diff options
Diffstat (limited to 'kernel/drivers/net/ethernet/freescale/Kconfig')
| -rw-r--r-- | kernel/drivers/net/ethernet/freescale/Kconfig | 96 |
1 files changed, 96 insertions, 0 deletions
diff --git a/kernel/drivers/net/ethernet/freescale/Kconfig b/kernel/drivers/net/ethernet/freescale/Kconfig new file mode 100644 index 000000000..25e342572 --- /dev/null +++ b/kernel/drivers/net/ethernet/freescale/Kconfig @@ -0,0 +1,96 @@ +# +# Freescale device configuration +# + +config NET_VENDOR_FREESCALE + bool "Freescale devices" + default y + depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ + M523x || M527x || M5272 || M528x || M520x || M532x || \ + ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) + ---help--- + If you have a network (Ethernet) card belonging to this class, say Y + and read the Ethernet-HOWTO, available from + <http://www.tldp.org/docs.html#howto>. + + Note that the answer to this question doesn't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about Freescale devices. If you say Y, you will be + asked for your specific card in the following questions. + +if NET_VENDOR_FREESCALE + +config FEC + tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" + depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ + ARCH_MXC || SOC_IMX28) + default ARCH_MXC || SOC_IMX28 if ARM + select PHYLIB + select PTP_1588_CLOCK + ---help--- + Say Y here if you want to use the built-in 10/100 Fast ethernet + controller on some Motorola ColdFire and Freescale i.MX processors. + +config FEC_MPC52xx + tristate "FEC MPC52xx driver" + depends on PPC_MPC52xx && PPC_BESTCOMM + select CRC32 + select PHYLIB + select PPC_BESTCOMM_FEC + ---help--- + This option enables support for the MPC5200's on-chip + Fast Ethernet Controller + If compiled as module, it will be called fec_mpc52xx. + +config FEC_MPC52xx_MDIO + bool "FEC MPC52xx MDIO bus driver" + depends on FEC_MPC52xx + default y + ---help--- + The MPC5200's FEC can connect to the Ethernet either with + an external MII PHY chip or 10 Mbps 7-wire interface + (Motorola? industry standard). + If your board uses an external PHY connected to FEC, enable this. + If not sure, enable. + If compiled as module, it will be called fec_mpc52xx_phy. + +source "drivers/net/ethernet/freescale/fs_enet/Kconfig" + +config FSL_PQ_MDIO + tristate "Freescale PQ MDIO" + select PHYLIB + ---help--- + This driver supports the MDIO bus used by the gianfar and UCC drivers. + +config FSL_XGMAC_MDIO + tristate "Freescale XGMAC MDIO" + select PHYLIB + select OF_MDIO + ---help--- + This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and + on the FMan mEMAC (which supports both Clauses 22 and 45) + +config UCC_GETH + tristate "Freescale QE Gigabit Ethernet" + depends on QUICC_ENGINE + select FSL_PQ_MDIO + select PHYLIB + ---help--- + This driver supports the Gigabit Ethernet mode of the QUICC Engine, + which is available on some Freescale SOCs. + +config UGETH_TX_ON_DEMAND + bool "Transmit on Demand support" + depends on UCC_GETH + +config GIANFAR + tristate "Gianfar Ethernet" + depends on FSL_SOC + select FSL_PQ_MDIO + select PHYLIB + select CRC32 + ---help--- + This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, + and MPC86xx family of chips, and the FEC on the 8540. + +endif # NET_VENDOR_FREESCALE |