diff options
Diffstat (limited to 'kernel/arch/mn10300/unit-asb2364/unit-init.c')
| -rw-r--r-- | kernel/arch/mn10300/unit-asb2364/unit-init.c | 132 |
1 files changed, 132 insertions, 0 deletions
diff --git a/kernel/arch/mn10300/unit-asb2364/unit-init.c b/kernel/arch/mn10300/unit-asb2364/unit-init.c new file mode 100644 index 000000000..6359b41ce --- /dev/null +++ b/kernel/arch/mn10300/unit-asb2364/unit-init.c @@ -0,0 +1,132 @@ +/* ASB2364 initialisation + * + * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved. + * Written by David Howells (dhowells@redhat.com) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/param.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/delay.h> + +#include <asm/io.h> +#include <asm/setup.h> +#include <asm/processor.h> +#include <asm/irq.h> +#include <asm/intctl-regs.h> +#include <asm/serial-regs.h> +#include <unit/fpga-regs.h> +#include <unit/serial.h> +#include <unit/smsc911x.h> + +#define TTYS0_SERIAL_IER __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_IER * 2, u8) +#define LAN_IRQ_CFG __SYSREG(SMSC911X_BASE + 0x54, u32) +#define LAN_INT_EN __SYSREG(SMSC911X_BASE + 0x5c, u32) + +/* + * initialise some of the unit hardware before gdbstub is set up + */ +asmlinkage void __init unit_init(void) +{ + /* Make sure we aren't going to get unexpected interrupts */ + TTYS0_SERIAL_IER = 0; + SC0RXICR = 0; + SC0TXICR = 0; + SC1RXICR = 0; + SC1TXICR = 0; + SC2RXICR = 0; + SC2TXICR = 0; + + /* Attempt to reset the FPGA attached peripherals */ + ASB2364_FPGA_REG_RESET_LAN = 0x0000; + SyncExBus(); + ASB2364_FPGA_REG_RESET_UART = 0x0000; + SyncExBus(); + ASB2364_FPGA_REG_RESET_I2C = 0x0000; + SyncExBus(); + ASB2364_FPGA_REG_RESET_USB = 0x0000; + SyncExBus(); + ASB2364_FPGA_REG_RESET_AV = 0x0000; + SyncExBus(); + + /* set up the external interrupts */ + + /* XIRQ[0]: NAND RXBY */ + /* SET_XIRQ_TRIGGER(0, XIRQ_TRIGGER_LOWLEVEL); */ + + /* XIRQ[1]: LAN, UART, I2C, USB, PCI, FPGA */ + SET_XIRQ_TRIGGER(1, XIRQ_TRIGGER_LOWLEVEL); + + /* XIRQ[2]: Extend Slot 1-9 */ + /* SET_XIRQ_TRIGGER(2, XIRQ_TRIGGER_LOWLEVEL); */ + +#if defined(CONFIG_EXT_SERIAL_IRQ_LEVEL) && \ + defined(CONFIG_ETHERNET_IRQ_LEVEL) && \ + (CONFIG_EXT_SERIAL_IRQ_LEVEL != CONFIG_ETHERNET_IRQ_LEVEL) +# error CONFIG_EXT_SERIAL_IRQ_LEVEL != CONFIG_ETHERNET_IRQ_LEVEL +#endif + +#if defined(CONFIG_EXT_SERIAL_IRQ_LEVEL) + set_intr_level(XIRQ1, NUM2GxICR_LEVEL(CONFIG_EXT_SERIAL_IRQ_LEVEL)); +#elif defined(CONFIG_ETHERNET_IRQ_LEVEL) + set_intr_level(XIRQ1, NUM2GxICR_LEVEL(CONFIG_ETHERNET_IRQ_LEVEL)); +#endif +} + +/* + * initialise the rest of the unit hardware after gdbstub is ready + */ +asmlinkage void __init unit_setup(void) +{ + /* Release the reset on the SMSC911X so that it is ready by the time we + * need it */ + ASB2364_FPGA_REG_RESET_LAN = 0x0001; + SyncExBus(); + ASB2364_FPGA_REG_RESET_UART = 0x0001; + SyncExBus(); + ASB2364_FPGA_REG_RESET_I2C = 0x0001; + SyncExBus(); + ASB2364_FPGA_REG_RESET_USB = 0x0001; + SyncExBus(); + ASB2364_FPGA_REG_RESET_AV = 0x0001; + SyncExBus(); + + /* Make sure the ethernet chipset isn't going to give us an interrupt + * storm from stuff it was doing pre-reset */ + LAN_IRQ_CFG = 0; + LAN_INT_EN = 0; +} + +/* + * initialise the external interrupts used by a unit of this type + */ +void __init unit_init_IRQ(void) +{ + unsigned int extnum; + + for (extnum = 0 ; extnum < NR_XIRQS ; extnum++) { + switch (GET_XIRQ_TRIGGER(extnum)) { + /* LEVEL triggered interrupts should be made + * post-ACK'able as they hold their lines until + * serviced + */ + case XIRQ_TRIGGER_HILEVEL: + case XIRQ_TRIGGER_LOWLEVEL: + mn10300_set_lateack_irq_type(XIRQ2IRQ(extnum)); + break; + default: + break; + } + } + +#define IRQCTL __SYSREG(0xd5000090, u32) + IRQCTL |= 0x02; + + irq_fpga_init(); +} |