diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/gpio')
14 files changed, 408 insertions, 30 deletions
diff --git a/kernel/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt new file mode 100644 index 000000000..b405b4410 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt @@ -0,0 +1,86 @@ +Broadcom STB "UPG GIO" GPIO controller + +The controller's registers are organized as sets of eight 32-bit +registers with each set controlling a bank of up to 32 pins. A single +interrupt is shared for all of the banks handled by the controller. + +Required properties: + +- compatible: + Must be "brcm,brcmstb-gpio" + +- reg: + Define the base and range of the I/O address space containing + the brcmstb GPIO controller registers + +- #gpio-cells: + Should be <2>. The first cell is the pin number (within the controller's + pin space), and the second is used for the following: + bit[0]: polarity (0 for active-high, 1 for active-low) + +- gpio-controller: + Specifies that the node is a GPIO controller. + +- brcm,gpio-bank-widths: + Number of GPIO lines for each bank. Number of elements must + correspond to number of banks suggested by the 'reg' property. + +Optional properties: + +- interrupts: + The interrupt shared by all GPIO lines for this controller. + +- interrupt-parent: + phandle of the parent interrupt controller + +- interrupts-extended: + Alternate form of specifying interrupts and parents that allows for + multiple parents. This takes precedence over 'interrupts' and + 'interrupt-parent'. Wakeup-capable GPIO controllers often route their + wakeup interrupt lines through a different interrupt controller than the + primary interrupt line, making this property necessary. + +- #interrupt-cells: + Should be <2>. The first cell is the GPIO number, the second should specify + flags. The following subset of flags is supported: + - bits[3:0] trigger type and level flags + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + Valid combinations are 1, 2, 3, 4, 8. + See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +- interrupt-controller: + Marks the device node as an interrupt controller + +- wakeup-source: + GPIOs for this controller can be used as a wakeup source + +Example: + upg_gio: gpio@f040a700 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; + gpio-controller; + interrupt-controller; + reg = <0xf040a700 0x80>; + interrupt-parent = <&irq0_intc>; + interrupts = <0x6>; + brcm,gpio-bank-widths = <32 32 32 24>; + }; + + upg_gio_aon: gpio@f04172c0 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; + gpio-controller; + interrupt-controller; + reg = <0xf04172c0 0x40>; + interrupt-parent = <&irq0_aon_intc>; + interrupts = <0x6>; + interrupts-extended = <&irq0_aon_intc 0x6>, + <&aon_pm_l2_intc 0x5>; + wakeup-source; + brcm,gpio-bank-widths = <18 4>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-ath79.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-ath79.txt new file mode 100644 index 000000000..c52285101 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-ath79.txt @@ -0,0 +1,38 @@ +Binding for Qualcomm Atheros AR7xxx/AR9xxx GPIO controller + +Required properties: +- compatible: has to be "qca,<soctype>-gpio" and one of the following + fallbacks: + - "qca,ar7100-gpio" + - "qca,ar9340-gpio" +- reg: Base address and size of the controllers memory area +- gpio-controller : Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters. +- ngpios: Should be set to the number of GPIOs available on the SoC. + +Optional properties: +- interrupt-parent: phandle of the parent interrupt controller. +- interrupts: Interrupt specifier for the controllers interrupt. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode interrupt + source, should be 2 + +Please refer to interrupts.txt in this directory for details of the common +Interrupt Controllers bindings used by client devices. + +Example: + + gpio@18040000 { + compatible = "qca,ar9132-gpio", "qca,ar7100-gpio"; + reg = <0x18040000 0x30>; + interrupts = <2>; + + ngpios = <22>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt new file mode 100644 index 000000000..d7e123fc9 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt @@ -0,0 +1,50 @@ +CSR SiRFatlas7 GPIO controller bindings + +Required properties: +- compatible : "sirf,atlas7-gpio" +- reg : Address range of the pinctrl registers +- interrupts : Interrupts used by every GPIO group +- gpio-banks : How many gpio banks on this controller +- gpio-controller : Indicates this device is a GPIO controller +- interrupt-controller : Marks the device node as an interrupt controller + +The GPIO controller also acts as an interrupt controller. It uses the default +two cells specifier as described in Documentation/devicetree/bindings/ +interrupt-controller/interrupts.txt. + +Example: + + gpio_0: gpio_mediam@17040000 { + compatible = "sirf,atlas7-gpio"; + reg = <0x17040000 0x1000>; + interrupts = <0 13 0>, <0 14 0>; + + #gpio-cells = <2>; + #interrupt-cells = <2>; + + gpio-controller; + interrupt-controller; + + gpio-banks = <2>; + gpio-ranges = <&pinctrl 0 0 0>, + <&pinctrl 32 0 0>; + gpio-ranges-group-names = "lvds_gpio_grp", + "uart_nand_gpio_grp"; + }; + + leds { + compatible = "gpio-leds"; + + led1 { + gpios = <&gpio_1 15 0>; + ... + }; + + led2 { + gpios = <&gpio_2 34 0>; + ... + }; + }; + +Please refer to gpio.txt in this directory for details of the common +gpio properties used by devices. diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt new file mode 100644 index 000000000..170194af3 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt @@ -0,0 +1,22 @@ +Axis ETRAX FS General I/O controller bindings + +Required properties: + +- compatible: one of: + - "axis,etraxfs-gio" + - "axis,artpec3-gio" +- reg: Physical base address and length of the controller's registers. +- #gpio-cells: Should be 3 + - The first cell is the gpio offset number. + - The second cell is reserved and is currently unused. + - The third cell is the port number (hex). +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + + gio: gpio@b001a000 { + compatible = "axis,etraxfs-gio"; + reg = <0xb001a000 0x1000>; + gpio-controller; + #gpio-cells = <3>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt new file mode 100644 index 000000000..120bc4971 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -0,0 +1,26 @@ +* Freescale MPC512x/MPC8xxx/Layerscape GPIO controller + +Required properties: +- compatible : Should be "fsl,<soc>-gpio" + The following <soc>s are known to be supported: + mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq. +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all 32 pins. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + +Optional properties: +- little-endian : GPIO registers are used as little endian. If not + present registers are used as big endian by default. + +Example: + +gpio0: gpio@1100 { + compatible = "fsl,mpc5125-gpio"; + #gpio-cells = <2>; + reg = <0x1100 0x080>; + interrupts = <78 0x8>; + status = "okay"; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt deleted file mode 100644 index ac20e68a0..000000000 --- a/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt +++ /dev/null @@ -1,26 +0,0 @@ -MSM GPIO controller bindings - -Required properties: -- compatible: - - "qcom,msm-gpio" for MSM controllers -- #gpio-cells : Should be two. - - first cell is the pin number - - second cell is used to specify optional parameters (unused) -- gpio-controller : Marks the device node as a GPIO controller. -- #interrupt-cells : Should be 2. -- interrupt-controller: Mark the device node as an interrupt controller -- interrupts : Specify the TLMM summary interrupt number -- ngpio : Specify the number of MSM GPIOs - -Example: - - msmgpio: gpio@fd510000 { - compatible = "qcom,msm-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0xfd510000 0x4000>; - interrupts = <0 208 0>; - ngpio = <150>; - }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index b9a42f294..13df9933f 100644 --- a/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -24,6 +24,7 @@ Required properties: ti,tca6408 ti,tca6416 ti,tca6424 + ti,tca9539 exar,xra1202 Example: diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-xlp.txt new file mode 100644 index 000000000..262ee4ddf --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-xlp.txt @@ -0,0 +1,47 @@ +Netlogic XLP Family GPIO +======================== + +This GPIO driver is used for following Netlogic XLP SoCs: + XLP832, XLP316, XLP208, XLP980, XLP532 + +Required properties: +------------------- + +- compatible: Should be one of the following: + - "netlogic,xlp832-gpio": For Netlogic XLP832 + - "netlogic,xlp316-gpio": For Netlogic XLP316 + - "netlogic,xlp208-gpio": For Netlogic XLP208 + - "netlogic,xlp980-gpio": For Netlogic XLP980 + - "netlogic,xlp532-gpio": For Netlogic XLP532 +- reg: Physical base address and length of the controller's registers. +- #gpio-cells: Should be two. The first cell is the pin number and the second + cell is used to specify optional parameters (currently unused). +- gpio-controller: Marks the device node as a GPIO controller. +- nr-gpios: Number of GPIO pins supported by the controller. +- interrupt-cells: Should be two. The first cell is the GPIO Number. The + second cell is used to specify flags. The following subset of flags is + supported: + - trigger type: + 1 = low to high edge triggered. + 2 = high to low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. +- interrupts: Interrupt number for this device. +- interrupt-parent: phandle of the parent interrupt controller. +- interrupt-controller: Identifies the node as an interrupt controller. + +Example: + + gpio: xlp_gpio@34000 { + compatible = "netlogic,xlp316-gpio"; + reg = <0 0x34100 0x1000 + 0 0x35100 0x1000>; + #gpio-cells = <2>; + gpio-controller; + nr-gpios = <57>; + + #interrupt-cells = <2>; + interrupt-parent = <&pic>; + interrupts = <39>; + interrupt-controller; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt index 986371a4b..7b542657f 100644 --- a/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt @@ -6,12 +6,19 @@ Required properties: - First cell is the GPIO line number - Second cell is used to specify optional parameters (unused) -- compatible : Should be "xlnx,zynq-gpio-1.0" +- compatible : Should be "xlnx,zynq-gpio-1.0" or "xlnx,zynqmp-gpio-1.0" - clocks : Clock specifier (see clock bindings for details) - gpio-controller : Marks the device node as a GPIO controller. - interrupts : Interrupt specifier (see interrupt bindings for details) - interrupt-parent : Must be core interrupt controller +- interrupt-controller : Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. - reg : Address and length of the register set for the device Example: @@ -22,5 +29,7 @@ Example: gpio-controller; interrupt-parent = <&intc>; interrupts = <0 20 4>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0xe000a000 0x1000>; }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio.txt index 5788d5cf1..069cdf6f9 100644 --- a/kernel/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio.txt @@ -16,7 +16,9 @@ properties, each containing a 'gpio-list': GPIO properties should be named "[<name>-]gpios", with <name> being the purpose of this GPIO for the device. While a non-existent <name> is considered valid for compatibility reasons (resolving to the "gpios" property), it is not allowed -for new bindings. +for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old +bindings use it, but are only supported for compatibility reasons and should not +be used for newer bindings since it has been deprecated. GPIO properties can contain one or more GPIO phandles, but only in exceptional cases should they contain more than one. If your device uses several GPIOs with @@ -52,9 +54,13 @@ only uses one. gpio-specifier may encode: bank, pin position inside the bank, whether pin is open-drain and whether pin is logically inverted. + Exact meaning of each specifier cell is controller specific, and must -be documented in the device tree binding for the device. Use the macros -defined in include/dt-bindings/gpio/gpio.h whenever possible: +be documented in the device tree binding for the device. + +Most controllers are however specifying a generic flag bitfield +in the last cell, so for these, use the macros defined in +include/dt-bindings/gpio/gpio.h whenever possible: Example of a node using GPIOs: @@ -65,6 +71,15 @@ Example of a node using GPIOs: GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller. +Optional standard bitfield specifiers for the last cell: + +- Bit 0: 0 means active high, 1 means active low +- Bit 1: 1 means single-ended wiring, see: + https://en.wikipedia.org/wiki/Single-ended_triode + When used with active-low, this means open drain/collector, see: + https://en.wikipedia.org/wiki/Open_collector + When used with active-high, this means open source/emitter + 1.1) GPIO specifier best practices ---------------------------------- @@ -116,6 +131,30 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +Optionally, a GPIO controller may have a "ngpios" property. This property +indicates the number of in-use slots of available slots for GPIOs. The +typical example is something like this: the hardware register is 32 bits +wide, but only 18 of the bits have a physical counterpart. The driver is +generally written so that all 32 bits can be used, but the IP block is reused +in a lot of designs, some using all 32 bits, some using 18 and some using +12. In this case, setting "ngpios = <18>;" informs the driver that only the +first 18 GPIOs, at local offset 0 .. 17, are in use. + +If these GPIOs do not happen to be the first N GPIOs at offset 0...N-1, an +additional bitmask is needed to specify which GPIOs are actually in use, +and which are dummies. The bindings for this case has not yet been +specified, but should be specified if/when such hardware appears. + +Example: + +gpio-controller@00000000 { + compatible = "foo"; + reg = <0x00000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <18>; +} + The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism providing automatic GPIO request and configuration as part of the gpio-controller's driver probe function. diff --git a/kernel/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt b/kernel/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt new file mode 100644 index 000000000..50ec2e690 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt @@ -0,0 +1,22 @@ +Binding for the GPIO extension bus found on some LaCie/Seagate boards +(Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-gpio-ext". +- addr-gpios: GPIOs representing the address register (LSB -> MSB). +- data-gpios: GPIOs representing the data register (LSB -> MSB). +- enable-gpio: latches the new configuration (address, data) on raising edge. + +Example: + +netxbig_gpio_ext: netxbig-gpio-ext { + compatible = "lacie,netxbig-gpio-ext"; + + addr-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH + &gpio1 16 GPIO_ACTIVE_HIGH + &gpio1 17 GPIO_ACTIVE_HIGH>; + data-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH + &gpio1 13 GPIO_ACTIVE_HIGH + &gpio1 14 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt new file mode 100644 index 000000000..eb7cdd69e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt @@ -0,0 +1,39 @@ +NXP LPC18xx/43xx GPIO controller Device Tree Bindings +----------------------------------------------------- + +Required properties: +- compatible : Should be "nxp,lpc1850-gpio" +- reg : Address and length of the register set for the device +- clocks : Clock specifier (see clock bindings for details) +- gpio-controller : Marks the device node as a GPIO controller. +- #gpio-cells : Should be two + - First cell is the GPIO line number + - Second cell is used to specify polarity + +Optional properties: +- gpio-ranges : Mapping between GPIO and pinctrl + +Example: +#define LPC_GPIO(port, pin) (port * 32 + pin) +#define LPC_PIN(port, pin) (0x##port * 32 + pin) + +gpio: gpio@400f4000 { + compatible = "nxp,lpc1850-gpio"; + reg = <0x400f4000 0x4000>; + clocks = <&ccu1 CLK_CPU_GPIO>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl LPC_GPIO(0,0) LPC_PIN(0,0) 2>, + ... + <&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5) 7>; +}; + +gpio_joystick { + compatible = "gpio-keys-polled"; + ... + + button@0 { + ... + gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 38fb86f28..f60e2f477 100644 --- a/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -9,6 +9,7 @@ Required Properties: - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2-W) compatible GPIO controller. - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller. - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. + - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. - "renesas,gpio-rcar": for generic R-Car GPIO controller. - reg: Base address and length of each memory resource used by the GPIO diff --git a/kernel/Documentation/devicetree/bindings/gpio/zx296702-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/zx296702-gpio.txt new file mode 100644 index 000000000..0dab156fc --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/zx296702-gpio.txt @@ -0,0 +1,24 @@ +ZTE ZX296702 GPIO controller + +Required properties: +- compatible : "zte,zx296702-gpio" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt mapping for GPIO IRQ. +- gpio-ranges : Interaction with the PINCTRL subsystem. + +gpio1: gpio@b008040 { + compatible = "zte,zx296702-gpio"; + reg = <0xb008040 0x40>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = < &pmx0 0 54 2 &pmx0 2 59 14>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <2>; + clock-names = "gpio_pclk"; + clocks = <&lsp0clk ZX296702_GPIO_CLK>; +}; |