summaryrefslogtreecommitdiffstats
path: root/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi')
-rw-r--r--kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi56
1 files changed, 51 insertions, 5 deletions
diff --git a/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi b/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi
index 782ab1ff1..cfe140c65 100644
--- a/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi
+++ b/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi
@@ -199,6 +199,38 @@
gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; /* GPIO_108 */
};
};
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* GPIO_16 */
+ vcc-supply = <&vaux2>;
+ };
+
+ /* HS USB Host VBUS supply
+ * disabling this regulator causes current leakage, and LCD flicker
+ * on earlier (CC) board revisions, so keep it always on */
+ usb_host_5v: fixed-regulator-usb_host_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_host_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* GPIO_164 */
+ };
+
+ /* wg7210 (wifi+bt module) 32k clock buffer */
+ wg7210_32k: fixed-regulator-wg7210_32k {
+ compatible = "regulator-fixed";
+ regulator-name = "wg7210_32k";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ enable-active-high;
+ gpio = <&twl_gpio 13 GPIO_ACTIVE_HIGH>;
+ };
};
&omap3_pmx_core {
@@ -459,13 +491,18 @@
power = <50>;
};
+/*
+ * Many pandora boards have been produced with defective write-protect switches
+ * on either slot, so it was decided not to use this feature. If you know
+ * your board has good switches, feel free to uncomment wp-gpios below.
+ */
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <&vmmc1>;
bus-width = <4>;
cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; /* GPIO_126 */
+ /*wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;*/ /* GPIO_126 */
};
&mmc2 {
@@ -473,8 +510,13 @@
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&vmmc2>;
bus-width = <4>;
- cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_HIGH>;
- wp-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* GPIO_127 */
+ cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_LOW>;
+ /*wp-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;*/ /* GPIO_127 */
+};
+
+/* mmc3 is probed using pdata-quirks to pass wl1251 card data */
+&mmc3 {
+ status = "disabled";
};
/* bluetooth*/
@@ -496,6 +538,10 @@
port2-mode = "ehci-phy";
};
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
&gpmc {
ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
@@ -545,7 +591,7 @@
reg = <0x280000 0xa00000>;
};
- filesystem@680000 {
+ filesystem@c80000 {
label = "rootfs";
reg = <0xc80000 0>; /* 0 = MTDPART_SIZ_FULL */
};
@@ -561,7 +607,7 @@
pinctrl-0 = <&penirq_pins>;
interrupt-parent = <&gpio3>;
interrupts = <30 0>; /* GPIO_94 */
- pendown-gpio = <&gpio3 30 0>;
+ pendown-gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
vcc-supply = <&vaux4>;
ti,x-min = /bits/ 16 <0>;