diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/drm/tilcdc')
4 files changed, 0 insertions, 134 deletions
diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt deleted file mode 100644 index 4ab9e2300..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/panel.txt +++ /dev/null @@ -1,66 +0,0 @@ -Device-Tree bindings for tilcdc DRM generic panel output driver - -Required properties: - - compatible: value should be "ti,tilcdc,panel". - - panel-info: configuration info to configure LCDC correctly for the panel - - ac-bias: AC Bias Pin Frequency - - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt - - dma-burst-sz: DMA burst size - - bpp: Bits per pixel - - fdd: FIFO DMA Request Delay - - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling - - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore - - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most - - fifo-th: DMA FIFO threshold - - display-timings: typical videomode of lcd panel. Multiple video modes - can be listed if the panel supports multiple timings, but the 'native-mode' - should be the preferred/default resolution. Refer to - Documentation/devicetree/bindings/video/display-timing.txt for display - timing binding details. - -Optional properties: -- backlight: phandle of the backlight device attached to the panel -- enable-gpios: GPIO pin to enable or disable the panel - -Recommended properties: - - pinctrl-names, pinctrl-0: the pincontrol settings to configure - muxing properly for pins that connect to TFP410 device - -Example: - - /* Settings for CDTech_S035Q01 / LCD3 cape: */ - lcd3 { - compatible = "ti,tilcdc,panel"; - pinctrl-names = "default"; - pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; - backlight = <&backlight>; - enable-gpios = <&gpio3 19 0>; - - panel-info { - ac-bias = <255>; - ac-bias-intrpt = <0>; - dma-burst-sz = <16>; - bpp = <16>; - fdd = <0x80>; - sync-edge = <0>; - sync-ctrl = <1>; - raster-order = <0>; - fifo-th = <0>; - }; - display-timings { - native-mode = <&timing0>; - timing0: 320x240 { - hactive = <320>; - vactive = <240>; - hback-porch = <21>; - hfront-porch = <58>; - hsync-len = <47>; - vback-porch = <11>; - vfront-porch = <23>; - vsync-len = <2>; - clock-frequency = <8000000>; - hsync-active = <0>; - vsync-active = <0>; - }; - }; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt deleted file mode 100644 index 3d2c52460..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/slave.txt +++ /dev/null @@ -1,18 +0,0 @@ -Device-Tree bindings for tilcdc DRM encoder slave output driver - -Required properties: - - compatible: value should be "ti,tilcdc,slave". - - i2c: the phandle for the i2c device the encoder slave is connected to - -Recommended properties: - - pinctrl-names, pinctrl-0: the pincontrol settings to configure - muxing properly for pins that connect to TFP410 device - -Example: - - hdmi { - compatible = "ti,tilcdc,slave"; - i2c = <&i2c0>; - pinctrl-names = "default"; - pinctrl-0 = <&nxp_hdmi_bonelt_pins>; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt deleted file mode 100644 index a58ae7756..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt +++ /dev/null @@ -1,21 +0,0 @@ -Device-Tree bindings for tilcdc DRM TFP410 output driver - -Required properties: - - compatible: value should be "ti,tilcdc,tfp410". - - i2c: the phandle for the i2c device to use for DDC - -Recommended properties: - - pinctrl-names, pinctrl-0: the pincontrol settings to configure - muxing properly for pins that connect to TFP410 device - - powerdn-gpio: the powerdown GPIO, pulled low to power down the - TFP410 device (for DPMS_OFF) - -Example: - - dvicape { - compatible = "ti,tilcdc,tfp410"; - i2c = <&i2c2>; - pinctrl-names = "default"; - pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>; - powerdn-gpio = <&gpio2 31 0>; - }; diff --git a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt deleted file mode 100644 index fff10da5e..000000000 --- a/kernel/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt +++ /dev/null @@ -1,29 +0,0 @@ -Device-Tree bindings for tilcdc DRM driver - -Required properties: - - compatible: value should be "ti,am33xx-tilcdc". - - interrupts: the interrupt number - - reg: base address and size of the LCDC device - -Recommended properties: - - interrupt-parent: the phandle for the interrupt controller that - services interrupts for this device. - - ti,hwmods: Name of the hwmod associated to the LCDC - -Optional properties: - - max-bandwidth: The maximum pixels per second that the memory - interface / lcd controller combination can sustain - - max-width: The maximum horizontal pixel width supported by - the lcd controller. - - max-pixelclock: The maximum pixel clock that can be supported - by the lcd controller in KHz. - -Example: - - fb: fb@4830e000 { - compatible = "ti,am33xx-tilcdc"; - reg = <0x4830e000 0x1000>; - interrupt-parent = <&intc>; - interrupts = <36>; - ti,hwmods = "lcdc"; - }; |