diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/mfd')
17 files changed, 423 insertions, 93 deletions
diff --git a/kernel/Documentation/devicetree/bindings/mfd/arizona.txt b/kernel/Documentation/devicetree/bindings/mfd/arizona.txt index 7665aa959..18be0cbfb 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/arizona.txt @@ -10,6 +10,9 @@ Required properties: "wlf,wm5110" "wlf,wm8280" "wlf,wm8997" + "wlf,wm8998" + "wlf,wm1814" + - reg : I2C slave address when connected using I2C, chip select number when using SPI. @@ -31,17 +34,16 @@ Required properties: as covered in Documentation/devicetree/bindings/regulator/regulator.txt - DBVDD2-supply, DBVDD3-supply : Additional databus power supplies (wm5102, - wm5110, wm8280) + wm5110, wm8280, wm8998, wm1814) - SPKVDDL-supply, SPKVDDR-supply : Speaker driver power supplies (wm5102, - wm5110, wm8280) + wm5110, wm8280, wm8998, wm1814) - SPKVDD-supply : Speaker driver power supply (wm8997) Optional properties: - wlf,reset : GPIO specifier for the GPIO controlling /RESET - - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA - wlf,gpio-defaults : A list of GPIO configuration register values. Defines for the appropriate values can found in <dt-bindings/mfd/arizona.txt>. If @@ -53,8 +55,10 @@ Optional properties: of input signals. Valid values are 0 (Differential), 1 (Single-ended) and 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default. If present, values must be specified less than or equal to the number of - input singals. If values less than the number of input signals, elements - that has not been specifed are set to 0 by default. + input signals. If values less than the number of input signals, elements + that have not been specified are set to 0 by default. Entries are: + <IN1, IN2, IN3, IN4> (wm5102, wm5110, wm8280, wm8997) + <IN1A, IN2A, IN1B, IN2B> (wm8998, wm1814) - wlf,dmic-ref : DMIC reference voltage source for each input, can be selected from either MICVDD or one of the MICBIAS's, defines @@ -66,11 +70,9 @@ Optional properties: they are being externally supplied. As covered in Documentation/devicetree/bindings/regulator/regulator.txt -Optional subnodes: - - ldo1 : Initial data for the LDO1 regulator, as covered in - Documentation/devicetree/bindings/regulator/regulator.txt - - micvdd : Initial data for the MICVDD regulator, as covered in - Documentation/devicetree/bindings/regulator/regulator.txt +Also see child specific device properties: + Regulator - ../regulator/arizona-regulator.txt + Extcon - ../extcon/extcon-arizona.txt Example: diff --git a/kernel/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/kernel/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt new file mode 100644 index 000000000..692300117 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt @@ -0,0 +1,63 @@ +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit) + +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C +controller and an USART. Only one function can be used at a time and is chosen +at boot time according to the device tree. + +Required properties: +- compatible: Should be "atmel,sama5d2-flexcom" +- reg: Should be the offset/length value for Flexcom dedicated + I/O registers (without USART, TWI or SPI registers). +- clocks: Should be the Flexcom peripheral clock from PMC. +- #address-cells: Should be <1> +- #size-cells: Should be <1> +- ranges: Should be one range for the full I/O register region + (including USART, TWI and SPI registers). +- atmel,flexcom-mode: Should be one of the following values: + - <1> for USART + - <2> for SPI + - <3> for I2C + +Required child: +A single available child device of type matching the "atmel,flexcom-mode" +property. + +The phandle provided by the clocks property of the child is the same as one for +the Flexcom parent. + +For other properties, please refer to the documentations of the respective +device: +- ../serial/atmel-usart.txt +- ../spi/spi_atmel.txt +- ../i2c/i2c-at91.txt + +Example: + +flexcom@f8034000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xf8034000 0x200>; + clocks = <&flx0_clk>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xf8034000 0x800>; + atmel,flexcom-mode = <2>; + + spi@400 { + compatible = "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx0_default>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&flx0_clk>; + clock-names = "spi_clk"; + atmel,fifo-size = <32>; + + mtd_dataflash@0 { + compatible = "atmel,at25f512b"; + reg = <0>; + spi-max-frequency = <20000000>; + }; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/kernel/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt index f64de95a8..670831b29 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -2,7 +2,11 @@ Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver Required properties: - compatible: value should be one of the following: + "atmel,at91sam9n12-hlcdc" + "atmel,at91sam9x5-hlcdc" + "atmel,sama5d2-hlcdc" "atmel,sama5d3-hlcdc" + "atmel,sama5d4-hlcdc" - reg: base address and size of the HLCDC device registers. - clock-names: the name of the 3 clocks requested by the HLCDC device. Should contain "periph_clk", "sys_clk" and "slow_clk". @@ -11,7 +15,7 @@ Required properties: The HLCDC IP exposes two subdevices: - a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt - - a Display Controller: see ../drm/atmel-hlcdc-dc.txt + - a Display Controller: see ../display/atmel-hlcdc-dc.txt Example: diff --git a/kernel/Documentation/devicetree/bindings/mfd/axp20x.txt b/kernel/Documentation/devicetree/bindings/mfd/axp20x.txt index 98685f291..a474359dd 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -1,15 +1,18 @@ -AXP202/AXP209 device tree bindings +AXP family PMIC device tree bindings The axp20x family current members : +axp152 (X-Powers) axp202 (X-Powers) axp209 (X-Powers) +axp221 (X-Powers) Required properties: -- compatible: "x-powers,axp202" or "x-powers,axp209" +- compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209", + "x-powers,axp221" - reg: The I2C slave address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin -- interrupt-controller: axp20x has its own internal IRQs +- interrupt-controller: The PMIC has its own internal IRQs - #interrupt-cells: Should be set to 1 Optional properties: @@ -48,6 +51,31 @@ LDO3 : LDO : ldo3in-supply LDO4 : LDO : ldo24in-supply : shared supply LDO5 : LDO : ldo5in-supply +AXP221 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply +DC1SW : On/Off Switch : : DCDC1 secondary output +DC5LDO : LDO : : input from DCDC5 +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +DLDO3 : LDO : dldoin-supply : shared supply +DLDO4 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on + Example: axp209: pmic@34 { diff --git a/kernel/Documentation/devicetree/bindings/mfd/cros-ec.txt b/kernel/Documentation/devicetree/bindings/mfd/cros-ec.txt index 8009c3d87..136e0c2da 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/cros-ec.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -18,6 +18,10 @@ Required properties (SPI): - reg: SPI chip select Optional properties (SPI): +- google,cros-ec-spi-pre-delay: Some implementations of the EC need a little + time to wake up from sleep before they can receive SPI transfers at a high + clock rate. This property specifies the delay, in usecs, between the + assertion of the CS to the start of the first clock pulse. - google,cros-ec-spi-msg-delay: Some implementations of the EC require some additional processing time in order to accept new transactions. If the delay between transactions is not long enough the EC may not be able to respond @@ -30,6 +34,10 @@ Required properties (LPC): - compatible: "google,cros-ec-lpc" - reg: List of (IO address, size) pairs defining the interface uses +Optional properties (all): +- google,has-vbc-nvram: Some implementations of the EC include a small + nvram space used to store verified boot context data. This boolean flag + is used to specify whether this nvram is present or not. Example for I2C: diff --git a/kernel/Documentation/devicetree/bindings/mfd/da9062.txt b/kernel/Documentation/devicetree/bindings/mfd/da9062.txt new file mode 100644 index 000000000..38802b54d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/mfd/da9062.txt @@ -0,0 +1,88 @@ +* Dialog DA9062 Power Management Integrated Circuit (PMIC) + +DA9062 consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +da9062-regulator : : LDOs & BUCKs +da9062-rtc : : Real-Time Clock +da9062-watchdog : : Watchdog Timer + +====== + +Required properties: + +- compatible : Should be "dlg,da9062". +- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be + modified to match the chip's OTP settings). +- interrupt-parent : Specifies the reference to the interrupt controller for + the DA9062. +- interrupts : IRQ line information. +- interrupt-controller + +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for +further information on IRQ bindings. + +Sub-nodes: + +- regulators : This node defines the settings for the LDOs and BUCKs. The + DA9062 regulators are bound using their names listed below: + + buck1 : BUCK_1 + buck2 : BUCK_2 + buck3 : BUCK_3 + buck4 : BUCK_4 + ldo1 : LDO_1 + ldo2 : LDO_2 + ldo3 : LDO_3 + ldo4 : LDO_4 + + The component follows the standard regulator framework and the bindings + details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + + +- rtc : This node defines settings required for the Real-Time Clock associated + with the DA9062. There are currently no entries in this binding, however + compatible = "dlg,da9062-rtc" should be added if a node is created. + +- watchdog: This node defines the settings for the watchdog driver associated + with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added + if a node is created. + + +Example: + + pmic0: da9062@58 { + compatible = "dlg,da9062"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + rtc { + compatible = "dlg,da9062-rtc"; + }; + + watchdog { + compatible = "dlg,da9062-watchdog"; + }; + + regulators { + DA9062_BUCK1: buck1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <500000>; + regulator-max-microamp = <2000000>; + regulator-boot-on; + }; + DA9062_LDO1: ldo1 { + regulator-name = "LDO_1"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3600000>; + regulator-boot-on; + }; + }; + }; + diff --git a/kernel/Documentation/devicetree/bindings/mfd/da9063.txt b/kernel/Documentation/devicetree/bindings/mfd/da9063.txt index 42c6fa6f1..05b21bcb8 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/da9063.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/da9063.txt @@ -5,6 +5,7 @@ DA9093 consists of a large and varied group of sub-devices (I2C Only): Device Supply Names Description ------ ------------ ----------- da9063-regulator : : LDOs & BUCKs +da9063-onkey : : On Key da9063-rtc : : Real-Time Clock da9063-watchdog : : Watchdog @@ -51,6 +52,18 @@ Sub-nodes: the DA9063. There are currently no entries in this binding, however compatible = "dlg,da9063-rtc" should be added if a node is created. +- onkey : This node defines the OnKey settings for controlling the key + functionality of the device. The node should contain the compatible property + with the value "dlg,da9063-onkey". + + Optional onkey properties: + + - dlg,disable-key-power : Disable power-down using a long key-press. If this + entry exists the OnKey driver will remove support for the KEY_POWER key + press. If this entry does not exist then by default the key-press + triggered power down is enabled and the OnKey will support both KEY_POWER + and KEY_SLEEP. + - watchdog : This node defines settings for the Watchdog timer associated with the DA9063. There are currently no entries in this binding, however compatible = "dlg,da9063-watchdog" should be added if a node is created. @@ -73,6 +86,11 @@ Example: compatible = "dlg,da9063-watchdog"; }; + onkey { + compatible = "dlg,da9063-onkey"; + dlg,disable-key-power; + }; + regulators { DA9063_BCORE1: bcore1 { regulator-name = "BCORE1"; diff --git a/kernel/Documentation/devicetree/bindings/mfd/da9150.txt b/kernel/Documentation/devicetree/bindings/mfd/da9150.txt index d0588eaa0..fd4dca7f4 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/da9150.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/da9150.txt @@ -6,6 +6,7 @@ Device Description ------ ----------- da9150-gpadc : General Purpose ADC da9150-charger : Battery Charger +da9150-fg : Battery Fuel-Gauge ====== @@ -16,13 +17,13 @@ Required properties: the IRQs from da9150 are delivered to. - interrupts: IRQ line info for da9150 chip. - interrupt-controller: da9150 has internal IRQs (own IRQ domain). - (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for + (See ../interrupt-controller/interrupts.txt for further information relating to interrupt properties) Sub-devices: -- da9150-gpadc: See Documentation/devicetree/bindings/iio/adc/da9150-gpadc.txt -- da9150-charger: See Documentation/devicetree/bindings/power/da9150-charger.txt - +- da9150-gpadc: See ../iio/adc/da9150-gpadc.txt +- da9150-charger: See ../power/da9150-charger.txt +- da9150-fg: See ../power/da9150-fg.txt Example: @@ -34,10 +35,28 @@ Example: interrupt-controller; gpadc: da9150-gpadc { - ... + compatible = "dlg,da9150-gpadc"; + #io-channel-cells = <1>; + }; + + charger { + compatible = "dlg,da9150-charger"; + + io-channels = <&gpadc 0>, + <&gpadc 2>, + <&gpadc 8>, + <&gpadc 5>; + io-channel-names = "CHAN_IBUS", + "CHAN_VBUS", + "CHAN_TJUNC", + "CHAN_VBAT"; }; - da9150-charger { - ... + fuel-gauge { + compatible = "dlg,da9150-fuel-gauge"; + + dlg,update-interval = <10000>; + dlg,warn-soc-level = /bits/ 8 <15>; + dlg,crit-soc-level = /bits/ 8 <5> }; }; diff --git a/kernel/Documentation/devicetree/bindings/mfd/max77686.txt b/kernel/Documentation/devicetree/bindings/mfd/max77686.txt index e39f0bc1f..741e76688 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/max77686.txt @@ -1,14 +1,15 @@ Maxim MAX77686 multi-function device -MAX77686 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is +MAX77686 is a Multifunction device with PMIC, RTC and Charger on chip. It is interfaced to host controller using i2c interface. PMIC and Charger submodules are addressed using same i2c slave address whereas RTC submodule uses different i2c slave address,presently for which we are statically creating i2c client while probing.This document describes the binding for mfd device and PMIC submodule. -Binding for the built-in 32k clock generator block is defined separately -in bindings/clk/maxim,max77686.txt file. +Bindings for the built-in 32k clock generator block and +regulators are defined in ../clk/maxim,max77686.txt and +../regulator/max77686.txt respectively. Required properties: - compatible : Must be "maxim,max77686"; @@ -16,67 +17,11 @@ Required properties: - interrupts : This i2c device has an IRQ line connected to the main SoC. - interrupt-parent : The parent interrupt controller. -Optional node: -- voltage-regulators : The regulators of max77686 have to be instantiated - under subnode named "voltage-regulators" using the following format. - - regulator_name { - regulator-compatible = LDOn/BUCKn - standard regulator constraints.... - }; - refer Documentation/devicetree/bindings/regulator/regulator.txt - - The regulator-compatible property of regulator should initialized with string -to get matched with their hardware counterparts as follow: - - -LDOn : for LDOs, where n can lie in range 1 to 26. - example: LDO1, LDO2, LDO26. - -BUCKn : for BUCKs, where n can lie in range 1 to 9. - example: BUCK1, BUCK5, BUCK9. - - Regulators which can be turned off during system suspend: - -LDOn : 2, 6-8, 10-12, 14-16, - -BUCKn : 1-4. - Use standard regulator bindings for it ('regulator-off-in-suspend'). - - LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable - control. To turn this feature on this property must be added to the regulator - sub-node: - - maxim,ena-gpios : one GPIO specifier enable control (the gpio - flags are actually ignored and always - ACTIVE_HIGH is used) - Example: - max77686@09 { + max77686: pmic@09 { compatible = "maxim,max77686"; interrupt-parent = <&wakeup_eint>; interrupts = <26 0>; reg = <0x09>; - - voltage-regulators { - ldo11_reg { - regulator-compatible = "LDO11"; - regulator-name = "vdd_ldo11"; - regulator-min-microvolt = <1900000>; - regulator-max-microvolt = <1900000>; - regulator-always-on; - }; - - buck1_reg { - regulator-compatible = "BUCK1"; - regulator-name = "vdd_mif"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - regulator-boot-on; - }; - - buck9_reg { - regulator-compatible = "BUCK9"; - regulator-name = "CAM_ISP_CORE_1.2V"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1200000>; - maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>; - }; - } + }; diff --git a/kernel/Documentation/devicetree/bindings/mfd/max77693.txt b/kernel/Documentation/devicetree/bindings/mfd/max77693.txt index 38e64405e..d3425846a 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/max77693.txt @@ -76,7 +76,60 @@ Optional properties: Valid values: 4300000, 4700000, 4800000, 4900000 Default: 4300000 +- led : the LED submodule device node + +There are two LED outputs available - FLED1 and FLED2. Each of them can +control a separate LED or they can be connected together to double +the maximum current for a single connected LED. One LED is represented +by one child node. + +Required properties: +- compatible : Must be "maxim,max77693-led". + +Optional properties: +- maxim,boost-mode : + In boost mode the device can produce up to 1.2A of total current + on both outputs. The maximum current on each output is reduced + to 625mA then. If not enabled explicitly, boost setting defaults to + LEDS_BOOST_FIXED in case both current sources are used. + Possible values: + LEDS_BOOST_OFF (0) - no boost, + LEDS_BOOST_ADAPTIVE (1) - adaptive mode, + LEDS_BOOST_FIXED (2) - fixed mode. +- maxim,boost-mvout : Output voltage of the boost module in millivolts. + Valid values: 3300 - 5500, step by 25 (rounded down) + Default: 3300 +- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired + if chip estimates that system voltage could drop below this level due + to flash power consumption. + Valid values: 2400 - 3400, step by 33 (rounded down) + Default: 2400 + +Required properties for the LED child node: +- led-sources : see Documentation/devicetree/bindings/leds/common.txt; + device current output identifiers: 0 - FLED1, 1 - FLED2 +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + Valid values for a LED connected to one FLED output: + 15625 - 250000, step by 15625 (rounded down) + Valid values for a LED connected to both FLED outputs: + 15625 - 500000, step by 15625 (rounded down) +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + Valid values for a single LED connected to one FLED output + (boost mode must be turned off): + 15625 - 1000000, step by 15625 (rounded down) + Valid values for a single LED connected to both FLED outputs: + 15625 - 1250000, step by 15625 (rounded down) + Valid values for two LEDs case: + 15625 - 625000, step by 15625 (rounded down) +- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt + Valid values: 62500 - 1000000, step by 62500 (rounded down) + +Optional properties for the LED child node: +- label : see Documentation/devicetree/bindings/leds/common.txt + Example: +#include <dt-bindings/leds/common.h> + max77693@66 { compatible = "maxim,max77693"; reg = <0x66>; @@ -117,5 +170,19 @@ Example: maxim,thermal-regulation-celsius = <75>; maxim,battery-overcurrent-microamp = <3000000>; maxim,charge-input-threshold-microvolt = <4300000>; + + led { + compatible = "maxim,max77693-led"; + maxim,boost-mode = <LEDS_BOOST_FIXED>; + maxim,boost-mvout = <5000>; + maxim,mvsys-min = <2400>; + + camera_flash: flash-led { + label = "max77693-flash"; + led-sources = <0>, <1>; + led-max-microamp = <500000>; + flash-max-microamp = <1250000>; + flash-max-timeout-us = <1000000>; + }; }; }; diff --git a/kernel/Documentation/devicetree/bindings/mfd/max77802.txt b/kernel/Documentation/devicetree/bindings/mfd/max77802.txt new file mode 100644 index 000000000..51fc1a60c --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/mfd/max77802.txt @@ -0,0 +1,26 @@ +Maxim MAX77802 multi-function device + +The Maxim MAX77802 is a Power Management IC (PMIC) that contains 10 high +efficiency Buck regulators, 32 Low-DropOut (LDO) regulators used to power +up application processors and peripherals, a 2-channel 32kHz clock outputs, +a Real-Time-Clock (RTC) and a I2C interface to program the individual +regulators, clocks outputs and the RTC. + +Bindings for the built-in 32k clock generator block and +regulators are defined in ../clk/maxim,max77802.txt and +../regulator/max77802.txt respectively. + +Required properties: +- compatible : Must be "maxim,max77802" +- reg : Specifies the I2C slave address of PMIC block. +- interrupts : I2C device IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Example: + + max77802: pmic@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&intc>; + interrupts = <26 IRQ_TYPE_NONE>; + reg = <0x09>; + }; diff --git a/kernel/Documentation/devicetree/bindings/mfd/mfd.txt b/kernel/Documentation/devicetree/bindings/mfd/mfd.txt new file mode 100644 index 000000000..af9d6931a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/mfd/mfd.txt @@ -0,0 +1,41 @@ +Multi-Function Devices (MFD) + +These devices comprise a nexus for heterogeneous hardware blocks containing +more than one non-unique yet varying hardware functionality. + +A typical MFD can be: + +- A mixed signal ASIC on an external bus, sometimes a PMIC (Power Management + Integrated Circuit) that is manufactured in a lower technology node (rough + silicon) that handles analog drivers for things like audio amplifiers, LED + drivers, level shifters, PHY (physical interfaces to things like USB or + ethernet), regulators etc. + +- A range of memory registers containing "miscellaneous system registers" also + known as a system controller "syscon" or any other memory range containing a + mix of unrelated hardware devices. + +Optional properties: + +- compatible : "simple-mfd" - this signifies that the operating system should + consider all subnodes of the MFD device as separate devices akin to how + "simple-bus" inidicates when to see subnodes as children for a simple + memory-mapped bus. For more complex devices, when the nexus driver has to + probe registers to figure out what child devices exist etc, this should not + be used. In the latter case the child devices will be determined by the + operating system. + +Example: + +foo@1000 { + compatible = "syscon", "simple-mfd"; + reg = <0x01000 0x1000>; + + led@08.0 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x01>; + label = "myled"; + default-state = "on"; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/mfd/rk808.txt b/kernel/Documentation/devicetree/bindings/mfd/rk808.txt index 9e6e2592e..4ca6aab42 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/rk808.txt @@ -24,6 +24,10 @@ Optional properties: - vcc10-supply: The input supply for LDO_REG6 - vcc11-supply: The input supply for LDO_REG8 - vcc12-supply: The input supply for SWITCH_REG2 +- dvs-gpios: buck1/2 can be controlled by gpio dvs, this is GPIO specifiers + for 2 host gpio's used for dvs. The format of the gpio specifier depends in + the gpio controller. If DVS GPIOs aren't present, voltage changes will happen + very quickly with no slow ramp time. Regulators: All the regulators of RK808 to be instantiated shall be listed in a child node named 'regulators'. Each regulator is represented @@ -55,7 +59,9 @@ Example: interrupt-parent = <&gpio0>; interrupts = <4 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; - pinctrl-0 = <&pmic_int>; + pinctrl-0 = <&pmic_int &dvs_1 &dvs_2>; + dvs-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>, + <&gpio7 15 GPIO_ACTIVE_HIGH>; reg = <0x1b>; rockchip,system-power-controller; wakeup-source; diff --git a/kernel/Documentation/devicetree/bindings/mfd/s2mps11.txt b/kernel/Documentation/devicetree/bindings/mfd/s2mps11.txt index 57a045016..09b94c97f 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,5 +1,5 @@ -* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator +* Samsung S2MPS11/13/14/15 and S2MPU02 Voltage and Current Regulator The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is @@ -7,17 +7,28 @@ interfaced to the host controller using an I2C interface. Each sub-block is addressed by the host system using different I2C slave addresses. Required properties: -- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" - or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". +- compatible: Should be one of the following + - "samsung,s2mps11-pmic" + - "samsung,s2mps13-pmic" + - "samsung,s2mps14-pmic" + - "samsung,s2mps15-pmic" + - "samsung,s2mpu02-pmic". - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. Optional properties: - interrupt-parent: Specifies the phandle of the interrupt controller to which the interrupts from s2mps11 are delivered to. - interrupts: Interrupt specifiers for interrupt sources. +- samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled + down. When the system is suspended it will always go down thus triggerring + unwanted buck warm reset (setting buck voltages to default values). +- samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is + connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 + register to turn off the power. Usually the ACOKB is pulled up to VBATT so + when PWRHOLD pin goes low, the rising ACOKB will trigger power off. Optional nodes: -- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 +- clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768 KHz outputs, so to register these as clocks with common clock framework instantiate a sub-node named "clocks". It uses the common clock binding documented in : @@ -30,12 +41,13 @@ Optional nodes: the clock which they consume. Clock ID Devices ---------------------------------------------------------- - 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 - 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 - 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 + 32KhzCP 1 S2MPS11, S2MPS13, S2MPS15, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", "samsung,s2mps14-clk", "samsung,s5m8767-clk" + The s2msp15 uses the same compatible as s2mps13, as both provides similar clocks. - regulators: The regulators of s2mps11 that have to be instantiated should be included in a sub-node named 'regulators'. Regulator nodes included in this @@ -83,6 +95,7 @@ as per the datasheet of s2mps11. - S2MPS11: 1 to 38 - S2MPS13: 1 to 40 - S2MPS14: 1 to 25 + - S2MPS15: 1 to 27 - S2MPU02: 1 to 28 - Example: LDO1, LDO2, LDO28 - BUCKn @@ -90,6 +103,7 @@ as per the datasheet of s2mps11. - S2MPS11: 1 to 10 - S2MPS13: 1 to 10 - S2MPS14: 1 to 5 + - S2MPS15: 1 to 10 - S2MPU02: 1 to 7 - Example: BUCK1, BUCK2, BUCK9 diff --git a/kernel/Documentation/devicetree/bindings/mfd/sky81452.txt b/kernel/Documentation/devicetree/bindings/mfd/sky81452.txt index 35181794a..511764acd 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/sky81452.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/sky81452.txt @@ -6,7 +6,7 @@ Required properties: Required child nodes: - backlight : container node for backlight following the binding - in video/backlight/sky81452-backlight.txt + in leds/backlight/sky81452-backlight.txt - regulator : container node for regulators following the binding in regulator/sky81452-regulator.txt diff --git a/kernel/Documentation/devicetree/bindings/mfd/tc3589x.txt b/kernel/Documentation/devicetree/bindings/mfd/tc3589x.txt index 6fcedba46..23fc2f21f 100644 --- a/kernel/Documentation/devicetree/bindings/mfd/tc3589x.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/tc3589x.txt @@ -55,7 +55,8 @@ Optional nodes: - linux,keymap: the definition can be found in bindings/input/matrix-keymap.txt - linux,no-autorepeat: do no enable autorepeat feature. - - linux,wakeup: use any event on keypad as wakeup event. + - wakeup-source: use any event on keypad as wakeup event. + (Legacy property supported: "linux,wakeup") Example: @@ -84,7 +85,6 @@ tc35893@44 { keypad,num-columns = <8>; keypad,num-rows = <8>; linux,no-autorepeat; - linux,wakeup; linux,keymap = <0x0301006b 0x04010066 0x06040072 @@ -103,5 +103,6 @@ tc35893@44 { 0x01030039 0x07060069 0x050500d9>; + wakeup-source; }; }; diff --git a/kernel/Documentation/devicetree/bindings/mfd/tps6507x.txt b/kernel/Documentation/devicetree/bindings/mfd/tps6507x.txt index 8fffa3c5e..8fffa3c5e 100755..100644 --- a/kernel/Documentation/devicetree/bindings/mfd/tps6507x.txt +++ b/kernel/Documentation/devicetree/bindings/mfd/tps6507x.txt |