diff options
Diffstat (limited to 'kernel/Documentation/ramoops.txt')
| -rw-r--r-- | kernel/Documentation/ramoops.txt | 128 |
1 files changed, 128 insertions, 0 deletions
diff --git a/kernel/Documentation/ramoops.txt b/kernel/Documentation/ramoops.txt new file mode 100644 index 000000000..5d8675615 --- /dev/null +++ b/kernel/Documentation/ramoops.txt @@ -0,0 +1,128 @@ +Ramoops oops/panic logger +========================= + +Sergiu Iordache <sergiu@chromium.org> + +Updated: 17 November 2011 + +0. Introduction + +Ramoops is an oops/panic logger that writes its logs to RAM before the system +crashes. It works by logging oopses and panics in a circular buffer. Ramoops +needs a system with persistent RAM so that the content of that area can +survive after a restart. + +1. Ramoops concepts + +Ramoops uses a predefined memory area to store the dump. The start and size +and type of the memory area are set using three variables: + * "mem_address" for the start + * "mem_size" for the size. The memory size will be rounded down to a + power of two. + * "mem_type" to specifiy if the memory type (default is pgprot_writecombine). + +Typically the default value of mem_type=0 should be used as that sets the pstore +mapping to pgprot_writecombine. Setting mem_type=1 attempts to use +pgprot_noncached, which only works on some platforms. This is because pstore +depends on atomic operations. At least on ARM, pgprot_noncached causes the +memory to be mapped strongly ordered, and atomic operations on strongly ordered +memory are implementation defined, and won't work on many ARMs such as omaps. + +The memory area is divided into "record_size" chunks (also rounded down to +power of two) and each oops/panic writes a "record_size" chunk of +information. + +Dumping both oopses and panics can be done by setting 1 in the "dump_oops" +variable while setting 0 in that variable dumps only the panics. + +The module uses a counter to record multiple dumps but the counter gets reset +on restart (i.e. new dumps after the restart will overwrite old ones). + +Ramoops also supports software ECC protection of persistent memory regions. +This might be useful when a hardware reset was used to bring the machine back +to life (i.e. a watchdog triggered). In such cases, RAM may be somewhat +corrupt, but usually it is restorable. + +2. Setting the parameters + +Setting the ramoops parameters can be done in 2 different manners: + 1. Use the module parameters (which have the names of the variables described + as before). + For quick debugging, you can also reserve parts of memory during boot + and then use the reserved memory for ramoops. For example, assuming a machine + with > 128 MB of memory, the following kernel command line will tell the + kernel to use only the first 128 MB of memory, and place ECC-protected ramoops + region at 128 MB boundary: + "mem=128M ramoops.mem_address=0x8000000 ramoops.ecc=1" + 2. Use a platform device and set the platform data. The parameters can then + be set through that platform data. An example of doing that is: + +#include <linux/pstore_ram.h> +[...] + +static struct ramoops_platform_data ramoops_data = { + .mem_size = <...>, + .mem_address = <...>, + .mem_type = <...>, + .record_size = <...>, + .dump_oops = <...>, + .ecc = <...>, +}; + +static struct platform_device ramoops_dev = { + .name = "ramoops", + .dev = { + .platform_data = &ramoops_data, + }, +}; + +[... inside a function ...] +int ret; + +ret = platform_device_register(&ramoops_dev); +if (ret) { + printk(KERN_ERR "unable to register platform device\n"); + return ret; +} + +You can specify either RAM memory or peripheral devices' memory. However, when +specifying RAM, be sure to reserve the memory by issuing memblock_reserve() +very early in the architecture code, e.g.: + +#include <linux/memblock.h> + +memblock_reserve(ramoops_data.mem_address, ramoops_data.mem_size); + +3. Dump format + +The data dump begins with a header, currently defined as "====" followed by a +timestamp and a new line. The dump then continues with the actual data. + +4. Reading the data + +The dump data can be read from the pstore filesystem. The format for these +files is "dmesg-ramoops-N", where N is the record number in memory. To delete +a stored record from RAM, simply unlink the respective pstore file. + +5. Persistent function tracing + +Persistent function tracing might be useful for debugging software or hardware +related hangs. The functions call chain log is stored in a "ftrace-ramoops" +file. Here is an example of usage: + + # mount -t debugfs debugfs /sys/kernel/debug/ + # echo 1 > /sys/kernel/debug/pstore/record_ftrace + # reboot -f + [...] + # mount -t pstore pstore /mnt/ + # tail /mnt/ftrace-ramoops + 0 ffffffff8101ea64 ffffffff8101bcda native_apic_mem_read <- disconnect_bsp_APIC+0x6a/0xc0 + 0 ffffffff8101ea44 ffffffff8101bcf6 native_apic_mem_write <- disconnect_bsp_APIC+0x86/0xc0 + 0 ffffffff81020084 ffffffff8101a4b5 hpet_disable <- native_machine_shutdown+0x75/0x90 + 0 ffffffff81005f94 ffffffff8101a4bb iommu_shutdown_noop <- native_machine_shutdown+0x7b/0x90 + 0 ffffffff8101a6a1 ffffffff8101a437 native_machine_emergency_restart <- native_machine_restart+0x37/0x40 + 0 ffffffff811f9876 ffffffff8101a73a acpi_reboot <- native_machine_emergency_restart+0xaa/0x1e0 + 0 ffffffff8101a514 ffffffff8101a772 mach_reboot_fixups <- native_machine_emergency_restart+0xe2/0x1e0 + 0 ffffffff811d9c54 ffffffff8101a7a0 __const_udelay <- native_machine_emergency_restart+0x110/0x1e0 + 0 ffffffff811d9c34 ffffffff811d9c80 __delay <- __const_udelay+0x30/0x40 + 0 ffffffff811d9d14 ffffffff811d9c3f delay_tsc <- __delay+0xf/0x20 |