2 files changed, 139 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt b/kernel/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
new file mode 100644
index 000000000..973c27273
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
@@ -0,0 +1,98 @@
+MIPI DSI (Display Serial Interface) busses
+==========================================
+
+The MIPI Display Serial Interface specifies a serial bus and a protocol for
+communication between a host and up to four peripherals. This document will
+define the syntax used to represent a DSI bus in a device tree.
+
+This document describes DSI bus-specific properties only or defines existing
+standard properties in the context of the DSI bus.
+
+Each DSI host provides a DSI bus. The DSI host controller's node contains a
+set of properties that characterize the bus. Child nodes describe individual
+peripherals on that bus.
+
+The following assumes that only a single peripheral is connected to a DSI
+host. Experience shows that this is true for the large majority of setups.
+
+DSI host
+--------
+
+In addition to the standard properties and those defined by the parent bus of
+a DSI host, the following properties apply to a node representing a DSI host.
+
+Required properties:
+- #address-cells: The number of cells required to represent an address on the
+  bus. DSI peripherals are addressed using a 2-bit virtual channel number, so
+  a maximum of 4 devices can be addressed on a single bus. Hence the value of
+  this property should be 1.
+- #size-cells: Should be 0. There are cases where it makes sense to use a
+  different value here. See below.
+
+DSI peripheral
+--------------
+
+Peripherals are represented as child nodes of the DSI host's node. Properties
+described here apply to all DSI peripherals, but individual bindings may want
+to define additional, device-specific properties.
+
+Required properties:
+- reg: The virtual channel number of a DSI peripheral. Must be in the range
+  from 0 to 3.
+
+Some DSI peripherals respond to more than a single virtual channel. In that
+case two alternative representations can be chosen:
+- The reg property can take multiple entries, one for each virtual channel
+  that the peripheral responds to.
+- If the virtual channels that a peripheral responds to are consecutive, the
+  #size-cells can be set to 1. The first cell of each entry in the reg
+  property is the number of the first virtual channel and the second cell is
+  the number of consecutive virtual channels.
+
+Example
+-------
+
+	dsi-host {
+		...
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* peripheral responds to virtual channel 0 */
+		peripheral@0 {
+			compatible = "...";
+			reg = <0>;
+		};
+
+		...
+	};
+
+	dsi-host {
+		...
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* peripheral responds to virtual channels 0 and 2 */
+		peripheral@0 {
+			compatible = "...";
+			reg = <0, 2>;
+		};
+
+		...
+	};
+
+	dsi-host {
+		...
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* peripheral responds to virtual channels 1, 2 and 3 */
+		peripheral@1 {
+			compatible = "...";
+			reg = <1 3>;
+		};
+
+		...
+	};
diff --git a/kernel/Documentation/devicetree/bindings/mipi/nvidia,tegra114-mipi.txt b/kernel/Documentation/devicetree/bindings/mipi/nvidia,tegra114-mipi.txt
new file mode 100644
index 000000000..e4a25cedc
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mipi/nvidia,tegra114-mipi.txt
@@ -0,0 +1,41 @@
+NVIDIA Tegra MIPI pad calibration controller
+
+Required properties:
+- compatible: "nvidia,tegra<chip>-mipi"
+- reg: Physical base address and length of the controller's registers.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - mipi-cal
+- #nvidia,mipi-calibrate-cells: Should be 1. The cell is a bitmask of the pads
+  that need to be calibrated for a given device.
+
+User nodes need to contain an nvidia,mipi-calibrate property that has a
+phandle to refer to the calibration controller node and a bitmask of the pads
+that need to be calibrated.
+
+Example:
+
+	mipi: mipi@700e3000 {
+		compatible = "nvidia,tegra114-mipi";
+		reg = <0x700e3000 0x100>;
+		clocks = <&tegra_car TEGRA114_CLK_MIPI_CAL>;
+		clock-names = "mipi-cal";
+		#nvidia,mipi-calibrate-cells = <1>;
+	};
+
+	...
+
+	host1x@50000000 {
+		...
+
+		dsi@54300000 {
+			...
+
+			nvidia,mipi-calibrate = <&mipi 0x060>;
+
+			...
+		};
+
+		...
+	};