diff options
Diffstat (limited to 'kernel/Documentation/networking/skfp.txt')
| -rw-r--r-- | kernel/Documentation/networking/skfp.txt | 220 |
1 files changed, 220 insertions, 0 deletions
diff --git a/kernel/Documentation/networking/skfp.txt b/kernel/Documentation/networking/skfp.txt new file mode 100644 index 000000000..203ec66c9 --- /dev/null +++ b/kernel/Documentation/networking/skfp.txt @@ -0,0 +1,220 @@ +(C)Copyright 1998-2000 SysKonnect, +=========================================================================== + +skfp.txt created 11-May-2000 + +Readme File for skfp.o v2.06 + + +This file contains +(1) OVERVIEW +(2) SUPPORTED ADAPTERS +(3) GENERAL INFORMATION +(4) INSTALLATION +(5) INCLUSION OF THE ADAPTER IN SYSTEM START +(6) TROUBLESHOOTING +(7) FUNCTION OF THE ADAPTER LEDS +(8) HISTORY + +=========================================================================== + + + +(1) OVERVIEW +============ + +This README explains how to use the driver 'skfp' for Linux with your +network adapter. + +Chapter 2: Contains a list of all network adapters that are supported by + this driver. + +Chapter 3: Gives some general information. + +Chapter 4: Describes common problems and solutions. + +Chapter 5: Shows the changed functionality of the adapter LEDs. + +Chapter 6: History of development. + +*** + + +(2) SUPPORTED ADAPTERS +====================== + +The network driver 'skfp' supports the following network adapters: +SysKonnect adapters: + - SK-5521 (SK-NET FDDI-UP) + - SK-5522 (SK-NET FDDI-UP DAS) + - SK-5541 (SK-NET FDDI-FP) + - SK-5543 (SK-NET FDDI-LP) + - SK-5544 (SK-NET FDDI-LP DAS) + - SK-5821 (SK-NET FDDI-UP64) + - SK-5822 (SK-NET FDDI-UP64 DAS) + - SK-5841 (SK-NET FDDI-FP64) + - SK-5843 (SK-NET FDDI-LP64) + - SK-5844 (SK-NET FDDI-LP64 DAS) +Compaq adapters (not tested): + - Netelligent 100 FDDI DAS Fibre SC + - Netelligent 100 FDDI SAS Fibre SC + - Netelligent 100 FDDI DAS UTP + - Netelligent 100 FDDI SAS UTP + - Netelligent 100 FDDI SAS Fibre MIC +*** + + +(3) GENERAL INFORMATION +======================= + +From v2.01 on, the driver is integrated in the linux kernel sources. +Therefore, the installation is the same as for any other adapter +supported by the kernel. +Refer to the manual of your distribution about the installation +of network adapters. +Makes my life much easier :-) +*** + + +(4) TROUBLESHOOTING +=================== + +If you run into problems during installation, check those items: + +Problem: The FDDI adapter cannot be found by the driver. +Reason: Look in /proc/pci for the following entry: + 'FDDI network controller: SysKonnect SK-FDDI-PCI ...' + If this entry exists, then the FDDI adapter has been + found by the system and should be able to be used. + If this entry does not exist or if the file '/proc/pci' + is not there, then you may have a hardware problem or PCI + support may not be enabled in your kernel. + The adapter can be checked using the diagnostic program + which is available from the SysKonnect web site: + www.syskonnect.de + Some COMPAQ machines have a problem with PCI under + Linux. This is described in the 'PCI howto' document + (included in some distributions or available from the + www, e.g. at 'www.linux.org') and no workaround is available. + +Problem: You want to use your computer as a router between + multiple IP subnetworks (using multiple adapters), but + you cannot reach computers in other subnetworks. +Reason: Either the router's kernel is not configured for IP + forwarding or there is a problem with the routing table + and gateway configuration in at least one of the + computers. + +If your problem is not listed here, please contact our +technical support for help. +You can send email to: + linux@syskonnect.de +When contacting our technical support, +please ensure that the following information is available: +- System Manufacturer and Model +- Boards in your system +- Distribution +- Kernel version + +*** + + +(5) FUNCTION OF THE ADAPTER LEDS +================================ + + The functionality of the LED's on the FDDI network adapters was + changed in SMT version v2.82. With this new SMT version, the yellow + LED works as a ring operational indicator. An active yellow LED + indicates that the ring is down. The green LED on the adapter now + works as a link indicator where an active GREEN LED indicates that + the respective port has a physical connection. + + With versions of SMT prior to v2.82 a ring up was indicated if the + yellow LED was off while the green LED(s) showed the connection + status of the adapter. During a ring down the green LED was off and + the yellow LED was on. + + All implementations indicate that a driver is not loaded if + all LEDs are off. + +*** + + +(6) HISTORY +=========== + +v2.06 (20000511) (In-Kernel version) + New features: + - 64 bit support + - new pci dma interface + - in kernel 2.3.99 + +v2.05 (20000217) (In-Kernel version) + New features: + - Changes for 2.3.45 kernel + +v2.04 (20000207) (Standalone version) + New features: + - Added rx/tx byte counter + +v2.03 (20000111) (Standalone version) + Problems fixed: + - Fixed printk statements from v2.02 + +v2.02 (991215) (Standalone version) + Problems fixed: + - Removed unnecessary output + - Fixed path for "printver.sh" in makefile + +v2.01 (991122) (In-Kernel version) + New features: + - Integration in Linux kernel sources + - Support for memory mapped I/O. + +v2.00 (991112) + New features: + - Full source released under GPL + +v1.05 (991023) + Problems fixed: + - Compilation with kernel version 2.2.13 failed + +v1.04 (990427) + Changes: + - New SMT module included, changing LED functionality + Problems fixed: + - Synchronization on SMP machines was buggy + +v1.03 (990325) + Problems fixed: + - Interrupt routing on SMP machines could be incorrect + +v1.02 (990310) + New features: + - Support for kernel versions 2.2.x added + - Kernel patch instead of private duplicate of kernel functions + +v1.01 (980812) + Problems fixed: + Connection hangup with telnet + Slow telnet connection + +v1.00 beta 01 (980507) + New features: + None. + Problems fixed: + None. + Known limitations: + - tar archive instead of standard package format (rpm). + - FDDI statistic is empty. + - not tested with 2.1.xx kernels + - integration in kernel not tested + - not tested simultaneously with FDDI adapters from other vendors. + - only X86 processors supported. + - SBA (Synchronous Bandwidth Allocator) parameters can + not be configured. + - does not work on some COMPAQ machines. See the PCI howto + document for details about this problem. + - data corruption with kernel versions below 2.0.33. + +*** End of information file *** |