summaryrefslogtreecommitdiffstats
path: root/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c')
-rw-r--r--kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c304
1 files changed, 270 insertions, 34 deletions
diff --git a/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 06d8f3cfa..ce61b36b9 100644
--- a/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -57,6 +57,11 @@ static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
u16 offset);
static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw);
+/* Base table for registers values that change by MAC */
+const u32 ixgbe_mvals_8259X[IXGBE_MVALS_IDX_LIMIT] = {
+ IXGBE_MVALS_INIT(8259X)
+};
+
/**
* ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
* control
@@ -91,6 +96,8 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
case IXGBE_DEV_ID_82599_T3_LOM:
case IXGBE_DEV_ID_X540T:
case IXGBE_DEV_ID_X540T1:
+ case IXGBE_DEV_ID_X550T:
+ case IXGBE_DEV_ID_X550EM_X_10G_T:
supported = true;
break;
default:
@@ -290,13 +297,13 @@ s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw)
/* Setup flow control */
ret_val = ixgbe_setup_fc(hw);
- if (!ret_val)
- return 0;
+ if (ret_val)
+ return ret_val;
/* Clear adapter stopped flag */
hw->adapter_stopped = false;
- return ret_val;
+ return 0;
}
/**
@@ -463,7 +470,7 @@ s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw)
}
}
- if (hw->mac.type == ixgbe_mac_X540) {
+ if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) {
if (hw->phy.id == 0)
hw->phy.ops.identify(hw);
hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, MDIO_MMD_PCS, &i);
@@ -681,7 +688,7 @@ void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw)
bus->lan_id = bus->func;
/* check for a port swap */
- reg = IXGBE_READ_REG(hw, IXGBE_FACTPS);
+ reg = IXGBE_READ_REG(hw, IXGBE_FACTPS(hw));
if (reg & IXGBE_FACTPS_LFS)
bus->func ^= 0x1;
}
@@ -799,7 +806,7 @@ s32 ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw)
* Check for EEPROM present first.
* If not present leave as none
*/
- eec = IXGBE_READ_REG(hw, IXGBE_EEC);
+ eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
if (eec & IXGBE_EEC_PRES) {
eeprom->type = ixgbe_eeprom_spi;
@@ -1283,14 +1290,14 @@ static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw)
if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0)
return IXGBE_ERR_SWFW_SYNC;
- eec = IXGBE_READ_REG(hw, IXGBE_EEC);
+ eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
/* Request EEPROM Access */
eec |= IXGBE_EEC_REQ;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) {
- eec = IXGBE_READ_REG(hw, IXGBE_EEC);
+ eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
if (eec & IXGBE_EEC_GNT)
break;
udelay(5);
@@ -1299,7 +1306,7 @@ static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw)
/* Release if grant not acquired */
if (!(eec & IXGBE_EEC_GNT)) {
eec &= ~IXGBE_EEC_REQ;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
hw_dbg(hw, "Could not acquire EEPROM grant\n");
hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
@@ -1309,7 +1316,7 @@ static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw)
/* Setup EEPROM for Read/Write */
/* Clear CS and SK */
eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK);
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
return 0;
@@ -1333,7 +1340,7 @@ static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw)
* If the SMBI bit is 0 when we read it, then the bit will be
* set and we have the semaphore
*/
- swsm = IXGBE_READ_REG(hw, IXGBE_SWSM);
+ swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
if (!(swsm & IXGBE_SWSM_SMBI))
break;
usleep_range(50, 100);
@@ -1353,7 +1360,7 @@ static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw)
* If the SMBI bit is 0 when we read it, then the bit will be
* set and we have the semaphore
*/
- swsm = IXGBE_READ_REG(hw, IXGBE_SWSM);
+ swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
if (swsm & IXGBE_SWSM_SMBI) {
hw_dbg(hw, "Software semaphore SMBI between device drivers not granted.\n");
return IXGBE_ERR_EEPROM;
@@ -1362,16 +1369,16 @@ static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw)
/* Now get the semaphore between SW/FW through the SWESMBI bit */
for (i = 0; i < timeout; i++) {
- swsm = IXGBE_READ_REG(hw, IXGBE_SWSM);
+ swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
/* Set the SW EEPROM semaphore bit to request access */
swsm |= IXGBE_SWSM_SWESMBI;
- IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm);
+ IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
/* If we set the bit successfully then we got the
* semaphore.
*/
- swsm = IXGBE_READ_REG(hw, IXGBE_SWSM);
+ swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
if (swsm & IXGBE_SWSM_SWESMBI)
break;
@@ -1400,11 +1407,11 @@ static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw)
{
u32 swsm;
- swsm = IXGBE_READ_REG(hw, IXGBE_SWSM);
+ swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
/* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */
swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI);
- IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm);
+ IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
IXGBE_WRITE_FLUSH(hw);
}
@@ -1454,15 +1461,15 @@ static void ixgbe_standby_eeprom(struct ixgbe_hw *hw)
{
u32 eec;
- eec = IXGBE_READ_REG(hw, IXGBE_EEC);
+ eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
/* Toggle CS to flush commands */
eec |= IXGBE_EEC_CS;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
eec &= ~IXGBE_EEC_CS;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
}
@@ -1480,7 +1487,7 @@ static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
u32 mask;
u32 i;
- eec = IXGBE_READ_REG(hw, IXGBE_EEC);
+ eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
/*
* Mask is used to shift "count" bits of "data" out to the EEPROM
@@ -1501,7 +1508,7 @@ static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
else
eec &= ~IXGBE_EEC_DI;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
@@ -1518,7 +1525,7 @@ static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
/* We leave the "DI" bit set to "0" when we leave this routine. */
eec &= ~IXGBE_EEC_DI;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
}
@@ -1539,7 +1546,7 @@ static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
* the value of the "DO" bit. During this "shifting in" process the
* "DI" bit should always be clear.
*/
- eec = IXGBE_READ_REG(hw, IXGBE_EEC);
+ eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI);
@@ -1547,7 +1554,7 @@ static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
data = data << 1;
ixgbe_raise_eeprom_clk(hw, &eec);
- eec = IXGBE_READ_REG(hw, IXGBE_EEC);
+ eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
eec &= ~(IXGBE_EEC_DI);
if (eec & IXGBE_EEC_DO)
@@ -1571,7 +1578,7 @@ static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
* (setting the SK bit), then delay
*/
*eec = *eec | IXGBE_EEC_SK;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
}
@@ -1588,7 +1595,7 @@ static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
* delay
*/
*eec = *eec & ~IXGBE_EEC_SK;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
}
@@ -1601,19 +1608,19 @@ static void ixgbe_release_eeprom(struct ixgbe_hw *hw)
{
u32 eec;
- eec = IXGBE_READ_REG(hw, IXGBE_EEC);
+ eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
eec |= IXGBE_EEC_CS; /* Pull CS high */
eec &= ~IXGBE_EEC_SK; /* Lower SCK */
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
/* Stop requesting EEPROM access */
eec &= ~IXGBE_EEC_REQ;
- IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
+ IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
@@ -2157,10 +2164,11 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw)
/*
* In order to prevent Tx hangs when the internal Tx
* switch is enabled we must set the high water mark
- * to the maximum FCRTH value. This allows the Tx
- * switch to function even under heavy Rx workloads.
+ * to the Rx packet buffer size - 24KB. This allows
+ * the Tx switch to function even under heavy Rx
+ * workloads.
*/
- fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 32;
+ fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576;
}
IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth);
@@ -2469,6 +2477,9 @@ static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw)
hw_dbg(hw, "GIO Master Disable bit didn't clear - requesting resets\n");
hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
+ if (hw->mac.type >= ixgbe_mac_X550)
+ return 0;
+
/*
* Before proceeding, make sure that the PCIe block does not have
* transactions pending.
@@ -3898,3 +3909,228 @@ void ixgbe_enable_rx_generic(struct ixgbe_hw *hw)
}
}
}
+
+/** ixgbe_mng_present - returns true when management capability is present
+ * @hw: pointer to hardware structure
+ **/
+bool ixgbe_mng_present(struct ixgbe_hw *hw)
+{
+ u32 fwsm;
+
+ if (hw->mac.type < ixgbe_mac_82599EB)
+ return false;
+
+ fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM(hw));
+ fwsm &= IXGBE_FWSM_MODE_MASK;
+ return fwsm == IXGBE_FWSM_FW_MODE_PT;
+}
+
+/**
+ * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Set the link speed in the MAC and/or PHY register and restarts link.
+ */
+s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
+{
+ ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+ ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+ s32 status = 0;
+ u32 speedcnt = 0;
+ u32 i = 0;
+ bool autoneg, link_up = false;
+
+ /* Mask off requested but non-supported speeds */
+ status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg);
+ if (status)
+ return status;
+
+ speed &= link_speed;
+
+ /* Try each speed one by one, highest priority first. We do this in
+ * software because 10Gb fiber doesn't support speed autonegotiation.
+ */
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
+ speedcnt++;
+ highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+ false);
+ if (status)
+ return status;
+
+ if (link_speed == IXGBE_LINK_SPEED_10GB_FULL && link_up)
+ goto out;
+
+ /* Set the module link speed */
+ switch (hw->phy.media_type) {
+ case ixgbe_media_type_fiber:
+ hw->mac.ops.set_rate_select_speed(hw,
+ IXGBE_LINK_SPEED_10GB_FULL);
+ break;
+ case ixgbe_media_type_fiber_qsfp:
+ /* QSFP module automatically detects MAC link speed */
+ break;
+ default:
+ hw_dbg(hw, "Unexpected media type\n");
+ break;
+ }
+
+ /* Allow module to change analog characteristics (1G->10G) */
+ msleep(40);
+
+ status = hw->mac.ops.setup_mac_link(hw,
+ IXGBE_LINK_SPEED_10GB_FULL,
+ autoneg_wait_to_complete);
+ if (status)
+ return status;
+
+ /* Flap the Tx laser if it has not already been done */
+ if (hw->mac.ops.flap_tx_laser)
+ hw->mac.ops.flap_tx_laser(hw);
+
+ /* Wait for the controller to acquire link. Per IEEE 802.3ap,
+ * Section 73.10.2, we may have to wait up to 500ms if KR is
+ * attempted. 82599 uses the same timing for 10g SFI.
+ */
+ for (i = 0; i < 5; i++) {
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ status = hw->mac.ops.check_link(hw, &link_speed,
+ &link_up, false);
+ if (status)
+ return status;
+
+ if (link_up)
+ goto out;
+ }
+ }
+
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
+ speedcnt++;
+ if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
+ highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+ false);
+ if (status)
+ return status;
+
+ if (link_speed == IXGBE_LINK_SPEED_1GB_FULL && link_up)
+ goto out;
+
+ /* Set the module link speed */
+ switch (hw->phy.media_type) {
+ case ixgbe_media_type_fiber:
+ hw->mac.ops.set_rate_select_speed(hw,
+ IXGBE_LINK_SPEED_1GB_FULL);
+ break;
+ case ixgbe_media_type_fiber_qsfp:
+ /* QSFP module automatically detects link speed */
+ break;
+ default:
+ hw_dbg(hw, "Unexpected media type\n");
+ break;
+ }
+
+ /* Allow module to change analog characteristics (10G->1G) */
+ msleep(40);
+
+ status = hw->mac.ops.setup_mac_link(hw,
+ IXGBE_LINK_SPEED_1GB_FULL,
+ autoneg_wait_to_complete);
+ if (status)
+ return status;
+
+ /* Flap the Tx laser if it has not already been done */
+ if (hw->mac.ops.flap_tx_laser)
+ hw->mac.ops.flap_tx_laser(hw);
+
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+ false);
+ if (status)
+ return status;
+
+ if (link_up)
+ goto out;
+ }
+
+ /* We didn't get link. Configure back to the highest speed we tried,
+ * (if there was more than one). We call ourselves back with just the
+ * single highest speed that the user requested.
+ */
+ if (speedcnt > 1)
+ status = ixgbe_setup_mac_link_multispeed_fiber(hw,
+ highest_link_speed,
+ autoneg_wait_to_complete);
+
+out:
+ /* Set autoneg_advertised value based on input link speed */
+ hw->phy.autoneg_advertised = 0;
+
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
+
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL)
+ hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
+
+ return status;
+}
+
+/**
+ * ixgbe_set_soft_rate_select_speed - Set module link speed
+ * @hw: pointer to hardware structure
+ * @speed: link speed to set
+ *
+ * Set module link speed via the soft rate select.
+ */
+void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed)
+{
+ s32 status;
+ u8 rs, eeprom_data;
+
+ switch (speed) {
+ case IXGBE_LINK_SPEED_10GB_FULL:
+ /* one bit mask same as setting on */
+ rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
+ break;
+ case IXGBE_LINK_SPEED_1GB_FULL:
+ rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
+ break;
+ default:
+ hw_dbg(hw, "Invalid fixed module speed\n");
+ return;
+ }
+
+ /* Set RS0 */
+ status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+ IXGBE_I2C_EEPROM_DEV_ADDR2,
+ &eeprom_data);
+ if (status) {
+ hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
+ return;
+ }
+
+ eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
+
+ status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+ IXGBE_I2C_EEPROM_DEV_ADDR2,
+ eeprom_data);
+ if (status) {
+ hw_dbg(hw, "Failed to write Rx Rate Select RS0\n");
+ return;
+ }
+}