diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/leds')
17 files changed, 977 insertions, 13 deletions
diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt new file mode 100644 index 000000000..261df2799 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt @@ -0,0 +1,15 @@ +88pm860x-backlight bindings + +Optional properties: + - marvell,88pm860x-iset: Current supplies on backlight device. + - marvell,88pm860x-pwm: PWM frequency on backlight device. + +Example: + + backlights { + backlight-0 { + marvell,88pm860x-iset = <4>; + marvell,88pm860x-pwm = <3>; + }; + backlight-2 { + }; diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt new file mode 100644 index 000000000..321be6640 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt @@ -0,0 +1,16 @@ +gpio-backlight bindings + +Required properties: + - compatible: "gpio-backlight" + - gpios: describes the gpio that is used for enabling/disabling the backlight. + refer to bindings/gpio/gpio.txt for more details. + +Optional properties: + - default-on: enable the backlight at boot. + +Example: + backlight { + compatible = "gpio-backlight"; + gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; + default-on; + }; diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/lp855x.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/lp855x.txt new file mode 100644 index 000000000..0a3ecbc3a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/backlight/lp855x.txt @@ -0,0 +1,70 @@ +lp855x bindings + +Required properties: + - compatible: "ti,lp8550", "ti,lp8551", "ti,lp8552", "ti,lp8553", + "ti,lp8555", "ti,lp8556", "ti,lp8557" + - reg: I2C slave address (u8) + - dev-ctrl: Value of DEVICE CONTROL register (u8). It depends on the device. + +Optional properties: + - bl-name: Backlight device name (string) + - init-brt: Initial value of backlight brightness (u8) + - pwm-period: PWM period value. Set only PWM input mode used (u32) + - rom-addr: Register address of ROM area to be updated (u8) + - rom-val: Register value to be updated (u8) + - power-supply: Regulator which controls the 3V rail + +Example: + + /* LP8555 */ + backlight@2c { + compatible = "ti,lp8555"; + reg = <0x2c>; + + dev-ctrl = /bits/ 8 <0x00>; + pwm-period = <10000>; + + /* 4V OV, 4 output LED0 string enabled */ + rom_14h { + rom-addr = /bits/ 8 <0x14>; + rom-val = /bits/ 8 <0xcf>; + }; + + /* Heavy smoothing, 24ms ramp time step */ + rom_15h { + rom-addr = /bits/ 8 <0x15>; + rom-val = /bits/ 8 <0xc7>; + }; + + /* 4 output LED1 string enabled */ + rom_19h { + rom-addr = /bits/ 8 <0x19>; + rom-val = /bits/ 8 <0x0f>; + }; + }; + + /* LP8556 */ + backlight@2c { + compatible = "ti,lp8556"; + reg = <0x2c>; + + bl-name = "lcd-bl"; + dev-ctrl = /bits/ 8 <0x85>; + init-brt = /bits/ 8 <0x10>; + }; + + /* LP8557 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + power-supply = <&backlight_vdd>; + + dev-ctrl = /bits/ 8 <0x41>; + init-brt = /bits/ 8 <0x0a>; + + /* 4V OV, 4 output LED string enabled */ + rom_14h { + rom-addr = /bits/ 8 <0x14>; + rom-val = /bits/ 8 <0xcf>; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt new file mode 100644 index 000000000..b4cffdaa4 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt @@ -0,0 +1,10 @@ +88pm860x-backlight bindings + +Optional properties: + - maxim,max8925-dual-string: whether support dual string + +Example: + + backlights { + maxim,max8925-dual-string = <0>; + }; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-pm8941-wled.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt index a85a964d6..e5b294daf 100644 --- a/kernel/Documentation/devicetree/bindings/leds/leds-pm8941-wled.txt +++ b/kernel/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt @@ -5,10 +5,9 @@ Required properties: - reg: slave address Optional properties: -- label: The label for this led - See Documentation/devicetree/bindings/leds/common.txt -- linux,default-trigger: Default trigger assigned to the LED - See Documentation/devicetree/bindings/leds/common.txt +- default-brightness: brightness value on boot, value from: 0-4095 + default: 2048 +- label: The name of the backlight device - qcom,cs-out: bool; enable current sink output - qcom,cabc: bool; enable content adaptive backlight control - qcom,ext-gen: bool; use externally generated modulator signal to dim diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt new file mode 100644 index 000000000..764db86d4 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt @@ -0,0 +1,35 @@ +pwm-backlight bindings + +Required properties: + - compatible: "pwm-backlight" + - pwms: OF device-tree PWM specification (see PWM binding[0]) + - brightness-levels: Array of distinct brightness levels. Typically these + are in the range from 0 to 255, but any range starting at 0 will do. + The actual brightness level (PWM duty cycle) will be interpolated + from these values. 0 means a 0% duty cycle (darkest/off), while the + last value in the array represents a 100% duty cycle (brightest). + - default-brightness-level: the default brightness level (index into the + array defined by the "brightness-levels" property) + - power-supply: regulator for supply voltage + +Optional properties: + - pwm-names: a list of names for the PWM devices specified in the + "pwms" property (see PWM binding[0]) + - enable-gpios: contains a single GPIO specifier for the GPIO which enables + and disables the backlight (see GPIO binding[1]) + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 5000000>; + + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + + power-supply = <&vdd_bl_reg>; + enable-gpios = <&gpio 58 0>; + }; diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt new file mode 100644 index 000000000..8bf2940f5 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt @@ -0,0 +1,29 @@ +SKY81452-backlight bindings + +Required properties: +- compatible : Must be "skyworks,sky81452-backlight" + +Optional properties: +- name : Name of backlight device. Default is 'lcd-backlight'. +- gpios : GPIO to use to EN pin. + See Documentation/devicetree/bindings/gpio/gpio.txt +- led-sources : List of enabled channels from 0 to 5. + See Documentation/devicetree/bindings/leds/common.txt +- skyworks,ignore-pwm : Ignore both PWM input +- skyworks,dpwm-mode : Enable DPWM dimming mode, otherwise Analog dimming. +- skyworks,phase-shift : Enable phase shift mode +- skyworks,short-detection-threshold-volt + : It should be one of 4, 5, 6 and 7V. +- skyworks,current-limit-mA + : It should be 2300mA or 2750mA. + +Example: + + backlight { + compatible = "skyworks,sky81452-backlight"; + name = "pwm-backlight"; + led-sources = <0 1 2 5>; + skyworks,ignore-pwm; + skyworks,phase-shift; + skyworks,current-limit-mA = <2300>; + }; diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt new file mode 100644 index 000000000..5fb9279ac --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt @@ -0,0 +1,27 @@ +TPS65217 family of regulators + +The TPS65217 chip contains a boost converter and current sinks which can be +used to drive LEDs for use as backlights. + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- backlight: node for specifying WLED1 and WLED2 lines in TPS65217 +- isel: selection bit, valid values: 1 for ISEL1 (low-level) and 2 for ISEL2 (high-level) +- fdim: PWM dimming frequency, valid values: 100, 200, 500, 1000 +- default-brightness: valid values: 0-100 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + reg = <0x24>; + compatible = "ti,tps65217"; + backlight { + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <100>; /* TPS65217_BL_FDIM_100HZ */ + default-brightness = <50>; + }; + }; + diff --git a/kernel/Documentation/devicetree/bindings/leds/common.txt b/kernel/Documentation/devicetree/bindings/leds/common.txt index 747c53805..68419843e 100644 --- a/kernel/Documentation/devicetree/bindings/leds/common.txt +++ b/kernel/Documentation/devicetree/bindings/leds/common.txt @@ -29,14 +29,23 @@ Optional properties for child nodes: "ide-disk" - LED indicates disk activity "timer" - LED flashes at a fixed, configurable rate -- max-microamp : maximum intensity in microamperes of the LED - (torch LED for flash devices) -- flash-max-microamp : maximum intensity in microamperes of the - flash LED; it is mandatory if the LED should - support the flash mode -- flash-timeout-us : timeout in microseconds after which the flash - LED is turned off +- led-max-microamp : Maximum LED supply current in microamperes. This property + can be made mandatory for the board configurations + introducing a risk of hardware damage in case an excessive + current is set. + For flash LED controllers with configurable current this + property is mandatory for the LEDs in the non-flash modes + (e.g. torch or indicator). +Required properties for flash LED child nodes: +- flash-max-microamp : Maximum flash LED supply current in microamperes. +- flash-max-timeout-us : Maximum timeout in microseconds after which the flash + LED is turned off. + +For controllers that have no configurable current the flash-max-microamp +property can be omitted. +For controllers that have no configurable timeout the flash-max-timeout-us +property can be omitted. Examples: @@ -49,7 +58,7 @@ system-status { camera-flash { label = "Flash"; led-sources = <0>, <1>; - max-microamp = <50000>; + led-max-microamp = <50000>; flash-max-microamp = <320000>; - flash-timeout-us = <500000>; + flash-max-timeout-us = <500000>; }; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/kernel/Documentation/devicetree/bindings/leds/leds-aat1290.txt new file mode 100644 index 000000000..85c0c5861 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/leds-aat1290.txt @@ -0,0 +1,73 @@ +* Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs + +The device is controlled through two pins: FL_EN and EN_SET. The pins when, +asserted high, enable flash strobe and movie mode (max 1/2 of flash current) +respectively. In order to add a capability of selecting the strobe signal source +(e.g. CPU or camera sensor) there is an additional switch required, independent +of the flash chip. The switch is controlled with pin control. + +Required properties: + +- compatible : Must be "skyworks,aat1290". +- flen-gpios : Must be device tree identifier of the flash device FL_EN pin. +- enset-gpios : Must be device tree identifier of the flash device EN_SET pin. + +Optional properties: +- pinctrl-names : Must contain entries: "default", "host", "isp". Entries + "default" and "host" must refer to the same pin configuration + node, which sets the host as a strobe signal provider. Entry + "isp" must refer to the pin configuration node, which sets the + ISP as a strobe signal provider. + +A discrete LED element connected to the device must be represented by a child +node - see Documentation/devicetree/bindings/leds/common.txt. + +Required properties of the LED child node: +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + Maximum flash LED supply current can be calculated using + following formula: I = 1A * 162kohm / Rset. +- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt + Maximum flash timeout can be calculated using following + formula: T = 8.82 * 10^9 * Ct. + +Optional properties of the LED child node: +- label : see Documentation/devicetree/bindings/leds/common.txt + +Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with +a switch that allows for routing strobe signal either from the host or from +the camera sensor): + +#include "exynos4412.dtsi" + +aat1290 { + compatible = "skyworks,aat1290"; + flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>; + enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default", "host", "isp"; + pinctrl-0 = <&camera_flash_host>; + pinctrl-1 = <&camera_flash_host>; + pinctrl-2 = <&camera_flash_isp>; + + camera_flash: flash-led { + label = "aat1290-flash"; + led-max-microamp = <520833>; + flash-max-microamp = <1012500>; + flash-max-timeout-us = <1940000>; + }; +}; + +&pinctrl_0 { + camera_flash_host: camera-flash-host { + samsung,pins = "gpj1-0"; + samsung,pin-function = <1>; + samsung,pin-val = <0>; + }; + + camera_flash_isp: camera-flash-isp { + samsung,pins = "gpj1-0"; + samsung,pin-function = <1>; + samsung,pin-val = <1>; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/kernel/Documentation/devicetree/bindings/leds/leds-bcm6328.txt new file mode 100644 index 000000000..3f48c1eaf --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/leds-bcm6328.txt @@ -0,0 +1,319 @@ +LEDs connected to Broadcom BCM6328 controller + +This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268. +In these SoCs it's possible to control LEDs both as GPIOs or by hardware. +However, on some devices there are Serial LEDs (LEDs connected to a 74x164 +controller), which can either be controlled by software (exporting the 74x164 +as spi-gpio. See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or +by hardware using this driver. +Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and +exporting the 74x164 as spi-gpio prevents those LEDs to be hardware +controlled, so the only chance to keep them working is by using this driver. + +BCM6328 LED controller has a HWDIS register, which controls whether a LED +should be controlled by a hardware signal instead of the MODE register value, +with 0 meaning hardware control enabled and 1 hardware control disabled. This +is usually 1:1 for hardware to LED signals, but through the activity/link +registers you have some limited control over rerouting the LEDs (as +explained later in brcm,link-signal-sources). Even if a LED is hardware +controlled you are still able to make it blink or light it up if it isn't, +but you can't turn it off if the hardware decides to light it up. For this +reason, hardware controlled LEDs aren't registered as LED class devices. + +Required properties: + - compatible : should be "brcm,bcm6328-leds". + - #address-cells : must be 1. + - #size-cells : must be 0. + - reg : BCM6328 LED controller address and size. + +Optional properties: + - brcm,serial-leds : Boolean, enables Serial LEDs. + Default : false + - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing. + Default : false + - brcm,serial-clk-low : Boolean, makes clock signal active low. + Default : false + - brcm,serial-dat-low : Boolean, makes data signal active low. + Default : false + - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction. + Default : false + +Each LED is represented as a sub-node of the brcm,bcm6328-leds device. + +LED sub-node required properties: + - reg : LED pin number (only LEDs 0 to 23 are valid). + +LED sub-node optional properties: + a) Optional properties for sub-nodes related to software controlled LEDs: + - label : see Documentation/devicetree/bindings/leds/common.txt + - active-low : Boolean, makes LED active low. + Default : false + - default-state : see + Documentation/devicetree/bindings/leds/leds-gpio.txt + - linux,default-trigger : see + Documentation/devicetree/bindings/leds/common.txt + + b) Optional properties for sub-nodes related to hardware controlled LEDs: + - brcm,hardware-controlled : Boolean, makes this LED hardware controlled. + Default : false + - brcm,link-signal-sources : An array of hardware link + signal sources. Up to four link hardware signals can get muxed into + these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may + be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs + 4 to 7. A signal can be muxed to more than one LED, and one LED can + have more than one source signal. + - brcm,activity-signal-sources : An array of hardware activity + signal sources. Up to four activity hardware signals can get muxed into + these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may + be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs + 4 to 7. A signal can be muxed to more than one LED, and one LED can + have more than one source signal. + +Examples: +Scenario 1 : BCM6328 with 4 EPHY LEDs + leds0: led-controller@10000800 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10000800 0x24>; + + alarm_red@2 { + reg = <2>; + active-low; + label = "red:alarm"; + }; + inet_green@3 { + reg = <3>; + active-low; + label = "green:inet"; + }; + power_green@4 { + reg = <4>; + active-low; + label = "green:power"; + default-state = "on"; + }; + ephy0_spd@17 { + reg = <17>; + brcm,hardware-controlled; + }; + ephy1_spd@18 { + reg = <18>; + brcm,hardware-controlled; + }; + ephy2_spd@19 { + reg = <19>; + brcm,hardware-controlled; + }; + ephy3_spd@20 { + reg = <20>; + brcm,hardware-controlled; + }; + }; + +Scenario 2 : BCM63268 with Serial/GPHY0 LEDs + leds0: led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + brcm,serial-leds; + brcm,serial-dat-low; + brcm,serial-shift-inv; + + gphy0_spd0@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + }; + gphy0_spd1@1 { + reg = <1>; + brcm,hardware-controlled; + brcm,link-signal-sources = <1>; + }; + inet_red@2 { + reg = <2>; + active-low; + label = "red:inet"; + }; + dsl_green@3 { + reg = <3>; + active-low; + label = "green:dsl"; + }; + usb_green@4 { + reg = <4>; + active-low; + label = "green:usb"; + }; + wps_green@7 { + reg = <7>; + active-low; + label = "green:wps"; + }; + inet_green@8 { + reg = <8>; + active-low; + label = "green:inet"; + }; + ephy0_act@9 { + reg = <9>; + brcm,hardware-controlled; + }; + ephy1_act@10 { + reg = <10>; + brcm,hardware-controlled; + }; + ephy2_act@11 { + reg = <11>; + brcm,hardware-controlled; + }; + gphy0_act@12 { + reg = <12>; + brcm,hardware-controlled; + }; + ephy0_spd@13 { + reg = <13>; + brcm,hardware-controlled; + }; + ephy1_spd@14 { + reg = <14>; + brcm,hardware-controlled; + }; + ephy2_spd@15 { + reg = <15>; + brcm,hardware-controlled; + }; + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; + }; + +Scenario 3 : BCM6362 with 1 LED for each EPHY + leds0: led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + brcm,activity-signal-sources = <0>; + /* USB link/activity routed to USB LED */ + }; + inet@1 { + reg = <1>; + brcm,hardware-controlled; + brcm,activity-signal-sources = <1>; + /* INET activity routed to INET LED */ + }; + ephy0@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4>; + /* EPHY0 link routed to EPHY0 LED */ + }; + ephy1@5 { + reg = <5>; + brcm,hardware-controlled; + brcm,link-signal-sources = <5>; + /* EPHY1 link routed to EPHY1 LED */ + }; + ephy2@6 { + reg = <6>; + brcm,hardware-controlled; + brcm,link-signal-sources = <6>; + /* EPHY2 link routed to EPHY2 LED */ + }; + ephy3@7 { + reg = <7>; + brcm,hardware-controlled; + brcm,link-signal-sources = <7>; + /* EPHY3 link routed to EPHY3 LED */ + }; + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; + }; + +Scenario 4 : BCM6362 with 1 LED for all EPHYs + leds0: led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0 1>; + brcm,activity-signal-sources = <0 1>; + /* USB/INET link/activity routed to USB LED */ + }; + ephy@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4 5 6 7>; + /* EPHY0/1/2/3 link routed to EPHY0 LED */ + }; + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; + }; + +Scenario 5 : BCM6362 with EPHY LEDs swapped + leds0: led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + brcm,activity-signal-sources = <0 1>; + /* USB link/act and INET act routed to USB LED */ + }; + ephy0@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <7>; + /* EPHY3 link routed to EPHY0 LED */ + }; + ephy1@5 { + reg = <5>; + brcm,hardware-controlled; + brcm,link-signal-sources = <6>; + /* EPHY2 link routed to EPHY1 LED */ + }; + ephy2@6 { + reg = <6>; + brcm,hardware-controlled; + brcm,link-signal-sources = <5>; + /* EPHY1 link routed to EPHY2 LED */ + }; + ephy3@7 { + reg = <7>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4>; + /* EPHY0 link routed to EPHY3 LED */ + }; + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-bcm6358.txt b/kernel/Documentation/devicetree/bindings/leds/leds-bcm6358.txt new file mode 100644 index 000000000..b22a55bcc --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/leds-bcm6358.txt @@ -0,0 +1,145 @@ +LEDs connected to Broadcom BCM6358 controller + +This controller is present on BCM6358 and BCM6368. +In these SoCs there are Serial LEDs (LEDs connected to a 74x164 controller), +which can either be controlled by software (exporting the 74x164 as spi-gpio. +See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or +by hardware using this driver. + +Required properties: + - compatible : should be "brcm,bcm6358-leds". + - #address-cells : must be 1. + - #size-cells : must be 0. + - reg : BCM6358 LED controller address and size. + +Optional properties: + - brcm,clk-div : SCK signal divider. Possible values are 1, 2, 4 and 8. + Default : 1 + - brcm,clk-dat-low : Boolean, makes clock and data signals active low. + Default : false + +Each LED is represented as a sub-node of the brcm,bcm6358-leds device. + +LED sub-node required properties: + - reg : LED pin number (only LEDs 0 to 31 are valid). + +LED sub-node optional properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + - active-low : Boolean, makes LED active low. + Default : false + - default-state : see + Documentation/devicetree/bindings/leds/leds-gpio.txt + - linux,default-trigger : see + Documentation/devicetree/bindings/leds/common.txt + +Examples: +Scenario 1 : BCM6358 + leds0: led-controller@fffe00d0 { + compatible = "brcm,bcm6358-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xfffe00d0 0x8>; + + alarm_white { + reg = <0>; + active-low; + label = "white:alarm"; + }; + tv_white { + reg = <2>; + active-low; + label = "white:tv"; + }; + tel_white { + reg = <3>; + active-low; + label = "white:tel"; + }; + adsl_white { + reg = <4>; + active-low; + label = "white:adsl"; + }; + }; + +Scenario 2 : BCM6368 + leds0: led-controller@100000d0 { + compatible = "brcm,bcm6358-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x100000d0 0x8>; + brcm,pol-low; + brcm,clk-div = <4>; + + power_red { + reg = <0>; + active-low; + label = "red:power"; + }; + power_green { + reg = <1>; + active-low; + label = "green:power"; + default-state = "on"; + }; + power_blue { + reg = <2>; + label = "blue:power"; + }; + broadband_red { + reg = <3>; + active-low; + label = "red:broadband"; + }; + broadband_green { + reg = <4>; + label = "green:broadband"; + }; + broadband_blue { + reg = <5>; + active-low; + label = "blue:broadband"; + }; + wireless_red { + reg = <6>; + active-low; + label = "red:wireless"; + }; + wireless_green { + reg = <7>; + active-low; + label = "green:wireless"; + }; + wireless_blue { + reg = <8>; + label = "blue:wireless"; + }; + phone_red { + reg = <9>; + active-low; + label = "red:phone"; + }; + phone_green { + reg = <10>; + active-low; + label = "green:phone"; + }; + phone_blue { + reg = <11>; + label = "blue:phone"; + }; + upgrading_red { + reg = <12>; + active-low; + label = "red:upgrading"; + }; + upgrading_green { + reg = <13>; + active-low; + label = "green:upgrading"; + }; + upgrading_blue { + reg = <14>; + label = "blue:upgrading"; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-ktd2692.txt b/kernel/Documentation/devicetree/bindings/leds/leds-ktd2692.txt new file mode 100644 index 000000000..853737452 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/leds-ktd2692.txt @@ -0,0 +1,50 @@ +* Kinetic Technologies - KTD2692 Flash LED Driver + +KTD2692 is the ideal power solution for high-power flash LEDs. +It uses ExpressWire single-wire programming for maximum flexibility. + +The ExpressWire interface through CTRL pin can control LED on/off and +enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current, +Flash timeout, LVP(low voltage protection). + +Also, When the AUX pin is pulled high while CTRL pin is high, +LED current will be ramped up to the flash-mode current level. + +Required properties: +- compatible : Should be "kinetic,ktd2692". +- ctrl-gpios : Specifier of the GPIO connected to CTRL pin. +- aux-gpios : Specifier of the GPIO connected to AUX pin. + +Optional properties: +- vin-supply : "vin" LED supply (2.7V to 5.5V). + See Documentation/devicetree/bindings/regulator/regulator.txt + +A discrete LED element connected to the device must be represented by a child +node - See Documentation/devicetree/bindings/leds/common.txt + +Required properties for flash LED child nodes: + See Documentation/devicetree/bindings/leds/common.txt +- led-max-microamp : Minimum Threshold for Timer protection + is defined internally (Maximum 300mA). +- flash-max-microamp : Flash LED maximum current + Formula : I(mA) = 15000 / Rset. +- flash-max-timeout-us : Flash LED maximum timeout. + +Optional properties for flash LED child nodes: +- label : See Documentation/devicetree/bindings/leds/common.txt + +Example: + +ktd2692 { + compatible = "kinetic,ktd2692"; + ctrl-gpios = <&gpc0 1 0>; + aux-gpios = <&gpc0 2 0>; + vin-supply = <&vbat>; + + flash-led { + label = "ktd2692-flash"; + led-max-microamp = <300000>; + flash-max-microamp = <1500000>; + flash-max-timeout-us = <1835000>; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-netxbig.txt b/kernel/Documentation/devicetree/bindings/leds/leds-netxbig.txt new file mode 100644 index 000000000..5ef92a26d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/leds-netxbig.txt @@ -0,0 +1,92 @@ +Binding for the CPLD LEDs (GPIO extension bus) found on some LaCie/Seagate +boards (Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-leds". +- gpio-ext: Phandle for the gpio-ext bus. + +Optional properties: +- timers: Timer array. Each timer entry is represented by three integers: + Mode (gpio-ext bus), delay_on and delay_off. + +Each LED is represented as a sub-node of the netxbig-leds device. + +Required sub-node properties: +- mode-addr: Mode register address on gpio-ext bus. +- mode-val: Mode to value mapping. Each entry is represented by two integers: + A mode and the corresponding value on the gpio-ext bus. +- bright-addr: Brightness register address on gpio-ext bus. +- max-brightness: Maximum brightness value. + +Optional sub-node properties: +- label: Name for this LED. If omitted, the label is taken from the node name. +- linux,default-trigger: Trigger assigned to the LED. + +Example: + +netxbig-leds { + compatible = "lacie,netxbig-leds"; + + gpio-ext = &gpio_ext; + + timers = <NETXBIG_LED_TIMER1 500 500 + NETXBIG_LED_TIMER2 500 1000>; + + blue-power { + label = "netxbig:blue:power"; + mode-addr = <0>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 1 + NETXBIG_LED_TIMER1 3 + NETXBIG_LED_TIMER2 7>; + bright-addr = <1>; + max-brightness = <7>; + }; + red-power { + label = "netxbig:red:power"; + mode-addr = <0>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <1>; + max-brightness = <7>; + }; + blue-sata0 { + label = "netxbig:blue:sata0"; + mode-addr = <3>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 7 + NETXBIG_LED_SATA 1 + NETXBIG_LED_TIMER1 3>; + bright-addr = <2>; + max-brightness = <7>; + }; + red-sata0 { + label = "netxbig:red:sata0"; + mode-addr = <3>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <2>; + max-brightness = <7>; + }; + blue-sata1 { + label = "netxbig:blue:sata1"; + mode-addr = <4>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 7 + NETXBIG_LED_SATA 1 + NETXBIG_LED_TIMER1 3>; + bright-addr = <2>; + max-brightness = <7>; + }; + red-sata1 { + label = "netxbig:red:sata1"; + mode-addr = <4>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <2>; + max-brightness = <7>; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-ns2.txt b/kernel/Documentation/devicetree/bindings/leds/leds-ns2.txt index aef3aca34..9f81258a5 100644 --- a/kernel/Documentation/devicetree/bindings/leds/leds-ns2.txt +++ b/kernel/Documentation/devicetree/bindings/leds/leds-ns2.txt @@ -8,6 +8,9 @@ Each LED is represented as a sub-node of the ns2-leds device. Required sub-node properties: - cmd-gpio: Command LED GPIO. See OF device-tree GPIO specification. - slow-gpio: Slow LED GPIO. See OF device-tree GPIO specification. +- modes-map: A mapping between LED modes (off, on or SATA activity blinking) and + the corresponding cmd-gpio/slow-gpio values. All the GPIO values combinations + should be given in order to avoid having an unknown mode at driver probe time. Optional sub-node properties: - label: Name for this LED. If omitted, the label is taken from the node name. @@ -15,6 +18,8 @@ Optional sub-node properties: Example: +#include <dt-bindings/leds/leds-ns2.h> + ns2-leds { compatible = "lacie,ns2-leds"; @@ -22,5 +27,9 @@ ns2-leds { label = "ns2:blue:sata"; slow-gpio = <&gpio0 29 0>; cmd-gpio = <&gpio0 30 0>; + modes-map = <NS_V2_LED_OFF 0 1 + NS_V2_LED_ON 1 0 + NS_V2_LED_ON 0 0 + NS_V2_LED_SATA 1 1>; }; }; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-powernv.txt b/kernel/Documentation/devicetree/bindings/leds/leds-powernv.txt new file mode 100644 index 000000000..66655690f --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/leds-powernv.txt @@ -0,0 +1,26 @@ +Device Tree binding for LEDs on IBM Power Systems +------------------------------------------------- + +Required properties: +- compatible : Should be "ibm,opal-v3-led". +- led-mode : Should be "lightpath" or "guidinglight". + +Each location code of FRU/Enclosure must be expressed in the +form of a sub-node. + +Required properties for the sub nodes: +- led-types : Supported LED types (attention/identify/fault) provided + in the form of string array. + +Example: + +leds { + compatible = "ibm,opal-v3-led"; + led-mode = "lightpath"; + + U78C9.001.RST0027-P1-C1 { + led-types = "identify", "fault"; + }; + ... + ... +}; diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-tlc591xx.txt b/kernel/Documentation/devicetree/bindings/leds/leds-tlc591xx.txt new file mode 100644 index 000000000..3bbbf7024 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/leds/leds-tlc591xx.txt @@ -0,0 +1,40 @@ +LEDs connected to tlc59116 or tlc59108 + +Required properties +- compatible: should be "ti,tlc59116" or "ti,tlc59108" +- #address-cells: must be 1 +- #size-cells: must be 0 +- reg: typically 0x68 + +Each led is represented as a sub-node of the ti,tlc59116. +See Documentation/devicetree/bindings/leds/common.txt + +LED sub-node properties: +- reg: number of LED line, 0 to 15 or 0 to 7 +- label: (optional) name of LED +- linux,default-trigger : (optional) + +Examples: + +tlc59116@68 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,tlc59116"; + reg = <0x68>; + + wan@0 { + label = "wrt1900ac:amber:wan"; + reg = <0x0>; + }; + + 2g@2 { + label = "wrt1900ac:white:2g"; + reg = <0x2>; + }; + + alive@9 { + label = "wrt1900ac:green:alive"; + reg = <0x9>; + linux,default_trigger = "heartbeat"; + }; +}; |