK, EC7_DEINSERT + * Out + * Nothing. + * + ************************/ +void cfm_state_change(struct s_smc *smc, int c_state) +{ +#ifdef DRIVERDEBUG + char *s; + + switch (c_state) { + case SC0_ISOLATED: + s = "SC0_ISOLATED"; + break; + case SC1_WRAP_A: + s = "SC1_WRAP_A"; + break; + case SC2_WRAP_B: + s = "SC2_WRAP_B"; + break; + case SC4_THRU_A: + s = "SC4_THRU_A"; + break; + case SC5_THRU_B: + s = "SC5_THRU_B"; + break; + case SC7_WRAP_S: + s = "SC7_WRAP_S"; + break; + case SC9_C_WRAP_A: + s = "SC9_C_WRAP_A"; + break; + case SC10_C_WRAP_B: + s = "SC10_C_WRAP_B"; + break; + case SC11_C_WRAP_S: + s = "SC11_C_WRAP_S"; + break; + default: + pr_debug("cfm_state_change: unknown %d\n", c_state); + return; + } + pr_debug("cfm_state_change: %s\n", s); +#endif // DRIVERDEBUG +} // cfm_state_change + + +/************************ + * + * ecm_state_change + * + * Sets ECM state in custom statistics. + * Args + * smc - A pointer to the SMT context struct. + * + * e_state - Possible values are: + * + * SC0_ISOLATED, SC1_WRAP_A (5), SC2_WRAP_B (6), SC4_THRU_A (12), + * SC5_THRU_B (7), SC7_WRAP_S (8) + * Out + * Nothing. + * + ************************/ +void ecm_state_change(struct s_smc *smc, int e_state) +{ +#ifdef DRIVERDEBUG + char *s; + + switch (e_state) { + case EC0_OUT: + s = "EC0_OUT"; + break; + case EC1_IN: + s = "EC1_IN"; + break; + case EC2_TRACE: + s = "EC2_TRACE"; + break; + case EC3_LEAVE: + s = "EC3_LEAVE"; + break; + case EC4_PATH_TEST: + s = "EC4_PATH_TEST"; + break; + case EC5_INSERT: + s = "EC5_INSERT"; + break; + case EC6_CHECK: + s = "EC6_CHECK"; + break; + case EC7_DEINSERT: + s = "EC7_DEINSERT"; + break; + default: + s = "unknown"; + break; + } + pr_debug("ecm_state_change: %s\n", s); +#endif //DRIVERDEBUG +} // ecm_state_change + + +/************************ + * + * rmt_state_change + * + * Sets RMT state in custom statistics. + * Args + * smc - A pointer to the SMT context struct. + * + * r_state - Possible values are: + * + * RM0_ISOLATED, RM1_NON_OP, RM2_RING_OP, RM3_DETECT, + * RM4_NON_OP_DUP, RM5_RING_OP_DUP, RM6_DIRECTED, RM7_TRACE + * Out + * Nothing. + * + ************************/ +void rmt_state_change(struct s_smc *smc, int r_state) +{ +#ifdef DRIVERDEBUG + char *s; + + switch (r_state) { + case RM0_ISOLATED: + s = "RM0_ISOLATED"; + break; + case RM1_NON_OP: + s = "RM1_NON_OP - not operational"; + break; + case RM2_RING_OP: + s = "RM2_RING_OP - ring operational"; + break; + case RM3_DETECT: + s = "RM3_DETECT - detect dupl addresses"; + break; + case RM4_NON_OP_DUP: + s = "RM4_NON_OP_DUP - dupl. addr detected"; + break; + case RM5_RING_OP_DUP: + s = "RM5_RING_OP_DUP - ring oper. with dupl. addr"; + break; + case RM6_DIRECTED: + s = "RM6_DIRECTED - sending directed beacons"; + break; + case RM7_TRACE: + s = "RM7_TRACE - trace initiated"; + break; + default: + s = "unknown"; + break; + } + pr_debug("[rmt_state_change: %s]\n", s); +#endif // DRIVERDEBUG +} // rmt_state_change + + +/************************ + * + * drv_reset_indication + * + * This function is called by the SMT when it has detected a severe + * hardware problem. The driver should perform a reset on the adapter + * as soon as possible, but not from within this function. + * Args + * smc - A pointer to the SMT context struct. + * Out + * Nothing. + * + ************************/ +void drv_reset_indication(struct s_smc *smc) +{ + pr_debug("entering drv_reset_indication\n"); + + smc->os.ResetRequested = TRUE; // Set flag. + +} // drv_reset_indication + +static struct pci_driver skfddi_pci_driver = { + .name = "skfddi", + .id_table = skfddi_pci_tbl, + .probe = skfp_init_one, + .remove = skfp_remove_one, +}; + +module_pci_driver(skfddi_pci_driver); diff --git a/kernel/drivers/net/fddi/skfp/smt.c b/kernel/drivers/net/fddi/skfp/smt.c new file mode 100644 index 000000000..cd78b7cac --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/smt.c @@ -0,0 +1,2034 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/smt_p.h" +#include <linux/bitrev.h> +#include <linux/kernel.h> + +#define KERNEL +#include "h/smtstate.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)smt.c 2.43 98/11/23 (C) SK " ; +#endif + +/* + * FC in SMbuf + */ +#define m_fc(mb) ((mb)->sm_data[0]) + +#define SMT_TID_MAGIC 0x1f0a7b3c + +#ifdef DEBUG +static const char *const smt_type_name[] = { + "SMT_00??", "SMT_INFO", "SMT_02??", "SMT_03??", + "SMT_04??", "SMT_05??", "SMT_06??", "SMT_07??", + "SMT_08??", "SMT_09??", "SMT_0A??", "SMT_0B??", + "SMT_0C??", "SMT_0D??", "SMT_0E??", "SMT_NSA" +} ; + +static const char *const smt_class_name[] = { + "UNKNOWN","NIF","SIF_CONFIG","SIF_OPER","ECF","RAF","RDF", + "SRF","PMF_GET","PMF_SET","ESF" +} ; +#endif +#define LAST_CLASS (SMT_PMF_SET) + +static const struct fddi_addr SMT_Unknown = { + { 0,0,0x1f,0,0,0 } +} ; + +/* + * function prototypes + */ +#ifdef LITTLE_ENDIAN +static int smt_swap_short(u_short s); +#endif +static int mac_index(struct s_smc *smc, int mac); +static int phy_index(struct s_smc *smc, int phy); +static int mac_con_resource_index(struct s_smc *smc, int mac); +static int phy_con_resource_index(struct s_smc *smc, int phy); +static void smt_send_rdf(struct s_smc *smc, SMbuf *rej, int fc, int reason, + int local); +static void smt_send_nif(struct s_smc *smc, const struct fddi_addr *dest, + int fc, u_long tid, int type, int local); +static void smt_send_ecf(struct s_smc *smc, struct fddi_addr *dest, int fc, + u_long tid, int type, int len); +static void smt_echo_test(struct s_smc *smc, int dna); +static void smt_send_sif_config(struct s_smc *smc, struct fddi_addr *dest, + u_long tid, int local); +static void smt_send_sif_operation(struct s_smc *smc, struct fddi_addr *dest, + u_long tid, int local); +#ifdef LITTLE_ENDIAN +static void smt_string_swap(char *data, const char *format, int len); +#endif +static void smt_add_frame_len(SMbuf *mb, int len); +static void smt_fill_una(struct s_smc *smc, struct smt_p_una *una); +static void smt_fill_sde(struct s_smc *smc, struct smt_p_sde *sde); +static void smt_fill_state(struct s_smc *smc, struct smt_p_state *state); +static void smt_fill_timestamp(struct s_smc *smc, struct smt_p_timestamp *ts); +static void smt_fill_policy(struct s_smc *smc, struct smt_p_policy *policy); +static void smt_fill_latency(struct s_smc *smc, struct smt_p_latency *latency); +static void smt_fill_neighbor(struct s_smc *smc, struct smt_p_neighbor *neighbor); +static int smt_fill_path(struct s_smc *smc, struct smt_p_path *path); +static void smt_fill_mac_status(struct s_smc *smc, struct smt_p_mac_status *st); +static void smt_fill_lem(struct s_smc *smc, struct smt_p_lem *lem, int phy); +static void smt_fill_version(struct s_smc *smc, struct smt_p_version *vers); +static void smt_fill_fsc(struct s_smc *smc, struct smt_p_fsc *fsc); +static void smt_fill_mac_counter(struct s_smc *smc, struct smt_p_mac_counter *mc); +static void smt_fill_mac_fnc(struct s_smc *smc, struct smt_p_mac_fnc *fnc); +static void smt_fill_manufacturer(struct s_smc *smc, + struct smp_p_manufacturer *man); +static void smt_fill_user(struct s_smc *smc, struct smp_p_user *user); +static void smt_fill_setcount(struct s_smc *smc, struct smt_p_setcount *setcount); +static void smt_fill_echo(struct s_smc *smc, struct smt_p_echo *echo, u_long seed, + int len); + +static void smt_clear_una_dna(struct s_smc *smc); +static void smt_clear_old_una_dna(struct s_smc *smc); +#ifdef CONCENTRATOR +static int entity_to_index(void); +#endif +static void update_dac(struct s_smc *smc, int report); +static int div_ratio(u_long upper, u_long lower); +#ifdef USE_CAN_ADDR +static void hwm_conv_can(struct s_smc *smc, char *data, int len); +#else +#define hwm_conv_can(smc,data,len) +#endif + + +static inline int is_my_addr(const struct s_smc *smc, + const struct fddi_addr *addr) +{ + return(*(short *)(&addr->a[0]) == + *(short *)(&smc->mib.m[MAC0].fddiMACSMTAddress.a[0]) + && *(short *)(&addr->a[2]) == + *(short *)(&smc->mib.m[MAC0].fddiMACSMTAddress.a[2]) + && *(short *)(&addr->a[4]) == + *(short *)(&smc->mib.m[MAC0].fddiMACSMTAddress.a[4])) ; +} + +static inline int is_broadcast(const struct fddi_addr *addr) +{ + return *(u_short *)(&addr->a[0]) == 0xffff && + *(u_short *)(&addr->a[2]) == 0xffff && + *(u_short *)(&addr->a[4]) == 0xffff; +} + +static inline int is_individual(const struct fddi_addr *addr) +{ + return !(addr->a[0] & GROUP_ADDR); +} + +static inline int is_equal(const struct fddi_addr *addr1, + const struct fddi_addr *addr2) +{ + return *(u_short *)(&addr1->a[0]) == *(u_short *)(&addr2->a[0]) && + *(u_short *)(&addr1->a[2]) == *(u_short *)(&addr2->a[2]) && + *(u_short *)(&addr1->a[4]) == *(u_short *)(&addr2->a[4]); +} + +/* + * list of mandatory paras in frames + */ +static const u_short plist_nif[] = { SMT_P_UNA,SMT_P_SDE,SMT_P_STATE,0 } ; + +/* + * init SMT agent + */ +void smt_agent_init(struct s_smc *smc) +{ + int i ; + + /* + * get MAC address + */ + smc->mib.m[MAC0].fddiMACSMTAddress = smc->hw.fddi_home_addr ; + + /* + * get OUI address from driver (bia == built-in-address) + */ + smc->mib.fddiSMTStationId.sid_oem[0] = 0 ; + smc->mib.fddiSMTStationId.sid_oem[1] = 0 ; + driver_get_bia(smc,&smc->mib.fddiSMTStationId.sid_node) ; + for (i = 0 ; i < 6 ; i ++) { + smc->mib.fddiSMTStationId.sid_node.a[i] = + bitrev8(smc->mib.fddiSMTStationId.sid_node.a[i]); + } + smc->mib.fddiSMTManufacturerData[0] = + smc->mib.fddiSMTStationId.sid_node.a[0] ; + smc->mib.fddiSMTManufacturerData[1] = + smc->mib.fddiSMTStationId.sid_node.a[1] ; + smc->mib.fddiSMTManufacturerData[2] = + smc->mib.fddiSMTStationId.sid_node.a[2] ; + smc->sm.smt_tid = 0 ; + smc->mib.m[MAC0].fddiMACDupAddressTest = DA_NONE ; + smc->mib.m[MAC0].fddiMACUNDA_Flag = FALSE ; +#ifndef SLIM_SMT + smt_clear_una_dna(smc) ; + smt_clear_old_una_dna(smc) ; +#endif + for (i = 0 ; i < SMT_MAX_TEST ; i++) + smc->sm.pend[i] = 0 ; + smc->sm.please_reconnect = 0 ; + smc->sm.uniq_ticks = 0 ; +} + +/* + * SMT task + * forever + * delay 30 seconds + * send NIF + * check tvu & tvd + * end + */ +void smt_agent_task(struct s_smc *smc) +{ + smt_timer_start(smc,&smc->sm.smt_timer, (u_long)1000000L, + EV_TOKEN(EVENT_SMT,SM_TIMER)) ; + DB_SMT("SMT agent task\n",0,0) ; +} + +#ifndef SMT_REAL_TOKEN_CT +void smt_emulate_token_ct(struct s_smc *smc, int mac_index) +{ + u_long count; + u_long time; + + + time = smt_get_time(); + count = ((time - smc->sm.last_tok_time[mac_index]) * + 100)/TICKS_PER_SECOND; + + /* + * Only when ring is up we will have a token count. The + * flag is unfortunately a single instance value. This + * doesn't matter now, because we currently have only + * one MAC instance. + */ + if (smc->hw.mac_ring_is_up){ + smc->mib.m[mac_index].fddiMACToken_Ct += count; + } + + /* Remember current time */ + smc->sm.last_tok_time[mac_index] = time; + +} +#endif + +/*ARGSUSED1*/ +void smt_event(struct s_smc *smc, int event) +{ + u_long time ; +#ifndef SMT_REAL_TOKEN_CT + int i ; +#endif + + + if (smc->sm.please_reconnect) { + smc->sm.please_reconnect -- ; + if (smc->sm.please_reconnect == 0) { + /* Counted down */ + queue_event(smc,EVENT_ECM,EC_CONNECT) ; + } + } + + if (event == SM_FAST) + return ; + + /* + * timer for periodic cleanup in driver + * reset and start the watchdog (FM2) + * ESS timer + * SBA timer + */ + smt_timer_poll(smc) ; + smt_start_watchdog(smc) ; +#ifndef SLIM_SMT +#ifndef BOOT +#ifdef ESS + ess_timer_poll(smc) ; +#endif +#endif +#ifdef SBA + sba_timer_poll(smc) ; +#endif + + smt_srf_event(smc,0,0,0) ; + +#endif /* no SLIM_SMT */ + + time = smt_get_time() ; + + if (time - smc->sm.smt_last_lem >= TICKS_PER_SECOND*8) { + /* + * Use 8 sec. for the time intervall, it simplifies the + * LER estimation. + */ + struct fddi_mib_m *mib ; + u_long upper ; + u_long lower ; + int cond ; + int port; + struct s_phy *phy ; + /* + * calculate LEM bit error rate + */ + sm_lem_evaluate(smc) ; + smc->sm.smt_last_lem = time ; + + /* + * check conditions + */ +#ifndef SLIM_SMT + mac_update_counter(smc) ; + mib = smc->mib.m ; + upper = + (mib->fddiMACLost_Ct - mib->fddiMACOld_Lost_Ct) + + (mib->fddiMACError_Ct - mib->fddiMACOld_Error_Ct) ; + lower = + (mib->fddiMACFrame_Ct - mib->fddiMACOld_Frame_Ct) + + (mib->fddiMACLost_Ct - mib->fddiMACOld_Lost_Ct) ; + mib->fddiMACFrameErrorRatio = div_ratio(upper,lower) ; + + cond = + ((!mib->fddiMACFrameErrorThreshold && + mib->fddiMACError_Ct != mib->fddiMACOld_Error_Ct) || + (mib->fddiMACFrameErrorRatio > + mib->fddiMACFrameErrorThreshold)) ; + + if (cond != mib->fddiMACFrameErrorFlag) + smt_srf_event(smc,SMT_COND_MAC_FRAME_ERROR, + INDEX_MAC,cond) ; + + upper = + (mib->fddiMACNotCopied_Ct - mib->fddiMACOld_NotCopied_Ct) ; + lower = + upper + + (mib->fddiMACCopied_Ct - mib->fddiMACOld_Copied_Ct) ; + mib->fddiMACNotCopiedRatio = div_ratio(upper,lower) ; + + cond = + ((!mib->fddiMACNotCopiedThreshold && + mib->fddiMACNotCopied_Ct != + mib->fddiMACOld_NotCopied_Ct)|| + (mib->fddiMACNotCopiedRatio > + mib->fddiMACNotCopiedThreshold)) ; + + if (cond != mib->fddiMACNotCopiedFlag) + smt_srf_event(smc,SMT_COND_MAC_NOT_COPIED, + INDEX_MAC,cond) ; + + /* + * set old values + */ + mib->fddiMACOld_Frame_Ct = mib->fddiMACFrame_Ct ; + mib->fddiMACOld_Copied_Ct = mib->fddiMACCopied_Ct ; + mib->fddiMACOld_Error_Ct = mib->fddiMACError_Ct ; + mib->fddiMACOld_Lost_Ct = mib->fddiMACLost_Ct ; + mib->fddiMACOld_NotCopied_Ct = mib->fddiMACNotCopied_Ct ; + + /* + * Check port EBError Condition + */ + for (port = 0; port < NUMPHYS; port ++) { + phy = &smc->y[port] ; + + if (!phy->mib->fddiPORTHardwarePresent) { + continue; + } + + cond = (phy->mib->fddiPORTEBError_Ct - + phy->mib->fddiPORTOldEBError_Ct > 5) ; + + /* If ratio is more than 5 in 8 seconds + * Set the condition. + */ + smt_srf_event(smc,SMT_COND_PORT_EB_ERROR, + (int) (INDEX_PORT+ phy->np) ,cond) ; + + /* + * set old values + */ + phy->mib->fddiPORTOldEBError_Ct = + phy->mib->fddiPORTEBError_Ct ; + } + +#endif /* no SLIM_SMT */ + } + +#ifndef SLIM_SMT + + if (time - smc->sm.smt_last_notify >= (u_long) + (smc->mib.fddiSMTTT_Notify * TICKS_PER_SECOND) ) { + /* + * we can either send an announcement or a request + * a request will trigger a reply so that we can update + * our dna + * note: same tid must be used until reply is received + */ + if (!smc->sm.pend[SMT_TID_NIF]) + smc->sm.pend[SMT_TID_NIF] = smt_get_tid(smc) ; + smt_send_nif(smc,&fddi_broadcast, FC_SMT_NSA, + smc->sm.pend[SMT_TID_NIF], SMT_REQUEST,0) ; + smc->sm.smt_last_notify = time ; + } + + /* + * check timer + */ + if (smc->sm.smt_tvu && + time - smc->sm.smt_tvu > 228*TICKS_PER_SECOND) { + DB_SMT("SMT : UNA expired\n",0,0) ; + smc->sm.smt_tvu = 0 ; + + if (!is_equal(&smc->mib.m[MAC0].fddiMACUpstreamNbr, + &SMT_Unknown)){ + /* Do not update unknown address */ + smc->mib.m[MAC0].fddiMACOldUpstreamNbr= + smc->mib.m[MAC0].fddiMACUpstreamNbr ; + } + smc->mib.m[MAC0].fddiMACUpstreamNbr = SMT_Unknown ; + smc->mib.m[MAC0].fddiMACUNDA_Flag = FALSE ; + /* + * Make sure the fddiMACUNDA_Flag = FALSE is + * included in the SRF so we don't generate + * a separate SRF for the deassertion of this + * condition + */ + update_dac(smc,0) ; + smt_srf_event(smc, SMT_EVENT_MAC_NEIGHBOR_CHANGE, + INDEX_MAC,0) ; + } + if (smc->sm.smt_tvd && + time - smc->sm.smt_tvd > 228*TICKS_PER_SECOND) { + DB_SMT("SMT : DNA expired\n",0,0) ; + smc->sm.smt_tvd = 0 ; + if (!is_equal(&smc->mib.m[MAC0].fddiMACDownstreamNbr, + &SMT_Unknown)){ + /* Do not update unknown address */ + smc->mib.m[MAC0].fddiMACOldDownstreamNbr= + smc->mib.m[MAC0].fddiMACDownstreamNbr ; + } + smc->mib.m[MAC0].fddiMACDownstreamNbr = SMT_Unknown ; + smt_srf_event(smc, SMT_EVENT_MAC_NEIGHBOR_CHANGE, + INDEX_MAC,0) ; + } + +#endif /* no SLIM_SMT */ + +#ifndef SMT_REAL_TOKEN_CT + /* + * Token counter emulation section. If hardware supports the token + * count, the token counter will be updated in mac_update_counter. + */ + for (i = MAC0; i < NUMMACS; i++ ){ + if (time - smc->sm.last_tok_time[i] > 2*TICKS_PER_SECOND ){ + smt_emulate_token_ct( smc, i ); + } + } +#endif + + smt_timer_start(smc,&smc->sm.smt_timer, (u_long)1000000L, + EV_TOKEN(EVENT_SMT,SM_TIMER)) ; +} + +static int div_ratio(u_long upper, u_long lower) +{ + if ((upper<<16L) < upper) + upper = 0xffff0000L ; + else + upper <<= 16L ; + if (!lower) + return 0; + return (int)(upper/lower) ; +} + +#ifndef SLIM_SMT + +/* + * receive packet handler + */ +void smt_received_pack(struct s_smc *smc, SMbuf *mb, int fs) +/* int fs; frame status */ +{ + struct smt_header *sm ; + int local ; + + int illegal = 0 ; + + switch (m_fc(mb)) { + case FC_SMT_INFO : + case FC_SMT_LAN_LOC : + case FC_SMT_LOC : + case FC_SMT_NSA : + break ; + default : + smt_free_mbuf(smc,mb) ; + return ; + } + + smc->mib.m[MAC0].fddiMACSMTCopied_Ct++ ; + sm = smtod(mb,struct smt_header *) ; + local = ((fs & L_INDICATOR) != 0) ; + hwm_conv_can(smc,(char *)sm,12) ; + + /* check destination address */ + if (is_individual(&sm->smt_dest) && !is_my_addr(smc,&sm->smt_dest)) { + smt_free_mbuf(smc,mb) ; + return ; + } +#if 0 /* for DUP recognition, do NOT filter them */ + /* ignore loop back packets */ + if (is_my_addr(smc,&sm->smt_source) && !local) { + smt_free_mbuf(smc,mb) ; + return ; + } +#endif + + smt_swap_para(sm,(int) mb->sm_len,1) ; + DB_SMT("SMT : received packet [%s] at 0x%x\n", + smt_type_name[m_fc(mb) & 0xf],sm) ; + DB_SMT("SMT : version %d, class %s\n",sm->smt_version, + smt_class_name[(sm->smt_class>LAST_CLASS)?0 : sm->smt_class]) ; + +#ifdef SBA + /* + * check if NSA frame + */ + if (m_fc(mb) == FC_SMT_NSA && sm->smt_class == SMT_NIF && + (sm->smt_type == SMT_ANNOUNCE || sm->smt_type == SMT_REQUEST)) { + smc->sba.sm = sm ; + sba(smc,NIF) ; + } +#endif + + /* + * ignore any packet with NSA and A-indicator set + */ + if ( (fs & A_INDICATOR) && m_fc(mb) == FC_SMT_NSA) { + DB_SMT("SMT : ignoring NSA with A-indicator set from %s\n", + addr_to_string(&sm->smt_source),0) ; + smt_free_mbuf(smc,mb) ; + return ; + } + + /* + * ignore frames with illegal length + */ + if (((sm->smt_class == SMT_ECF) && (sm->smt_len > SMT_MAX_ECHO_LEN)) || + ((sm->smt_class != SMT_ECF) && (sm->smt_len > SMT_MAX_INFO_LEN))) { + smt_free_mbuf(smc,mb) ; + return ; + } + + /* + * check SMT version + */ + switch (sm->smt_class) { + case SMT_NIF : + case SMT_SIF_CONFIG : + case SMT_SIF_OPER : + case SMT_ECF : + if (sm->smt_version != SMT_VID) + illegal = 1; + break ; + default : + if (sm->smt_version != SMT_VID_2) + illegal = 1; + break ; + } + if (illegal) { + DB_SMT("SMT : version = %d, dest = %s\n", + sm->smt_version,addr_to_string(&sm->smt_source)) ; + smt_send_rdf(smc,mb,m_fc(mb),SMT_RDF_VERSION,local) ; + smt_free_mbuf(smc,mb) ; + return ; + } + if ((sm->smt_len > mb->sm_len - sizeof(struct smt_header)) || + ((sm->smt_len & 3) && (sm->smt_class != SMT_ECF))) { + DB_SMT("SMT: info length error, len = %d\n",sm->smt_len,0) ; + smt_send_rdf(smc,mb,m_fc(mb),SMT_RDF_LENGTH,local) ; + smt_free_mbuf(smc,mb) ; + return ; + } + switch (sm->smt_class) { + case SMT_NIF : + if (smt_check_para(smc,sm,plist_nif)) { + DB_SMT("SMT: NIF with para problem, ignoring\n",0,0) ; + break ; + } + switch (sm->smt_type) { + case SMT_ANNOUNCE : + case SMT_REQUEST : + if (!(fs & C_INDICATOR) && m_fc(mb) == FC_SMT_NSA + && is_broadcast(&sm->smt_dest)) { + struct smt_p_state *st ; + + /* set my UNA */ + if (!is_equal( + &smc->mib.m[MAC0].fddiMACUpstreamNbr, + &sm->smt_source)) { + DB_SMT("SMT : updated my UNA = %s\n", + addr_to_string(&sm->smt_source),0) ; + if (!is_equal(&smc->mib.m[MAC0]. + fddiMACUpstreamNbr,&SMT_Unknown)){ + /* Do not update unknown address */ + smc->mib.m[MAC0].fddiMACOldUpstreamNbr= + smc->mib.m[MAC0].fddiMACUpstreamNbr ; + } + + smc->mib.m[MAC0].fddiMACUpstreamNbr = + sm->smt_source ; + smt_srf_event(smc, + SMT_EVENT_MAC_NEIGHBOR_CHANGE, + INDEX_MAC,0) ; + smt_echo_test(smc,0) ; + } + smc->sm.smt_tvu = smt_get_time() ; + st = (struct smt_p_state *) + sm_to_para(smc,sm,SMT_P_STATE) ; + if (st) { + smc->mib.m[MAC0].fddiMACUNDA_Flag = + (st->st_dupl_addr & SMT_ST_MY_DUPA) ? + TRUE : FALSE ; + update_dac(smc,1) ; + } + } + if ((sm->smt_type == SMT_REQUEST) && + is_individual(&sm->smt_source) && + ((!(fs & A_INDICATOR) && m_fc(mb) == FC_SMT_NSA) || + (m_fc(mb) != FC_SMT_NSA))) { + DB_SMT("SMT : replying to NIF request %s\n", + addr_to_string(&sm->smt_source),0) ; + smt_send_nif(smc,&sm->smt_source, + FC_SMT_INFO, + sm->smt_tid, + SMT_REPLY,local) ; + } + break ; + case SMT_REPLY : + DB_SMT("SMT : received NIF response from %s\n", + addr_to_string(&sm->smt_source),0) ; + if (fs & A_INDICATOR) { + smc->sm.pend[SMT_TID_NIF] = 0 ; + DB_SMT("SMT : duplicate address\n",0,0) ; + smc->mib.m[MAC0].fddiMACDupAddressTest = + DA_FAILED ; + smc->r.dup_addr_test = DA_FAILED ; + queue_event(smc,EVENT_RMT,RM_DUP_ADDR) ; + smc->mib.m[MAC0].fddiMACDA_Flag = TRUE ; + update_dac(smc,1) ; + break ; + } + if (sm->smt_tid == smc->sm.pend[SMT_TID_NIF]) { + smc->sm.pend[SMT_TID_NIF] = 0 ; + /* set my DNA */ + if (!is_equal( + &smc->mib.m[MAC0].fddiMACDownstreamNbr, + &sm->smt_source)) { + DB_SMT("SMT : updated my DNA\n",0,0) ; + if (!is_equal(&smc->mib.m[MAC0]. + fddiMACDownstreamNbr, &SMT_Unknown)){ + /* Do not update unknown address */ + smc->mib.m[MAC0].fddiMACOldDownstreamNbr = + smc->mib.m[MAC0].fddiMACDownstreamNbr ; + } + + smc->mib.m[MAC0].fddiMACDownstreamNbr = + sm->smt_source ; + smt_srf_event(smc, + SMT_EVENT_MAC_NEIGHBOR_CHANGE, + INDEX_MAC,0) ; + smt_echo_test(smc,1) ; + } + smc->mib.m[MAC0].fddiMACDA_Flag = FALSE ; + update_dac(smc,1) ; + smc->sm.smt_tvd = smt_get_time() ; + smc->mib.m[MAC0].fddiMACDupAddressTest = + DA_PASSED ; + if (smc->r.dup_addr_test != DA_PASSED) { + smc->r.dup_addr_test = DA_PASSED ; + queue_event(smc,EVENT_RMT,RM_DUP_ADDR) ; + } + } + else if (sm->smt_tid == + smc->sm.pend[SMT_TID_NIF_TEST]) { + DB_SMT("SMT : NIF test TID ok\n",0,0) ; + } + else { + DB_SMT("SMT : expected TID %lx, got %lx\n", + smc->sm.pend[SMT_TID_NIF],sm->smt_tid) ; + } + break ; + default : + illegal = 2 ; + break ; + } + break ; + case SMT_SIF_CONFIG : /* station information */ + if (sm->smt_type != SMT_REQUEST) + break ; + DB_SMT("SMT : replying to SIF Config request from %s\n", + addr_to_string(&sm->smt_source),0) ; + smt_send_sif_config(smc,&sm->smt_source,sm->smt_tid,local) ; + break ; + case SMT_SIF_OPER : /* station information */ + if (sm->smt_type != SMT_REQUEST) + break ; + DB_SMT("SMT : replying to SIF Operation request from %s\n", + addr_to_string(&sm->smt_source),0) ; + smt_send_sif_operation(smc,&sm->smt_source,sm->smt_tid,local) ; + break ; + case SMT_ECF : /* echo frame */ + switch (sm->smt_type) { + case SMT_REPLY : + smc->mib.priv.fddiPRIVECF_Reply_Rx++ ; + DB_SMT("SMT: received ECF reply from %s\n", + addr_to_string(&sm->smt_source),0) ; + if (sm_to_para(smc,sm,SMT_P_ECHODATA) == NULL) { + DB_SMT("SMT: ECHODATA missing\n",0,0) ; + break ; + } + if (sm->smt_tid == smc->sm.pend[SMT_TID_ECF]) { + DB_SMT("SMT : ECF test TID ok\n",0,0) ; + } + else if (sm->smt_tid == smc->sm.pend[SMT_TID_ECF_UNA]) { + DB_SMT("SMT : ECF test UNA ok\n",0,0) ; + } + else if (sm->smt_tid == smc->sm.pend[SMT_TID_ECF_DNA]) { + DB_SMT("SMT : ECF test DNA ok\n",0,0) ; + } + else { + DB_SMT("SMT : expected TID %lx, got %lx\n", + smc->sm.pend[SMT_TID_ECF], + sm->smt_tid) ; + } + break ; + case SMT_REQUEST : + smc->mib.priv.fddiPRIVECF_Req_Rx++ ; + { + if (sm->smt_len && !sm_to_para(smc,sm,SMT_P_ECHODATA)) { + DB_SMT("SMT: ECF with para problem,sending RDF\n",0,0) ; + smt_send_rdf(smc,mb,m_fc(mb),SMT_RDF_LENGTH, + local) ; + break ; + } + DB_SMT("SMT - sending ECF reply to %s\n", + addr_to_string(&sm->smt_source),0) ; + + /* set destination addr. & reply */ + sm->smt_dest = sm->smt_source ; + sm->smt_type = SMT_REPLY ; + dump_smt(smc,sm,"ECF REPLY") ; + smc->mib.priv.fddiPRIVECF_Reply_Tx++ ; + smt_send_frame(smc,mb,FC_SMT_INFO,local) ; + return ; /* DON'T free mbuf */ + } + default : + illegal = 1 ; + break ; + } + break ; +#ifndef BOOT + case SMT_RAF : /* resource allocation */ +#ifdef ESS + DB_ESSN(2,"ESS: RAF frame received\n",0,0) ; + fs = ess_raf_received_pack(smc,mb,sm,fs) ; +#endif + +#ifdef SBA + DB_SBAN(2,"SBA: RAF frame received\n",0,0) ; + sba_raf_received_pack(smc,sm,fs) ; +#endif + break ; + case SMT_RDF : /* request denied */ + smc->mib.priv.fddiPRIVRDF_Rx++ ; + break ; + case SMT_ESF : /* extended service - not supported */ + if (sm->smt_type == SMT_REQUEST) { + DB_SMT("SMT - received ESF, sending RDF\n",0,0) ; + smt_send_rdf(smc,mb,m_fc(mb),SMT_RDF_CLASS,local) ; + } + break ; + case SMT_PMF_GET : + case SMT_PMF_SET : + if (sm->smt_type != SMT_REQUEST) + break ; + /* update statistics */ + if (sm->smt_class == SMT_PMF_GET) + smc->mib.priv.fddiPRIVPMF_Get_Rx++ ; + else + smc->mib.priv.fddiPRIVPMF_Set_Rx++ ; + /* + * ignore PMF SET with I/G set + */ + if ((sm->smt_class == SMT_PMF_SET) && + !is_individual(&sm->smt_dest)) { + DB_SMT("SMT: ignoring PMF-SET with I/G set\n",0,0) ; + break ; + } + smt_pmf_received_pack(smc,mb, local) ; + break ; + case SMT_SRF : + dump_smt(smc,sm,"SRF received") ; + break ; + default : + if (sm->smt_type != SMT_REQUEST) + break ; + /* + * For frames with unknown class: + * we need to send a RDF frame according to 8.1.3.1.1, + * only if it is a REQUEST. + */ + DB_SMT("SMT : class = %d, send RDF to %s\n", + sm->smt_class, addr_to_string(&sm->smt_source)) ; + + smt_send_rdf(smc,mb,m_fc(mb),SMT_RDF_CLASS,local) ; + break ; +#endif + } + if (illegal) { + DB_SMT("SMT: discarding invalid frame, reason = %d\n", + illegal,0) ; + } + smt_free_mbuf(smc,mb) ; +} + +static void update_dac(struct s_smc *smc, int report) +{ + int cond ; + + cond = ( smc->mib.m[MAC0].fddiMACUNDA_Flag | + smc->mib.m[MAC0].fddiMACDA_Flag) != 0 ; + if (report && (cond != smc->mib.m[MAC0].fddiMACDuplicateAddressCond)) + smt_srf_event(smc, SMT_COND_MAC_DUP_ADDR,INDEX_MAC,cond) ; + else + smc->mib.m[MAC0].fddiMACDuplicateAddressCond = cond ; +} + +/* + * send SMT frame + * set source address + * set station ID + * send frame + */ +void smt_send_frame(struct s_smc *smc, SMbuf *mb, int fc, int local) +/* SMbuf *mb; buffer to send */ +/* int fc; FC value */ +{ + struct smt_header *sm ; + + if (!smc->r.sm_ma_avail && !local) { + smt_free_mbuf(smc,mb) ; + return ; + } + sm = smtod(mb,struct smt_header *) ; + sm->smt_source = smc->mib.m[MAC0].fddiMACSMTAddress ; + sm->smt_sid = smc->mib.fddiSMTStationId ; + + smt_swap_para(sm,(int) mb->sm_len,0) ; /* swap para & header */ + hwm_conv_can(smc,(char *)sm,12) ; /* convert SA and DA */ + smc->mib.m[MAC0].fddiMACSMTTransmit_Ct++ ; + smt_send_mbuf(smc,mb,local ? FC_SMT_LOC : fc) ; +} + +/* + * generate and send RDF + */ +static void smt_send_rdf(struct s_smc *smc, SMbuf *rej, int fc, int reason, + int local) +/* SMbuf *rej; mbuf of offending frame */ +/* int fc; FC of denied frame */ +/* int reason; reason code */ +{ + SMbuf *mb ; + struct smt_header *sm ; /* header of offending frame */ + struct smt_rdf *rdf ; + int len ; + int frame_len ; + + sm = smtod(rej,struct smt_header *) ; + if (sm->smt_type != SMT_REQUEST) + return ; + + DB_SMT("SMT: sending RDF to %s,reason = 0x%x\n", + addr_to_string(&sm->smt_source),reason) ; + + + /* + * note: get framelength from MAC length, NOT from SMT header + * smt header length is included in sm_len + */ + frame_len = rej->sm_len ; + + if (!(mb=smt_build_frame(smc,SMT_RDF,SMT_REPLY,sizeof(struct smt_rdf)))) + return ; + rdf = smtod(mb,struct smt_rdf *) ; + rdf->smt.smt_tid = sm->smt_tid ; /* use TID from sm */ + rdf->smt.smt_dest = sm->smt_source ; /* set dest = source */ + + /* set P12 */ + rdf->reason.para.p_type = SMT_P_REASON ; + rdf->reason.para.p_len = sizeof(struct smt_p_reason) - PARA_LEN ; + rdf->reason.rdf_reason = reason ; + + /* set P14 */ + rdf->version.para.p_type = SMT_P_VERSION ; + rdf->version.para.p_len = sizeof(struct smt_p_version) - PARA_LEN ; + rdf->version.v_pad = 0 ; + rdf->version.v_n = 1 ; + rdf->version.v_index = 1 ; + rdf->version.v_version[0] = SMT_VID_2 ; + rdf->version.v_pad2 = 0 ; + + /* set P13 */ + if ((unsigned int) frame_len <= SMT_MAX_INFO_LEN - sizeof(*rdf) + + 2*sizeof(struct smt_header)) + len = frame_len ; + else + len = SMT_MAX_INFO_LEN - sizeof(*rdf) + + 2*sizeof(struct smt_header) ; + /* make length multiple of 4 */ + len &= ~3 ; + rdf->refused.para.p_type = SMT_P_REFUSED ; + /* length of para is smt_frame + ref_fc */ + rdf->refused.para.p_len = len + 4 ; + rdf->refused.ref_fc = fc ; + + /* swap it back */ + smt_swap_para(sm,frame_len,0) ; + + memcpy((char *) &rdf->refused.ref_header,(char *) sm,len) ; + + len -= sizeof(struct smt_header) ; + mb->sm_len += len ; + rdf->smt.smt_len += len ; + + dump_smt(smc,(struct smt_header *)rdf,"RDF") ; + smc->mib.priv.fddiPRIVRDF_Tx++ ; + smt_send_frame(smc,mb,FC_SMT_INFO,local) ; +} + +/* + * generate and send NIF + */ +static void smt_send_nif(struct s_smc *smc, const struct fddi_addr *dest, + int fc, u_long tid, int type, int local) +/* struct fddi_addr *dest; dest address */ +/* int fc; frame control */ +/* u_long tid; transaction id */ +/* int type; frame type */ +{ + struct smt_nif *nif ; + SMbuf *mb ; + + if (!(mb = smt_build_frame(smc,SMT_NIF,type,sizeof(struct smt_nif)))) + return ; + nif = smtod(mb, struct smt_nif *) ; + smt_fill_una(smc,&nif->una) ; /* set UNA */ + smt_fill_sde(smc,&nif->sde) ; /* set station descriptor */ + smt_fill_state(smc,&nif->state) ; /* set state information */ +#ifdef SMT6_10 + smt_fill_fsc(smc,&nif->fsc) ; /* set frame status cap. */ +#endif + nif->smt.smt_dest = *dest ; /* destination address */ + nif->smt.smt_tid = tid ; /* transaction ID */ + dump_smt(smc,(struct smt_header *)nif,"NIF") ; + smt_send_frame(smc,mb,fc,local) ; +} + +#ifdef DEBUG +/* + * send NIF request (test purpose) + */ +static void smt_send_nif_request(struct s_smc *smc, struct fddi_addr *dest) +{ + smc->sm.pend[SMT_TID_NIF_TEST] = smt_get_tid(smc) ; + smt_send_nif(smc,dest, FC_SMT_INFO, smc->sm.pend[SMT_TID_NIF_TEST], + SMT_REQUEST,0) ; +} + +/* + * send ECF request (test purpose) + */ +static void smt_send_ecf_request(struct s_smc *smc, struct fddi_addr *dest, + int len) +{ + smc->sm.pend[SMT_TID_ECF] = smt_get_tid(smc) ; + smt_send_ecf(smc,dest, FC_SMT_INFO, smc->sm.pend[SMT_TID_ECF], + SMT_REQUEST,len) ; +} +#endif + +/* + * echo test + */ +static void smt_echo_test(struct s_smc *smc, int dna) +{ + u_long tid ; + + smc->sm.pend[dna ? SMT_TID_ECF_DNA : SMT_TID_ECF_UNA] = + tid = smt_get_tid(smc) ; + smt_send_ecf(smc, dna ? + &smc->mib.m[MAC0].fddiMACDownstreamNbr : + &smc->mib.m[MAC0].fddiMACUpstreamNbr, + FC_SMT_INFO,tid, SMT_REQUEST, (SMT_TEST_ECHO_LEN & ~3)-8) ; +} + +/* + * generate and send ECF + */ +static void smt_send_ecf(struct s_smc *smc, struct fddi_addr *dest, int fc, + u_long tid, int type, int len) +/* struct fddi_addr *dest; dest address */ +/* int fc; frame control */ +/* u_long tid; transaction id */ +/* int type; frame type */ +/* int len; frame length */ +{ + struct smt_ecf *ecf ; + SMbuf *mb ; + + if (!(mb = smt_build_frame(smc,SMT_ECF,type,SMT_ECF_LEN + len))) + return ; + ecf = smtod(mb, struct smt_ecf *) ; + + smt_fill_echo(smc,&ecf->ec_echo,tid,len) ; /* set ECHO */ + ecf->smt.smt_dest = *dest ; /* destination address */ + ecf->smt.smt_tid = tid ; /* transaction ID */ + smc->mib.priv.fddiPRIVECF_Req_Tx++ ; + smt_send_frame(smc,mb,fc,0) ; +} + +/* + * generate and send SIF config response + */ + +static void smt_send_sif_config(struct s_smc *smc, struct fddi_addr *dest, + u_long tid, int local) +/* struct fddi_addr *dest; dest address */ +/* u_long tid; transaction id */ +{ + struct smt_sif_config *sif ; + SMbuf *mb ; + int len ; + if (!(mb = smt_build_frame(smc,SMT_SIF_CONFIG,SMT_REPLY, + SIZEOF_SMT_SIF_CONFIG))) + return ; + + sif = smtod(mb, struct smt_sif_config *) ; + smt_fill_timestamp(smc,&sif->ts) ; /* set time stamp */ + smt_fill_sde(smc,&sif->sde) ; /* set station descriptor */ + smt_fill_version(smc,&sif->version) ; /* set version information */ + smt_fill_state(smc,&sif->state) ; /* set state information */ + smt_fill_policy(smc,&sif->policy) ; /* set station policy */ + smt_fill_latency(smc,&sif->latency); /* set station latency */ + smt_fill_neighbor(smc,&sif->neighbor); /* set station neighbor */ + smt_fill_setcount(smc,&sif->setcount) ; /* set count */ + len = smt_fill_path(smc,&sif->path); /* set station path descriptor*/ + sif->smt.smt_dest = *dest ; /* destination address */ + sif->smt.smt_tid = tid ; /* transaction ID */ + smt_add_frame_len(mb,len) ; /* adjust length fields */ + dump_smt(smc,(struct smt_header *)sif,"SIF Configuration Reply") ; + smt_send_frame(smc,mb,FC_SMT_INFO,local) ; +} + +/* + * generate and send SIF operation response + */ + +static void smt_send_sif_operation(struct s_smc *smc, struct fddi_addr *dest, + u_long tid, int local) +/* struct fddi_addr *dest; dest address */ +/* u_long tid; transaction id */ +{ + struct smt_sif_operation *sif ; + SMbuf *mb ; + int ports ; + int i ; + + ports = NUMPHYS ; +#ifndef CONCENTRATOR + if (smc->s.sas == SMT_SAS) + ports = 1 ; +#endif + + if (!(mb = smt_build_frame(smc,SMT_SIF_OPER,SMT_REPLY, + SIZEOF_SMT_SIF_OPERATION+ports*sizeof(struct smt_p_lem)))) + return ; + sif = smtod(mb, struct smt_sif_operation *) ; + smt_fill_timestamp(smc,&sif->ts) ; /* set time stamp */ + smt_fill_mac_status(smc,&sif->status) ; /* set mac status */ + smt_fill_mac_counter(smc,&sif->mc) ; /* set mac counter field */ + smt_fill_mac_fnc(smc,&sif->fnc) ; /* set frame not copied counter */ + smt_fill_manufacturer(smc,&sif->man) ; /* set manufacturer field */ + smt_fill_user(smc,&sif->user) ; /* set user field */ + smt_fill_setcount(smc,&sif->setcount) ; /* set count */ + /* + * set link error mon information + */ + if (ports == 1) { + smt_fill_lem(smc,sif->lem,PS) ; + } + else { + for (i = 0 ; i < ports ; i++) { + smt_fill_lem(smc,&sif->lem[i],i) ; + } + } + + sif->smt.smt_dest = *dest ; /* destination address */ + sif->smt.smt_tid = tid ; /* transaction ID */ + dump_smt(smc,(struct smt_header *)sif,"SIF Operation Reply") ; + smt_send_frame(smc,mb,FC_SMT_INFO,local) ; +} + +/* + * get and initialize SMT frame + */ +SMbuf *smt_build_frame(struct s_smc *smc, int class, int type, + int length) +{ + SMbuf *mb ; + struct smt_header *smt ; + +#if 0 + if (!smc->r.sm_ma_avail) { + return 0; + } +#endif + if (!(mb = smt_get_mbuf(smc))) + return mb; + + mb->sm_len = length ; + smt = smtod(mb, struct smt_header *) ; + smt->smt_dest = fddi_broadcast ; /* set dest = broadcast */ + smt->smt_class = class ; + smt->smt_type = type ; + switch (class) { + case SMT_NIF : + case SMT_SIF_CONFIG : + case SMT_SIF_OPER : + case SMT_ECF : + smt->smt_version = SMT_VID ; + break ; + default : + smt->smt_version = SMT_VID_2 ; + break ; + } + smt->smt_tid = smt_get_tid(smc) ; /* set transaction ID */ + smt->smt_pad = 0 ; + smt->smt_len = length - sizeof(struct smt_header) ; + return mb; +} + +static void smt_add_frame_len(SMbuf *mb, int len) +{ + struct smt_header *smt ; + + smt = smtod(mb, struct smt_header *) ; + smt->smt_len += len ; + mb->sm_len += len ; +} + + + +/* + * fill values in UNA parameter + */ +static void smt_fill_una(struct s_smc *smc, struct smt_p_una *una) +{ + SMTSETPARA(una,SMT_P_UNA) ; + una->una_pad = 0 ; + una->una_node = smc->mib.m[MAC0].fddiMACUpstreamNbr ; +} + +/* + * fill values in SDE parameter + */ +static void smt_fill_sde(struct s_smc *smc, struct smt_p_sde *sde) +{ + SMTSETPARA(sde,SMT_P_SDE) ; + sde->sde_non_master = smc->mib.fddiSMTNonMaster_Ct ; + sde->sde_master = smc->mib.fddiSMTMaster_Ct ; + sde->sde_mac_count = NUMMACS ; /* only 1 MAC */ +#ifdef CONCENTRATOR + sde->sde_type = SMT_SDE_CONCENTRATOR ; +#else + sde->sde_type = SMT_SDE_STATION ; +#endif +} + +/* + * fill in values in station state parameter + */ +static void smt_fill_state(struct s_smc *smc, struct smt_p_state *state) +{ + int top ; + int twist ; + + SMTSETPARA(state,SMT_P_STATE) ; + state->st_pad = 0 ; + + /* determine topology */ + top = 0 ; + if (smc->mib.fddiSMTPeerWrapFlag) { + top |= SMT_ST_WRAPPED ; /* state wrapped */ + } +#ifdef CONCENTRATOR + if (cfm_status_unattached(smc)) { + top |= SMT_ST_UNATTACHED ; /* unattached concentrator */ + } +#endif + if ((twist = pcm_status_twisted(smc)) & 1) { + top |= SMT_ST_TWISTED_A ; /* twisted cable */ + } + if (twist & 2) { + top |= SMT_ST_TWISTED_B ; /* twisted cable */ + } +#ifdef OPT_SRF + top |= SMT_ST_SRF ; +#endif + if (pcm_rooted_station(smc)) + top |= SMT_ST_ROOTED_S ; + if (smc->mib.a[0].fddiPATHSbaPayload != 0) + top |= SMT_ST_SYNC_SERVICE ; + state->st_topology = top ; + state->st_dupl_addr = + ((smc->mib.m[MAC0].fddiMACDA_Flag ? SMT_ST_MY_DUPA : 0 ) | + (smc->mib.m[MAC0].fddiMACUNDA_Flag ? SMT_ST_UNA_DUPA : 0)) ; +} + +/* + * fill values in timestamp parameter + */ +static void smt_fill_timestamp(struct s_smc *smc, struct smt_p_timestamp *ts) +{ + + SMTSETPARA(ts,SMT_P_TIMESTAMP) ; + smt_set_timestamp(smc,ts->ts_time) ; +} + +void smt_set_timestamp(struct s_smc *smc, u_char *p) +{ + u_long time ; + u_long utime ; + + /* + * timestamp is 64 bits long ; resolution is 80 nS + * our clock resolution is 10mS + * 10mS/80ns = 125000 ~ 2^17 = 131072 + */ + utime = smt_get_time() ; + time = utime * 100 ; + time /= TICKS_PER_SECOND ; + p[0] = 0 ; + p[1] = (u_char)((time>>(8+8+8+8-1)) & 1) ; + p[2] = (u_char)(time>>(8+8+8-1)) ; + p[3] = (u_char)(time>>(8+8-1)) ; + p[4] = (u_char)(time>>(8-1)) ; + p[5] = (u_char)(time<<1) ; + p[6] = (u_char)(smc->sm.uniq_ticks>>8) ; + p[7] = (u_char)smc->sm.uniq_ticks ; + /* + * make sure we don't wrap: restart whenever the upper digits change + */ + if (utime != smc->sm.uniq_time) { + smc->sm.uniq_ticks = 0 ; + } + smc->sm.uniq_ticks++ ; + smc->sm.uniq_time = utime ; +} + +/* + * fill values in station policy parameter + */ +static void smt_fill_policy(struct s_smc *smc, struct smt_p_policy *policy) +{ + int i ; + const u_char *map ; + u_short in ; + u_short out ; + + /* + * MIB para 101b (fddiSMTConnectionPolicy) coding + * is different from 0005 coding + */ + static const u_char ansi_weirdness[16] = { + 0,7,5,3,8,1,6,4,9,10,2,11,12,13,14,15 + } ; + SMTSETPARA(policy,SMT_P_POLICY) ; + + out = 0 ; + in = smc->mib.fddiSMTConnectionPolicy ; + for (i = 0, map = ansi_weirdness ; i < 16 ; i++) { + if (in & 1) + out |= (1<<*map) ; + in >>= 1 ; + map++ ; + } + policy->pl_config = smc->mib.fddiSMTConfigPolicy ; + policy->pl_connect = out ; +} + +/* + * fill values in latency equivalent parameter + */ +static void smt_fill_latency(struct s_smc *smc, struct smt_p_latency *latency) +{ + SMTSETPARA(latency,SMT_P_LATENCY) ; + + latency->lt_phyout_idx1 = phy_index(smc,0) ; + latency->lt_latency1 = 10 ; /* in octets (byte clock) */ + /* + * note: latency has two phy entries by definition + * for a SAS, the 2nd one is null + */ + if (smc->s.sas == SMT_DAS) { + latency->lt_phyout_idx2 = phy_index(smc,1) ; + latency->lt_latency2 = 10 ; /* in octets (byte clock) */ + } + else { + latency->lt_phyout_idx2 = 0 ; + latency->lt_latency2 = 0 ; + } +} + +/* + * fill values in MAC neighbors parameter + */ +static void smt_fill_neighbor(struct s_smc *smc, struct smt_p_neighbor *neighbor) +{ + SMTSETPARA(neighbor,SMT_P_NEIGHBORS) ; + + neighbor->nb_mib_index = INDEX_MAC ; + neighbor->nb_mac_index = mac_index(smc,1) ; + neighbor->nb_una = smc->mib.m[MAC0].fddiMACUpstreamNbr ; + neighbor->nb_dna = smc->mib.m[MAC0].fddiMACDownstreamNbr ; +} + +/* + * fill values in path descriptor + */ +#ifdef CONCENTRATOR +#define ALLPHYS NUMPHYS +#else +#define ALLPHYS ((smc->s.sas == SMT_SAS) ? 1 : 2) +#endif + +static int smt_fill_path(struct s_smc *smc, struct smt_p_path *path) +{ + SK_LOC_DECL(int,type) ; + SK_LOC_DECL(int,state) ; + SK_LOC_DECL(int,remote) ; + SK_LOC_DECL(int,mac) ; + int len ; + int p ; + int physp ; + struct smt_phy_rec *phy ; + struct smt_mac_rec *pd_mac ; + + len = PARA_LEN + + sizeof(struct smt_mac_rec) * NUMMACS + + sizeof(struct smt_phy_rec) * ALLPHYS ; + path->para.p_type = SMT_P_PATH ; + path->para.p_len = len - PARA_LEN ; + + /* PHYs */ + for (p = 0,phy = path->pd_phy ; p < ALLPHYS ; p++, phy++) { + physp = p ; +#ifndef CONCENTRATOR + if (smc->s.sas == SMT_SAS) + physp = PS ; +#endif + pcm_status_state(smc,physp,&type,&state,&remote,&mac) ; +#ifdef LITTLE_ENDIAN + phy->phy_mib_index = smt_swap_short((u_short)p+INDEX_PORT) ; +#else + phy->phy_mib_index = p+INDEX_PORT ; +#endif + phy->phy_type = type ; + phy->phy_connect_state = state ; + phy->phy_remote_type = remote ; + phy->phy_remote_mac = mac ; + phy->phy_resource_idx = phy_con_resource_index(smc,p) ; + } + + /* MAC */ + pd_mac = (struct smt_mac_rec *) phy ; + pd_mac->mac_addr = smc->mib.m[MAC0].fddiMACSMTAddress ; + pd_mac->mac_resource_idx = mac_con_resource_index(smc,1) ; + return len; +} + +/* + * fill values in mac status + */ +static void smt_fill_mac_status(struct s_smc *smc, struct smt_p_mac_status *st) +{ + SMTSETPARA(st,SMT_P_MAC_STATUS) ; + + st->st_mib_index = INDEX_MAC ; + st->st_mac_index = mac_index(smc,1) ; + + mac_update_counter(smc) ; + /* + * timer values are represented in SMT as 2's complement numbers + * units : internal : 2's complement BCLK + */ + st->st_t_req = smc->mib.m[MAC0].fddiMACT_Req ; + st->st_t_neg = smc->mib.m[MAC0].fddiMACT_Neg ; + st->st_t_max = smc->mib.m[MAC0].fddiMACT_Max ; + st->st_tvx_value = smc->mib.m[MAC0].fddiMACTvxValue ; + st->st_t_min = smc->mib.m[MAC0].fddiMACT_Min ; + + st->st_sba = smc->mib.a[PATH0].fddiPATHSbaPayload ; + st->st_frame_ct = smc->mib.m[MAC0].fddiMACFrame_Ct ; + st->st_error_ct = smc->mib.m[MAC0].fddiMACError_Ct ; + st->st_lost_ct = smc->mib.m[MAC0].fddiMACLost_Ct ; +} + +/* + * fill values in LEM status + */ +static void smt_fill_lem(struct s_smc *smc, struct smt_p_lem *lem, int phy) +{ + struct fddi_mib_p *mib ; + + mib = smc->y[phy].mib ; + + SMTSETPARA(lem,SMT_P_LEM) ; + lem->lem_mib_index = phy+INDEX_PORT ; + lem->lem_phy_index = phy_index(smc,phy) ; + lem->lem_pad2 = 0 ; + lem->lem_cutoff = mib->fddiPORTLer_Cutoff ; + lem->lem_alarm = mib->fddiPORTLer_Alarm ; + /* long term bit error rate */ + lem->lem_estimate = mib->fddiPORTLer_Estimate ; + /* # of rejected connections */ + lem->lem_reject_ct = mib->fddiPORTLem_Reject_Ct ; + lem->lem_ct = mib->fddiPORTLem_Ct ; /* total number of errors */ +} + +/* + * fill version parameter + */ +static void smt_fill_version(struct s_smc *smc, struct smt_p_version *vers) +{ + SK_UNUSED(smc) ; + SMTSETPARA(vers,SMT_P_VERSION) ; + vers->v_pad = 0 ; + vers->v_n = 1 ; /* one version is enough .. */ + vers->v_index = 1 ; + vers->v_version[0] = SMT_VID_2 ; + vers->v_pad2 = 0 ; +} + +#ifdef SMT6_10 +/* + * fill frame status capabilities + */ +/* + * note: this para 200B is NOT in swap table, because it's also set in + * PMF add_para + */ +static void smt_fill_fsc(struct s_smc *smc, struct smt_p_fsc *fsc) +{ + SK_UNUSED(smc) ; + SMTSETPARA(fsc,SMT_P_FSC) ; + fsc->fsc_pad0 = 0 ; + fsc->fsc_mac_index = INDEX_MAC ; /* this is MIB ; MIB is NOT + * mac_index ()i ! + */ + fsc->fsc_pad1 = 0 ; + fsc->fsc_value = FSC_TYPE0 ; /* "normal" node */ +#ifdef LITTLE_ENDIAN + fsc->fsc_mac_index = smt_swap_short(INDEX_MAC) ; + fsc->fsc_value = smt_swap_short(FSC_TYPE0) ; +#endif +} +#endif + +/* + * fill mac counter field + */ +static void smt_fill_mac_counter(struct s_smc *smc, struct smt_p_mac_counter *mc) +{ + SMTSETPARA(mc,SMT_P_MAC_COUNTER) ; + mc->mc_mib_index = INDEX_MAC ; + mc->mc_index = mac_index(smc,1) ; + mc->mc_receive_ct = smc->mib.m[MAC0].fddiMACCopied_Ct ; + mc->mc_transmit_ct = smc->mib.m[MAC0].fddiMACTransmit_Ct ; +} + +/* + * fill mac frame not copied counter + */ +static void smt_fill_mac_fnc(struct s_smc *smc, struct smt_p_mac_fnc *fnc) +{ + SMTSETPARA(fnc,SMT_P_MAC_FNC) ; + fnc->nc_mib_index = INDEX_MAC ; + fnc->nc_index = mac_index(smc,1) ; + fnc->nc_counter = smc->mib.m[MAC0].fddiMACNotCopied_Ct ; +} + + +/* + * fill manufacturer field + */ +static void smt_fill_manufacturer(struct s_smc *smc, + struct smp_p_manufacturer *man) +{ + SMTSETPARA(man,SMT_P_MANUFACTURER) ; + memcpy((char *) man->mf_data, + (char *) smc->mib.fddiSMTManufacturerData, + sizeof(man->mf_data)) ; +} + +/* + * fill user field + */ +static void smt_fill_user(struct s_smc *smc, struct smp_p_user *user) +{ + SMTSETPARA(user,SMT_P_USER) ; + memcpy((char *) user->us_data, + (char *) smc->mib.fddiSMTUserData, + sizeof(user->us_data)) ; +} + +/* + * fill set count + */ +static void smt_fill_setcount(struct s_smc *smc, struct smt_p_setcount *setcount) +{ + SK_UNUSED(smc) ; + SMTSETPARA(setcount,SMT_P_SETCOUNT) ; + setcount->count = smc->mib.fddiSMTSetCount.count ; + memcpy((char *)setcount->timestamp, + (char *)smc->mib.fddiSMTSetCount.timestamp,8) ; +} + +/* + * fill echo data + */ +static void smt_fill_echo(struct s_smc *smc, struct smt_p_echo *echo, u_long seed, + int len) +{ + u_char *p ; + + SK_UNUSED(smc) ; + SMTSETPARA(echo,SMT_P_ECHODATA) ; + echo->para.p_len = len ; + for (p = echo->ec_data ; len ; len--) { + *p++ = (u_char) seed ; + seed += 13 ; + } +} + +/* + * clear DNA and UNA + * called from CFM if configuration changes + */ +static void smt_clear_una_dna(struct s_smc *smc) +{ + smc->mib.m[MAC0].fddiMACUpstreamNbr = SMT_Unknown ; + smc->mib.m[MAC0].fddiMACDownstreamNbr = SMT_Unknown ; +} + +static void smt_clear_old_una_dna(struct s_smc *smc) +{ + smc->mib.m[MAC0].fddiMACOldUpstreamNbr = SMT_Unknown ; + smc->mib.m[MAC0].fddiMACOldDownstreamNbr = SMT_Unknown ; +} + +u_long smt_get_tid(struct s_smc *smc) +{ + u_long tid ; + while ((tid = ++(smc->sm.smt_tid) ^ SMT_TID_MAGIC) == 0) + ; + return tid & 0x3fffffffL; +} + + +/* + * table of parameter lengths + */ +static const struct smt_pdef { + int ptype ; + int plen ; + const char *pswap ; +} smt_pdef[] = { + { SMT_P_UNA, sizeof(struct smt_p_una) , + SWAP_SMT_P_UNA } , + { SMT_P_SDE, sizeof(struct smt_p_sde) , + SWAP_SMT_P_SDE } , + { SMT_P_STATE, sizeof(struct smt_p_state) , + SWAP_SMT_P_STATE } , + { SMT_P_TIMESTAMP,sizeof(struct smt_p_timestamp) , + SWAP_SMT_P_TIMESTAMP } , + { SMT_P_POLICY, sizeof(struct smt_p_policy) , + SWAP_SMT_P_POLICY } , + { SMT_P_LATENCY, sizeof(struct smt_p_latency) , + SWAP_SMT_P_LATENCY } , + { SMT_P_NEIGHBORS,sizeof(struct smt_p_neighbor) , + SWAP_SMT_P_NEIGHBORS } , + { SMT_P_PATH, sizeof(struct smt_p_path) , + SWAP_SMT_P_PATH } , + { SMT_P_MAC_STATUS,sizeof(struct smt_p_mac_status) , + SWAP_SMT_P_MAC_STATUS } , + { SMT_P_LEM, sizeof(struct smt_p_lem) , + SWAP_SMT_P_LEM } , + { SMT_P_MAC_COUNTER,sizeof(struct smt_p_mac_counter) , + SWAP_SMT_P_MAC_COUNTER } , + { SMT_P_MAC_FNC,sizeof(struct smt_p_mac_fnc) , + SWAP_SMT_P_MAC_FNC } , + { SMT_P_PRIORITY,sizeof(struct smt_p_priority) , + SWAP_SMT_P_PRIORITY } , + { SMT_P_EB,sizeof(struct smt_p_eb) , + SWAP_SMT_P_EB } , + { SMT_P_MANUFACTURER,sizeof(struct smp_p_manufacturer) , + SWAP_SMT_P_MANUFACTURER } , + { SMT_P_REASON, sizeof(struct smt_p_reason) , + SWAP_SMT_P_REASON } , + { SMT_P_REFUSED, sizeof(struct smt_p_refused) , + SWAP_SMT_P_REFUSED } , + { SMT_P_VERSION, sizeof(struct smt_p_version) , + SWAP_SMT_P_VERSION } , +#ifdef ESS + { SMT_P0015, sizeof(struct smt_p_0015) , SWAP_SMT_P0015 } , + { SMT_P0016, sizeof(struct smt_p_0016) , SWAP_SMT_P0016 } , + { SMT_P0017, sizeof(struct smt_p_0017) , SWAP_SMT_P0017 } , + { SMT_P0018, sizeof(struct smt_p_0018) , SWAP_SMT_P0018 } , + { SMT_P0019, sizeof(struct smt_p_0019) , SWAP_SMT_P0019 } , + { SMT_P001A, sizeof(struct smt_p_001a) , SWAP_SMT_P001A } , + { SMT_P001B, sizeof(struct smt_p_001b) , SWAP_SMT_P001B } , + { SMT_P001C, sizeof(struct smt_p_001c) , SWAP_SMT_P001C } , + { SMT_P001D, sizeof(struct smt_p_001d) , SWAP_SMT_P001D } , +#endif +#if 0 + { SMT_P_FSC, sizeof(struct smt_p_fsc) , + SWAP_SMT_P_FSC } , +#endif + + { SMT_P_SETCOUNT,0, SWAP_SMT_P_SETCOUNT } , + { SMT_P1048, 0, SWAP_SMT_P1048 } , + { SMT_P208C, 0, SWAP_SMT_P208C } , + { SMT_P208D, 0, SWAP_SMT_P208D } , + { SMT_P208E, 0, SWAP_SMT_P208E } , + { SMT_P208F, 0, SWAP_SMT_P208F } , + { SMT_P2090, 0, SWAP_SMT_P2090 } , +#ifdef ESS + { SMT_P320B, sizeof(struct smt_p_320b) , SWAP_SMT_P320B } , + { SMT_P320F, sizeof(struct smt_p_320f) , SWAP_SMT_P320F } , + { SMT_P3210, sizeof(struct smt_p_3210) , SWAP_SMT_P3210 } , +#endif + { SMT_P4050, 0, SWAP_SMT_P4050 } , + { SMT_P4051, 0, SWAP_SMT_P4051 } , + { SMT_P4052, 0, SWAP_SMT_P4052 } , + { SMT_P4053, 0, SWAP_SMT_P4053 } , +} ; + +#define N_SMT_PLEN ARRAY_SIZE(smt_pdef) + +int smt_check_para(struct s_smc *smc, struct smt_header *sm, + const u_short list[]) +{ + const u_short *p = list ; + while (*p) { + if (!sm_to_para(smc,sm,(int) *p)) { + DB_SMT("SMT: smt_check_para - missing para %x\n",*p,0); + return -1; + } + p++ ; + } + return 0; +} + +void *sm_to_para(struct s_smc *smc, struct smt_header *sm, int para) +{ + char *p ; + int len ; + int plen ; + void *found = NULL; + + SK_UNUSED(smc) ; + + len = sm->smt_len ; + p = (char *)(sm+1) ; /* pointer to info */ + while (len > 0 ) { + if (((struct smt_para *)p)->p_type == para) + found = (void *) p ; + plen = ((struct smt_para *)p)->p_len + PARA_LEN ; + p += plen ; + len -= plen ; + if (len < 0) { + DB_SMT("SMT : sm_to_para - length error %d\n",plen,0) ; + return NULL; + } + if ((plen & 3) && (para != SMT_P_ECHODATA)) { + DB_SMT("SMT : sm_to_para - odd length %d\n",plen,0) ; + return NULL; + } + if (found) + return found; + } + return NULL; +} + +#if 0 +/* + * send ANTC data test frame + */ +void fddi_send_antc(struct s_smc *smc, struct fddi_addr *dest) +{ + SK_UNUSED(smc) ; + SK_UNUSED(dest) ; +#if 0 + SMbuf *mb ; + struct smt_header *smt ; + int i ; + char *p ; + + mb = smt_get_mbuf() ; + mb->sm_len = 3000+12 ; + p = smtod(mb, char *) + 12 ; + for (i = 0 ; i < 3000 ; i++) + *p++ = 1 << (i&7) ; + + smt = smtod(mb, struct smt_header *) ; + smt->smt_dest = *dest ; + smt->smt_source = smc->mib.m[MAC0].fddiMACSMTAddress ; + smt_send_mbuf(smc,mb,FC_ASYNC_LLC) ; +#endif +} +#endif + +#ifdef DEBUG +char *addr_to_string(struct fddi_addr *addr) +{ + int i ; + static char string[6*3] = "****" ; + + for (i = 0 ; i < 6 ; i++) { + string[i * 3] = hex_asc_hi(addr->a[i]); + string[i * 3 + 1] = hex_asc_lo(addr->a[i]); + string[i * 3 + 2] = ':'; + } + string[5 * 3 + 2] = 0; + return string; +} +#endif + +/* + * return static mac index + */ +static int mac_index(struct s_smc *smc, int mac) +{ + SK_UNUSED(mac) ; +#ifdef CONCENTRATOR + SK_UNUSED(smc) ; + return NUMPHYS + 1; +#else + return (smc->s.sas == SMT_SAS) ? 2 : 3; +#endif +} + +/* + * return static phy index + */ +static int phy_index(struct s_smc *smc, int phy) +{ + SK_UNUSED(smc) ; + return phy + 1; +} + +/* + * return dynamic mac connection resource index + */ +static int mac_con_resource_index(struct s_smc *smc, int mac) +{ +#ifdef CONCENTRATOR + SK_UNUSED(smc) ; + SK_UNUSED(mac) ; + return entity_to_index(smc, cem_get_downstream(smc, ENTITY_MAC)); +#else + SK_UNUSED(mac) ; + switch (smc->mib.fddiSMTCF_State) { + case SC9_C_WRAP_A : + case SC5_THRU_B : + case SC11_C_WRAP_S : + return 1; + case SC10_C_WRAP_B : + case SC4_THRU_A : + return 2; + } + return smc->s.sas == SMT_SAS ? 2 : 3; +#endif +} + +/* + * return dynamic phy connection resource index + */ +static int phy_con_resource_index(struct s_smc *smc, int phy) +{ +#ifdef CONCENTRATOR + return entity_to_index(smc, cem_get_downstream(smc, ENTITY_PHY(phy))) ; +#else + switch (smc->mib.fddiSMTCF_State) { + case SC9_C_WRAP_A : + return phy == PA ? 3 : 2; + case SC10_C_WRAP_B : + return phy == PA ? 1 : 3; + case SC4_THRU_A : + return phy == PA ? 3 : 1; + case SC5_THRU_B : + return phy == PA ? 2 : 3; + case SC11_C_WRAP_S : + return 2; + } + return phy; +#endif +} + +#ifdef CONCENTRATOR +static int entity_to_index(struct s_smc *smc, int e) +{ + if (e == ENTITY_MAC) + return mac_index(smc, 1); + else + return phy_index(smc, e - ENTITY_PHY(0)); +} +#endif + +#ifdef LITTLE_ENDIAN +static int smt_swap_short(u_short s) +{ + return ((s>>8)&0xff) | ((s&0xff)<<8); +} + +void smt_swap_para(struct smt_header *sm, int len, int direction) +/* int direction; 0 encode 1 decode */ +{ + struct smt_para *pa ; + const struct smt_pdef *pd ; + char *p ; + int plen ; + int type ; + int i ; + +/* printf("smt_swap_para sm %x len %d dir %d\n", + sm,len,direction) ; + */ + smt_string_swap((char *)sm,SWAP_SMTHEADER,len) ; + + /* swap args */ + len -= sizeof(struct smt_header) ; + + p = (char *) (sm + 1) ; + while (len > 0) { + pa = (struct smt_para *) p ; + plen = pa->p_len ; + type = pa->p_type ; + pa->p_type = smt_swap_short(pa->p_type) ; + pa->p_len = smt_swap_short(pa->p_len) ; + if (direction) { + plen = pa->p_len ; + type = pa->p_type ; + } + /* + * note: paras can have 0 length ! + */ + if (plen < 0) + break ; + plen += PARA_LEN ; + for (i = N_SMT_PLEN, pd = smt_pdef; i ; i--,pd++) { + if (pd->ptype == type) + break ; + } + if (i && pd->pswap) { + smt_string_swap(p+PARA_LEN,pd->pswap,len) ; + } + len -= plen ; + p += plen ; + } +} + +static void smt_string_swap(char *data, const char *format, int len) +{ + const char *open_paren = NULL ; + int x ; + + while (len > 0 && *format) { + switch (*format) { + case '[' : + open_paren = format ; + break ; + case ']' : + format = open_paren ; + break ; + case '1' : + case '2' : + case '3' : + case '4' : + case '5' : + case '6' : + case '7' : + case '8' : + case '9' : + data += *format - '0' ; + len -= *format - '0' ; + break ; + case 'c': + data++ ; + len-- ; + break ; + case 's' : + x = data[0] ; + data[0] = data[1] ; + data[1] = x ; + data += 2 ; + len -= 2 ; + break ; + case 'l' : + x = data[0] ; + data[0] = data[3] ; + data[3] = x ; + x = data[1] ; + data[1] = data[2] ; + data[2] = x ; + data += 4 ; + len -= 4 ; + break ; + } + format++ ; + } +} +#else +void smt_swap_para(struct smt_header *sm, int len, int direction) +/* int direction; 0 encode 1 decode */ +{ + SK_UNUSED(sm) ; + SK_UNUSED(len) ; + SK_UNUSED(direction) ; +} +#endif + +/* + * PMF actions + */ +int smt_action(struct s_smc *smc, int class, int code, int index) +{ + int event ; + int port ; + DB_SMT("SMT: action %d code %d\n",class,code) ; + switch(class) { + case SMT_STATION_ACTION : + switch(code) { + case SMT_STATION_ACTION_CONNECT : + smc->mib.fddiSMTRemoteDisconnectFlag = FALSE ; + queue_event(smc,EVENT_ECM,EC_CONNECT) ; + break ; + case SMT_STATION_ACTION_DISCONNECT : + queue_event(smc,EVENT_ECM,EC_DISCONNECT) ; + smc->mib.fddiSMTRemoteDisconnectFlag = TRUE ; + RS_SET(smc,RS_DISCONNECT) ; + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, (u_long) + FDDI_SMT_EVENT, (u_long) FDDI_REMOTE_DISCONNECT, + smt_get_event_word(smc)); + break ; + case SMT_STATION_ACTION_PATHTEST : + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, (u_long) + FDDI_SMT_EVENT, (u_long) FDDI_PATH_TEST, + smt_get_event_word(smc)); + break ; + case SMT_STATION_ACTION_SELFTEST : + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, (u_long) + FDDI_SMT_EVENT, (u_long) FDDI_REMOTE_SELF_TEST, + smt_get_event_word(smc)); + break ; + case SMT_STATION_ACTION_DISABLE_A : + if (smc->y[PA].pc_mode == PM_PEER) { + RS_SET(smc,RS_EVENT) ; + queue_event(smc,EVENT_PCM+PA,PC_DISABLE) ; + } + break ; + case SMT_STATION_ACTION_DISABLE_B : + if (smc->y[PB].pc_mode == PM_PEER) { + RS_SET(smc,RS_EVENT) ; + queue_event(smc,EVENT_PCM+PB,PC_DISABLE) ; + } + break ; + case SMT_STATION_ACTION_DISABLE_M : + for (port = 0 ; port < NUMPHYS ; port++) { + if (smc->mib.p[port].fddiPORTMy_Type != TM) + continue ; + RS_SET(smc,RS_EVENT) ; + queue_event(smc,EVENT_PCM+port,PC_DISABLE) ; + } + break ; + default : + return 1; + } + break ; + case SMT_PORT_ACTION : + switch(code) { + case SMT_PORT_ACTION_ENABLE : + event = PC_ENABLE ; + break ; + case SMT_PORT_ACTION_DISABLE : + event = PC_DISABLE ; + break ; + case SMT_PORT_ACTION_MAINT : + event = PC_MAINT ; + break ; + case SMT_PORT_ACTION_START : + event = PC_START ; + break ; + case SMT_PORT_ACTION_STOP : + event = PC_STOP ; + break ; + default : + return 1; + } + queue_event(smc,EVENT_PCM+index,event) ; + break ; + default : + return 1; + } + return 0; +} + +/* + * canonical conversion of <len> bytes beginning form *data + */ +#ifdef USE_CAN_ADDR +static void hwm_conv_can(struct s_smc *smc, char *data, int len) +{ + int i ; + + SK_UNUSED(smc) ; + + for (i = len; i ; i--, data++) + *data = bitrev8(*data); +} +#endif + +#endif /* no SLIM_SMT */ + diff --git a/kernel/drivers/net/fddi/skfp/smtdef.c b/kernel/drivers/net/fddi/skfp/smtdef.c new file mode 100644 index 000000000..1acab0b36 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/smtdef.c @@ -0,0 +1,355 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + SMT/CMT defaults +*/ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" + +#ifndef OEM_USER_DATA +#define OEM_USER_DATA "SK-NET FDDI V2.0 Userdata" +#endif + +#ifndef lint +static const char ID_sccs[] = "@(#)smtdef.c 2.53 99/08/11 (C) SK " ; +#endif + +/* + * defaults + */ +#define TTMS(x) ((u_long)(x)*1000L) +#define TTS(x) ((u_long)(x)*1000000L) +#define TTUS(x) ((u_long)(x)) + +#define DEFAULT_TB_MIN TTMS(5) +#define DEFAULT_TB_MAX TTMS(50) +#define DEFAULT_C_MIN TTUS(1600) +#define DEFAULT_T_OUT TTMS(100+5) +#define DEFAULT_TL_MIN TTUS(30) +#define DEFAULT_LC_SHORT TTMS(50+5) +#define DEFAULT_LC_MEDIUM TTMS(500+20) +#define DEFAULT_LC_LONG TTS(5)+TTMS(50) +#define DEFAULT_LC_EXTENDED TTS(50)+TTMS(50) +#define DEFAULT_T_NEXT_9 TTMS(200+10) +#define DEFAULT_NS_MAX TTUS(1310) +#define DEFAULT_I_MAX TTMS(25) +#define DEFAULT_IN_MAX TTMS(40) +#define DEFAULT_TD_MIN TTMS(5) +#define DEFAULT_T_NON_OP TTS(1) +#define DEFAULT_T_STUCK TTS(8) +#define DEFAULT_T_DIRECT TTMS(370) +#define DEFAULT_T_JAM TTMS(370) +#define DEFAULT_T_ANNOUNCE TTMS(2500) +#define DEFAULT_D_MAX TTUS(1617) +#define DEFAULT_LEM_ALARM (8) +#define DEFAULT_LEM_CUTOFF (7) +#define DEFAULT_TEST_DONE TTS(1) +#define DEFAULT_CHECK_POLL TTS(1) +#define DEFAULT_POLL TTMS(50) + +/* + * LCT errors threshold + */ +#define DEFAULT_LCT_SHORT 1 +#define DEFAULT_LCT_MEDIUM 3 +#define DEFAULT_LCT_LONG 5 +#define DEFAULT_LCT_EXTEND 50 + +/* Forward declarations */ +void smt_reset_defaults(struct s_smc *smc, int level); +static void smt_init_mib(struct s_smc *smc, int level); +static int set_min_max(int maxflag, u_long mib, u_long limit, u_long *oper); + +#define MS2BCLK(x) ((x)*12500L) +#define US2BCLK(x) ((x)*1250L) + +void smt_reset_defaults(struct s_smc *smc, int level) +{ + struct smt_config *smt ; + int i ; + u_long smt_boot_time; + + + smt_init_mib(smc,level) ; + + smc->os.smc_version = SMC_VERSION ; + smt_boot_time = smt_get_time(); + for( i = 0; i < NUMMACS; i++ ) + smc->sm.last_tok_time[i] = smt_boot_time ; + smt = &smc->s ; + smt->attach_s = 0 ; + smt->build_ring_map = 1 ; + smt->sas = SMT_DAS ; + smt->numphys = NUMPHYS ; + smt->pcm_tb_min = DEFAULT_TB_MIN ; + smt->pcm_tb_max = DEFAULT_TB_MAX ; + smt->pcm_c_min = DEFAULT_C_MIN ; + smt->pcm_t_out = DEFAULT_T_OUT ; + smt->pcm_tl_min = DEFAULT_TL_MIN ; + smt->pcm_lc_short = DEFAULT_LC_SHORT ; + smt->pcm_lc_medium = DEFAULT_LC_MEDIUM ; + smt->pcm_lc_long = DEFAULT_LC_LONG ; + smt->pcm_lc_extended = DEFAULT_LC_EXTENDED ; + smt->pcm_t_next_9 = DEFAULT_T_NEXT_9 ; + smt->pcm_ns_max = DEFAULT_NS_MAX ; + smt->ecm_i_max = DEFAULT_I_MAX ; + smt->ecm_in_max = DEFAULT_IN_MAX ; + smt->ecm_td_min = DEFAULT_TD_MIN ; + smt->ecm_test_done = DEFAULT_TEST_DONE ; + smt->ecm_check_poll = DEFAULT_CHECK_POLL ; + smt->rmt_t_non_op = DEFAULT_T_NON_OP ; + smt->rmt_t_stuck = DEFAULT_T_STUCK ; + smt->rmt_t_direct = DEFAULT_T_DIRECT ; + smt->rmt_t_jam = DEFAULT_T_JAM ; + smt->rmt_t_announce = DEFAULT_T_ANNOUNCE ; + smt->rmt_t_poll = DEFAULT_POLL ; + smt->rmt_dup_mac_behavior = FALSE ; /* See Struct smt_config */ + smt->mac_d_max = DEFAULT_D_MAX ; + + smt->lct_short = DEFAULT_LCT_SHORT ; + smt->lct_medium = DEFAULT_LCT_MEDIUM ; + smt->lct_long = DEFAULT_LCT_LONG ; + smt->lct_extended = DEFAULT_LCT_EXTEND ; + +#ifndef SLIM_SMT +#ifdef ESS + if (level == 0) { + smc->ess.sync_bw_available = FALSE ; + smc->mib.fddiESSPayload = 0 ; + smc->mib.fddiESSOverhead = 0 ; + smc->mib.fddiESSMaxTNeg = (u_long)(- MS2BCLK(25)) ; + smc->mib.fddiESSMinSegmentSize = 1 ; + smc->mib.fddiESSCategory = SB_STATIC ; + smc->mib.fddiESSSynchTxMode = FALSE ; + smc->ess.raf_act_timer_poll = FALSE ; + smc->ess.timer_count = 7 ; /* first RAF alc req after 3s */ + } + smc->ess.local_sba_active = FALSE ; + smc->ess.sba_reply_pend = NULL ; +#endif +#ifdef SBA + smt_init_sba(smc,level) ; +#endif +#endif /* no SLIM_SMT */ +#ifdef TAG_MODE + if (level == 0) { + smc->hw.pci_fix_value = 0 ; + } +#endif +} + +/* + * manufacturer data + */ +static const char man_data[32] = +/* 01234567890123456789012345678901 */ + "xxxSK-NET FDDI SMT 7.3 - V2.8.8" ; + +static void smt_init_mib(struct s_smc *smc, int level) +{ + struct fddi_mib *mib ; + struct fddi_mib_p *pm ; + int port ; + int path ; + + mib = &smc->mib ; + if (level == 0) { + /* + * set EVERYTHING to ZERO + * EXCEPT hw and os + */ + memset(((char *)smc)+ + sizeof(struct s_smt_os)+sizeof(struct s_smt_hw), 0, + sizeof(struct s_smc) - + sizeof(struct s_smt_os) - sizeof(struct s_smt_hw)) ; + } + else { + mib->fddiSMTRemoteDisconnectFlag = 0 ; + mib->fddiSMTPeerWrapFlag = 0 ; + } + + mib->fddiSMTOpVersionId = 2 ; + mib->fddiSMTHiVersionId = 2 ; + mib->fddiSMTLoVersionId = 2 ; + memcpy((char *) mib->fddiSMTManufacturerData,man_data,32) ; + if (level == 0) { + strcpy(mib->fddiSMTUserData,OEM_USER_DATA) ; + } + mib->fddiSMTMIBVersionId = 1 ; + mib->fddiSMTMac_Ct = NUMMACS ; + mib->fddiSMTConnectionPolicy = POLICY_MM | POLICY_AA | POLICY_BB ; + + /* + * fddiSMTNonMaster_Ct and fddiSMTMaster_Ct are set in smt_fixup_mib + * s.sas is not set yet (is set in init driver) + */ + mib->fddiSMTAvailablePaths = MIB_PATH_P | MIB_PATH_S ; + + mib->fddiSMTConfigCapabilities = 0 ; /* no hold,no wrap_ab*/ + mib->fddiSMTTT_Notify = 10 ; + mib->fddiSMTStatRptPolicy = TRUE ; + mib->fddiSMTTrace_MaxExpiration = SEC2MIB(7) ; + mib->fddiSMTMACIndexes = INDEX_MAC ; + mib->fddiSMTStationStatus = MIB_SMT_STASTA_SEPA ; /* separated */ + + mib->m[MAC0].fddiMACIndex = INDEX_MAC ; + mib->m[MAC0].fddiMACFrameStatusFunctions = FSC_TYPE0 ; + mib->m[MAC0].fddiMACRequestedPaths = + MIB_P_PATH_LOCAL | + MIB_P_PATH_SEC_ALTER | + MIB_P_PATH_PRIM_ALTER ; + mib->m[MAC0].fddiMACAvailablePaths = MIB_PATH_P ; + mib->m[MAC0].fddiMACCurrentPath = MIB_PATH_PRIMARY ; + mib->m[MAC0].fddiMACT_MaxCapabilitiy = (u_long)(- MS2BCLK(165)) ; + mib->m[MAC0].fddiMACTVXCapabilitiy = (u_long)(- US2BCLK(52)) ; + if (level == 0) { + mib->m[MAC0].fddiMACTvxValue = (u_long)(- US2BCLK(27)) ; + mib->m[MAC0].fddiMACTvxValueMIB = (u_long)(- US2BCLK(27)) ; + mib->m[MAC0].fddiMACT_Req = (u_long)(- MS2BCLK(165)) ; + mib->m[MAC0].fddiMACT_ReqMIB = (u_long)(- MS2BCLK(165)) ; + mib->m[MAC0].fddiMACT_Max = (u_long)(- MS2BCLK(165)) ; + mib->m[MAC0].fddiMACT_MaxMIB = (u_long)(- MS2BCLK(165)) ; + mib->m[MAC0].fddiMACT_Min = (u_long)(- MS2BCLK(4)) ; + } + mib->m[MAC0].fddiMACHardwarePresent = TRUE ; + mib->m[MAC0].fddiMACMA_UnitdataEnable = TRUE ; + mib->m[MAC0].fddiMACFrameErrorThreshold = 1 ; + mib->m[MAC0].fddiMACNotCopiedThreshold = 1 ; + /* + * Path attributes + */ + for (path = 0 ; path < NUMPATHS ; path++) { + mib->a[path].fddiPATHIndex = INDEX_PATH + path ; + if (level == 0) { + mib->a[path].fddiPATHTVXLowerBound = + (u_long)(- US2BCLK(27)) ; + mib->a[path].fddiPATHT_MaxLowerBound = + (u_long)(- MS2BCLK(165)) ; + mib->a[path].fddiPATHMaxT_Req = + (u_long)(- MS2BCLK(165)) ; + } + } + + + /* + * Port attributes + */ + pm = mib->p ; + for (port = 0 ; port < NUMPHYS ; port++) { + /* + * set MIB pointer in phy + */ + /* Attention: don't initialize mib pointer here! */ + /* It must be initialized during phase 2 */ + smc->y[port].mib = NULL; + mib->fddiSMTPORTIndexes[port] = port+INDEX_PORT ; + + pm->fddiPORTIndex = port+INDEX_PORT ; + pm->fddiPORTHardwarePresent = TRUE ; + if (level == 0) { + pm->fddiPORTLer_Alarm = DEFAULT_LEM_ALARM ; + pm->fddiPORTLer_Cutoff = DEFAULT_LEM_CUTOFF ; + } + /* + * fddiPORTRequestedPaths are set in pcmplc.c + * we don't know the port type yet ! + */ + pm->fddiPORTRequestedPaths[1] = 0 ; + pm->fddiPORTRequestedPaths[2] = 0 ; + pm->fddiPORTRequestedPaths[3] = 0 ; + pm->fddiPORTAvailablePaths = MIB_PATH_P ; + pm->fddiPORTPMDClass = MIB_PMDCLASS_MULTI ; + pm++ ; + } + + (void) smt_set_mac_opvalues(smc) ; +} + +int smt_set_mac_opvalues(struct s_smc *smc) +{ + int st ; + int st2 ; + + st = set_min_max(1,smc->mib.m[MAC0].fddiMACTvxValueMIB, + smc->mib.a[PATH0].fddiPATHTVXLowerBound, + &smc->mib.m[MAC0].fddiMACTvxValue) ; + st |= set_min_max(0,smc->mib.m[MAC0].fddiMACT_MaxMIB, + smc->mib.a[PATH0].fddiPATHT_MaxLowerBound, + &smc->mib.m[MAC0].fddiMACT_Max) ; + st |= (st2 = set_min_max(0,smc->mib.m[MAC0].fddiMACT_ReqMIB, + smc->mib.a[PATH0].fddiPATHMaxT_Req, + &smc->mib.m[MAC0].fddiMACT_Req)) ; + if (st2) { + /* Treq attribute changed remotely. So send an AIX_EVENT to the + * user + */ + AIX_EVENT(smc, (u_long) FDDI_RING_STATUS, (u_long) + FDDI_SMT_EVENT, (u_long) FDDI_REMOTE_T_REQ, + smt_get_event_word(smc)); + } + return st; +} + +void smt_fixup_mib(struct s_smc *smc) +{ +#ifdef CONCENTRATOR + switch (smc->s.sas) { + case SMT_SAS : + smc->mib.fddiSMTNonMaster_Ct = 1 ; + break ; + case SMT_DAS : + smc->mib.fddiSMTNonMaster_Ct = 2 ; + break ; + case SMT_NAC : + smc->mib.fddiSMTNonMaster_Ct = 0 ; + break ; + } + smc->mib.fddiSMTMaster_Ct = NUMPHYS - smc->mib.fddiSMTNonMaster_Ct ; +#else + switch (smc->s.sas) { + case SMT_SAS : + smc->mib.fddiSMTNonMaster_Ct = 1 ; + break ; + case SMT_DAS : + smc->mib.fddiSMTNonMaster_Ct = 2 ; + break ; + } + smc->mib.fddiSMTMaster_Ct = 0 ; +#endif +} + +/* + * determine new setting for operational value + * if limit is lower than mib + * use limit + * else + * use mib + * NOTE : numbers are negative, negate comparison ! + */ +static int set_min_max(int maxflag, u_long mib, u_long limit, u_long *oper) +{ + u_long old ; + old = *oper ; + if ((limit > mib) ^ maxflag) + *oper = limit ; + else + *oper = mib ; + return old != *oper; +} + diff --git a/kernel/drivers/net/fddi/skfp/smtinit.c b/kernel/drivers/net/fddi/skfp/smtinit.c new file mode 100644 index 000000000..e3a0c0bc2 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/smtinit.c @@ -0,0 +1,125 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + Init SMT + call all module level initialization routines +*/ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)smtinit.c 1.15 97/05/06 (C) SK " ; +#endif + +void init_fddi_driver(struct s_smc *smc, u_char *mac_addr); + +/* define global debug variable */ +#if defined(DEBUG) && !defined(DEBUG_BRD) +struct smt_debug debug; +#endif + +#ifndef MULT_OEM +#define OEMID(smc,i) oem_id[i] + extern u_char oem_id[] ; +#else /* MULT_OEM */ +#define OEMID(smc,i) smc->hw.oem_id->oi_mark[i] + extern struct s_oem_ids oem_ids[] ; +#endif /* MULT_OEM */ + +/* + * Set OEM specific values + * + * Can not be called in smt_reset_defaults, because it is not sure that + * the OEM ID is already defined. + */ +static void set_oem_spec_val(struct s_smc *smc) +{ + struct fddi_mib *mib ; + + mib = &smc->mib ; + + /* + * set IBM specific values + */ + if (OEMID(smc,0) == 'I') { + mib->fddiSMTConnectionPolicy = POLICY_MM ; + } +} + +/* + * Init SMT + */ +int init_smt(struct s_smc *smc, u_char *mac_addr) +/* u_char *mac_addr; canonical address or NULL */ +{ + int p ; + +#if defined(DEBUG) && !defined(DEBUG_BRD) + debug.d_smt = 0 ; + debug.d_smtf = 0 ; + debug.d_rmt = 0 ; + debug.d_ecm = 0 ; + debug.d_pcm = 0 ; + debug.d_cfm = 0 ; + + debug.d_plc = 0 ; +#ifdef ESS + debug.d_ess = 0 ; +#endif +#ifdef SBA + debug.d_sba = 0 ; +#endif +#endif /* DEBUG && !DEBUG_BRD */ + + /* First initialize the ports mib->pointers */ + for ( p = 0; p < NUMPHYS; p ++ ) { + smc->y[p].mib = & smc->mib.p[p] ; + } + + set_oem_spec_val(smc) ; + (void) smt_set_mac_opvalues(smc) ; + init_fddi_driver(smc,mac_addr) ; /* HW driver */ + smt_fixup_mib(smc) ; /* update values that depend on s.sas */ + + ev_init(smc) ; /* event queue */ +#ifndef SLIM_SMT + smt_init_evc(smc) ; /* evcs in MIB */ +#endif /* no SLIM_SMT */ + smt_timer_init(smc) ; /* timer package */ + smt_agent_init(smc) ; /* SMT frame manager */ + + pcm_init(smc) ; /* PCM state machine */ + ecm_init(smc) ; /* ECM state machine */ + cfm_init(smc) ; /* CFM state machine */ + rmt_init(smc) ; /* RMT state machine */ + + for (p = 0 ; p < NUMPHYS ; p++) { + pcm(smc,p,0) ; /* PCM A state machine */ + } + ecm(smc,0) ; /* ECM state machine */ + cfm(smc,0) ; /* CFM state machine */ + rmt(smc,0) ; /* RMT state machine */ + + smt_agent_task(smc) ; /* NIF FSM etc */ + + PNMI_INIT(smc) ; /* PNMI initialization */ + + return 0; +} + diff --git a/kernel/drivers/net/fddi/skfp/smttimer.c b/kernel/drivers/net/fddi/skfp/smttimer.c new file mode 100644 index 000000000..531795e98 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/smttimer.c @@ -0,0 +1,156 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + SMT timer +*/ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" + +#ifndef lint +static const char ID_sccs[] = "@(#)smttimer.c 2.4 97/08/04 (C) SK " ; +#endif + +static void timer_done(struct s_smc *smc, int restart); + +void smt_timer_init(struct s_smc *smc) +{ + smc->t.st_queue = NULL; + smc->t.st_fast.tm_active = FALSE ; + smc->t.st_fast.tm_next = NULL; + hwt_init(smc) ; +} + +void smt_timer_stop(struct s_smc *smc, struct smt_timer *timer) +{ + struct smt_timer **prev ; + struct smt_timer *tm ; + + /* + * remove timer from queue + */ + timer->tm_active = FALSE ; + if (smc->t.st_queue == timer && !timer->tm_next) { + hwt_stop(smc) ; + } + for (prev = &smc->t.st_queue ; (tm = *prev) ; prev = &tm->tm_next ) { + if (tm == timer) { + *prev = tm->tm_next ; + if (tm->tm_next) { + tm->tm_next->tm_delta += tm->tm_delta ; + } + return ; + } + } +} + +void smt_timer_start(struct s_smc *smc, struct smt_timer *timer, u_long time, + u_long token) +{ + struct smt_timer **prev ; + struct smt_timer *tm ; + u_long delta = 0 ; + + time /= 16 ; /* input is uS, clock ticks are 16uS */ + if (!time) + time = 1 ; + smt_timer_stop(smc,timer) ; + timer->tm_smc = smc ; + timer->tm_token = token ; + timer->tm_active = TRUE ; + if (!smc->t.st_queue) { + smc->t.st_queue = timer ; + timer->tm_next = NULL; + timer->tm_delta = time ; + hwt_start(smc,time) ; + return ; + } + /* + * timer correction + */ + timer_done(smc,0) ; + + /* + * find position in queue + */ + delta = 0 ; + for (prev = &smc->t.st_queue ; (tm = *prev) ; prev = &tm->tm_next ) { + if (delta + tm->tm_delta > time) { + break ; + } + delta += tm->tm_delta ; + } + /* insert in queue */ + *prev = timer ; + timer->tm_next = tm ; + timer->tm_delta = time - delta ; + if (tm) + tm->tm_delta -= timer->tm_delta ; + /* + * start new with first + */ + hwt_start(smc,smc->t.st_queue->tm_delta) ; +} + +void smt_force_irq(struct s_smc *smc) +{ + smt_timer_start(smc,&smc->t.st_fast,32L, EV_TOKEN(EVENT_SMT,SM_FAST)); +} + +void smt_timer_done(struct s_smc *smc) +{ + timer_done(smc,1) ; +} + +static void timer_done(struct s_smc *smc, int restart) +{ + u_long delta ; + struct smt_timer *tm ; + struct smt_timer *next ; + struct smt_timer **last ; + int done = 0 ; + + delta = hwt_read(smc) ; + last = &smc->t.st_queue ; + tm = smc->t.st_queue ; + while (tm && !done) { + if (delta >= tm->tm_delta) { + tm->tm_active = FALSE ; + delta -= tm->tm_delta ; + last = &tm->tm_next ; + tm = tm->tm_next ; + } + else { + tm->tm_delta -= delta ; + delta = 0 ; + done = 1 ; + } + } + *last = NULL; + next = smc->t.st_queue ; + smc->t.st_queue = tm ; + + for ( tm = next ; tm ; tm = next) { + next = tm->tm_next ; + timer_event(smc,tm->tm_token) ; + } + + if (restart && smc->t.st_queue) + hwt_start(smc,smc->t.st_queue->tm_delta) ; +} + diff --git a/kernel/drivers/net/fddi/skfp/srf.c b/kernel/drivers/net/fddi/skfp/srf.c new file mode 100644 index 000000000..cc27dea34 --- /dev/null +++ b/kernel/drivers/net/fddi/skfp/srf.c @@ -0,0 +1,429 @@ +/****************************************************************************** + * + * (C)Copyright 1998,1999 SysKonnect, + * a business unit of Schneider & Koch & Co. Datensysteme GmbH. + * + * See the file "skfddi.c" for further information. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +/* + SMT 7.2 Status Response Frame Implementation + SRF state machine and frame generation +*/ + +#include "h/types.h" +#include "h/fddi.h" +#include "h/smc.h" +#include "h/smt_p.h" + +#define KERNEL +#include "h/smtstate.h" + +#ifndef SLIM_SMT +#ifndef BOOT + +#ifndef lint +static const char ID_sccs[] = "@(#)srf.c 1.18 97/08/04 (C) SK " ; +#endif + + +/* + * function declarations + */ +static void clear_all_rep(struct s_smc *smc); +static void clear_reported(struct s_smc *smc); +static void smt_send_srf(struct s_smc *smc); +static struct s_srf_evc *smt_get_evc(struct s_smc *smc, int code, int index); + +#define MAX_EVCS ARRAY_SIZE(smc->evcs) + +struct evc_init { + u_char code ; + u_char index ; + u_char n ; + u_short para ; +} ; + +static const struct evc_init evc_inits[] = { + { SMT_COND_SMT_PEER_WRAP, 0,1,SMT_P1048 } , + + { SMT_COND_MAC_DUP_ADDR, INDEX_MAC, NUMMACS,SMT_P208C } , + { SMT_COND_MAC_FRAME_ERROR, INDEX_MAC, NUMMACS,SMT_P208D } , + { SMT_COND_MAC_NOT_COPIED, INDEX_MAC, NUMMACS,SMT_P208E } , + { SMT_EVENT_MAC_NEIGHBOR_CHANGE, INDEX_MAC, NUMMACS,SMT_P208F } , + { SMT_EVENT_MAC_PATH_CHANGE, INDEX_MAC, NUMMACS,SMT_P2090 } , + + { SMT_COND_PORT_LER, INDEX_PORT,NUMPHYS,SMT_P4050 } , + { SMT_COND_PORT_EB_ERROR, INDEX_PORT,NUMPHYS,SMT_P4052 } , + { SMT_EVENT_PORT_CONNECTION, INDEX_PORT,NUMPHYS,SMT_P4051 } , + { SMT_EVENT_PORT_PATH_CHANGE, INDEX_PORT,NUMPHYS,SMT_P4053 } , +} ; + +#define MAX_INIT_EVC ARRAY_SIZE(evc_inits) + +void smt_init_evc(struct s_smc *smc) +{ + struct s_srf_evc *evc ; + const struct evc_init *init ; + unsigned int i ; + int index ; + int offset ; + + static u_char fail_safe = FALSE ; + + memset((char *)smc->evcs,0,sizeof(smc->evcs)) ; + + evc = smc->evcs ; + init = evc_inits ; + + for (i = 0 ; i < MAX_INIT_EVC ; i++) { + for (index = 0 ; index < init->n ; index++) { + evc->evc_code = init->code ; + evc->evc_para = init->para ; + evc->evc_index = init->index + index ; +#ifndef DEBUG + evc->evc_multiple = &fail_safe ; + evc->evc_cond_state = &fail_safe ; +#endif + evc++ ; + } + init++ ; + } + + if ((unsigned int) (evc - smc->evcs) > MAX_EVCS) { + SMT_PANIC(smc,SMT_E0127, SMT_E0127_MSG) ; + } + + /* + * conditions + */ + smc->evcs[0].evc_cond_state = &smc->mib.fddiSMTPeerWrapFlag ; + smc->evcs[1].evc_cond_state = + &smc->mib.m[MAC0].fddiMACDuplicateAddressCond ; + smc->evcs[2].evc_cond_state = + &smc->mib.m[MAC0].fddiMACFrameErrorFlag ; + smc->evcs[3].evc_cond_state = + &smc->mib.m[MAC0].fddiMACNotCopiedFlag ; + + /* + * events + */ + smc->evcs[4].evc_multiple = &smc->mib.m[MAC0].fddiMACMultiple_N ; + smc->evcs[5].evc_multiple = &smc->mib.m[MAC0].fddiMACMultiple_P ; + + offset = 6 ; + for (i = 0 ; i < NUMPHYS ; i++) { + /* + * conditions + */ + smc->evcs[offset + 0*NUMPHYS].evc_cond_state = + &smc->mib.p[i].fddiPORTLerFlag ; + smc->evcs[offset + 1*NUMPHYS].evc_cond_state = + &smc->mib.p[i].fddiPORTEB_Condition ; + + /* + * events + */ + smc->evcs[offset + 2*NUMPHYS].evc_multiple = + &smc->mib.p[i].fddiPORTMultiple_U ; + smc->evcs[offset + 3*NUMPHYS].evc_multiple = + &smc->mib.p[i].fddiPORTMultiple_P ; + offset++ ; + } +#ifdef DEBUG + for (i = 0, evc = smc->evcs ; i < MAX_EVCS ; i++, evc++) { + if (SMT_IS_CONDITION(evc->evc_code)) { + if (!evc->evc_cond_state) { + SMT_PANIC(smc,SMT_E0128, SMT_E0128_MSG) ; + } + evc->evc_multiple = &fail_safe ; + } + else { + if (!evc->evc_multiple) { + SMT_PANIC(smc,SMT_E0129, SMT_E0129_MSG) ; + } + evc->evc_cond_state = &fail_safe ; + } + } +#endif + smc->srf.TSR = smt_get_time() ; + smc->srf.sr_state = SR0_WAIT ; +} + +static struct s_srf_evc *smt_get_evc(struct s_smc *smc, int code, int index) +{ + unsigned int i ; + struct s_srf_evc *evc ; + + for (i = 0, evc = smc->evcs ; i < MAX_EVCS ; i++, evc++) { + if (evc->evc_code == code && evc->evc_index == index) + return evc; + } + return NULL; +} + +#define THRESHOLD_2 (2*TICKS_PER_SECOND) +#define THRESHOLD_32 (32*TICKS_PER_SECOND) + +#ifdef DEBUG +static const char * const srf_names[] = { + "None","MACPathChangeEvent", "MACNeighborChangeEvent", + "PORTPathChangeEvent", "PORTUndesiredConnectionAttemptEvent", + "SMTPeerWrapCondition", "SMTHoldCondition", + "MACFrameErrorCondition", "MACDuplicateAddressCondition", + "MACNotCopiedCondition", "PORTEBErrorCondition", + "PORTLerCondition" +} ; +#endif + +void smt_srf_event(struct s_smc *smc, int code, int index, int cond) +{ + struct s_srf_evc *evc ; + int cond_asserted = 0 ; + int cond_deasserted = 0 ; + int event_occurred = 0 ; + int tsr ; + int T_Limit = 2*TICKS_PER_SECOND ; + + if (code == SMT_COND_MAC_DUP_ADDR && cond) { + RS_SET(smc,RS_DUPADDR) ; + } + + if (code) { + DB_SMT("SRF: %s index %d\n",srf_names[code],index) ; + + if (!(evc = smt_get_evc(smc,code,index))) { + DB_SMT("SRF : smt_get_evc() failed\n",0,0) ; + return ; + } + /* + * ignore condition if no change + */ + if (SMT_IS_CONDITION(code)) { + if (*evc->evc_cond_state == cond) + return ; + } + + /* + * set transition time stamp + */ + smt_set_timestamp(smc,smc->mib.fddiSMTTransitionTimeStamp) ; + if (SMT_IS_CONDITION(code)) { + DB_SMT("SRF: condition is %s\n",cond ? "ON":"OFF",0) ; + if (cond) { + *evc->evc_cond_state = TRUE ; + evc->evc_rep_required = TRUE ; + smc->srf.any_report = TRUE ; + cond_asserted = TRUE ; + } + else { + *evc->evc_cond_state = FALSE ; + cond_deasserted = TRUE ; + } + } + else { + if (evc->evc_rep_required) { + *evc->evc_multiple = TRUE ; + } + else { + evc->evc_rep_required = TRUE ; + *evc->evc_multiple = FALSE ; + } + smc->srf.any_report = TRUE ; + event_occurred = TRUE ; + } +#ifdef FDDI_MIB + snmp_srf_event(smc,evc) ; +#endif /* FDDI_MIB */ + } + tsr = smt_get_time() - smc->srf.TSR ; + + switch (smc->srf.sr_state) { + case SR0_WAIT : + /* SR01a */ + if (cond_asserted && tsr < T_Limit) { + smc->srf.SRThreshold = THRESHOLD_2 ; + smc->srf.sr_state = SR1_HOLDOFF ; + break ; + } + /* SR01b */ + if (cond_deasserted && tsr < T_Limit) { + smc->srf.sr_state = SR1_HOLDOFF ; + break ; + } + /* SR01c */ + if (event_occurred && tsr < T_Limit) { + smc->srf.sr_state = SR1_HOLDOFF ; + break ; + } + /* SR00b */ + if (cond_asserted && tsr >= T_Limit) { + smc->srf.SRThreshold = THRESHOLD_2 ; + smc->srf.TSR = smt_get_time() ; + smt_send_srf(smc) ; + break ; + } + /* SR00c */ + if (cond_deasserted && tsr >= T_Limit) { + smc->srf.TSR = smt_get_time() ; + smt_send_srf(smc) ; + break ; + } + /* SR00d */ + if (event_occurred && tsr >= T_Limit) { + smc->srf.TSR = smt_get_time() ; + smt_send_srf(smc) ; + break ; + } + /* SR00e */ + if (smc->srf.any_report && (u_long) tsr >= + smc->srf.SRThreshold) { + smc->srf.SRThreshold *= 2 ; + if (smc->srf.SRThreshold > THRESHOLD_32) + smc->srf.SRThreshold = THRESHOLD_32 ; + smc->srf.TSR = smt_get_time() ; + smt_send_srf(smc) ; + break ; + } + /* SR02 */ + if (!smc->mib.fddiSMTStatRptPolicy) { + smc->srf.sr_state = SR2_DISABLED ; + break ; + } + break ; + case SR1_HOLDOFF : + /* SR10b */ + if (tsr >= T_Limit) { + smc->srf.sr_state = SR0_WAIT ; + smc->srf.TSR = smt_get_time() ; + smt_send_srf(smc) ; + break ; + } + /* SR11a */ + if (cond_asserted) { + smc->srf.SRThreshold = THRESHOLD_2 ; + } + /* SR11b */ + /* SR11c */ + /* handled above */ + /* SR12 */ + if (!smc->mib.fddiSMTStatRptPolicy) { + smc->srf.sr_state = SR2_DISABLED ; + break ; + } + break ; + case SR2_DISABLED : + if (smc->mib.fddiSMTStatRptPolicy) { + smc->srf.sr_state = SR0_WAIT ; + smc->srf.TSR = smt_get_time() ; + smc->srf.SRThreshold = THRESHOLD_2 ; + clear_all_rep(smc) ; + break ; + } + break ; + } +} + +static void clear_all_rep(struct s_smc *smc) +{ + struct s_srf_evc *evc ; + unsigned int i ; + + for (i = 0, evc = smc->evcs ; i < MAX_EVCS ; i++, evc++) { + evc->evc_rep_required = FALSE ; + if (SMT_IS_CONDITION(evc->evc_code)) + *evc->evc_cond_state = FALSE ; + } + smc->srf.any_report = FALSE ; +} + +static void clear_reported(struct s_smc *smc) +{ + struct s_srf_evc *evc ; + unsigned int i ; + + smc->srf.any_report = FALSE ; + for (i = 0, evc = smc->evcs ; i < MAX_EVCS ; i++, evc++) { + if (SMT_IS_CONDITION(evc->evc_code)) { + if (*evc->evc_cond_state == FALSE) + evc->evc_rep_required = FALSE ; + else + smc->srf.any_report = TRUE ; + } + else { + evc->evc_rep_required = FALSE ; + *evc->evc_multiple = FALSE ; + } + } +} + +/* + * build and send SMT SRF frame + */ +static void smt_send_srf(struct s_smc *smc) +{ + + struct smt_header *smt ; + struct s_srf_evc *evc ; + SK_LOC_DECL(struct s_pcon,pcon) ; + SMbuf *mb ; + unsigned int i ; + + static const struct fddi_addr SMT_SRF_DA = { + { 0x80, 0x01, 0x43, 0x00, 0x80, 0x08 } + } ; + + /* + * build SMT header + */ + if (!smc->r.sm_ma_avail) + return ; + if (!(mb = smt_build_frame(smc,SMT_SRF,SMT_ANNOUNCE,0))) + return ; + + RS_SET(smc,RS_SOFTERROR) ; + + smt = smtod(mb, struct smt_header *) ; + smt->smt_dest = SMT_SRF_DA ; /* DA == SRF multicast */ + + /* + * setup parameter status + */ + pcon.pc_len = SMT_MAX_INFO_LEN ; /* max para length */ + pcon.pc_err = 0 ; /* no error */ + pcon.pc_badset = 0 ; /* no bad set count */ + pcon.pc_p = (void *) (smt + 1) ; /* paras start here */ + + smt_add_para(smc,&pcon,(u_short) SMT_P1033,0,0) ; + smt_add_para(smc,&pcon,(u_short) SMT_P1034,0,0) ; + + for (i = 0, evc = smc->evcs ; i < MAX_EVCS ; i++, evc++) { + if (evc->evc_rep_required) { + smt_add_para(smc,&pcon,evc->evc_para, + (int)evc->evc_index,0) ; + } + } + smt->smt_len = SMT_MAX_INFO_LEN - pcon.pc_len ; + mb->sm_len = smt->smt_len + sizeof(struct smt_header) ; + + DB_SMT("SRF: sending SRF at %x, len %d\n",smt,mb->sm_len) ; + DB_SMT("SRF: state SR%d Threshold %d\n", + smc->srf.sr_state,smc->srf.SRThreshold/TICKS_PER_SECOND) ; +#ifdef DEBUG + dump_smt(smc,smt,"SRF Send") ; +#endif + smt_send_frame(smc,mb,FC_SMT_INFO,0) ; + clear_reported(smc) ; +} + +#endif /* no BOOT */ +#endif /* no SLIM_SMT */ + |