summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/devicetree/bindings/mmc/mmc.txt
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/mmc/mmc.txt')
-rw-r--r--kernel/Documentation/devicetree/bindings/mmc/mmc.txt140
1 files changed, 140 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/mmc/mmc.txt b/kernel/Documentation/devicetree/bindings/mmc/mmc.txt
new file mode 100644
index 000000000..438899e88
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -0,0 +1,140 @@
+These properties are common to multiple MMC host controllers. Any host
+that requires the respective functionality should implement them using
+these definitions.
+
+Interpreted by the OF core:
+- reg: Registers location and length.
+- interrupts: Interrupts used by the MMC controller.
+
+Card detection:
+If no property below is supplied, host native card detect is used.
+Only one of the properties in this section should be supplied:
+ - broken-cd: There is no card detection available; polling must be used.
+ - cd-gpios: Specify GPIOs for card detection, see gpio binding
+ - non-removable: non-removable slot (like eMMC); assume always present.
+
+Optional properties:
+- bus-width: Number of data lines, can be <1>, <4>, or <8>. The default
+ will be <1> if the property is absent.
+- wp-gpios: Specify GPIOs for write protection, see gpio binding
+- cd-inverted: when present, polarity on the CD line is inverted. See the note
+ below for the case, when a GPIO is used for the CD line
+- wp-inverted: when present, polarity on the WP line is inverted. See the note
+ below for the case, when a GPIO is used for the WP line
+- max-frequency: maximum operating clock frequency
+- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
+ this system, even if the controller claims it is.
+- cap-sd-highspeed: SD high-speed timing is supported
+- cap-mmc-highspeed: MMC high-speed timing is supported
+- sd-uhs-sdr12: SD UHS SDR12 speed is supported
+- sd-uhs-sdr25: SD UHS SDR25 speed is supported
+- sd-uhs-sdr50: SD UHS SDR50 speed is supported
+- sd-uhs-sdr104: SD UHS SDR104 speed is supported
+- sd-uhs-ddr50: SD UHS DDR50 speed is supported
+- cap-power-off-card: powering off the card is safe
+- cap-sdio-irq: enable SDIO IRQ signalling on this interface
+- full-pwr-cycle: full power cycle of the card is supported
+- mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported
+- mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported
+- mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported
+- mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported
+- mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported
+- mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported
+- dsr: Value the card's (optional) Driver Stage Register (DSR) should be
+ programmed with. Valid range: [0 .. 0xffff].
+
+*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
+polarity properties, we have to fix the meaning of the "normal" and "inverted"
+line levels. We choose to follow the SDHCI standard, which specifies both those
+lines as "active low." Therefore, using the "cd-inverted" property means, that
+the CD line is active high, i.e. it is high, when a card is inserted. Similar
+logic applies to the "wp-inverted" property.
+
+CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs,
+specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of
+dedicated pins can be specified, using *-inverted properties. GPIO polarity can
+also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity
+in the latter case. We choose to use the XOR logic for GPIO CD and WP lines.
+This means, the two properties are "superimposed," for example leaving the
+OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted
+property results in a double-inversion and actually means the "normal" line
+polarity is in effect.
+
+Optional SDIO properties:
+- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
+- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion
+
+
+MMC power sequences:
+--------------------
+
+System on chip designs may specify a specific MMC power sequence. To
+successfully detect an (e)MMC/SD/SDIO card, that power sequence must be
+maintained while initializing the card.
+
+Optional property:
+- mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*"
+ for documentation of MMC power sequence bindings.
+
+
+Use of Function subnodes
+------------------------
+
+On embedded systems the cards connected to a host may need additional
+properties. These can be specified in subnodes to the host controller node.
+The subnodes are identified by the standard 'reg' property.
+Which information exactly can be specified depends on the bindings for the
+SDIO function driver for the subnode, as specified by the compatible string.
+
+Required host node properties when using function subnodes:
+- #address-cells: should be one. The cell is the slot id.
+- #size-cells: should be zero.
+
+Required function subnode properties:
+- compatible: name of SDIO function following generic names recommended practice
+- reg: Must contain the SDIO function number of the function this subnode
+ describes. A value of 0 denotes the memory SD function, values from
+ 1 to 7 denote the SDIO functions.
+
+
+Examples
+--------
+
+Basic example:
+
+sdhci@ab000000 {
+ compatible = "sdhci";
+ reg = <0xab000000 0x200>;
+ interrupts = <23>;
+ bus-width = <4>;
+ cd-gpios = <&gpio 69 0>;
+ cd-inverted;
+ wp-gpios = <&gpio 70 0>;
+ max-frequency = <50000000>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ mmc-pwrseq = <&sdhci0_pwrseq>
+}
+
+Example with sdio function subnode:
+
+mmc3: mmc@01c12000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <&reg_vmmc3>;
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&sdhci0_pwrseq>
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm43xx-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <10 8>; /* PH10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};