summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/devicetree/bindings/memory-controllers
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/memory-controllers')
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt79
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt75
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt178
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt21
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt36
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt44
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/synopsys.txt11
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt210
-rw-r--r--kernel/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt55
9 files changed, 709 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt
new file mode 100644
index 000000000..d5e370450
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt
@@ -0,0 +1,79 @@
+Integrated Flash Controller
+
+Properties:
+- name : Should be ifc
+- compatible : should contain "fsl,ifc". The version of the integrated
+ flash controller can be found in the IFC_REV register at
+ offset zero.
+
+- #address-cells : Should be either two or three. The first cell is the
+ chipselect number, and the remaining cells are the
+ offset into the chipselect.
+- #size-cells : Either one or two, depending on how large each chipselect
+ can be.
+- reg : Offset and length of the register set for the device
+- interrupts: IFC may have one or two interrupts. If two interrupt
+ specifiers are present, the first is the "common"
+ interrupt (CM_EVTER_STAT), and the second is the NAND
+ interrupt (NAND_EVTER_STAT). If there is only one,
+ that interrupt reports both types of event.
+
+
+- ranges : Each range corresponds to a single chipselect, and covers
+ the entire access window as configured.
+
+Child device nodes describe the devices connected to IFC such as NOR (e.g.
+cfi-flash) and NAND (fsl,ifc-nand). There might be board specific devices
+like FPGAs, CPLDs, etc.
+
+Example:
+
+ ifc@ffe1e000 {
+ compatible = "fsl,ifc", "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0x0 0xffe1e000 0 0x2000>;
+ interrupts = <16 2 19 2>;
+
+ /* NOR, NAND Flashes and CPLD on board */
+ ranges = <0x0 0x0 0x0 0xee000000 0x02000000
+ 0x1 0x0 0x0 0xffa00000 0x00010000
+ 0x3 0x0 0x0 0xffb00000 0x00020000>;
+
+ flash@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x2000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@0 {
+ /* 32MB for user data */
+ reg = <0x0 0x02000000>;
+ label = "NOR Data";
+ };
+ };
+
+ flash@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x1 0x0 0x10000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND U-Boot Image";
+ read-only;
+ };
+ };
+
+ cpld@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1010rdb-cpld";
+ reg = <0x3 0x0 0x000001f>;
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt
new file mode 100644
index 000000000..f936b5589
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt
@@ -0,0 +1,75 @@
+* Ingenic JZ4780 NAND/external memory controller (NEMC)
+
+This file documents the device tree bindings for the NEMC external memory
+controller in Ingenic JZ4780
+
+Required properties:
+- compatible: Should be set to one of:
+ "ingenic,jz4780-nemc" (JZ4780)
+- reg: Should specify the NEMC controller registers location and length.
+- clocks: Clock for the NEMC controller.
+- #address-cells: Must be set to 2.
+- #size-cells: Must be set to 1.
+- ranges: A set of ranges for each bank describing the physical memory layout.
+ Each should specify the following 4 integer values:
+
+ <cs number> 0 <physical address of mapping> <size of mapping>
+
+Each child of the NEMC node describes a device connected to the NEMC.
+
+Required child node properties:
+- reg: Should contain at least one register specifier, given in the following
+ format:
+
+ <cs number> <offset> <size>
+
+ Multiple registers can be specified across multiple banks. This is needed,
+ for example, for packaged NAND devices with multiple dies. Such devices
+ should be grouped into a single node.
+
+Optional child node properties:
+- ingenic,nemc-bus-width: Specifies the bus width in bits. Defaults to 8 bits.
+- ingenic,nemc-tAS: Address setup time in nanoseconds.
+- ingenic,nemc-tAH: Address hold time in nanoseconds.
+- ingenic,nemc-tBP: Burst pitch time in nanoseconds.
+- ingenic,nemc-tAW: Access wait time in nanoseconds.
+- ingenic,nemc-tSTRV: Static memory recovery time in nanoseconds.
+
+If a child node references multiple banks in its "reg" property, the same value
+for all optional parameters will be configured for all banks. If any optional
+parameters are omitted, they will be left unchanged from whatever they are
+configured to when the NEMC device is probed (which may be the reset value as
+given in the hardware reference manual, or a value configured by the boot
+loader).
+
+Example (NEMC node with a NAND child device attached at CS1):
+
+nemc: nemc@13410000 {
+ compatible = "ingenic,jz4780-nemc";
+ reg = <0x13410000 0x10000>;
+
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ ranges = <1 0 0x1b000000 0x1000000
+ 2 0 0x1a000000 0x1000000
+ 3 0 0x19000000 0x1000000
+ 4 0 0x18000000 0x1000000
+ 5 0 0x17000000 0x1000000
+ 6 0 0x16000000 0x1000000>;
+
+ clocks = <&cgu JZ4780_CLK_NEMC>;
+
+ nand: nand@1 {
+ compatible = "ingenic,jz4780-nand";
+ reg = <1 0 0x1000000>;
+
+ ingenic,nemc-tAS = <10>;
+ ingenic,nemc-tAH = <5>;
+ ingenic,nemc-tBP = <10>;
+ ingenic,nemc-tAW = <15>;
+ ingenic,nemc-tSTRV = <100>;
+
+ ...
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt
new file mode 100644
index 000000000..1ee3bc09f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt
@@ -0,0 +1,178 @@
+Device tree bindings for MVEBU Device Bus controllers
+
+The Device Bus controller available in some Marvell's SoC allows to control
+different types of standard memory and I/O devices such as NOR, NAND, and FPGA.
+The actual devices are instantiated from the child nodes of a Device Bus node.
+
+Required properties:
+
+ - compatible: Armada 370/XP SoC are supported using the
+ "marvell,mvebu-devbus" compatible string.
+
+ Orion5x SoC are supported using the
+ "marvell,orion-devbus" compatible string.
+
+ - reg: A resource specifier for the register space.
+ This is the base address of a chip select within
+ the controller's register space.
+ (see the example below)
+
+ - #address-cells: Must be set to 1
+ - #size-cells: Must be set to 1
+ - ranges: Must be set up to reflect the memory layout with four
+ integer values for each chip-select line in use:
+ 0 <physical address of mapping> <size>
+
+Optional properties:
+
+ - devbus,keep-config This property can optionally be used to keep
+ using the timing parameters set by the
+ bootloader. It makes all the timing properties
+ described below unused.
+
+Timing properties for child nodes:
+
+Read parameters:
+
+ - devbus,turn-off-ps: Defines the time during which the controller does not
+ drive the AD bus after the completion of a device read.
+ This prevents contentions on the Device Bus after a read
+ cycle from a slow device.
+ Mandatory, except if devbus,keep-config is used.
+
+ - devbus,bus-width: Defines the bus width, in bits (e.g. <16>).
+ Mandatory, except if devbus,keep-config is used.
+
+ - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle,
+ to read data sample. This parameter is useful for
+ synchronous pipelined devices, where the address
+ precedes the read data by one or two cycles.
+ Mandatory, except if devbus,keep-config is used.
+
+ - devbus,acc-first-ps: Defines the time delay from the negation of
+ ALE[0] to the cycle that the first read data is sampled
+ by the controller.
+ Mandatory, except if devbus,keep-config is used.
+
+ - devbus,acc-next-ps: Defines the time delay between the cycle that
+ samples data N and the cycle that samples data N+1
+ (in burst accesses).
+ Mandatory, except if devbus,keep-config is used.
+
+ - devbus,rd-setup-ps: Defines the time delay between DEV_CSn assertion to
+ DEV_OEn assertion. If set to 0 (default),
+ DEV_OEn and DEV_CSn are asserted at the same cycle.
+ This parameter has no affect on <acc-first-ps> parameter
+ (no affect on first data sample). Set <rd-setup-ps>
+ to a value smaller than <acc-first-ps>.
+ Mandatory for "marvell,mvebu-devbus" compatible string,
+ except if devbus,keep-config is used.
+
+ - devbus,rd-hold-ps: Defines the time between the last data sample to the
+ de-assertion of DEV_CSn. If set to 0 (default),
+ DEV_OEn and DEV_CSn are de-asserted at the same cycle
+ (the cycle of the last data sample).
+ This parameter has no affect on DEV_OEn de-assertion.
+ DEV_OEn is always de-asserted the next cycle after
+ last data sampled. Also this parameter has no
+ affect on <turn-off-ps> parameter.
+ Set <rd-hold-ps> to a value smaller than <turn-off-ps>.
+ Mandatory for "marvell,mvebu-devbus" compatible string,
+ except if devbus,keep-config is used.
+
+Write parameters:
+
+ - devbus,ale-wr-ps: Defines the time delay from the ALE[0] negation cycle
+ to the DEV_WEn assertion.
+ Mandatory.
+
+ - devbus,wr-low-ps: Defines the time during which DEV_WEn is active.
+ A[2:0] and Data are kept valid as long as DEV_WEn
+ is active. This parameter defines the setup time of
+ address and data to DEV_WEn rise.
+ Mandatory.
+
+ - devbus,wr-high-ps: Defines the time during which DEV_WEn is kept
+ inactive (high) between data beats of a burst write.
+ DEV_A[2:0] and Data are kept valid (do not toggle) for
+ <wr-high-ps> - <tick> ps.
+ This parameter defines the hold time of address and
+ data after DEV_WEn rise.
+ Mandatory.
+
+ - devbus,sync-enable: Synchronous device enable.
+ 1: True
+ 0: False
+ Mandatory for "marvell,mvebu-devbus" compatible string,
+ except if devbus,keep-config is used.
+
+An example for an Armada XP GP board, with a 16 MiB NOR device as child
+is showed below. Note that the Device Bus driver is in charge of allocating
+the mbus address decoding window for each of its child devices.
+The window is created using the chip select specified in the child
+device node together with the base address and size specified in the ranges
+property. For instance, in the example below the allocated decoding window
+will start at base address 0xf0000000, with a size 0x1000000 (16 MiB)
+for chip select 0 (a.k.a DEV_BOOTCS).
+
+This address window handling is done in this mvebu-devbus only as a temporary
+solution. It will be removed when the support for mbus device tree binding is
+added.
+
+The reg property implicitly specifies the chip select as this:
+
+ 0x10400: DEV_BOOTCS
+ 0x10408: DEV_CS0
+ 0x10410: DEV_CS1
+ 0x10418: DEV_CS2
+ 0x10420: DEV_CS3
+
+Example:
+
+ devbus-bootcs@d0010400 {
+ status = "okay";
+ ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf0000000, size 0x1000000 */
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <8>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ flash@0 {
+ compatible = "cfi-flash";
+
+ /* 16 MiB */
+ reg = <0 0x1000000>;
+ bank-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * We split the 16 MiB in two partitions,
+ * just as an example.
+ */
+ partition@0 {
+ label = "First";
+ reg = <0 0x800000>;
+ };
+
+ partition@800000 {
+ label = "Second";
+ reg = <0x800000 0x800000>;
+ };
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt
new file mode 100644
index 000000000..89657d1d4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt
@@ -0,0 +1,21 @@
+Device Tree bindings for MVEBU SDRAM controllers
+
+The Marvell EBU SoCs all have a SDRAM controller. The SDRAM controller
+differs from one SoC variant to another, but they also share a number
+of commonalities.
+
+For now, this Device Tree binding documentation only documents the
+Armada XP SDRAM controller.
+
+Required properties:
+
+ - compatible: for Armada XP, "marvell,armada-xp-sdram-controller"
+ - reg: a resource specifier for the register space, which should
+ include all SDRAM controller registers as per the datasheet.
+
+Example:
+
+sdramc@1400 {
+ compatible = "marvell,armada-xp-sdram-controller";
+ reg = <0x1400 0x500>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt
new file mode 100644
index 000000000..f3db93c85
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt
@@ -0,0 +1,36 @@
+NVIDIA Tegra Memory Controller device tree bindings
+===================================================
+
+Required properties:
+- compatible: Should be "nvidia,tegra<chip>-mc"
+- reg: Physical base address and length of the controller's registers.
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - mc: the module's clock input
+- interrupts: The interrupt outputs from the controller.
+- #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines
+ the SWGROUP of the master.
+
+This device implements an IOMMU that complies with the generic IOMMU binding.
+See ../iommu/iommu.txt for details.
+
+Example:
+--------
+
+ mc: memory-controller@0,70019000 {
+ compatible = "nvidia,tegra124-mc";
+ reg = <0x0 0x70019000 0x0 0x1000>;
+ clocks = <&tegra_car TEGRA124_CLK_MC>;
+ clock-names = "mc";
+
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+
+ #iommu-cells = <1>;
+ };
+
+ sdhci@0,700b0000 {
+ compatible = "nvidia,tegra124-sdhci";
+ ...
+ iommus = <&mc TEGRA_SWGROUP_SDMMC1A>;
+ };
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt
new file mode 100644
index 000000000..c64b7925c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt
@@ -0,0 +1,44 @@
+DT bindings for Renesas R-Mobile and SH-Mobile memory controllers
+=================================================================
+
+Renesas R-Mobile and SH-Mobile SoCs contain one or more memory controllers.
+These memory controllers differ from one SoC variant to another, and are called
+by different names ("DDR Bus Controller (DBSC)", "DDR3 Bus State Controller
+(DBSC3)", "SDRAM Bus State Controller (SBSC)").
+
+Currently memory controller device nodes are used only to reference PM
+domains, and prevent these PM domains from being powered down, which would
+crash the system.
+
+As there exist no actual drivers for these controllers yet, these bindings
+should be considered EXPERIMENTAL for now.
+
+Required properties:
+ - compatible: Must be one of the following SoC-specific values:
+ - "renesas,dbsc-r8a73a4" (R-Mobile APE6)
+ - "renesas,dbsc3-r8a7740" (R-Mobile A1)
+ - "renesas,sbsc-sh73a0" (SH-Mobile AG5)
+ - reg: Must contain the base address and length of the memory controller's
+ registers.
+
+Optional properties:
+ - interrupts: Must contain a list of interrupt specifiers for memory
+ controller interrupts, if available.
+ - interrupts-names: Must contain a list of interrupt names corresponding to
+ the interrupts in the interrupts property, if available.
+ Valid interrupt names are:
+ - "sec" (secure interrupt)
+ - "temp" (normal (temperature) interrupt)
+ - power-domains: Must contain a reference to the PM domain that the memory
+ controller belongs to, if available.
+
+Example:
+
+ sbsc1: memory-controller@fe400000 {
+ compatible = "renesas,sbsc-sh73a0";
+ reg = <0xfe400000 0x400>;
+ interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>,
+ <0 36 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "sec", "temp";
+ power-domains = <&pd_a4bc0>;
+ };
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/synopsys.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/synopsys.txt
new file mode 100644
index 000000000..f9c645414
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/synopsys.txt
@@ -0,0 +1,11 @@
+Binding for Synopsys IntelliDDR Multi Protocol Memory Controller
+
+Required properties:
+ - compatible: Should be 'xlnx,zynq-ddrc-a05'
+ - reg: Base address and size of the controllers memory area
+
+Example:
+ memory-controller@f8006000 {
+ compatible = "xlnx,zynq-ddrc-a05";
+ reg = <0xf8006000 0x1000>;
+ };
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
new file mode 100644
index 000000000..9592717f4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
@@ -0,0 +1,210 @@
+* Device tree bindings for Texas instruments AEMIF controller
+
+The Async External Memory Interface (EMIF16/AEMIF) controller is intended to
+provide a glue-less interface to a variety of asynchronous memory devices like
+ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories
+can be accessed at any given time via four chip selects with 64M byte access
+per chip select. Synchronous memories such as DDR1 SD RAM, SDR SDRAM
+and Mobile SDR are not supported.
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
+OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
+Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
+
+Required properties:
+
+- compatible: "ti,davinci-aemif"
+ "ti,keystone-aemif"
+ "ti,da850-aemif"
+
+- reg: contains offset/length value for AEMIF control registers
+ space.
+
+- #address-cells: Must be 2. The partition number has to be encoded in the
+ first address cell and it may accept values 0..N-1
+ (N - total number of partitions). It's recommended to
+ assign N-1 number for the control partition. The second
+ cell is the offset into the partition.
+
+- #size-cells: Must be set to 1.
+
+- ranges: Contains memory regions. There are two types of
+ ranges/partitions:
+ - CS-specific partition/range. If continuous, must be
+ set up to reflect the memory layout for 4 chipselects,
+ if not then additional range/partition can be added and
+ child device can select the proper one.
+ - control partition which is common for all CS
+ interfaces.
+
+- clocks: the clock feeding the controller clock. Required only
+ if clock tree data present in device tree.
+ See clock-bindings.txt
+
+- clock-names: clock name. It has to be "aemif". Required only if clock
+ tree data present in device tree, in another case don't
+ use it.
+ See clock-bindings.txt
+
+- clock-ranges: Empty property indicating that child nodes can inherit
+ named clocks. Required only if clock tree data present
+ in device tree.
+ See clock-bindings.txt
+
+
+Child chip-select (cs) nodes contain the memory devices nodes connected to
+such as NOR (e.g. cfi-flash) and NAND (ti,davinci-nand, see davinci-nand.txt).
+There might be board specific devices like FPGAs.
+
+Required child cs node properties:
+
+- #address-cells: Must be 2.
+
+- #size-cells: Must be 1.
+
+- ranges: Empty property indicating that child nodes can inherit
+ memory layout.
+
+- clock-ranges: Empty property indicating that child nodes can inherit
+ named clocks. Required only if clock tree data present
+ in device tree.
+
+- ti,cs-chipselect: number of chipselect. Indicates on the aemif driver
+ which chipselect is used for accessing the memory. For
+ compatibles "ti,davinci-aemif" and "ti,keystone-aemif"
+ it can be in range [0-3]. For compatible
+ "ti,da850-aemif" range is [2-5].
+
+Optional child cs node properties:
+
+- ti,cs-bus-width: width of the asynchronous device's data bus
+ 8 or 16 if not preset 8
+
+- ti,cs-select-strobe-mode: enable/disable select strobe mode
+ In select strobe mode chip select behaves as
+ the strobe and is active only during the strobe
+ period. If present then enable.
+
+- ti,cs-extended-wait-mode: enable/disable extended wait mode
+ if set, the controller monitors the EMIFWAIT pin
+ mapped to that chip select to determine if the
+ device wants to extend the strobe period. If
+ present then enable.
+
+- ti,cs-min-turnaround-ns: minimum turn around time, ns
+ Time between the end of one asynchronous memory
+ access and the start of another asynchronous
+ memory access. This delay is not incurred
+ between a read followed by read or a write
+ followed by a write to same chip select.
+
+- ti,cs-read-setup-ns: read setup width, ns
+ Time between the beginning of a memory cycle
+ and the activation of read strobe.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-read-strobe-ns: read strobe width, ns
+ Time between the activation and deactivation of
+ the read strobe.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-read-hold-ns: read hold width, ns
+ Time between the deactivation of the read
+ strobe and the end of the cycle (which may be
+ either an address change or the deactivation of
+ the chip select signal.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-setup-ns: write setup width, ns
+ Time between the beginning of a memory cycle
+ and the activation of write strobe.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-strobe-ns: write strobe width, ns
+ Time between the activation and deactivation of
+ the write strobe.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-hold-ns: write hold width, ns
+ Time between the deactivation of the write
+ strobe and the end of the cycle (which may be
+ either an address change or the deactivation of
+ the chip select signal.
+ Minimum value is 1 (0 treated as 1).
+
+If any of the above parameters are absent, current parameter value will be taken
+from the corresponding HW reg.
+
+Example for aemif, davinci nand and nor flash chip select shown below.
+
+memory-controller@21000A00 {
+ compatible = "ti,davinci-aemif";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clocks = <&clkaemif 0>;
+ clock-names = "aemif";
+ clock-ranges;
+ reg = <0x21000A00 0x00000100>;
+ ranges = <0 0 0x70000000 0x10000000
+ 1 0 0x21000A00 0x00000100>;
+ /*
+ * Partition0: CS-specific memory range which is
+ * implemented as continuous physical memory region
+ * Partition1: control memory range
+ */
+
+ nand:cs2 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-ranges;
+ ranges;
+
+ ti,cs-chipselect = <2>;
+ /* all timings in nanoseconds */
+ ti,cs-min-turnaround-ns = <0>;
+ ti,cs-read-hold-ns = <7>;
+ ti,cs-read-strobe-ns = <42>;
+ ti,cs-read-setup-ns = <14>;
+ ti,cs-write-hold-ns = <7>;
+ ti,cs-write-strobe-ns = <42>;
+ ti,cs-write-setup-ns = <14>;
+
+ nand@0,0x8000000 {
+ compatible = "ti,davinci-nand";
+ reg = <0 0x8000000 0x4000000
+ 1 0x0000000 0x0000100>;
+ /*
+ * Partition0, offset 0x8000000, size 0x4000000
+ * Partition1, offset 0x0000000, size 0x0000100
+ */
+
+ .. see davinci-nand.txt
+ };
+ };
+
+ nor:cs0 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-ranges;
+ ranges;
+
+ ti,cs-chipselect = <0>;
+ /* all timings in nanoseconds */
+ ti,cs-min-turnaround-ns = <0>;
+ ti,cs-read-hold-ns = <8>;
+ ti,cs-read-strobe-ns = <40>;
+ ti,cs-read-setup-ns = <14>;
+ ti,cs-write-hold-ns = <7>;
+ ti,cs-write-strobe-ns = <40>;
+ ti,cs-write-setup-ns = <14>;
+ ti,cs-bus-width = <16>;
+
+ flash@0,0x0000000 {
+ compatible = "cfi-flash";
+ reg = <0 0x0000000 0x4000000>;
+
+ ...
+ };
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
new file mode 100644
index 000000000..938f8e1ba
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
@@ -0,0 +1,55 @@
+* EMIF family of TI SDRAM controllers
+
+EMIF - External Memory Interface - is an SDRAM controller used in
+TI SoCs. EMIF supports, based on the IP revision, one or more of
+DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance
+of the EMIF IP and memory parts attached to it.
+
+Required properties:
+- compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev>
+ is the IP revision of the specific EMIF instance.
+
+- phy-type : <u32> indicating the DDR phy type. Following are the
+ allowed values
+ <1> : Attila PHY
+ <2> : Intelli PHY
+
+- device-handle : phandle to a "lpddr2" node representing the memory part
+
+- ti,hwmods : For TI hwmods processing and omap device creation
+ the value shall be "emif<n>" where <n> is the number of the EMIF
+ instance with base 1.
+
+Optional properties:
+- cs1-used : Have this property if CS1 of this EMIF
+ instance has a memory part attached to it. If there is a memory
+ part attached to CS1, it should be the same type as the one on CS0,
+ so there is no need to give the details of this memory part.
+
+- cal-resistor-per-cs : Have this property if the board has one
+ calibration resistor per chip-select.
+
+- hw-caps-read-idle-ctrl: Have this property if the controller
+ supports read idle window programming
+
+- hw-caps-dll-calib-ctrl: Have this property if the controller
+ supports dll calibration control
+
+- hw-caps-ll-interface : Have this property if the controller
+ has a low latency interface and corresponding interrupt events
+
+- hw-caps-temp-alert : Have this property if the controller
+ has capability for generating SDRAM temperature alerts
+
+Example:
+
+emif1: emif@0x4c000000 {
+ compatible = "ti,emif-4d";
+ ti,hwmods = "emif2";
+ phy-type = <1>;
+ device-handle = <&elpida_ECB240ABACN>;
+ cs1-used;
+ hw-caps-read-idle-ctrl;
+ hw-caps-ll-interface;
+ hw-caps-temp-alert;
+};