diff options
Diffstat (limited to 'kernel/drivers/ata/pata_oldpiix.c')
| -rw-r--r-- | kernel/drivers/ata/pata_oldpiix.c | 273 |
1 files changed, 273 insertions, 0 deletions
diff --git a/kernel/drivers/ata/pata_oldpiix.c b/kernel/drivers/ata/pata_oldpiix.c new file mode 100644 index 000000000..b9bf78b7d --- /dev/null +++ b/kernel/drivers/ata/pata_oldpiix.c @@ -0,0 +1,273 @@ +/* + * pata_oldpiix.c - Intel PATA/SATA controllers + * + * (C) 2005 Red Hat + * + * Some parts based on ata_piix.c by Jeff Garzik and others. + * + * Early PIIX differs significantly from the later PIIX as it lacks + * SITRE and the slave timing registers. This means that you have to + * set timing per channel, or be clever. Libata tells us whenever it + * does drive selection and we use this to reload the timings. + * + * Because of these behaviour differences PIIX gets its own driver module. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_oldpiix" +#define DRV_VERSION "0.5.5" + +/** + * oldpiix_pre_reset - probe begin + * @link: ATA link + * @deadline: deadline jiffies for the operation + * + * Set up cable type and use generic probe init + */ + +static int oldpiix_pre_reset(struct ata_link *link, unsigned long deadline) +{ + struct ata_port *ap = link->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static const struct pci_bits oldpiix_enable_bits[] = { + { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ + { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */ + }; + + if (!pci_test_config_bits(pdev, &oldpiix_enable_bits[ap->port_no])) + return -ENOENT; + + return ata_sff_prereset(link, deadline); +} + +/** + * oldpiix_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device whose timings we are configuring + * + * Set PIO mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *dev = to_pci_dev(ap->host->dev); + unsigned int idetm_port= ap->port_no ? 0x42 : 0x40; + u16 idetm_data; + int control = 0; + + /* + * See Intel Document 298600-004 for the timing programing rules + * for PIIX/ICH. Note that the early PIIX does not have the slave + * timing port at 0x44. + */ + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + if (pio > 1) + control |= 1; /* TIME */ + if (ata_pio_need_iordy(adev)) + control |= 2; /* IE */ + + /* Intel specifies that the prefetch/posting is for disk only */ + if (adev->class == ATA_DEV_ATA) + control |= 4; /* PPE */ + + pci_read_config_word(dev, idetm_port, &idetm_data); + + /* + * Set PPE, IE and TIME as appropriate. + * Clear the other drive's timing bits. + */ + if (adev->devno == 0) { + idetm_data &= 0xCCE0; + idetm_data |= control; + } else { + idetm_data &= 0xCC0E; + idetm_data |= (control << 4); + } + idetm_data |= (timings[pio][0] << 12) | + (timings[pio][1] << 8); + pci_write_config_word(dev, idetm_port, idetm_data); + + /* Track which port is configured */ + ap->private_data = adev; +} + +/** + * oldpiix_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set MWDMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void oldpiix_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u8 idetm_port = ap->port_no ? 0x42 : 0x40; + u16 idetm_data; + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + /* + * MWDMA is driven by the PIO timings. We must also enable + * IORDY unconditionally along with TIME1. PPE has already + * been set when the PIO timing was set. + */ + + unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; + unsigned int control; + const unsigned int needed_pio[3] = { + XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 + }; + int pio = needed_pio[mwdma] - XFER_PIO_0; + + pci_read_config_word(dev, idetm_port, &idetm_data); + + control = 3; /* IORDY|TIME0 */ + /* Intel specifies that the PPE functionality is for disk only */ + if (adev->class == ATA_DEV_ATA) + control |= 4; /* PPE enable */ + + /* If the drive MWDMA is faster than it can do PIO then + we must force PIO into PIO0 */ + + if (adev->pio_mode < needed_pio[mwdma]) + /* Enable DMA timing only */ + control |= 8; /* PIO cycles in PIO0 */ + + /* Mask out the relevant control and timing bits we will load. Also + clear the other drive TIME register as a precaution */ + if (adev->devno == 0) { + idetm_data &= 0xCCE0; + idetm_data |= control; + } else { + idetm_data &= 0xCC0E; + idetm_data |= (control << 4); + } + idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); + pci_write_config_word(dev, idetm_port, idetm_data); + + /* Track which port is configured */ + ap->private_data = adev; +} + +/** + * oldpiix_qc_issue - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * necessary. Our logic also clears TIME0/TIME1 for the other device so + * that, even if we get this wrong, cycles to the other device will + * be made PIO0. + */ + +static unsigned int oldpiix_qc_issue(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + + if (adev != ap->private_data) { + oldpiix_set_piomode(ap, adev); + if (ata_dma_enabled(adev)) + oldpiix_set_dmamode(ap, adev); + } + return ata_bmdma_qc_issue(qc); +} + + +static struct scsi_host_template oldpiix_sht = { + ATA_BMDMA_SHT(DRV_NAME), +}; + +static struct ata_port_operations oldpiix_pata_ops = { + .inherits = &ata_bmdma_port_ops, + .qc_issue = oldpiix_qc_issue, + .cable_detect = ata_cable_40wire, + .set_piomode = oldpiix_set_piomode, + .set_dmamode = oldpiix_set_dmamode, + .prereset = oldpiix_pre_reset, +}; + + +/** + * oldpiix_init_one - Register PIIX ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in oldpiix_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. We probe for combined mode (sigh), + * and then hand over control to libata, for it to do the rest. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, + .port_ops = &oldpiix_pata_ops, + }; + const struct ata_port_info *ppi[] = { &info, NULL }; + + ata_print_version_once(&pdev->dev, DRV_VERSION); + + return ata_pci_bmdma_init_one(pdev, ppi, &oldpiix_sht, NULL, 0); +} + +static const struct pci_device_id oldpiix_pci_tbl[] = { + { PCI_VDEVICE(INTEL, 0x1230), }, + + { } /* terminate list */ +}; + +static struct pci_driver oldpiix_pci_driver = { + .name = DRV_NAME, + .id_table = oldpiix_pci_tbl, + .probe = oldpiix_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +module_pci_driver(oldpiix_pci_driver); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for early PIIX series controllers"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, oldpiix_pci_tbl); +MODULE_VERSION(DRV_VERSION); |