diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/pwm')
28 files changed, 806 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt new file mode 100644 index 000000000..cfda0d57d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for Atmel's HLCDC (High-end LCD Controller) PWM driver + +The Atmel HLCDC PWM is subdevice of the HLCDC MFD device. +See ../mfd/atmel-hlcdc.txt for more details. + +Required properties: + - compatible: value should be one of the following: + "atmel,hlcdc-pwm" + - pinctr-names: the pin control state names. Should contain "default". + - pinctrl-0: should contain the pinctrl states described by pinctrl + default. + - #pwm-cells: should be set to 3. This PWM chip use the default 3 cells + bindings defined in pwm.txt in this directory. + +Example: + + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/atmel-pwm.txt new file mode 100644 index 000000000..02331b904 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/atmel-pwm.txt @@ -0,0 +1,33 @@ +Atmel PWM controller + +Required properties: + - compatible: should be one of: + - "atmel,at91sam9rl-pwm" + - "atmel,sama5d3-pwm" + - reg: physical base address and length of the controller's registers + - #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Example: + + pwm0: pwm@f8034000 { + compatible = "atmel,at91sam9rl-pwm"; + reg = <0xf8034000 0x400>; + #pwm-cells = <3>; + }; + + pwmleds { + compatible = "pwm-leds"; + + d1 { + label = "d1"; + pwms = <&pwm0 3 5000 0> + max-brightness = <255>; + }; + + d2 { + label = "d2"; + pwms = <&pwm0 1 5000 1> + max-brightness = <255>; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt new file mode 100644 index 000000000..8031148bc --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt @@ -0,0 +1,16 @@ +Atmel TCB PWM controller + +Required properties: +- compatible: should be "atmel,tcb-pwm" +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. +- tc-block: The Timer Counter block to use as a PWM chip. + +Example: + +pwm { + compatible = "atmel,tcb-pwm"; + #pwm-cells = <3>; + tc-block = <1>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt new file mode 100644 index 000000000..8eae9fe78 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt @@ -0,0 +1,21 @@ +Broadcom Kona PWM controller device tree bindings + +This controller has 6 channels. + +Required Properties : +- compatible: should contain "brcm,kona-pwm" +- reg: physical base address and length of the controller's registers +- clocks: phandle + clock specifier pair for the external clock +- #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + +pwm: pwm@3e01a000 { + compatible = "brcm,bcm11351-pwm", "brcm,kona-pwm"; + reg = <0x3e01a000 0xc4>; + clocks = <&pwm_clk>; + #pwm-cells = <3>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt new file mode 100644 index 000000000..a183db48f --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt @@ -0,0 +1,16 @@ +* Cirris Logic CLPS711X PWM controller + +Required properties: +- compatible: Shall contain "cirrus,clps711x-pwm". +- reg: Physical base address and length of the controller's registers. +- clocks: phandle + clock specifier pair of the PWM reference clock. +- #pwm-cells: Should be 1. The cell specifies the index of the channel. + +Example: + pwm: pwm@80000400 { + compatible = "cirrus,ep7312-pwm", + "cirrus,clps711x-pwm"; + reg = <0x80000400 0x4>; + clocks = <&clks 8>; + #pwm-cells = <1>; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/img-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/img-pwm.txt new file mode 100644 index 000000000..fade5f26f --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/img-pwm.txt @@ -0,0 +1,24 @@ +*Imagination Technologies PWM DAC driver + +Required properties: + - compatible: Should be "img,pistachio-pwm" + - reg: Should contain physical base address and length of pwm registers. + - clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. + - clock-names: Must include the following entries. + - pwm: PWM operating clock. + - sys: PWM system interface clock. + - #pwm-cells: Should be 2. See pwm.txt in this directory for the + description of the cells format. + - img,cr-periph: Must contain a phandle to the peripheral control + syscon node which contains PWM control registers. + +Example: + pwm: pwm@18101300 { + compatible = "img,pistachio-pwm"; + reg = <0x18101300 0x100>; + clocks = <&pwm_clk>, <&system_clk>; + clock-names = "pwm", "sys"; + #pwm-cells = <2>; + img,cr-periph = <&cr_periph>; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/imx-pwm.txt new file mode 100644 index 000000000..e00c2e9f4 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/imx-pwm.txt @@ -0,0 +1,27 @@ +Freescale i.MX PWM controller + +Required properties: +- compatible : should be "fsl,<soc>-pwm" and one of the following + compatible strings: + - "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1 + - "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27 +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. +- clocks : Clock specifiers for both ipg and per clocks. +- clock-names : Clock names should include both "ipg" and "per" +See the clock consumer binding, + Documentation/devicetree/bindings/clock/clock-bindings.txt +- interrupts: The interrupt for the pwm controller + +Example: + +pwm1: pwm@53fb4000 { + #pwm-cells = <2>; + compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; + reg = <0x53fb4000 0x4000>; + clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>, + <&clks IMX5_CLK_PWM1_HF_GATE>; + clock-names = "ipg", "per"; + interrupts = <61>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt new file mode 100644 index 000000000..cfe1db3bb --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt @@ -0,0 +1,12 @@ +LPC32XX PWM controller + +Required properties: +- compatible: should be "nxp,lpc3220-pwm" +- reg: physical base address and length of the controller's registers + +Examples: + +pwm@0x4005C000 { + compatible = "nxp,lpc3220-pwm"; + reg = <0x4005C000 0x8>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/mxs-pwm.txt new file mode 100644 index 000000000..96cdde5f6 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/mxs-pwm.txt @@ -0,0 +1,17 @@ +Freescale MXS PWM controller + +Required properties: +- compatible: should be "fsl,imx23-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. +- fsl,pwm-number: the number of PWM devices + +Example: + +pwm: pwm@80064000 { + compatible = "fsl,imx28-pwm", "fsl,imx23-pwm"; + reg = <0x80064000 0x2000>; + #pwm-cells = <2>; + fsl,pwm-number = <8>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt new file mode 100644 index 000000000..c52f03b50 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt @@ -0,0 +1,27 @@ +Tegra SoC PWFM controller + +Required properties: +- compatible: For Tegra20, must contain "nvidia,tegra20-pwm". For Tegra30, + must contain "nvidia,tegra30-pwm". Otherwise, must contain + "nvidia,<chip>-pwm", plus one of the above, where <chip> is tegra114, + tegra124, tegra132, or tegra210. +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pwm + +Example: + + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + clocks = <&tegra_car 17>; + resets = <&tegra_car 17>; + reset-names = "pwm"; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt new file mode 100644 index 000000000..f84ec9d29 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt @@ -0,0 +1,27 @@ +NXP PCA9685 16-channel 12-bit PWM LED controller +================================================ + +Required properties: + - compatible: "nxp,pca9685-pwm" + - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of + the cells format. + The index 16 is the ALLCALL channel, that sets all PWM channels at the same + time. + +Optional properties: + - invert (bool): boolean to enable inverted logic + - open-drain (bool): boolean to configure outputs with open-drain structure; + if omitted use totem-pole structure + +Example: + +For LEDs that are directly connected to the PCA, the following setting is +applicable: + +pca: pca@41 { + compatible = "nxp,pca9685-pwm"; + #pwm-cells = <2>; + reg = <0x41>; + invert; + open-drain; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt new file mode 100644 index 000000000..fb6fb31bc --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt @@ -0,0 +1,30 @@ +BCM2835 PWM controller (Raspberry Pi controller) + +Required properties: +- compatible: should be "brcm,bcm2835-pwm" +- reg: physical base address and length of the controller's registers +- clock: This clock defines the base clock frequency of the PWM hardware + system, the period and the duty_cycle of the PWM signal is a multiple of + the base period. +- #pwm-cells: Should be 2. See pwm.txt in this directory for a description of + the cells format. + +Examples: + +pwm@2020c000 { + compatible = "brcm,bcm2835-pwm"; + reg = <0x2020c000 0x28>; + clocks = <&clk_pwm>; + #pwm-cells = <2>; +}; + +clocks { + .... + clk_pwm: pwm { + compatible = "fixed-clock"; + reg = <3>; + #clock-cells = <0>; + clock-frequency = <9200000>; + }; + .... +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt new file mode 100644 index 000000000..3899d6a55 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt @@ -0,0 +1,52 @@ +Freescale FlexTimer Module (FTM) PWM controller + +The same FTM PWM device can have a different endianness on different SoCs. The +device tree provides a property to describing this so that an operating system +device driver can handle all variants of the device. Refer to the table below +for the endianness of the FTM PWM block as integrated into the existing SoCs: + + SoC | FTM-PWM endianness + --------+------------------- + Vybrid | LE + LS1 | BE + LS2 | LE + +Please see ../regmap/regmap.txt for more detail about how to specify endian +modes in device tree. + + +Required properties: +- compatible: Should be "fsl,vf610-ftm-pwm". +- reg: Physical base address and length of the controller's registers +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. +- clock-names: Should include the following module clock source entries: + "ftm_sys" (module clock, also can be used as counter clock), + "ftm_ext" (external counter clock), + "ftm_fix" (fixed counter clock), + "ftm_cnt_clk_en" (external and fixed counter clock enable/disable). +- clocks: Must contain a phandle and clock specifier for each entry in + clock-names, please see clock/clock-bindings.txt for details of the property + values. +- pinctrl-names: Must contain a "default" entry. +- pinctrl-NNN: One property must exist for each entry in pinctrl-names. + See pinctrl/pinctrl-bindings.txt for details of the property values. +- big-endian: Boolean property, required if the FTM PWM registers use a big- + endian rather than little-endian layout. + +Example: + +pwm0: pwm@40038000 { + compatible = "fsl,vf610-ftm-pwm"; + reg = <0x40038000 0x1000>; + #pwm-cells = <3>; + clock-names = "ftm_sys", "ftm_ext", + "ftm_fix", "ftm_cnt_clk_en"; + clocks = <&clks VF610_CLK_FTM0>, + <&clks VF610_CLK_FTM0_EXT_SEL>, + <&clks VF610_CLK_FTM0_FIX_SEL>, + <&clks VF610_CLK_FTM0_EXT_FIX_EN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_1>; + big-endian; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt new file mode 100644 index 000000000..7bd9d3b12 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt @@ -0,0 +1,58 @@ +TI/National Semiconductor LP3943 PWM controller + +Required properties: + - compatible: "ti,lp3943-pwm" + - #pwm-cells: Should be 2. See pwm.txt in this directory for a + description of the cells format. + Note that this hardware limits the period length to the + range 6250~1600000. + - ti,pwm0 or ti,pwm1: Output pin number(s) for PWM channel 0 or 1. + 0 = output 0 + 1 = output 1 + . + . + 15 = output 15 + +Example: +PWM 0 is for RGB LED brightness control +PWM 1 is for brightness control of LP8557 backlight device + +&i2c3 { + lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + /* + * PWM 0 : output 8, 9 and 10 + * PWM 1 : output 15 + */ + pwm3943: pwm { + compatible = "ti,lp3943-pwm"; + #pwm-cells = <2>; + ti,pwm0 = <8 9 10>; + ti,pwm1 = <15>; + }; + }; + +}; + +/* LEDs control with PWM 0 of LP3943 */ +pwmleds { + compatible = "pwm-leds"; + rgb { + label = "indi::rgb"; + pwms = <&pwm3943 0 10000>; + max-brightness = <255>; + }; +}; + +&i2c4 { + /* Backlight control with PWM 1 of LP3943 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + + pwms = <&pwm3943 1 10000>; + pwm-names = "lp8557"; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt new file mode 100644 index 000000000..b8be3d09e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt @@ -0,0 +1,20 @@ +Rockchip PWM controller + +Required properties: + - compatible: should be "rockchip,<name>-pwm" + "rockchip,rk2928-pwm": found on RK29XX,RK3066 and RK3188 SoCs + "rockchip,rk3288-pwm": found on RK3288 SoC + "rockchip,vop-pwm": found integrated in VOP on RK3288 SoC + - reg: physical base address and length of the controller's registers + - clocks: phandle and clock specifier of the PWM reference clock + - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory + for a description of the cell format. + +Example: + + pwm0: pwm@20030000 { + compatible = "rockchip,rk2928-pwm"; + reg = <0x20030000 0x10>; + clocks = <&cru PCLK_PWM01>; + #pwm-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-samsung.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-samsung.txt new file mode 100644 index 000000000..5538de9c2 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-samsung.txt @@ -0,0 +1,51 @@ +* Samsung PWM timers + +Samsung SoCs contain PWM timer blocks which can be used for system clock source +and clock event timers, as well as to drive SoC outputs with PWM signal. Each +PWM timer block provides 5 PWM channels (not all of them can drive physical +outputs - see SoC and board manual). + +Be aware that the clocksource driver supports only uniprocessor systems. + +Required properties: +- compatible : should be one of following: + samsung,s3c2410-pwm - for 16-bit timers present on S3C24xx SoCs + samsung,s3c6400-pwm - for 32-bit timers present on S3C64xx SoCs + samsung,s5p6440-pwm - for 32-bit timers present on S5P64x0 SoCs + samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210, + Exynos4210 rev0 SoCs + samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210, + Exynos4x12, Exynos5250 and Exynos5420 SoCs +- reg: base address and size of register area +- interrupts: list of timer interrupts (one interrupt per timer, starting at + timer 0) +- clock-names: should contain all following required clock names: + - "timers" - PWM base clock used to generate PWM signals, + and any subset of following optional clock names: + - "pwm-tclk0" - first external PWM clock source, + - "pwm-tclk1" - second external PWM clock source. + Note that not all IP variants allow using all external clock sources. + Refer to SoC documentation to learn which clock source configurations + are available. +- clocks: should contain clock specifiers of all clocks, which input names + have been specified in clock-names property, in same order. +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. + +Optional properties: +- samsung,pwm-outputs: list of PWM channels used as PWM outputs on particular + platform - an array of up to 5 elements being indices of PWM channels + (from 0 to 4), the order does not matter. + +Example: + pwm@7f006000 { + compatible = "samsung,s3c6400-pwm"; + reg = <0x7f006000 0x1000>; + interrupt-parent = <&vic0>; + interrupts = <23>, <24>, <25>, <27>, <28>; + clocks = <&clock 67>; + clock-names = "timers"; + samsung,pwm-outputs = <0>, <1>; + #pwm-cells = <3>; + } diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-st.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-st.txt new file mode 100644 index 000000000..84d2fb807 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-st.txt @@ -0,0 +1,41 @@ +STMicroelectronics PWM driver bindings +-------------------------------------- + +Required parameters: +- compatible : "st,pwm" +- #pwm-cells : Number of cells used to specify a PWM. First cell + specifies the per-chip index of the PWM to use and the + second cell is the period in nanoseconds - fixed to 2 + for STiH41x. +- reg : Physical base address and length of the controller's + registers. +- pinctrl-names: Set to "default". +- pinctrl-0: List of phandles pointing to pin configuration nodes + for PWM module. + For Pinctrl properties, please refer to [1]. +- clock-names: Set to "pwm". +- clocks: phandle of the clock used by the PWM module. + For Clk properties, please refer to [2]. + +Optional properties: +- st,pwm-num-chan: Number of available channels. If not passed, the driver + will consider single channel by default. + +[1] Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Example: + +pwm1: pwm@fe510000 { + compatible = "st,pwm"; + reg = <0xfe510000 0x68>; + #pwm-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1_chan0_default + &pinctrl_pwm1_chan1_default + &pinctrl_pwm1_chan2_default + &pinctrl_pwm1_chan3_default>; + clocks = <&clk_sysin>; + clock-names = "pwm"; + st,pwm-num-chan = <4>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt new file mode 100644 index 000000000..ae0273e19 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt @@ -0,0 +1,20 @@ +Allwinner sun4i and sun7i SoC PWM controller + +Required properties: + - compatible: should be one of: + - "allwinner,sun4i-a10-pwm" + - "allwinner,sun7i-a20-pwm" + - reg: physical base address and length of the controller's registers + - #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. + - clocks: From common clock binding, handle to the parent clock. + +Example: + + pwm: pwm@01c20e00 { + compatible = "allwinner,sun7i-a20-pwm"; + reg = <0x01c20e00 0xc>; + clocks = <&osc24M>; + #pwm-cells = <3>; + status = "disabled"; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt new file mode 100644 index 000000000..fb81179dc --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -0,0 +1,29 @@ +TI SOC ECAP based APWM controller + +Required properties: +- compatible: Must be "ti,<soc>-ecap". + for am33xx - compatible = "ti,am33xx-ecap"; + for da850 - compatible = "ti,da850-ecap", "ti,am33xx-ecap"; +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The PWM channel index ranges from 0 to 4. The only third + cell flag supported by this binding is PWM_POLARITY_INVERTED. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the ECAP: + "ecap<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ecap0: ecap@0 { /* ECAP on am33xx */ + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; +}; + +ecap0: ecap@0 { /* ECAP on da850 */ + compatible = "ti,da850-ecap", "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x306000 0x80>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt new file mode 100644 index 000000000..9c100b2c5 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -0,0 +1,29 @@ +TI SOC EHRPWM based PWM controller + +Required properties: +- compatible: Must be "ti,<soc>-ehrpwm". + for am33xx - compatible = "ti,am33xx-ehrpwm"; + for da850 - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm"; +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the EHRPWM: + "ehrpwm<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ehrpwm0: ehrpwm@0 { /* EHRPWM on am33xx */ + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x100>; + ti,hwmods = "ehrpwm0"; +}; + +ehrpwm0: ehrpwm@0 { /* EHRPWM on da850 */ + compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x300000 0x2000>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt new file mode 100644 index 000000000..f7eae77f8 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -0,0 +1,31 @@ +TI SOC based PWM Subsystem + +Required properties: +- compatible: Must be "ti,am33xx-pwmss"; +- reg: physical base address and size of the registers map. +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. +- ranges: describes the address mapping of a memory-mapped bus. Should set to + physical address map of child's base address, physical address within + parent's address space and length of the address map. For am33xx, + 3 set of child register maps present, ECAP register space, EQEP + register space, EHRPWM register space. + +Also child nodes should also populated under PWMSS DT node. + +Example: +pwmss0: pwmss@48300000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/pwm.txt new file mode 100644 index 000000000..8556263b8 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pwm.txt @@ -0,0 +1,69 @@ +Specifying PWM information for devices +====================================== + +1) PWM user nodes +----------------- + +PWM users should specify a list of PWM devices that they want to use +with a property containing a 'pwm-list': + + pwm-list ::= <single-pwm> [pwm-list] + single-pwm ::= <pwm-phandle> <pwm-specifier> + pwm-phandle : phandle to PWM controller node + pwm-specifier : array of #pwm-cells specifying the given PWM + (controller specific) + +PWM properties should be named "pwms". The exact meaning of each pwms +property must be documented in the device tree binding for each device. +An optional property "pwm-names" may contain a list of strings to label +each of the PWM devices listed in the "pwms" property. If no "pwm-names" +property is given, the name of the user node will be used as fallback. + +Drivers for devices that use more than a single PWM device can use the +"pwm-names" property to map the name of the PWM device requested by the +pwm_get() call to an index into the list given by the "pwms" property. + +The following example could be used to describe a PWM-based backlight +device: + + pwm: pwm { + #pwm-cells = <2>; + }; + + [...] + + bl: backlight { + pwms = <&pwm 0 5000000>; + pwm-names = "backlight"; + }; + +Note that in the example above, specifying the "pwm-names" is redundant +because the name "backlight" would be used as fallback anyway. + +pwm-specifier typically encodes the chip-relative PWM number and the PWM +period in nanoseconds. + +Optionally, the pwm-specifier can encode a number of flags (defined in +<dt-bindings/pwm/pwm.h>) in a third cell: +- PWM_POLARITY_INVERTED: invert the PWM signal polarity + +Example with optional PWM specifier for inverse polarity + + bl: backlight { + pwms = <&pwm 0 5000000 PWM_POLARITY_INVERTED>; + pwm-names = "backlight"; + }; + +2) PWM controller nodes +----------------------- + +PWM controller nodes must specify the number of cells used for the +specifier using the '#pwm-cells' property. + +An example PWM controller might look like this: + + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/pxa-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/pxa-pwm.txt new file mode 100644 index 000000000..5ae9f1e3c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/pxa-pwm.txt @@ -0,0 +1,30 @@ +Marvell PWM controller + +Required properties: +- compatible: should be one or more of: + - "marvell,pxa250-pwm" + - "marvell,pxa270-pwm" + - "marvell,pxa168-pwm" + - "marvell,pxa910-pwm" +- reg: Physical base address and length of the registers used by the PWM channel + Note that one device instance must be created for each PWM that is used, so the + length covers only the register window for one PWM output, not that of the + entire PWM controller. Currently length is 0x10 for all supported devices. +- #pwm-cells: Should be 1. This cell is used to specify the period in + nanoseconds. + +Example PWM device node: + +pwm0: pwm@40b00000 { + compatible = "marvell,pxa250-pwm"; + reg = <0x40b00000 0x10>; + #pwm-cells = <1>; +}; + +Example PWM client node: + +backlight { + compatible = "pwm-backlight"; + pwms = <&pwm0 5000000>; + ... +} diff --git a/kernel/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt new file mode 100644 index 000000000..b067e84a9 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt @@ -0,0 +1,28 @@ +* Renesas R-Car Timer Pulse Unit PWM Controller + +Required Properties: + + - compatible: should be one of the following. + - "renesas,tpu-r8a73a4": for R8A77A4 (R-Mobile APE6) compatible PWM controller. + - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller. + - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller. + - "renesas,tpu-sh7372": for SH7372 (SH-Mobile AP4) compatible PWM controller. + - "renesas,tpu": for generic R-Car TPU PWM controller. + + - reg: Base address and length of each memory resource used by the PWM + controller hardware module. + + - #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. + +Please refer to pwm.txt in this directory for details of the common PWM bindings +used by client devices. + +Example: R8A7740 (R-Car A1) TPU controller node + + tpu: pwm@e6600000 { + compatible = "renesas,tpu-r8a7740", "renesas,tpu"; + reg = <0xe6600000 0x100>; + #pwm-cells = <3>; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/spear-pwm.txt new file mode 100644 index 000000000..b486de2c3 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/spear-pwm.txt @@ -0,0 +1,17 @@ +== ST SPEAr SoC PWM controller == + +Required properties: +- compatible: should be one of: + - "st,spear320-pwm" + - "st,spear1340-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. + +Example: + + pwm: pwm@a8000000 { + compatible ="st,spear320-pwm"; + reg = <0xa8000000 0x1000>; + #pwm-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt new file mode 100644 index 000000000..4e32bee11 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers + +Supported PWMs: +On TWL4030 series: PWM1 and PWM2 +On TWL6030 series: PWM0 and PWM1 + +Required properties: +- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. + +Example: + +twl_pwm: pwm { + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/kernel/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt new file mode 100644 index 000000000..9f4b46090 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers connected to LED terminals + +Supported PWMs: +On TWL4030 series: PWMA and PWMB (connected to LEDA and LEDB terminals) +On TWL6030 series: LED PWM (mainly used as charging indicator LED) + +Required properties: +- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. + +Example: + +twl_pwmled: pwmled { + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/kernel/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt new file mode 100644 index 000000000..a76390e6d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -0,0 +1,18 @@ +VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller + +Required properties: +- compatible: should be "via,vt8500-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. +- clocks: phandle to the PWM source clock + +Example: + +pwm1: pwm@d8220000 { + #pwm-cells = <3>; + compatible = "via,vt8500-pwm"; + reg = <0xd8220000 0x1000>; + clocks = <&clkpwm>; +}; |