diff options
Diffstat (limited to 'kernel/drivers/net/ethernet/realtek/Kconfig')
| -rw-r--r-- | kernel/drivers/net/ethernet/realtek/Kconfig | 115 |
1 files changed, 115 insertions, 0 deletions
diff --git a/kernel/drivers/net/ethernet/realtek/Kconfig b/kernel/drivers/net/ethernet/realtek/Kconfig new file mode 100644 index 000000000..ae5d02709 --- /dev/null +++ b/kernel/drivers/net/ethernet/realtek/Kconfig @@ -0,0 +1,115 @@ +# +# Realtek device configuration +# + +config NET_VENDOR_REALTEK + bool "Realtek devices" + default y + depends on PCI || (PARPORT && X86) + ---help--- + If you have a network (Ethernet) card belonging to this class, say Y + and read the Ethernet-HOWTO, available from + <http://www.tldp.org/docs.html#howto>. + + Note that the answer to this question doesn't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about Realtek devices. If you say Y, you will be asked for + your specific card in the following questions. + +if NET_VENDOR_REALTEK + +config ATP + tristate "AT-LAN-TEC/RealTek pocket adapter support" + depends on PARPORT && X86 + select CRC32 + ---help--- + This is a network (Ethernet) device which attaches to your parallel + port. Read <file:drivers/net/ethernet/realtek/atp.c> as well as the + Ethernet-HOWTO, available from <http://www.tldp.org/docs.html#howto>, + if you want to use this. If you intend to use this driver, you + should have said N to the "Parallel printer support", because the two + drivers don't like each other. + + To compile this driver as a module, choose M here: the module + will be called atp. + +config 8139CP + tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support" + depends on PCI + select CRC32 + select MII + ---help--- + This is a driver for the Fast Ethernet PCI network cards based on + the RTL8139C+ chips. If you have one of those, say Y and read + the Ethernet-HOWTO, available from + <http://www.tldp.org/docs.html#howto>. + + To compile this driver as a module, choose M here: the module + will be called 8139cp. This is recommended. + +config 8139TOO + tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support" + depends on PCI + select CRC32 + select MII + ---help--- + This is a driver for the Fast Ethernet PCI network cards based on + the RTL 8129/8130/8139 chips. If you have one of those, say Y and + read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>. + + To compile this driver as a module, choose M here: the module + will be called 8139too. This is recommended. + +config 8139TOO_PIO + bool "Use PIO instead of MMIO" + default y + depends on 8139TOO + ---help--- + This instructs the driver to use programmed I/O ports (PIO) instead + of PCI shared memory (MMIO). This can possibly solve some problems + in case your mainboard has memory consistency issues. If unsure, + say N. + +config 8139TOO_TUNE_TWISTER + bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)" + depends on 8139TOO + ---help--- + This implements a function which might come in handy in case you + are using low quality on long cabling. It is required for RealTek + RTL-8139 revision K boards, and totally unused otherwise. It tries + to match the transceiver to the cable characteristics. This is + experimental since hardly documented by the manufacturer. + If unsure, say Y. + +config 8139TOO_8129 + bool "Support for older RTL-8129/8130 boards" + depends on 8139TOO + ---help--- + This enables support for the older and uncommon RTL-8129 and + RTL-8130 chips, which support MII via an external transceiver, + instead of an internal one. Disabling this option will save some + memory by making the code size smaller. If unsure, say Y. + +config 8139_OLD_RX_RESET + bool "Use older RX-reset method" + depends on 8139TOO + ---help--- + The 8139too driver was recently updated to contain a more rapid + reset sequence, in the face of severe receive errors. This "new" + RX-reset method should be adequate for all boards. But if you + experience problems, you can enable this option to restore the + old RX-reset behavior. If unsure, say N. + +config R8169 + tristate "Realtek 8169 gigabit ethernet support" + depends on PCI + select FW_LOADER + select CRC32 + select MII + ---help--- + Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter. + + To compile this driver as a module, choose M here: the module + will be called r8169. This is recommended. + +endif # NET_VENDOR_REALTEK |