summaryrefslogtreecommitdiffstats
path: root/kernel/drivers/ata/pata_cs5520.c
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/drivers/ata/pata_cs5520.c')
-rw-r--r--kernel/drivers/ata/pata_cs5520.c310
1 files changed, 310 insertions, 0 deletions
diff --git a/kernel/drivers/ata/pata_cs5520.c b/kernel/drivers/ata/pata_cs5520.c
new file mode 100644
index 000000000..4cb24070c
--- /dev/null
+++ b/kernel/drivers/ata/pata_cs5520.c
@@ -0,0 +1,310 @@
+/*
+ * IDE tuning and bus mastering support for the CS5510/CS5520
+ * chipsets
+ *
+ * The CS5510/CS5520 are slightly unusual devices. Unlike the
+ * typical IDE controllers they do bus mastering with the drive in
+ * PIO mode and smarter silicon.
+ *
+ * The practical upshot of this is that we must always tune the
+ * drive for the right PIO mode. We must also ignore all the blacklists
+ * and the drive bus mastering DMA information. Also to confuse matters
+ * further we can do DMA on PIO only drives.
+ *
+ * DMA on the 5510 also requires we disable_hlt() during DMA on early
+ * revisions.
+ *
+ * *** This driver is strictly experimental ***
+ *
+ * (c) Copyright Red Hat Inc 2002
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2, or (at your option) any
+ * later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * Documentation:
+ * Not publicly available.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_cs5520"
+#define DRV_VERSION "0.6.6"
+
+struct pio_clocks
+{
+ int address;
+ int assert;
+ int recovery;
+};
+
+static const struct pio_clocks cs5520_pio_clocks[]={
+ {3, 6, 11},
+ {2, 5, 6},
+ {1, 4, 3},
+ {1, 3, 2},
+ {1, 2, 1}
+};
+
+/**
+ * cs5520_set_timings - program PIO timings
+ * @ap: ATA port
+ * @adev: ATA device
+ *
+ * Program the PIO mode timings for the controller according to the pio
+ * clocking table.
+ */
+
+static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int slave = adev->devno;
+
+ pio -= XFER_PIO_0;
+
+ /* Channel command timing */
+ pci_write_config_byte(pdev, 0x62 + ap->port_no,
+ (cs5520_pio_clocks[pio].recovery << 4) |
+ (cs5520_pio_clocks[pio].assert));
+ /* FIXME: should these use address ? */
+ /* Read command timing */
+ pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave,
+ (cs5520_pio_clocks[pio].recovery << 4) |
+ (cs5520_pio_clocks[pio].assert));
+ /* Write command timing */
+ pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave,
+ (cs5520_pio_clocks[pio].recovery << 4) |
+ (cs5520_pio_clocks[pio].assert));
+}
+
+/**
+ * cs5520_set_piomode - program PIO timings
+ * @ap: ATA port
+ * @adev: ATA device
+ *
+ * Program the PIO mode timings for the controller according to the pio
+ * clocking table.
+ */
+
+static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ cs5520_set_timings(ap, adev, adev->pio_mode);
+}
+
+static struct scsi_host_template cs5520_sht = {
+ ATA_BMDMA_SHT(DRV_NAME),
+ .sg_tablesize = LIBATA_DUMB_MAX_PRD,
+};
+
+static struct ata_port_operations cs5520_port_ops = {
+ .inherits = &ata_bmdma_port_ops,
+ .qc_prep = ata_bmdma_dumb_qc_prep,
+ .cable_detect = ata_cable_40wire,
+ .set_piomode = cs5520_set_piomode,
+};
+
+static int cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+ static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
+ static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
+ struct ata_port_info pi = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .port_ops = &cs5520_port_ops,
+ };
+ const struct ata_port_info *ppi[2];
+ u8 pcicfg;
+ void __iomem *iomap[5];
+ struct ata_host *host;
+ struct ata_ioports *ioaddr;
+ int i, rc;
+
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ /* IDE port enable bits */
+ pci_read_config_byte(pdev, 0x60, &pcicfg);
+
+ /* Check if the ATA ports are enabled */
+ if ((pcicfg & 3) == 0)
+ return -ENODEV;
+
+ ppi[0] = ppi[1] = &ata_dummy_port_info;
+ if (pcicfg & 1)
+ ppi[0] = &pi;
+ if (pcicfg & 2)
+ ppi[1] = &pi;
+
+ if ((pcicfg & 0x40) == 0) {
+ dev_warn(&pdev->dev, "DMA mode disabled. Enabling.\n");
+ pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
+ }
+
+ pi.mwdma_mask = id->driver_data;
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
+ if (!host)
+ return -ENOMEM;
+
+ /* Perform set up for DMA */
+ if (pci_enable_device_io(pdev)) {
+ printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
+ return -ENODEV;
+ }
+
+ if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(32))) {
+ printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
+ return -ENODEV;
+ }
+ if (dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32))) {
+ printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
+ return -ENODEV;
+ }
+
+ /* Map IO ports and initialize host accordingly */
+ iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
+ iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
+ iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
+ iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
+ iomap[4] = pcim_iomap(pdev, 2, 0);
+
+ if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
+ return -ENOMEM;
+
+ ioaddr = &host->ports[0]->ioaddr;
+ ioaddr->cmd_addr = iomap[0];
+ ioaddr->ctl_addr = iomap[1];
+ ioaddr->altstatus_addr = iomap[1];
+ ioaddr->bmdma_addr = iomap[4];
+ ata_sff_std_ports(ioaddr);
+
+ ata_port_desc(host->ports[0],
+ "cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
+ ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
+
+ ioaddr = &host->ports[1]->ioaddr;
+ ioaddr->cmd_addr = iomap[2];
+ ioaddr->ctl_addr = iomap[3];
+ ioaddr->altstatus_addr = iomap[3];
+ ioaddr->bmdma_addr = iomap[4] + 8;
+ ata_sff_std_ports(ioaddr);
+
+ ata_port_desc(host->ports[1],
+ "cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
+ ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
+
+ /* activate the host */
+ pci_set_master(pdev);
+ rc = ata_host_start(host);
+ if (rc)
+ return rc;
+
+ for (i = 0; i < 2; i++) {
+ static const int irq[] = { 14, 15 };
+ struct ata_port *ap = host->ports[i];
+
+ if (ata_port_is_dummy(ap))
+ continue;
+
+ rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
+ ata_bmdma_interrupt, 0, DRV_NAME, host);
+ if (rc)
+ return rc;
+
+ ata_port_desc(ap, "irq %d", irq[i]);
+ }
+
+ return ata_host_register(host, &cs5520_sht);
+}
+
+#ifdef CONFIG_PM_SLEEP
+/**
+ * cs5520_reinit_one - device resume
+ * @pdev: PCI device
+ *
+ * Do any reconfiguration work needed by a resume from RAM. We need
+ * to restore DMA mode support on BIOSen which disabled it
+ */
+
+static int cs5520_reinit_one(struct pci_dev *pdev)
+{
+ struct ata_host *host = pci_get_drvdata(pdev);
+ u8 pcicfg;
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+
+ pci_read_config_byte(pdev, 0x60, &pcicfg);
+ if ((pcicfg & 0x40) == 0)
+ pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
+
+ ata_host_resume(host);
+ return 0;
+}
+
+/**
+ * cs5520_pci_device_suspend - device suspend
+ * @pdev: PCI device
+ *
+ * We have to cut and waste bits from the standard method because
+ * the 5520 is a bit odd and not just a pure ATA device. As a result
+ * we must not disable it. The needed code is short and this avoids
+ * chip specific mess in the core code.
+ */
+
+static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
+{
+ struct ata_host *host = pci_get_drvdata(pdev);
+ int rc = 0;
+
+ rc = ata_host_suspend(host, mesg);
+ if (rc)
+ return rc;
+
+ pci_save_state(pdev);
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+/* For now keep DMA off. We can set it for all but A rev CS5510 once the
+ core ATA code can handle it */
+
+static const struct pci_device_id pata_cs5520[] = {
+ { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
+ { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
+
+ { },
+};
+
+static struct pci_driver cs5520_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = pata_cs5520,
+ .probe = cs5520_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+ .suspend = cs5520_pci_device_suspend,
+ .resume = cs5520_reinit_one,
+#endif
+};
+
+module_pci_driver(cs5520_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, pata_cs5520);
+MODULE_VERSION(DRV_VERSION);