diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/drm')
14 files changed, 0 insertions, 731 deletions
diff --git a/kernel/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt b/kernel/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt deleted file mode 100644 index 46525ea3e..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt +++ /dev/null @@ -1,30 +0,0 @@ -Device Tree bindings for Armada DRM CRTC driver - -Required properties: - - compatible: value should be "marvell,dove-lcd". - - reg: base address and size of the LCD controller - - interrupts: single interrupt number for the LCD controller - - port: video output port with endpoints, as described by graph.txt - -Optional properties: - - - clocks: as described by clock-bindings.txt - - clock-names: as described by clock-bindings.txt - "axiclk" - axi bus clock for pixel clock - "plldivider" - pll divider clock for pixel clock - "ext_ref_clk0" - external clock 0 for pixel clock - "ext_ref_clk1" - external clock 1 for pixel clock - -Note: all clocks are optional but at least one must be specified. -Further clocks may be added in the future according to requirements of -different SoCs. - -Example: - - lcd0: lcd-controller@820000 { - compatible = "marvell,dove-lcd"; - reg = <0x820000 0x1000>; - interrupts = <47>; - clocks = <&si5351 0>; - clock-names = "ext_ref_clk_1"; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt b/kernel/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt deleted file mode 100644 index ebc1a914b..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt +++ /dev/null @@ -1,53 +0,0 @@ -Device-Tree bindings for Atmel's HLCDC (High LCD Controller) DRM driver - -The Atmel HLCDC Display Controller is subdevice of the HLCDC MFD device. -See ../mfd/atmel-hlcdc.txt for more details. - -Required properties: - - compatible: value should be "atmel,hlcdc-display-controller" - - pinctrl-names: the pin control state names. Should contain "default". - - pinctrl-0: should contain the default pinctrl states. - - #address-cells: should be set to 1. - - #size-cells: should be set to 0. - -Required children nodes: - Children nodes are encoding available output ports and their connections - to external devices using the OF graph reprensentation (see ../graph.txt). - At least one port node is required. - -Example: - - hlcdc: hlcdc@f0030000 { - compatible = "atmel,sama5d3-hlcdc"; - reg = <0xf0030000 0x2000>; - interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; - clock-names = "periph_clk","sys_clk", "slow_clk"; - status = "disabled"; - - hlcdc-display-controller { - compatible = "atmel,hlcdc-display-controller"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - hlcdc_panel_output: endpoint@0 { - reg = <0>; - remote-endpoint = <&panel_input>; - }; - }; - }; - - hlcdc_pwm: hlcdc-pwm { - compatible = "atmel,hlcdc-pwm"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_lcd_pwm>; - #pwm-cells = <3>; - }; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt b/kernel/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt deleted file mode 100644 index a905c1413..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt +++ /dev/null @@ -1,50 +0,0 @@ -DesignWare HDMI bridge bindings - -Required properties: -- compatible: platform specific such as: - * "snps,dw-hdmi-tx" - * "fsl,imx6q-hdmi" - * "fsl,imx6dl-hdmi" - * "rockchip,rk3288-dw-hdmi" -- reg: Physical base address and length of the controller's registers. -- interrupts: The HDMI interrupt number -- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks, - as described in Documentation/devicetree/bindings/clock/clock-bindings.txt, - the clocks are soc specific, the clock-names should be "iahb", "isfr" --port@[X]: SoC specific port nodes with endpoint definitions as defined - in Documentation/devicetree/bindings/media/video-interfaces.txt, - please refer to the SoC specific binding document: - * Documentation/devicetree/bindings/drm/imx/hdmi.txt - * Documentation/devicetree/bindings/video/dw_hdmi-rockchip.txt - -Optional properties -- reg-io-width: the width of the reg:1,4, default set to 1 if not present -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing -- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" - -Example: - hdmi: hdmi@0120000 { - compatible = "fsl,imx6q-hdmi"; - reg = <0x00120000 0x9000>; - interrupts = <0 115 0x04>; - gpr = <&gpr>; - clocks = <&clks 123>, <&clks 124>; - clock-names = "iahb", "isfr"; - ddc-i2c-bus = <&i2c2>; - - port@0 { - reg = <0>; - - hdmi_mux_0: endpoint { - remote-endpoint = <&ipu1_di0_hdmi>; - }; - }; - - port@1 { - reg = <1>; - - hdmi_mux_1: endpoint { - remote-endpoint = <&ipu1_di1_hdmi>; - }; - }; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/i2c/tda998x.txt b/kernel/Documentation/devicetree/bindings/drm/i2c/tda998x.txt deleted file mode 100644 index e9e4bce40..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/i2c/tda998x.txt +++ /dev/null @@ -1,29 +0,0 @@ -Device-Tree bindings for the NXP TDA998x HDMI transmitter - -Required properties; - - compatible: must be "nxp,tda998x" - - - reg: I2C address - -Optional properties: - - interrupts: interrupt number and trigger type - default: polling - - - pinctrl-0: pin control group to be used for - screen plug/unplug interrupt. - - - pinctrl-names: must contain a "default" entry. - - - video-ports: 24 bits value which defines how the video controller - output is wired to the TDA998x input - default: <0x230145> - -Example: - - tda998x: hdmi-encoder { - compatible = "nxp,tda998x"; - reg = <0x70>; - interrupt-parent = <&gpio0>; - interrupts = <27 2>; /* falling edge */ - pinctrl-0 = <&pmx_camera>; - pinctrl-names = "default"; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt b/kernel/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt deleted file mode 100644 index e75f0e549..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt +++ /dev/null @@ -1,83 +0,0 @@ -Freescale i.MX DRM master device -================================ - -The freescale i.MX DRM master device is a virtual device needed to list all -IPU or other display interface nodes that comprise the graphics subsystem. - -Required properties: -- compatible: Should be "fsl,imx-display-subsystem" -- ports: Should contain a list of phandles pointing to display interface ports - of IPU devices - -example: - -display-subsystem { - compatible = "fsl,display-subsystem"; - ports = <&ipu_di0>; -}; - - -Freescale i.MX IPUv3 -==================== - -Required properties: -- compatible: Should be "fsl,<chip>-ipu" -- reg: should be register base and length as documented in the - datasheet -- interrupts: Should contain sync interrupt and error interrupt, - in this order. -- resets: phandle pointing to the system reset controller and - reset line index, see reset/fsl,imx-src.txt for details -Optional properties: -- port@[0-3]: Port nodes with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. - Ports 0 and 1 should correspond to CSI0 and CSI1, - ports 2 and 3 should correspond to DI0 and DI1, respectively. - -example: - -ipu: ipu@18000000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx53-ipu"; - reg = <0x18000000 0x080000000>; - interrupts = <11 10>; - resets = <&src 2>; - - ipu_di0: port@2 { - reg = <2>; - - ipu_di0_disp0: endpoint { - remote-endpoint = <&display_in>; - }; - }; -}; - -Parallel display support -======================== - -Required properties: -- compatible: Should be "fsl,imx-parallel-display" -Optional properties: -- interface_pix_fmt: How this display is connected to the - display interface. Currently supported types: "rgb24", "rgb565", "bgr666" - and "lvds666". -- edid: verbatim EDID data block describing attached display. -- ddc: phandle describing the i2c bus handling the display data - channel -- port: A port node with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. - -example: - -display@di0 { - compatible = "fsl,imx-parallel-display"; - edid = [edid-data]; - interface-pix-fmt = "rgb24"; - - port { - display_in: endpoint { - remote-endpoint = <&ipu_di0_disp0>; - }; - }; -}; diff --git a/kernel/Documentation/devicetree/bindings/drm/imx/hdmi.txt b/kernel/Documentation/devicetree/bindings/drm/imx/hdmi.txt deleted file mode 100644 index 1b756cf9a..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/imx/hdmi.txt +++ /dev/null @@ -1,58 +0,0 @@ -Device-Tree bindings for HDMI Transmitter - -HDMI Transmitter -================ - -The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP -with accompanying PHY IP. - -Required properties: - - #address-cells : should be <1> - - #size-cells : should be <0> - - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi". - - gpr : should be <&gpr>. - The phandle points to the iomuxc-gpr region containing the HDMI - multiplexer control register. - - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described - in Documentation/devicetree/bindings/clock/clock-bindings.txt and - Documentation/devicetree/bindings/clock/imx6q-clock.txt. - - port@[0-4]: Up to four port nodes with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt, - corresponding to the four inputs to the HDMI multiplexer. - -Optional properties: - - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - -example: - - gpr: iomuxc-gpr@020e0000 { - /* ... */ - }; - - hdmi: hdmi@0120000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx6q-hdmi"; - reg = <0x00120000 0x9000>; - interrupts = <0 115 0x04>; - gpr = <&gpr>; - clocks = <&clks 123>, <&clks 124>; - clock-names = "iahb", "isfr"; - ddc-i2c-bus = <&i2c2>; - - port@0 { - reg = <0>; - - hdmi_mux_0: endpoint { - remote-endpoint = <&ipu1_di0_hdmi>; - }; - }; - - port@1 { - reg = <1>; - - hdmi_mux_1: endpoint { - remote-endpoint = <&ipu1_di1_hdmi>; - }; - }; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt b/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt deleted file mode 100644 index 9a2136643..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt +++ /dev/null @@ -1,146 +0,0 @@ -Device-Tree bindings for LVDS Display Bridge (ldb) - -LVDS Display Bridge -=================== - -The LVDS Display Bridge device tree node contains up to two lvds-channel -nodes describing each of the two LVDS encoder channels of the bridge. - -Required properties: - - #address-cells : should be <1> - - #size-cells : should be <0> - - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". - Both LDB versions are similar, but i.MX6 has an additional - multiplexer in the front to select any of the four IPU display - interfaces as input for each LVDS channel. - - gpr : should be <&gpr> on i.MX53 and i.MX6q. - The phandle points to the iomuxc-gpr region containing the LVDS - control register. -- clocks, clock-names : phandles to the LDB divider and selector clocks and to - the display interface selector clocks, as described in - Documentation/devicetree/bindings/clock/clock-bindings.txt - The following clocks are expected on i.MX53: - "di0_pll" - LDB LVDS channel 0 mux - "di1_pll" - LDB LVDS channel 1 mux - "di0" - LDB LVDS channel 0 gate - "di1" - LDB LVDS channel 1 gate - "di0_sel" - IPU1 DI0 mux - "di1_sel" - IPU1 DI1 mux - On i.MX6q the following additional clocks are needed: - "di2_sel" - IPU2 DI0 mux - "di3_sel" - IPU2 DI1 mux - The needed clock numbers for each are documented in - Documentation/devicetree/bindings/clock/imx5-clock.txt, and in - Documentation/devicetree/bindings/clock/imx6q-clock.txt. - -Optional properties: - - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q - - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, - not used on i.MX6q - - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should - be configured - one input will be distributed on both outputs in dual - channel mode - -LVDS Channel -============ - -Each LVDS Channel has to contain either an of graph link to a panel device node -or a display-timings node that describes the video timings for the connected -LVDS display as well as the fsl,data-mapping and fsl,data-width properties. - -Required properties: - - reg : should be <0> or <1> - - port: Input and output port nodes with endpoint definitions as defined in - Documentation/devicetree/bindings/graph.txt. - On i.MX5, the internal two-input-multiplexer is used. Due to hardware - limitations, only one input port (port@[0,1]) can be used for each channel - (lvds-channel@[0,1], respectively). - On i.MX6, there should be four input ports (port@[0-3]) that correspond - to the four LVDS multiplexer inputs. - A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected - to a panel input port. Optionally, the output port can be left out if - display-timings are used instead. - -Optional properties (required if display-timings are used): - - display-timings : A node that describes the display timings as defined in - Documentation/devicetree/bindings/video/display-timing.txt. - - fsl,data-mapping : should be "spwg" or "jeida" - This describes how the color bits are laid out in the - serialized LVDS signal. - - fsl,data-width : should be <18> or <24> - -example: - -gpr: iomuxc-gpr@53fa8000 { - /* ... */ -}; - -ldb: ldb@53fa8008 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx53-ldb"; - gpr = <&gpr>; - clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, - <&clks IMX5_CLK_LDB_DI1_SEL>, - <&clks IMX5_CLK_IPU_DI0_SEL>, - <&clks IMX5_CLK_IPU_DI1_SEL>, - <&clks IMX5_CLK_LDB_DI0_GATE>, - <&clks IMX5_CLK_LDB_DI1_GATE>; - clock-names = "di0_pll", "di1_pll", - "di0_sel", "di1_sel", - "di0", "di1"; - - /* Using an of-graph endpoint link to connect the panel */ - lvds-channel@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - port@0 { - reg = <0>; - - lvds0_in: endpoint { - remote-endpoint = <&ipu_di0_lvds0>; - }; - }; - - port@2 { - reg = <2>; - - lvds0_out: endpoint { - remote-endpoint = <&panel_in>; - }; - }; - }; - - /* Using display-timings and fsl,data-mapping/width instead */ - lvds-channel@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - fsl,data-mapping = "spwg"; - fsl,data-width = <24>; - - display-timings { - /* ... */ - }; - - port@1 { - reg = <1>; - - lvds1_in: endpoint { - remote-endpoint = <&ipu_di1_lvds1>; - }; - }; - }; -}; - -panel: lvds-panel { - /* ... */ - - port { - panel_in: endpoint { - remote-endpoint = <&lvds0_out>; - }; - }; -}; diff --git a/kernel/Documentation/devicetree/bindings/drm/msm/gpu.txt b/kernel/Documentation/devicetree/bindings/drm/msm/gpu.txt deleted file mode 100644 index 67d0a58db..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/msm/gpu.txt +++ /dev/null @@ -1,52 +0,0 @@ -Qualcomm adreno/snapdragon GPU - -Required properties: -- compatible: "qcom,adreno-3xx" -- reg: Physical base address and length of the controller's registers. -- interrupts: The interrupt signal from the gpu. -- clocks: device clocks - See ../clocks/clock-bindings.txt for details. -- clock-names: the following clocks are required: - * "core_clk" - * "iface_clk" - * "mem_iface_clk" -- qcom,chipid: gpu chip-id. Note this may become optional for future - devices if we can reliably read the chipid from hw -- qcom,gpu-pwrlevels: list of operating points - - compatible: "qcom,gpu-pwrlevels" - - for each qcom,gpu-pwrlevel: - - qcom,gpu-freq: requested gpu clock speed - - NOTE: downstream android driver defines additional parameters to - configure memory bandwidth scaling per OPP. - -Example: - -/ { - ... - - gpu: qcom,kgsl-3d0@4300000 { - compatible = "qcom,adreno-3xx"; - reg = <0x04300000 0x20000>; - reg-names = "kgsl_3d0_reg_memory"; - interrupts = <GIC_SPI 80 0>; - interrupt-names = "kgsl_3d0_irq"; - clock-names = - "core_clk", - "iface_clk", - "mem_iface_clk"; - clocks = - <&mmcc GFX3D_CLK>, - <&mmcc GFX3D_AHB_CLK>, - <&mmcc MMSS_IMEM_AHB_CLK>; - qcom,chipid = <0x03020100>; - qcom,gpu-pwrlevels { - compatible = "qcom,gpu-pwrlevels"; - qcom,gpu-pwrlevel@0 { - qcom,gpu-freq = <450000000>; - }; - qcom,gpu-pwrlevel@1 { - qcom,gpu-freq = <27000000>; - }; - }; - }; -}; diff --git a/kernel/Documentation/devicetree/bindings/drm/msm/hdmi.txt b/kernel/Documentation/devicetree/bindings/drm/msm/hdmi.txt deleted file mode 100644 index a29a55f3d..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/msm/hdmi.txt +++ /dev/null @@ -1,48 +0,0 @@ -Qualcomm adreno/snapdragon hdmi output - -Required properties: -- compatible: one of the following - * "qcom,hdmi-tx-8084" - * "qcom,hdmi-tx-8074" - * "qcom,hdmi-tx-8660" - * "qcom,hdmi-tx-8960" -- reg: Physical base address and length of the controller's registers -- reg-names: "core_physical" -- interrupts: The interrupt signal from the hdmi block. -- clocks: device clocks - See ../clocks/clock-bindings.txt for details. -- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin -- qcom,hdmi-tx-ddc-data-gpio: ddc data pin -- qcom,hdmi-tx-hpd-gpio: hpd pin -- core-vdda-supply: phandle to supply regulator -- hdmi-mux-supply: phandle to mux regulator - -Optional properties: -- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin -- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin - -Example: - -/ { - ... - - hdmi: qcom,hdmi-tx-8960@4a00000 { - compatible = "qcom,hdmi-tx-8960"; - reg-names = "core_physical"; - reg = <0x04a00000 0x1000>; - interrupts = <GIC_SPI 79 0>; - clock-names = - "core_clk", - "master_iface_clk", - "slave_iface_clk"; - clocks = - <&mmcc HDMI_APP_CLK>, - <&mmcc HDMI_M_AHB_CLK>, - <&mmcc HDMI_S_AHB_CLK>; - qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>; - qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>; - qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>; - core-vdda-supply = <&pm8921_hdmi_mvs>; - hdmi-mux-supply = <&ext_3p3v>; - }; -}; diff --git a/kernel/Documentation/devicetree/bindings/drm/msm/mdp.txt b/kernel/Documentation/devicetree/bindings/drm/msm/mdp.txt deleted file mode 100644 index 1a0598e52..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/msm/mdp.txt +++ /dev/null @@ -1,48 +0,0 @@ -Qualcomm adreno/snapdragon display controller - -Required properties: -- compatible: - * "qcom,mdp" - mdp4 -- reg: Physical base address and length of the controller's registers. -- interrupts: The interrupt signal from the display controller. -- connectors: array of phandles for output device(s) -- clocks: device clocks - See ../clocks/clock-bindings.txt for details. -- clock-names: the following clocks are required: - * "core_clk" - * "iface_clk" - * "lut_clk" - * "src_clk" - * "hdmi_clk" - * "mpd_clk" - -Optional properties: -- gpus: phandle for gpu device - -Example: - -/ { - ... - - mdp: qcom,mdp@5100000 { - compatible = "qcom,mdp"; - reg = <0x05100000 0xf0000>; - interrupts = <GIC_SPI 75 0>; - connectors = <&hdmi>; - gpus = <&gpu>; - clock-names = - "core_clk", - "iface_clk", - "lut_clk", - "src_clk", - "hdmi_clk", - "mdp_clk"; - clocks = - <&mmcc MDP_SRC>, - <&mmcc MDP_AHB_CLK>, - <&mmcc MDP_LUT_CLK>, - <&mmcc TV_SRC>, - <&mmcc HDMI_TV_CLK>, - <&mmcc MDP_TV_CLK>; - }; -}; diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt deleted file mode 100644 index 4ab9e2300..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt +++ /dev/null @@ -1,66 +0,0 @@ -Device-Tree bindings for tilcdc DRM generic panel output driver - -Required properties: - - compatible: value should be "ti,tilcdc,panel". - - panel-info: configuration info to configure LCDC correctly for the panel - - ac-bias: AC Bias Pin Frequency - - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt - - dma-burst-sz: DMA burst size - - bpp: Bits per pixel - - fdd: FIFO DMA Request Delay - - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling - - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore - - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most - - fifo-th: DMA FIFO threshold - - display-timings: typical videomode of lcd panel. Multiple video modes - can be listed if the panel supports multiple timings, but the 'native-mode' - should be the preferred/default resolution. Refer to - Documentation/devicetree/bindings/video/display-timing.txt for display - timing binding details. - -Optional properties: -- backlight: phandle of the backlight device attached to the panel -- enable-gpios: GPIO pin to enable or disable the panel - -Recommended properties: - - pinctrl-names, pinctrl-0: the pincontrol settings to configure - muxing properly for pins that connect to TFP410 device - -Example: - - /* Settings for CDTech_S035Q01 / LCD3 cape: */ - lcd3 { - compatible = "ti,tilcdc,panel"; - pinctrl-names = "default"; - pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; - backlight = <&backlight>; - enable-gpios = <&gpio3 19 0>; - - panel-info { - ac-bias = <255>; - ac-bias-intrpt = <0>; - dma-burst-sz = <16>; - bpp = <16>; - fdd = <0x80>; - sync-edge = <0>; - sync-ctrl = <1>; - raster-order = <0>; - fifo-th = <0>; - }; - display-timings { - native-mode = <&timing0>; - timing0: 320x240 { - hactive = <320>; - vactive = <240>; - hback-porch = <21>; - hfront-porch = <58>; - hsync-len = <47>; - vback-porch = <11>; - vfront-porch = <23>; - vsync-len = <2>; - clock-frequency = <8000000>; - hsync-active = <0>; - vsync-active = <0>; - }; - }; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt deleted file mode 100644 index 3d2c52460..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt +++ /dev/null @@ -1,18 +0,0 @@ -Device-Tree bindings for tilcdc DRM encoder slave output driver - -Required properties: - - compatible: value should be "ti,tilcdc,slave". - - i2c: the phandle for the i2c device the encoder slave is connected to - -Recommended properties: - - pinctrl-names, pinctrl-0: the pincontrol settings to configure - muxing properly for pins that connect to TFP410 device - -Example: - - hdmi { - compatible = "ti,tilcdc,slave"; - i2c = <&i2c0>; - pinctrl-names = "default"; - pinctrl-0 = <&nxp_hdmi_bonelt_pins>; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt deleted file mode 100644 index a58ae7756..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt +++ /dev/null @@ -1,21 +0,0 @@ -Device-Tree bindings for tilcdc DRM TFP410 output driver - -Required properties: - - compatible: value should be "ti,tilcdc,tfp410". - - i2c: the phandle for the i2c device to use for DDC - -Recommended properties: - - pinctrl-names, pinctrl-0: the pincontrol settings to configure - muxing properly for pins that connect to TFP410 device - - powerdn-gpio: the powerdown GPIO, pulled low to power down the - TFP410 device (for DPMS_OFF) - -Example: - - dvicape { - compatible = "ti,tilcdc,tfp410"; - i2c = <&i2c2>; - pinctrl-names = "default"; - pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>; - powerdn-gpio = <&gpio2 31 0>; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt deleted file mode 100644 index fff10da5e..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt +++ /dev/null @@ -1,29 +0,0 @@ -Device-Tree bindings for tilcdc DRM driver - -Required properties: - - compatible: value should be "ti,am33xx-tilcdc". - - interrupts: the interrupt number - - reg: base address and size of the LCDC device - -Recommended properties: - - interrupt-parent: the phandle for the interrupt controller that - services interrupts for this device. - - ti,hwmods: Name of the hwmod associated to the LCDC - -Optional properties: - - max-bandwidth: The maximum pixels per second that the memory - interface / lcd controller combination can sustain - - max-width: The maximum horizontal pixel width supported by - the lcd controller. - - max-pixelclock: The maximum pixel clock that can be supported - by the lcd controller in KHz. - -Example: - - fb: fb@4830e000 { - compatible = "ti,am33xx-tilcdc"; - reg = <0x4830e000 0x1000>; - interrupt-parent = <&intc>; - interrupts = <36>; - ti,hwmods = "lcdc"; - }; |