summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/networking/ipvlan.txt
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/networking/ipvlan.txt')
-rw-r--r--kernel/Documentation/networking/ipvlan.txt107
1 files changed, 107 insertions, 0 deletions
diff --git a/kernel/Documentation/networking/ipvlan.txt b/kernel/Documentation/networking/ipvlan.txt
new file mode 100644
index 000000000..cf996394e
--- /dev/null
+++ b/kernel/Documentation/networking/ipvlan.txt
@@ -0,0 +1,107 @@
+
+ IPVLAN Driver HOWTO
+
+Initial Release:
+ Mahesh Bandewar <maheshb AT google.com>
+
+1. Introduction:
+ This is conceptually very similar to the macvlan driver with one major
+exception of using L3 for mux-ing /demux-ing among slaves. This property makes
+the master device share the L2 with it's slave devices. I have developed this
+driver in conjuntion with network namespaces and not sure if there is use case
+outside of it.
+
+
+2. Building and Installation:
+ In order to build the driver, please select the config item CONFIG_IPVLAN.
+The driver can be built into the kernel (CONFIG_IPVLAN=y) or as a module
+(CONFIG_IPVLAN=m).
+
+
+3. Configuration:
+ There are no module parameters for this driver and it can be configured
+using IProute2/ip utility.
+
+ ip link add link <master-dev> <slave-dev> type ipvlan mode { l2 | L3 }
+
+ e.g. ip link add link ipvl0 eth0 type ipvlan mode l2
+
+
+4. Operating modes:
+ IPvlan has two modes of operation - L2 and L3. For a given master device,
+you can select one of these two modes and all slaves on that master will
+operate in the same (selected) mode. The RX mode is almost identical except
+that in L3 mode the slaves wont receive any multicast / broadcast traffic.
+L3 mode is more restrictive since routing is controlled from the other (mostly)
+default namespace.
+
+4.1 L2 mode:
+ In this mode TX processing happens on the stack instance attached to the
+slave device and packets are switched and queued to the master device to send
+out. In this mode the slaves will RX/TX multicast and broadcast (if applicable)
+as well.
+
+4.2 L3 mode:
+ In this mode TX processing upto L3 happens on the stack instance attached
+to the slave device and packets are switched to the stack instance of the
+master device for the L2 processing and routing from that instance will be
+used before packets are queued on the outbound device. In this mode the slaves
+will not receive nor can send multicast / broadcast traffic.
+
+
+5. What to choose (macvlan vs. ipvlan)?
+ These two devices are very similar in many regards and the specific use
+case could very well define which device to choose. if one of the following
+situations defines your use case then you can choose to use ipvlan -
+ (a) The Linux host that is connected to the external switch / router has
+policy configured that allows only one mac per port.
+ (b) No of virtual devices created on a master exceed the mac capacity and
+puts the NIC in promiscous mode and degraded performance is a concern.
+ (c) If the slave device is to be put into the hostile / untrusted network
+namespace where L2 on the slave could be changed / misused.
+
+
+6. Example configuration:
+
+ +=============================================================+
+ | Host: host1 |
+ | |
+ | +----------------------+ +----------------------+ |
+ | | NS:ns0 | | NS:ns1 | |
+ | | | | | |
+ | | | | | |
+ | | ipvl0 | | ipvl1 | |
+ | +----------#-----------+ +-----------#----------+ |
+ | # # |
+ | ################################ |
+ | # eth0 |
+ +==============================#==============================+
+
+
+ (a) Create two network namespaces - ns0, ns1
+ ip netns add ns0
+ ip netns add ns1
+
+ (b) Create two ipvlan slaves on eth0 (master device)
+ ip link add link eth0 ipvl0 type ipvlan mode l2
+ ip link add link eth0 ipvl1 type ipvlan mode l2
+
+ (c) Assign slaves to the respective network namespaces
+ ip link set dev ipvl0 netns ns0
+ ip link set dev ipvl1 netns ns1
+
+ (d) Now switch to the namespace (ns0 or ns1) to configure the slave devices
+ - For ns0
+ (1) ip netns exec ns0 bash
+ (2) ip link set dev ipvl0 up
+ (3) ip link set dev lo up
+ (4) ip -4 addr add 127.0.0.1 dev lo
+ (5) ip -4 addr add $IPADDR dev ipvl0
+ (6) ip -4 route add default via $ROUTER dev ipvl0
+ - For ns1
+ (1) ip netns exec ns1 bash
+ (2) ip link set dev ipvl1 up
+ (3) ip link set dev lo up
+ (4) ip -4 addr add 127.0.0.1 dev lo
+ (5) ip -4 addr add $IPADDR dev ipvl1
+ (6) ip -4 route add default via $ROUTER dev ipvl1