summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/devicetree/bindings/mtd
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/mtd')
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/arm-versatile.txt8
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt17
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/atmel-nand.txt111
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/davinci-nand.txt94
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/denali-nand.txt23
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/diskonchip.txt15
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/elm.txt16
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/flctl-nand.txt49
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt35
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt67
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/fsmc-nand.txt54
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt47
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/gpmc-nand.txt137
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/gpmc-nor.txt98
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt46
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/gpmi-nand.txt58
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/hisi504-nand.txt47
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt32
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt50
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt52
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/mtd-physmap.txt89
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/mxc-nand.txt19
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/nand.txt21
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/orion-nand.txt50
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/partition.txt71
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt43
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/spear_smi.txt31
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/st-fsm.txt26
-rw-r--r--kernel/Documentation/devicetree/bindings/mtd/sunxi-nand.txt45
29 files changed, 1451 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/mtd/arm-versatile.txt b/kernel/Documentation/devicetree/bindings/mtd/arm-versatile.txt
new file mode 100644
index 000000000..beace4b89
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/arm-versatile.txt
@@ -0,0 +1,8 @@
+Flash device on ARM Versatile board
+
+Required properties:
+- compatible : must be "arm,versatile-flash";
+- bank-width : width in bytes of flash interface.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
diff --git a/kernel/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt b/kernel/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt
new file mode 100644
index 000000000..1889a4db5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt
@@ -0,0 +1,17 @@
+* Atmel Data Flash
+
+Required properties:
+- compatible : "atmel,<model>", "atmel,<series>", "atmel,dataflash".
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+flash@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <25000000>;
+ reg = <1>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/atmel-nand.txt
new file mode 100644
index 000000000..7d4c8eb77
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -0,0 +1,111 @@
+Atmel NAND flash
+
+Required properties:
+- compatible : should be "atmel,at91rm9200-nand" or "atmel,sama5d4-nand".
+- reg : should specify localbus address and size used for the chip,
+ and hardware ECC controller if available.
+ If the hardware ECC is PMECC, it should contain address and size for
+ PMECC and PMECC Error Location controller.
+ The PMECC lookup table address and size in ROM is optional. If not
+ specified, driver will build it in runtime.
+- atmel,nand-addr-offset : offset for the address latch.
+- atmel,nand-cmd-offset : offset for the command latch.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+ representing partitions.
+
+- gpios : specifies the gpio pins to control the NAND device. detect is an
+ optional gpio and may be set to 0 if not present.
+
+Optional properties:
+- atmel,nand-has-dma : boolean to support dma transfer for nand read/write.
+- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
+ Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
+ "soft_bch".
+- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware.
+ Only supported by at91sam9x5 or later sam9 product.
+- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC
+ Controller. Supported values are: 2, 4, 8, 12, 24.
+- atmel,pmecc-sector-size : sector size for ECC computation. Supported values
+ are: 512, 1024.
+- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM
+ for different sector size. First one is for sector size 512, the next is for
+ sector size 1024. If not specified, driver will build the table in runtime.
+- nand-bus-width : 8 or 16 bus width if not present 8
+- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
+- Nand Flash Controller(NFC) is a slave driver under Atmel nand flash
+ - Required properties:
+ - compatible : "atmel,sama5d3-nfc".
+ - reg : should specify the address and size used for NFC command registers,
+ NFC registers and NFC Sram. NFC Sram address and size can be absent
+ if don't want to use it.
+ - clocks: phandle to the peripheral clock
+ - Optional properties:
+ - atmel,write-by-sram: boolean to enable NFC write by sram.
+
+Examples:
+nand0: nand@40000000,0 {
+ compatible = "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x40000000 0x10000000
+ 0xffffe800 0x200
+ >;
+ atmel,nand-addr-offset = <21>; /* ale */
+ atmel,nand-cmd-offset = <22>; /* cle */
+ nand-on-flash-bbt;
+ nand-ecc-mode = "soft";
+ gpios = <&pioC 13 0 /* rdy */
+ &pioC 14 0 /* nce */
+ 0 /* cd */
+ >;
+ partition@0 {
+ ...
+ };
+};
+
+/* for PMECC supported chips */
+nand0: nand@40000000 {
+ compatible = "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = < 0x40000000 0x10000000 /* bus addr & size */
+ 0xffffe000 0x00000600 /* PMECC addr & size */
+ 0xffffe600 0x00000200 /* PMECC ERRLOC addr & size */
+ 0x00100000 0x00100000 /* ROM addr & size */
+ >;
+ atmel,nand-addr-offset = <21>; /* ale */
+ atmel,nand-cmd-offset = <22>; /* cle */
+ nand-on-flash-bbt;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc; /* enable PMECC */
+ atmel,pmecc-cap = <2>;
+ atmel,pmecc-sector-size = <512>;
+ atmel,pmecc-lookup-table-offset = <0x8000 0x10000>;
+ gpios = <&pioD 5 0 /* rdy */
+ &pioD 4 0 /* nce */
+ 0 /* cd */
+ >;
+ partition@0 {
+ ...
+ };
+};
+
+/* for NFC supported chips */
+nand0: nand@40000000 {
+ compatible = "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ...
+ nfc@70000000 {
+ compatible = "atmel,sama5d3-nfc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&hsmc_clk>
+ reg = <
+ 0x70000000 0x10000000 /* NFC Command Registers */
+ 0xffffc000 0x00000070 /* NFC HSMC regs */
+ 0x00200000 0x00100000 /* NFC SRAM banks */
+ >;
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/davinci-nand.txt
new file mode 100644
index 000000000..cfb18abe6
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/davinci-nand.txt
@@ -0,0 +1,94 @@
+Device tree bindings for Texas instruments Davinci/Keystone NAND controller
+
+This file provides information, what the device node for the davinci/keystone
+NAND interface contains.
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
+Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
+
+Required properties:
+
+- compatible: "ti,davinci-nand"
+ "ti,keystone-nand"
+
+- reg: Contains 2 offset/length values:
+ - offset and length for the access window.
+ - offset and length for accessing the AEMIF
+ control registers.
+
+- ti,davinci-chipselect: number of chipselect. Indicates on the
+ davinci_nand driver which chipselect is used
+ for accessing the nand.
+ Can be in the range [0-3].
+
+Recommended properties :
+
+- ti,davinci-mask-ale: mask for ALE. Needed for executing address
+ phase. These offset will be added to the base
+ address for the chip select space the NAND Flash
+ device is connected to.
+ If not set equal to 0x08.
+
+- ti,davinci-mask-cle: mask for CLE. Needed for executing command
+ phase. These offset will be added to the base
+ address for the chip select space the NAND Flash
+ device is connected to.
+ If not set equal to 0x10.
+
+- ti,davinci-mask-chipsel: mask for chipselect address. Needed to mask
+ addresses for given chipselect.
+
+- nand-ecc-mode: operation mode of the NAND ecc mode. ECC mode
+ valid values for davinci driver:
+ - "none"
+ - "soft"
+ - "hw"
+
+- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
+
+- nand-bus-width: buswidth 8 or 16. If not present 8.
+
+- nand-on-flash-bbt: use flash based bad block table support. OOB
+ identifier is saved in OOB area. If not present
+ false.
+
+Deprecated properties:
+
+- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode
+ valid values for davinci driver:
+ - "none"
+ - "soft"
+ - "hw"
+
+- ti,davinci-nand-buswidth: buswidth 8 or 16. If not present 8.
+
+- ti,davinci-nand-use-bbt: use flash based bad block table support. OOB
+ identifier is saved in OOB area. If not present
+ false.
+
+Nand device bindings may contain additional sub-nodes describing partitions of
+the address space. See partition.txt for more detail. The NAND Flash timing
+values must be programmed in the chip select’s node of AEMIF
+memory-controller (see Documentation/devicetree/bindings/memory-controllers/
+davinci-aemif.txt).
+
+Example(da850 EVM ):
+
+nand_cs3@62000000 {
+ compatible = "ti,davinci-nand";
+ reg = <0x62000000 0x807ff
+ 0x68000000 0x8000>;
+ ti,davinci-chipselect = <1>;
+ ti,davinci-mask-ale = <0>;
+ ti,davinci-mask-cle = <0>;
+ ti,davinci-mask-chipsel = <0>;
+ nand-ecc-mode = "hw";
+ ti,davinci-ecc-bits = <4>;
+ nand-on-flash-bbt;
+
+ partition@180000 {
+ label = "ubifs";
+ reg = <0x180000 0x7e80000>;
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/denali-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/denali-nand.txt
new file mode 100644
index 000000000..b04d03a1d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/denali-nand.txt
@@ -0,0 +1,23 @@
+* Denali NAND controller
+
+Required properties:
+ - compatible : should be "denali,denali-nand-dt"
+ - reg : should contain registers location and length for data and reg.
+ - reg-names: Should contain the reg names "nand_data" and "denali_reg"
+ - interrupts : The interrupt number.
+ - dm-mask : DMA bit mask
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+nand: nand@ff900000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "denali,denali-nand-dt";
+ reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;
+ reg-names = "nand_data", "denali_reg";
+ interrupts = <0 144 4>;
+ dma-mask = <0xffffffff>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/diskonchip.txt b/kernel/Documentation/devicetree/bindings/mtd/diskonchip.txt
new file mode 100644
index 000000000..3e13bfdbe
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/diskonchip.txt
@@ -0,0 +1,15 @@
+M-Systems and Sandisk DiskOnChip devices
+
+M-System DiskOnChip G3
+======================
+The Sandisk (formerly M-Systems) docg3 is a nand device of 64M to 256MB.
+
+Required properties:
+ - compatible: should be "m-systems,diskonchip-g3"
+ - reg: register base and size
+
+Example:
+ docg3: flash@0 {
+ compatible = "m-systems,diskonchip-g3";
+ reg = <0x0 0x2000>;
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/elm.txt b/kernel/Documentation/devicetree/bindings/mtd/elm.txt
new file mode 100644
index 000000000..8c1528c42
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/elm.txt
@@ -0,0 +1,16 @@
+Error location module
+
+Required properties:
+- compatible: Must be "ti,am33xx-elm"
+- reg: physical base address and size of the registers map.
+- interrupts: Interrupt number for the elm.
+
+Optional properties:
+- ti,hwmods: Name of the hwmod associated to the elm
+
+Example:
+elm: elm@0 {
+ compatible = "ti,am3352-elm";
+ reg = <0x48080000 0x2000>;
+ interrupts = <4>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/flctl-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/flctl-nand.txt
new file mode 100644
index 000000000..427f46dc6
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/flctl-nand.txt
@@ -0,0 +1,49 @@
+FLCTL NAND controller
+
+Required properties:
+- compatible : "renesas,shmobile-flctl-sh7372"
+- reg : Address range of the FLCTL
+- interrupts : flste IRQ number
+- nand-bus-width : bus width to NAND chip
+
+Optional properties:
+- dmas: DMA specifier(s)
+- dma-names: name for each DMA specifier. Valid names are
+ "data_tx", "data_rx", "ecc_tx", "ecc_rx"
+
+The DMA fields are not used yet in the driver but are listed here for
+completing the bindings.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+ flctl@e6a30000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "renesas,shmobile-flctl-sh7372";
+ reg = <0xe6a30000 0x100>;
+ interrupts = <0x0d80>;
+
+ nand-bus-width = <16>;
+
+ dmas = <&dmac 1 /* data_tx */
+ &dmac 2;> /* data_rx */
+ dma-names = "data_tx", "data_rx";
+
+ system@0 {
+ label = "system";
+ reg = <0x0 0x8000000>;
+ };
+
+ userdata@8000000 {
+ label = "userdata";
+ reg = <0x8000000 0x10000000>;
+ };
+
+ cache@18000000 {
+ label = "cache";
+ reg = <0x18000000 0x8000000>;
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/kernel/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
new file mode 100644
index 000000000..4461dc71c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
@@ -0,0 +1,35 @@
+* Freescale Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+ - compatible : Should be "fsl,vf610-qspi" or "fsl,imx6sx-qspi"
+ - reg : the first contains the register location and length,
+ the second contains the memory mapping address and length
+ - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
+ - interrupts : Should contain the interrupt for the device
+ - clocks : The clocks needed by the QuadSPI controller
+ - clock-names : the name of the clocks
+
+Optional properties:
+ - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
+ Each bus can be connected with two NOR flashes.
+ Most of the time, each bus only has one NOR flash
+ connected, this is the default case.
+ But if there are two NOR flashes connected to the
+ bus, you should enable this property.
+ (Please check the board's schematic.)
+
+Example:
+
+qspi0: quadspi@40044000 {
+ compatible = "fsl,vf610-qspi";
+ reg = <0x40044000 0x1000>, <0x20000000 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks VF610_CLK_QSPI0_EN>,
+ <&clks VF610_CLK_QSPI0>;
+ clock-names = "qspi_en", "qspi";
+
+ flash0: s25fl128s@0 {
+ ....
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt
new file mode 100644
index 000000000..fce4894f5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt
@@ -0,0 +1,67 @@
+Freescale Localbus UPM programmed to work with NAND flash
+
+Required properties:
+- compatible : "fsl,upm-nand".
+- reg : should specify localbus chip select and size used for the chip.
+- fsl,upm-addr-offset : UPM pattern offset for the address latch.
+- fsl,upm-cmd-offset : UPM pattern offset for the command latch.
+
+Optional properties:
+- fsl,upm-wait-flags : add chip-dependent short delays after running the
+ UPM pattern (0x1), after writing a data byte (0x2) or after
+ writing out a buffer (0x4).
+- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support.
+ The corresponding address lines are used to select the chip.
+- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins
+ (R/B#). For multi-chip devices, "n" GPIO definitions are required
+ according to the number of chips.
+- chip-delay : chip dependent delay for transferring data from array to
+ read registers (tR). Required if property "gpios" is not used
+ (R/B# pins not connected).
+
+Each flash chip described may optionally contain additional sub-nodes
+describing partitions of the address space. See partition.txt for more
+detail.
+
+Examples:
+
+upm@1,0 {
+ compatible = "fsl,upm-nand";
+ reg = <1 0 1>;
+ fsl,upm-addr-offset = <16>;
+ fsl,upm-cmd-offset = <8>;
+ gpios = <&qe_pio_e 18 0>;
+
+ flash {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "...";
+
+ partition@0 {
+ ...
+ };
+ };
+};
+
+upm@3,0 {
+ #address-cells = <0>;
+ #size-cells = <0>;
+ compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand";
+ reg = <3 0x0 0x800>;
+ fsl,upm-addr-offset = <0x10>;
+ fsl,upm-cmd-offset = <0x08>;
+ /* Multi-chip NAND device */
+ fsl,upm-addr-line-cs-offsets = <0x0 0x200>;
+ fsl,upm-wait-flags = <0x5>;
+ chip-delay = <25>; // in micro-seconds
+
+ nand@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "fs";
+ reg = <0x00000000 0x10000000>;
+ };
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
new file mode 100644
index 000000000..5235cbc55
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
@@ -0,0 +1,54 @@
+ST Microelectronics Flexible Static Memory Controller (FSMC)
+NAND Interface
+
+Required properties:
+- compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand"
+- reg : Address range of the mtd chip
+- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd"
+
+Optional properties:
+- bank-width : Width (in bytes) of the device. If not present, the width
+ defaults to 1 byte
+- nand-skip-bbtscan: Indicates the BBT scanning should be skipped
+- timings: array of 6 bytes for NAND timings. The meanings of these bytes
+ are:
+ byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits
+ are valid. Zero means one clockcycle, 15 means 16 clock
+ cycles.
+ byte 1 TAR : ALE to RE delay, 4 bits are valid. Same format as TCLR.
+ byte 2 THIZ : number of HCLK clock cycles during which the data bus is
+ kept in Hi-Z (tristate) after the start of a write access.
+ Only valid for write transactions. Zero means zero cycles,
+ 255 means 255 cycles.
+ byte 3 THOLD : number of HCLK clock cycles to hold the address (and data
+ when writing) after the command deassertation. Zero means
+ one cycle, 255 means 256 cycles.
+ byte 4 TWAIT : number of HCLK clock cycles to assert the command to the
+ NAND flash in response to SMWAITn. Zero means 1 cycle,
+ 255 means 256 cycles.
+ byte 5 TSET : number of HCLK clock cycles to assert the address before the
+ command is asserted. Zero means one cycle, 255 means 256
+ cycles.
+- bank: default NAND bank to use (0-3 are valid, 0 is the default).
+
+Example:
+
+ fsmc: flash@d1800000 {
+ compatible = "st,spear600-fsmc-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd1800000 0x1000 /* FSMC Register */
+ 0xd2000000 0x0010 /* NAND Base DATA */
+ 0xd2020000 0x0010 /* NAND Base ADDR */
+ 0xd2010000 0x0010>; /* NAND Base CMD */
+ reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+
+ bank-width = <1>;
+ nand-skip-bbtscan;
+ timings = /bits/ 8 <0 0 0 2 3 0>;
+ bank = <1>;
+
+ partition@0 {
+ ...
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
new file mode 100644
index 000000000..af8915b41
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
@@ -0,0 +1,47 @@
+GPIO assisted NAND flash
+
+The GPIO assisted NAND flash uses a memory mapped interface to
+read/write the NAND commands and data and GPIO pins for the control
+signals.
+
+Required properties:
+- compatible : "gpio-control-nand"
+- reg : should specify localbus chip select and size used for the chip. The
+ resource describes the data bus connected to the NAND flash and all accesses
+ are made in native endianness.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+ representing partitions.
+- gpios : Specifies the GPIO pins to control the NAND device. The order of
+ GPIO references is: RDY, nCE, ALE, CLE, and an optional nWP.
+
+Optional properties:
+- bank-width : Width (in bytes) of the device. If not present, the width
+ defaults to 1 byte.
+- chip-delay : chip dependent delay for transferring data from array to
+ read registers (tR). If not present then a default of 20us is used.
+- gpio-control-nand,io-sync-reg : A 64-bit physical address for a read
+ location used to guard against bus reordering with regards to accesses to
+ the GPIO's and the NAND flash data bus. If present, then after changing
+ GPIO state and before and after command byte writes, this register will be
+ read to ensure that the GPIO accesses have completed.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+gpio-nand@1,0 {
+ compatible = "gpio-control-nand";
+ reg = <1 0x0000 0x2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ gpios = <&banka 1 0>, /* RDY */
+ <&banka 2 0>, /* nCE */
+ <&banka 3 0>, /* ALE */
+ <&banka 4 0>, /* CLE */
+ <0>; /* nWP */
+
+ partition@0 {
+ ...
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
new file mode 100644
index 000000000..fb733c4e1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -0,0 +1,137 @@
+Device tree bindings for GPMC connected NANDs
+
+GPMC connected NAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "nand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+For NAND specific properties such as ECC modes or bus width, please refer to
+Documentation/devicetree/bindings/mtd/nand.txt
+
+
+Required properties:
+
+ - reg: The CS line the peripheral is connected to
+
+Optional properties:
+
+ - nand-bus-width: Set this numeric value to 16 if the hardware
+ is wired that way. If not specified, a bus
+ width of 8 is assumed.
+
+ - ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
+ "sw" 1-bit Hamming ecc code via software
+ "hw" <deprecated> use "ham1" instead
+ "hw-romcode" <deprecated> use "ham1" instead
+ "ham1" 1-bit Hamming ecc code
+ "bch4" 4-bit BCH ecc code
+ "bch8" 8-bit BCH ecc code
+ "bch16" 16-bit BCH ECC code
+ Refer below "How to select correct ECC scheme for your device ?"
+
+ - ti,nand-xfer-type: A string setting the data transfer type. One of:
+
+ "prefetch-polled" Prefetch polled mode (default)
+ "polled" Polled mode, without prefetch
+ "prefetch-dma" Prefetch enabled sDMA mode
+ "prefetch-irq" Prefetch enabled irq mode
+
+ - elm_id: <deprecated> use "ti,elm-id" instead
+ - ti,elm-id: Specifies phandle of the ELM devicetree node.
+ ELM is an on-chip hardware engine on TI SoC which is used for
+ locating ECC errors for BCHx algorithms. SoC devices which have
+ ELM hardware engines should specify this device node in .dtsi
+ Using ELM for ECC error correction frees some CPU cycles.
+
+For inline partition table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an AM33xx board:
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x50000000 0x1000000>;
+ interrupts = <100>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */
+ elm_id = <&elm>;
+
+ nand@0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+ ti,nand-xfer-type = "polled";
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* partitions go here */
+ };
+ };
+
+How to select correct ECC scheme for your device ?
+--------------------------------------------------
+Higher ECC scheme usually means better protection against bit-flips and
+increased system lifetime. However, selection of ECC scheme is dependent
+on various other factors also like;
+
+(1) support of built in hardware engines.
+ Some legacy OMAP SoC do not have ELM harware engine, so those SoC cannot
+ support ecc-schemes with hardware error-correction (BCHx_HW). However
+ such SoC can use ecc-schemes with software library for error-correction
+ (BCHx_HW_DETECTION_SW). The error correction capability with software
+ library remains equivalent to their hardware counter-part, but there is
+ slight CPU penalty when too many bit-flips are detected during reads.
+
+(2) Device parameters like OOBSIZE.
+ Other factor which governs the selection of ecc-scheme is oob-size.
+ Higher ECC schemes require more OOB/Spare area to store ECC syndrome,
+ so the device should have enough free bytes available its OOB/Spare
+ area to accommodate ECC for entire page. In general following expression
+ helps in determining if given device can accommodate ECC syndrome:
+ "2 + (PAGESIZE / 512) * ECC_BYTES" >= OOBSIZE"
+ where
+ OOBSIZE number of bytes in OOB/spare area
+ PAGESIZE number of bytes in main-area of device page
+ ECC_BYTES number of ECC bytes generated to protect
+ 512 bytes of data, which is:
+ '3' for HAM1_xx ecc schemes
+ '7' for BCH4_xx ecc schemes
+ '14' for BCH8_xx ecc schemes
+ '26' for BCH16_xx ecc schemes
+
+ Example(a): For a device with PAGESIZE = 2048 and OOBSIZE = 64 and
+ trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
+ Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
+ which is greater than capacity of NAND device (OOBSIZE=64)
+ Hence, BCH16 cannot be supported on given device. But it can
+ probably use lower ecc-schemes like BCH8.
+
+ Example(b): For a device with PAGESIZE = 2048 and OOBSIZE = 128 and
+ trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
+ Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
+ which can be accommodated in the OOB/Spare area of this device
+ (OOBSIZE=128). So this device can use BCH16 ecc-scheme.
diff --git a/kernel/Documentation/devicetree/bindings/mtd/gpmc-nor.txt b/kernel/Documentation/devicetree/bindings/mtd/gpmc-nor.txt
new file mode 100644
index 000000000..4828c17bb
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/gpmc-nor.txt
@@ -0,0 +1,98 @@
+Device tree bindings for NOR flash connect to TI GPMC
+
+NOR flash connected to the TI GPMC (found on OMAP boards) are represented as
+child nodes of the GPMC controller with a name of "nor".
+
+All timing relevant properties as well as generic GPMC child properties are
+explained in a separate documents. Please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Required properties:
+- bank-width: Width of NOR flash in bytes. GPMC supports 8-bit and
+ 16-bit devices and so must be either 1 or 2 bytes.
+- compatible: Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+- gpmc,cs-on-ns: Chip-select assertion time
+- gpmc,cs-rd-off-ns: Chip-select de-assertion time for reads
+- gpmc,cs-wr-off-ns: Chip-select de-assertion time for writes
+- gpmc,oe-on-ns: Output-enable assertion time
+- gpmc,oe-off-ns: Output-enable de-assertion time
+- gpmc,we-on-ns Write-enable assertion time
+- gpmc,we-off-ns: Write-enable de-assertion time
+- gpmc,access-ns: Start cycle to first data capture (read access)
+- gpmc,rd-cycle-ns: Total read cycle time
+- gpmc,wr-cycle-ns: Total write cycle time
+- linux,mtd-name: Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+- reg: Chip-select, base address (relative to chip-select)
+ and size of NOR flash. Note that base address will be
+ typically 0 as this is the start of the chip-select.
+
+Optional properties:
+- gpmc,XXX Additional GPMC timings and settings parameters. See
+ Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Optional properties for partition table parsing:
+- #address-cells: should be set to 1
+- #size-cells: should be set to 1
+
+Example:
+
+gpmc: gpmc@6e000000 {
+ compatible = "ti,omap3430-gpmc", "simple-bus";
+ ti,hwmods = "gpmc";
+ reg = <0x6e000000 0x1000>;
+ interrupts = <20>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ ranges = <0 0 0x10000000 0x08000000>;
+
+ nor@0,0 {
+ compatible = "cfi-flash";
+ linux,mtd-name= "intel,pf48f6000m0y1be";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0 0 0x08000000>;
+ bank-width = <2>;
+
+ gpmc,mux-add-data;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <186>;
+ gpmc,cs-wr-off-ns = <186>;
+ gpmc,adv-on-ns = <12>;
+ gpmc,adv-rd-off-ns = <48>;
+ gpmc,adv-wr-off-ns = <48>;
+ gpmc,oe-on-ns = <54>;
+ gpmc,oe-off-ns = <168>;
+ gpmc,we-on-ns = <54>;
+ gpmc,we-off-ns = <168>;
+ gpmc,rd-cycle-ns = <186>;
+ gpmc,wr-cycle-ns = <186>;
+ gpmc,access-ns = <114>;
+ gpmc,page-burst-access-ns = <6>;
+ gpmc,bus-turnaround-ns = <12>;
+ gpmc,cycle2cycle-delay-ns = <18>;
+ gpmc,wr-data-mux-bus-ns = <90>;
+ gpmc,wr-access-ns = <186>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-diffcsen;
+
+ partition@0 {
+ label = "bootloader-nor";
+ reg = <0 0x40000>;
+ };
+ partition@0x40000 {
+ label = "params-nor";
+ reg = <0x40000 0x40000>;
+ };
+ partition@0x80000 {
+ label = "kernel-nor";
+ reg = <0x80000 0x200000>;
+ };
+ partition@0x280000 {
+ label = "filesystem-nor";
+ reg = <0x240000 0x7d80000>;
+ };
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/kernel/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
new file mode 100644
index 000000000..5d8fa527c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
@@ -0,0 +1,46 @@
+Device tree bindings for GPMC connected OneNANDs
+
+GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "onenand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Required properties:
+
+ - reg: The CS line the peripheral is connected to
+ - gpmc,device-width Width of the ONENAND device connected to the GPMC
+ in bytes. Must be 1 or 2.
+
+Optional properties:
+
+ - dma-channel: DMA Channel index
+
+For inline partition table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an OMAP3430 board:
+
+ gpmc: gpmc@6e000000 {
+ compatible = "ti,omap3430-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x6e000000 0x1000000>;
+ interrupts = <20>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ onenand@0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ gpmc,device-width = <2>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* partitions go here */
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
new file mode 100644
index 000000000..d02acaff3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
@@ -0,0 +1,58 @@
+* Freescale General-Purpose Media Interface (GPMI)
+
+The GPMI nand controller provides an interface to control the
+NAND flash chips.
+
+Required properties:
+ - compatible : should be "fsl,<chip>-gpmi-nand"
+ - reg : should contain registers location and length for gpmi and bch.
+ - reg-names: Should contain the reg names "gpmi-nand" and "bch"
+ - interrupts : BCH interrupt number.
+ - interrupt-names : Should be "bch".
+ - dmas: DMA specifier, consisting of a phandle to DMA controller node
+ and GPMI DMA channel ID.
+ Refer to dma.txt and fsl-mxs-dma.txt for details.
+ - dma-names: Must be "rx-tx".
+
+Optional properties:
+ - nand-on-flash-bbt: boolean to enable on flash bbt option if not
+ present false
+ - fsl,use-minimum-ecc: Protect this NAND flash with the minimum ECC
+ strength required. The required ECC strength is
+ automatically discoverable for some flash
+ (e.g., according to the ONFI standard).
+ However, note that if this strength is not
+ discoverable or this property is not enabled,
+ the software may chooses an implementation-defined
+ ECC scheme.
+ - fsl,no-blockmark-swap: Don't swap the bad block marker from the OOB
+ area with the byte in the data area but rely on the
+ flash based BBT for identifying bad blocks.
+ NOTE: this is only valid in conjunction with
+ 'nand-on-flash-bbt'.
+ WARNING: on i.MX28 blockmark swapping cannot be
+ disabled for the BootROM in the FCB. Thus,
+ partitions written from Linux with this feature
+ turned on may not be accessible by the BootROM
+ code.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+gpmi-nand@8000c000 {
+ compatible = "fsl,imx28-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x8000c000 2000>, <0x8000a000 2000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <41>;
+ interrupt-names = "bch";
+ dmas = <&dma_apbh 4>;
+ dma-names = "rx-tx";
+
+ partition@0 {
+ ...
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/hisi504-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/hisi504-nand.txt
new file mode 100644
index 000000000..2e35f0662
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/hisi504-nand.txt
@@ -0,0 +1,47 @@
+Hisilicon Hip04 Soc NAND controller DT binding
+
+Required properties:
+
+- compatible: Should be "hisilicon,504-nfc".
+- reg: The first contains base physical address and size of
+ NAND controller's registers. The second contains base
+ physical address and size of NAND controller's buffer.
+- interrupts: Interrupt number for nfc.
+- nand-bus-width: See nand.txt.
+- nand-ecc-mode: Support none and hw ecc mode.
+- #address-cells: Partition address, should be set 1.
+- #size-cells: Partition size, should be set 1.
+
+Optional properties:
+
+- nand-ecc-strength: Number of bits to correct per ECC step.
+- nand-ecc-step-size: Number of data bytes covered by a single ECC step.
+
+The following ECC strength and step size are currently supported:
+
+ - nand-ecc-strength = <16>, nand-ecc-step-size = <1024>
+
+Flash chip may optionally contain additional sub-nodes describing partitions of
+the address space. See partition.txt for more detail.
+
+Example:
+
+ nand: nand@4020000 {
+ compatible = "hisilicon,504-nfc";
+ reg = <0x4020000 0x10000>, <0x5000000 0x1000>;
+ interrupts = <0 379 4>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <16>;
+ nand-ecc-step-size = <1024>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "nand_text";
+ reg = <0x00000000 0x00400000>;
+ };
+
+ ...
+
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt b/kernel/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
new file mode 100644
index 000000000..2bee68103
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
@@ -0,0 +1,32 @@
+* MTD SPI driver for ST M25Pxx (and similar) serial flash chips
+
+Required properties:
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+ representing partitions.
+- compatible : May include a device-specific string consisting of the
+ manufacturer and name of the chip. Bear in mind the DT binding
+ is not Linux-only, but in case of Linux, see the "m25p_ids"
+ table in drivers/mtd/devices/m25p80.c for the list of supported
+ chips.
+ Must also include "jedec,spi-nor" for any SPI NOR flash that can
+ be identified by the JEDEC READ ID opcode (0x9F).
+- reg : Chip-Select number
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
+
+Optional properties:
+- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead
+ of the usual "read" opcode. This opcode is not supported by
+ all chips and support for it can not be detected at runtime.
+ Refer to your chips' datasheet to check if this is supported
+ by your chip.
+
+Example:
+
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,m25p80", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ m25p,fast-read;
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt b/kernel/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt
new file mode 100644
index 000000000..d0a37252e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt
@@ -0,0 +1,50 @@
+NXP LPC32xx SoC NAND MLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-mlc"
+- reg: Address and size of the controller
+- interrupts: The NAND interrupt specification
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in
+Hz, to make them independent of actual clock speed and to provide for good
+accuracy:)
+- nxp,tcea_delay: TCEA_DELAY
+- nxp,busy_delay: BUSY_DELAY
+- nxp,nand_ta: NAND_TA
+- nxp,rd_high: RD_HIGH
+- nxp,rd_low: RD_LOW
+- nxp,wr_high: WR_HIGH
+- nxp,wr_low: WR_LOW
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+ mlc: flash@200A8000 {
+ compatible = "nxp,lpc3220-mlc";
+ reg = <0x200A8000 0x11000>;
+ interrupts = <11 0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nxp,tcea-delay = <333333333>;
+ nxp,busy-delay = <10000000>;
+ nxp,nand-ta = <18181818>;
+ nxp,rd-high = <31250000>;
+ nxp,rd-low = <45454545>;
+ nxp,wr-high = <40000000>;
+ nxp,wr-low = <83333333>;
+ gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+ mtd0@00000000 {
+ label = "boot";
+ reg = <0x00000000 0x00064000>;
+ read-only;
+ };
+
+ ...
+
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt b/kernel/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt
new file mode 100644
index 000000000..d94edc0fc
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt
@@ -0,0 +1,52 @@
+NXP LPC32xx SoC NAND SLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-slc"
+- reg: Address and size of the controller
+- nand-on-flash-bbt: Use bad block table on flash
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual:
+- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY)
+- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY)
+(The following values are specified in Hz, to make them independent of actual
+clock speed:)
+- nxp,wwidth: Write pulse width (W_WIDTH)
+- nxp,whold: Write hold time (W_HOLD)
+- nxp,wsetup: Write setup time (W_SETUP)
+- nxp,rwidth: Read pulse width (R_WIDTH)
+- nxp,rhold: Read hold time (R_HOLD)
+- nxp,rsetup: Read setup time (R_SETUP)
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+ slc: flash@20020000 {
+ compatible = "nxp,lpc3220-slc";
+ reg = <0x20020000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nxp,wdr-clks = <14>;
+ nxp,wwidth = <40000000>;
+ nxp,whold = <100000000>;
+ nxp,wsetup = <100000000>;
+ nxp,rdr-clks = <14>;
+ nxp,rwidth = <40000000>;
+ nxp,rhold = <66666666>;
+ nxp,rsetup = <100000000>;
+ nand-on-flash-bbt;
+ gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+ mtd0@00000000 {
+ label = "phy3250-boot";
+ reg = <0x00000000 0x00064000>;
+ read-only;
+ };
+
+ ...
+
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/kernel/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
new file mode 100644
index 000000000..4a0a48bf4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
@@ -0,0 +1,89 @@
+CFI or JEDEC memory-mapped NOR flash, MTD-RAM (NVRAM...)
+
+Flash chips (Memory Technology Devices) are often used for solid state
+file systems on embedded devices.
+
+ - compatible : should contain the specific model of mtd chip(s)
+ used, if known, followed by either "cfi-flash", "jedec-flash",
+ "mtd-ram" or "mtd-rom".
+ - reg : Address range(s) of the mtd chip(s)
+ It's possible to (optionally) define multiple "reg" tuples so that
+ non-identical chips can be described in one node.
+ - bank-width : Width (in bytes) of the bank. Equal to the
+ device width times the number of interleaved chips.
+ - device-width : (optional) Width of a single mtd chip. If
+ omitted, assumed to be equal to 'bank-width'.
+ - #address-cells, #size-cells : Must be present if the device has
+ sub-nodes representing partitions (see below). In this case
+ both #address-cells and #size-cells must be equal to 1.
+ - no-unaligned-direct-access: boolean to disable the default direct
+ mapping of the flash.
+ On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
+ problems with JFFS2 usage, as the local bus (LPB) doesn't support
+ unaligned accesses as implemented in the JFFS2 code via memcpy().
+ By defining "no-unaligned-direct-access", the flash will not be
+ exposed directly to the MTD users (e.g. JFFS2) any more.
+ - linux,mtd-name: allow to specify the mtd name for retro capability with
+ physmap-flash drivers as boot loader pass the mtd partition via the old
+ device name physmap-flash.
+ - use-advanced-sector-protection: boolean to enable support for the
+ advanced sector protection (Spansion: PPB - Persistent Protection
+ Bits) locking.
+
+For JEDEC compatible devices, the following additional properties
+are defined:
+
+ - vendor-id : Contains the flash chip's vendor id (1 byte).
+ - device-id : Contains the flash chip's device id (1 byte).
+
+For ROM compatible devices (and ROM fallback from cfi-flash), the following
+additional (optional) property is defined:
+
+ - erase-size : The chip's physical erase block size in bytes.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+ flash@ff000000 {
+ compatible = "amd,am29lv128ml", "cfi-flash";
+ reg = <ff000000 01000000>;
+ bank-width = <4>;
+ device-width = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ fs@0 {
+ label = "fs";
+ reg = <0 f80000>;
+ };
+ firmware@f80000 {
+ label ="firmware";
+ reg = <f80000 80000>;
+ read-only;
+ };
+ };
+
+Here an example with multiple "reg" tuples:
+
+ flash@f0000000,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "intel,PC48F4400P0VB", "cfi-flash";
+ reg = <0 0x00000000 0x02000000
+ 0 0x02000000 0x02000000>;
+ bank-width = <2>;
+ partition@0 {
+ label = "test-part1";
+ reg = <0 0x04000000>;
+ };
+ };
+
+An example using SRAM:
+
+ sram@2,0 {
+ compatible = "samsung,k6f1616u6a", "mtd-ram";
+ reg = <2 0 0x00200000>;
+ bank-width = <2>;
+ };
+
diff --git a/kernel/Documentation/devicetree/bindings/mtd/mxc-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/mxc-nand.txt
new file mode 100644
index 000000000..b5833d11c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/mxc-nand.txt
@@ -0,0 +1,19 @@
+* Freescale's mxc_nand
+
+Required properties:
+- compatible: "fsl,imxXX-nand"
+- reg: address range of the nfc block
+- interrupts: irq to be used
+- nand-bus-width: see nand.txt
+- nand-ecc-mode: see nand.txt
+- nand-on-flash-bbt: see nand.txt
+
+Example:
+
+ nand@d8000000 {
+ compatible = "fsl,imx27-nand";
+ reg = <0xd8000000 0x1000>;
+ interrupts = <29>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/nand.txt b/kernel/Documentation/devicetree/bindings/mtd/nand.txt
new file mode 100644
index 000000000..b53f92e25
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/nand.txt
@@ -0,0 +1,21 @@
+* MTD generic binding
+
+- nand-ecc-mode : String, operation mode of the NAND ecc mode.
+ Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
+ "soft_bch".
+- nand-bus-width : 8 or 16 bus width if not present 8
+- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
+
+- nand-ecc-strength: integer representing the number of bits to correct
+ per ECC step.
+
+- nand-ecc-step-size: integer representing the number of data bytes
+ that are covered by a single ECC step.
+
+The ECC strength and ECC step size properties define the correction capability
+of a controller. Together, they say a controller can correct "{strength} bit
+errors per {size} bytes".
+
+The interpretation of these parameters is implementation-defined, so not all
+implementations must support all possible combinations. However, implementations
+are encouraged to further specify the value(s) they support.
diff --git a/kernel/Documentation/devicetree/bindings/mtd/orion-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/orion-nand.txt
new file mode 100644
index 000000000..2d6ab660e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/orion-nand.txt
@@ -0,0 +1,50 @@
+NAND support for Marvell Orion SoC platforms
+
+Required properties:
+- compatible : "marvell,orion-nand".
+- reg : Base physical address of the NAND and length of memory mapped
+ region
+
+Optional properties:
+- cle : Address line number connected to CLE. Default is 0
+- ale : Address line number connected to ALE. Default is 1
+- bank-width : Width in bytes of the device. Default is 1
+- chip-delay : Chip dependent delay for transferring data from array to read
+ registers in usecs
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+nand@f4000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cle = <0>;
+ ale = <1>;
+ bank-width = <1>;
+ chip-delay = <25>;
+ compatible = "marvell,orion-nand";
+ reg = <0xf4000000 0x400>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x200000>;
+ };
+
+ partition@300000 {
+ label = "dtb";
+ reg = <0x0300000 0x100000>;
+ };
+
+ partition@400000 {
+ label = "root";
+ reg = <0x0400000 0x7d00000>;
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/partition.txt b/kernel/Documentation/devicetree/bindings/mtd/partition.txt
new file mode 100644
index 000000000..8e5557da1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/partition.txt
@@ -0,0 +1,71 @@
+Representing flash partitions in devicetree
+
+Partitions can be represented by sub-nodes of an mtd device. This can be used
+on platforms which have strong conventions about which portions of a flash are
+used for what purposes, but which don't use an on-flash partition table such
+as RedBoot.
+NOTE: if the sub-node has a compatible string, then it is not a partition.
+
+#address-cells & #size-cells must both be present in the mtd device. There are
+two valid values for both:
+<1>: for partitions that require a single 32-bit cell to represent their
+ size/address (aka the value is below 4 GiB)
+<2>: for partitions that require two 32-bit cells to represent their
+ size/address (aka the value is 4 GiB or greater).
+
+Required properties:
+- reg : The partition's offset and size within the mtd bank.
+
+Optional properties:
+- label : The label / name for this partition. If omitted, the label is taken
+ from the node name (excluding the unit address).
+- read-only : This parameter, if present, is a hint to Linux that this
+ partition should only be mounted read-only. This is usually used for flash
+ partitions containing early-boot firmware images or data which should not be
+ clobbered.
+
+Examples:
+
+
+flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ uimage@100000 {
+ reg = <0x0100000 0x200000>;
+ };
+};
+
+flash@1 {
+ #address-cells = <1>;
+ #size-cells = <2>;
+
+ /* a 4 GiB partition */
+ partition@0 {
+ label = "filesystem";
+ reg = <0x00000000 0x1 0x00000000>;
+ };
+};
+
+flash@2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ /* an 8 GiB partition */
+ partition@0 {
+ label = "filesystem #1";
+ reg = <0x0 0x00000000 0x2 0x00000000>;
+ };
+
+ /* a 4 GiB partition */
+ partition@200000000 {
+ label = "filesystem #2";
+ reg = <0x2 0x00000000 0x1 0x00000000>;
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
new file mode 100644
index 000000000..4f833e3c4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
@@ -0,0 +1,43 @@
+PXA3xx NAND DT bindings
+
+Required properties:
+
+ - compatible: Should be set to one of the following:
+ marvell,pxa3xx-nand
+ marvell,armada370-nand
+ - reg: The register base for the controller
+ - interrupts: The interrupt to map
+ - #address-cells: Set to <1> if the node includes partitions
+
+Optional properties:
+
+ - marvell,nand-enable-arbiter: Set to enable the bus arbiter
+ - marvell,nand-keep-config: Set to keep the NAND controller config as set
+ by the bootloader
+ - num-cs: Number of chipselect lines to use
+ - nand-on-flash-bbt: boolean to enable on flash bbt option if
+ not present false
+ - nand-ecc-strength: number of bits to correct per ECC step
+ - nand-ecc-step-size: number of data bytes covered by a single ECC step
+
+The following ECC strength and step size are currently supported:
+
+ - nand-ecc-strength = <1>, nand-ecc-step-size = <512>
+ - nand-ecc-strength = <4>, nand-ecc-step-size = <512>
+ - nand-ecc-strength = <8>, nand-ecc-step-size = <512>
+
+Example:
+
+ nand0: nand@43100000 {
+ compatible = "marvell,pxa3xx-nand";
+ reg = <0x43100000 90>;
+ interrupts = <45>;
+ #address-cells = <1>;
+
+ marvell,nand-enable-arbiter;
+ marvell,nand-keep-config;
+ num-cs = <1>;
+
+ /* partitions (optional) */
+ };
+
diff --git a/kernel/Documentation/devicetree/bindings/mtd/spear_smi.txt b/kernel/Documentation/devicetree/bindings/mtd/spear_smi.txt
new file mode 100644
index 000000000..7248aadd8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/spear_smi.txt
@@ -0,0 +1,31 @@
+* SPEAr SMI
+
+Required properties:
+- compatible : "st,spear600-smi"
+- reg : Address range of the mtd chip
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+ representing partitions.
+- interrupt-parent: Should be the phandle for the interrupt controller
+ that services interrupts for this device
+- interrupts: Should contain the STMMAC interrupts
+- clock-rate : Functional clock rate of SMI in Hz
+
+Optional properties:
+- st,smi-fast-mode : Flash supports read in fast mode
+
+Example:
+
+ smi: flash@fc000000 {
+ compatible = "st,spear600-smi";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xfc000000 0x1000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <12>;
+ clock-rate = <50000000>; /* 50MHz */
+
+ flash@f8000000 {
+ st,smi-fast-mode;
+ ...
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/mtd/st-fsm.txt b/kernel/Documentation/devicetree/bindings/mtd/st-fsm.txt
new file mode 100644
index 000000000..c2489391c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/st-fsm.txt
@@ -0,0 +1,26 @@
+* ST-Microelectronics SPI FSM Serial (NOR) Flash Controller
+
+Required properties:
+ - compatible : Should be "st,spi-fsm"
+ - reg : Contains register's location and length.
+ - reg-names : Should contain the reg names "spi-fsm"
+ - interrupts : The interrupt number
+ - pinctrl-0 : Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt)
+
+Optional properties:
+ - st,syscfg : Phandle to boot-device system configuration registers
+ - st,boot-device-reg : Address of the aforementioned boot-device register(s)
+ - st,boot-device-spi : Expected boot-device value if booted via this device
+
+Example:
+ spifsm: spifsm@fe902000{
+ compatible = "st,spi-fsm";
+ reg = <0xfe902000 0x1000>;
+ reg-names = "spi-fsm";
+ pinctrl-0 = <&pinctrl_fsm>;
+ st,syscfg = <&syscfg_rear>;
+ st,boot-device-reg = <0x958>;
+ st,boot-device-spi = <0x1a>;
+ status = "okay";
+ };
+
diff --git a/kernel/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/kernel/Documentation/devicetree/bindings/mtd/sunxi-nand.txt
new file mode 100644
index 000000000..086d6f44c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mtd/sunxi-nand.txt
@@ -0,0 +1,45 @@
+Allwinner NAND Flash Controller (NFC)
+
+Required properties:
+- compatible : "allwinner,sun4i-a10-nand".
+- reg : shall contain registers location and length for data and reg.
+- interrupts : shall define the nand controller interrupt.
+- #address-cells: shall be set to 1. Encode the nand CS.
+- #size-cells : shall be set to 0.
+- clocks : shall reference nand controller clocks.
+- clock-names : nand controller internal clock names. Shall contain :
+ * "ahb" : AHB gating clock
+ * "mod" : nand controller clock
+
+Optional children nodes:
+Children nodes represent the available nand chips.
+
+Optional properties:
+- allwinner,rb : shall contain the native Ready/Busy ids.
+ or
+- rb-gpios : shall contain the gpios used as R/B pins.
+- nand-ecc-mode : one of the supported ECC modes ("hw", "hw_syndrome", "soft",
+ "soft_bch" or "none")
+
+see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings.
+
+
+Examples:
+nfc: nand@01c03000 {
+ compatible = "allwinner,sun4i-a10-nand";
+ reg = <0x01c03000 0x1000>;
+ interrupts = <0 37 1>;
+ clocks = <&ahb_gates 13>, <&nand_clk>;
+ clock-names = "ahb", "mod";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>;
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ allwinner,rb = <0>;
+ nand-ecc-mode = "soft_bch";
+ };
+};