summaryrefslogtreecommitdiffstats
path: root/kernel/arch/cris/arch-v32/mach-fs/dram_init.S
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/arch/cris/arch-v32/mach-fs/dram_init.S')
-rw-r--r--kernel/arch/cris/arch-v32/mach-fs/dram_init.S116
1 files changed, 116 insertions, 0 deletions
diff --git a/kernel/arch/cris/arch-v32/mach-fs/dram_init.S b/kernel/arch/cris/arch-v32/mach-fs/dram_init.S
new file mode 100644
index 000000000..6fbad3365
--- /dev/null
+++ b/kernel/arch/cris/arch-v32/mach-fs/dram_init.S
@@ -0,0 +1,116 @@
+/*
+ * DRAM/SDRAM initialization - alter with care
+ * This file is intended to be included from other assembler files
+ *
+ * Note: This file may not modify r8 or r9 because they are used to
+ * carry information from the decompresser to the kernel
+ *
+ * Copyright (C) 2000-2007 Axis Communications AB
+ *
+ * Authors: Mikael Starvik <starvik@axis.com>
+ */
+
+/* Just to be certain the config file is included, we include it here
+ * explicitely instead of depending on it being included in the file that
+ * uses this code.
+ */
+
+#include <hwregs/asm/reg_map_asm.h>
+#include <hwregs/asm/bif_core_defs_asm.h>
+
+ ;; WARNING! The registers r8 and r9 are used as parameters carrying
+ ;; information from the decompressor (if the kernel was compressed).
+ ;; They should not be used in the code below.
+
+ ; Refer to BIF MDS for a description of SDRAM initialization
+
+ ; Bank configuration
+ move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_cfg_grp0), $r0
+ move.d CONFIG_ETRAX_SDRAM_GRP0_CONFIG, $r1
+ move.d $r1, [$r0]
+ move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_cfg_grp1), $r0
+ move.d CONFIG_ETRAX_SDRAM_GRP1_CONFIG, $r1
+ move.d $r1, [$r0]
+
+ ; Calculate value of mrs_data
+ ; CAS latency = 2 && bus_width = 32 => 0x40
+ ; CAS latency = 3 && bus_width = 32 => 0x60
+ ; CAS latency = 2 && bus_width = 16 => 0x20
+ ; CAS latency = 3 && bus_width = 16 => 0x30
+
+ ; Check if value is already supplied in kernel config
+ move.d CONFIG_ETRAX_SDRAM_COMMAND, $r2
+ bne _set_timing
+ nop
+
+ move.d 0x40, $r4 ; Assume 32 bits and CAS latency = 2
+ move.d CONFIG_ETRAX_SDRAM_TIMING, $r1
+ and.d 0x07, $r1 ; Get CAS latency
+ cmpq 2, $r1 ; CL = 2 ?
+ beq _bw_check
+ nop
+ move.d 0x60, $r4
+
+_bw_check:
+ ; Assume that group 0 width is equal to group 1. This assumption
+ ; is wrong for a group 1 only hardware (such as the grand old
+ ; StorPoint+).
+ move.d CONFIG_ETRAX_SDRAM_GRP0_CONFIG, $r1
+ and.d 0x200, $r1 ; DRAM width is bit 9
+ beq _set_timing
+ lslq 2, $r4 ; mrs_data starts at bit 2
+ lsrq 1, $r4 ; 16 bits. Shift down value.
+
+ ; Set timing parameters (refresh off to avoid Guinness TR 83)
+_set_timing:
+ move.d CONFIG_ETRAX_SDRAM_TIMING, $r1
+ and.d ~(3 << reg_bif_core_rw_sdram_timing___ref___lsb), $r1
+ move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_timing), $r0
+ move.d $r1, [$r0]
+
+ ; Issue NOP command
+ move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_cmd), $r5
+ moveq regk_bif_core_nop, $r1
+ move.d $r1, [$r5]
+
+ ; Wait 200us
+ move.d 10000, $r2
+1: bne 1b
+ subq 1, $r2
+
+ ; Issue initialization command sequence
+ lapc _sdram_commands_start, $r2
+ lapc _sdram_commands_end, $r3
+1: clear.d $r6
+ move.b [$r2+], $r6 ; Load command
+ or.d $r4, $r6 ; Add calculated mrs
+ move.d $r6, [$r5] ; Write rw_sdram_cmd
+ ; Wait 80 ns between each command
+ move.d 4000, $r7
+2: bne 2b
+ subq 1, $r7
+ cmp.d $r2, $r3 ; Last command?
+ bne 1b
+ nop
+
+ ; Start refresh
+ move.d CONFIG_ETRAX_SDRAM_TIMING, $r1
+ move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_timing), $r0
+ move.d $r1, [$r0]
+
+ ; Initialization finished
+ ba _sdram_commands_end
+ nop
+
+_sdram_commands_start:
+ .byte regk_bif_core_pre ; Precharge
+ .byte regk_bif_core_ref ; refresh
+ .byte regk_bif_core_ref ; refresh
+ .byte regk_bif_core_ref ; refresh
+ .byte regk_bif_core_ref ; refresh
+ .byte regk_bif_core_ref ; refresh
+ .byte regk_bif_core_ref ; refresh
+ .byte regk_bif_core_ref ; refresh
+ .byte regk_bif_core_ref ; refresh
+ .byte regk_bif_core_mrs ; mrs
+_sdram_commands_end: