summaryrefslogtreecommitdiffstats
path: root/kernel/arch/cris/arch-v32/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/arch/cris/arch-v32/Kconfig')
-rw-r--r--kernel/arch/cris/arch-v32/Kconfig299
1 files changed, 299 insertions, 0 deletions
diff --git a/kernel/arch/cris/arch-v32/Kconfig b/kernel/arch/cris/arch-v32/Kconfig
new file mode 100644
index 000000000..21bbd93be
--- /dev/null
+++ b/kernel/arch/cris/arch-v32/Kconfig
@@ -0,0 +1,299 @@
+if ETRAX_ARCH_V32
+
+source arch/cris/arch-v32/mach-fs/Kconfig
+source arch/cris/arch-v32/mach-a3/Kconfig
+
+source drivers/cpufreq/Kconfig
+
+config ETRAX_DRAM_VIRTUAL_BASE
+ hex
+ depends on ETRAX_ARCH_V32
+ default "c0000000"
+
+choice
+ prompt "Nbr of Ethernet LED groups"
+ depends on ETRAX_ARCH_V32
+ default ETRAX_NBR_LED_GRP_ONE
+ help
+ Select how many Ethernet LED groups that can be used. Usually one per Ethernet
+ interface is a good choice.
+
+config ETRAX_NBR_LED_GRP_ZERO
+ bool "Use zero LED groups"
+ help
+ Select this if you do not want any Ethernet LEDs.
+
+config ETRAX_NBR_LED_GRP_ONE
+ bool "Use one LED group"
+ help
+ Select this if you want one Ethernet LED group. This LED group
+ can be used for one or more Ethernet interfaces. However, it is
+ recommended that each Ethernet interface use a dedicated LED group.
+
+config ETRAX_NBR_LED_GRP_TWO
+ bool "Use two LED groups"
+ help
+ Select this if you want two Ethernet LED groups. This is the
+ best choice if you have more than one Ethernet interface and
+ would like to have separate LEDs for the interfaces.
+
+endchoice
+
+config ETRAX_LED_G_NET0
+ string "Ethernet LED group 0 green LED bit"
+ depends on ETRAX_ARCH_V32 && (ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO)
+ default "PA3"
+ help
+ Bit to use for the green LED in Ethernet LED group 0.
+
+config ETRAX_LED_R_NET0
+ string "Ethernet LED group 0 red LED bit"
+ depends on ETRAX_ARCH_V32 && (ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO)
+ default "PA4"
+ help
+ Bit to use for the red LED in Ethernet LED group 0.
+
+config ETRAX_LED_G_NET1
+ string "Ethernet group 1 green LED bit"
+ depends on ETRAX_ARCH_V32 && ETRAX_NBR_LED_GRP_TWO
+ default ""
+ help
+ Bit to use for the green LED in Ethernet LED group 1.
+
+config ETRAX_LED_R_NET1
+ string "Ethernet group 1 red LED bit"
+ depends on ETRAX_ARCH_V32 && ETRAX_NBR_LED_GRP_TWO
+ default ""
+ help
+ Bit to use for the red LED in Ethernet LED group 1.
+
+config ETRAX_V32_LED2G
+ string "Second green LED bit"
+ depends on ETRAX_ARCH_V32
+ default "PA5"
+ help
+ Bit to use for the first green LED (status LED).
+ Most Axis products use bit A5 here.
+
+config ETRAX_V32_LED2R
+ string "Second red LED bit"
+ depends on ETRAX_ARCH_V32
+ default "PA6"
+ help
+ Bit to use for the first red LED (network LED).
+ Most Axis products use bit A6 here.
+
+config ETRAX_V32_LED3G
+ string "Third green LED bit"
+ depends on ETRAX_ARCH_V32
+ default "PA7"
+ help
+ Bit to use for the first green LED (drive/power LED).
+ Most Axis products use bit A7 here.
+
+config ETRAX_V32_LED3R
+ string "Third red LED bit"
+ depends on ETRAX_ARCH_V32
+ default "PA7"
+ help
+ Bit to use for the first red LED (drive/power LED).
+ Most Axis products use bit A7 here.
+
+choice
+ prompt "Kernel GDB port"
+ depends on ETRAX_KGDB
+ default ETRAX_KGDB_PORT0
+ help
+ Choose a serial port for kernel debugging. NOTE: This port should
+ not be enabled under Drivers for built-in interfaces (as it has its
+ own initialization code) and should not be the same as the debug port.
+
+config ETRAX_KGDB_PORT4
+ bool "Serial-4"
+ depends on ETRAX_SERIAL_PORTS = 5
+ help
+ Use serial port 4 for kernel debugging.
+
+endchoice
+
+config ETRAX_MEM_GRP1_CONFIG
+ hex "MEM_GRP1_CONFIG"
+ depends on ETRAX_ARCH_V32
+ default "4044a"
+ help
+ Waitstates for flash. The default value is suitable for the
+ standard flashes used in axis products (120 ns).
+
+config ETRAX_MEM_GRP2_CONFIG
+ hex "MEM_GRP2_CONFIG"
+ depends on ETRAX_ARCH_V32
+ default "0"
+ help
+ Waitstates for SRAM. 0 is a good choice for most Axis products.
+
+config ETRAX_MEM_GRP3_CONFIG
+ hex "MEM_GRP3_CONFIG"
+ depends on ETRAX_ARCH_V32
+ default "0"
+ help
+ Waitstates for CSP0-3. 0 is a good choice for most Axis products.
+ It may need to be changed if external devices such as extra
+ register-mapped LEDs are used.
+
+config ETRAX_MEM_GRP4_CONFIG
+ hex "MEM_GRP4_CONFIG"
+ depends on ETRAX_ARCH_V32
+ default "0"
+ help
+ Waitstates for CSP4-6. 0 is a good choice for most Axis products.
+
+config ETRAX_SDRAM_GRP0_CONFIG
+ hex "SDRAM_GRP0_CONFIG"
+ depends on ETRAX_ARCH_V32
+ default "336"
+ help
+ SDRAM configuration for group 0. The value depends on the
+ hardware configuration. The default value is suitable
+ for 32 MB organized as two 16 bits chips (e.g. Axis
+ part number 18550) connected as one 32 bit device (i.e. in
+ the same group).
+
+config ETRAX_SDRAM_GRP1_CONFIG
+ hex "SDRAM_GRP1_CONFIG"
+ depends on ETRAX_ARCH_V32
+ default "0"
+ help
+ SDRAM configuration for group 1. The default value is 0
+ because group 1 is not used in the default configuration,
+ described in the help for SDRAM_GRP0_CONFIG.
+
+config ETRAX_SDRAM_TIMING
+ hex "SDRAM_TIMING"
+ depends on ETRAX_ARCH_V32
+ default "104a"
+ help
+ SDRAM timing parameters. The default value is ok for
+ most hardwares but large SDRAMs may require a faster
+ refresh (a.k.a 8K refresh). The default value implies
+ 100MHz clock and SDR mode.
+
+config ETRAX_SDRAM_COMMAND
+ hex "SDRAM_COMMAND"
+ depends on ETRAX_ARCH_V32
+ default "0"
+ help
+ SDRAM command. Should be 0 unless you really know what
+ you are doing (may be != 0 for unusual address line
+ mappings such as in a MCM)..
+
+config ETRAX_DEF_GIO_PA_OE
+ hex "GIO_PA_OE"
+ depends on ETRAX_ARCH_V32
+ default "1c"
+ help
+ Configures the direction of general port A bits. 1 is out, 0 is in.
+ This is often totally different depending on the product used.
+ There are some guidelines though - if you know that only LED's are
+ connected to port PA, then they are usually connected to bits 2-4
+ and you can therefore use 1c. On other boards which don't have the
+ LED's at the general ports, these bits are used for all kinds of
+ stuff. If you don't know what to use, it is always safe to put all
+ as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PA_OUT
+ hex "GIO_PA_OUT"
+ depends on ETRAX_ARCH_V32
+ default "00"
+ help
+ Configures the initial data for the general port A bits. Most
+ products should use 00 here.
+
+config ETRAX_DEF_GIO_PB_OE
+ hex "GIO_PB_OE"
+ depends on ETRAX_ARCH_V32
+ default "00000"
+ help
+ Configures the direction of general port B bits. 1 is out, 0 is in.
+ This is often totally different depending on the product used.
+ There are some guidelines though - if you know that only LED's are
+ connected to port PA, then they are usually connected to bits 2-4
+ and you can therefore use 1c. On other boards which don't have the
+ LED's at the general ports, these bits are used for all kinds of
+ stuff. If you don't know what to use, it is always safe to put all
+ as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PB_OUT
+ hex "GIO_PB_OUT"
+ depends on ETRAX_ARCH_V32
+ default "00000"
+ help
+ Configures the initial data for the general port B bits. Most
+ products should use 00000 here.
+
+config ETRAX_DEF_GIO_PC_OE
+ hex "GIO_PC_OE"
+ depends on ETRAX_ARCH_V32
+ default "00000"
+ help
+ Configures the direction of general port C bits. 1 is out, 0 is in.
+ This is often totally different depending on the product used.
+ There are some guidelines though - if you know that only LED's are
+ connected to port PA, then they are usually connected to bits 2-4
+ and you can therefore use 1c. On other boards which don't have the
+ LED's at the general ports, these bits are used for all kinds of
+ stuff. If you don't know what to use, it is always safe to put all
+ as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PC_OUT
+ hex "GIO_PC_OUT"
+ depends on ETRAX_ARCH_V32
+ default "00000"
+ help
+ Configures the initial data for the general port C bits. Most
+ products should use 00000 here.
+
+config ETRAX_DEF_GIO_PD_OE
+ hex "GIO_PD_OE"
+ depends on ETRAX_ARCH_V32
+ default "00000"
+ help
+ Configures the direction of general port D bits. 1 is out, 0 is in.
+ This is often totally different depending on the product used.
+ There are some guidelines though - if you know that only LED's are
+ connected to port PA, then they are usually connected to bits 2-4
+ and you can therefore use 1c. On other boards which don't have the
+ LED's at the general ports, these bits are used for all kinds of
+ stuff. If you don't know what to use, it is always safe to put all
+ as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PD_OUT
+ hex "GIO_PD_OUT"
+ depends on ETRAX_ARCH_V32
+ default "00000"
+ help
+ Configures the initial data for the general port D bits. Most
+ products should use 00000 here.
+
+config ETRAX_DEF_GIO_PE_OE
+ hex "GIO_PE_OE"
+ depends on ETRAX_ARCH_V32
+ default "00000"
+ help
+ Configures the direction of general port E bits. 1 is out, 0 is in.
+ This is often totally different depending on the product used.
+ There are some guidelines though - if you know that only LED's are
+ connected to port PA, then they are usually connected to bits 2-4
+ and you can therefore use 1c. On other boards which don't have the
+ LED's at the general ports, these bits are used for all kinds of
+ stuff. If you don't know what to use, it is always safe to put all
+ as inputs, although floating inputs isn't good.
+
+config ETRAX_DEF_GIO_PE_OUT
+ hex "GIO_PE_OUT"
+ depends on ETRAX_ARCH_V32
+ default "00000"
+ help
+ Configures the initial data for the general port E bits. Most
+ products should use 00000 here.
+
+endif