diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/regulator')
38 files changed, 2850 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/regulator/88pm800.txt b/kernel/Documentation/devicetree/bindings/regulator/88pm800.txt new file mode 100644 index 000000000..e8a54c2a5 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/88pm800.txt @@ -0,0 +1,38 @@ +Marvell 88PM800 regulator + +Required properties: +- compatible: "marvell,88pm800" +- reg: I2C slave address +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + +The valid names for regulators are: + + buck1, buck2, buck3, buck4, buck5, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, + ldo8, ldo9, ldo10, ldo11, ldo12, ldo13, ldo14, ldo15, ldo16, ldo17, ldo18, ldo19 + +Example: + + pmic: 88pm800@31 { + compatible = "marvell,88pm800"; + reg = <0x31>; + + regulators { + buck1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3950000>; + regulator-boot-on; + regulator-always-on; + }; + ldo1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <15000000>; + regulator-boot-on; + regulator-always-on; + }; +... + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/88pm860x.txt b/kernel/Documentation/devicetree/bindings/regulator/88pm860x.txt new file mode 100644 index 000000000..1267b3e1a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/88pm860x.txt @@ -0,0 +1,30 @@ +Marvell 88PM860x regulator + +Required properties: +- compatible: "marvell,88pm860x" +- reg: I2C slave address +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the regulator-compatible + property, with valid values listed below. + +Example: + + pmic: 88pm860x@34 { + compatible = "marvell,88pm860x"; + reg = <0x34>; + + regulators { + BUCK1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + BUCK3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/act8865-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/act8865-regulator.txt new file mode 100644 index 000000000..e91485d11 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/act8865-regulator.txt @@ -0,0 +1,92 @@ +ACT88xx regulators +------------------- + +Required properties: +- compatible: "active-semi,act8846" or "active-semi,act8865" or "active-semi,act8600" +- reg: I2C slave address + +Optional properties: +- system-power-controller: Telling whether or not this pmic is controlling + the system power. See Documentation/devicetree/bindings/power/power-controller.txt . + +Optional input supply properties: +- for act8600: + - vp1-supply: The input supply for DCDC_REG1 + - vp2-supply: The input supply for DCDC_REG2 + - vp3-supply: The input supply for DCDC_REG3 + - inl-supply: The input supply for LDO_REG5, LDO_REG6, LDO_REG7 and LDO_REG8 + SUDCDC_REG4, LDO_REG9 and LDO_REG10 do not have separate supplies. +- for act8846: + - vp1-supply: The input supply for REG1 + - vp2-supply: The input supply for REG2 + - vp3-supply: The input supply for REG3 + - vp4-supply: The input supply for REG4 + - inl1-supply: The input supply for REG5, REG6 and REG7 + - inl2-supply: The input supply for REG8 and LDO_REG9 + - inl3-supply: The input supply for REG10, REG11 and REG12 +- for act8865: + - vp1-supply: The input supply for DCDC_REG1 + - vp2-supply: The input supply for DCDC_REG2 + - vp3-supply: The input supply for DCDC_REG3 + - inl45-supply: The input supply for LDO_REG1 and LDO_REG2 + - inl67-supply: The input supply for LDO_REG3 and LDO_REG4 + +Any standard regulator properties can be used to configure the single regulator. + +The valid names for regulators are: + - for act8846: + REG1, REG2, REG3, REG4, REG5, REG6, REG7, REG8, REG9, REG10, REG11, REG12 + - for act8865: + DCDC_REG1, DCDC_REG2, DCDC_REG3, LDO_REG1, LDO_REG2, LDO_REG3, LDO_REG4. + - for act8600: + DCDC_REG1, DCDC_REG2, DCDC_REG3, SUDCDC_REG4, LDO_REG5, LDO_REG6, LDO_REG7, + LDO_REG8, LDO_REG9, LDO_REG10, + +Example: +-------- + + i2c1: i2c@f0018000 { + pmic: act8865@5b { + compatible = "active-semi,act8865"; + reg = <0x5b>; + status = "disabled"; + + regulators { + vcc_1v8_reg: DCDC_REG1 { + regulator-name = "VCC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vcc_1v2_reg: DCDC_REG2 { + regulator-name = "VCC_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-suspend-mem-microvolt = <1150000>; + regulator-suspend-standby-microvolt = <1150000>; + regulator-always-on; + }; + + vcc_3v3_reg: DCDC_REG3 { + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vddana_reg: LDO_REG1 { + regulator-name = "VDDANA"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vddfuse_reg: LDO_REG2 { + regulator-name = "FUSE_2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/anatop-regulator.txt new file mode 100644 index 000000000..758eae240 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -0,0 +1,37 @@ +Anatop Voltage regulators + +Required properties: +- compatible: Must be "fsl,anatop-regulator" +- anatop-reg-offset: Anatop MFD register offset +- anatop-vol-bit-shift: Bit shift for the register +- anatop-vol-bit-width: Number of bits used in the register +- anatop-min-bit-val: Minimum value of this register +- anatop-min-voltage: Minimum voltage of this regulator +- anatop-max-voltage: Maximum voltage of this regulator + +Optional properties: +- anatop-delay-reg-offset: Anatop MFD step time register offset +- anatop-delay-bit-shift: Bit shift for the step time register +- anatop-delay-bit-width: Number of bits used in the step time register + +Any property defined as part of the core regulator +binding, defined in regulator.txt, can also be used. + +Example: + + regulator-vddpu { + compatible = "fsl,anatop-regulator"; + regulator-name = "vddpu"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + anatop-reg-offset = <0x140>; + anatop-vol-bit-shift = <9>; + anatop-vol-bit-width = <5>; + anatop-delay-reg-offset = <0x170>; + anatop-delay-bit-shift = <24>; + anatop-delay-bit-width = <2>; + anatop-min-bit-val = <1>; + anatop-min-voltage = <725000>; + anatop-max-voltage = <1300000>; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/as3722-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/as3722-regulator.txt new file mode 100644 index 000000000..caad0c8a2 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/as3722-regulator.txt @@ -0,0 +1,91 @@ +Regulator of AMS AS3722 PMIC. +Name of the regulator subnode must be "regulators". + +Optional properties: +-------------------- +The input supply of regulators are the optional properties on the +regulator node. The AS3722 is having 7 DCDC step-down regulators as +sd[0-6], 10 LDOs as ldo[0-7], ldo[9-11]. The input supply of these +regulators are provided through following properties: +vsup-sd2-supply: Input supply for SD2. +vsup-sd3-supply: Input supply for SD3. +vsup-sd4-supply: Input supply for SD4. +vsup-sd5-supply: Input supply for SD5. +vin-ldo0-supply: Input supply for LDO0. +vin-ldo1-6-supply: Input supply for LDO1 and LDO6. +vin-ldo2-5-7-supply: Input supply for LDO2, LDO5 and LDO7. +vin-ldo3-4-supply: Input supply for LDO3 and LDO4. +vin-ldo9-10-supply: Input supply for LDO9 and LDO10. +vin-ldo11-supply: Input supply for LDO11. + +Optional nodes: +-------------- +- regulators : Must contain a sub-node per regulator from the list below. + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a + description of standard properties for these sub-nodes. + Additional custom properties are listed below. + sd[0-6], ldo[0-7], ldo[9-11]. + + Optional sub-node properties: + ---------------------------- + ams,ext-control: External control of the rail. The option of + this properties will tell which external input is + controlling this rail. Valid values are 0, 1, 2 ad 3. + 0: There is no external control of this rail. + 1: Rail is controlled by ENABLE1 input pin. + 2: Rail is controlled by ENABLE2 input pin. + 3: Rail is controlled by ENABLE3 input pin. + ams,enable-tracking: Enable tracking with SD1, only supported + by LDO3. + +Example: +------- + ams3722: ams3722 { + compatible = "ams,as3722"; + reg = <0x40>; + ... + + regulators { + vsup-sd2-supply = <...>; + ... + + sd0 { + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + ams,ext-control = <2>; + }; + + sd1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + ams,ext-control = <1>; + }; + + sd2 { + regulator-name = "vddio_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + sd4 { + regulator-name = "avdd-hdmi-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + }; + + sd5 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + .... + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/da9210.txt b/kernel/Documentation/devicetree/bindings/regulator/da9210.txt new file mode 100644 index 000000000..3297c53cb --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/da9210.txt @@ -0,0 +1,21 @@ +* Dialog Semiconductor DA9210 Voltage Regulator + +Required properties: + +- compatible: must be "dlg,da9210" +- reg: the i2c slave address of the regulator. It should be 0x68. + +Any standard regulator properties can be used to configure the single da9210 +DCDC. + +Example: + + da9210@68 { + compatible = "dlg,da9210"; + reg = <0x68>; + + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/da9211.txt b/kernel/Documentation/devicetree/bindings/regulator/da9211.txt new file mode 100644 index 000000000..eb618907c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/da9211.txt @@ -0,0 +1,68 @@ +* Dialog Semiconductor DA9211/DA9213 Voltage Regulator + +Required properties: +- compatible: "dlg,da9211" or "dlg,da9213". +- reg: I2C slave address, usually 0x68. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCKA and BUCKB. + +Optional properties: +- enable-gpios: platform gpio for control of BUCKA/BUCKB. +- Any optional property defined in regulator.txt + +Example 1) DA9211 + + pmic: da9211@68 { + compatible = "dlg,da9211"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 27 0>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 17 0>; + }; + }; + }; + +Example 2) DA9213 + pmic: da9213@68 { + compatible = "dlg,da9213"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 27 0>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 17 0>; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/fan53555.txt b/kernel/Documentation/devicetree/bindings/regulator/fan53555.txt new file mode 100644 index 000000000..54a3f2c80 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/fan53555.txt @@ -0,0 +1,23 @@ +Binding for Fairchild FAN53555 regulators + +Required properties: + - compatible: one of "fcs,fan53555", "silergy,syr827", "silergy,syr828" + - reg: I2C address + +Optional properties: + - fcs,suspend-voltage-selector: declare which of the two available + voltage selector registers should be used for the suspend + voltage. The other one is used for the runtime voltage setting + Possible values are either <0> or <1> + - vin-supply: regulator supplying the vin pin + +Example: + + regulator@40 { + compatible = "fcs,fan53555"; + regulator-name = "fan53555"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&parent_reg>; + fcs,suspend-voltage-selector = <1>; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/fixed-regulator.txt new file mode 100644 index 000000000..4fae41d54 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/fixed-regulator.txt @@ -0,0 +1,34 @@ +Fixed Voltage regulators + +Required properties: +- compatible: Must be "regulator-fixed"; + +Optional properties: +- gpio: gpio to use for enable control +- startup-delay-us: startup time in microseconds +- enable-active-high: Polarity of GPIO is Active high +If this property is missing, the default assumed is Active low. +- gpio-open-drain: GPIO is open drain type. + If this property is missing then default assumption is false. +-vin-supply: Input supply name. + +Any property defined as part of the core regulator +binding, defined in regulator.txt, can also be used. +However a fixed voltage regulator is expected to have the +regulator-min-microvolt and regulator-max-microvolt +to be the same. + +Example: + + abc: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 16 0>; + startup-delay-us = <70000>; + enable-active-high; + regulator-boot-on; + gpio-open-drain; + vin-supply = <&parent_reg>; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/gpio-regulator.txt new file mode 100644 index 000000000..e5cac1e0c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/gpio-regulator.txt @@ -0,0 +1,41 @@ +GPIO controlled regulators + +Required properties: +- compatible : Must be "regulator-gpio". +- states : Selection of available voltages and GPIO configs. + if there are no states, then use a fixed regulator + +Optional properties: +- enable-gpio : GPIO to use to enable/disable the regulator. +- gpios : GPIO group used to control voltage. +- gpios-states : gpios pin's initial states array. 0: LOW, 1: HIGH. + defualt is LOW if nothing is specified. +- startup-delay-us : Startup time in microseconds. +- enable-active-high : Polarity of GPIO is active high (default is low). +- regulator-type : Specifies what is being regulated, must be either + "voltage" or "current", defaults to current. + +Any property defined as part of the core regulator binding defined in +regulator.txt can also be used. + +Example: + + mmciv: gpio-regulator { + compatible = "regulator-gpio"; + + regulator-name = "mmci-gpio-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2600000>; + regulator-boot-on; + + enable-gpio = <&gpio0 23 0x4>; + gpios = <&gpio0 24 0x4 + &gpio0 25 0x4>; + states = <1800000 0x3 + 2200000 0x2 + 2600000 0x1 + 2900000 0x0>; + + startup-delay-us = <100000>; + enable-active-high; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/isl9305.txt b/kernel/Documentation/devicetree/bindings/regulator/isl9305.txt new file mode 100644 index 000000000..d6e7c9ec9 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/isl9305.txt @@ -0,0 +1,36 @@ +Intersil ISL9305/ISL9305H voltage regulator + +Required properties: + +- compatible: "isil,isl9305" or "isil,isl9305h" +- reg: I2C slave address, usually 0x68. +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values being "dcd1", "dcd2", "ldo1" and "ldo2". The content of each sub-node + is defined by the standard binding for regulators; see regulator.txt. +- VINDCD1-supply: A phandle to a regulator node supplying VINDCD1. + VINDCD2-supply: A phandle to a regulator node supplying VINDCD2. + VINLDO1-supply: A phandle to a regulator node supplying VINLDO1. + VINLDO2-supply: A phandle to a regulator node supplying VINLDO2. + +Optional properties: +- Per-regulator optional properties are defined in regulator.txt + +Example + + pmic: isl9305@68 { + compatible = "isil,isl9305"; + reg = <0x68>; + + VINDCD1-supply = <&system_power>; + VINDCD2-supply = <&system_power>; + VINLDO1-supply = <&system_power>; + VINLDO2-supply = <&system_power>; + + regulators { + dcd1 { + regulator-name = "VDD_DSP"; + regulator-always-on; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/lp872x.txt b/kernel/Documentation/devicetree/bindings/regulator/lp872x.txt new file mode 100644 index 000000000..78183182d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -0,0 +1,160 @@ +Binding for TI/National Semiconductor LP872x Driver + +Required properties: + - compatible: "ti,lp8720" or "ti,lp8725" + - reg: I2C slave address. 0x7d = LP8720, 0x7a = LP8725 + +Optional properties: + - ti,general-config: the value of LP872X_GENERAL_CFG register (u8) + (LP8720) + bit[2]: BUCK output voltage control by external DVS pin or register + 1 = external pin, 0 = bit7 of register 08h + bit[1]: sleep control by external DVS pin or register + 1 = external pin, 0 = bit6 of register 08h + bit[0]: time step unit(usec). 1 = 25, 0 = 50 + + (LP8725) + bit[7:6]: time step unit(usec). 00 = 32, 01 = 64, 10 = 128, 11 = 256 + bit[4]: BUCK2 enable control. 1 = enable, 0 = disable + bit[3]: BUCK2 output voltage register address. 1 = 0Ah, 0 = 0Bh + bit[2]: BUCK1 output voltage control by external DVS pin or register + 1 = register 08h, 0 = DVS + bit[1]: LDO sleep control. 1 = sleep mode, 0 = normal + bit[0]: BUCK1 enable control, 1 = enable, 0 = disable + + For more details, please see the datasheet. + + - ti,update-config: define it when LP872X_GENERAL_CFG register should be set + - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. + - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. + - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + + Sub nodes for regulator_init_data + LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) + LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2) + For more details, please see the following binding document. + (Documentation/devicetree/bindings/regulator/regulator.txt) + +Datasheet + - LP8720: http://www.ti.com/lit/ds/symlink/lp8720.pdf + - LP8725: http://www.ti.com/lit/ds/symlink/lp8725.pdf + +Example 1) LP8720 + +lp8720@7d { + compatible = "ti,lp8720"; + reg = <0x7d>; + + /* external DVS pin used, timestep is 25usec */ + ti,general-config = /bits/ 8 <0x03>; + ti,update-config; + + /* + * The dvs-gpio depends on the processor environment. + * For example, following GPIO specifier means GPIO134 in OMAP4. + */ + ti,dvs-gpio = <&gpio5 6 0>; + ti,dvs-vsel = /bits/ 8 <1>; /* SEL_V2 */ + ti,dvs-state = /bits/ 8 <1>; /* DVS_HIGH */ + + vaf: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vmmc: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam_io: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vcam_core: ldo4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2850000>; + regulator-boot-on; + }; + + vcam: ldo5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcc: buck { + regulator-name = "VBUCK"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2300000>; + }; +}; + +Example 2) LP8725 + +lp8725@7a { + compatible = "ti,lp8725"; + reg = <0x7a>; + + /* Enable BUCK1,2, no DVS, normal LDO mode, timestep is 256usec */ + ti,general-config = /bits/ 8 <0xdd>; + ti,update-config; + + vcam_io: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam_core: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcmmb_io: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vcmmb_core: ldo5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vaux1: lilo1 { + regulator-name = "VAUX1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + vaux2: lilo2 { + regulator-name = "VAUX2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + vcc1: buck1 { + regulator-name = "VBUCK1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-min-microamp = <460000>; + regulator-max-microamp = <1370000>; + regulator-boot-on; + }; + + vcc2: buck2 { + regulator-name = "VBUCK2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-min-microamp = <460000>; + regulator-max-microamp = <1370000>; + regulator-boot-on; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/regulator/ltc3589.txt b/kernel/Documentation/devicetree/bindings/regulator/ltc3589.txt new file mode 100644 index 000000000..801053036 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/ltc3589.txt @@ -0,0 +1,99 @@ +Linear Technology LTC3589, LTC3589-1, and LTC3589-2 8-output regulators + +Required properties: +- compatible: "lltc,ltc3589", "lltc,ltc3589-1" or "lltc,ltc3589-2" +- reg: I2C slave address + +Required child node: +- regulators: Contains eight regulator child nodes sw1, sw2, sw3, bb-out, + ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as + documented in Documentation/devicetree/bindings/regulator/regulator.txt. + +Each regulator is defined using the standard binding for regulators. The +nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify +the resistor values of their external feedback voltage dividers: + +Required properties (not on ldo3, ldo4): +- lltc,fb-voltage-divider: An array of two integers containing the resistor + values R1 and R2 of the feedback voltage divider in ohms. + +Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from +0.3625 V to 0.75 V in 12.5 mV steps. The output voltage thus ranges between +0.3625 * (1 + R1/R2) V and 0.75 * (1 + R1/R2) V. Regulators bb-out and ldo1 +have a fixed 0.8 V reference and thus output 0.8 * (1 + R1/R2) V. The ldo3 +regulator is fixed to 1.8 V on LTC3589 and to 2.8 V on LTC3589-1,2. The ldo4 +regulator can output between 1.8 V and 3.3 V on LTC3589 and between 1.2 V +and 3.2 V on LTC3589-1,2 in four steps. The ldo1 standby regulator can not +be disabled and thus should have the regulator-always-on property set. + +Example: + + ltc3589: pmic@34 { + compatible = "lltc,ltc3589-1"; + reg = <0x34>; + + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <591930>; + regulator-max-microvolt = <1224671>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456803>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <1341250>; + regulator-max-microvolt = <2775000>; + lltc,fb-voltage-divider = <270000 100000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + bb_out_reg: bb-out { + regulator-min-microvolt = <3387341>; + regulator-max-microvolt = <3387341>; + lltc,fb-voltage-divider = <511000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + regulator-min-microvolt = <1306329>; + regulator-max-microvolt = <1306329>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456806>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3200000>; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/max1586-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/max1586-regulator.txt new file mode 100644 index 000000000..c050c1744 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/max1586-regulator.txt @@ -0,0 +1,28 @@ +Maxim MAX1586 voltage regulator + +Required properties: +- compatible: must be "maxim,max1586" +- reg: I2C slave address, usually 0x14 +- v3-gain: integer specifying the V3 gain as per datasheet + (1 + R24/R25 + R24/185.5kOhm) +- any required generic properties defined in regulator.txt + +Example: + + i2c_master { + max1586@14 { + compatible = "maxim,max1586"; + reg = <0x14>; + v3-gain = <1000000>; + + regulators { + vcc_core: v3 { + regulator-name = "vcc_core"; + regulator-compatible = "Output_V3"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1705000>; + regulator-always-on; + }; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/max77802.txt b/kernel/Documentation/devicetree/bindings/regulator/max77802.txt new file mode 100644 index 000000000..79e547644 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/max77802.txt @@ -0,0 +1,88 @@ +Binding for Maxim MAX77802 regulators + +This is a part of device tree bindings of MAX77802 multi-function device. +More information can be found in bindings/mfd/max77802.txt file. + +The MAX77802 PMIC has 10 high-efficiency Buck and 32 Low-dropout (LDO) +regulators that can be controlled over I2C. + +Following properties should be present in main device node of the MFD chip. + +Optional node: +- regulators : The regulators of max77802 have to be instantiated + under subnode named "regulators" using the following format. + + regulator-name { + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + +The regulator node name should be initialized with a string to get matched +with their hardware counterparts as follow. The valid names are: + + -LDOn : for LDOs, where n can lie in ranges 1-15, 17-21, 23-30 + and 32-35. + example: LDO1, LDO2, LDO35. + -BUCKn : for BUCKs, where n can lie in range 1 to 10. + example: BUCK1, BUCK5, BUCK10. + +The max77802 regulator supports two different operating modes: Normal and Low +Power Mode. Some regulators support the modes to be changed at startup or by +the consumers during normal operation while others only support to change the +mode during system suspend. The standard regulator suspend states binding can +be used to configure the regulator operating mode. + +The regulators that support the standard "regulator-initial-mode" property, +changing their mode during normal operation are: LDOs 1, 3, 20 and 21. + +The possible values for "regulator-initial-mode" and "regulator-mode" are: + 1: Normal regulator voltage output mode. + 3: Low Power which reduces the quiescent current down to only 1uA + +The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +header and can be included by device tree source files. + +The standard "regulator-mode" property can only be used for regulators that +support changing their mode to Low Power Mode during suspend. These regulators +are: BUCKs 2-4 and LDOs 1-35. Also, it only takes effect if the regulator has +been enabled for the given suspend state using "regulator-on-in-suspend" and +has not been disabled for that state using "regulator-off-in-suspend". + +Example: + + max77802@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #address-cells = <1>; + #size-cells = <0>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "vdd_1v0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-initial-mode = <MAX77802_OPMODE_LP>; + }; + + ldo11_reg: LDO11 { + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-mode = <MAX77802_OPMODE_LP>; + }; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/max8660.txt b/kernel/Documentation/devicetree/bindings/regulator/max8660.txt new file mode 100644 index 000000000..8ba994d8a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/max8660.txt @@ -0,0 +1,47 @@ +Maxim MAX8660 voltage regulator + +Required properties: +- compatible: must be one of "maxim,max8660", "maxim,max8661" +- reg: I2C slave address, usually 0x34 +- any required generic properties defined in regulator.txt + +Example: + + i2c_master { + max8660@34 { + compatible = "maxim,max8660"; + reg = <0x34>; + + regulators { + regulator@0 { + regulator-compatible= "V3(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@1 { + regulator-compatible= "V4(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@2 { + regulator-compatible= "V5(LDO)"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + }; + + regulator@3 { + regulator-compatible= "V6(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + regulator@4 { + regulator-compatible= "V7(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/max8907.txt b/kernel/Documentation/devicetree/bindings/regulator/max8907.txt new file mode 100644 index 000000000..371eccd1c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/max8907.txt @@ -0,0 +1,69 @@ +MAX8907 regulator + +Required properties: +- compatible: "maxim,max8907" +- reg: I2C slave address +- interrupts: The interrupt output of the controller +- mbatt-supply: The input supply for MBATT, BBAT, SDBY, VRTC. +- in-v1-supply: The input supply for SD1. +- in-v2-supply: The input supply for SD2. +- in-v3-supply: The input supply for SD3. +- in1-supply: The input supply for LDO1. +... +- in20-supply: The input supply for LDO20. +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + +Optional properties: +- maxim,system-power-controller: Boolean property indicating that the PMIC + controls the overall system power. + +The valid names for regulators are: + + sd1, sd2, sd3, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8, ldo9, ldo10, + ldo11, ldo12, ldo13, ldo14, ldo15, ldo16, ldo17, ldo18, ldo19, ldo20, out5v, + out33v, bbat, sdby, vrtc. + +Example: + + max8907@3c { + compatible = "maxim,max8907"; + reg = <0x3c>; + interrupts = <0 86 0x4>; + + maxim,system-power-controller; + + mbatt-supply = <&some_reg>; + in-v1-supply = <&mbatt_reg>; + ... + in1-supply = <&mbatt_reg>; + ... + + regulators { + mbatt_reg: mbatt { + regulator-name = "vbat_pmu"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + sd1 { + regulator-name = "nvvdd_sv1,vdd_cpu_pmu"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + sd2 { + regulator-name = "nvvdd_sv2,vdd_core"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; +... + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/max8925-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/max8925-regulator.txt new file mode 100644 index 000000000..0057695aa --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/max8925-regulator.txt @@ -0,0 +1,40 @@ +Max8925 Voltage regulators + +Required nodes: +-nodes: + - SDV1 for SDV SDV1 + - SDV2 for SDV SDV2 + - SDV3 for SDV SDV3 + - LDO1 for LDO LDO1 + - LDO2 for LDO LDO2 + - LDO3 for LDO LDO3 + - LDO4 for LDO LDO4 + - LDO5 for LDO LDO5 + - LDO6 for LDO LDO6 + - LDO7 for LDO LDO7 + - LDO8 for LDO LDO8 + - LDO9 for LDO LDO9 + - LDO10 for LDO LDO10 + - LDO11 for LDO LDO11 + - LDO12 for LDO LDO12 + - LDO13 for LDO LDO13 + - LDO14 for LDO LDO14 + - LDO15 for LDO LDO15 + - LDO16 for LDO LDO16 + - LDO17 for LDO LDO17 + - LDO18 for LDO LDO18 + - LDO19 for LDO LDO19 + - LDO20 for LDO LDO20 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + diff --git a/kernel/Documentation/devicetree/bindings/regulator/max8952.txt b/kernel/Documentation/devicetree/bindings/regulator/max8952.txt new file mode 100644 index 000000000..866fcdd0f --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/max8952.txt @@ -0,0 +1,52 @@ +Maxim MAX8952 voltage regulator + +Required properties: +- compatible: must be equal to "maxim,max8952" +- reg: I2C slave address, usually 0x60 +- max8952,dvs-mode-microvolt: array of 4 integer values defining DVS voltages + in microvolts. All values must be from range <770000, 1400000> +- any required generic properties defined in regulator.txt + +Optional properties: +- max8952,vid-gpios: array of two GPIO pins used for DVS voltage selection +- max8952,en-gpio: GPIO used to control enable status of regulator +- max8952,default-mode: index of default DVS voltage, from <0, 3> range +- max8952,sync-freq: sync frequency, must be one of following values: + - 0: 26 MHz + - 1: 13 MHz + - 2: 19.2 MHz + Defaults to 26 MHz if not specified. +- max8952,ramp-speed: voltage ramp speed, must be one of following values: + - 0: 32mV/us + - 1: 16mV/us + - 2: 8mV/us + - 3: 4mV/us + - 4: 2mV/us + - 5: 1mV/us + - 6: 0.5mV/us + - 7: 0.25mV/us + Defaults to 32mV/us if not specified. +- any available generic properties defined in regulator.txt + +Example: + + vdd_arm_reg: pmic@60 { + compatible = "maxim,max8952"; + reg = <0x60>; + + /* max8952-specific properties */ + max8952,vid-gpios = <&gpx0 3 0>, <&gpx0 4 0>; + max8952,en-gpio = <&gpx0 1 0>; + max8952,default-mode = <0>; + max8952,dvs-mode-microvolt = <1250000>, <1200000>, + <1050000>, <950000>; + max8952,sync-freq = <0>; + max8952,ramp-speed = <0>; + + /* generic regulator properties */ + regulator-name = "vdd_arm"; + regulator-min-microvolt = <770000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/max8973-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/max8973-regulator.txt new file mode 100644 index 000000000..4f15d8a1b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/max8973-regulator.txt @@ -0,0 +1,21 @@ +* Maxim MAX8973 Voltage Regulator + +Required properties: + +- compatible: must be "maxim,max8973" +- reg: the i2c slave address of the regulator. It should be 0x1b. + +Any standard regulator properties can be used to configure the single max8973 +DCDC. + +Example: + + max8973@1b { + compatible = "maxim,max8973"; + reg = <0x1b>; + + regulator-min-microvolt = <935000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/max8997-regulator.txt new file mode 100644 index 000000000..5c186a7a7 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/max8997-regulator.txt @@ -0,0 +1,146 @@ +* Maxim MAX8997 Voltage and Current Regulator + +The Maxim MAX8997 is a multi-function device which includes voltage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of max8997. + +Required properties: +- compatible: Should be "maxim,max8997-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- max8997,pmic-buck1-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck1 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- max8997,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- max8997,pmic-buck5-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck5 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +[1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional + property is specified, the 'max8997,pmic-buck[1/2/5]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from max8997 are delivered to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- max8997,pmic-buck1-uses-gpio-dvs: 'buck1' can be controlled by gpio dvs. +- max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- max8997,pmic-buck5-uses-gpio-dvs: 'buck5' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: +- max8997,pmic-ignore-gpiodvs-side-effect: When GPIO-DVS mode is used for + multiple bucks, changing the voltage value of one of the bucks may affect + that of another buck, which is the side effect of the change (set_voltage). + Use this property to ignore such side effects and change the voltage. + +- max8997,pmic-buck125-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- max8997,pmic-buck125-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of max8997 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + standard regulator bindings here + }; + +The following are the names of the regulators that the max8997 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of max8997. + + - LDOn + - valid values for n are 1 to 18 and 21 + - Example: LDO0, LD01, LDO2, LDO21 + - BUCKn + - valid values for n are 1 to 7. + - Example: BUCK1, BUCK2, BUCK3, BUCK7 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + + - CHARGER_CV: main battery charger voltage control + - CHARGER: main battery charger current control + - CHARGER_TOPOFF: end of charge current threshold level + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + max8997_pmic@66 { + compatible = "maxim,max8997-pmic"; + interrupt-parent = <&wakeup_eint>; + reg = <0x66>; + interrupts = <4 0>, <3 0>; + + max8997,pmic-buck1-uses-gpio-dvs; + max8997,pmic-buck2-uses-gpio-dvs; + max8997,pmic-buck5-uses-gpio-dvs; + + max8997,pmic-ignore-gpiodvs-side-effect; + max8997,pmic-buck125-default-dvs-idx = <0>; + + max8997,pmic-buck125-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>, /* SET2 */ + <&gpx0 2 1 0 0>; /* SET3 */ + + max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + max8997,pmic-buck2-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt new file mode 100644 index 000000000..a42b1d6e9 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt @@ -0,0 +1,217 @@ +Mediatek MT6397 Regulator Driver + +Required properties: +- compatible: "mediatek,mt6397-regulator" +- mt6397regulator: List of regulators provided by this controller. It is named + according to its regulator type, buck_<name> and ldo_<name>. + The definition for each of these nodes is defined using the standard binding + for regulators at Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are:: +BUCK: + buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu, + buck_vdrm, buck_vio18 +LDO: + ldo_vtcxo, ldo_va28, ldo_vcama, ldo_vio28, ldo_vusb, ldo_vmc, ldo_vmch, + ldo_vemc3v3, ldo_vgp1, ldo_vgp2, ldo_vgp3, ldo_vgp4, ldo_vgp5, ldo_vgp6, + ldo_vibr + +Example: + pmic { + compatible = "mediatek,mt6397"; + + mt6397regulator: mt6397regulator { + compatible = "mediatek,mt6397-regulator"; + + mt6397_vpca15_reg: buck_vpca15 { + regulator-compatible = "buck_vpca15"; + regulator-name = "vpca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <200>; + }; + + mt6397_vpca7_reg: buck_vpca7 { + regulator-compatible = "buck_vpca7"; + regulator-name = "vpca7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vsramca15_reg: buck_vsramca15 { + regulator-compatible = "buck_vsramca15"; + regulator-name = "vsramca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + + }; + + mt6397_vsramca7_reg: buck_vsramca7 { + regulator-compatible = "buck_vsramca7"; + regulator-name = "vsramca7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + + }; + + mt6397_vcore_reg: buck_vcore { + regulator-compatible = "buck_vcore"; + regulator-name = "vcore"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vgpu_reg: buck_vgpu { + regulator-compatible = "buck_vgpu"; + regulator-name = "vgpu"; + regulator-min-microvolt = < 700000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vdrm_reg: buck_vdrm { + regulator-compatible = "buck_vdrm"; + regulator-name = "vdrm"; + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <500>; + }; + + mt6397_vio18_reg: buck_vio18 { + regulator-compatible = "buck_vio18"; + regulator-name = "vio18"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2120000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <500>; + }; + + mt6397_vtcxo_reg: ldo_vtcxo { + regulator-compatible = "ldo_vtcxo"; + regulator-name = "vtcxo"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <90>; + }; + + mt6397_va28_reg: ldo_va28 { + regulator-compatible = "ldo_va28"; + regulator-name = "va28"; + /* fixed output 2.8 V */ + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vcama_reg: ldo_vcama { + regulator-compatible = "ldo_vcama"; + regulator-name = "vcama"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vio28_reg: ldo_vio28 { + regulator-compatible = "ldo_vio28"; + regulator-name = "vio28"; + /* fixed output 2.8 V */ + regulator-enable-ramp-delay = <240>; + }; + + mt6397_usb_reg: ldo_vusb { + regulator-compatible = "ldo_vusb"; + regulator-name = "vusb"; + /* fixed output 3.3 V */ + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vmc_reg: ldo_vmc { + regulator-compatible = "ldo_vmc"; + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vmch_reg: ldo_vmch { + regulator-compatible = "ldo_vmch"; + regulator-name = "vmch"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vemc_3v3_reg: ldo_vemc3v3 { + regulator-compatible = "ldo_vemc3v3"; + regulator-name = "vemc_3v3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp1_reg: ldo_vgp1 { + regulator-compatible = "ldo_vgp1"; + regulator-name = "vcamd"; + regulator-min-microvolt = <1220000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <240>; + }; + + mt6397_vgp2_reg: ldo_vgp2 { + egulator-compatible = "ldo_vgp2"; + regulator-name = "vcamio"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp3_reg: ldo_vgp3 { + regulator-compatible = "ldo_vgp3"; + regulator-name = "vcamaf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp4_reg: ldo_vgp4 { + regulator-compatible = "ldo_vgp4"; + regulator-name = "vgp4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp5_reg: ldo_vgp5 { + regulator-compatible = "ldo_vgp5"; + regulator-name = "vgp5"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp6_reg: ldo_vgp6 { + regulator-compatible = "ldo_vgp6"; + regulator-name = "vgp6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vibr_reg: ldo_vibr { + regulator-compatible = "ldo_vibr"; + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/kernel/Documentation/devicetree/bindings/regulator/palmas-pmic.txt new file mode 100644 index 000000000..725393c8a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -0,0 +1,82 @@ +* palmas regulator IP block devicetree bindings + +Required properties: +- compatible : Should be from the list + ti,twl6035-pmic + ti,twl6036-pmic + ti,twl6037-pmic + ti,tps65913-pmic + ti,tps65914-pmic + ti,tps65917-pmic +and also the generic series names + ti,palmas-pmic +- interrupt-parent : The parent interrupt controller which is palmas. +- interrupts : The interrupt number and the type which can be looked up here: + arch/arm/boot/dts/include/dt-bindings/interrupt-controller/irq.h +- interrupts-name: The names of the individual interrupts. + +Optional properties: +- ti,ldo6-vibrator : ldo6 is in vibrator mode + +Optional nodes: +- regulators : Must contain a sub-node per regulator from the list below. + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a + description of standard properties for these sub-nodes. + Additional custom properties are listed below. + + For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP, + smps45, smps457, smps7 depending on variant, smps6, smps[8-9], + smps10_out2, smps10_out1, ldo[1-9], ldoln, ldousb. + + Optional sub-node properties: + ti,warm-reset - maintain voltage during warm reset(boolean) + ti,roof-floor - This takes as optional argument on platform supporting + the rail from desired external control. If there is no argument then + it will be assume that it is controlled by NSLEEP pin. + The valid value for external pins are: + ENABLE1 then 1, + ENABLE2 then 2 or + NSLEEP then 3. + ti,mode-sleep - mode to adopt in pmic sleep 0 - off, 1 - auto, + 2 - eco, 3 - forced pwm + ti,smps-range - OTP has the wrong range set for the hardware so override + 0 - low range, 1 - high range. + +- ti,system-power-controller: Telling whether or not this pmic is controlling + the system power. + +Example: + +#include <dt-bindings/interrupt-controller/irq.h> + +pmic { + compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; + interrupt-parent = <&palmas>; + interrupts = <14 IRQ_TYPE_NONE>; + interrupts-name = "short-irq"; + + ti,ldo6-vibrator; + + ti,system-power-controller; + + regulators { + smps12_reg : smps12 { + regulator-name = "smps12"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,warm-reset; + ti,roof-floor = <1>; /* ENABLE1 control */ + ti,mode-sleep = <0>; + ti,smps-range = <1>; + }; + + ldo1_reg: ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/regulator/pbias-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/pbias-regulator.txt new file mode 100644 index 000000000..32aa26f1e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/pbias-regulator.txt @@ -0,0 +1,27 @@ +PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs. + +Required properties: +- compatible: + - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7. +- reg: pbias register offset from syscon base and size of pbias register. +- syscon : phandle of the system control module +- regulator-name : should be + pbias_mmc_omap2430 for OMAP2430, OMAP3 SoCs + pbias_sim_omap3 for OMAP3 SoCs + pbias_mmc_omap4 for OMAP4 SoCs + pbias_mmc_omap5 for OMAP5 and DRA7 SoC + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + pbias_regulator: pbias_regulator { + compatible = "ti,pbias-omap"; + reg = <0 0x4>; + syscon = <&omap5_padconf_global>; + pbias_mmc_reg: pbias_mmc_omap5 { + regulator-name = "pbias_mmc_omap5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/pfuze100.txt b/kernel/Documentation/devicetree/bindings/regulator/pfuze100.txt new file mode 100644 index 000000000..9b40db88f --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -0,0 +1,299 @@ +PFUZE100 family of regulators + +Required properties: +- compatible: "fsl,pfuze100", "fsl,pfuze200", "fsl,pfuze3000" +- reg: I2C slave address + +Required child node: +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Please refer to below doc + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + --PFUZE100 + sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6 + --PFUZE200 + sw1ab,sw2,sw3a,sw3b,swbst,vsnvs,vrefddr,vgen1~vgen6 + --PFUZE3000 + sw1a,sw1b,sw2,sw3,swbst,vsnvs,vrefddr,vldo1,vldo2,vccsd,v33,vldo3,vldo4 + +Each regulator is defined using the standard binding for regulators. + +Example 1: PFUZE100 + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + + +Example 2: PFUZE200 + + pmic: pfuze200@08 { + compatible = "fsl,pfuze200"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + +Example 3: PFUZE3000 + + pmic: pfuze3000@08 { + compatible = "fsl,pfuze3000"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1a { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + /* use sw1c_reg to align with pfuze100/pfuze200 */ + sw1c_reg: sw1b { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1650000>; + regulator-boot-on; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen2_reg: vldo2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vccsd { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: v33 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + }; + + vgen5_reg: vldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/pwm-regulator.txt new file mode 100644 index 000000000..ce91f61fe --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -0,0 +1,27 @@ +pwm regulator bindings + +Required properties: +- compatible: Should be "pwm-regulator" +- pwms: OF device-tree PWM specification (see PWM binding pwm.txt) +- voltage-table: voltage and duty table, include 2 members in each set of + brackets, first one is voltage(unit: uv), the next is duty(unit: percent) + +Any property defined as part of the core regulator binding defined in +regulator.txt can also be used. + +Example: + pwm_regulator { + compatible = "pwm-regulator; + pwms = <&pwm1 0 8448 0>; + + voltage-table = <1114000 0>, + <1095000 10>, + <1076000 20>, + <1056000 30>, + <1036000 40>, + <1016000 50>; + + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/regulator.txt new file mode 100644 index 000000000..abb26b58c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/regulator.txt @@ -0,0 +1,92 @@ +Voltage/Current Regulators + +Optional properties: +- regulator-name: A string used as a descriptive name for regulator outputs +- regulator-min-microvolt: smallest voltage consumers may set +- regulator-max-microvolt: largest voltage consumers may set +- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops +- regulator-min-microamp: smallest current consumers may set +- regulator-max-microamp: largest current consumers may set +- regulator-always-on: boolean, regulator should never be disabled +- regulator-boot-on: bootloader/firmware enabled regulator +- regulator-allow-bypass: allow the regulator to go into bypass mode +- <name>-supply: phandle to the parent supply/regulator node +- regulator-ramp-delay: ramp delay for regulator(in uV/uS) + For hardware which supports disabling ramp rate, it should be explicitly + intialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. +- regulator-enable-ramp-delay: The time taken, in microseconds, for the supply + rail to reach the target voltage, plus/minus whatever tolerance the board + design requires. This property describes the total system ramp time + required due to the combination of internal ramping of the regulator itself, + and board design issues such as trace capacitance and load on the supply. +- regulator-state-mem sub-root node for Suspend-to-RAM mode + : suspend to memory, the device goes to sleep, but all data stored in memory, + only some external interrupt can wake the device. +- regulator-state-disk sub-root node for Suspend-to-DISK mode + : suspend to disk, this state operates similarly to Suspend-to-RAM, + but includes a final step of writing memory contents to disk. +- regulator-state-[mem/disk] node has following common properties: + - regulator-on-in-suspend: regulator should be on in suspend state. + - regulator-off-in-suspend: regulator should be off in suspend state. + - regulator-suspend-microvolt: regulator should be set to this voltage + in suspend. + - regulator-mode: operating mode in the given suspend state. + The set of possible operating modes depends on the capabilities of + every hardware so the valid modes are documented on each regulator + device tree binding document. +- regulator-initial-mode: initial operating mode. The set of possible operating + modes depends on the capabilities of every hardware so each device binding + documentation explains which values the regulator supports. + +Deprecated properties: +- regulator-compatible: If a regulator chip contains multiple + regulators, and if the chip's binding contains a child node that + describes each regulator, then this property indicates which regulator + this child node is intended to configure. If this property is missing, + the node's name will be used instead. + +Example: + + xyzreg: regulator@0 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + vin-supply = <&vin>; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + +Regulator Consumers: +Consumer nodes can reference one or more of its supplies/ +regulators using the below bindings. + +- <name>-supply: phandle to the regulator node + +These are the same bindings that a regulator in the above +example used to reference its own supply, in which case +its just seen as a special case of a regulator being a +consumer itself. + +Example of a consumer device node (mmc) referencing two +regulators (twl_reg1 and twl_reg2), + + twl_reg1: regulator@0 { + ... + ... + ... + }; + + twl_reg2: regulator@1 { + ... + ... + ... + }; + + mmc: mmc@0x0 { + ... + ... + vmmc-supply = <&twl_reg1>; + vmmcaux-supply = <&twl_reg2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt new file mode 100644 index 000000000..20191315e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -0,0 +1,163 @@ +* Samsung S5M8767 Voltage and Current Regulator + +The Samsung S5M8767 is a multi-function device which includes voltage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of s5m8767. + +Required properties: +- compatible: Should be "samsung,s5m8767-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck3 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck4 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used + for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. + +[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s5m8767 are delivered to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. +- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: + +- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of s5m8767 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE_1.0V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + }; +The above regulator entries are defined in regulator bindings documentation +except these properties: + - op_mode: describes the different operating modes of the LDO's with + power mode change in SOC. The different possible values are, + 0 - always off mode + 1 - on in normal mode + 2 - low power mode + 3 - suspend mode + - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one + GPIO controlling this regulator (enable/disable); This is + valid only for buck9. + +The following are the names of the regulators that the s5m8767 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s5m8767. + + - LDOn + - valid values for n are 1 to 28 + - Example: LDO1, LDO2, LDO28 + - BUCKn + - valid values for n are 1 to 9. + - Example: BUCK1, BUCK2, BUCK9 + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + s5m8767_pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck2-uses-gpio-dvs; + s5m8767,pmic-buck3-uses-gpio-dvs; + s5m8767,pmic-buck4-uses-gpio-dvs; + + s5m8767,pmic-buck-default-dvs-idx = <0>; + + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */ + <&gpx0 1 0>, /* DVS2 */ + <&gpx0 2 0>; /* DVS3 */ + + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */ + <&gpx2 4 0>, /* SET2 */ + <&gpx2 5 0>; /* SET3 */ + + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + vemmc_reg: BUCK9 { + regulator-name = "VMEM_VDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <3>; /* Standby Mode */ + s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt new file mode 100644 index 000000000..f9acbc1f3 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt @@ -0,0 +1,18 @@ +SKY81452 voltage regulator + +Required properties: +- regulator node named lout. +- any required generic properties defined in regulator.txt + +Optional properties: +- any available generic properties defined in regulator.txt + +Example: + + regulator { + lout { + regulator-name = "sky81452-lout"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <8000000>; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt new file mode 100644 index 000000000..c58db75f9 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -0,0 +1,132 @@ +Adaptive Body Bias(ABB) SoC internal LDO regulator for Texas Instruments SoCs + +Required Properties: +- compatible: Should be one of: + - "ti,abb-v1" for older SoCs like OMAP3 + - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5 + - "ti,abb-v3" for a generic definition where setup and control registers are + provided (example: DRA7) +- reg: Address and length of the register set for the device. It contains + the information of registers in the same order as described by reg-names +- reg-names: Should contain the reg names + - "base-address" - contains base address of ABB module (ti,abb-v1,ti,abb-v2) + - "control-address" - contains control register address of ABB module (ti,abb-v3) + - "setup-address" - contains setup register address of ABB module (ti,abb-v3) + - "int-address" - contains address of interrupt register for ABB module + (also see Optional properties) +- #address-cell: should be 0 +- #size-cell: should be 0 +- clocks: should point to the clock node used by ABB module +- ti,settling-time: Settling time in uSecs from SoC documentation for ABB module + to settle down(target time for SR2_WTCNT_VALUE). +- ti,clock-cycles: SoC specific data about count of system ti,clock-cycles used for + computing settling time from SoC Documentation for ABB module(clock + cycles for SR2_WTCNT_VALUE). +- ti,tranxdone-status-mask: Mask to the int-register to write-to-clear mask + indicating LDO tranxdone (operation complete). +- ti,abb_info: An array of 6-tuples u32 items providing information about ABB + configuration needed per operational voltage of the device. + Each item consists of the following in the same order: + volt: voltage in uV - Only used to index ABB information. + ABB mode: one of the following: + 0-bypass + 1-Forward Body Bias(FBB) + 3-Reverse Body Bias(RBB) + efuse: (see Optional properties) + RBB enable efuse Mask: (See Optional properties) + FBB enable efuse Mask: (See Optional properties) + Vset value efuse Mask: (See Optional properties) + + NOTE: If more than 1 entry is present, then regulator is setup to change + voltage, allowing for various modes to be selected indexed off + the regulator. Further, ABB LDOs are considered always-on by + default. + +Optional Properties: +- reg-names: In addition to the required properties, the following are optional + - "efuse-address" - Contains efuse base address used to pick up ABB info. + - "ldo-address" - Contains address of ABB LDO overide register address. + "efuse-address" is required for this. +- ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override + register to provide override vset value. +- ti,ldovbb-override-mask - Required if ldo-address is set, mask for LDO + override register to enable override vset value. +- ti,abb_opp_sel: Addendum to the description in required properties + efuse: Mandatory if 'efuse-address' register is defined. Provides offset + from efuse-address to pick up ABB characteristics. Set to 0 if + 'efuse-address' is not defined. + RBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to RBB mode if value at "efuse-address" + + efuse maps to RBB mask. Set to 0 to ignore this. + FBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to FBB mode if value at "efuse-address" + + efuse maps to FBB mask (valid only if RBB mask does not match) + Set to 0 to ignore this. + Vset value efuse Mask: Mandatory if ldo-address is set. Picks up from + efuse the value to set in 'ti,ldovbb-vset-mask' at ldo-address. + +Example #1: Simplest configuration (no efuse data, hard coded ABB table): +abb_x: regulator-abb-x { + compatible = "ti,abb-v1"; + regulator-name = "abb_x"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x483072f0 0x8>, <0x48306818 0x4>; + reg-names = "base-address", "int-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <30>; + ti,clock-cycles = <8>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 1012500 0 0 0 0 0 /* Bypass */ + 1200000 3 0 0 0 0 /* RBB mandatory */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #2: Efuse bits contain ABB mode setting (no LDO override capability) +abb_y: regulator-abb-y { + compatible = "ti,abb-v2"; + regulator-name = "abb_y"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>; + reg-names = "base-address", "int-address", "efuse-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1012500 0 0 0x40000 0 0 /* RBB optional */ + 1200000 0 0x4 0 0x40000 0 /* FBB optional */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #3: Efuse bits contain ABB mode setting and LDO override capability +abb_z: regulator-abb-z { + compatible = "ti,abb-v2"; + regulator-name = "abb_z"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, + <0x4a002194 0x8>, <0x4ae0C314 0x4>; + reg-names = "base-address", "int-address", + "efuse-address", "ldo-address"; + ti,tranxdone-status-mask = <0x8000000>; + /* LDOVBBMM_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBMM_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1200000 0 0x4 0 0x40000 0x1f00 /* FBB optional, vset */ + >; +}; diff --git a/kernel/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt new file mode 100644 index 000000000..2f7e44a96 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt @@ -0,0 +1,27 @@ +TPS51632 Voltage regulators + +Required properties: +- compatible: Must be "ti,tps51632" +- reg: I2C slave address + +Optional properties: +- ti,enable-pwm-dvfs: Enable the DVFS voltage control through the PWM interface. +- ti,dvfs-step-20mV: The 20mV step voltage when PWM DVFS enabled. Missing this + will set 10mV step voltage in PWM DVFS mode. In normal mode, the voltage + step is 10mV as per datasheet. + +Any property defined as part of the core regulator binding, defined in +regulator.txt, can also be used. + +Example: + + tps51632 { + compatible = "ti,tps51632"; + reg = <0x43>; + regulator-name = "tps51632-vout"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + ti,enable-pwm-dvfs; + ti,dvfs-step-20mV; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt new file mode 100644 index 000000000..1b20c3dbc --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt @@ -0,0 +1,44 @@ +TPS62360 Voltage regulators + +Required properties: +- compatible: Must be one of the following. + "ti,tps62360" + "ti,tps62361", + "ti,tps62362", + "ti,tps62363", +- reg: I2C slave address + +Optional properties: +- ti,enable-vout-discharge: Enable output discharge. This is boolean value. +- ti,enable-pull-down: Enable pull down. This is boolean value. +- ti,vsel0-gpio: GPIO for controlling VSEL0 line. + If this property is missing, then assume that there is no GPIO + for vsel0 control. +- ti,vsel1-gpio: Gpio for controlling VSEL1 line. + If this property is missing, then assume that there is no GPIO + for vsel1 control. +- ti,vsel0-state-high: Initial state of vsel0 input is high. + If this property is missing, then assume the state as low (0). +- ti,vsel1-state-high: Initial state of vsel1 input is high. + If this property is missing, then assume the state as low (0). + +Any property defined as part of the core regulator binding, defined in +regulator.txt, can also be used. + +Example: + + abc: tps62360 { + compatible = "ti,tps62361"; + reg = <0x60>; + regulator-name = "tps62361-vout"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on + ti,vsel0-gpio = <&gpio1 16 0>; + ti,vsel1-gpio = <&gpio1 17 0>; + ti,vsel0-state-high; + ti,vsel1-state-high; + ti,enable-pull-down; + ti,enable-force-pwm; + ti,enable-vout-discharge; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/tps65090.txt b/kernel/Documentation/devicetree/bindings/regulator/tps65090.txt new file mode 100644 index 000000000..ca69f5e30 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -0,0 +1,126 @@ +TPS65090 regulators + +Required properties: +- compatible: "ti,tps65090" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + dcdc[1-3], fet[1-7] and ldo[1-2] respectively. +- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively. +- infet[1-7]-supply: The input supply for FET[1-7] respectively. +- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively. + +Optional properties: +- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled then this property should be there. +- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled and if it is from GPIO then GPIO + number should be provided. If it is externally controlled and no GPIO + entry then driver will just configure this rails as external control + and will not provide any enable/disable APIs. +- ti,overcurrent-wait: This is applicable to FET registers, which have a + poorly defined "overcurrent wait" field. If this property is present it + should be between 0 - 3. If this property isn't present we won't touch the + "overcurrent wait" field and we'll leave it to the BIOS/EC to deal with. + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps65090@48 { + compatible = "ti,tps65090"; + reg = <0x48>; + interrupts = <0 88 0x4>; + + vsys1-supply = <&some_reg>; + vsys2-supply = <&some_reg>; + vsys3-supply = <&some_reg>; + infet1-supply = <&some_reg>; + infet2-supply = <&some_reg>; + infet3-supply = <&some_reg>; + infet4-supply = <&some_reg>; + infet5-supply = <&some_reg>; + infet6-supply = <&some_reg>; + infet7-supply = <&some_reg>; + vsys-l1-supply = <&some_reg>; + vsys-l2-supply = <&some_reg>; + + regulators { + dcdc1 { + regulator-name = "dcdc1"; + regulator-boot-on; + regulator-always-on; + ti,enable-ext-control; + dcdc-ext-control-gpios = <&gpio 10 0>; + }; + + dcdc2 { + regulator-name = "dcdc2"; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3 { + regulator-name = "dcdc3"; + regulator-boot-on; + regulator-always-on; + }; + + fet1 { + regulator-name = "fet1"; + regulator-boot-on; + regulator-always-on; + }; + + fet2 { + regulator-name = "fet2"; + regulator-boot-on; + regulator-always-on; + }; + + fet3 { + regulator-name = "fet3"; + regulator-boot-on; + regulator-always-on; + }; + + fet4 { + regulator-name = "fet4"; + regulator-boot-on; + regulator-always-on; + }; + + fet5 { + regulator-name = "fet5"; + regulator-boot-on; + regulator-always-on; + }; + + fet6 { + regulator-name = "fet6"; + regulator-boot-on; + regulator-always-on; + }; + + fet7 { + regulator-name = "fet7"; + regulator-boot-on; + regulator-always-on; + }; + + ldo1 { + regulator-name = "ldo1"; + regulator-boot-on; + regulator-always-on; + }; + + ldo2 { + regulator-name = "ldo2"; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/tps65217.txt b/kernel/Documentation/devicetree/bindings/regulator/tps65217.txt new file mode 100644 index 000000000..4f05d208c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -0,0 +1,78 @@ +TPS65217 family of regulators + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- regulators: list of regulators provided by this controller, must be named + after their hardware counterparts: dcdc[1-3] and ldo[1-4] +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: +- ti,pmic-shutdown-controller: Telling the PMIC to shutdown on PWR_EN toggle. + + The valid names for regulators are: + tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + compatible = "ti,tps65217"; + ti,pmic-shutdown-controller; + + regulators { + dcdc1_reg: dcdc1 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: dcdc2 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: dcc3 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/tps65218.txt b/kernel/Documentation/devicetree/bindings/regulator/tps65218.txt new file mode 100644 index 000000000..fccc1d24a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/tps65218.txt @@ -0,0 +1,23 @@ +TPS65218 family of regulators + +Required properties: +For tps65218 regulators/LDOs +- compatible: + - "ti,tps65218-dcdc1" for DCDC1 + - "ti,tps65218-dcdc2" for DCDC2 + - "ti,tps65218-dcdc3" for DCDC3 + - "ti,tps65218-dcdc4" for DCDC4 + - "ti,tps65218-dcdc5" for DCDC5 + - "ti,tps65218-dcdc6" for DCDC6 + - "ti,tps65218-ldo1" for LDO1 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + xyz: regulator@0 { + compatible = "ti,tps65218-dcdc1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/tps6586x.txt b/kernel/Documentation/devicetree/bindings/regulator/tps6586x.txt new file mode 100644 index 000000000..8b40cac24 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -0,0 +1,135 @@ +TPS6586x family of regulators + +Required properties: +- compatible: "ti,tps6586x" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- #gpio-cells: number of cells to describe a GPIO +- gpio-controller: mark the device as a GPIO controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + sys, sm[0-2], ldo[0-9] and ldo_rtc +- sys-supply: The input supply for SYS. +- vin-sm0-supply: The input supply for the SM0. +- vin-sm1-supply: The input supply for the SM1. +- vin-sm2-supply: The input supply for the SM2. +- vinldo01-supply: The input supply for the LDO1 and LDO2 +- vinldo23-supply: The input supply for the LDO2 and LDO3 +- vinldo4-supply: The input supply for the LDO4 +- vinldo678-supply: The input supply for the LDO6, LDO7 and LDO8 +- vinldo9-supply: The input supply for the LDO9 + +Optional properties: +- ti,system-power-controller: Telling whether or not this pmic is controlling + the system power. + +Each regulator is defined using the standard binding for regulators. + +Note: LDO5 and LDO_RTC is supplied by SYS regulator internally and driver + take care of making proper parent child relationship. + +Example: + + pmu: tps6586x@34 { + compatible = "ti,tps6586x"; + reg = <0x34>; + interrupts = <0 88 0x4>; + + #gpio-cells = <2>; + gpio-controller; + + ti,system-power-controller; + + sys-supply = <&some_reg>; + vin-sm0-supply = <&some_reg>; + vin-sm1-supply = <&some_reg>; + vin-sm2-supply = <&some_reg>; + vinldo01-supply = <...>; + vinldo23-supply = <...>; + vinldo4-supply = <...>; + vinldo678-supply = <...>; + vinldo9-supply = <...>; + + regulators { + sys_reg: sys { + regulator-name = "vdd_sys"; + regulator-boot-on; + regulator-always-on; + }; + + sm0_reg: sm0 { + regulator-min-microvolt = < 725000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + sm1_reg: sm1 { + regulator-min-microvolt = < 725000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + sm2_reg: sm2 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <4550000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo0_reg: ldo0 { + regulator-name = "PCIE CLK"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo1_reg: ldo1 { + regulator-min-microvolt = < 725000>; + regulator-max-microvolt = <1500000>; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = < 725000>; + regulator-max-microvolt = <1500000>; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <3300000>; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2475000>; + }; + + ldo5_reg: ldo5 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <3300000>; + }; + + ldo6_reg: ldo6 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <3300000>; + }; + + ldo7_reg: ldo7 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <3300000>; + }; + + ldo8_reg: ldo8 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <3300000>; + }; + + ldo9_reg: ldo9 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/twl-regulator.txt new file mode 100644 index 000000000..75b0c1669 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -0,0 +1,67 @@ +TWL family of regulators + +Required properties: +For twl6030 regulators/LDOs +- compatible: + - "ti,twl6030-vaux1" for VAUX1 LDO + - "ti,twl6030-vaux2" for VAUX2 LDO + - "ti,twl6030-vaux3" for VAUX3 LDO + - "ti,twl6030-vmmc" for VMMC LDO + - "ti,twl6030-vpp" for VPP LDO + - "ti,twl6030-vusim" for VUSIM LDO + - "ti,twl6030-vana" for VANA LDO + - "ti,twl6030-vcxio" for VCXIO LDO + - "ti,twl6030-vdac" for VDAC LDO + - "ti,twl6030-vusb" for VUSB LDO + - "ti,twl6030-v1v8" for V1V8 LDO + - "ti,twl6030-v2v1" for V2V1 LDO + - "ti,twl6030-vdd1" for VDD1 SMPS + - "ti,twl6030-vdd2" for VDD2 SMPS + - "ti,twl6030-vdd3" for VDD3 SMPS +For twl6032 regulators/LDOs +- compatible: + - "ti,twl6032-ldo1" for LDO1 LDO + - "ti,twl6032-ldo2" for LDO2 LDO + - "ti,twl6032-ldo3" for LDO3 LDO + - "ti,twl6032-ldo4" for LDO4 LDO + - "ti,twl6032-ldo5" for LDO5 LDO + - "ti,twl6032-ldo6" for LDO6 LDO + - "ti,twl6032-ldo7" for LDO7 LDO + - "ti,twl6032-ldoln" for LDOLN LDO + - "ti,twl6032-ldousb" for LDOUSB LDO + - "ti,twl6032-smps3" for SMPS3 SMPS + - "ti,twl6032-smps4" for SMPS4 SMPS + - "ti,twl6032-vio" for VIO SMPS +For twl4030 regulators/LDOs +- compatible: + - "ti,twl4030-vaux1" for VAUX1 LDO + - "ti,twl4030-vaux2" for VAUX2 LDO + - "ti,twl5030-vaux2" for VAUX2 LDO + - "ti,twl4030-vaux3" for VAUX3 LDO + - "ti,twl4030-vaux4" for VAUX4 LDO + - "ti,twl4030-vmmc1" for VMMC1 LDO + - "ti,twl4030-vmmc2" for VMMC2 LDO + - "ti,twl4030-vpll1" for VPLL1 LDO + - "ti,twl4030-vpll2" for VPLL2 LDO + - "ti,twl4030-vsim" for VSIM LDO + - "ti,twl4030-vdac" for VDAC LDO + - "ti,twl4030-vintana2" for VINTANA2 LDO + - "ti,twl4030-vio" for VIO LDO + - "ti,twl4030-vdd1" for VDD1 SMPS + - "ti,twl4030-vdd2" for VDD2 SMPS + - "ti,twl4030-vintana1" for VINTANA1 LDO + - "ti,twl4030-vintdig" for VINTDIG LDO + - "ti,twl4030-vusb1v5" for VUSB1V5 LDO + - "ti,twl4030-vusb1v8" for VUSB1V8 LDO + - "ti,twl4030-vusb3v1" for VUSB3V1 LDO + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + xyz: regulator@0 { + compatible = "ti,twl6030-vaux1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + }; diff --git a/kernel/Documentation/devicetree/bindings/regulator/vexpress.txt b/kernel/Documentation/devicetree/bindings/regulator/vexpress.txt new file mode 100644 index 000000000..d775f7248 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/regulator/vexpress.txt @@ -0,0 +1,32 @@ +Versatile Express voltage regulators +------------------------------------ + +Requires node properties: +- "compatible" value: "arm,vexpress-volt" +- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg + (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt + for more details) + +Required regulator properties: +- "regulator-name" +- "regulator-always-on" + +Optional regulator properties: +- "regulator-min-microvolt" +- "regulator-max-microvolt" + +See Documentation/devicetree/bindings/regulator/regulator.txt +for more details about the regulator properties. + +When no "regulator-[min|max]-microvolt" properties are defined, +the device is treated as fixed (or rather "read-only") regulator. + +Example: + volt@0 { + compatible = "arm,vexpress-volt"; + arm,vexpress-sysreg,func = <2 0>; + regulator-name = "Cores"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + }; |