diff options
Diffstat (limited to 'kernel/arch/cris/arch-v10/kernel/head.S')
-rw-r--r-- | kernel/arch/cris/arch-v10/kernel/head.S | 723 |
1 files changed, 723 insertions, 0 deletions
diff --git a/kernel/arch/cris/arch-v10/kernel/head.S b/kernel/arch/cris/arch-v10/kernel/head.S new file mode 100644 index 000000000..4a146e174 --- /dev/null +++ b/kernel/arch/cris/arch-v10/kernel/head.S @@ -0,0 +1,723 @@ +/* + * Head of the kernel - alter with care + * + * Copyright (C) 2000, 2001, 2010 Axis Communications AB + * + */ + +#define ASSEMBLER_MACROS_ONLY +/* The IO_* macros use the ## token concatenation operator, so + -traditional must not be used when assembling this file. */ +#include <arch/sv_addr_ag.h> + +#define CRAMFS_MAGIC 0x28cd3d45 +#define RAM_INIT_MAGIC 0x56902387 +#define COMMAND_LINE_MAGIC 0x87109563 + +#define START_ETHERNET_CLOCK IO_STATE(R_NETWORK_GEN_CONFIG, enable, on) |\ + IO_STATE(R_NETWORK_GEN_CONFIG, phy, mii_clk) + + ;; exported symbols + + .globl etrax_irv + .globl romfs_start + .globl romfs_length + .globl romfs_in_flash + .globl swapper_pg_dir + + .text + + ;; This is the entry point of the kernel. We are in supervisor mode. + ;; 0x00000000 if Flash, 0x40004000 if DRAM + ;; since etrax actually starts at address 2 when booting from flash, we + ;; put a nop (2 bytes) here first so we dont accidentally skip the di + ;; + ;; NOTICE! The registers r8 and r9 are used as parameters carrying + ;; information from the decompressor (if the kernel was compressed). + ;; They should not be used in the code below until read. + + nop + di + + ;; First setup the kseg_c mapping from where the kernel is linked + ;; to 0x40000000 (where the actual DRAM resides) otherwise + ;; we cannot do very much! See arch/cris/README.mm + ;; + ;; Notice that since we're potentially running at 0x00 or 0x40 right now, + ;; we will get a fault as soon as we enable the MMU if we dont + ;; temporarily map those segments linearily. + ;; + ;; Due to a bug in Etrax-100 LX version 1 we need to map the memory + ;; slightly different. The bug is that you can't remap bit 31 of + ;; an address. Though we can check the version register for + ;; whether the bug is present, some constants would then have to + ;; be variables, so we don't. The drawback is that you can "only" map + ;; 1G per process with CONFIG_CRIS_LOW_MAP. + +#ifdef CONFIG_CRIS_LOW_MAP + ; kseg mappings, temporary map of 0xc0->0x40 + move.d IO_FIELD (R_MMU_KBASE_HI, base_c, 4) \ + | IO_FIELD (R_MMU_KBASE_HI, base_b, 0xb) \ + | IO_FIELD (R_MMU_KBASE_HI, base_9, 9) \ + | IO_FIELD (R_MMU_KBASE_HI, base_8, 8), $r0 + move.d $r0, [R_MMU_KBASE_HI] + + ; temporary map of 0x40->0x40 and 0x60->0x40 + move.d IO_FIELD (R_MMU_KBASE_LO, base_6, 4) \ + | IO_FIELD (R_MMU_KBASE_LO, base_4, 4), $r0 + move.d $r0, [R_MMU_KBASE_LO] + + ; mmu enable, segs e,c,b,a,6,5,4,0 segment mapped + move.d IO_STATE (R_MMU_CONFIG, mmu_enable, enable) \ + | IO_STATE (R_MMU_CONFIG, inv_excp, enable) \ + | IO_STATE (R_MMU_CONFIG, acc_excp, enable) \ + | IO_STATE (R_MMU_CONFIG, we_excp, enable) \ + | IO_STATE (R_MMU_CONFIG, seg_f, page) \ + | IO_STATE (R_MMU_CONFIG, seg_e, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_d, page) \ + | IO_STATE (R_MMU_CONFIG, seg_c, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_b, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_a, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_9, page) \ + | IO_STATE (R_MMU_CONFIG, seg_8, page) \ + | IO_STATE (R_MMU_CONFIG, seg_7, page) \ + | IO_STATE (R_MMU_CONFIG, seg_6, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_5, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_4, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_3, page) \ + | IO_STATE (R_MMU_CONFIG, seg_2, page) \ + | IO_STATE (R_MMU_CONFIG, seg_1, page) \ + | IO_STATE (R_MMU_CONFIG, seg_0, seg), $r0 + move.d $r0, [R_MMU_CONFIG] +#else + ; kseg mappings + move.d IO_FIELD (R_MMU_KBASE_HI, base_e, 8) \ + | IO_FIELD (R_MMU_KBASE_HI, base_c, 4) \ + | IO_FIELD (R_MMU_KBASE_HI, base_b, 0xb), $r0 + move.d $r0, [R_MMU_KBASE_HI] + + ; temporary map of 0x40->0x40 and 0x00->0x00 + move.d IO_FIELD (R_MMU_KBASE_LO, base_4, 4), $r0 + move.d $r0, [R_MMU_KBASE_LO] + + ; mmu enable, segs f,e,c,b,4,0 segment mapped + move.d IO_STATE (R_MMU_CONFIG, mmu_enable, enable) \ + | IO_STATE (R_MMU_CONFIG, inv_excp, enable) \ + | IO_STATE (R_MMU_CONFIG, acc_excp, enable) \ + | IO_STATE (R_MMU_CONFIG, we_excp, enable) \ + | IO_STATE (R_MMU_CONFIG, seg_f, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_e, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_d, page) \ + | IO_STATE (R_MMU_CONFIG, seg_c, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_b, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_a, page) \ + | IO_STATE (R_MMU_CONFIG, seg_9, page) \ + | IO_STATE (R_MMU_CONFIG, seg_8, page) \ + | IO_STATE (R_MMU_CONFIG, seg_7, page) \ + | IO_STATE (R_MMU_CONFIG, seg_6, page) \ + | IO_STATE (R_MMU_CONFIG, seg_5, page) \ + | IO_STATE (R_MMU_CONFIG, seg_4, seg) \ + | IO_STATE (R_MMU_CONFIG, seg_3, page) \ + | IO_STATE (R_MMU_CONFIG, seg_2, page) \ + | IO_STATE (R_MMU_CONFIG, seg_1, page) \ + | IO_STATE (R_MMU_CONFIG, seg_0, seg), $r0 + move.d $r0, [R_MMU_CONFIG] +#endif + + ;; Now we need to sort out the segments and their locations in RAM or + ;; Flash. The image in the Flash (or in DRAM) consists of 3 pieces: + ;; 1) kernel text, 2) kernel data, 3) ROM filesystem image + ;; But the linker has linked the kernel to expect this layout in + ;; DRAM memory: + ;; 1) kernel text, 2) kernel data, 3) kernel BSS + ;; (the location of the ROM filesystem is determined by the krom driver) + ;; If we boot this from Flash, we want to keep the ROM filesystem in + ;; the flash, we want to copy the text and need to copy the data to DRAM. + ;; But if we boot from DRAM, we need to move the ROMFS image + ;; from its position after kernel data, to after kernel BSS, BEFORE the + ;; kernel starts using the BSS area (since its "overlayed" with the ROMFS) + ;; + ;; In both cases, we start in un-cached mode, and need to jump into a + ;; cached PC after we're done fiddling around with the segments. + ;; + ;; arch/etrax100/etrax100.ld sets some symbols that define the start + ;; and end of each segment. + + ;; Check if we start from DRAM or FLASH by testing PC + + move.d $pc,$r0 + and.d 0x7fffffff,$r0 ; get rid of the non-cache bit + cmp.d 0x10000,$r0 ; arbitrary... just something above this code + blo _inflash0 + nop + + jump _inram ; enter cached ram + + ;; Jumpgate for branches. +_inflash0: + jump _inflash + + ;; Put this in a suitable section where we can reclaim storage + ;; after init. + .section ".init.text", "ax" +_inflash: +#ifdef CONFIG_ETRAX_ETHERNET + ;; Start MII clock to make sure it is running when tranceiver is reset + move.d START_ETHERNET_CLOCK, $r0 + move.d $r0, [R_NETWORK_GEN_CONFIG] +#endif + + ;; Set up waitstates etc according to kernel configuration. + move.d CONFIG_ETRAX_DEF_R_WAITSTATES, $r0 + move.d $r0, [R_WAITSTATES] + + move.d CONFIG_ETRAX_DEF_R_BUS_CONFIG, $r0 + move.d $r0, [R_BUS_CONFIG] + + ;; We need to initialze DRAM registers before we start using the DRAM + + cmp.d RAM_INIT_MAGIC, $r8 ; Already initialized? + beq _dram_init_finished + nop + +#include "../lib/dram_init.S" + +_dram_init_finished: + ;; Copy text+data to DRAM + ;; This is fragile - the calculation of r4 as the image size depends + ;; on that the labels below actually are the first and last positions + ;; in the linker-script. + ;; + ;; Then the locating of the cramfs image depends on the aforementioned + ;; image being located in the flash at 0. This is most often not true, + ;; thus the following does not work (normally there is a rescue-block + ;; between the physical start of the flash and the flash-image start, + ;; and when run with compression, the kernel is actually unpacked to + ;; DRAM and we never get here in the first place :)) + + moveq 0, $r0 ; source + move.d text_start, $r1 ; destination + move.d __vmlinux_end, $r2 ; end destination + move.d $r2, $r4 + sub.d $r1, $r4 ; r4=__vmlinux_end in flash, used below +1: move.w [$r0+], $r3 + move.w $r3, [$r1+] + cmp.d $r2, $r1 + blo 1b + nop + + ;; We keep the cramfs in the flash. + ;; There might be none, but that does not matter because + ;; we don't do anything than read some bytes here. + + moveq 0, $r0 + move.d $r0, [romfs_length] ; default if there is no cramfs + + move.d [$r4], $r0 ; cramfs_super.magic + cmp.d CRAMFS_MAGIC, $r0 + bne 1f + nop + move.d [$r4 + 4], $r0 ; cramfs_super.size + move.d $r0, [romfs_length] +#ifdef CONFIG_CRIS_LOW_MAP + add.d 0x50000000, $r4 ; add flash start in virtual memory (cached) +#else + add.d 0xf0000000, $r4 ; add flash start in virtual memory (cached) +#endif + move.d $r4, [romfs_start] +1: + moveq 1, $r0 + move.d $r0, [romfs_in_flash] + + jump _start_it ; enter code, cached this time + +_inram: + ;; Move the ROM fs to after BSS end. This assumes that the cramfs + ;; second longword contains the length of the cramfs + + moveq 0, $r0 + move.d $r0, [romfs_length] ; default if there is no cramfs + + ;; The kernel could have been unpacked to DRAM by the loader, but + ;; the cramfs image could still be in the Flash directly after the + ;; compressed kernel image. The loader passes the address of the + ;; byte succeeding the last compressed byte in the flash in the + ;; register r9 when starting the kernel. Check if r9 points to a + ;; decent cramfs image! + ;; (Notice that if this is not booted from the loader, r9 will be + ;; garbage but we do sanity checks on it, the chance that it points + ;; to a cramfs magic is small.. ) + + cmp.d 0x0ffffff8, $r9 + bhs _no_romfs_in_flash ; r9 points outside the flash area + nop + move.d [$r9], $r0 ; cramfs_super.magic + cmp.d CRAMFS_MAGIC, $r0 + bne _no_romfs_in_flash + nop + move.d [$r9+4], $r0 ; cramfs_super.length + move.d $r0, [romfs_length] +#ifdef CONFIG_CRIS_LOW_MAP + add.d 0x50000000, $r9 ; add flash start in virtual memory (cached) +#else + add.d 0xf0000000, $r9 ; add flash start in virtual memory (cached) +#endif + move.d $r9, [romfs_start] + + moveq 1, $r0 + move.d $r0, [romfs_in_flash] + + jump _start_it ; enter code, cached this time + +_no_romfs_in_flash: + + ;; Check if there is a cramfs (magic value). + ;; Notice that we check for cramfs magic value - which is + ;; the "rom fs" we'll possibly use in 2.4 if not JFFS (which does + ;; not need this mechanism anyway) + + move.d __init_end, $r0; the image will be after the end of init + move.d [$r0], $r1 ; cramfs assumes same endian on host/target + cmp.d CRAMFS_MAGIC, $r1; magic value in cramfs superblock + bne 2f + nop + + ;; Ok. What is its size ? + + move.d [$r0 + 4], $r2 ; cramfs_super.size (again, no need to swapwb) + + ;; We want to copy it to the end of the BSS + + move.d _end, $r1 + + ;; Remember values so cramfs and setup can find this info + + move.d $r1, [romfs_start] ; new romfs location + move.d $r2, [romfs_length] + + ;; We need to copy it backwards, since they can be overlapping + + add.d $r2, $r0 + add.d $r2, $r1 + + ;; Go ahead. Make my loop. + + lsrq 1, $r2 ; size is in bytes, we copy words + +1: move.w [$r0=$r0-2],$r3 + move.w $r3,[$r1=$r1-2] + subq 1, $r2 + bne 1b + nop + +2: + ;; Dont worry that the BSS is tainted. It will be cleared later. + + moveq 0, $r0 + move.d $r0, [romfs_in_flash] + + jump _start_it ; better skip the additional cramfs check below + +_start_it: + + ;; Check if kernel command line is supplied + cmp.d COMMAND_LINE_MAGIC, $r10 + bne no_command_line + nop + + move.d 256, $r13 + move.d cris_command_line, $r10 + or.d 0x80000000, $r11 ; Make it virtual +1: + move.b [$r11+], $r12 + move.b $r12, [$r10+] + subq 1, $r13 + bne 1b + nop + +no_command_line: + + ;; the kernel stack is overlayed with the task structure for each + ;; task. thus the initial kernel stack is in the same page as the + ;; init_task (but starts in the top of the page, size 8192) + move.d init_thread_union + 8192, $sp + move.d ibr_start,$r0 ; this symbol is set by the linker script + move $r0,$ibr + move.d $r0,[etrax_irv] ; set the interrupt base register and pointer + + ;; Clear BSS region, from _bss_start to _end + + move.d __bss_start, $r0 + move.d _end, $r1 +1: clear.d [$r0+] + cmp.d $r1, $r0 + blo 1b + nop + +#ifdef CONFIG_BLK_DEV_ETRAXIDE + ;; disable ATA before enabling it in genconfig below + moveq 0,$r0 + move.d $r0,[R_ATA_CTRL_DATA] + move.d $r0,[R_ATA_TRANSFER_CNT] + move.d $r0,[R_ATA_CONFIG] +#if 0 + move.d R_PORT_G_DATA, $r1 + move.d $r0, [$r1]; assert ATA bus-reset + nop + nop + nop + nop + nop + nop + move.d 0x08000000,$r0 + move.d $r0,[$r1] +#endif +#endif + +#ifdef CONFIG_JULIETTE + ;; configure external DMA channel 0 before enabling it in genconfig + + moveq 0,$r0 + move.d $r0,[R_EXT_DMA_0_ADDR] + ; cnt enable, word size, output, stop, size 0 + move.d IO_STATE (R_EXT_DMA_0_CMD, cnt, enable) \ + | IO_STATE (R_EXT_DMA_0_CMD, rqpol, ahigh) \ + | IO_STATE (R_EXT_DMA_0_CMD, apol, ahigh) \ + | IO_STATE (R_EXT_DMA_0_CMD, rq_ack, burst) \ + | IO_STATE (R_EXT_DMA_0_CMD, wid, word) \ + | IO_STATE (R_EXT_DMA_0_CMD, dir, output) \ + | IO_STATE (R_EXT_DMA_0_CMD, run, stop) \ + | IO_FIELD (R_EXT_DMA_0_CMD, trf_count, 0),$r0 + move.d $r0,[R_EXT_DMA_0_CMD] + + ;; reset dma4 and wait for completion + + moveq IO_STATE (R_DMA_CH4_CMD, cmd, reset),$r0 + move.b $r0,[R_DMA_CH4_CMD] +1: move.b [R_DMA_CH4_CMD],$r0 + and.b IO_MASK (R_DMA_CH4_CMD, cmd),$r0 + cmp.b IO_STATE (R_DMA_CH4_CMD, cmd, reset),$r0 + beq 1b + nop + + ;; reset dma5 and wait for completion + + moveq IO_STATE (R_DMA_CH5_CMD, cmd, reset),$r0 + move.b $r0,[R_DMA_CH5_CMD] +1: move.b [R_DMA_CH5_CMD],$r0 + and.b IO_MASK (R_DMA_CH5_CMD, cmd),$r0 + cmp.b IO_STATE (R_DMA_CH5_CMD, cmd, reset),$r0 + beq 1b + nop +#endif + + ;; Etrax product HW genconfig setup + + moveq 0,$r0 + + ;; Select or disable serial port 2 +#ifdef CONFIG_ETRAX_SERIAL_PORT2 + or.d IO_STATE (R_GEN_CONFIG, ser2, select),$r0 +#else + or.d IO_STATE (R_GEN_CONFIG, ser2, disable),$r0 +#endif + + ;; Init interfaces (disable them). + or.d IO_STATE (R_GEN_CONFIG, scsi0, disable) \ + | IO_STATE (R_GEN_CONFIG, ata, disable) \ + | IO_STATE (R_GEN_CONFIG, par0, disable) \ + | IO_STATE (R_GEN_CONFIG, mio, disable) \ + | IO_STATE (R_GEN_CONFIG, scsi1, disable) \ + | IO_STATE (R_GEN_CONFIG, scsi0w, disable) \ + | IO_STATE (R_GEN_CONFIG, par1, disable) \ + | IO_STATE (R_GEN_CONFIG, ser3, disable) \ + | IO_STATE (R_GEN_CONFIG, mio_w, disable) \ + | IO_STATE (R_GEN_CONFIG, usb1, disable) \ + | IO_STATE (R_GEN_CONFIG, usb2, disable) \ + | IO_STATE (R_GEN_CONFIG, par_w, disable),$r0 + + ;; Init DMA channel muxing (set to unused clients). + or.d IO_STATE (R_GEN_CONFIG, dma2, ata) \ + | IO_STATE (R_GEN_CONFIG, dma3, ata) \ + | IO_STATE (R_GEN_CONFIG, dma4, scsi1) \ + | IO_STATE (R_GEN_CONFIG, dma5, scsi1) \ + | IO_STATE (R_GEN_CONFIG, dma6, unused) \ + | IO_STATE (R_GEN_CONFIG, dma7, unused) \ + | IO_STATE (R_GEN_CONFIG, dma8, usb) \ + | IO_STATE (R_GEN_CONFIG, dma9, usb),$r0 + + +#if defined(CONFIG_ETRAX_DEF_R_PORT_G0_DIR_OUT) + or.d IO_STATE (R_GEN_CONFIG, g0dir, out),$r0 +#endif + +#if defined(CONFIG_ETRAX_DEF_R_PORT_G8_15_DIR_OUT) + or.d IO_STATE (R_GEN_CONFIG, g8_15dir, out),$r0 +#endif +#if defined(CONFIG_ETRAX_DEF_R_PORT_G16_23_DIR_OUT) + or.d IO_STATE (R_GEN_CONFIG, g16_23dir, out),$r0 +#endif + +#if defined(CONFIG_ETRAX_DEF_R_PORT_G24_DIR_OUT) + or.d IO_STATE (R_GEN_CONFIG, g24dir, out),$r0 +#endif + + move.d $r0,[genconfig_shadow] ; init a shadow register of R_GEN_CONFIG + + move.d $r0,[R_GEN_CONFIG] + +#if 0 + moveq 4,$r0 + move.b $r0,[R_DMA_CH6_CMD] ; reset (ser0 dma out) + move.b $r0,[R_DMA_CH7_CMD] ; reset (ser0 dma in) +1: move.b [R_DMA_CH6_CMD],$r0 ; wait for reset cycle to finish + and.b 7,$r0 + cmp.b 4,$r0 + beq 1b + nop +1: move.b [R_DMA_CH7_CMD],$r0 ; wait for reset cycle to finish + and.b 7,$r0 + cmp.b 4,$r0 + beq 1b + nop +#endif + + moveq IO_STATE (R_DMA_CH8_CMD, cmd, reset),$r0 + move.b $r0,[R_DMA_CH8_CMD] ; reset (ser1 dma out) + move.b $r0,[R_DMA_CH9_CMD] ; reset (ser1 dma in) +1: move.b [R_DMA_CH8_CMD],$r0 ; wait for reset cycle to finish + andq IO_MASK (R_DMA_CH8_CMD, cmd),$r0 + cmpq IO_STATE (R_DMA_CH8_CMD, cmd, reset),$r0 + beq 1b + nop +1: move.b [R_DMA_CH9_CMD],$r0 ; wait for reset cycle to finish + andq IO_MASK (R_DMA_CH9_CMD, cmd),$r0 + cmpq IO_STATE (R_DMA_CH9_CMD, cmd, reset),$r0 + beq 1b + nop + + ;; setup port PA and PB default initial directions and data + ;; including their shadow registers + + move.b CONFIG_ETRAX_DEF_R_PORT_PA_DIR,$r0 +#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PA7) + or.b IO_STATE (R_PORT_PA_DIR, dir7, output),$r0 +#endif + move.b $r0,[port_pa_dir_shadow] + move.b $r0,[R_PORT_PA_DIR] + move.b CONFIG_ETRAX_DEF_R_PORT_PA_DATA,$r0 +#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PA7) +#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH) + and.b ~(1 << 7),$r0 +#else + or.b (1 << 7),$r0 +#endif +#endif + move.b $r0,[port_pa_data_shadow] + move.b $r0,[R_PORT_PA_DATA] + + move.b CONFIG_ETRAX_DEF_R_PORT_PB_CONFIG,$r0 + move.b $r0,[port_pb_config_shadow] + move.b $r0,[R_PORT_PB_CONFIG] + move.b CONFIG_ETRAX_DEF_R_PORT_PB_DIR,$r0 +#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PB5) + or.b IO_STATE (R_PORT_PB_DIR, dir5, output),$r0 +#endif + move.b $r0,[port_pb_dir_shadow] + move.b $r0,[R_PORT_PB_DIR] + move.b CONFIG_ETRAX_DEF_R_PORT_PB_DATA,$r0 +#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PB5) +#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH) + and.b ~(1 << 5),$r0 +#else + or.b (1 << 5),$r0 +#endif +#endif + move.b $r0,[port_pb_data_shadow] + move.b $r0,[R_PORT_PB_DATA] + + moveq 0, $r0 + move.d $r0,[port_pb_i2c_shadow] + move.d $r0, [R_PORT_PB_I2C] + + moveq 0,$r0 +#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_G10) +#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH) + and.d ~(1 << 10),$r0 +#else + or.d (1 << 10),$r0 +#endif +#endif +#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_G11) +#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH) + and.d ~(1 << 11),$r0 +#else + or.d (1 << 11),$r0 +#endif +#endif + move.d $r0,[port_g_data_shadow] + move.d $r0,[R_PORT_G_DATA] + + ;; setup the serial port 0 at 115200 baud for debug purposes + + moveq IO_STATE (R_SERIAL0_XOFF, tx_stop, enable) \ + | IO_STATE (R_SERIAL0_XOFF, auto_xoff, disable) \ + | IO_FIELD (R_SERIAL0_XOFF, xoff_char, 0),$r0 + move.d $r0,[R_SERIAL0_XOFF] + + ; 115.2kbaud for both transmit and receive + move.b IO_STATE (R_SERIAL0_BAUD, tr_baud, c115k2Hz) \ + | IO_STATE (R_SERIAL0_BAUD, rec_baud, c115k2Hz),$r0 + move.b $r0,[R_SERIAL0_BAUD] + + ; Set up and enable the serial0 receiver. + move.b IO_STATE (R_SERIAL0_REC_CTRL, dma_err, stop) \ + | IO_STATE (R_SERIAL0_REC_CTRL, rec_enable, enable) \ + | IO_STATE (R_SERIAL0_REC_CTRL, rts_, active) \ + | IO_STATE (R_SERIAL0_REC_CTRL, sampling, middle) \ + | IO_STATE (R_SERIAL0_REC_CTRL, rec_stick_par, normal) \ + | IO_STATE (R_SERIAL0_REC_CTRL, rec_par, even) \ + | IO_STATE (R_SERIAL0_REC_CTRL, rec_par_en, disable) \ + | IO_STATE (R_SERIAL0_REC_CTRL, rec_bitnr, rec_8bit),$r0 + move.b $r0,[R_SERIAL0_REC_CTRL] + + ; Set up and enable the serial0 transmitter. + move.b IO_FIELD (R_SERIAL0_TR_CTRL, txd, 0) \ + | IO_STATE (R_SERIAL0_TR_CTRL, tr_enable, enable) \ + | IO_STATE (R_SERIAL0_TR_CTRL, auto_cts, disabled) \ + | IO_STATE (R_SERIAL0_TR_CTRL, stop_bits, one_bit) \ + | IO_STATE (R_SERIAL0_TR_CTRL, tr_stick_par, normal) \ + | IO_STATE (R_SERIAL0_TR_CTRL, tr_par, even) \ + | IO_STATE (R_SERIAL0_TR_CTRL, tr_par_en, disable) \ + | IO_STATE (R_SERIAL0_TR_CTRL, tr_bitnr, tr_8bit),$r0 + move.b $r0,[R_SERIAL0_TR_CTRL] + + ;; setup the serial port 1 at 115200 baud for debug purposes + + moveq IO_STATE (R_SERIAL1_XOFF, tx_stop, enable) \ + | IO_STATE (R_SERIAL1_XOFF, auto_xoff, disable) \ + | IO_FIELD (R_SERIAL1_XOFF, xoff_char, 0),$r0 + move.d $r0,[R_SERIAL1_XOFF] + + ; 115.2kbaud for both transmit and receive + move.b IO_STATE (R_SERIAL1_BAUD, tr_baud, c115k2Hz) \ + | IO_STATE (R_SERIAL1_BAUD, rec_baud, c115k2Hz),$r0 + move.b $r0,[R_SERIAL1_BAUD] + + ; Set up and enable the serial1 receiver. + move.b IO_STATE (R_SERIAL1_REC_CTRL, dma_err, stop) \ + | IO_STATE (R_SERIAL1_REC_CTRL, rec_enable, enable) \ + | IO_STATE (R_SERIAL1_REC_CTRL, rts_, active) \ + | IO_STATE (R_SERIAL1_REC_CTRL, sampling, middle) \ + | IO_STATE (R_SERIAL1_REC_CTRL, rec_stick_par, normal) \ + | IO_STATE (R_SERIAL1_REC_CTRL, rec_par, even) \ + | IO_STATE (R_SERIAL1_REC_CTRL, rec_par_en, disable) \ + | IO_STATE (R_SERIAL1_REC_CTRL, rec_bitnr, rec_8bit),$r0 + move.b $r0,[R_SERIAL1_REC_CTRL] + + ; Set up and enable the serial1 transmitter. + move.b IO_FIELD (R_SERIAL1_TR_CTRL, txd, 0) \ + | IO_STATE (R_SERIAL1_TR_CTRL, tr_enable, enable) \ + | IO_STATE (R_SERIAL1_TR_CTRL, auto_cts, disabled) \ + | IO_STATE (R_SERIAL1_TR_CTRL, stop_bits, one_bit) \ + | IO_STATE (R_SERIAL1_TR_CTRL, tr_stick_par, normal) \ + | IO_STATE (R_SERIAL1_TR_CTRL, tr_par, even) \ + | IO_STATE (R_SERIAL1_TR_CTRL, tr_par_en, disable) \ + | IO_STATE (R_SERIAL1_TR_CTRL, tr_bitnr, tr_8bit),$r0 + move.b $r0,[R_SERIAL1_TR_CTRL] + +#ifdef CONFIG_ETRAX_SERIAL_PORT2 + ;; setup the serial port 2 at 115200 baud for debug purposes + + moveq IO_STATE (R_SERIAL2_XOFF, tx_stop, enable) \ + | IO_STATE (R_SERIAL2_XOFF, auto_xoff, disable) \ + | IO_FIELD (R_SERIAL2_XOFF, xoff_char, 0),$r0 + move.d $r0,[R_SERIAL2_XOFF] + + ; 115.2kbaud for both transmit and receive + move.b IO_STATE (R_SERIAL2_BAUD, tr_baud, c115k2Hz) \ + | IO_STATE (R_SERIAL2_BAUD, rec_baud, c115k2Hz),$r0 + move.b $r0,[R_SERIAL2_BAUD] + + ; Set up and enable the serial2 receiver. + move.b IO_STATE (R_SERIAL2_REC_CTRL, dma_err, stop) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_enable, enable) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rts_, active) \ + | IO_STATE (R_SERIAL2_REC_CTRL, sampling, middle) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_stick_par, normal) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_par, even) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_par_en, disable) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_bitnr, rec_8bit),$r0 + move.b $r0,[R_SERIAL2_REC_CTRL] + + ; Set up and enable the serial2 transmitter. + move.b IO_FIELD (R_SERIAL2_TR_CTRL, txd, 0) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_enable, enable) \ + | IO_STATE (R_SERIAL2_TR_CTRL, auto_cts, disabled) \ + | IO_STATE (R_SERIAL2_TR_CTRL, stop_bits, one_bit) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_stick_par, normal) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_par, even) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_par_en, disable) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_bitnr, tr_8bit),$r0 + move.b $r0,[R_SERIAL2_TR_CTRL] +#endif + +#ifdef CONFIG_ETRAX_SERIAL_PORT3 + ;; setup the serial port 3 at 115200 baud for debug purposes + + moveq IO_STATE (R_SERIAL3_XOFF, tx_stop, enable) \ + | IO_STATE (R_SERIAL3_XOFF, auto_xoff, disable) \ + | IO_FIELD (R_SERIAL3_XOFF, xoff_char, 0),$r0 + move.d $r0,[R_SERIAL3_XOFF] + + ; 115.2kbaud for both transmit and receive + move.b IO_STATE (R_SERIAL3_BAUD, tr_baud, c115k2Hz) \ + | IO_STATE (R_SERIAL3_BAUD, rec_baud, c115k2Hz),$r0 + move.b $r0,[R_SERIAL3_BAUD] + + ; Set up and enable the serial3 receiver. + move.b IO_STATE (R_SERIAL3_REC_CTRL, dma_err, stop) \ + | IO_STATE (R_SERIAL3_REC_CTRL, rec_enable, enable) \ + | IO_STATE (R_SERIAL3_REC_CTRL, rts_, active) \ + | IO_STATE (R_SERIAL3_REC_CTRL, sampling, middle) \ + | IO_STATE (R_SERIAL3_REC_CTRL, rec_stick_par, normal) \ + | IO_STATE (R_SERIAL3_REC_CTRL, rec_par, even) \ + | IO_STATE (R_SERIAL3_REC_CTRL, rec_par_en, disable) \ + | IO_STATE (R_SERIAL3_REC_CTRL, rec_bitnr, rec_8bit),$r0 + move.b $r0,[R_SERIAL3_REC_CTRL] + + ; Set up and enable the serial3 transmitter. + move.b IO_FIELD (R_SERIAL3_TR_CTRL, txd, 0) \ + | IO_STATE (R_SERIAL3_TR_CTRL, tr_enable, enable) \ + | IO_STATE (R_SERIAL3_TR_CTRL, auto_cts, disabled) \ + | IO_STATE (R_SERIAL3_TR_CTRL, stop_bits, one_bit) \ + | IO_STATE (R_SERIAL3_TR_CTRL, tr_stick_par, normal) \ + | IO_STATE (R_SERIAL3_TR_CTRL, tr_par, even) \ + | IO_STATE (R_SERIAL3_TR_CTRL, tr_par_en, disable) \ + | IO_STATE (R_SERIAL3_TR_CTRL, tr_bitnr, tr_8bit),$r0 + move.b $r0,[R_SERIAL3_TR_CTRL] +#endif + + jump start_kernel ; jump into the C-function start_kernel in init/main.c + + .data +etrax_irv: + .dword 0 +romfs_start: + .dword 0 +romfs_length: + .dword 0 +romfs_in_flash: + .dword 0 + + ;; put some special pages at the beginning of the kernel aligned + ;; to page boundaries - the kernel cannot start until after this + +#ifdef CONFIG_CRIS_LOW_MAP +swapper_pg_dir = 0x60002000 +#else +swapper_pg_dir = 0xc0002000 +#endif + + .section ".init.data", "aw" +#include "../lib/hw_settings.S" |