diff options
Diffstat (limited to 'kernel/drivers/gpu/drm/i915/intel_dvo.c')
-rw-r--r-- | kernel/drivers/gpu/drm/i915/intel_dvo.c | 137 |
1 files changed, 56 insertions, 81 deletions
diff --git a/kernel/drivers/gpu/drm/i915/intel_dvo.c b/kernel/drivers/gpu/drm/i915/intel_dvo.c index 770040ff4..8492053e0 100644 --- a/kernel/drivers/gpu/drm/i915/intel_dvo.c +++ b/kernel/drivers/gpu/drm/i915/intel_dvo.c @@ -80,7 +80,7 @@ static const struct intel_dvo_device intel_dvo_devices[] = { .name = "ch7017", .dvo_reg = DVOC, .slave_addr = 0x75, - .gpio = GMBUS_PORT_DPB, + .gpio = GMBUS_PIN_DPB, .dev_ops = &ch7017_ops, }, { @@ -97,7 +97,8 @@ struct intel_dvo { struct intel_dvo_device dev; - struct drm_display_mode *panel_fixed_mode; + struct intel_connector *attached_connector; + bool panel_wants_dither; }; @@ -196,68 +197,33 @@ static void intel_enable_dvo(struct intel_encoder *encoder) intel_dvo->dev.dev_ops->dpms(&intel_dvo->dev, true); } -/* Special dpms function to support cloning between dvo/sdvo/crt. */ -static void intel_dvo_dpms(struct drm_connector *connector, int mode) -{ - struct intel_dvo *intel_dvo = intel_attached_dvo(connector); - struct drm_crtc *crtc; - struct intel_crtc_state *config; - - /* dvo supports only 2 dpms states. */ - if (mode != DRM_MODE_DPMS_ON) - mode = DRM_MODE_DPMS_OFF; - - if (mode == connector->dpms) - return; - - connector->dpms = mode; - - /* Only need to change hw state when actually enabled */ - crtc = intel_dvo->base.base.crtc; - if (!crtc) { - intel_dvo->base.connectors_active = false; - return; - } - - /* We call connector dpms manually below in case pipe dpms doesn't - * change due to cloning. */ - if (mode == DRM_MODE_DPMS_ON) { - config = to_intel_crtc(crtc)->config; - - intel_dvo->base.connectors_active = true; - - intel_crtc_update_dpms(crtc); - - intel_dvo->dev.dev_ops->dpms(&intel_dvo->dev, true); - } else { - intel_dvo->dev.dev_ops->dpms(&intel_dvo->dev, false); - - intel_dvo->base.connectors_active = false; - - intel_crtc_update_dpms(crtc); - } - - intel_modeset_check_state(connector->dev); -} - static enum drm_mode_status intel_dvo_mode_valid(struct drm_connector *connector, struct drm_display_mode *mode) { struct intel_dvo *intel_dvo = intel_attached_dvo(connector); + const struct drm_display_mode *fixed_mode = + to_intel_connector(connector)->panel.fixed_mode; + int max_dotclk = to_i915(connector->dev)->max_dotclk_freq; + int target_clock = mode->clock; if (mode->flags & DRM_MODE_FLAG_DBLSCAN) return MODE_NO_DBLESCAN; /* XXX: Validate clock range */ - if (intel_dvo->panel_fixed_mode) { - if (mode->hdisplay > intel_dvo->panel_fixed_mode->hdisplay) + if (fixed_mode) { + if (mode->hdisplay > fixed_mode->hdisplay) return MODE_PANEL; - if (mode->vdisplay > intel_dvo->panel_fixed_mode->vdisplay) + if (mode->vdisplay > fixed_mode->vdisplay) return MODE_PANEL; + + target_clock = fixed_mode->clock; } + if (target_clock > max_dotclk) + return MODE_CLOCK_HIGH; + return intel_dvo->dev.dev_ops->mode_valid(&intel_dvo->dev, mode); } @@ -265,6 +231,8 @@ static bool intel_dvo_compute_config(struct intel_encoder *encoder, struct intel_crtc_state *pipe_config) { struct intel_dvo *intel_dvo = enc_to_dvo(encoder); + const struct drm_display_mode *fixed_mode = + intel_dvo->attached_connector->panel.fixed_mode; struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode; /* If we have timings from the BIOS for the panel, put them in @@ -272,21 +240,8 @@ static bool intel_dvo_compute_config(struct intel_encoder *encoder, * with the panel scaling set up to source from the H/VDisplay * of the original mode. */ - if (intel_dvo->panel_fixed_mode != NULL) { -#define C(x) adjusted_mode->x = intel_dvo->panel_fixed_mode->x - C(hdisplay); - C(hsync_start); - C(hsync_end); - C(htotal); - C(vdisplay); - C(vsync_start); - C(vsync_end); - C(vtotal); - C(clock); -#undef C - - drm_mode_set_crtcinfo(adjusted_mode, 0); - } + if (fixed_mode) + intel_fixed_panel_mode(fixed_mode, adjusted_mode); return true; } @@ -296,7 +251,7 @@ static void intel_dvo_pre_enable(struct intel_encoder *encoder) struct drm_device *dev = encoder->base.dev; struct drm_i915_private *dev_priv = dev->dev_private; struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc); - struct drm_display_mode *adjusted_mode = &crtc->config->base.adjusted_mode; + const struct drm_display_mode *adjusted_mode = &crtc->config->base.adjusted_mode; struct intel_dvo *intel_dvo = enc_to_dvo(encoder); int pipe = crtc->pipe; u32 dvo_val; @@ -330,11 +285,11 @@ static void intel_dvo_pre_enable(struct intel_encoder *encoder) dvo_val |= DVO_VSYNC_ACTIVE_HIGH; /*I915_WRITE(DVOB_SRCDIM, - (adjusted_mode->hdisplay << DVO_SRCDIM_HORIZONTAL_SHIFT) | - (adjusted_mode->VDisplay << DVO_SRCDIM_VERTICAL_SHIFT));*/ + (adjusted_mode->crtc_hdisplay << DVO_SRCDIM_HORIZONTAL_SHIFT) | + (adjusted_mode->crtc_vdisplay << DVO_SRCDIM_VERTICAL_SHIFT));*/ I915_WRITE(dvo_srcdim_reg, - (adjusted_mode->hdisplay << DVO_SRCDIM_HORIZONTAL_SHIFT) | - (adjusted_mode->vdisplay << DVO_SRCDIM_VERTICAL_SHIFT)); + (adjusted_mode->crtc_hdisplay << DVO_SRCDIM_HORIZONTAL_SHIFT) | + (adjusted_mode->crtc_vdisplay << DVO_SRCDIM_VERTICAL_SHIFT)); /*I915_WRITE(DVOB, dvo_val);*/ I915_WRITE(dvo_reg, dvo_val); } @@ -355,8 +310,9 @@ intel_dvo_detect(struct drm_connector *connector, bool force) static int intel_dvo_get_modes(struct drm_connector *connector) { - struct intel_dvo *intel_dvo = intel_attached_dvo(connector); struct drm_i915_private *dev_priv = connector->dev->dev_private; + const struct drm_display_mode *fixed_mode = + to_intel_connector(connector)->panel.fixed_mode; /* We should probably have an i2c driver get_modes function for those * devices which will have a fixed set of modes determined by the chip @@ -364,13 +320,13 @@ static int intel_dvo_get_modes(struct drm_connector *connector) * that's not the case. */ intel_ddc_get_modes(connector, - intel_gmbus_get_adapter(dev_priv, GMBUS_PORT_DPC)); + intel_gmbus_get_adapter(dev_priv, GMBUS_PIN_DPC)); if (!list_empty(&connector->probed_modes)) return 1; - if (intel_dvo->panel_fixed_mode != NULL) { + if (fixed_mode) { struct drm_display_mode *mode; - mode = drm_mode_duplicate(connector->dev, intel_dvo->panel_fixed_mode); + mode = drm_mode_duplicate(connector->dev, fixed_mode); if (mode) { drm_mode_probed_add(connector, mode); return 1; @@ -383,11 +339,12 @@ static int intel_dvo_get_modes(struct drm_connector *connector) static void intel_dvo_destroy(struct drm_connector *connector) { drm_connector_cleanup(connector); + intel_panel_fini(&to_intel_connector(connector)->panel); kfree(connector); } static const struct drm_connector_funcs intel_dvo_connector_funcs = { - .dpms = intel_dvo_dpms, + .dpms = drm_atomic_helper_connector_dpms, .detect = intel_dvo_detect, .destroy = intel_dvo_destroy, .fill_modes = drm_helper_probe_single_connector_modes, @@ -409,8 +366,6 @@ static void intel_dvo_enc_destroy(struct drm_encoder *encoder) if (intel_dvo->dev.dev_ops->destroy) intel_dvo->dev.dev_ops->destroy(&intel_dvo->dev); - kfree(intel_dvo->panel_fixed_mode); - intel_encoder_destroy(encoder); } @@ -475,6 +430,8 @@ void intel_dvo_init(struct drm_device *dev) return; } + intel_dvo->attached_connector = intel_connector; + intel_encoder = &intel_dvo->base; drm_encoder_init(dev, &intel_encoder->base, &intel_dvo_enc_funcs, encoder_type); @@ -495,17 +452,19 @@ void intel_dvo_init(struct drm_device *dev) struct i2c_adapter *i2c; int gpio; bool dvoinit; + enum pipe pipe; + uint32_t dpll[I915_MAX_PIPES]; /* Allow the I2C driver info to specify the GPIO to be used in * special cases, but otherwise default to what's defined * in the spec. */ - if (intel_gmbus_is_port_valid(dvo->gpio)) + if (intel_gmbus_is_valid_pin(dev_priv, dvo->gpio)) gpio = dvo->gpio; else if (dvo->type == INTEL_DVO_CHIP_LVDS) - gpio = GMBUS_PORT_SSC; + gpio = GMBUS_PIN_SSC; else - gpio = GMBUS_PORT_DPB; + gpio = GMBUS_PIN_DPB; /* Set up the I2C bus necessary for the chip we're probing. * It appears that everything is on GPIOE except for panels @@ -520,8 +479,23 @@ void intel_dvo_init(struct drm_device *dev) */ intel_gmbus_force_bit(i2c, true); + /* ns2501 requires the DVO 2x clock before it will + * respond to i2c accesses, so make sure we have + * have the clock enabled before we attempt to + * initialize the device. + */ + for_each_pipe(dev_priv, pipe) { + dpll[pipe] = I915_READ(DPLL(pipe)); + I915_WRITE(DPLL(pipe), dpll[pipe] | DPLL_DVO_2X_MODE); + } + dvoinit = dvo->dev_ops->init(&intel_dvo->dev, i2c); + /* restore the DVO 2x clock state to original */ + for_each_pipe(dev_priv, pipe) { + I915_WRITE(DPLL(pipe), dpll[pipe]); + } + intel_gmbus_force_bit(i2c, false); if (!dvoinit) @@ -562,8 +536,9 @@ void intel_dvo_init(struct drm_device *dev) * headers, likely), so for now, just get the current * mode being output through DVO. */ - intel_dvo->panel_fixed_mode = - intel_dvo_get_current_mode(connector); + intel_panel_init(&intel_connector->panel, + intel_dvo_get_current_mode(connector), + NULL); intel_dvo->panel_wants_dither = true; } |