summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt')
-rw-r--r--kernel/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt227
1 files changed, 227 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/kernel/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt
new file mode 100644
index 000000000..509faa87a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt
@@ -0,0 +1,227 @@
+ImgTec TZ1090 pin controller
+
+Required properties:
+- compatible: "img,tz1090-pinctrl"
+- reg: Should contain the register physical address and length of the pad
+ configuration registers (CR_PADS_* and CR_IF_CTL0).
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+TZ1090's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function. For this reason, even seemingly boolean
+values are actually tristates in this binding: unspecified, off, or on.
+Unspecified is represented as an absent property, and off/on are represented as
+integer values 0 and 1.
+
+Required subnode-properties:
+- tz1090,pins : An array of strings. Each string contains the name of a pin or
+ group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- tz1090,function: A string containing the name of the function to mux to the
+ pin or group. Valid values for function names are listed below, including
+ which pingroups can be muxed to them.
+- supported generic pinconfig properties (for further details see
+ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt):
+ - bias-disable
+ - bias-high-impedance
+ - bias-bus-hold
+ - bias-pull-up
+ - bias-pull-down
+ - input-schmitt-enable
+ - input-schmitt-disable
+ - drive-strength: Integer, control drive strength of pins in mA.
+ 2: 2mA
+ 4: 4mA
+ 8: 8mA
+ 12: 12mA
+
+
+Note that many of these properties are only valid for certain specific pins
+or groups. See the TZ1090 TRM for complete details regarding which groups
+support which functionality. The Linux pinctrl driver may also be a useful
+reference.
+
+Valid values for pin and group names are:
+
+ gpio pins:
+
+ These all support bias-high-impediance, bias-pull-up, bias-pull-down, and
+ bias-bus-hold (which can also be provided to any of the groups below to set
+ it for all pins in that group).
+
+ They also all support the some form of muxing. Any pins which are contained
+ in one of the mux groups (see below) can be muxed only to the functions
+ supported by the mux group. All other pins can be muxed to the "perip"
+ function which enables them with their intended peripheral.
+
+ Different pins in the same mux group cannot be muxed to different functions,
+ however it is possible to mux only a subset of the pins in a mux group to a
+ particular function and leave the remaining pins unmuxed. This is useful if
+ the board connects certain pins in a group to other devices to be controlled
+ by GPIO, and you don't want the usual peripheral to have any control of the
+ pin.
+
+ ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7,
+ i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out,
+ i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on,
+ scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd,
+ sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
+ spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0,
+ spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0,
+ tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7,
+ tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5,
+ tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0,
+ tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7,
+ tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts,
+ uart0_rxd, uart0_txd, uart1_rxd, uart1_txd.
+
+ bias-high-impediance: supported.
+ bias-pull-up: supported.
+ bias-pull-down: supported.
+ bias-bus-hold: supported.
+ function: perip or those supported by pin's mux group.
+
+ other pins:
+
+ These other pins are part of various pin groups below, but can't be
+ controlled as GPIOs. They do however support bias-high-impediance,
+ bias-pull-up, bias-pull-down, and bias-bus-hold (which can also be provided
+ to any of the groups below to set it for all pins in that group).
+
+ clk_out0, clk_out1, tck, tdi, tdo, tms, trst.
+
+ bias-high-impediance: supported.
+ bias-pull-up: supported.
+ bias-pull-down: supported.
+ bias-bus-hold: supported.
+
+ mux groups:
+
+ These all support function, and some support drive configs.
+
+ afe
+ pins: tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0,
+ ant_sel1, gain0, gain1, gain2, gain3, gain4,
+ gain5, gain6, gain7.
+ function: afe, ts_out_0.
+ input-schmitt-enable: supported.
+ input-schmitt-disable: supported.
+ drive-strength: supported.
+ pdm_d
+ pins: pdm_d.
+ function: pdm_dac, usb_vbus.
+ sdh
+ pins: sdh_cd, sdh_wp, sdh_clk_in.
+ function: sdh, sdio.
+ sdio
+ pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2,
+ sdio_d3.
+ function: sdio, sdh.
+ spi1_cs2
+ pins: spi1_cs2.
+ function: spi1_cs2, usb_vbus.
+ tft
+ pins: tft_red0, tft_red1, tft_red2, tft_red3,
+ tft_red4, tft_red5, tft_red6, tft_red7,
+ tft_green0, tft_green1, tft_green2, tft_green3,
+ tft_green4, tft_green5, tft_green6, tft_green7,
+ tft_blue0, tft_blue1, tft_blue2, tft_blue3,
+ tft_blue4, tft_blue5, tft_blue6, tft_blue7,
+ tft_vdden_gd, tft_panelclk, tft_blank_ls,
+ tft_vsync_ns, tft_hsync_nr, tft_vd12acb,
+ tft_pwrsave.
+ function: tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1,
+ lcd_trace, phy_ringosc.
+ input-schmitt-enable: supported.
+ input-schmitt-disable: supported.
+ drive-strength: supported.
+
+ drive groups:
+
+ These all support input-schmitt-enable, input-schmitt-disable,
+ and drive-strength.
+
+ jtag
+ pins: tck, trst, tdi, tdo, tms.
+ scb1
+ pins: scb1_sdat, scb1_sclk.
+ scb2
+ pins: scb2_sdat, scb2_sclk.
+ spi0
+ pins: spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din.
+ spi1
+ pins: spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din.
+ uart
+ pins: uart0_txd, uart0_rxd, uart0_rts, uart0_cts,
+ uart1_txd, uart1_rxd.
+ drive_i2s
+ pins: clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
+ i2s_lrclk_out, i2s_bclk_out, i2s_mclk.
+ drive_pdm
+ pins: clk_out0, pdm_b, pdm_a.
+ drive_scb0
+ pins: scb0_sclk, scb0_sdat, pdm_d, pdm_c.
+ drive_sdio
+ pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
+ sdh_wp, sdh_cd, sdh_clk_in.
+
+ convenience groups:
+
+ These are just convenient groupings of pins and don't support any drive
+ configs.
+
+ uart0
+ pins: uart0_cts, uart0_rts, uart0_rxd, uart0_txd.
+ uart1
+ pins: uart1_rxd, uart1_txd.
+ scb0
+ pins: scb0_sclk, scb0_sdat.
+ i2s
+ pins: i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
+ i2s_lrclk_out, i2s_mclk.
+
+Example:
+
+ pinctrl: pinctrl@02005800 {
+ #gpio-range-cells = <3>;
+ compatible = "img,tz1090-pinctrl";
+ reg = <0x02005800 0xe4>;
+ };
+
+Example board file extract:
+
+ &pinctrl {
+ uart0_default: uart0 {
+ uart0_cfg {
+ tz1090,pins = "uart0_rxd",
+ "uart0_txd";
+ tz1090,function = "perip";
+ };
+ };
+ tft_default: tft {
+ tft_cfg {
+ tz1090,pins = "tft";
+ tz1090,function = "tft";
+ };
+ };
+ };
+
+ uart@02004b00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_default>;
+ };