summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/devicetree/bindings/drm
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/drm')
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt30
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt53
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt50
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/i2c/tda998x.txt29
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt83
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/imx/hdmi.txt58
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt146
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/msm/gpu.txt52
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/msm/hdmi.txt48
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/msm/mdp.txt48
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt66
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt18
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt21
-rw-r--r--kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt29
14 files changed, 731 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt b/kernel/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt
new file mode 100644
index 000000000..46525ea3e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt
@@ -0,0 +1,30 @@
+Device Tree bindings for Armada DRM CRTC driver
+
+Required properties:
+ - compatible: value should be "marvell,dove-lcd".
+ - reg: base address and size of the LCD controller
+ - interrupts: single interrupt number for the LCD controller
+ - port: video output port with endpoints, as described by graph.txt
+
+Optional properties:
+
+ - clocks: as described by clock-bindings.txt
+ - clock-names: as described by clock-bindings.txt
+ "axiclk" - axi bus clock for pixel clock
+ "plldivider" - pll divider clock for pixel clock
+ "ext_ref_clk0" - external clock 0 for pixel clock
+ "ext_ref_clk1" - external clock 1 for pixel clock
+
+Note: all clocks are optional but at least one must be specified.
+Further clocks may be added in the future according to requirements of
+different SoCs.
+
+Example:
+
+ lcd0: lcd-controller@820000 {
+ compatible = "marvell,dove-lcd";
+ reg = <0x820000 0x1000>;
+ interrupts = <47>;
+ clocks = <&si5351 0>;
+ clock-names = "ext_ref_clk_1";
+ };
diff --git a/kernel/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt b/kernel/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt
new file mode 100644
index 000000000..ebc1a914b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt
@@ -0,0 +1,53 @@
+Device-Tree bindings for Atmel's HLCDC (High LCD Controller) DRM driver
+
+The Atmel HLCDC Display Controller is subdevice of the HLCDC MFD device.
+See ../mfd/atmel-hlcdc.txt for more details.
+
+Required properties:
+ - compatible: value should be "atmel,hlcdc-display-controller"
+ - pinctrl-names: the pin control state names. Should contain "default".
+ - pinctrl-0: should contain the default pinctrl states.
+ - #address-cells: should be set to 1.
+ - #size-cells: should be set to 0.
+
+Required children nodes:
+ Children nodes are encoding available output ports and their connections
+ to external devices using the OF graph reprensentation (see ../graph.txt).
+ At least one port node is required.
+
+Example:
+
+ hlcdc: hlcdc@f0030000 {
+ compatible = "atmel,sama5d3-hlcdc";
+ reg = <0xf0030000 0x2000>;
+ interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+ clock-names = "periph_clk","sys_clk", "slow_clk";
+ status = "disabled";
+
+ hlcdc-display-controller {
+ compatible = "atmel,hlcdc-display-controller";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ hlcdc_panel_output: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+ };
+ };
+
+ hlcdc_pwm: hlcdc-pwm {
+ compatible = "atmel,hlcdc-pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_pwm>;
+ #pwm-cells = <3>;
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt b/kernel/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt
new file mode 100644
index 000000000..a905c1413
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt
@@ -0,0 +1,50 @@
+DesignWare HDMI bridge bindings
+
+Required properties:
+- compatible: platform specific such as:
+ * "snps,dw-hdmi-tx"
+ * "fsl,imx6q-hdmi"
+ * "fsl,imx6dl-hdmi"
+ * "rockchip,rk3288-dw-hdmi"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The HDMI interrupt number
+- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks,
+ as described in Documentation/devicetree/bindings/clock/clock-bindings.txt,
+ the clocks are soc specific, the clock-names should be "iahb", "isfr"
+-port@[X]: SoC specific port nodes with endpoint definitions as defined
+ in Documentation/devicetree/bindings/media/video-interfaces.txt,
+ please refer to the SoC specific binding document:
+ * Documentation/devicetree/bindings/drm/imx/hdmi.txt
+ * Documentation/devicetree/bindings/video/dw_hdmi-rockchip.txt
+
+Optional properties
+- reg-io-width: the width of the reg:1,4, default set to 1 if not present
+- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec"
+
+Example:
+ hdmi: hdmi@0120000 {
+ compatible = "fsl,imx6q-hdmi";
+ reg = <0x00120000 0x9000>;
+ interrupts = <0 115 0x04>;
+ gpr = <&gpr>;
+ clocks = <&clks 123>, <&clks 124>;
+ clock-names = "iahb", "isfr";
+ ddc-i2c-bus = <&i2c2>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/drm/i2c/tda998x.txt b/kernel/Documentation/devicetree/bindings/drm/i2c/tda998x.txt
new file mode 100644
index 000000000..e9e4bce40
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/i2c/tda998x.txt
@@ -0,0 +1,29 @@
+Device-Tree bindings for the NXP TDA998x HDMI transmitter
+
+Required properties;
+ - compatible: must be "nxp,tda998x"
+
+ - reg: I2C address
+
+Optional properties:
+ - interrupts: interrupt number and trigger type
+ default: polling
+
+ - pinctrl-0: pin control group to be used for
+ screen plug/unplug interrupt.
+
+ - pinctrl-names: must contain a "default" entry.
+
+ - video-ports: 24 bits value which defines how the video controller
+ output is wired to the TDA998x input - default: <0x230145>
+
+Example:
+
+ tda998x: hdmi-encoder {
+ compatible = "nxp,tda998x";
+ reg = <0x70>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 2>; /* falling edge */
+ pinctrl-0 = <&pmx_camera>;
+ pinctrl-names = "default";
+ };
diff --git a/kernel/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt b/kernel/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt
new file mode 100644
index 000000000..e75f0e549
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt
@@ -0,0 +1,83 @@
+Freescale i.MX DRM master device
+================================
+
+The freescale i.MX DRM master device is a virtual device needed to list all
+IPU or other display interface nodes that comprise the graphics subsystem.
+
+Required properties:
+- compatible: Should be "fsl,imx-display-subsystem"
+- ports: Should contain a list of phandles pointing to display interface ports
+ of IPU devices
+
+example:
+
+display-subsystem {
+ compatible = "fsl,display-subsystem";
+ ports = <&ipu_di0>;
+};
+
+
+Freescale i.MX IPUv3
+====================
+
+Required properties:
+- compatible: Should be "fsl,<chip>-ipu"
+- reg: should be register base and length as documented in the
+ datasheet
+- interrupts: Should contain sync interrupt and error interrupt,
+ in this order.
+- resets: phandle pointing to the system reset controller and
+ reset line index, see reset/fsl,imx-src.txt for details
+Optional properties:
+- port@[0-3]: Port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+ Ports 0 and 1 should correspond to CSI0 and CSI1,
+ ports 2 and 3 should correspond to DI0 and DI1, respectively.
+
+example:
+
+ipu: ipu@18000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx53-ipu";
+ reg = <0x18000000 0x080000000>;
+ interrupts = <11 10>;
+ resets = <&src 2>;
+
+ ipu_di0: port@2 {
+ reg = <2>;
+
+ ipu_di0_disp0: endpoint {
+ remote-endpoint = <&display_in>;
+ };
+ };
+};
+
+Parallel display support
+========================
+
+Required properties:
+- compatible: Should be "fsl,imx-parallel-display"
+Optional properties:
+- interface_pix_fmt: How this display is connected to the
+ display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
+ and "lvds666".
+- edid: verbatim EDID data block describing attached display.
+- ddc: phandle describing the i2c bus handling the display data
+ channel
+- port: A port node with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+example:
+
+display@di0 {
+ compatible = "fsl,imx-parallel-display";
+ edid = [edid-data];
+ interface-pix-fmt = "rgb24";
+
+ port {
+ display_in: endpoint {
+ remote-endpoint = <&ipu_di0_disp0>;
+ };
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/drm/imx/hdmi.txt b/kernel/Documentation/devicetree/bindings/drm/imx/hdmi.txt
new file mode 100644
index 000000000..1b756cf9a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/imx/hdmi.txt
@@ -0,0 +1,58 @@
+Device-Tree bindings for HDMI Transmitter
+
+HDMI Transmitter
+================
+
+The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+with accompanying PHY IP.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
+ - gpr : should be <&gpr>.
+ The phandle points to the iomuxc-gpr region containing the HDMI
+ multiplexer control register.
+ - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described
+ in Documentation/devicetree/bindings/clock/clock-bindings.txt and
+ Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+ - port@[0-4]: Up to four port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt,
+ corresponding to the four inputs to the HDMI multiplexer.
+
+Optional properties:
+ - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+
+example:
+
+ gpr: iomuxc-gpr@020e0000 {
+ /* ... */
+ };
+
+ hdmi: hdmi@0120000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-hdmi";
+ reg = <0x00120000 0x9000>;
+ interrupts = <0 115 0x04>;
+ gpr = <&gpr>;
+ clocks = <&clks 123>, <&clks 124>;
+ clock-names = "iahb", "isfr";
+ ddc-i2c-bus = <&i2c2>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt b/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt
new file mode 100644
index 000000000..9a2136643
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/imx/ldb.txt
@@ -0,0 +1,146 @@
+Device-Tree bindings for LVDS Display Bridge (ldb)
+
+LVDS Display Bridge
+===================
+
+The LVDS Display Bridge device tree node contains up to two lvds-channel
+nodes describing each of the two LVDS encoder channels of the bridge.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
+ Both LDB versions are similar, but i.MX6 has an additional
+ multiplexer in the front to select any of the four IPU display
+ interfaces as input for each LVDS channel.
+ - gpr : should be <&gpr> on i.MX53 and i.MX6q.
+ The phandle points to the iomuxc-gpr region containing the LVDS
+ control register.
+- clocks, clock-names : phandles to the LDB divider and selector clocks and to
+ the display interface selector clocks, as described in
+ Documentation/devicetree/bindings/clock/clock-bindings.txt
+ The following clocks are expected on i.MX53:
+ "di0_pll" - LDB LVDS channel 0 mux
+ "di1_pll" - LDB LVDS channel 1 mux
+ "di0" - LDB LVDS channel 0 gate
+ "di1" - LDB LVDS channel 1 gate
+ "di0_sel" - IPU1 DI0 mux
+ "di1_sel" - IPU1 DI1 mux
+ On i.MX6q the following additional clocks are needed:
+ "di2_sel" - IPU2 DI0 mux
+ "di3_sel" - IPU2 DI1 mux
+ The needed clock numbers for each are documented in
+ Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
+ Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+
+Optional properties:
+ - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
+ - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
+ not used on i.MX6q
+ - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
+ be configured - one input will be distributed on both outputs in dual
+ channel mode
+
+LVDS Channel
+============
+
+Each LVDS Channel has to contain either an of graph link to a panel device node
+or a display-timings node that describes the video timings for the connected
+LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
+
+Required properties:
+ - reg : should be <0> or <1>
+ - port: Input and output port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/graph.txt.
+ On i.MX5, the internal two-input-multiplexer is used. Due to hardware
+ limitations, only one input port (port@[0,1]) can be used for each channel
+ (lvds-channel@[0,1], respectively).
+ On i.MX6, there should be four input ports (port@[0-3]) that correspond
+ to the four LVDS multiplexer inputs.
+ A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
+ to a panel input port. Optionally, the output port can be left out if
+ display-timings are used instead.
+
+Optional properties (required if display-timings are used):
+ - display-timings : A node that describes the display timings as defined in
+ Documentation/devicetree/bindings/video/display-timing.txt.
+ - fsl,data-mapping : should be "spwg" or "jeida"
+ This describes how the color bits are laid out in the
+ serialized LVDS signal.
+ - fsl,data-width : should be <18> or <24>
+
+example:
+
+gpr: iomuxc-gpr@53fa8000 {
+ /* ... */
+};
+
+ldb: ldb@53fa8008 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx53-ldb";
+ gpr = <&gpr>;
+ clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
+ <&clks IMX5_CLK_LDB_DI1_SEL>,
+ <&clks IMX5_CLK_IPU_DI0_SEL>,
+ <&clks IMX5_CLK_IPU_DI1_SEL>,
+ <&clks IMX5_CLK_LDB_DI0_GATE>,
+ <&clks IMX5_CLK_LDB_DI1_GATE>;
+ clock-names = "di0_pll", "di1_pll",
+ "di0_sel", "di1_sel",
+ "di0", "di1";
+
+ /* Using an of-graph endpoint link to connect the panel */
+ lvds-channel@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lvds0_in: endpoint {
+ remote-endpoint = <&ipu_di0_lvds0>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ /* Using display-timings and fsl,data-mapping/width instead */
+ lvds-channel@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+
+ display-timings {
+ /* ... */
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lvds1_in: endpoint {
+ remote-endpoint = <&ipu_di1_lvds1>;
+ };
+ };
+ };
+};
+
+panel: lvds-panel {
+ /* ... */
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/drm/msm/gpu.txt b/kernel/Documentation/devicetree/bindings/drm/msm/gpu.txt
new file mode 100644
index 000000000..67d0a58db
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/msm/gpu.txt
@@ -0,0 +1,52 @@
+Qualcomm adreno/snapdragon GPU
+
+Required properties:
+- compatible: "qcom,adreno-3xx"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt signal from the gpu.
+- clocks: device clocks
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+ * "core_clk"
+ * "iface_clk"
+ * "mem_iface_clk"
+- qcom,chipid: gpu chip-id. Note this may become optional for future
+ devices if we can reliably read the chipid from hw
+- qcom,gpu-pwrlevels: list of operating points
+ - compatible: "qcom,gpu-pwrlevels"
+ - for each qcom,gpu-pwrlevel:
+ - qcom,gpu-freq: requested gpu clock speed
+ - NOTE: downstream android driver defines additional parameters to
+ configure memory bandwidth scaling per OPP.
+
+Example:
+
+/ {
+ ...
+
+ gpu: qcom,kgsl-3d0@4300000 {
+ compatible = "qcom,adreno-3xx";
+ reg = <0x04300000 0x20000>;
+ reg-names = "kgsl_3d0_reg_memory";
+ interrupts = <GIC_SPI 80 0>;
+ interrupt-names = "kgsl_3d0_irq";
+ clock-names =
+ "core_clk",
+ "iface_clk",
+ "mem_iface_clk";
+ clocks =
+ <&mmcc GFX3D_CLK>,
+ <&mmcc GFX3D_AHB_CLK>,
+ <&mmcc MMSS_IMEM_AHB_CLK>;
+ qcom,chipid = <0x03020100>;
+ qcom,gpu-pwrlevels {
+ compatible = "qcom,gpu-pwrlevels";
+ qcom,gpu-pwrlevel@0 {
+ qcom,gpu-freq = <450000000>;
+ };
+ qcom,gpu-pwrlevel@1 {
+ qcom,gpu-freq = <27000000>;
+ };
+ };
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/drm/msm/hdmi.txt b/kernel/Documentation/devicetree/bindings/drm/msm/hdmi.txt
new file mode 100644
index 000000000..a29a55f3d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/msm/hdmi.txt
@@ -0,0 +1,48 @@
+Qualcomm adreno/snapdragon hdmi output
+
+Required properties:
+- compatible: one of the following
+ * "qcom,hdmi-tx-8084"
+ * "qcom,hdmi-tx-8074"
+ * "qcom,hdmi-tx-8660"
+ * "qcom,hdmi-tx-8960"
+- reg: Physical base address and length of the controller's registers
+- reg-names: "core_physical"
+- interrupts: The interrupt signal from the hdmi block.
+- clocks: device clocks
+ See ../clocks/clock-bindings.txt for details.
+- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
+- qcom,hdmi-tx-ddc-data-gpio: ddc data pin
+- qcom,hdmi-tx-hpd-gpio: hpd pin
+- core-vdda-supply: phandle to supply regulator
+- hdmi-mux-supply: phandle to mux regulator
+
+Optional properties:
+- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
+- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin
+
+Example:
+
+/ {
+ ...
+
+ hdmi: qcom,hdmi-tx-8960@4a00000 {
+ compatible = "qcom,hdmi-tx-8960";
+ reg-names = "core_physical";
+ reg = <0x04a00000 0x1000>;
+ interrupts = <GIC_SPI 79 0>;
+ clock-names =
+ "core_clk",
+ "master_iface_clk",
+ "slave_iface_clk";
+ clocks =
+ <&mmcc HDMI_APP_CLK>,
+ <&mmcc HDMI_M_AHB_CLK>,
+ <&mmcc HDMI_S_AHB_CLK>;
+ qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>;
+ qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>;
+ qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>;
+ core-vdda-supply = <&pm8921_hdmi_mvs>;
+ hdmi-mux-supply = <&ext_3p3v>;
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/drm/msm/mdp.txt b/kernel/Documentation/devicetree/bindings/drm/msm/mdp.txt
new file mode 100644
index 000000000..1a0598e52
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/msm/mdp.txt
@@ -0,0 +1,48 @@
+Qualcomm adreno/snapdragon display controller
+
+Required properties:
+- compatible:
+ * "qcom,mdp" - mdp4
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt signal from the display controller.
+- connectors: array of phandles for output device(s)
+- clocks: device clocks
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+ * "core_clk"
+ * "iface_clk"
+ * "lut_clk"
+ * "src_clk"
+ * "hdmi_clk"
+ * "mpd_clk"
+
+Optional properties:
+- gpus: phandle for gpu device
+
+Example:
+
+/ {
+ ...
+
+ mdp: qcom,mdp@5100000 {
+ compatible = "qcom,mdp";
+ reg = <0x05100000 0xf0000>;
+ interrupts = <GIC_SPI 75 0>;
+ connectors = <&hdmi>;
+ gpus = <&gpu>;
+ clock-names =
+ "core_clk",
+ "iface_clk",
+ "lut_clk",
+ "src_clk",
+ "hdmi_clk",
+ "mdp_clk";
+ clocks =
+ <&mmcc MDP_SRC>,
+ <&mmcc MDP_AHB_CLK>,
+ <&mmcc MDP_LUT_CLK>,
+ <&mmcc TV_SRC>,
+ <&mmcc HDMI_TV_CLK>,
+ <&mmcc MDP_TV_CLK>;
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt
new file mode 100644
index 000000000..4ab9e2300
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt
@@ -0,0 +1,66 @@
+Device-Tree bindings for tilcdc DRM generic panel output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,panel".
+ - panel-info: configuration info to configure LCDC correctly for the panel
+ - ac-bias: AC Bias Pin Frequency
+ - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt
+ - dma-burst-sz: DMA burst size
+ - bpp: Bits per pixel
+ - fdd: FIFO DMA Request Delay
+ - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling
+ - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore
+ - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most
+ - fifo-th: DMA FIFO threshold
+ - display-timings: typical videomode of lcd panel. Multiple video modes
+ can be listed if the panel supports multiple timings, but the 'native-mode'
+ should be the preferred/default resolution. Refer to
+ Documentation/devicetree/bindings/video/display-timing.txt for display
+ timing binding details.
+
+Optional properties:
+- backlight: phandle of the backlight device attached to the panel
+- enable-gpios: GPIO pin to enable or disable the panel
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+ muxing properly for pins that connect to TFP410 device
+
+Example:
+
+ /* Settings for CDTech_S035Q01 / LCD3 cape: */
+ lcd3 {
+ compatible = "ti,tilcdc,panel";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bone_lcd3_cape_lcd_pins>;
+ backlight = <&backlight>;
+ enable-gpios = <&gpio3 19 0>;
+
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <16>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 320x240 {
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <21>;
+ hfront-porch = <58>;
+ hsync-len = <47>;
+ vback-porch = <11>;
+ vfront-porch = <23>;
+ vsync-len = <2>;
+ clock-frequency = <8000000>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ };
+ };
+ };
diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt
new file mode 100644
index 000000000..3d2c52460
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt
@@ -0,0 +1,18 @@
+Device-Tree bindings for tilcdc DRM encoder slave output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,slave".
+ - i2c: the phandle for the i2c device the encoder slave is connected to
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+ muxing properly for pins that connect to TFP410 device
+
+Example:
+
+ hdmi {
+ compatible = "ti,tilcdc,slave";
+ i2c = <&i2c0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ };
diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt
new file mode 100644
index 000000000..a58ae7756
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt
@@ -0,0 +1,21 @@
+Device-Tree bindings for tilcdc DRM TFP410 output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,tfp410".
+ - i2c: the phandle for the i2c device to use for DDC
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+ muxing properly for pins that connect to TFP410 device
+ - powerdn-gpio: the powerdown GPIO, pulled low to power down the
+ TFP410 device (for DPMS_OFF)
+
+Example:
+
+ dvicape {
+ compatible = "ti,tilcdc,tfp410";
+ i2c = <&i2c2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>;
+ powerdn-gpio = <&gpio2 31 0>;
+ };
diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
new file mode 100644
index 000000000..fff10da5e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
@@ -0,0 +1,29 @@
+Device-Tree bindings for tilcdc DRM driver
+
+Required properties:
+ - compatible: value should be "ti,am33xx-tilcdc".
+ - interrupts: the interrupt number
+ - reg: base address and size of the LCDC device
+
+Recommended properties:
+ - interrupt-parent: the phandle for the interrupt controller that
+ services interrupts for this device.
+ - ti,hwmods: Name of the hwmod associated to the LCDC
+
+Optional properties:
+ - max-bandwidth: The maximum pixels per second that the memory
+ interface / lcd controller combination can sustain
+ - max-width: The maximum horizontal pixel width supported by
+ the lcd controller.
+ - max-pixelclock: The maximum pixel clock that can be supported
+ by the lcd controller in KHz.
+
+Example:
+
+ fb: fb@4830e000 {
+ compatible = "ti,am33xx-tilcdc";
+ reg = <0x4830e000 0x1000>;
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+ ti,hwmods = "lcdc";
+ };