diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/pci')
21 files changed, 1585 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt b/kernel/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt new file mode 100644 index 000000000..35a465362 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt @@ -0,0 +1,40 @@ +* Freescale 83xx and 512x PCI bridges + +Freescale 83xx and 512x SOCs include the same pci bridge core. + +83xx/512x specific notes: +- reg: should contain two address length tuples + The first is for the internal pci bridge registers + The second is for the pci config space access registers + +Example (MPC8313ERDB) + pci0: pci@e0008500 { + cell-index = <1>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0E -mini PCI */ + 0x7000 0x0 0x0 0x1 &ipic 18 0x8 + 0x7000 0x0 0x0 0x2 &ipic 18 0x8 + 0x7000 0x0 0x0 0x3 &ipic 18 0x8 + 0x7000 0x0 0x0 0x4 &ipic 18 0x8 + + /* IDSEL 0x0F - PCI slot */ + 0x7800 0x0 0x0 0x1 &ipic 17 0x8 + 0x7800 0x0 0x0 0x2 &ipic 18 0x8 + 0x7800 0x0 0x0 0x3 &ipic 17 0x8 + 0x7800 0x0 0x0 0x4 &ipic 18 0x8>; + interrupt-parent = <&ipic>; + interrupts = <66 0x8>; + bus-range = <0x0 0x0>; + ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 + 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 + 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + clock-frequency = <66666666>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ + compatible = "fsl,mpc8349-pci"; + device_type = "pci"; + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/kernel/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt new file mode 100644 index 000000000..f7ce50e38 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt @@ -0,0 +1,63 @@ +* Broadcom iProc PCIe controller with the platform bus interface + +Required properties: +- compatible: Must be "brcm,iproc-pcie" +- reg: base address and length of the PCIe controller I/O register space +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map, standard PCI properties to define the + mapping of the PCIe interface to interrupt numbers +- linux,pci-domain: PCI domain ID. Should be unique for each host controller +- bus-range: PCI bus numbers covered +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions + +Optional properties: +- phys: phandle of the PCIe PHY device +- phy-names: must be "pcie-phy" + +Example: + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18012000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; + + linux,pci-domain = <0>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x28000000 0 0x00010000 + 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + + phys = <&phy 0 5>; + phy-names = "pcie-phy"; + }; + + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18013000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; + + linux,pci-domain = <1>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x48000000 0 0x00010000 + 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + + phys = <&phy 1 6>; + phy-names = "pcie-phy"; + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/designware-pcie.txt b/kernel/Documentation/devicetree/bindings/pci/designware-pcie.txt new file mode 100644 index 000000000..9f4faa8e8 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -0,0 +1,28 @@ +* Synopsys Designware PCIe interface + +Required properties: +- compatible: should contain "snps,dw-pcie" to identify the core. +- reg: Should contain the configuration address space. +- reg-names: Must be "config" for the PCIe configuration space. + (The old way of getting the configuration address space from "ranges" + is deprecated and should be avoided.) +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- num-lanes: number of lanes to use +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "pcie" + - "pcie_bus" + +Optional properties: +- reset-gpio: gpio pin number of power good signal +- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to + specify this property, to keep backwards compatibility a range of 0x00-0xff + is assumed if not present) diff --git a/kernel/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/kernel/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt new file mode 100644 index 000000000..6fbba53a3 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -0,0 +1,40 @@ +* Freescale i.MX6 PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "fsl,imx6q-pcie" +- reg: base addresse and length of the pcie controller +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + - "msi": The interrupt that is asserted when an MSI is received +- clock-names: Must include the following additional entries: + - "pcie_phy" + +Example: + + pcie@0x01000000 { + compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; + reg = <0x01ffc000 0x04000>, + <0x01f00000 0x80000>; + reg-names = "dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 + 0x81000000 0 0 0x01f80000 0 0x00010000 + 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; + num-lanes = <1>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 144>, <&clks 206>, <&clks 189>; + clock-names = "pcie", "pcie_bus", "pcie_phy"; + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/fsl,pci.txt b/kernel/Documentation/devicetree/bindings/pci/fsl,pci.txt new file mode 100644 index 000000000..d8ac4a768 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/fsl,pci.txt @@ -0,0 +1,27 @@ +* Bus Enumeration by Freescale PCI-X Agent + +Typically any Freescale PCI-X bridge hardware strapped into Agent mode +is prevented from enumerating the bus. The PrPMC form-factor requires +all mezzanines to be PCI-X Agents, but one per system may still +enumerate the bus. + +The property defined below will allow a PCI-X bridge to be used for bus +enumeration despite being strapped into Agent mode. + +Required properties: +- fsl,pci-agent-force-enum : There is no value associated with this + property. The property itself is treated as a boolean. + +Example: + + /* PCI-X bridge known to be PrPMC Monarch */ + pci0: pci@ef008000 { + fsl,pci-agent-force-enum; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci"; + device_type = "pci"; + ... + ... + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/host-generic-pci.txt b/kernel/Documentation/devicetree/bindings/pci/host-generic-pci.txt new file mode 100644 index 000000000..cf3e205e0 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/host-generic-pci.txt @@ -0,0 +1,100 @@ +* Generic PCI host controller + +Firmware-initialised PCI host controllers and PCI emulations, such as the +virtio-pci implementations found in kvmtool and other para-virtualised +systems, do not require driver support for complexities such as regulator +and clock management. In fact, the controller may not even require the +configuration of a control interface by the operating system, instead +presenting a set of fixed windows describing a subset of IO, Memory and +Configuration Spaces. + +Such a controller can be described purely in terms of the standardized device +tree bindings communicated in pci.txt: + + +Properties of the host controller node: + +- compatible : Must be "pci-host-cam-generic" or "pci-host-ecam-generic" + depending on the layout of configuration space (CAM vs + ECAM respectively). + +- device_type : Must be "pci". + +- ranges : As described in IEEE Std 1275-1994, but must provide + at least a definition of non-prefetchable memory. One + or both of prefetchable Memory and IO Space may also + be provided. + +- bus-range : Optional property (also described in IEEE Std 1275-1994) + to indicate the range of bus numbers for this controller. + If absent, defaults to <0 255> (i.e. all buses). + +- #address-cells : Must be 3. + +- #size-cells : Must be 2. + +- reg : The Configuration Space base address and size, as accessed + from the parent bus. + + +Properties of the /chosen node: + +- linux,pci-probe-only + : Optional property which takes a single-cell argument. + If '0', then Linux will assign devices in its usual manner, + otherwise it will not try to assign devices and instead use + them as they are configured already. + +Configuration Space is assumed to be memory-mapped (as opposed to being +accessed via an ioport) and laid out with a direct correspondence to the +geography of a PCI bus address by concatenating the various components to +form an offset. + +For CAM, this 24-bit offset is: + + cfg_offset(bus, device, function, register) = + bus << 16 | device << 11 | function << 8 | register + +Whilst ECAM extends this by 4 bits to accommodate 4k of function space: + + cfg_offset(bus, device, function, register) = + bus << 20 | device << 15 | function << 12 | register + +Interrupt mapping is exactly as described in `Open Firmware Recommended +Practice: Interrupt Mapping' and requires the following properties: + +- #interrupt-cells : Must be 1 + +- interrupt-map : <see aforementioned specification> + +- interrupt-map-mask : <see aforementioned specification> + + +Example: + +pci { + compatible = "pci-host-cam-generic" + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0x1>; + + // CPU_PHYSICAL(2) SIZE(2) + reg = <0x0 0x40000000 0x0 0x1000000>; + + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x01000000 0x0 0x01000000 0x0 0x01000000 0x0 0x00010000>, + <0x02000000 0x0 0x41000000 0x0 0x41000000 0x0 0x3f000000>; + + + #interrupt-cells = <0x1>; + + // PCI_DEVICE(3) INT#(1) CONTROLLER(PHANDLE) CONTROLLER_DATA(3) + interrupt-map = < 0x0 0x0 0x0 0x1 &gic 0x0 0x4 0x1 + 0x800 0x0 0x0 0x1 &gic 0x0 0x5 0x1 + 0x1000 0x0 0x0 0x1 &gic 0x0 0x6 0x1 + 0x1800 0x0 0x0 0x1 &gic 0x0 0x7 0x1>; + + // PCI_DEVICE(3) INT#(1) + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; +} diff --git a/kernel/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/kernel/Documentation/devicetree/bindings/pci/layerscape-pci.txt new file mode 100644 index 000000000..6286f049b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -0,0 +1,42 @@ +Freescale Layerscape PCIe controller + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: should contain the platform identifier such as "fsl,ls1021a-pcie" +- reg: base addresses and lengths of the PCIe controller +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + "intr": The interrupt that is asserted for controller interrupts +- fsl,pcie-scfg: Must include two entries. + The first entry must be a link to the SCFG device node + The second entry must be '0' or '1' based on physical PCIe controller index. + This is used to get SCFG PEXN registers + +Example: + + pcie@3400000 { + compatible = "fsl,ls1021a-pcie", "snps,dw-pcie"; + reg = <0x00 0x03400000 0x0 0x00010000 /* controller registers */ + 0x40 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ + interrupt-names = "intr"; + fsl,pcie-scfg = <&scfg 0>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0xc2000000 0x0 0x20000000 0x40 0x20000000 0x0 0x20000000 /* prefetchable memory */ + 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 2 &gic GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 3 &gic GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 4 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/kernel/Documentation/devicetree/bindings/pci/mvebu-pci.txt new file mode 100644 index 000000000..08c716b2c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/mvebu-pci.txt @@ -0,0 +1,304 @@ +* Marvell EBU PCIe interfaces + +Mandatory properties: + +- compatible: one of the following values: + marvell,armada-370-pcie + marvell,armada-xp-pcie + marvell,dove-pcie + marvell,kirkwood-pcie +- #address-cells, set to <3> +- #size-cells, set to <2> +- #interrupt-cells, set to <1> +- bus-range: PCI bus numbers covered +- device_type, set to "pci" +- ranges: ranges describing the MMIO registers to control the PCIe + interfaces, and ranges describing the MBus windows needed to access + the memory and I/O regions of each PCIe interface. +- msi-parent: Link to the hardware entity that serves as the Message + Signaled Interrupt controller for this PCI controller. + +The ranges describing the MMIO registers have the following layout: + + 0x82000000 0 r MBUS_ID(0xf0, 0x01) r 0 s + +where: + + * r is a 32-bits value that gives the offset of the MMIO + registers of this PCIe interface, from the base of the internal + registers. + + * s is a 32-bits value that give the size of this MMIO + registers area. This range entry translates the '0x82000000 0 r' PCI + address into the 'MBUS_ID(0xf0, 0x01) r' CPU address, which is part + of the internal register window (as identified by MBUS_ID(0xf0, + 0x01)). + +The ranges describing the MBus windows have the following layout: + + 0x8t000000 s 0 MBUS_ID(w, a) 0 1 0 + +where: + + * t is the type of the MBus window (as defined by the standard PCI DT + bindings), 1 for I/O and 2 for memory. + + * s is the PCI slot that corresponds to this PCIe interface + + * w is the 'target ID' value for the MBus window + + * a the 'attribute' value for the MBus window. + +Since the location and size of the different MBus windows is not fixed in +hardware, and only determined in runtime, those ranges cover the full first +4 GB of the physical address space, and do not translate into a valid CPU +address. + +In addition, the device tree node must have sub-nodes describing each +PCIe interface, having the following mandatory properties: + +- reg: used only for interrupt mapping, so only the first four bytes + are used to refer to the correct bus number and device number. +- assigned-addresses: reference to the MMIO registers used to control + this PCIe interface. +- clocks: the clock associated to this PCIe interface +- marvell,pcie-port: the physical PCIe port number +- status: either "disabled" or "okay" +- device_type, set to "pci" +- #address-cells, set to <3> +- #size-cells, set to <2> +- #interrupt-cells, set to <1> +- ranges, translating the MBus windows ranges of the parent node into + standard PCI addresses. +- interrupt-map-mask and interrupt-map, standard PCI properties to + define the mapping of the PCIe interface to interrupt numbers. + +and the following optional properties: +- marvell,pcie-lane: the physical PCIe lane number, for ports having + multiple lanes. If this property is not found, we assume that the + value is 0. +- reset-gpios: optional gpio to PERST# +- reset-delay-us: delay in us to wait after reset de-assertion + +Example: + +pcie-controller { + compatible = "marvell,armada-xp-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + bus-range = <0x00 0xff>; + msi-parent = <&mpic>; + + ranges = + <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ + 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */ + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */ + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ + 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ + 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ + 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */ + 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */ + 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */ + 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */ + 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ + 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ + 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ + + 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ + 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ + 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */ + 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */ + 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */ + 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */ + 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */ + 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */ + + 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ + 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */ + + 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */ + 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>; + + pcie@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 58>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + /* low-active PERST# reset on GPIO 25 */ + reset-gpios = <&gpio0 25 1>; + /* wait 20ms for device settle after reset deassertion */ + reset-delay-us = <20000>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + pcie@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 59>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + pcie@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x48000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 60>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + + pcie@4,0 { + device_type = "pci"; + assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 + 0x81000000 0 0 0x81000000 0x4 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 61>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + pcie@5,0 { + device_type = "pci"; + assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; + reg = <0x2800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 + 0x81000000 0 0 0x81000000 0x5 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 62>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 9>; + status = "disabled"; + }; + + pcie@6,0 { + device_type = "pci"; + assigned-addresses = <0x82003000 0 0x84000 0 0x2000>; + reg = <0x3000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0 + 0x81000000 0 0 0x81000000 0x6 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 63>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 10>; + status = "disabled"; + }; + + pcie@7,0 { + device_type = "pci"; + assigned-addresses = <0x82003800 0 0x88000 0 0x2000>; + reg = <0x3800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0 + 0x81000000 0 0 0x81000000 0x7 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 64>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 11>; + status = "disabled"; + }; + + pcie@8,0 { + device_type = "pci"; + assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>; + reg = <0x4000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0 + 0x81000000 0 0 0x81000000 0x8 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 65>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 12>; + status = "disabled"; + }; + + pcie@9,0 { + device_type = "pci"; + assigned-addresses = <0x82004800 0 0x42000 0 0x2000>; + reg = <0x4800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 + 0x81000000 0 0 0x81000000 0x9 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 99>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 26>; + status = "disabled"; + }; + + pcie@10,0 { + device_type = "pci"; + assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; + reg = <0x5000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0 + 0x81000000 0 0 0x81000000 0xa 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 103>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 27>; + status = "disabled"; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/kernel/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt new file mode 100644 index 000000000..75321ae23 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -0,0 +1,224 @@ +NVIDIA Tegra PCIe controller + +Required properties: +- compatible: For Tegra20, must contain "nvidia,tegra20-pcie". For Tegra30, + "nvidia,tegra30-pcie". For Tegra124, must contain "nvidia,tegra124-pcie". + Otherwise, must contain "nvidia,<chip>-pcie", plus one of the above, where + <chip> is tegra132 or tegra210. +- device_type: Must be "pci" +- reg: A list of physical base address and length for each set of controller + registers. Must contain an entry for each entry in the reg-names property. +- reg-names: Must include the following entries: + "pads": PADS registers + "afi": AFI registers + "cs": configuration space region +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + "intr": The Tegra interrupt that is asserted for controller interrupts + "msi": The Tegra interrupt that is asserted when an MSI is received +- bus-range: Range of bus numbers associated with this controller +- #address-cells: Address representation for root ports (must be 3) + - cell 0 specifies the bus and device numbers of the root port: + [23:16]: bus number + [15:11]: device number + - cell 1 denotes the upper 32 address bits and should be 0 + - cell 2 contains the lower 32 address bits and is used to translate to the + CPU address space +- #size-cells: Size representation for root ports (must be 2) +- ranges: Describes the translation of addresses for root ports and standard + PCI regions. The entries must be 6 cells each, where the first three cells + correspond to the address as described for the #address-cells property + above, the fourth cell is the physical CPU address to translate to and the + fifth and six cells are as described for the #size-cells property above. + - The first two entries are expected to translate the addresses for the root + port registers, which are referenced by the assigned-addresses property of + the root port nodes (see below). + - The remaining entries setup the mapping for the standard I/O, memory and + prefetchable PCI regions. The first cell determines the type of region + that is setup: + - 0x81000000: I/O memory region + - 0x82000000: non-prefetchable memory region + - 0xc2000000: prefetchable memory region + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - pex + - afi + - pll_e + - cml (not required for Tegra20) +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pex + - afi + - pcie_x + +Required properties on Tegra124 and later: +- phys: Must contain an entry for each entry in phy-names. +- phy-names: Must include the following entries: + - pcie + +Power supplies for Tegra20: +- avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. +- vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. +- avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. +- avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must + supply 1.05 V. +- vddio-pex-clk-supply: Power supply for PCIe clock. Must supply 3.3 V. + +Power supplies for Tegra30: +- Required: + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must + supply 1.05 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. +- Optional: + - If lanes 0 to 3 are used: + - avdd-pexa-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - vdd-pexa-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - If lanes 4 or 5 are used: + - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + +Power supplies for Tegra124: +- Required: + - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 2.8-3.3 V. + - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + +Root ports are defined as subnodes of the PCIe controller node. + +Required properties: +- device_type: Must be "pci" +- assigned-addresses: Address and size of the port configuration registers +- reg: PCI bus address of the root port +- #address-cells: Must be 3 +- #size-cells: Must be 2 +- ranges: Sub-ranges distributed from the PCIe controller node. An empty + property is sufficient. +- nvidia,num-lanes: Number of lanes to use for this port. Valid combinations + are: + - Root port 0 uses 4 lanes, root port 1 is unused. + - Both root ports use 2 lanes. + +Example: + +SoC DTSI: + + pcie-controller { + compatible = "nvidia,tegra20-pcie"; + device_type = "pci"; + reg = <0x80003000 0x00000800 /* PADS registers */ + 0x80003800 0x00000200 /* AFI registers */ + 0x90000000 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <0 98 0x04 /* controller interrupt */ + 0 99 0x04>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x80000000 0x80000000 0 0x00001000 /* port 0 registers */ + 0x82000000 0 0x80001000 0x80001000 0 0x00001000 /* port 1 registers */ + 0x81000000 0 0 0x82000000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0xa0000000 0xa0000000 0 0x10000000 /* non-prefetchable memory */ + 0xc2000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */ + + clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 118>; + clock-names = "pex", "afi", "pll_e"; + resets = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x80001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + + ranges; + + nvidia,num-lanes = <2>; + }; + }; + + +Board DTS: + + pcie-controller { + status = "okay"; + + vdd-supply = <&pci_vdd_reg>; + pex-clk-supply = <&pci_clk_reg>; + + /* root port 00:01.0 */ + pci@1,0 { + status = "okay"; + + /* bridge 01:00.0 (optional) */ + pci@0,0 { + reg = <0x010000 0 0 0 0>; + + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + + /* endpoint 02:00.0 */ + pci@0,0 { + reg = <0x020000 0 0 0 0>; + }; + }; + }; + }; + +Note that devices on the PCI bus are dynamically discovered using PCI's bus +enumeration and therefore don't need corresponding device nodes in DT. However +if a device on the PCI bus provides a non-probeable bus such as I2C or SPI, +device nodes need to be added in order to allow the bus' children to be +instantiated at the proper location in the operating system's device tree (as +illustrated by the optional nodes in the example above). diff --git a/kernel/Documentation/devicetree/bindings/pci/pci-keystone.txt b/kernel/Documentation/devicetree/bindings/pci/pci-keystone.txt new file mode 100644 index 000000000..54eae2938 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -0,0 +1,63 @@ +TI Keystone PCIe interface + +Keystone PCI host Controller is based on Designware PCI h/w version 3.65. +It shares common functions with PCIe Designware core driver and inherit +common properties defined in +Documentation/devicetree/bindings/pci/designware-pci.txt + +Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt +for the details of Designware DT bindings. Additional properties are +described here as well as properties that are not applicable. + +Required Properties:- + +compatibility: "ti,keystone-pcie" +reg: index 1 is the base address and length of DW application registers. + index 2 is the base address and length of PCI device ID register. + +pcie_msi_intc : Interrupt controller device node for MSI IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI MSI interrupt lines + + Example: + pcie_msi_intc: msi-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>; + }; + +pcie_intc: Interrupt controller device node for Legacy IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines + + Example: + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 28 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>; + }; + +Optional properties:- + phys: phandle to Generic Keystone SerDes phy for PCI + phy-names: name of the Generic Keystine SerDes phy for PCI + - If boot loader already does PCI link establishment, then phys and + phy-names shouldn't be present. + +Designware DT Properties not applicable for Keystone PCI + +1. pcie_bus clock-names not used. Instead, a phandle to phys is used. + diff --git a/kernel/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/kernel/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt new file mode 100644 index 000000000..d8ef5bf50 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -0,0 +1,66 @@ +Renesas AHB to PCI bridge +------------------------- + +This is the bridge used internally to connect the USB controllers to the +AHB. There is one bridge instance per USB port connected to the internal +OHCI and EHCI controllers. + +Required properties: +- compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; + "renesas,pci-r8a7791" for the R8A7791 SoC. +- reg: A list of physical regions to access the device: the first is + the operational registers for the OHCI/EHCI controllers and the + second is for the bridge configuration and control registers. +- interrupts: interrupt for the device. +- clocks: The reference to the device clock. +- bus-range: The PCI bus number range; as this is a single bus, the range + should be specified as the same value twice. +- #address-cells: must be 3. +- #size-cells: must be 2. +- #interrupt-cells: must be 1. +- interrupt-map: standard property used to define the mapping of the PCI + interrupts to the GIC interrupts. +- interrupt-map-mask: standard property that helps to define the interrupt + mapping. + +Example SoC configuration: + + pci0: pci@ee090000 { + compatible = "renesas,pci-r8a7790"; + clocks = <&mstp7_clks R8A7790_CLK_EHCI>; + reg = <0x0 0xee090000 0x0 0xc00>, + <0x0 0xee080000 0x0 0x1100>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; + + pci@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + + pci@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + }; + +Example board setup: + +&pci0 { + status = "okay"; + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; +}; diff --git a/kernel/Documentation/devicetree/bindings/pci/pci.txt b/kernel/Documentation/devicetree/bindings/pci/pci.txt new file mode 100644 index 000000000..f8fbe9af7 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/pci.txt @@ -0,0 +1,20 @@ +PCI bus bridges have standardized Device Tree bindings: + +PCI Bus Binding to: IEEE Std 1275-1994 +http://www.openfirmware.org/ofwg/bindings/pci/pci2_1.pdf + +And for the interrupt mapping part: + +Open Firmware Recommended Practice: Interrupt Mapping +http://www.openfirmware.org/1275/practice/imap/imap0_9d.pdf + +Additionally to the properties specified in the above standards a host bridge +driver implementation may support the following properties: + +- linux,pci-domain: + If present this property assigns a fixed PCI domain number to a host bridge, + otherwise an unstable (across boots) unique number will be assigned. + It is required to either not set this property at all or set it for all + host bridges in the system, otherwise potentially conflicting domain numbers + may be assigned to root buses behind different host bridges. The domain + number for each host bridge in the system must be unique. diff --git a/kernel/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt b/kernel/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt new file mode 100644 index 000000000..8e0a1eb0a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt @@ -0,0 +1,190 @@ +* Mediatek/Ralink RT3883 PCI controller + +1) Main node + + Required properties: + + - compatible: must be "ralink,rt3883-pci" + + - reg: specifies the physical base address of the controller and + the length of the memory mapped region. + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 1. + + - #size-cells: specifies the number of cells used to represent the size + of an address. The value must be 1. + + - ranges: specifies the translation between child address space and parent + address space + + Optional properties: + + - status: indicates the operational status of the device. + Value must be either "disabled" or "okay". + +2) Child nodes + + The main node must have two child nodes which describes the built-in + interrupt controller and the PCI host bridge. + + a) Interrupt controller: + + Required properties: + + - interrupt-controller: identifies the node as an interrupt controller + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. As such, 'interrupt-map' nodes do not + have to specify a parent unit address. + + - #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + + - interrupts: specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. + + b) PCI host bridge: + + Required properties: + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. + + - #size-cells: specifies the number of cells used to represent the size + of an address. The value must be 2. + + - #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + + - device_type: must be "pci" + + - bus-range: PCI bus numbers covered + + - ranges: specifies the ranges for the PCI memory and I/O regions + + - interrupt-map-mask, + - interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. + + The PCI host bridge node migh have additional sub-nodes representing + the onboard PCI devices/PCI slots. Each such sub-node must have the + following mandatory properties: + + - reg: used only for interrupt mapping, so only the first four bytes + are used to refer to the correct bus number and device number. + + - device_type: must be "pci" + + If a given sub-node represents a PCI bridge it must have following + mandatory properties as well: + + - #address-cells: must be set to <3> + + - #size-cells: must set to <2> + + - #interrupt-cells: must be set to <1> + + - interrupt-map-mask, + - interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. + + Besides the required properties the sub-nodes may have these optional + properties: + + - status: indicates the operational status of the sub-node. + Value must be either "disabled" or "okay". + +3) Example: + + a) SoC specific dtsi file: + + pci@10140000 { + compatible = "ralink,rt3883-pci"; + reg = <0x10140000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; /* direct mapping */ + + status = "disabled"; + + pciintc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + + interrupt-parent = <&cpuintc>; + interrupts = <4>; + }; + + host-bridge { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + device_type = "pci"; + + bus-range = <0 255>; + ranges = < + 0x02000000 0 0x00000000 0x20000000 0 0x10000000 /* pci memory */ + 0x01000000 0 0x00000000 0x10160000 0 0x00010000 /* io space */ + >; + + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 17 */ + 0x8800 0 0 1 &pciintc 18 + 0x8800 0 0 2 &pciintc 18 + 0x8800 0 0 3 &pciintc 18 + 0x8800 0 0 4 &pciintc 18 + /* IDSEL 18 */ + 0x9000 0 0 1 &pciintc 19 + 0x9000 0 0 2 &pciintc 19 + 0x9000 0 0 3 &pciintc 19 + 0x9000 0 0 4 &pciintc 19 + >; + + pci-bridge@1 { + reg = <0x0800 0 0 0 0>; + device_type = "pci"; + #interrupt-cells = <1>; + #address-cells = <3>; + #size-cells = <2>; + + interrupt-map-mask = <0x0 0 0 0>; + interrupt-map = <0x0 0 0 0 &pciintc 20>; + + status = "disabled"; + }; + + pci-slot@17 { + reg = <0x8800 0 0 0 0>; + device_type = "pci"; + + status = "disabled"; + }; + + pci-slot@18 { + reg = <0x9000 0 0 0 0>; + device_type = "pci"; + + status = "disabled"; + }; + }; + }; + + b) Board specific dts file: + + pci@10140000 { + status = "okay"; + + host-bridge { + pci-bridge@1 { + status = "okay"; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/rcar-pci.txt b/kernel/Documentation/devicetree/bindings/pci/rcar-pci.txt new file mode 100644 index 000000000..29d3b989d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -0,0 +1,47 @@ +* Renesas RCar PCIe interface + +Required properties: +- compatible: should contain one of the following + "renesas,pcie-r8a7779", "renesas,pcie-r8a7790", "renesas,pcie-r8a7791" +- reg: base address and length of the pcie controller registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- bus-range: PCI bus numbers covered +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- interrupts: two interrupt sources for MSI interrupts, followed by interrupt + source for hardware related interrupts (e.g. link speed change). +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: clock specifiers for the PCIe controller + and PCIe bus clocks. +- clock-names: from common clock binding: should be "pcie" and "pcie_bus". + +Example: + +SoC specific DT Entry: + + pcie: pcie@fe000000 { + compatible = "renesas,pcie-r8a7791"; + reg = <0 0xfe000000 0 0x80000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + device_type = "pci"; + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000 + 0x42000000 2 0x00000000 2 0x00000000 0 0x40000000>; + interrupts = <0 116 4>, <0 117 4>, <0 118 4>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 116 4>; + clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>; + clock-names = "pcie", "pcie_bus"; + status = "disabled"; + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/kernel/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt new file mode 100644 index 000000000..4f9d23d2e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt @@ -0,0 +1,65 @@ +* Samsung Exynos 5440 PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "samsung,exynos5440-pcie" +- reg: base addresses and lengths of the pcie controller, + the phy controller, additional register for the phy controller. +- interrupts: A list of interrupt outputs for level interrupt, + pulse interrupt, special interrupt. + +Example: + +SoC specific DT Entry: + + pcie@290000 { + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; + reg = <0x290000 0x1000 + 0x270000 0x1000 + 0x271000 0x40>; + interrupts = <0 20 0>, <0 21 0>, <0 22 0>; + clocks = <&clock 28>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ + 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; + }; + + pcie@2a0000 { + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; + reg = <0x2a0000 0x1000 + 0x272000 0x1000 + 0x271040 0x40>; + interrupts = <0 23 0>, <0 24 0>, <0 25 0>; + clocks = <&clock 29>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ + 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; + }; + +Board specific DT Entry: + + pcie@290000 { + reset-gpio = <&pin_ctrl 5 0>; + }; + + pcie@2a0000 { + reset-gpio = <&pin_ctrl 22 0>; + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt b/kernel/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt new file mode 100644 index 000000000..49ea76da7 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt @@ -0,0 +1,14 @@ +SPEAr13XX PCIe DT detail: +================================ + +SPEAr13XX uses synopsis designware PCIe controller and ST MiPHY as phy +controller. + +Required properties: +- compatible : should be "st,spear1340-pcie", "snps,dw-pcie". +- phys : phandle to phy node associated with pcie controller +- phy-names : must be "pcie-phy" +- All other definitions as per generic PCI bindings + + Optional properties: +- st,pcie-is-gen1 indicates that forced gen1 initialization is needed. diff --git a/kernel/Documentation/devicetree/bindings/pci/ti-pci.txt b/kernel/Documentation/devicetree/bindings/pci/ti-pci.txt new file mode 100644 index 000000000..3d217911b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -0,0 +1,59 @@ +TI PCI Controllers + +PCIe Designware Controller + - compatible: Should be "ti,dra7-pcie"" + - reg : Two register ranges as listed in the reg-names property + - reg-names : The first entry must be "ti-conf" for the TI specific registers + The second entry must be "rc-dbics" for the designware pcie + registers + The third entry must be "config" for the PCIe configuration space + - phys : list of PHY specifiers (used by generic PHY framework) + - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of PHYs as specified in *phys* property. + - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", + where <X> is the instance number of the pcie from the HW spec. + - interrupts : Two interrupt entries must be specified. The first one is for + main interrupt line and the second for MSI interrupt line. + - #address-cells, + #size-cells, + #interrupt-cells, + device_type, + ranges, + num-lanes, + interrupt-map-mask, + interrupt-map : as specified in ../designware-pcie.txt + +Example: +axi { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0x51000000 0x51000000 0x3000 + 0x0 0x20000000 0x10000000>; + pcie@51000000 { + compatible = "ti,dra7-pcie"; + reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>; + reg-names = "rc_dbics", "ti_conf", "config"; + interrupts = <0 232 0x4>, <0 233 0x4>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x03000 0 0x00010000 + 0x82000000 0 0x20013000 0x13000 0 0xffed000>; + #interrupt-cells = <1>; + num-lanes = <1>; + ti,hwmods = "pcie1"; + phys = <&pcie1_phy>; + phy-names = "pcie-phy0"; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt b/kernel/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt new file mode 100644 index 000000000..30b364e50 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt @@ -0,0 +1,15 @@ +V3 Semiconductor V360 EPC PCI bridge + +This bridge is found in the ARM Integrator/AP (Application Platform) + +Integrator-specific notes: + +- syscon: should contain a link to the syscon device node (since + on the Integrator, some registers in the syscon are required to + operate the V3). + +V360 EPC specific notes: + +- reg: should contain the base address of the V3 adapter. +- interrupts: should contain a reference to the V3 error interrupt + as routed on the system. diff --git a/kernel/Documentation/devicetree/bindings/pci/versatile.txt b/kernel/Documentation/devicetree/bindings/pci/versatile.txt new file mode 100644 index 000000000..ebd1e7d04 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/versatile.txt @@ -0,0 +1,59 @@ +* ARM Versatile Platform Baseboard PCI interface + +PCI host controller found on the ARM Versatile PB board's FPGA. + +Required properties: +- compatible: should contain "arm,versatile-pci" to identify the Versatile PCI + controller. +- reg: base addresses and lengths of the pci controller. There must be 3 + entries: + - Versatile-specific registers + - Self Config space + - Config space +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- bus-range: set to <0 0xff> +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties to define + the mapping of the PCI interface to interrupt numbers. + +Example: + +pci-controller@10001000 { + compatible = "arm,versatile-pci"; + device_type = "pci"; + reg = <0x10001000 0x1000 + 0x41000000 0x10000 + 0x42000000 0x100000>; + bus-range = <0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + ranges = <0x01000000 0 0x00000000 0x43000000 0 0x00010000 /* downstream I/O */ + 0x02000000 0 0x50000000 0x50000000 0 0x10000000 /* non-prefetchable memory */ + 0x42000000 0 0x60000000 0x60000000 0 0x10000000>; /* prefetchable memory */ + + interrupt-map-mask = <0x1800 0 0 7>; + interrupt-map = <0x1800 0 0 1 &sic 28 + 0x1800 0 0 2 &sic 29 + 0x1800 0 0 3 &sic 30 + 0x1800 0 0 4 &sic 27 + + 0x1000 0 0 1 &sic 27 + 0x1000 0 0 2 &sic 28 + 0x1000 0 0 3 &sic 29 + 0x1000 0 0 4 &sic 30 + + 0x0800 0 0 1 &sic 30 + 0x0800 0 0 2 &sic 27 + 0x0800 0 0 3 &sic 28 + 0x0800 0 0 4 &sic 29 + + 0x0000 0 0 1 &sic 29 + 0x0000 0 0 2 &sic 30 + 0x0000 0 0 3 &sic 27 + 0x0000 0 0 4 &sic 28>; +}; diff --git a/kernel/Documentation/devicetree/bindings/pci/xgene-pci.txt b/kernel/Documentation/devicetree/bindings/pci/xgene-pci.txt new file mode 100644 index 000000000..1070b068c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/xgene-pci.txt @@ -0,0 +1,57 @@ +* AppliedMicro X-Gene PCIe interface + +Required properties: +- device_type: set to "pci" +- compatible: should contain "apm,xgene-pcie" to identify the core. +- reg: A list of physical base address and length for each set of controller + registers. Must contain an entry for each entry in the reg-names + property. +- reg-names: Must include the following entries: + "csr": controller configuration registers. + "cfg": pcie configuration space registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- ranges: ranges for the outbound memory, I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: handle to pci clock. + +Optional properties: +- status: Either "ok" or "disabled". +- dma-coherent: Present if dma operations are coherent + +Example: + +SoC specific DT Entry: + + pcie0: pcie@1f2b0000 { + status = "disabled"; + device_type = "pci"; + compatible = "apm,xgene-storm-pcie", "apm,xgene-pcie"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = < 0x00 0x1f2b0000 0x0 0x00010000 /* Controller registers */ + 0xe0 0xd0000000 0x0 0x00040000>; /* PCI config space */ + reg-names = "csr", "cfg"; + ranges = <0x01000000 0x00 0x00000000 0xe0 0x10000000 0x00 0x00010000 /* io */ + 0x02000000 0x00 0x80000000 0xe1 0x80000000 0x00 0x80000000>; /* mem */ + dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000 + 0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1 + 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1 + 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1 + 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>; + dma-coherent; + clocks = <&pcie0clk 0>; + }; + + +Board specific DT Entry: + &pcie0 { + status = "ok"; + }; diff --git a/kernel/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/kernel/Documentation/devicetree/bindings/pci/xilinx-pcie.txt new file mode 100644 index 000000000..3e2c88d97 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -0,0 +1,62 @@ +* Xilinx AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "xlnx,axi-pcie-host-1.00.a" +- reg: Should contain AXI PCIe registers location and length +- device_type: must be "pci" +- interrupts: Should contain AXI PCIe interrupt +- interrupt-map-mask, + interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation + +Optional properties: +- bus-range: PCI bus numbers covered + +Interrupt controller child node ++++++++++++++++++++++++++++++++ +Required properties: +- interrupt-controller: identifies the node as an interrupt controller +- #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + +NOTE: +The core provides a single interrupt for both INTx/MSI messages. So, +created a interrupt controller node to support 'interrupt-map' DT +functionality. The driver will create an IRQ domain for this map, decode +the four INTx interrupts in ISR and route them to this domain. + + +Example: +++++++++ + + pci_express: axi-pcie@50000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = < 0x50000000 0x10000000 >; + device_type = "pci"; + interrupts = < 0 52 4 >; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + } + }; |