diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt')
| -rw-r--r-- | kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 58 |
1 files changed, 57 insertions, 1 deletions
diff --git a/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 27f8b1e5e..781296bfb 100644 --- a/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -1,15 +1,64 @@ * USB2 ChipIdea USB controller for ci13xxx Required properties: -- compatible: should be "chipidea,usb2" +- compatible: should be one of: + "fsl,imx27-usb" + "lsi,zevio-usb" + "qcom,ci-hdrc" + "chipidea,usb2" + "xlnx,zynq-usb-2.20a" - reg: base address and length of the registers - interrupts: interrupt for the USB controller +Recommended properies: +- phy_type: the type of the phy connected to the core. Should be one + of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this + property the PORTSC register won't be touched. +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +Deprecated properties: +- usb-phy: phandle for the PHY device. Use "phys" instead. +- fsl,usbphy: phandle of usb phy that connects to the port. Use "phys" instead. + Optional properties: - clocks: reference to the USB clock - phys: reference to the USB PHY - phy-names: should be "usb-phy" - vbus-supply: reference to the VBUS regulator +- maximum-speed: limit the maximum connection speed to "full-speed". +- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts +- itc-setting: interrupt threshold control register control, the setting + should be aligned with ITC bits at register USBCMD. +- ahb-burst-config: it is vendor dependent, the required value should be + aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This + property is used to change AHB burst configuration, check the chipidea + spec for meaning of each value. If this property is not existed, it + will use the reset value. +- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from system memory to the USB + bus, the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from the USB bus to system memory, + the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- extcon: phandles to external connector devices. First phandle should point to + external connector, which provide "USB" cable events, the second should point + to external connector device, which provide "USB-HOST" cable events. If one + of the external connector devices is not required, empty <0> phandle should + be specified. +- phy-clkgate-delay-us: the delay time (us) between putting the PHY into + low power mode and gating the PHY clock. + +i.mx specific properties +- fsl,usbmisc: phandler of non-core register device, with one + argument that indicate usb controller index +- disable-over-current: disable over current detect +- external-vbus-divider: enables off-chip resistor divider for Vbus Example: @@ -21,4 +70,11 @@ Example: phys = <&usb_phy0>; phy-names = "usb-phy"; vbus-supply = <®_usb0_vbus>; + gadget-itc-setting = <0x4>; /* 4 micro-frames */ + /* Incremental burst of unspecified length */ + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; /* 64 bytes */ + rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; + phy-clkgate-delay-us = <400>; }; |