summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/i2c/busses
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/i2c/busses')
-rw-r--r--kernel/Documentation/i2c/busses/i2c-ali153542
-rw-r--r--kernel/Documentation/i2c/busses/i2c-ali156327
-rw-r--r--kernel/Documentation/i2c/busses/i2c-ali15x3112
-rw-r--r--kernel/Documentation/i2c/busses/i2c-amd75625
-rw-r--r--kernel/Documentation/i2c/busses/i2c-amd811141
-rw-r--r--kernel/Documentation/i2c/busses/i2c-diolan-u2c26
-rw-r--r--kernel/Documentation/i2c/busses/i2c-i801164
-rw-r--r--kernel/Documentation/i2c/busses/i2c-ismt36
-rw-r--r--kernel/Documentation/i2c/busses/i2c-nforce250
-rw-r--r--kernel/Documentation/i2c/busses/i2c-ocores68
-rw-r--r--kernel/Documentation/i2c/busses/i2c-parport177
-rw-r--r--kernel/Documentation/i2c/busses/i2c-parport-light22
-rw-r--r--kernel/Documentation/i2c/busses/i2c-pca-isa23
-rw-r--r--kernel/Documentation/i2c/busses/i2c-piix4110
-rw-r--r--kernel/Documentation/i2c/busses/i2c-sis559559
-rw-r--r--kernel/Documentation/i2c/busses/i2c-sis63058
-rw-r--r--kernel/Documentation/i2c/busses/i2c-sis96x73
-rw-r--r--kernel/Documentation/i2c/busses/i2c-taos-evm46
-rw-r--r--kernel/Documentation/i2c/busses/i2c-via34
-rw-r--r--kernel/Documentation/i2c/busses/i2c-viapro73
-rw-r--r--kernel/Documentation/i2c/busses/scx200_acb32
21 files changed, 1298 insertions, 0 deletions
diff --git a/kernel/Documentation/i2c/busses/i2c-ali1535 b/kernel/Documentation/i2c/busses/i2c-ali1535
new file mode 100644
index 000000000..5d46342e4
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-ali1535
@@ -0,0 +1,42 @@
+Kernel driver i2c-ali1535
+
+Supported adapters:
+ * Acer Labs, Inc. ALI 1535 (south bridge)
+ Datasheet: Now under NDA
+ http://www.ali.com.tw/
+
+Authors:
+ Frodo Looijaard <frodol@dds.nl>,
+ Philip Edelbrock <phil@netroedge.com>,
+ Mark D. Studebaker <mdsxyz123@yahoo.com>,
+ Dan Eaton <dan.eaton@rocketlogix.com>,
+ Stephen Rousset<stephen.rousset@rocketlogix.com>
+
+Description
+-----------
+
+This is the driver for the SMB Host controller on Acer Labs Inc. (ALI)
+M1535 South Bridge.
+
+The M1535 is a South bridge for portable systems. It is very similar to the
+M15x3 South bridges also produced by Acer Labs Inc. Some of the registers
+within the part have moved and some have been redefined slightly.
+Additionally, the sequencing of the SMBus transactions has been modified to
+be more consistent with the sequencing recommended by the manufacturer and
+observed through testing. These changes are reflected in this driver and
+can be identified by comparing this driver to the i2c-ali15x3 driver. For
+an overview of these chips see http://www.acerlabs.com
+
+The SMB controller is part of the M7101 device, which is an ACPI-compliant
+Power Management Unit (PMU).
+
+The whole M7101 device has to be enabled for the SMB to work. You can't
+just enable the SMB alone. The SMB and the ACPI have separate I/O spaces.
+We make sure that the SMB is enabled. We leave the ACPI alone.
+
+
+Features
+--------
+
+This driver controls the SMB Host only. This driver does not use
+interrupts.
diff --git a/kernel/Documentation/i2c/busses/i2c-ali1563 b/kernel/Documentation/i2c/busses/i2c-ali1563
new file mode 100644
index 000000000..41b1a077e
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-ali1563
@@ -0,0 +1,27 @@
+Kernel driver i2c-ali1563
+
+Supported adapters:
+ * Acer Labs, Inc. ALI 1563 (south bridge)
+ Datasheet: Now under NDA
+ http://www.ali.com.tw/
+
+Author: Patrick Mochel <mochel@digitalimplant.org>
+
+Description
+-----------
+
+This is the driver for the SMB Host controller on Acer Labs Inc. (ALI)
+M1563 South Bridge.
+
+For an overview of these chips see http://www.acerlabs.com
+
+The M1563 southbridge is deceptively similar to the M1533, with a few
+notable exceptions. One of those happens to be the fact they upgraded the
+i2c core to be SMBus 2.0 compliant, and happens to be almost identical to
+the i2c controller found in the Intel 801 south bridges.
+
+Features
+--------
+
+This driver controls the SMB Host only. This driver does not use
+interrupts.
diff --git a/kernel/Documentation/i2c/busses/i2c-ali15x3 b/kernel/Documentation/i2c/busses/i2c-ali15x3
new file mode 100644
index 000000000..42888d8ac
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-ali15x3
@@ -0,0 +1,112 @@
+Kernel driver i2c-ali15x3
+
+Supported adapters:
+ * Acer Labs, Inc. ALI 1533 and 1543C (south bridge)
+ Datasheet: Now under NDA
+ http://www.ali.com.tw/
+
+Authors:
+ Frodo Looijaard <frodol@dds.nl>,
+ Philip Edelbrock <phil@netroedge.com>,
+ Mark D. Studebaker <mdsxyz123@yahoo.com>
+
+Module Parameters
+-----------------
+
+* force_addr: int
+ Initialize the base address of the i2c controller
+
+
+Notes
+-----
+
+The force_addr parameter is useful for boards that don't set the address in
+the BIOS. Does not do a PCI force; the device must still be present in
+lspci. Don't use this unless the driver complains that the base address is
+not set.
+
+Example: 'modprobe i2c-ali15x3 force_addr=0xe800'
+
+SMBus periodically hangs on ASUS P5A motherboards and can only be cleared
+by a power cycle. Cause unknown (see Issues below).
+
+
+Description
+-----------
+
+This is the driver for the SMB Host controller on Acer Labs Inc. (ALI)
+M1541 and M1543C South Bridges.
+
+The M1543C is a South bridge for desktop systems.
+The M1541 is a South bridge for portable systems.
+They are part of the following ALI chipsets:
+
+ * "Aladdin Pro 2" includes the M1621 Slot 1 North bridge with AGP and
+ 100MHz CPU Front Side bus
+ * "Aladdin V" includes the M1541 Socket 7 North bridge with AGP and 100MHz
+ CPU Front Side bus
+ Some Aladdin V motherboards:
+ Asus P5A
+ Atrend ATC-5220
+ BCM/GVC VP1541
+ Biostar M5ALA
+ Gigabyte GA-5AX (** Generally doesn't work because the BIOS doesn't
+ enable the 7101 device! **)
+ Iwill XA100 Plus
+ Micronics C200
+ Microstar (MSI) MS-5169
+
+ * "Aladdin IV" includes the M1541 Socket 7 North bridge
+ with host bus up to 83.3 MHz.
+
+For an overview of these chips see http://www.acerlabs.com. At this time the
+full data sheets on the web site are password protected, however if you
+contact the ALI office in San Jose they may give you the password.
+
+The M1533/M1543C devices appear as FOUR separate devices on the PCI bus. An
+output of lspci will show something similar to the following:
+
+ 00:02.0 USB Controller: Acer Laboratories Inc. M5237 (rev 03)
+ 00:03.0 Bridge: Acer Laboratories Inc. M7101 <= THIS IS THE ONE WE NEED
+ 00:07.0 ISA bridge: Acer Laboratories Inc. M1533 (rev c3)
+ 00:0f.0 IDE interface: Acer Laboratories Inc. M5229 (rev c1)
+
+** IMPORTANT **
+** If you have a M1533 or M1543C on the board and you get
+** "ali15x3: Error: Can't detect ali15x3!"
+** then run lspci.
+** If you see the 1533 and 5229 devices but NOT the 7101 device,
+** then you must enable ACPI, the PMU, SMB, or something similar
+** in the BIOS.
+** The driver won't work if it can't find the M7101 device.
+
+The SMB controller is part of the M7101 device, which is an ACPI-compliant
+Power Management Unit (PMU).
+
+The whole M7101 device has to be enabled for the SMB to work. You can't
+just enable the SMB alone. The SMB and the ACPI have separate I/O spaces.
+We make sure that the SMB is enabled. We leave the ACPI alone.
+
+Features
+--------
+
+This driver controls the SMB Host only. The SMB Slave
+controller on the M15X3 is not enabled. This driver does not use
+interrupts.
+
+
+Issues
+------
+
+This driver requests the I/O space for only the SMB
+registers. It doesn't use the ACPI region.
+
+On the ASUS P5A motherboard, there are several reports that
+the SMBus will hang and this can only be resolved by
+powering off the computer. It appears to be worse when the board
+gets hot, for example under heavy CPU load, or in the summer.
+There may be electrical problems on this board.
+On the P5A, the W83781D sensor chip is on both the ISA and
+SMBus. Therefore the SMBus hangs can generally be avoided
+by accessing the W83781D on the ISA bus only.
+
diff --git a/kernel/Documentation/i2c/busses/i2c-amd756 b/kernel/Documentation/i2c/busses/i2c-amd756
new file mode 100644
index 000000000..67f30874d
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-amd756
@@ -0,0 +1,25 @@
+Kernel driver i2c-amd756
+
+Supported adapters:
+ * AMD 756
+ * AMD 766
+ * AMD 768
+ * AMD 8111
+ Datasheets: Publicly available on AMD website
+
+ * nVidia nForce
+ Datasheet: Unavailable
+
+Authors:
+ Frodo Looijaard <frodol@dds.nl>,
+ Philip Edelbrock <phil@netroedge.com>
+
+Description
+-----------
+
+This driver supports the AMD 756, 766, 768 and 8111 Peripheral Bus
+Controllers, and the nVidia nForce.
+
+Note that for the 8111, there are two SMBus adapters. The SMBus 1.0 adapter
+is supported by this driver, and the SMBus 2.0 adapter is supported by the
+i2c-amd8111 driver.
diff --git a/kernel/Documentation/i2c/busses/i2c-amd8111 b/kernel/Documentation/i2c/busses/i2c-amd8111
new file mode 100644
index 000000000..460dd6635
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-amd8111
@@ -0,0 +1,41 @@
+Kernel driver i2c-adm8111
+
+Supported adapters:
+ * AMD-8111 SMBus 2.0 PCI interface
+
+Datasheets:
+ AMD datasheet not yet available, but almost everything can be found
+ in the publicly available ACPI 2.0 specification, which the adapter
+ follows.
+
+Author: Vojtech Pavlik <vojtech@suse.cz>
+
+Description
+-----------
+
+If you see something like this:
+
+00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
+ Subsystem: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0
+ Flags: medium devsel, IRQ 19
+ I/O ports at d400 [size=32]
+
+in your 'lspci -v', then this driver is for your chipset.
+
+Process Call Support
+--------------------
+
+Supported.
+
+SMBus 2.0 Support
+-----------------
+
+Supported. Both PEC and block process call support is implemented. Slave
+mode or host notification are not yet implemented.
+
+Notes
+-----
+
+Note that for the 8111, there are two SMBus adapters. The SMBus 2.0 adapter
+is supported by this driver, and the SMBus 1.0 adapter is supported by the
+i2c-amd756 driver.
diff --git a/kernel/Documentation/i2c/busses/i2c-diolan-u2c b/kernel/Documentation/i2c/busses/i2c-diolan-u2c
new file mode 100644
index 000000000..0d6018c31
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-diolan-u2c
@@ -0,0 +1,26 @@
+Kernel driver i2c-diolan-u2c
+
+Supported adapters:
+ * Diolan U2C-12 I2C-USB adapter
+ Documentation:
+ http://www.diolan.com/i2c/u2c12.html
+
+Author: Guenter Roeck <linux@roeck-us.net>
+
+Description
+-----------
+
+This is the driver for the Diolan U2C-12 USB-I2C adapter.
+
+The Diolan U2C-12 I2C-USB Adapter provides a low cost solution to connect
+a computer to I2C slave devices using a USB interface. It also supports
+connectivity to SPI devices.
+
+This driver only supports the I2C interface of U2C-12. The driver does not use
+interrupts.
+
+
+Module parameters
+-----------------
+
+* frequency: I2C bus frequency
diff --git a/kernel/Documentation/i2c/busses/i2c-i801 b/kernel/Documentation/i2c/busses/i2c-i801
new file mode 100644
index 000000000..82f48f774
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-i801
@@ -0,0 +1,164 @@
+Kernel driver i2c-i801
+
+Supported adapters:
+ * Intel 82801AA and 82801AB (ICH and ICH0 - part of the
+ '810' and '810E' chipsets)
+ * Intel 82801BA (ICH2 - part of the '815E' chipset)
+ * Intel 82801CA/CAM (ICH3)
+ * Intel 82801DB (ICH4) (HW PEC supported)
+ * Intel 82801EB/ER (ICH5) (HW PEC supported)
+ * Intel 6300ESB
+ * Intel 82801FB/FR/FW/FRW (ICH6)
+ * Intel 82801G (ICH7)
+ * Intel 631xESB/632xESB (ESB2)
+ * Intel 82801H (ICH8)
+ * Intel 82801I (ICH9)
+ * Intel EP80579 (Tolapai)
+ * Intel 82801JI (ICH10)
+ * Intel 5/3400 Series (PCH)
+ * Intel 6 Series (PCH)
+ * Intel Patsburg (PCH)
+ * Intel DH89xxCC (PCH)
+ * Intel Panther Point (PCH)
+ * Intel Lynx Point (PCH)
+ * Intel Lynx Point-LP (PCH)
+ * Intel Avoton (SOC)
+ * Intel Wellsburg (PCH)
+ * Intel Coleto Creek (PCH)
+ * Intel Wildcat Point (PCH)
+ * Intel Wildcat Point-LP (PCH)
+ * Intel BayTrail (SOC)
+ * Intel Sunrise Point-H (PCH)
+ * Intel Sunrise Point-LP (PCH)
+ Datasheets: Publicly available at the Intel website
+
+On Intel Patsburg and later chipsets, both the normal host SMBus controller
+and the additional 'Integrated Device Function' controllers are supported.
+
+Authors:
+ Mark Studebaker <mdsxyz123@yahoo.com>
+ Jean Delvare <jdelvare@suse.de>
+
+
+Module Parameters
+-----------------
+
+* disable_features (bit vector)
+Disable selected features normally supported by the device. This makes it
+possible to work around possible driver or hardware bugs if the feature in
+question doesn't work as intended for whatever reason. Bit values:
+ 0x01 disable SMBus PEC
+ 0x02 disable the block buffer
+ 0x08 disable the I2C block read functionality
+ 0x10 don't use interrupts
+
+
+Description
+-----------
+
+The ICH (properly known as the 82801AA), ICH0 (82801AB), ICH2 (82801BA),
+ICH3 (82801CA/CAM) and later devices (PCH) are Intel chips that are a part of
+Intel's '810' chipset for Celeron-based PCs, '810E' chipset for
+Pentium-based PCs, '815E' chipset, and others.
+
+The ICH chips contain at least SEVEN separate PCI functions in TWO logical
+PCI devices. An output of lspci will show something similar to the
+following:
+
+ 00:1e.0 PCI bridge: Intel Corporation: Unknown device 2418 (rev 01)
+ 00:1f.0 ISA bridge: Intel Corporation: Unknown device 2410 (rev 01)
+ 00:1f.1 IDE interface: Intel Corporation: Unknown device 2411 (rev 01)
+ 00:1f.2 USB Controller: Intel Corporation: Unknown device 2412 (rev 01)
+ 00:1f.3 Unknown class [0c05]: Intel Corporation: Unknown device 2413 (rev 01)
+
+The SMBus controller is function 3 in device 1f. Class 0c05 is SMBus Serial
+Controller.
+
+The ICH chips are quite similar to Intel's PIIX4 chip, at least in the
+SMBus controller.
+
+
+Process Call Support
+--------------------
+
+Not supported.
+
+
+I2C Block Read Support
+----------------------
+
+I2C block read is supported on the 82801EB (ICH5) and later chips.
+
+
+SMBus 2.0 Support
+-----------------
+
+The 82801DB (ICH4) and later chips support several SMBus 2.0 features.
+
+
+Interrupt Support
+-----------------
+
+PCI interrupt support is supported on the 82801EB (ICH5) and later chips.
+
+
+Hidden ICH SMBus
+----------------
+
+If your system has an Intel ICH south bridge, but you do NOT see the
+SMBus device at 00:1f.3 in lspci, and you can't figure out any way in the
+BIOS to enable it, it means it has been hidden by the BIOS code. Asus is
+well known for first doing this on their P4B motherboard, and many other
+boards after that. Some vendor machines are affected as well.
+
+The first thing to try is the "i2c_ec" ACPI driver. It could be that the
+SMBus was hidden on purpose because it'll be driven by ACPI. If the
+i2c_ec driver works for you, just forget about the i2c-i801 driver and
+don't try to unhide the ICH SMBus. Even if i2c_ec doesn't work, you
+better make sure that the SMBus isn't used by the ACPI code. Try loading
+the "fan" and "thermal" drivers, and check in /proc/acpi/fan and
+/proc/acpi/thermal_zone. If you find anything there, it's likely that
+the ACPI is accessing the SMBus and it's safer not to unhide it. Only
+once you are certain that ACPI isn't using the SMBus, you can attempt
+to unhide it.
+
+In order to unhide the SMBus, we need to change the value of a PCI
+register before the kernel enumerates the PCI devices. This is done in
+drivers/pci/quirks.c, where all affected boards must be listed (see
+function asus_hides_smbus_hostbridge.) If the SMBus device is missing,
+and you think there's something interesting on the SMBus (e.g. a
+hardware monitoring chip), you need to add your board to the list.
+
+The motherboard is identified using the subvendor and subdevice IDs of the
+host bridge PCI device. Get yours with "lspci -n -v -s 00:00.0":
+
+00:00.0 Class 0600: 8086:2570 (rev 02)
+ Subsystem: 1043:80f2
+ Flags: bus master, fast devsel, latency 0
+ Memory at fc000000 (32-bit, prefetchable) [size=32M]
+ Capabilities: [e4] #09 [2106]
+ Capabilities: [a0] AGP version 3.0
+
+Here the host bridge ID is 2570 (82865G/PE/P), the subvendor ID is 1043
+(Asus) and the subdevice ID is 80f2 (P4P800-X). You can find the symbolic
+names for the bridge ID and the subvendor ID in include/linux/pci_ids.h,
+and then add a case for your subdevice ID at the right place in
+drivers/pci/quirks.c. Then please give it very good testing, to make sure
+that the unhidden SMBus doesn't conflict with e.g. ACPI.
+
+If it works, proves useful (i.e. there are usable chips on the SMBus)
+and seems safe, please submit a patch for inclusion into the kernel.
+
+Note: There's a useful script in lm_sensors 2.10.2 and later, named
+unhide_ICH_SMBus (in prog/hotplug), which uses the fakephp driver to
+temporarily unhide the SMBus without having to patch and recompile your
+kernel. It's very convenient if you just want to check if there's
+anything interesting on your hidden ICH SMBus.
+
+
+**********************
+The lm_sensors project gratefully acknowledges the support of Texas
+Instruments in the initial development of this driver.
+
+The lm_sensors project gratefully acknowledges the support of Intel in the
+development of SMBus 2.0 / ICH4 features of this driver.
diff --git a/kernel/Documentation/i2c/busses/i2c-ismt b/kernel/Documentation/i2c/busses/i2c-ismt
new file mode 100644
index 000000000..737355822
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-ismt
@@ -0,0 +1,36 @@
+Kernel driver i2c-ismt
+
+Supported adapters:
+ * Intel S12xx series SOCs
+
+Authors:
+ Bill Brown <bill.e.brown@intel.com>
+
+
+Module Parameters
+-----------------
+
+* bus_speed (unsigned int)
+Allows changing of the bus speed. Normally, the bus speed is set by the BIOS
+and never needs to be changed. However, some SMBus analyzers are too slow for
+monitoring the bus during debug, thus the need for this module parameter.
+Specify the bus speed in kHz.
+Available bus frequency settings:
+ 0 no change
+ 80 kHz
+ 100 kHz
+ 400 kHz
+ 1000 kHz
+
+
+Description
+-----------
+
+The S12xx series of SOCs have a pair of integrated SMBus 2.0 controllers
+targeted primarily at the microserver and storage markets.
+
+The S12xx series contain a pair of PCI functions. An output of lspci will show
+something similar to the following:
+
+ 00:13.0 System peripheral: Intel Corporation Centerton SMBus 2.0 Controller 0
+ 00:13.1 System peripheral: Intel Corporation Centerton SMBus 2.0 Controller 1
diff --git a/kernel/Documentation/i2c/busses/i2c-nforce2 b/kernel/Documentation/i2c/busses/i2c-nforce2
new file mode 100644
index 000000000..9698c396b
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-nforce2
@@ -0,0 +1,50 @@
+Kernel driver i2c-nforce2
+
+Supported adapters:
+ * nForce2 MCP 10de:0064
+ * nForce2 Ultra 400 MCP 10de:0084
+ * nForce3 Pro150 MCP 10de:00D4
+ * nForce3 250Gb MCP 10de:00E4
+ * nForce4 MCP 10de:0052
+ * nForce4 MCP-04 10de:0034
+ * nForce MCP51 10de:0264
+ * nForce MCP55 10de:0368
+ * nForce MCP61 10de:03EB
+ * nForce MCP65 10de:0446
+ * nForce MCP67 10de:0542
+ * nForce MCP73 10de:07D8
+ * nForce MCP78S 10de:0752
+ * nForce MCP79 10de:0AA2
+
+Datasheet: not publicly available, but seems to be similar to the
+ AMD-8111 SMBus 2.0 adapter.
+
+Authors:
+ Hans-Frieder Vogt <hfvogt@gmx.net>,
+ Thomas Leibold <thomas@plx.com>,
+ Patrick Dreker <patrick@dreker.de>
+
+Description
+-----------
+
+i2c-nforce2 is a driver for the SMBuses included in the nVidia nForce2 MCP.
+
+If your 'lspci -v' listing shows something like the following,
+
+00:01.1 SMBus: nVidia Corporation: Unknown device 0064 (rev a2)
+ Subsystem: Asustek Computer, Inc.: Unknown device 0c11
+ Flags: 66Mhz, fast devsel, IRQ 5
+ I/O ports at c000 [size=32]
+ Capabilities: <available only to root>
+
+then this driver should support the SMBuses of your motherboard.
+
+
+Notes
+-----
+
+The SMBus adapter in the nForce2 chipset seems to be very similar to the
+SMBus 2.0 adapter in the AMD-8111 south bridge. However, I could only get
+the driver to work with direct I/O access, which is different to the EC
+interface of the AMD-8111. Tested on Asus A7N8X. The ACPI DSDT table of the
+Asus A7N8X lists two SMBuses, both of which are supported by this driver.
diff --git a/kernel/Documentation/i2c/busses/i2c-ocores b/kernel/Documentation/i2c/busses/i2c-ocores
new file mode 100644
index 000000000..c269aaa2f
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-ocores
@@ -0,0 +1,68 @@
+Kernel driver i2c-ocores
+
+Supported adapters:
+ * OpenCores.org I2C controller by Richard Herveille (see datasheet link)
+ Datasheet: http://www.opencores.org/projects.cgi/web/i2c/overview
+
+Author: Peter Korsgaard <jacmet@sunsite.dk>
+
+Description
+-----------
+
+i2c-ocores is an i2c bus driver for the OpenCores.org I2C controller
+IP core by Richard Herveille.
+
+Usage
+-----
+
+i2c-ocores uses the platform bus, so you need to provide a struct
+platform_device with the base address and interrupt number. The
+dev.platform_data of the device should also point to a struct
+ocores_i2c_platform_data (see linux/i2c-ocores.h) describing the
+distance between registers and the input clock speed.
+There is also a possibility to attach a list of i2c_board_info which
+the i2c-ocores driver will add to the bus upon creation.
+
+E.G. something like:
+
+static struct resource ocores_resources[] = {
+ [0] = {
+ .start = MYI2C_BASEADDR,
+ .end = MYI2C_BASEADDR + 8,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = MYI2C_IRQ,
+ .end = MYI2C_IRQ,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+/* optional board info */
+struct i2c_board_info ocores_i2c_board_info[] = {
+ {
+ I2C_BOARD_INFO("tsc2003", 0x48),
+ .platform_data = &tsc2003_platform_data,
+ .irq = TSC_IRQ
+ },
+ {
+ I2C_BOARD_INFO("adv7180", 0x42 >> 1),
+ .irq = ADV_IRQ
+ }
+};
+
+static struct ocores_i2c_platform_data myi2c_data = {
+ .regstep = 2, /* two bytes between registers */
+ .clock_khz = 50000, /* input clock of 50MHz */
+ .devices = ocores_i2c_board_info, /* optional table of devices */
+ .num_devices = ARRAY_SIZE(ocores_i2c_board_info), /* table size */
+};
+
+static struct platform_device myi2c = {
+ .name = "ocores-i2c",
+ .dev = {
+ .platform_data = &myi2c_data,
+ },
+ .num_resources = ARRAY_SIZE(ocores_resources),
+ .resource = ocores_resources,
+};
diff --git a/kernel/Documentation/i2c/busses/i2c-parport b/kernel/Documentation/i2c/busses/i2c-parport
new file mode 100644
index 000000000..0e2d17b46
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-parport
@@ -0,0 +1,177 @@
+Kernel driver i2c-parport
+
+Author: Jean Delvare <jdelvare@suse.de>
+
+This is a unified driver for several i2c-over-parallel-port adapters,
+such as the ones made by Philips, Velleman or ELV. This driver is
+meant as a replacement for the older, individual drivers:
+ * i2c-philips-par
+ * i2c-elv
+ * i2c-velleman
+ * video/i2c-parport (NOT the same as this one, dedicated to home brew
+ teletext adapters)
+
+It currently supports the following devices:
+ * (type=0) Philips adapter
+ * (type=1) home brew teletext adapter
+ * (type=2) Velleman K8000 adapter
+ * (type=3) ELV adapter
+ * (type=4) Analog Devices ADM1032 evaluation board
+ * (type=5) Analog Devices evaluation boards: ADM1025, ADM1030, ADM1031
+ * (type=6) Barco LPT->DVI (K5800236) adapter
+ * (type=7) One For All JP1 parallel port adapter
+
+These devices use different pinout configurations, so you have to tell
+the driver what you have, using the type module parameter. There is no
+way to autodetect the devices. Support for different pinout configurations
+can be easily added when needed.
+
+Earlier kernels defaulted to type=0 (Philips). But now, if the type
+parameter is missing, the driver will simply fail to initialize.
+
+SMBus alert support is available on adapters which have this line properly
+connected to the parallel port's interrupt pin.
+
+
+Building your own adapter
+-------------------------
+
+If you want to build you own i2c-over-parallel-port adapter, here is
+a sample electronics schema (credits go to Sylvain Munaut):
+
+Device PC
+Side ___________________Vdd (+) Side
+ | | |
+ --- --- ---
+ | | | | | |
+ |R| |R| |R|
+ | | | | | |
+ --- --- ---
+ | | |
+ | | /| |
+SCL ----------x--------o |-----------x------------------- pin 2
+ | \| | |
+ | | |
+ | |\ | |
+SDA ----------x----x---| o---x--------------------------- pin 13
+ | |/ |
+ | |
+ | /| |
+ ---------o |----------------x-------------- pin 3
+ \| | |
+ | |
+ --- ---
+ | | | |
+ |R| |R|
+ | | | |
+ --- ---
+ | |
+ ### ###
+ GND GND
+
+Remarks:
+ - This is the exact pinout and electronics used on the Analog Devices
+ evaluation boards.
+ /|
+ - All inverters -o |- must be 74HC05, they must be open collector output.
+ \|
+ - All resitors are 10k.
+ - Pins 18-25 of the parallel port connected to GND.
+ - Pins 4-9 (D2-D7) could be used as VDD is the driver drives them high.
+ The ADM1032 evaluation board uses D4-D7. Beware that the amount of
+ current you can draw from the parallel port is limited. Also note that
+ all connected lines MUST BE driven at the same state, else you'll short
+ circuit the output buffers! So plugging the I2C adapter after loading
+ the i2c-parport module might be a good safety since data line state
+ prior to init may be unknown.
+ - This is 5V!
+ - Obviously you cannot read SCL (so it's not really standard-compliant).
+ Pretty easy to add, just copy the SDA part and use another input pin.
+ That would give (ELV compatible pinout):
+
+
+Device PC
+Side ______________________________Vdd (+) Side
+ | | | |
+ --- --- --- ---
+ | | | | | | | |
+ |R| |R| |R| |R|
+ | | | | | | | |
+ --- --- --- ---
+ | | | |
+ | | |\ | |
+SCL ----------x--------x--| o---x------------------------ pin 15
+ | | |/ |
+ | | |
+ | | /| |
+ | ---o |-------------x-------------- pin 2
+ | \| | |
+ | | |
+ | | |
+ | |\ | |
+SDA ---------------x---x--| o--------x------------------- pin 10
+ | |/ |
+ | |
+ | /| |
+ ---o |------------------x--------- pin 3
+ \| | |
+ | |
+ --- ---
+ | | | |
+ |R| |R|
+ | | | |
+ --- ---
+ | |
+ ### ###
+ GND GND
+
+
+If possible, you should use the same pinout configuration as existing
+adapters do, so you won't even have to change the code.
+
+
+Similar (but different) drivers
+-------------------------------
+
+This driver is NOT the same as the i2c-pport driver found in the i2c
+package. The i2c-pport driver makes use of modern parallel port features so
+that you don't need additional electronics. It has other restrictions
+however, and was not ported to Linux 2.6 (yet).
+
+This driver is also NOT the same as the i2c-pcf-epp driver found in the
+lm_sensors package. The i2c-pcf-epp driver doesn't use the parallel port as
+an I2C bus directly. Instead, it uses it to control an external I2C bus
+master. That driver was not ported to Linux 2.6 (yet) either.
+
+
+Legacy documentation for Velleman adapter
+-----------------------------------------
+
+Useful links:
+Velleman http://www.velleman.be/
+Velleman K8000 Howto http://howto.htlw16.ac.at/k8000-howto.html
+
+The project has lead to new libs for the Velleman K8000 and K8005:
+ LIBK8000 v1.99.1 and LIBK8005 v0.21
+With these libs, you can control the K8000 interface card and the K8005
+stepper motor card with the simple commands which are in the original
+Velleman software, like SetIOchannel, ReadADchannel, SendStepCCWFull and
+many more, using /dev/velleman.
+ http://home.wanadoo.nl/hihihi/libk8000.htm
+ http://home.wanadoo.nl/hihihi/libk8005.htm
+ http://struyve.mine.nu:8080/index.php?block=k8000
+ http://sourceforge.net/projects/libk8005/
+
+
+One For All JP1 parallel port adapter
+-------------------------------------
+
+The JP1 project revolves around a set of remote controls which expose
+the I2C bus their internal configuration EEPROM lives on via a 6 pin
+jumper in the battery compartment. More details can be found at:
+
+http://www.hifi-remote.com/jp1/
+
+Details of the simple parallel port hardware can be found at:
+
+http://www.hifi-remote.com/jp1/hardware.shtml
diff --git a/kernel/Documentation/i2c/busses/i2c-parport-light b/kernel/Documentation/i2c/busses/i2c-parport-light
new file mode 100644
index 000000000..7071b8ba0
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-parport-light
@@ -0,0 +1,22 @@
+Kernel driver i2c-parport-light
+
+Author: Jean Delvare <jdelvare@suse.de>
+
+This driver is a light version of i2c-parport. It doesn't depend
+on the parport driver, and uses direct I/O access instead. This might be
+preferred on embedded systems where wasting memory for the clean but heavy
+parport handling is not an option. The drawback is a reduced portability
+and the impossibility to daisy-chain other parallel port devices.
+
+Please see i2c-parport for documentation.
+
+Module parameters:
+
+* type: type of adapter (see i2c-parport or modinfo)
+
+* base: base I/O address
+ Default is 0x378 which is fairly common for parallel ports, at least on PC.
+
+* irq: optional IRQ
+ This must be passed if you want SMBus alert support, assuming your adapter
+ actually supports this.
diff --git a/kernel/Documentation/i2c/busses/i2c-pca-isa b/kernel/Documentation/i2c/busses/i2c-pca-isa
new file mode 100644
index 000000000..b044e5265
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-pca-isa
@@ -0,0 +1,23 @@
+Kernel driver i2c-pca-isa
+
+Supported adapters:
+This driver supports ISA boards using the Philips PCA 9564
+Parallel bus to I2C bus controller
+
+Author: Ian Campbell <icampbell@arcom.com>, Arcom Control Systems
+
+Module Parameters
+-----------------
+
+* base int
+ I/O base address
+* irq int
+ IRQ interrupt
+* clock int
+ Clock rate as described in table 1 of PCA9564 datasheet
+
+Description
+-----------
+
+This driver supports ISA boards using the Philips PCA 9564
+Parallel bus to I2C bus controller
diff --git a/kernel/Documentation/i2c/busses/i2c-piix4 b/kernel/Documentation/i2c/busses/i2c-piix4
new file mode 100644
index 000000000..aa959fd22
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-piix4
@@ -0,0 +1,110 @@
+Kernel driver i2c-piix4
+
+Supported adapters:
+ * Intel 82371AB PIIX4 and PIIX4E
+ * Intel 82443MX (440MX)
+ Datasheet: Publicly available at the Intel website
+ * ServerWorks OSB4, CSB5, CSB6, HT-1000 and HT-1100 southbridges
+ Datasheet: Only available via NDA from ServerWorks
+ * ATI IXP200, IXP300, IXP400, SB600, SB700 and SB800 southbridges
+ Datasheet: Not publicly available
+ SB700 register reference available at:
+ http://support.amd.com/us/Embedded_TechDocs/43009_sb7xx_rrg_pub_1.00.pdf
+ * AMD SP5100 (SB700 derivative found on some server mainboards)
+ Datasheet: Publicly available at the AMD website
+ http://support.amd.com/us/Embedded_TechDocs/44413.pdf
+ * AMD Hudson-2, ML, CZ
+ Datasheet: Not publicly available
+ * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge
+ Datasheet: Publicly available at the SMSC website http://www.smsc.com
+
+Authors:
+ Frodo Looijaard <frodol@dds.nl>
+ Philip Edelbrock <phil@netroedge.com>
+
+
+Module Parameters
+-----------------
+
+* force: int
+ Forcibly enable the PIIX4. DANGEROUS!
+* force_addr: int
+ Forcibly enable the PIIX4 at the given address. EXTREMELY DANGEROUS!
+
+
+Description
+-----------
+
+The PIIX4 (properly known as the 82371AB) is an Intel chip with a lot of
+functionality. Among other things, it implements the PCI bus. One of its
+minor functions is implementing a System Management Bus. This is a true
+SMBus - you can not access it on I2C levels. The good news is that it
+natively understands SMBus commands and you do not have to worry about
+timing problems. The bad news is that non-SMBus devices connected to it can
+confuse it mightily. Yes, this is known to happen...
+
+Do 'lspci -v' and see whether it contains an entry like this:
+
+0000:00:02.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
+ Flags: medium devsel, IRQ 9
+
+Bus and device numbers may differ, but the function number must be
+identical (like many PCI devices, the PIIX4 incorporates a number of
+different 'functions', which can be considered as separate devices). If you
+find such an entry, you have a PIIX4 SMBus controller.
+
+On some computers (most notably, some Dells), the SMBus is disabled by
+default. If you use the insmod parameter 'force=1', the kernel module will
+try to enable it. THIS IS VERY DANGEROUS! If the BIOS did not set up a
+correct address for this module, you could get in big trouble (read:
+crashes, data corruption, etc.). Try this only as a last resort (try BIOS
+updates first, for example), and backup first! An even more dangerous
+option is 'force_addr=<IOPORT>'. This will not only enable the PIIX4 like
+'force' foes, but it will also set a new base I/O port address. The SMBus
+parts of the PIIX4 needs a range of 8 of these addresses to function
+correctly. If these addresses are already reserved by some other device,
+you will get into big trouble! DON'T USE THIS IF YOU ARE NOT VERY SURE
+ABOUT WHAT YOU ARE DOING!
+
+The PIIX4E is just an new version of the PIIX4; it is supported as well.
+The PIIX/PIIX3 does not implement an SMBus or I2C bus, so you can't use
+this driver on those mainboards.
+
+The ServerWorks Southbridges, the Intel 440MX, and the Victory66 are
+identical to the PIIX4 in I2C/SMBus support.
+
+The AMD SB700, SB800, SP5100 and Hudson-2 chipsets implement two
+PIIX4-compatible SMBus controllers. If your BIOS initializes the
+secondary controller, it will be detected by this driver as
+an "Auxiliary SMBus Host Controller".
+
+If you own Force CPCI735 motherboard or other OSB4 based systems you may need
+to change the SMBus Interrupt Select register so the SMBus controller uses
+the SMI mode.
+
+1) Use lspci command and locate the PCI device with the SMBus controller:
+ 00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 4f)
+ The line may vary for different chipsets. Please consult the driver source
+ for all possible PCI ids (and lspci -n to match them). Lets assume the
+ device is located at 00:0f.0.
+2) Now you just need to change the value in 0xD2 register. Get it first with
+ command: lspci -xxx -s 00:0f.0
+ If the value is 0x3 then you need to change it to 0x1
+ setpci -s 00:0f.0 d2.b=1
+
+Please note that you don't need to do that in all cases, just when the SMBus is
+not working properly.
+
+
+Hardware-specific issues
+------------------------
+
+This driver will refuse to load on IBM systems with an Intel PIIX4 SMBus.
+Some of these machines have an RFID EEPROM (24RF08) connected to the SMBus,
+which can easily get corrupted due to a state machine bug. These are mostly
+Thinkpad laptops, but desktop systems may also be affected. We have no list
+of all affected systems, so the only safe solution was to prevent access to
+the SMBus on all IBM systems (detected using DMI data.)
+
+For additional information, read:
+http://www.lm-sensors.org/browser/lm-sensors/trunk/README
diff --git a/kernel/Documentation/i2c/busses/i2c-sis5595 b/kernel/Documentation/i2c/busses/i2c-sis5595
new file mode 100644
index 000000000..ecd21fb49
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-sis5595
@@ -0,0 +1,59 @@
+Kernel driver i2c-sis5595
+
+Authors:
+ Frodo Looijaard <frodol@dds.nl>,
+ Mark D. Studebaker <mdsxyz123@yahoo.com>,
+ Philip Edelbrock <phil@netroedge.com>
+
+Supported adapters:
+ * Silicon Integrated Systems Corp. SiS5595 Southbridge
+ Datasheet: Publicly available at the Silicon Integrated Systems Corp. site.
+
+Note: all have mfr. ID 0x1039.
+
+ SUPPORTED PCI ID
+ 5595 0008
+
+ Note: these chips contain a 0008 device which is incompatible with the
+ 5595. We recognize these by the presence of the listed
+ "blacklist" PCI ID and refuse to load.
+
+ NOT SUPPORTED PCI ID BLACKLIST PCI ID
+ 540 0008 0540
+ 550 0008 0550
+ 5513 0008 5511
+ 5581 0008 5597
+ 5582 0008 5597
+ 5597 0008 5597
+ 5598 0008 5597/5598
+ 630 0008 0630
+ 645 0008 0645
+ 646 0008 0646
+ 648 0008 0648
+ 650 0008 0650
+ 651 0008 0651
+ 730 0008 0730
+ 735 0008 0735
+ 745 0008 0745
+ 746 0008 0746
+
+Module Parameters
+-----------------
+
+* force_addr=0xaddr Set the I/O base address. Useful for boards
+ that don't set the address in the BIOS. Does not do a
+ PCI force; the device must still be present in lspci.
+ Don't use this unless the driver complains that the
+ base address is not set.
+
+Description
+-----------
+
+i2c-sis5595 is a true SMBus host driver for motherboards with the SiS5595
+southbridges.
+
+WARNING: If you are trying to access the integrated sensors on the SiS5595
+chip, you want the sis5595 driver for those, not this driver. This driver
+is a BUS driver, not a CHIP driver. A BUS driver is used by other CHIP
+drivers to access chips on the bus.
+
diff --git a/kernel/Documentation/i2c/busses/i2c-sis630 b/kernel/Documentation/i2c/busses/i2c-sis630
new file mode 100644
index 000000000..ee7943631
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-sis630
@@ -0,0 +1,58 @@
+Kernel driver i2c-sis630
+
+Supported adapters:
+ * Silicon Integrated Systems Corp (SiS)
+ 630 chipset (Datasheet: available at http://www.sfr-fresh.com/linux)
+ 730 chipset
+ 964 chipset
+ * Possible other SiS chipsets ?
+
+Author: Alexander Malysh <amalysh@web.de>
+ Amaury Decrême <amaury.decreme@gmail.com> - SiS964 support
+
+Module Parameters
+-----------------
+
+* force = [1|0] Forcibly enable the SIS630. DANGEROUS!
+ This can be interesting for chipsets not named
+ above to check if it works for you chipset, but DANGEROUS!
+
+* high_clock = [1|0] Forcibly set Host Master Clock to 56KHz (default,
+ what your BIOS use). DANGEROUS! This should be a bit
+ faster, but freeze some systems (i.e. my Laptop).
+ SIS630/730 chip only.
+
+
+Description
+-----------
+
+This SMBus only driver is known to work on motherboards with the above
+named chipsets.
+
+If you see something like this:
+
+00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 31)
+00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
+
+or like this:
+
+00:00.0 Host bridge: Silicon Integrated Systems [SiS] 730 Host (rev 02)
+00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
+
+or like this:
+
+00:00.0 Host bridge: Silicon Integrated Systems [SiS] 760/M760 Host (rev 02)
+00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS964 [MuTIOL Media IO]
+ LPC Controller (rev 36)
+
+in your 'lspci' output , then this driver is for your chipset.
+
+Thank You
+---------
+Philip Edelbrock <phil@netroedge.com>
+- testing SiS730 support
+Mark M. Hoffman <mhoffman@lightlink.com>
+- bug fixes
+
+To anyone else which I forgot here ;), thanks!
+
diff --git a/kernel/Documentation/i2c/busses/i2c-sis96x b/kernel/Documentation/i2c/busses/i2c-sis96x
new file mode 100644
index 000000000..0b979f325
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-sis96x
@@ -0,0 +1,73 @@
+Kernel driver i2c-sis96x
+
+Replaces 2.4.x i2c-sis645
+
+Supported adapters:
+ * Silicon Integrated Systems Corp (SiS)
+ Any combination of these host bridges:
+ 645, 645DX (aka 646), 648, 650, 651, 655, 735, 745, 746
+ and these south bridges:
+ 961, 962, 963(L)
+
+Author: Mark M. Hoffman <mhoffman@lightlink.com>
+
+Description
+-----------
+
+This SMBus only driver is known to work on motherboards with the above
+named chipset combinations. The driver was developed without benefit of a
+proper datasheet from SiS. The SMBus registers are assumed compatible with
+those of the SiS630, although they are located in a completely different
+place. Thanks to Alexander Malysh <amalysh@web.de> for providing the
+SiS630 datasheet (and driver).
+
+The command "lspci" as root should produce something like these lines:
+
+00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0645
+00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
+00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016
+
+or perhaps this...
+
+00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0645
+00:02.0 ISA bridge: Silicon Integrated Systems [SiS]: Unknown device 0961
+00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016
+
+(kernel versions later than 2.4.18 may fill in the "Unknown"s)
+
+If you can't see it please look on quirk_sis_96x_smbus
+(drivers/pci/quirks.c) (also if southbridge detection fails)
+
+I suspect that this driver could be made to work for the following SiS
+chipsets as well: 635, and 635T. If anyone owns a board with those chips
+AND is willing to risk crashing & burning an otherwise well-behaved kernel
+in the name of progress... please contact me at <mhoffman@lightlink.com> or
+via the linux-i2c mailing list: <linux-i2c@vger.kernel.org>. Please send bug
+reports and/or success stories as well.
+
+
+TO DOs
+------
+
+* The driver does not support SMBus block reads/writes; I may add them if a
+scenario is found where they're needed.
+
+
+Thank You
+---------
+
+Mark D. Studebaker <mdsxyz123@yahoo.com>
+ - design hints and bug fixes
+Alexander Maylsh <amalysh@web.de>
+ - ditto, plus an important datasheet... almost the one I really wanted
+Hans-Günter Lütke Uphues <hg_lu@t-online.de>
+ - patch for SiS735
+Robert Zwerus <arzie@dds.nl>
+ - testing for SiS645DX
+Kianusch Sayah Karadji <kianusch@sk-tech.net>
+ - patch for SiS645DX/962
+Ken Healy
+ - patch for SiS655
+
+To anyone else who has written w/ feedback, thanks!
+
diff --git a/kernel/Documentation/i2c/busses/i2c-taos-evm b/kernel/Documentation/i2c/busses/i2c-taos-evm
new file mode 100644
index 000000000..60299555d
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-taos-evm
@@ -0,0 +1,46 @@
+Kernel driver i2c-taos-evm
+
+Author: Jean Delvare <jdelvare@suse.de>
+
+This is a driver for the evaluation modules for TAOS I2C/SMBus chips.
+The modules include an SMBus master with limited capabilities, which can
+be controlled over the serial port. Virtually all evaluation modules
+are supported, but a few lines of code need to be added for each new
+module to instantiate the right I2C chip on the bus. Obviously, a driver
+for the chip in question is also needed.
+
+Currently supported devices are:
+
+* TAOS TSL2550 EVM
+
+For additional information on TAOS products, please see
+ http://www.taosinc.com/
+
+
+Using this driver
+-----------------
+
+In order to use this driver, you'll need the serport driver, and the
+inputattach tool, which is part of the input-utils package. The following
+commands will tell the kernel that you have a TAOS EVM on the first
+serial port:
+
+# modprobe serport
+# inputattach --taos-evm /dev/ttyS0
+
+
+Technical details
+-----------------
+
+Only 4 SMBus transaction types are supported by the TAOS evaluation
+modules:
+* Receive Byte
+* Send Byte
+* Read Byte
+* Write Byte
+
+The communication protocol is text-based and pretty simple. It is
+described in a PDF document on the CD which comes with the evaluation
+module. The communication is rather slow, because the serial port has
+to operate at 1200 bps. However, I don't think this is a big concern in
+practice, as these modules are meant for evaluation and testing only.
diff --git a/kernel/Documentation/i2c/busses/i2c-via b/kernel/Documentation/i2c/busses/i2c-via
new file mode 100644
index 000000000..343870661
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-via
@@ -0,0 +1,34 @@
+Kernel driver i2c-via
+
+Supported adapters:
+ * VIA Technologies, InC. VT82C586B
+ Datasheet: Publicly available at the VIA website
+
+Author: Kyösti Mälkki <kmalkki@cc.hut.fi>
+
+Description
+-----------
+
+i2c-via is an i2c bus driver for motherboards with VIA chipset.
+
+The following VIA pci chipsets are supported:
+ - MVP3, VP3, VP2/97, VPX/97
+ - others with South bridge VT82C586B
+
+Your lspci listing must show this :
+
+ Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
+
+ Problems?
+
+ Q: You have VT82C586B on the motherboard, but not in the listing.
+
+ A: Go to your BIOS setup, section PCI devices or similar.
+ Turn USB support on, and try again.
+
+ Q: No error messages, but still i2c doesn't seem to work.
+
+ A: This can happen. This driver uses the pins VIA recommends in their
+ datasheets, but there are several ways the motherboard manufacturer
+ can actually wire the lines.
+
diff --git a/kernel/Documentation/i2c/busses/i2c-viapro b/kernel/Documentation/i2c/busses/i2c-viapro
new file mode 100644
index 000000000..ab64ce21c
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/i2c-viapro
@@ -0,0 +1,73 @@
+Kernel driver i2c-viapro
+
+Supported adapters:
+ * VIA Technologies, Inc. VT82C596A/B
+ Datasheet: Sometimes available at the VIA website
+
+ * VIA Technologies, Inc. VT82C686A/B
+ Datasheet: Sometimes available at the VIA website
+
+ * VIA Technologies, Inc. VT8231, VT8233, VT8233A
+ Datasheet: available on request from VIA
+
+ * VIA Technologies, Inc. VT8235, VT8237R, VT8237A, VT8237S, VT8251
+ Datasheet: available on request and under NDA from VIA
+
+ * VIA Technologies, Inc. CX700
+ Datasheet: available on request and under NDA from VIA
+
+ * VIA Technologies, Inc. VX800/VX820
+ Datasheet: available on http://linux.via.com.tw
+
+ * VIA Technologies, Inc. VX855/VX875
+ Datasheet: available on http://linux.via.com.tw
+
+ * VIA Technologies, Inc. VX900
+ Datasheet: available on http://linux.via.com.tw
+
+Authors:
+ Kyösti Mälkki <kmalkki@cc.hut.fi>,
+ Mark D. Studebaker <mdsxyz123@yahoo.com>,
+ Jean Delvare <jdelvare@suse.de>
+
+Module Parameters
+-----------------
+
+* force: int
+ Forcibly enable the SMBus controller. DANGEROUS!
+* force_addr: int
+ Forcibly enable the SMBus at the given address. EXTREMELY DANGEROUS!
+
+Description
+-----------
+
+i2c-viapro is a true SMBus host driver for motherboards with one of the
+supported VIA south bridges.
+
+Your lspci -n listing must show one of these :
+
+ device 1106:3050 (VT82C596A function 3)
+ device 1106:3051 (VT82C596B function 3)
+ device 1106:3057 (VT82C686 function 4)
+ device 1106:3074 (VT8233)
+ device 1106:3147 (VT8233A)
+ device 1106:8235 (VT8231 function 4)
+ device 1106:3177 (VT8235)
+ device 1106:3227 (VT8237R)
+ device 1106:3337 (VT8237A)
+ device 1106:3372 (VT8237S)
+ device 1106:3287 (VT8251)
+ device 1106:8324 (CX700)
+ device 1106:8353 (VX800/VX820)
+ device 1106:8409 (VX855/VX875)
+ device 1106:8410 (VX900)
+
+If none of these show up, you should look in the BIOS for settings like
+enable ACPI / SMBus or even USB.
+
+Except for the oldest chips (VT82C596A/B, VT82C686A and most probably
+VT8231), this driver supports I2C block transactions. Such transactions
+are mainly useful to read from and write to EEPROMs.
+
+The CX700/VX800/VX820 additionally appears to support SMBus PEC, although
+this driver doesn't implement it yet.
diff --git a/kernel/Documentation/i2c/busses/scx200_acb b/kernel/Documentation/i2c/busses/scx200_acb
new file mode 100644
index 000000000..ce83c871f
--- /dev/null
+++ b/kernel/Documentation/i2c/busses/scx200_acb
@@ -0,0 +1,32 @@
+Kernel driver scx200_acb
+
+Author: Christer Weinigel <wingel@nano-system.com>
+
+The driver supersedes the older, never merged driver named i2c-nscacb.
+
+Module Parameters
+-----------------
+
+* base: up to 4 ints
+ Base addresses for the ACCESS.bus controllers on SCx200 and SC1100 devices
+
+ By default the driver uses two base addresses 0x820 and 0x840.
+ If you want only one base address, specify the second as 0 so as to
+ override this default.
+
+Description
+-----------
+
+Enable the use of the ACCESS.bus controller on the Geode SCx200 and
+SC1100 processors and the CS5535 and CS5536 Geode companion devices.
+
+Device-specific notes
+---------------------
+
+The SC1100 WRAP boards are known to use base addresses 0x810 and 0x820.
+If the scx200_acb driver is built into the kernel, add the following
+parameter to your boot command line:
+ scx200_acb.base=0x810,0x820
+If the scx200_acb driver is built as a module, add the following line to
+a configuration file in /etc/modprobe.d/ instead:
+ options scx200_acb base=0x810,0x820