diff options
Diffstat (limited to 'kernel/Documentation/networking/arcnet.txt')
| -rw-r--r-- | kernel/Documentation/networking/arcnet.txt | 556 |
1 files changed, 556 insertions, 0 deletions
diff --git a/kernel/Documentation/networking/arcnet.txt b/kernel/Documentation/networking/arcnet.txt new file mode 100644 index 000000000..aff97f47c --- /dev/null +++ b/kernel/Documentation/networking/arcnet.txt @@ -0,0 +1,556 @@ +---------------------------------------------------------------------------- +NOTE: See also arcnet-hardware.txt in this directory for jumper-setting +and cabling information if you're like many of us and didn't happen to get a +manual with your ARCnet card. +---------------------------------------------------------------------------- + +Since no one seems to listen to me otherwise, perhaps a poem will get your +attention: + This driver's getting fat and beefy, + But my cat is still named Fifi. + +Hmm, I think I'm allowed to call that a poem, even though it's only two +lines. Hey, I'm in Computer Science, not English. Give me a break. + +The point is: I REALLY REALLY REALLY REALLY REALLY want to hear from you if +you test this and get it working. Or if you don't. Or anything. + +ARCnet 0.32 ALPHA first made it into the Linux kernel 1.1.80 - this was +nice, but after that even FEWER people started writing to me because they +didn't even have to install the patch. <sigh> + +Come on, be a sport! Send me a success report! + +(hey, that was even better than my original poem... this is getting bad!) + + +-------- +WARNING: +-------- + +If you don't e-mail me about your success/failure soon, I may be forced to +start SINGING. And we don't want that, do we? + +(You know, it might be argued that I'm pushing this point a little too much. +If you think so, why not flame me in a quick little e-mail? Please also +include the type of card(s) you're using, software, size of network, and +whether it's working or not.) + +My e-mail address is: apenwarr@worldvisions.ca + + +--------------------------------------------------------------------------- + + +These are the ARCnet drivers for Linux. + + +This new release (2.91) has been put together by David Woodhouse +<dwmw2@infradead.org>, in an attempt to tidy up the driver after adding support +for yet another chipset. Now the generic support has been separated from the +individual chipset drivers, and the source files aren't quite so packed with +#ifdefs! I've changed this file a bit, but kept it in the first person from +Avery, because I didn't want to completely rewrite it. + +The previous release resulted from many months of on-and-off effort from me +(Avery Pennarun), many bug reports/fixes and suggestions from others, and in +particular a lot of input and coding from Tomasz Motylewski. Starting with +ARCnet 2.10 ALPHA, Tomasz's all-new-and-improved RFC1051 support has been +included and seems to be working fine! + + +Where do I discuss these drivers? +--------------------------------- + +Tomasz has been so kind as to set up a new and improved mailing list. +Subscribe by sending a message with the BODY "subscribe linux-arcnet YOUR +REAL NAME" to listserv@tichy.ch.uj.edu.pl. Then, to submit messages to the +list, mail to linux-arcnet@tichy.ch.uj.edu.pl. + +There are archives of the mailing list at: + http://epistolary.org/mailman/listinfo.cgi/arcnet + +The people on linux-net@vger.kernel.org (now defunct, replaced by +netdev@vger.kernel.org) have also been known to be very helpful, especially +when we're talking about ALPHA Linux kernels that may or may not work right +in the first place. + + +Other Drivers and Info +---------------------- + +You can try my ARCNET page on the World Wide Web at: + http://www.qis.net/~jschmitz/arcnet/ + +Also, SMC (one of the companies that makes ARCnet cards) has a WWW site you +might be interested in, which includes several drivers for various cards +including ARCnet. Try: + http://www.smc.com/ + +Performance Technologies makes various network software that supports +ARCnet: + http://www.perftech.com/ or ftp to ftp.perftech.com. + +Novell makes a networking stack for DOS which includes ARCnet drivers. Try +FTPing to ftp.novell.com. + +You can get the Crynwr packet driver collection (including arcether.com, the +one you'll want to use with ARCnet cards) from +oak.oakland.edu:/simtel/msdos/pktdrvr. It won't work perfectly on a 386+ +without patches, though, and also doesn't like several cards. Fixed +versions are available on my WWW page, or via e-mail if you don't have WWW +access. + + +Installing the Driver +--------------------- + +All you will need to do in order to install the driver is: + make config + (be sure to choose ARCnet in the network devices + and at least one chipset driver.) + make clean + make zImage + +If you obtained this ARCnet package as an upgrade to the ARCnet driver in +your current kernel, you will need to first copy arcnet.c over the one in +the linux/drivers/net directory. + +You will know the driver is installed properly if you get some ARCnet +messages when you reboot into the new Linux kernel. + +There are four chipset options: + + 1. Standard ARCnet COM90xx chipset. + +This is the normal ARCnet card, which you've probably got. This is the only +chipset driver which will autoprobe if not told where the card is. +It following options on the command line: + com90xx=[<io>[,<irq>[,<shmem>]]][,<name>] | <name> + +If you load the chipset support as a module, the options are: + io=<io> irq=<irq> shmem=<shmem> device=<name> + +To disable the autoprobe, just specify "com90xx=" on the kernel command line. +To specify the name alone, but allow autoprobe, just put "com90xx=<name>" + + 2. ARCnet COM20020 chipset. + +This is the new chipset from SMC with support for promiscuous mode (packet +sniffing), extra diagnostic information, etc. Unfortunately, there is no +sensible method of autoprobing for these cards. You must specify the I/O +address on the kernel command line. +The command line options are: + com20020=<io>[,<irq>[,<node_ID>[,backplane[,CKP[,timeout]]]]][,name] + +If you load the chipset support as a module, the options are: + io=<io> irq=<irq> node=<node_ID> backplane=<backplane> clock=<CKP> + timeout=<timeout> device=<name> + +The COM20020 chipset allows you to set the node ID in software, overriding the +default which is still set in DIP switches on the card. If you don't have the +COM20020 data sheets, and you don't know what the other three options refer +to, then they won't interest you - forget them. + + 3. ARCnet COM90xx chipset in IO-mapped mode. + +This will also work with the normal ARCnet cards, but doesn't use the shared +memory. It performs less well than the above driver, but is provided in case +you have a card which doesn't support shared memory, or (strangely) in case +you have so many ARCnet cards in your machine that you run out of shmem slots. +If you don't give the IO address on the kernel command line, then the driver +will not find the card. +The command line options are: + com90io=<io>[,<irq>][,<name>] + +If you load the chipset support as a module, the options are: + io=<io> irq=<irq> device=<name> + + 4. ARCnet RIM I cards. + +These are COM90xx chips which are _completely_ memory mapped. The support for +these is not tested. If you have one, please mail the author with a success +report. All options must be specified, except the device name. +Command line options: + arcrimi=<shmem>,<irq>,<node_ID>[,<name>] + +If you load the chipset support as a module, the options are: + shmem=<shmem> irq=<irq> node=<node_ID> device=<name> + + +Loadable Module Support +----------------------- + +Configure and rebuild Linux. When asked, answer 'm' to "Generic ARCnet +support" and to support for your ARCnet chipset if you want to use the +loadable module. You can also say 'y' to "Generic ARCnet support" and 'm' +to the chipset support if you wish. + + make config + make clean + make zImage + make modules + +If you're using a loadable module, you need to use insmod to load it, and +you can specify various characteristics of your card on the command +line. (In recent versions of the driver, autoprobing is much more reliable +and works as a module, so most of this is now unnecessary.) + +For example: + cd /usr/src/linux/modules + insmod arcnet.o + insmod com90xx.o + insmod com20020.o io=0x2e0 device=eth1 + + +Using the Driver +---------------- + +If you build your kernel with ARCnet COM90xx support included, it should +probe for your card automatically when you boot. If you use a different +chipset driver complied into the kernel, you must give the necessary options +on the kernel command line, as detailed above. + +Go read the NET-2-HOWTO and ETHERNET-HOWTO for Linux; they should be +available where you picked up this driver. Think of your ARCnet as a +souped-up (or down, as the case may be) Ethernet card. + +By the way, be sure to change all references from "eth0" to "arc0" in the +HOWTOs. Remember that ARCnet isn't a "true" Ethernet, and the device name +is DIFFERENT. + + +Multiple Cards in One Computer +------------------------------ + +Linux has pretty good support for this now, but since I've been busy, the +ARCnet driver has somewhat suffered in this respect. COM90xx support, if +compiled into the kernel, will (try to) autodetect all the installed cards. + +If you have other cards, with support compiled into the kernel, then you can +just repeat the options on the kernel command line, e.g.: +LILO: linux com20020=0x2e0 com20020=0x380 com90io=0x260 + +If you have the chipset support built as a loadable module, then you need to +do something like this: + insmod -o arc0 com90xx + insmod -o arc1 com20020 io=0x2e0 + insmod -o arc2 com90xx +The ARCnet drivers will now sort out their names automatically. + + +How do I get it to work with...? +-------------------------------- + +NFS: Should be fine linux->linux, just pretend you're using Ethernet cards. + oak.oakland.edu:/simtel/msdos/nfs has some nice DOS clients. There + is also a DOS-based NFS server called SOSS. It doesn't multitask + quite the way Linux does (actually, it doesn't multitask AT ALL) but + you never know what you might need. + + With AmiTCP (and possibly others), you may need to set the following + options in your Amiga nfstab: MD 1024 MR 1024 MW 1024 + (Thanks to Christian Gottschling <ferksy@indigo.tng.oche.de> + for this.) + + Probably these refer to maximum NFS data/read/write block sizes. I + don't know why the defaults on the Amiga didn't work; write to me if + you know more. + +DOS: If you're using the freeware arcether.com, you might want to install + the driver patch from my web page. It helps with PC/TCP, and also + can get arcether to load if it timed out too quickly during + initialization. In fact, if you use it on a 386+ you REALLY need + the patch, really. + +Windows: See DOS :) Trumpet Winsock works fine with either the Novell or + Arcether client, assuming you remember to load winpkt of course. + +LAN Manager and Windows for Workgroups: These programs use protocols that + are incompatible with the Internet standard. They try to pretend + the cards are Ethernet, and confuse everyone else on the network. + + However, v2.00 and higher of the Linux ARCnet driver supports this + protocol via the 'arc0e' device. See the section on "Multiprotocol + Support" for more information. + + Using the freeware Samba server and clients for Linux, you can now + interface quite nicely with TCP/IP-based WfWg or Lan Manager + networks. + +Windows 95: Tools are included with Win95 that let you use either the LANMAN + style network drivers (NDIS) or Novell drivers (ODI) to handle your + ARCnet packets. If you use ODI, you'll need to use the 'arc0' + device with Linux. If you use NDIS, then try the 'arc0e' device. + See the "Multiprotocol Support" section below if you need arc0e, + you're completely insane, and/or you need to build some kind of + hybrid network that uses both encapsulation types. + +OS/2: I've been told it works under Warp Connect with an ARCnet driver from + SMC. You need to use the 'arc0e' interface for this. If you get + the SMC driver to work with the TCP/IP stuff included in the + "normal" Warp Bonus Pack, let me know. + + ftp.microsoft.com also has a freeware "Lan Manager for OS/2" client + which should use the same protocol as WfWg does. I had no luck + installing it under Warp, however. Please mail me with any results. + +NetBSD/AmiTCP: These use an old version of the Internet standard ARCnet + protocol (RFC1051) which is compatible with the Linux driver v2.10 + ALPHA and above using the arc0s device. (See "Multiprotocol ARCnet" + below.) ** Newer versions of NetBSD apparently support RFC1201. + + +Using Multiprotocol ARCnet +-------------------------- + +The ARCnet driver v2.10 ALPHA supports three protocols, each on its own +"virtual network device": + + arc0 - RFC1201 protocol, the official Internet standard which just + happens to be 100% compatible with Novell's TRXNET driver. + Version 1.00 of the ARCnet driver supported _only_ this + protocol. arc0 is the fastest of the three protocols (for + whatever reason), and allows larger packets to be used + because it supports RFC1201 "packet splitting" operations. + Unless you have a specific need to use a different protocol, + I strongly suggest that you stick with this one. + + arc0e - "Ethernet-Encapsulation" which sends packets over ARCnet + that are actually a lot like Ethernet packets, including the + 6-byte hardware addresses. This protocol is compatible with + Microsoft's NDIS ARCnet driver, like the one in WfWg and + LANMAN. Because the MTU of 493 is actually smaller than the + one "required" by TCP/IP (576), there is a chance that some + network operations will not function properly. The Linux + TCP/IP layer can compensate in most cases, however, by + automatically fragmenting the TCP/IP packets to make them + fit. arc0e also works slightly more slowly than arc0, for + reasons yet to be determined. (Probably it's the smaller + MTU that does it.) + + arc0s - The "[s]imple" RFC1051 protocol is the "previous" Internet + standard that is completely incompatible with the new + standard. Some software today, however, continues to + support the old standard (and only the old standard) + including NetBSD and AmiTCP. RFC1051 also does not support + RFC1201's packet splitting, and the MTU of 507 is still + smaller than the Internet "requirement," so it's quite + possible that you may run into problems. It's also slower + than RFC1201 by about 25%, for the same reason as arc0e. + + The arc0s support was contributed by Tomasz Motylewski + and modified somewhat by me. Bugs are probably my fault. + +You can choose not to compile arc0e and arc0s into the driver if you want - +this will save you a bit of memory and avoid confusion when eg. trying to +use the "NFS-root" stuff in recent Linux kernels. + +The arc0e and arc0s devices are created automatically when you first +ifconfig the arc0 device. To actually use them, though, you need to also +ifconfig the other virtual devices you need. There are a number of ways you +can set up your network then: + + +1. Single Protocol. + + This is the simplest way to configure your network: use just one of the + two available protocols. As mentioned above, it's a good idea to use + only arc0 unless you have a good reason (like some other software, ie. + WfWg, that only works with arc0e). + + If you need only arc0, then the following commands should get you going: + ifconfig arc0 MY.IP.ADD.RESS + route add MY.IP.ADD.RESS arc0 + route add -net SUB.NET.ADD.RESS arc0 + [add other local routes here] + + If you need arc0e (and only arc0e), it's a little different: + ifconfig arc0 MY.IP.ADD.RESS + ifconfig arc0e MY.IP.ADD.RESS + route add MY.IP.ADD.RESS arc0e + route add -net SUB.NET.ADD.RESS arc0e + + arc0s works much the same way as arc0e. + + +2. More than one protocol on the same wire. + + Now things start getting confusing. To even try it, you may need to be + partly crazy. Here's what *I* did. :) Note that I don't include arc0s in + my home network; I don't have any NetBSD or AmiTCP computers, so I only + use arc0s during limited testing. + + I have three computers on my home network; two Linux boxes (which prefer + RFC1201 protocol, for reasons listed above), and one XT that can't run + Linux but runs the free Microsoft LANMAN Client instead. + + Worse, one of the Linux computers (freedom) also has a modem and acts as + a router to my Internet provider. The other Linux box (insight) also has + its own IP address and needs to use freedom as its default gateway. The + XT (patience), however, does not have its own Internet IP address and so + I assigned it one on a "private subnet" (as defined by RFC1597). + + To start with, take a simple network with just insight and freedom. + Insight needs to: + - talk to freedom via RFC1201 (arc0) protocol, because I like it + more and it's faster. + - use freedom as its Internet gateway. + + That's pretty easy to do. Set up insight like this: + ifconfig arc0 insight + route add insight arc0 + route add freedom arc0 /* I would use the subnet here (like I said + to to in "single protocol" above), + but the rest of the subnet + unfortunately lies across the PPP + link on freedom, which confuses + things. */ + route add default gw freedom + + And freedom gets configured like so: + ifconfig arc0 freedom + route add freedom arc0 + route add insight arc0 + /* and default gateway is configured by pppd */ + + Great, now insight talks to freedom directly on arc0, and sends packets + to the Internet through freedom. If you didn't know how to do the above, + you should probably stop reading this section now because it only gets + worse. + + Now, how do I add patience into the network? It will be using LANMAN + Client, which means I need the arc0e device. It needs to be able to talk + to both insight and freedom, and also use freedom as a gateway to the + Internet. (Recall that patience has a "private IP address" which won't + work on the Internet; that's okay, I configured Linux IP masquerading on + freedom for this subnet). + + So patience (necessarily; I don't have another IP number from my + provider) has an IP address on a different subnet than freedom and + insight, but needs to use freedom as an Internet gateway. Worse, most + DOS networking programs, including LANMAN, have braindead networking + schemes that rely completely on the netmask and a 'default gateway' to + determine how to route packets. This means that to get to freedom or + insight, patience WILL send through its default gateway, regardless of + the fact that both freedom and insight (courtesy of the arc0e device) + could understand a direct transmission. + + I compensate by giving freedom an extra IP address - aliased 'gatekeeper' + - that is on my private subnet, the same subnet that patience is on. I + then define gatekeeper to be the default gateway for patience. + + To configure freedom (in addition to the commands above): + ifconfig arc0e gatekeeper + route add gatekeeper arc0e + route add patience arc0e + + This way, freedom will send all packets for patience through arc0e, + giving its IP address as gatekeeper (on the private subnet). When it + talks to insight or the Internet, it will use its "freedom" Internet IP + address. + + You will notice that we haven't configured the arc0e device on insight. + This would work, but is not really necessary, and would require me to + assign insight another special IP number from my private subnet. Since + both insight and patience are using freedom as their default gateway, the + two can already talk to each other. + + It's quite fortunate that I set things up like this the first time (cough + cough) because it's really handy when I boot insight into DOS. There, it + runs the Novell ODI protocol stack, which only works with RFC1201 ARCnet. + In this mode it would be impossible for insight to communicate directly + with patience, since the Novell stack is incompatible with Microsoft's + Ethernet-Encap. Without changing any settings on freedom or patience, I + simply set freedom as the default gateway for insight (now in DOS, + remember) and all the forwarding happens "automagically" between the two + hosts that would normally not be able to communicate at all. + + For those who like diagrams, I have created two "virtual subnets" on the + same physical ARCnet wire. You can picture it like this: + + + [RFC1201 NETWORK] [ETHER-ENCAP NETWORK] + (registered Internet subnet) (RFC1597 private subnet) + + (IP Masquerade) + /---------------\ * /---------------\ + | | * | | + | +-Freedom-*-Gatekeeper-+ | + | | | * | | + \-------+-------/ | * \-------+-------/ + | | | + Insight | Patience + (Internet) + + + +It works: what now? +------------------- + +Send mail describing your setup, preferably including driver version, kernel +version, ARCnet card model, CPU type, number of systems on your network, and +list of software in use to me at the following address: + apenwarr@worldvisions.ca + +I do send (sometimes automated) replies to all messages I receive. My email +can be weird (and also usually gets forwarded all over the place along the +way to me), so if you don't get a reply within a reasonable time, please +resend. + + +It doesn't work: what now? +-------------------------- + +Do the same as above, but also include the output of the ifconfig and route +commands, as well as any pertinent log entries (ie. anything that starts +with "arcnet:" and has shown up since the last reboot) in your mail. + +If you want to try fixing it yourself (I strongly recommend that you mail me +about the problem first, since it might already have been solved) you may +want to try some of the debug levels available. For heavy testing on +D_DURING or more, it would be a REALLY good idea to kill your klogd daemon +first! D_DURING displays 4-5 lines for each packet sent or received. D_TX, +D_RX, and D_SKB actually DISPLAY each packet as it is sent or received, +which is obviously quite big. + +Starting with v2.40 ALPHA, the autoprobe routines have changed +significantly. In particular, they won't tell you why the card was not +found unless you turn on the D_INIT_REASONS debugging flag. + +Once the driver is running, you can run the arcdump shell script (available +from me or in the full ARCnet package, if you have it) as root to list the +contents of the arcnet buffers at any time. To make any sense at all out of +this, you should grab the pertinent RFCs. (some are listed near the top of +arcnet.c). arcdump assumes your card is at 0xD0000. If it isn't, edit the +script. + +Buffers 0 and 1 are used for receiving, and Buffers 2 and 3 are for sending. +Ping-pong buffers are implemented both ways. + +If your debug level includes D_DURING and you did NOT define SLOW_XMIT_COPY, +the buffers are cleared to a constant value of 0x42 every time the card is +reset (which should only happen when you do an ifconfig up, or when Linux +decides that the driver is broken). During a transmit, unused parts of the +buffer will be cleared to 0x42 as well. This is to make it easier to figure +out which bytes are being used by a packet. + +You can change the debug level without recompiling the kernel by typing: + ifconfig arc0 down metric 1xxx + /etc/rc.d/rc.inet1 +where "xxx" is the debug level you want. For example, "metric 1015" would put +you at debug level 15. Debug level 7 is currently the default. + +Note that the debug level is (starting with v1.90 ALPHA) a binary +combination of different debug flags; so debug level 7 is really 1+2+4 or +D_NORMAL+D_EXTRA+D_INIT. To include D_DURING, you would add 16 to this, +resulting in debug level 23. + +If you don't understand that, you probably don't want to know anyway. +E-mail me about your problem. + + +I want to send money: what now? +------------------------------- + +Go take a nap or something. You'll feel better in the morning. |