diff options
Diffstat (limited to 'kernel/arch/arm/mach-orion5x/kurobox_pro-setup.c')
| -rw-r--r-- | kernel/arch/arm/mach-orion5x/kurobox_pro-setup.c | 408 |
1 files changed, 408 insertions, 0 deletions
diff --git a/kernel/arch/arm/mach-orion5x/kurobox_pro-setup.c b/kernel/arch/arm/mach-orion5x/kurobox_pro-setup.c new file mode 100644 index 000000000..fe6a48a32 --- /dev/null +++ b/kernel/arch/arm/mach-orion5x/kurobox_pro-setup.c @@ -0,0 +1,408 @@ +/* + * arch/arm/mach-orion5x/kurobox_pro-setup.c + * + * Maintainer: Ronen Shitrit <rshitrit@marvell.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ +#include <linux/gpio.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/delay.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/nand.h> +#include <linux/mv643xx_eth.h> +#include <linux/i2c.h> +#include <linux/serial_reg.h> +#include <linux/ata_platform.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <mach/orion5x.h> +#include <linux/platform_data/mtd-orion_nand.h> +#include "common.h" +#include "mpp.h" + +/***************************************************************************** + * KUROBOX-PRO Info + ****************************************************************************/ + +/* + * 256K NOR flash Device bus boot chip select + */ + +#define KUROBOX_PRO_NOR_BOOT_BASE 0xf4000000 +#define KUROBOX_PRO_NOR_BOOT_SIZE SZ_256K + +/* + * 256M NAND flash on Device bus chip select 1 + */ + +#define KUROBOX_PRO_NAND_BASE 0xfc000000 +#define KUROBOX_PRO_NAND_SIZE SZ_2M + +/***************************************************************************** + * 256MB NAND Flash on Device bus CS0 + ****************************************************************************/ + +static struct mtd_partition kurobox_pro_nand_parts[] = { + { + .name = "uImage", + .offset = 0, + .size = SZ_4M, + }, { + .name = "rootfs", + .offset = SZ_4M, + .size = SZ_64M, + }, { + .name = "extra", + .offset = SZ_4M + SZ_64M, + .size = SZ_256M - (SZ_4M + SZ_64M), + }, +}; + +static struct resource kurobox_pro_nand_resource = { + .flags = IORESOURCE_MEM, + .start = KUROBOX_PRO_NAND_BASE, + .end = KUROBOX_PRO_NAND_BASE + KUROBOX_PRO_NAND_SIZE - 1, +}; + +static struct orion_nand_data kurobox_pro_nand_data = { + .parts = kurobox_pro_nand_parts, + .nr_parts = ARRAY_SIZE(kurobox_pro_nand_parts), + .cle = 0, + .ale = 1, + .width = 8, +}; + +static struct platform_device kurobox_pro_nand_flash = { + .name = "orion_nand", + .id = -1, + .dev = { + .platform_data = &kurobox_pro_nand_data, + }, + .resource = &kurobox_pro_nand_resource, + .num_resources = 1, +}; + +/***************************************************************************** + * 256KB NOR Flash on BOOT Device + ****************************************************************************/ + +static struct physmap_flash_data kurobox_pro_nor_flash_data = { + .width = 1, +}; + +static struct resource kurobox_pro_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = KUROBOX_PRO_NOR_BOOT_BASE, + .end = KUROBOX_PRO_NOR_BOOT_BASE + KUROBOX_PRO_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device kurobox_pro_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &kurobox_pro_nor_flash_data, + }, + .num_resources = 1, + .resource = &kurobox_pro_nor_flash_resource, +}; + +/***************************************************************************** + * PCI + ****************************************************************************/ + +static int __init kurobox_pro_pci_map_irq(const struct pci_dev *dev, u8 slot, + u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1) + return irq; + + /* + * PCI isn't used on the Kuro + */ + return -1; +} + +static struct hw_pci kurobox_pro_pci __initdata = { + .nr_controllers = 2, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = kurobox_pro_pci_map_irq, +}; + +static int __init kurobox_pro_pci_init(void) +{ + if (machine_is_kurobox_pro()) { + orion5x_pci_disable(); + pci_common_init(&kurobox_pro_pci); + } + + return 0; +} + +subsys_initcall(kurobox_pro_pci_init); + +/***************************************************************************** + * Ethernet + ****************************************************************************/ + +static struct mv643xx_eth_platform_data kurobox_pro_eth_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(8), +}; + +/***************************************************************************** + * RTC 5C372a on I2C bus + ****************************************************************************/ +static struct i2c_board_info __initdata kurobox_pro_i2c_rtc = { + I2C_BOARD_INFO("rs5c372a", 0x32), +}; + +/***************************************************************************** + * SATA + ****************************************************************************/ +static struct mv_sata_platform_data kurobox_pro_sata_data = { + .n_ports = 2, +}; + +/***************************************************************************** + * Kurobox Pro specific power off method via UART1-attached microcontroller + ****************************************************************************/ + +#define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2)) + +static int kurobox_pro_miconread(unsigned char *buf, int count) +{ + int i; + int timeout; + + for (i = 0; i < count; i++) { + timeout = 10; + + while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) { + if (--timeout == 0) + break; + udelay(1000); + } + + if (timeout == 0) + break; + buf[i] = readl(UART1_REG(RX)); + } + + /* return read bytes */ + return i; +} + +static int kurobox_pro_miconwrite(const unsigned char *buf, int count) +{ + int i = 0; + + while (count--) { + while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE)) + barrier(); + writel(buf[i++], UART1_REG(TX)); + } + + return 0; +} + +static int kurobox_pro_miconsend(const unsigned char *data, int count) +{ + int i; + unsigned char checksum = 0; + unsigned char recv_buf[40]; + unsigned char send_buf[40]; + unsigned char correct_ack[3]; + int retry = 2; + + /* Generate checksum */ + for (i = 0; i < count; i++) + checksum -= data[i]; + + do { + /* Send data */ + kurobox_pro_miconwrite(data, count); + + /* send checksum */ + kurobox_pro_miconwrite(&checksum, 1); + + if (kurobox_pro_miconread(recv_buf, sizeof(recv_buf)) <= 3) { + printk(KERN_ERR ">%s: receive failed.\n", __func__); + + /* send preamble to clear the receive buffer */ + memset(&send_buf, 0xff, sizeof(send_buf)); + kurobox_pro_miconwrite(send_buf, sizeof(send_buf)); + + /* make dummy reads */ + mdelay(100); + kurobox_pro_miconread(recv_buf, sizeof(recv_buf)); + } else { + /* Generate expected ack */ + correct_ack[0] = 0x01; + correct_ack[1] = data[1]; + correct_ack[2] = 0x00; + + /* checksum Check */ + if ((recv_buf[0] + recv_buf[1] + recv_buf[2] + + recv_buf[3]) & 0xFF) { + printk(KERN_ERR ">%s: Checksum Error : " + "Received data[%02x, %02x, %02x, %02x]" + "\n", __func__, recv_buf[0], + recv_buf[1], recv_buf[2], recv_buf[3]); + } else { + /* Check Received Data */ + if (correct_ack[0] == recv_buf[0] && + correct_ack[1] == recv_buf[1] && + correct_ack[2] == recv_buf[2]) { + /* Interval for next command */ + mdelay(10); + + /* Receive ACK */ + return 0; + } + } + /* Received NAK or illegal Data */ + printk(KERN_ERR ">%s: Error : NAK or Illegal Data " + "Received\n", __func__); + } + } while (retry--); + + /* Interval for next command */ + mdelay(10); + + return -1; +} + +static void kurobox_pro_power_off(void) +{ + const unsigned char watchdogkill[] = {0x01, 0x35, 0x00}; + const unsigned char shutdownwait[] = {0x00, 0x0c}; + const unsigned char poweroff[] = {0x00, 0x06}; + /* 38400 baud divisor */ + const unsigned divisor = ((orion5x_tclk + (8 * 38400)) / (16 * 38400)); + + pr_info("%s: triggering power-off...\n", __func__); + + /* hijack uart1 and reset into sane state (38400,8n1,even parity) */ + writel(0x83, UART1_REG(LCR)); + writel(divisor & 0xff, UART1_REG(DLL)); + writel((divisor >> 8) & 0xff, UART1_REG(DLM)); + writel(0x1b, UART1_REG(LCR)); + writel(0x00, UART1_REG(IER)); + writel(0x07, UART1_REG(FCR)); + writel(0x00, UART1_REG(MCR)); + + /* Send the commands to shutdown the Kurobox Pro */ + kurobox_pro_miconsend(watchdogkill, sizeof(watchdogkill)) ; + kurobox_pro_miconsend(shutdownwait, sizeof(shutdownwait)) ; + kurobox_pro_miconsend(poweroff, sizeof(poweroff)); +} + +/***************************************************************************** + * General Setup + ****************************************************************************/ +static unsigned int kurobox_pro_mpp_modes[] __initdata = { + MPP0_UNUSED, + MPP1_UNUSED, + MPP2_GPIO, /* GPIO Micon */ + MPP3_GPIO, /* GPIO Rtc */ + MPP4_UNUSED, + MPP5_UNUSED, + MPP6_NAND, /* NAND Flash REn */ + MPP7_NAND, /* NAND Flash WEn */ + MPP8_UNUSED, + MPP9_UNUSED, + MPP10_UNUSED, + MPP11_UNUSED, + MPP12_SATA_LED, /* SATA 0 presence */ + MPP13_SATA_LED, /* SATA 1 presence */ + MPP14_SATA_LED, /* SATA 0 active */ + MPP15_SATA_LED, /* SATA 1 active */ + MPP16_UART, /* UART1 RXD */ + MPP17_UART, /* UART1 TXD */ + MPP18_UART, /* UART1 CTSn */ + MPP19_UART, /* UART1 RTSn */ + 0, +}; + +static void __init kurobox_pro_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + orion5x_mpp_conf(kurobox_pro_mpp_modes); + + /* + * Configure peripherals. + */ + orion5x_ehci0_init(); + orion5x_ehci1_init(); + orion5x_eth_init(&kurobox_pro_eth_data); + orion5x_i2c_init(); + orion5x_sata_init(&kurobox_pro_sata_data); + orion5x_uart0_init(); + orion5x_uart1_init(); + orion5x_xor_init(); + + mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET, + ORION_MBUS_DEVBUS_BOOT_ATTR, + KUROBOX_PRO_NOR_BOOT_BASE, + KUROBOX_PRO_NOR_BOOT_SIZE); + platform_device_register(&kurobox_pro_nor_flash); + + if (machine_is_kurobox_pro()) { + mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(0), + ORION_MBUS_DEVBUS_ATTR(0), + KUROBOX_PRO_NAND_BASE, + KUROBOX_PRO_NAND_SIZE); + platform_device_register(&kurobox_pro_nand_flash); + } + + i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1); + + /* register Kurobox Pro specific power-off method */ + pm_power_off = kurobox_pro_power_off; +} + +#ifdef CONFIG_MACH_KUROBOX_PRO +MACHINE_START(KUROBOX_PRO, "Buffalo/Revogear Kurobox Pro") + /* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */ + .atag_offset = 0x100, + .init_machine = kurobox_pro_init, + .map_io = orion5x_map_io, + .init_early = orion5x_init_early, + .init_irq = orion5x_init_irq, + .init_time = orion5x_timer_init, + .fixup = tag_fixup_mem32, + .restart = orion5x_restart, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_LINKSTATION_PRO +MACHINE_START(LINKSTATION_PRO, "Buffalo Linkstation Pro/Live") + /* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */ + .atag_offset = 0x100, + .init_machine = kurobox_pro_init, + .map_io = orion5x_map_io, + .init_early = orion5x_init_early, + .init_irq = orion5x_init_irq, + .init_time = orion5x_timer_init, + .fixup = tag_fixup_mem32, + .restart = orion5x_restart, +MACHINE_END +#endif |