diff options
Diffstat (limited to 'kernel/Documentation/networking/cxacru.txt')
| -rw-r--r-- | kernel/Documentation/networking/cxacru.txt | 100 |
1 files changed, 100 insertions, 0 deletions
diff --git a/kernel/Documentation/networking/cxacru.txt b/kernel/Documentation/networking/cxacru.txt new file mode 100644 index 000000000..2cce04457 --- /dev/null +++ b/kernel/Documentation/networking/cxacru.txt @@ -0,0 +1,100 @@ +Firmware is required for this device: http://accessrunner.sourceforge.net/ + +While it is capable of managing/maintaining the ADSL connection without the +module loaded, the device will sometimes stop responding after unloading the +driver and it is necessary to unplug/remove power to the device to fix this. + +Note: support for cxacru-cf.bin has been removed. It was not loaded correctly +so it had no effect on the device configuration. Fixing it could have stopped +existing devices working when an invalid configuration is supplied. + +There is a script cxacru-cf.py to convert an existing file to the sysfs form. + +Detected devices will appear as ATM devices named "cxacru". In /sys/class/atm/ +these are directories named cxacruN where N is the device number. A symlink +named device points to the USB interface device's directory which contains +several sysfs attribute files for retrieving device statistics: + +* adsl_controller_version + +* adsl_headend +* adsl_headend_environment + Information about the remote headend. + +* adsl_config + Configuration writing interface. + Write parameters in hexadecimal format <index>=<value>, + separated by whitespace, e.g.: + "1=0 a=5" + Up to 7 parameters at a time will be sent and the modem will restart + the ADSL connection when any value is set. These are logged for future + reference. + +* downstream_attenuation (dB) +* downstream_bits_per_frame +* downstream_rate (kbps) +* downstream_snr_margin (dB) + Downstream stats. + +* upstream_attenuation (dB) +* upstream_bits_per_frame +* upstream_rate (kbps) +* upstream_snr_margin (dB) +* transmitter_power (dBm/Hz) + Upstream stats. + +* downstream_crc_errors +* downstream_fec_errors +* downstream_hec_errors +* upstream_crc_errors +* upstream_fec_errors +* upstream_hec_errors + Error counts. + +* line_startable + Indicates that ADSL support on the device + is/can be enabled, see adsl_start. + +* line_status + "initialising" + "down" + "attempting to activate" + "training" + "channel analysis" + "exchange" + "waiting" + "up" + + Changes between "down" and "attempting to activate" + if there is no signal. + +* link_status + "not connected" + "connected" + "lost" + +* mac_address + +* modulation + "" (when not connected) + "ANSI T1.413" + "ITU-T G.992.1 (G.DMT)" + "ITU-T G.992.2 (G.LITE)" + +* startup_attempts + Count of total attempts to initialise ADSL. + +To enable/disable ADSL, the following can be written to the adsl_state file: + "start" + "stop + "restart" (stops, waits 1.5s, then starts) + "poll" (used to resume status polling if it was disabled due to failure) + +Changes in adsl/line state are reported via kernel log messages: + [4942145.150704] ATM dev 0: ADSL state: running + [4942243.663766] ATM dev 0: ADSL line: down + [4942249.665075] ATM dev 0: ADSL line: attempting to activate + [4942253.654954] ATM dev 0: ADSL line: training + [4942255.666387] ATM dev 0: ADSL line: channel analysis + [4942259.656262] ATM dev 0: ADSL line: exchange + [2635357.696901] ATM dev 0: ADSL line: up (8128 kb/s down | 832 kb/s up) |