summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/rpmsg.txt
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/rpmsg.txt')
-rw-r--r--kernel/Documentation/rpmsg.txt293
1 files changed, 293 insertions, 0 deletions
diff --git a/kernel/Documentation/rpmsg.txt b/kernel/Documentation/rpmsg.txt
new file mode 100644
index 000000000..f7edc3aa1
--- /dev/null
+++ b/kernel/Documentation/rpmsg.txt
@@ -0,0 +1,293 @@
+Remote Processor Messaging (rpmsg) Framework
+
+Note: this document describes the rpmsg bus and how to write rpmsg drivers.
+To learn how to add rpmsg support for new platforms, check out remoteproc.txt
+(also a resident of Documentation/).
+
+1. Introduction
+
+Modern SoCs typically employ heterogeneous remote processor devices in
+asymmetric multiprocessing (AMP) configurations, which may be running
+different instances of operating system, whether it's Linux or any other
+flavor of real-time OS.
+
+OMAP4, for example, has dual Cortex-A9, dual Cortex-M3 and a C64x+ DSP.
+Typically, the dual cortex-A9 is running Linux in a SMP configuration,
+and each of the other three cores (two M3 cores and a DSP) is running
+its own instance of RTOS in an AMP configuration.
+
+Typically AMP remote processors employ dedicated DSP codecs and multimedia
+hardware accelerators, and therefore are often used to offload CPU-intensive
+multimedia tasks from the main application processor.
+
+These remote processors could also be used to control latency-sensitive
+sensors, drive random hardware blocks, or just perform background tasks
+while the main CPU is idling.
+
+Users of those remote processors can either be userland apps (e.g. multimedia
+frameworks talking with remote OMX components) or kernel drivers (controlling
+hardware accessible only by the remote processor, reserving kernel-controlled
+resources on behalf of the remote processor, etc..).
+
+Rpmsg is a virtio-based messaging bus that allows kernel drivers to communicate
+with remote processors available on the system. In turn, drivers could then
+expose appropriate user space interfaces, if needed.
+
+When writing a driver that exposes rpmsg communication to userland, please
+keep in mind that remote processors might have direct access to the
+system's physical memory and other sensitive hardware resources (e.g. on
+OMAP4, remote cores and hardware accelerators may have direct access to the
+physical memory, gpio banks, dma controllers, i2c bus, gptimers, mailbox
+devices, hwspinlocks, etc..). Moreover, those remote processors might be
+running RTOS where every task can access the entire memory/devices exposed
+to the processor. To minimize the risks of rogue (or buggy) userland code
+exploiting remote bugs, and by that taking over the system, it is often
+desired to limit userland to specific rpmsg channels (see definition below)
+it can send messages on, and if possible, minimize how much control
+it has over the content of the messages.
+
+Every rpmsg device is a communication channel with a remote processor (thus
+rpmsg devices are called channels). Channels are identified by a textual name
+and have a local ("source") rpmsg address, and remote ("destination") rpmsg
+address.
+
+When a driver starts listening on a channel, its rx callback is bound with
+a unique rpmsg local address (a 32-bit integer). This way when inbound messages
+arrive, the rpmsg core dispatches them to the appropriate driver according
+to their destination address (this is done by invoking the driver's rx handler
+with the payload of the inbound message).
+
+
+2. User API
+
+ int rpmsg_send(struct rpmsg_channel *rpdev, void *data, int len);
+ - sends a message across to the remote processor on a given channel.
+ The caller should specify the channel, the data it wants to send,
+ and its length (in bytes). The message will be sent on the specified
+ channel, i.e. its source and destination address fields will be
+ set to the channel's src and dst addresses.
+
+ In case there are no TX buffers available, the function will block until
+ one becomes available (i.e. until the remote processor consumes
+ a tx buffer and puts it back on virtio's used descriptor ring),
+ or a timeout of 15 seconds elapses. When the latter happens,
+ -ERESTARTSYS is returned.
+ The function can only be called from a process context (for now).
+ Returns 0 on success and an appropriate error value on failure.
+
+ int rpmsg_sendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst);
+ - sends a message across to the remote processor on a given channel,
+ to a destination address provided by the caller.
+ The caller should specify the channel, the data it wants to send,
+ its length (in bytes), and an explicit destination address.
+ The message will then be sent to the remote processor to which the
+ channel belongs, using the channel's src address, and the user-provided
+ dst address (thus the channel's dst address will be ignored).
+
+ In case there are no TX buffers available, the function will block until
+ one becomes available (i.e. until the remote processor consumes
+ a tx buffer and puts it back on virtio's used descriptor ring),
+ or a timeout of 15 seconds elapses. When the latter happens,
+ -ERESTARTSYS is returned.
+ The function can only be called from a process context (for now).
+ Returns 0 on success and an appropriate error value on failure.
+
+ int rpmsg_send_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst,
+ void *data, int len);
+ - sends a message across to the remote processor, using the src and dst
+ addresses provided by the user.
+ The caller should specify the channel, the data it wants to send,
+ its length (in bytes), and explicit source and destination addresses.
+ The message will then be sent to the remote processor to which the
+ channel belongs, but the channel's src and dst addresses will be
+ ignored (and the user-provided addresses will be used instead).
+
+ In case there are no TX buffers available, the function will block until
+ one becomes available (i.e. until the remote processor consumes
+ a tx buffer and puts it back on virtio's used descriptor ring),
+ or a timeout of 15 seconds elapses. When the latter happens,
+ -ERESTARTSYS is returned.
+ The function can only be called from a process context (for now).
+ Returns 0 on success and an appropriate error value on failure.
+
+ int rpmsg_trysend(struct rpmsg_channel *rpdev, void *data, int len);
+ - sends a message across to the remote processor on a given channel.
+ The caller should specify the channel, the data it wants to send,
+ and its length (in bytes). The message will be sent on the specified
+ channel, i.e. its source and destination address fields will be
+ set to the channel's src and dst addresses.
+
+ In case there are no TX buffers available, the function will immediately
+ return -ENOMEM without waiting until one becomes available.
+ The function can only be called from a process context (for now).
+ Returns 0 on success and an appropriate error value on failure.
+
+ int rpmsg_trysendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst)
+ - sends a message across to the remote processor on a given channel,
+ to a destination address provided by the user.
+ The user should specify the channel, the data it wants to send,
+ its length (in bytes), and an explicit destination address.
+ The message will then be sent to the remote processor to which the
+ channel belongs, using the channel's src address, and the user-provided
+ dst address (thus the channel's dst address will be ignored).
+
+ In case there are no TX buffers available, the function will immediately
+ return -ENOMEM without waiting until one becomes available.
+ The function can only be called from a process context (for now).
+ Returns 0 on success and an appropriate error value on failure.
+
+ int rpmsg_trysend_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst,
+ void *data, int len);
+ - sends a message across to the remote processor, using source and
+ destination addresses provided by the user.
+ The user should specify the channel, the data it wants to send,
+ its length (in bytes), and explicit source and destination addresses.
+ The message will then be sent to the remote processor to which the
+ channel belongs, but the channel's src and dst addresses will be
+ ignored (and the user-provided addresses will be used instead).
+
+ In case there are no TX buffers available, the function will immediately
+ return -ENOMEM without waiting until one becomes available.
+ The function can only be called from a process context (for now).
+ Returns 0 on success and an appropriate error value on failure.
+
+ struct rpmsg_endpoint *rpmsg_create_ept(struct rpmsg_channel *rpdev,
+ void (*cb)(struct rpmsg_channel *, void *, int, void *, u32),
+ void *priv, u32 addr);
+ - every rpmsg address in the system is bound to an rx callback (so when
+ inbound messages arrive, they are dispatched by the rpmsg bus using the
+ appropriate callback handler) by means of an rpmsg_endpoint struct.
+
+ This function allows drivers to create such an endpoint, and by that,
+ bind a callback, and possibly some private data too, to an rpmsg address
+ (either one that is known in advance, or one that will be dynamically
+ assigned for them).
+
+ Simple rpmsg drivers need not call rpmsg_create_ept, because an endpoint
+ is already created for them when they are probed by the rpmsg bus
+ (using the rx callback they provide when they registered to the rpmsg bus).
+
+ So things should just work for simple drivers: they already have an
+ endpoint, their rx callback is bound to their rpmsg address, and when
+ relevant inbound messages arrive (i.e. messages which their dst address
+ equals to the src address of their rpmsg channel), the driver's handler
+ is invoked to process it.
+
+ That said, more complicated drivers might do need to allocate
+ additional rpmsg addresses, and bind them to different rx callbacks.
+ To accomplish that, those drivers need to call this function.
+ Drivers should provide their channel (so the new endpoint would bind
+ to the same remote processor their channel belongs to), an rx callback
+ function, an optional private data (which is provided back when the
+ rx callback is invoked), and an address they want to bind with the
+ callback. If addr is RPMSG_ADDR_ANY, then rpmsg_create_ept will
+ dynamically assign them an available rpmsg address (drivers should have
+ a very good reason why not to always use RPMSG_ADDR_ANY here).
+
+ Returns a pointer to the endpoint on success, or NULL on error.
+
+ void rpmsg_destroy_ept(struct rpmsg_endpoint *ept);
+ - destroys an existing rpmsg endpoint. user should provide a pointer
+ to an rpmsg endpoint that was previously created with rpmsg_create_ept().
+
+ int register_rpmsg_driver(struct rpmsg_driver *rpdrv);
+ - registers an rpmsg driver with the rpmsg bus. user should provide
+ a pointer to an rpmsg_driver struct, which contains the driver's
+ ->probe() and ->remove() functions, an rx callback, and an id_table
+ specifying the names of the channels this driver is interested to
+ be probed with.
+
+ void unregister_rpmsg_driver(struct rpmsg_driver *rpdrv);
+ - unregisters an rpmsg driver from the rpmsg bus. user should provide
+ a pointer to a previously-registered rpmsg_driver struct.
+ Returns 0 on success, and an appropriate error value on failure.
+
+
+3. Typical usage
+
+The following is a simple rpmsg driver, that sends an "hello!" message
+on probe(), and whenever it receives an incoming message, it dumps its
+content to the console.
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/rpmsg.h>
+
+static void rpmsg_sample_cb(struct rpmsg_channel *rpdev, void *data, int len,
+ void *priv, u32 src)
+{
+ print_hex_dump(KERN_INFO, "incoming message:", DUMP_PREFIX_NONE,
+ 16, 1, data, len, true);
+}
+
+static int rpmsg_sample_probe(struct rpmsg_channel *rpdev)
+{
+ int err;
+
+ dev_info(&rpdev->dev, "chnl: 0x%x -> 0x%x\n", rpdev->src, rpdev->dst);
+
+ /* send a message on our channel */
+ err = rpmsg_send(rpdev, "hello!", 6);
+ if (err) {
+ pr_err("rpmsg_send failed: %d\n", err);
+ return err;
+ }
+
+ return 0;
+}
+
+static void rpmsg_sample_remove(struct rpmsg_channel *rpdev)
+{
+ dev_info(&rpdev->dev, "rpmsg sample client driver is removed\n");
+}
+
+static struct rpmsg_device_id rpmsg_driver_sample_id_table[] = {
+ { .name = "rpmsg-client-sample" },
+ { },
+};
+MODULE_DEVICE_TABLE(rpmsg, rpmsg_driver_sample_id_table);
+
+static struct rpmsg_driver rpmsg_sample_client = {
+ .drv.name = KBUILD_MODNAME,
+ .drv.owner = THIS_MODULE,
+ .id_table = rpmsg_driver_sample_id_table,
+ .probe = rpmsg_sample_probe,
+ .callback = rpmsg_sample_cb,
+ .remove = rpmsg_sample_remove,
+};
+
+static int __init init(void)
+{
+ return register_rpmsg_driver(&rpmsg_sample_client);
+}
+module_init(init);
+
+static void __exit fini(void)
+{
+ unregister_rpmsg_driver(&rpmsg_sample_client);
+}
+module_exit(fini);
+
+Note: a similar sample which can be built and loaded can be found
+in samples/rpmsg/.
+
+4. Allocations of rpmsg channels:
+
+At this point we only support dynamic allocations of rpmsg channels.
+
+This is possible only with remote processors that have the VIRTIO_RPMSG_F_NS
+virtio device feature set. This feature bit means that the remote
+processor supports dynamic name service announcement messages.
+
+When this feature is enabled, creation of rpmsg devices (i.e. channels)
+is completely dynamic: the remote processor announces the existence of a
+remote rpmsg service by sending a name service message (which contains
+the name and rpmsg addr of the remote service, see struct rpmsg_ns_msg).
+
+This message is then handled by the rpmsg bus, which in turn dynamically
+creates and registers an rpmsg channel (which represents the remote service).
+If/when a relevant rpmsg driver is registered, it will be immediately probed
+by the bus, and can then start sending messages to the remote service.
+
+The plan is also to add static creation of rpmsg channels via the virtio
+config space, but it's not implemented yet.